|
| 1 | Eartwork in excavation in foundation trenches in hard soil (vide classification of soil item-A) and disposal of excavation earth as obtained to a distace up to 50m including all lifts levlling ramming the foundation trenches removing roots trees surbs all complete as per approved designed Building specification and direction of E/I |
| 2 | filling in Foundation trenches and plinth in layers not exceeding 150mm thick well watered , rammed , fully fully compacted and fine dressed with earth obtained from excavation of foiundation trenches within a lead of 50M and lifts of 1.5m all complete as per building specification and direction of E/I. |
| 3 | filling in Foundation trenches and plinth in layers not exceeding 150mm thick well watered , rammed , fully fully compacted and fine dressed with earth obtained from excavation of foiundation trenches within a lead of 50M and lifts of 1.5m all complete as per building specification and direction of E/I. |
| 4 | Proving coarse clean sand in fillig in foundation trenches or in plinth includding ramming and watering in layes not exceeding 150mm thickwith all leads and lifts including cost of all materials, labours, royalty and taxes all complete as per approved designed Building specification and direction of E/I ( mode of Measurement of compacted volume). |
| 5 | Providing designation 75A one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I. |
| 6 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - all work upto plinth level |
| 7 | 1:3:6 (1 cement :3 Coarse sand ( zone-III ) :6 grade stone aggregate 20mm nominal size ) |
| 8 | Providing designation 75A brick work in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10 mm thick mortar joints, cost of screening materials, raking out joints to 15 mm depth curing, taxes and royalty all complete as per building specication and direction of E/I. |
| 9 | Providing designation 100A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9\\"x4.5\\"x3\\") in C.M (1:6) in superstructure with approved quality of clean coarse sand of F.M 2 to 2.5 including providing 10mm thick mortar joints , cost of screening materials, racking out joints to 15mm depth, curing taxes and royalty all complete as per specification and direction of E/I |
| 10 | Providing 112mm thick reinforced designation 100A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9\\"x4.5\\"x3\\") in C.M (1:4) in superstructure with approved quality of clean coarse sand of F.M 2 to 2.5 including providing 10mm thick mortar joints , cost of screening materials, racking out joints to 15mm depth, curing taxes and royalty all complete as per specification and direction of E/I |
| 11 | Providing and laying in position specified grade of reinforcement cement concrete of excluding the cost of centring and shuttering, finishing and reinforcement - all work upto plinth level |
| 12 | 1:1.5:3 (1 cement :1.5 Coarse sand ( zone-III ) : 3 grade stone aggregate 20mm nominal size ) |
| 13 | Reinforcement cement concrete work in walls (any thickness), including attached pilasters, buttersses, plinth and string cource, filleets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 Cement : 1.5 Coarce sand (zone-III) : 3 Graded stone aggregate 20 mm nominal size) |
| 14 | Reinforcement cement concrete work in beams, suspended floors, roofs having slope up to 15 degree landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircase and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 Cement : 1.5 Coarce sand (zone-III) : 3 Graded stone aggregate 20 mm nominal size) |
| 15 | Providing and laying damp proof course 50 mm thick with cement concrete 1:2:4 (1 Cement : 2 Coarce sand (zone-III) : 4 Graded stone aggregate 20 mm nominal size) |
| 16 | Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete |
| 17 | Foundations, footings, bases of columns, etc. for mass concrete |
| 18 | Suspended floors, roofs, landings, balconies and access platform |
| 19 | Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 20 | Columns, Pillars, Piers, Abutments, Posts and Struts |
| 21 | Stairs , ( excluding landings ) excepts spiral-cases |
| 22 | Providing Tor steel reinforcement as per approved design and drawing including carriage of Rods (straight or in coils) to work site, cutting, bending and binding with annealed wire with cost of wire, removal of rust, placing the rods in position complete as per building specification and direction of E/I. |
| 23 | 25% of total reinforcement taken for 8mm dia |
| 24 | 15% of total reinforcement taken for 10mm dia |
| 25 | 60% of total reinforcement taken for 12 to 25 mm dia |
