|
| 1 | Surface dressing n exc15 cm deep and getting out any type of soil complete all as specified and directed. |
| 2 | Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundation .etc in soft/loose soil complete all as specified and directed. |
| 3 | M&L for plain cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation, filling & mass concrete, sub base complete all as specified and directed. |
| 4 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick with soft/loose soil etc complete all as specified and directed. |
| 5 | Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed. |
| 6 | M&L for providing reinforced cement concrete (M-25) Design Mix using 20 mm graded stone aggregates as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed. |
| 7 | M&L for providing reinforced cement concrete (M-25) Design Mix using 20 mm graded stone aggregates as in Columns, pillars, piers, posts and struts complete all as specified and directed. |
| 8 | M&L for providing reinforced cement concrete (M-25) Design Mix using 20 mm graded stone aggregates as in Slabs supported on walls, beams and columns in floors, roofs, complete all as specified and directed. |
| 9 | M&L for providing reinforced cement concrete (M-25) Design Mix using 20 mm graded stone aggregates as in Roof beams, cantilevers, bressummers, lintel over 1.5 span complete all as specified and directed. |
| 10 | M&L for providing reinforced cement concrete (M-25) Design Mix using 20 mm graded stone aggregates as in Chajjas complete all as specified and directed. |
| 11 | M&L Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter (rough finished surface) complete all as specified and directed. |
| 12 | M&L Formwork to sides of pillars, posts, struts, piers, column sand stanchions (square/rectangular/polygonal) rough finished surface complete all as specified and directed. |
| 13 | M&L Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200 mm thick rough finished in flat surface complete all as specified and directed. |
| 14 | M&L Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors in rough finished flat surfaces and etc complete all as specified and directed. |
| 15 | M&L Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide (rough finished surface) complete all as specified and directed. |
| 16 | M&L for TMT bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips etc complete all as specified and directed. |
| 17 | All as per Sl item No.16 above, but 6 mm dia to 8 mm dia complete all as specified and directed. |
| 18 | All as per Sl item No. 16 here-in-before, but 5 mm dia & over upto & including 10 mm dia in stirrups, spacers and binders, complete all as specified and directed. |
| 19 | M&L for brickwork with fly ash old size bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed. |
| 20 | Excavating in post holes (or similar holes) each n.exc 0.5Cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25CM, in soft and loose soil complete all as specified and directed. |
| 21 | M&L cement concrete type B-2, 1:2:4 (40mm graded aggregate) as in foundations, filling and mass concrete in post, pillars complete all as specified and directed. |
| 22 | M&L Steel work in tubular/angle trusses or rectangular/ square hollow section including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete all as specified and directed. |
| 23 | M&L Plates (plain or chequered square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified and directed. |
| 24 | M&L Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required hooks (stay) heavy for large gates, hook, holdfast and pintle hinges large hasps and staples, chains, hand made sliding bolts, clamps, hold fasts, flat iron, wall ties, hooks for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed. |
| 25 | M&L preparation of new Steel surfaces of any description, not otherwise described, over 10cm width or girth & applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified and directed. |
| 26 | M&L pre-painted galvalume aluminium zinc coating GI based corrugated/semi corrugated/trapezoidal steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and directed. |
| 27 | M&L pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof ridge, valley gutter, covering/cladding to wall fixed with self tapping screws or \\"J\\" hook complete all as specified and directed. |
| 28 | M&L for Powder coated galvanised iron snap grid frame work of size 600 x 600 mm for false ceiling comprising of Main runner 'T' section of size 38mm x 24mm x 0.40mm thickness, Cross 'T' of size 29mm x 24mm x 0.3mm thickness and wall angle of size 24mm x 24mm x 0.43mm thick suspended with 2mm dia GI wire from purlin @ 1.20m c/c and fixed with 4mm thick designer ceiling boards complete all as specified and directed. |
| 29 | M&L for rendering 15 mm thick in cement mortar (1:6) on brick work or concrete surfaces finished even and fair (without using extra cement) complete all as specified and directed. |
| 30 | M&L for 15 mm thick plastering in cement mortar (1:4) on brick or concrete surfaces including rendering on fins, fascias, chajja, parapets etc and finishing the surfaces even and fair (without using extra cement), top layer shall be with WPC as per manufacturer's instruction and complete all as specified and directed. Note: WPC shall be measured and paid separately. |
| 31 | Extra for forming fair finished drain or channel inner girth in cement concrete, using extra cement, including forms, mounds, mitred/stopped end etc. complete all as specified and directed. |
| 32 | Supply only integral water proofing compound ISI Marked complete all as specified and directed. |
| 33 | M&L for preparation of new internal plaster surfaces applying two coats of oil bound distemper over a coat of alkhali resistant primer over a coat of wall care putty 1.5 mm thick complete all as specified and directed. |
| 34 | M&L preparation of newly plastered surfaces of wall and applying two coats of Weather proof Exterior Emulsion paint(camouflage design) over a coat of suitable primer on walls complete all as specified and directed. |
| 35 | M&L for Hardcore (broken stone or boulders) of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed. |
| 36 | M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed. |
| 37 | M&L for 75 mm thick cement concrete (1:4:8) type D-2 (using 40 mm graded stone aggregates) as in sub base of flooring etc complete all as specified and directed. |
| 38 | M&L for 25 mm thick Cement concrete type B-0 1:2:4 (12.5 mm graded aggregate) as in sub floors etc incl finishing the surface even & rough to receive screeding complete all as specified and directed. |
| 39 | M&L for joint free Vitrified Coloured Ceramic tiles 8- 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. laid over and including 15mm thick screed bed in CM 1:6 etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. |
| 40 | M&L for joint free Vitrified Coloured Ceramic tiles 8- 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in skirting/vertical surface laid over and including 10mm thick rendering in CM 1:4 etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. |
| 41 | M & L for non skid coloured ceramic floor tiles of size of tile exc. 0.11 but n.exc.0.18 sqm each 7-8 mm thick as in floor laid over and including 15mm thick screed bed in CM 1:6, set, jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. |
| 42 | M & L for coloured glazed ceramic wall tiles of size 450x300x6-7mm thick on vertical surfaces laid over and including for rendering 10mm thick in CM (1:4) on vertical surface of wall. cement screed bet set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. |
| 43 | M&L for Granite (of any type) tiles15-18 mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone laid over and including 15mm thick screed bed in CM 1:6, including grinding and polishing complete all as specified and directed. |
| 44 | M&L for PCC 1:2:4 type B1 (using 20mm graded stone aggregates) as in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, coping, bed plates and the like including weathering, slightly rounded or chamfered angles and throating including necessary form work, complete all as specified and directed. |
| 45 | M&L Forming Construction joint 30mm deep x 10mm wide filled with sealing compound grade A complete all as specified and directed. |
| 46 | M&L powder coated anodized aluminium frame for doors, windows ventilations with one or more rebates including joining cleat for fixing etc. complete all as specified and directed. |
| 47 | M&L powder coated Anodised aluminium window and ventilator shutters side hung type without sash bar, aluminium sections weighing 0.55 kg/m including necessary joining, cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as hinges type B-21 100 mm long (2 nos) suitable handle 1 No complete all as specified and directed. |
| 48 | M&L powder coated aluminium sliding window shutters with frames (consisting of 02 Nos glazed shutters and 01 No gauze shutter) Series -D (25mm), 3 track sliding shutters, duly fitted with neoprene beading, glazing clips, locking device, heat absorbing glass 5.5 mm nominal thickness in glazed shutters, stainless steel wire mesh of 0.254mm nominal dia of wire and 0.95 mm average width of aperture in gauzed shutter and powder coated aluminium grill 4mm dia, 75 x 75mm aperture fixed with standard aluminium beading fixed in outer portion of the chowkat complete all as specified and directed. |
| 49 | M&L 4 mm thick one side frosted sheet glass ordinary quality and glazing in square n.exc 0.5sqm in each pane fixed with neopune rubber gasket in aluminium frame complete all as specified and directed. |
| 50 | M&L Solid PVC door frame of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet reinforced with M.S. tube, supplying & fixing in opening as per specification & drawings complete all as specified and directed. |
| 51 | M&L Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed. |
| 52 | M&L pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates etc complete size of frame 105mm X 60mm complete all as specified and directed. |
| 53 | M&L for PCC type C1,1:3:6 (using 20 mm graded aggregate) for holdfast blocks complete all as specified and directed. |