| 26 | Supplying, fitting and fixing 35mm thick solid core decorative single leaf flus door shutter with both decorative vannered with block board core bended with high quality phenol formal dehydes synthetic resin of standard make with aluminium fitting such as hings, tower bolts , handle , cleats and sand blocks taxes all complete as per building specification and direction of E/I |
| 27 | Supplying, fitting and fixing 35mm thick solid core decorative single leaf flus door shutter with both decorative vannered with block board core bended with high quality phenol formal dehydes synthetic resin of standard make with aluminium fitting such as hings, tower bolts , handle , cleats and sand blocks taxes all complete as per building specification and direction of E/I |
| 28 | Providing and fixing pressed steel door frames conforming to IS: 4351,manufactured from commercial mild steel sheet of 1.60 mm thickness,including hinges, jamb, lock jamb,bead and if required angle thresholdof mild steel angle of section 50x25 mm, or base ties of 1.60 mm,pressed mild steel welded or rigidly fixed together by mechanical means,including M.S. pressed butt hinges 2.5 mm thick with mortar grade,lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre treatment of the surface as directed by Engineer-in-charge: Profile- B Fixing with adjustable lugs with split end tail to each jamb |
| 29 | Providing and fixing factory made P.V.C. door frame of size 50x47 mm with awall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size,complete as per manufacturer’s specification and direction of Engineer-in-Charge. |
| 30 | Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frames hall have a coat of steel primers of approved make and manufacture.M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. |
| 31 | Top, bottom and lock rails shall be provided both side of the panel.10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on theV as per direction of Engineer-in-charge, manufacturer's specification & drawing ( for W.C and bathroom door shutter) |
| 32 | Providing and fixing ISI marked aluminium butt hinges anodised (anodiccoating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etc. complete 125x75x4mm |
| 33 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodiccoating not less than grade AC 10 as per IS : 1868 ) transparent or dyedto required colour or shade, with necessary screws etc. complete : 150x10mm |
| 34 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete 250 x 16mm |
| 35 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P.brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : |
| 36 | For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately).......... Polyester powder coated aluminium(minimum thickness of polyester powder coating 50 micron) |
| 37 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): |
| 38 | With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) |
| 39 | Supplying, fitting and fixing M.S. grill made of 20x6mm M.S. flats as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth, hoisting carriage of grill to work site, hoisting as per building specification and direction of E/I. |
| 40 | Providing and fixing fan hook of 16mm dia M.S. bar 1 metre long bent to required size and shape, placed in position and fixed in R.C.C. slab beam at the time of casting all complete as per building specification and direction of E/I. |
| 41 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) |
| 42 | Supplying , fitting and fixing callapsible gate of approved size and make properly fabricated with vertical double channels 20x10x2mm , at 100mm . Centres and braced with M.S flat diagonals 20x3mm , with top and bottom rails of t iron 40x40x6mm as per building specification and direction of E/I. |
| 43 | providing and laying double charged verified floor tiles in different size ( thickness to be specified by the manufacturer ) with water absorption less than 0.08% and conforming to IS:15622/Iso 13006 of approved make in all colour and shades , laid on 20mm thick cement mortar 1:4 ( 1 cement : 4 coarse sand ) jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc. complete size of tiles 600 x600mm |
| 44 | Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement colours, shades,except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigments etc., complete |
| 45 | Providing and fixing 18mm thick gang saw cut mirror polishing ( premoulded & prepolished ) machin cut for kitchen platform and similar location of required size of approved shade , colour and texture laid over 20mm thick base of cement mortar 1:4 (1 Cement : 4 Coarse sand) , jointing with white cement mix with matching pigments epoxy touch ups, including rubbing, curing , moulding and polishing to edge to give high gloss finish etc. complete at all levels . Granite slab |