| 54 | M&L factory made 35mm thick flush shutters solid core construction with block board core and plywood face panel commercial type on both faces complete all as specified and directed. |
| 55 | M & L for Preparation of new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel painting over a coat of pink primer complete all as specified and directed. |
| 56 | M&L 25 mm outer dia medium weight pipe and end clamps with ornamental knobs for sides made out of stainless steel 304 grade, curtain rods to fixed to walls complete all as specified and directed. |
| 57 | S&F aluminium (extruded section body) door closer hydraulically regulated, designation No 3, universal type, suitable for door shutters 851 mm to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed. |
| 58 | S & F 100 mm Butt hinges, medium weight cold rolled, stainless steel and fixed complete all as specified and directed |
| 59 | S&F 150mm long aluminium anodised tower bolts of extruded section and fixed, complete all as specified and directed. |
| 60 | S&F 200 mm long aluminium anodised tower bolts of extruded section and fixed, complete all as specified and directed. |
| 61 | S&F 150mm size extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed. |
| 62 | S&F 300 mm aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and staples complete all as specified and directed. |
| 63 | M&L 110mm bore PVC (SWR) pipe single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed. |
| 64 | M&L 110 mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed. |
| 65 | M&L 75 mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed. |
| 66 | M&L 50 mm bore Low density poly ethylene pipes (LDPE) of pressure rating 6 kg/ cm2 laid in trenches or in floors complete all as specified and directed. |
| 67 | S&F PVC (SWR) vent cowl 110mm bore complete all as specified and directed. |
| 68 | S&F 110 mm bore PVC (SWR) bend any radius complete all as specified and directed. |
| 69 | S&F 75 mm bore PVC (SWR) bend any radius complete all as specified and directed. |
| 70 | S&F PVC (SWR) floor trap plain with grating having dia meter of out let 75mm including jointing with solvent cement to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed. |
| 71 | S&F white vitreous China wash down water closet pan (pedestal) pattern, and trap (excluding) fixing bolts, flushing cistern and flush pipe) including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc. complete all as specified and directed. |
| 72 | S&F plastic water closet sheet covers white closed pattern with flat bottom, with steel chromium plated or aluminised hinging device complete all as specified and directed. |
| 73 | S&F PVC white low level flushing cistern 10 ltr capacity with all fittings syphonic action type with inlet ball valve and float, handle with & including bracket and PVC flush pipe 32 mm bore complete all as specified and directed. |
| 74 | S&F Health faucet (ABS Body) steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed. |
| 75 | S&F vitreous china wash hand basin (flat back) of size 550x400mm including one number chromium plated waste fittings, 32 mm dia, brass with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed, with & including 32 mm dia PVC waste pipe with connector, including cutting for and pinning in ends of brackets complete all as specified and directed. |
| 76 | S&F 15 mm bore chromium plated fancy type pillar tap for WHBs with capstan heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe and fixed complete all as specified and directed. |
| 77 | S&F Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (Including flushing cistern, flush pipe and waste pipe), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe complete all as specified and directed. |
| 78 | S&F PVC connection 15mm dia and 450 mm long with 2 Nos PTMT nuts with washers complete all as specified and directed. |
| 79 | S&F CP soap dish fixed to wall with screw complete all as specified and directed. |
| 80 | S&F 15 mm bore chromium plated fancy type bib tap with crutch or buttrfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed. |
| 81 | S&F 15 mm bore chromium plated fancy type angle valve with elegant knob screwed down high pressure, with crutch or butter fly handle screwed for iron pipe or for unions complete all as specified and directed. |
| 82 | S&F CP toilet paper holder with flat recessed type stainless steel fixed to walls with chromium plated brass screws complete all as specified and directed. |
| 83 | S&F 20 mm dia Aluminium anodised tubular towel rail, D type, 60 cm long between flanges fixed with brass screws complete all as specified and directed. |
| 84 | S&F 600 mm x 450 mm size bevelled edge mirror of selected quality glass, 5.50 mm thick, mounted on 6mm thick AC pain building board or commercial plywood and fixed to wall with wooden plugs and chromium plated brass screws & cup washers complete all as specified and directed. |
| 85 | M&L 4 mm thick one side frosted sheet glass ordinary quality and glazing in square n.exc 0.5sqm in each pane fixed with neopune rubber gasket in aluminium frame complete all as specified and directed. |