| 46 | Providing and laying 6mm thick precast white glazed tiles in wall over 12mm cement plaster (1:3) and jointed with grey cement sularry flush pointed with white cement including rubbing , polishing and cost of curing taxes and royalty all complete jobs as per specification and direction of E/I. |
| 47 | Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge. |
| 48 | Providing 12mm thick cement plaster (1:6) with clean coarse sand of F.M 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I |
| 49 | Providing 6 mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scafolding taxes and royalty all complete as per buildings specification and direction of E/I. |
| 50 | Providing 12 mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5 with 5% cico or any other approved water proofing compound including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I. |
| 51 | Providing 1.5mm cement punning including , curing carrage of water with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I |
| 52 | Supplying and fitting and fixing of C.I Cover 600x450mm ( weight 25 kg) all cost complete JSR Basic rate Rs 1470+14.95% for C.P- Pg39 |
| 53 | Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm brick honey comb shaft with bricks and S.W. drain pipe 100 mm 19.32.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 54 | Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete |
| 55 | Providing two coats of plastic synthetic enamel paint of approved shade and made over a coat of cement primer over new surface including prearing plasterd surface by rubbing smooth with pumic stone or fine sand paper , applying putty wherever required, scaffolding washing of floors and taxes all complete as per as per building specification and direction of E/I |
| 56 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 57 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.2 kg/10 Sqm |
| 58 | Providing french sprit polishing over new wooden surface to give desire texture and gloss with approved make and shade of ready mixed French polish including cleaning the surface after removing dirt, scales smokes , greses and sand papering including cost of ,scaffolding and taxes all complete as per as per building specification and direction of E/I |
| 59 | Providing two coats of synthetic enamel paint of approved shade and made over steel surface including cleaning the surface thoroughly including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I |
| 60 | Providing 250mm. wide brick drain in cement mortar (1:6) with av. 250mm. clear depth and 250mm. apron including cost of earthwork involved with 75 mm. ~ cement concrete (1:4:8) over one brick designation 75A flat soling in proper grade and slope at the base, the drain duly plastered in C.M.(1:3) with punning over exposed surface all complete as per building specification and direction of E/l. |
| 61 | Making plinth protection 50mm thick of cement concrete (1:3:6) over 75 mm thick bed of dry brick ballast 40 mm nominal size of well rammed and consolidated and grouted with fine sand including finishing the top smooth |
| 62 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes 110 mm diameter |
| 63 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion |
| 64 | Bend 87.5° 110 x110 x 110mm |
| 65 | Shoe (Plain) 110mm bend |
| 66 | Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams. |
| 67 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.110 mm |
| 68 | Providing & injecting chemical emulsion for pre - construction anti-tremite and creating a chemical barrier under and all around the column pits , wall trenches , basement excavation , top surface of plinth filling junctions of wall and floor along the external perimeter of building with approved chemical as per IS code all complete as per building specification and direction of E/l. |
| 69 | Providing and fixing factory made precast RCC perforated drain covers,having concrete of strength not less than M-25, of size 1000 x 450x50 mm, reinforced with 8 mm dia four nos longitudinal & 9 nos cross sectional T.M.T. hoop bars, including providing 50 mm dia perforations @ 100 to 125mm C/C , including providing edge binding with M.Sflats of size 50 mm x 1.6 mm complete, all as per direction of Engineer- in-charge |
| 70 | Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. |
| 71 | Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. |
| 72 | Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. |