| 86 | M & L for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed. |
| 87 | M&L 50 mm bore Low density poly ethylene pipes (LDPE) of pressure 6 kg/ cm2 laid in trenches or in floors complete all as specified and directed |
| 88 | M&L for cutting chases, pinning in making good to facing where required for concealed water tubing etc n. exc 10 cm girth in brick wall complete all as specified and directed. |
| 89 | Supplying and laying of 16mm CPVC pipe SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed. |
| 90 | Supplying and laying of 20mm CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed. |
| 91 | S&F 500 litres capacity rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR part I complete all as specified and directed. |
| 92 | S&F ball valve 20mm high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball complete all as specified and directed. |
| 93 | S & F 20mm bore gate valve with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and directed. |
| 94 | Surface Excavation in any type of soil n exc 30 cm deep and averaging 15 cm deep and getting out any type of soil complete all as specified and directed. |
| 95 | M&L for Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 complete all as specified and directed. |
| 96 | M&L for 100 mm thick cement concrete (1:4:8) type D-2 with using 40 mm graded stone aggregates) as in sub base of flooring etc complete all as specified and directed. |
| 97 | M & L for sand cushioning to receive interlocking tiles incl spreading, levelling in layers complete all as specified and directed. |
| 98 | M & L Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade With Grey Cement and pigment complete all as specified and directed. |
| 99 | M&L for designed, pre painted coloured chequered cement concrete tiles 300x300x25mm thick with grey cement and pigments set, jointed & pointed in neat cement slurry, laid over 20mm thick screed bed in CM 1:6 finished with pigments match the shade of tiles complete all as specified and directed. |
| 100 | Removing excavated materials (Soils) to a distance not exc. 50m and depositing where directed at a level not exc. 1.5m above the starting point complete all as specified and directed. |
| 101 | M&L Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed. |
| 102 | Excavating in post holes (or similar holes) each n.exc 0.5Cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25CM, in soft and loose soil complete all as specified and directed. |
| 103 | M&L cement concrete type B-2, 1:2:4 (40mm graded aggregate) as in foundations, filling and mass concrete in post, pillars complete all as specified and directed. |
| 104 | Supply only Chain link MS galvanised fencing, any size or type, weight not exceeding 4kg per sqm complete all as specified and directed. |
| 105 | Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete all as specified and directed. |
| 106 | M&L steel farmed work as in doors, gates of angle iron, flat iron or other section with gusset plates, rails, braces, hold fast, pin and pintol hinges, sliding bolt etc. complete, drilled for fixing of steel sheeting or other covering. Doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fitting (exclusive of steel sheeting or other covering, running rails and guides ) and hanging; also fastening and fixing complete all as specified and directed. |
| 107 | M&L steel works as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to e-290 Gde E-165 complete all as specified and directed. |
| 108 | Supply only Steel round bar 10 mm dia and over for tying chain link fencing etc complete all as specified and directed. |
| 109 | Supply only screw bolts (machine made) with hexagonal or square head at one end and rounded the other or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 5 cm but n.exc 10 cm and dia of shank 11 to 15mm and fixed in position complete all as specified and directed. |
| 110 | M&L for preparation of new steel surfaces of any description, over 10cm in width or girth,not otherwise described and applying two coats of synthetic enamel paint over a coat of redoxide primer complete all as specified and directed |
| 111 | M&L for preparation of new or untreated steel and iron surfaces of any description not exc.10 cm in width or girth when unconnected with other painting or when painted in a different tint and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 112 | M&L in repairs, Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified and directed. |
| 113 | Excavation in trenches in soft/loose soil not exceeding 1.5 m wide and not exc 1.5 m in depth for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc complete all as specified and directed. |
| 114 | M&L for Reinforced concrete pipes, class NP2, bore of pipe 150 mm laid and jointed complete with collars complete all as specified and directed. |
| 115 | M&L for cement concrete type C-2 (1:3:6) bed to drain pipes of 150 mm bore including packing under, and hunching against the sides of pipes after they are laid and tested in complete all as specified and directed. |
| 116 | M& L for PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in foundation or mass concrete complete all as specified and directed. |
| 117 | M&L for brick work with sub class B bricks built in cement mortar 1:4 straight or curved on plan exc 6 mtr mean radius complete all as specified and directed. |
| 118 | M&L for 15 mm thick Rendering in cement mortar (1:4) mixed with water proofing compound, on fair faces of brick or concrete surfaces, as in internal surfaces of manholes complete all as specified and directed. |
| 119 | M&L for PCC 1:2:4 type B-2 (using 40mm graded stone agg) as in surface channel bed/ drains/ in manholes all as specified laid to slope and finished surface even and fair complete all as specified and directed. |
| 120 | Extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement incl forms moulds, mitered/stopped ends etc. complete all as specified and directed. |
| 121 | M&L for Precast RCC (1:2:4) type B-1 using 20mm graded stone aggregates as in cover slab, set in cement mortar (1:6) complete all as specified and directed. |
| 122 | M&L 6 to 8 mm dia and over Thermo mechanically treated (TMT) bars, cut to length, bent to shape required including cranking, hooking ends and binding with and including steel wire (annealed) not less than 0.90 mm dia complete all as specified and directed. |
| 123 | Removing excavated materials (Soils) to a distance not exc. 50m and depositing where directed at a level not exc. 1.5m above the starting point complete all as specified and directed. |
| 124 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed. |
| 125 | M&L for soakage well including excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size of 2.40m dia and 3.00 m effective depth complete all as specified and directed. |
| 126 | M&L for on site LLDPE septic tank designed to carry sewage and selvage water, excavation in any type of soil, PCC 1:4:8 below foundation, Vent shaft, connection etc., complete for 25 users complete all as specified and directed. |
| 127 | M&L for Point wiring with 1.5 Sqmm (22/0.30mm) PVC insulated and unsheathed multistranded copper conductor cable, 1100 volts grade, ISI marked, FRLS type drawn through and including PVC concealed conduit (ISI marked) of adequate size and its accessories with sunk cast iron/pressed steel terminal boxes of size 1.6mm thick, with 3mm thick plastic laminated sheet cover of adequate size for one light or one fan point controlled by one switch incl 1.5 Sqmm (nominal area) copper conductor cable (multistrand), FRLS type, PVC insulated and unsheathed with colour code earth wire connected to common earth dolly at one end and metallic bodies of luminaires/ fan at other end complete as per site requirement and complete all as specified and directed for the following:- (a) One light point or one fan point controlled by one switch with cables 1.5 sq. mm size Note:- Unit rate include for cutting chases for conduits and sinking for boxes and making good to wall, floors etc. |
| 128 | All as per ser item No. 127 above, here in before but for One 5 Amp 5 pin socket outlet point on same board with other switches including earth wire complete all as specified and directed. |
| 129 | All as per ser item No. 127 here in before, but for One 5 Amp 5 pin socket outlet point on independent board complete all as specified and directed. |
| 130 | All as per ser item No. 127 here in before, but with 4.0 Sqmm (36/0.30mm) PVC copper stranded cable FRLS type for one 15 Amp 5 pin socket outlet point including PVC cable 4 Sqmm FRLS type copper stranded conductor as earth wire as specified & connected to common earth & earth terminals including boards for mounting purposes complete all as specified and directed. |
| 131 | S&F in replacement switch piano flush button 5 Amp single pole one way 230 volts white finish complete all as specified and directed. |
| 132 | S&F in replacement switch socket combination flush type 5 pin 5 Amp multipurpose 230 volts single pole one way suitable for 3 pin/2pin 5 Amp plug top white/ivory finish complete all as specified and directed. |
| 133 | S&F in replacement of switch socket combination multipurpose flush type 2 in 1 type (3 and 5 pin) 5/15 Amps, 230V, AC complete all as specified and directed. |
| 134 | S&F in replacement ceiling rose surface PVC 50mm dia 3 terminals including PVC mounting block white/ivory finish complete all as specified and directed. |
| 135 | S&F LED light fitting 1x 16W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. |
| 136 | S&F in replacement stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. complete all as specified and directed. |
| 137 | M&L of submain wiring with two single core PVC insulated unsheathed, multistranded flexible copper conductor 1100Volts grade, FRLS type, cables 6 Sqmm drawn through in and including rigid PVC heavy duty concealed conduits including 6 Sqmm 1100Volts grade, FRLS type, PVC insulated unsheathed multi stranded flexible copper conductor cable as continuous earth wire and connecting to common earth terminals complete all as specified and directed. Note:- (i) Two runs of cables and one run of continuous earthing cable drawn in conduit/ casing and caping will be measured as one length of sub main. (ii) PVC conduit / casing caping and its accessories is deem to be included in this item rates.(iii) Unit rate include for cutting chases for conduits and sinking for boxes and making good to wall, floors etc. |
| 138 | S&F distribution board sheet metal enclosure double door shutter type factory made fixed flush with wall or outside on wall surface suitable for mounting isolators & MCB's 240volts, 200 Amp rated bus bar with front openable cover suitable for SP & N 8 ways complete all as specified and directed. |
| 139 | S&F sheet metal enclosure with plug socket single pole and neutral with two pin and earth plug and with one MCB of 20 Amps (SP) complete all as specified and directed. |
| 140 | S&F in replacement of MCB SP 6-32 Amps/ 40 Amps, 230 Volts, 50 Hz with 10 KA, 'C' series complete all as specified and directed. |
| 141 | S&F in replacement of MCB SPN/DP upto 32 Amps, 230 Volts, 50 Hz with 10 KA, 'C' series complete all as specified and directed. |
| 142 | M&L in replacement of Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6 mm thickness buried directly in ground (earth pit not less than 2.25mtr deep below normal ground level) with top edge of earth plate not less than 1.5 mtr below normal ground level connected to and incl galvanised earth lead wire of 4.00mm dia by means of nuts & bolts, check nuts and washers of galvanised incl PCC pit of 1:2:4 type B-1, cover reinforced with XPM weight not less than 4 Kg/Sqm and 6mm dia bar handle, earth pit angle iron frame of size 25mm x 25mm, excavation and earth work in any type of soil, charcoal dust, salt, light grade GI watering pipe 20mm dia with funnel and wire -mesh and medium grade GI protection pipe of 15mm bore from top edge of earth plate upto main distribution board complete all to as shown in electrical plate No 3 of MES Sch 2009 (Part I) connected main switch board complete all as specified and directed. |
| 143 | S&F new exhaust fan, steel body AC single Phase. 230V of size 300mm sweep with, blades, and frame and louvers complete as per site requirement complete all as specified and directed. |
| 144 | S&F ceiling fan complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed. |
| 145 | M&L pipe galvanized, “Medium class”, including fittings 40 mm (1.5”) bore complete all as specified and directed. |
| 146 | M&L pipe galvanized, “Medium class”, including fittings 25 mm (1.0”) bore complete all as specified and directed. |
| 147 | S & F Gun metal gate valve with iron wheel head, screwed both ends for GI steel pipe of 40 mm bore sizes complete all as specified and directed. |
| 148 | S & F Gun metal gate valve with iron wheel head, screwed both ends for GI steel pipe of 25 mm bore sizes complete all as specified and directed. |
| 149 | Drilling and tapping of CI water line 20 mm/ 25mm for branch connection complete all as specified and directed. |
| 150 | Excavation in trenches not exceeding 1.5mtr wide and not exceeding 1.5 mtr in depth and getting out in soft/loose soil complete all as specified and directed. |
| 151 | Returning, filling in trenches, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick each layer in soft/loose soil complete all as specified and directed. |
| 152 | Removing excavated material/surplus soil and depositing where directed at a distance not exceeding 50mtr and depositing at a level not exceeding 1.5 mtr from starting point complete all as specified and directed. |
| 153 | Supply lay/spread in trenches, river sand, clean, including spreading, levelling, punning as in cushioning of cables complete all as specified and directed.Note :- Punned depth will be measured and paid. |
| 154 | Supply, lay in trenches fly ash bricks, old size for cable protection complete all as specified and directed. Note :- Bricks shall be laid in such a way that its length is perpendicular to the length of cable. |
| 155 | Supply, laying, connecting and testing LT UG cable FRLS XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade sheathed, multi stranded of 10 sqmm 3 core cross sectional area complete all as specified and directed. Note :-(i) Lugs and glands are deemed to be included in the rate quoted for laying of cable and to be used properly wherever required while connecting cables to the panel board. (ii) Earth work such as excavation, refilling, etc. shall be measured separately under relevant items. |
| 156 | S&F Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity 5 KVA complete all as specified and directed. |
| 157 | Supply and install hi wall split units indoor/outdoor complete with cordless remote control unit and with in built air ioniser and Plasma filter for better indoor air quality of capacity 1.5 Ton complete all as specified and directed. |
| 158 | NOTES :-1. The amount of schedule of credit shall be deducted from the total of this BOQ for arriving at contract sum. Please Enable Macros to View BoQ information |