| 73 | Cost of drilling 200mm x 165mm x125 mtr deep bore well in all kinds of soil and rock in rural of other area for installation of pump set with Hydrolic DTH rig machine all complete including supplying all materials, tools, drilling rig, air compressor and equipment as well as fuel lubricants and cost of transporting charge of rig machine and other vehicle up to site of the work including cost of flushin charges Geological investigation etc all complete. |
| 74 | Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I) 150 mm dia |
| 75 | Supplying , fitting and fixing 125mm dia UPVC pipe of approved quality and make- basic rate +10% CP |
| 76 | Suppling , fitting and fixing viterous white glazed earthen ware I.W.C of pary hindustan or any other ISS approved make with 100mm HCI p trap 15 litre CI pull and let go flushing cistern of name or other Iss equivelent make complete with all fitting CI or CC brackets 32mm alkethene /PVC telescopic flush pipe about 2m long with one brass coupling and clamp GI chain and pull including supplying and fixing a pair of vitrus with glazed earthen ware foolrest to be fixed in floor 15mm CI body brass spindle stop cock of weigh not less than 50grams 15mm PVC connection pipe 450mm long and coat of red oxide primer etc all complete as per specification and direction of E/I (a) 580mm long with 12.5 litre low level PVC cistern |
| 77 | Suppling , fitting and fixing 40mm high viterous white glazed earthen ware E.W.C with \\"p\\" trap of pary hindustan or any other ISS approved make including supplying & fixing 15 litre CI mosquito proof low down flushing cistern of approved make with complete fitting with CI handle and R.S or bracket with telescopic flush pipe with brass coupling and plumber joints spindle stop cock of approved quality weigh not less than 450 grams 15 mm PVC alkathene pipe 45 cm long with brass coupling at both ends and white / black plastic solid state seal and lead of commander / cuckoo or other I.S.S make with hings or screw etc. painting pipe and cistern etc with 2 coats of approved paint over a coat of read oxide primer etc all complete as per specification and direction of E/I (b) 12.5 litr. low level PVC cistern |
| 78 | Suppling , fitting and fixing viterous white glazed earthen ware wash hand basin of pany or Hindustan any other ISS approved make supported on painted CI or R.S bracket 32mm C.I brass 15 mm dia C.I body brass spindle stop cock of approved quality weigh not less than 350 grams 32 mm PVC waste pipe 750 mm long with brass coupling at one ends and making plumber joints etc. all complete as per specification and direction of E/I Flat back or standing corner ( 600x350 mm) |
| 79 | Suppling , fitting and fixing flat black or angular lipped front viterous white glazed earthen ware urinal of Hindustan \\"pary\\" or any other ISS approved make with 5 litre capacity CI automatic flushing cistern of reliance for any other ISS approved make with all fitting with CI or R.S bracket standard size of GI flush pipe with fitting clamps 15 mm C.I body brass spindle stop cock of approved quality weigh not less than 400 grams 15 mm PVC alkathene pipe 450 mm long with brass coupling at both ends and doing plumber points including painting of exposed part with two approved paint over a priming coat of read oxide cutting wall and floor making good the same etc. all complete as per specification and direction of E/I Flat back or standing corner ( 600x350 mm) |
| 80 | Providing and fixing Gun Metal full way valve of approved quality, all complete, as per specification and direction of E/I |
| 81 | 20 mm dia |
| 82 | 25 mm dia |
| 83 | 32 mm dia |
| 84 | 40 mm dia |
| 85 | Providing and fixing brass stop cock of approved quality all complete, as per specification and direction of E/I |
| 86 | Cutting drain width wise above GL for laying PVc pipe and restoring brick work in cement mortar (1:4) 12mm cement plaster in cm ( 1:4) with neat cement punning as per specification and direction of E/I ( PVC 110 mm) |
| 87 | Making hole in wall for laying PVC pipe and restoring the same all complete ( PVC pipe 110 mm dia) |
| 88 | Supplying all tools and labour and cutting chajja cornice for laying PVC pipe and making good the same as per specification and direction of E/I ( 110mm dia PVc pipe) |
| 89 | Supplying , fitting and fixing bathroom fitting of approved make and as per IS specification and direction of E/I ( all rate have been adopted from the basic rate from SOR + 30% for labour and contractor profit) |
| 90 | Pillar cock ( long neck ) ( basic rate 806.5 + 10% for C.p & laying charge) |
| 91 | Bib cock ( long thread) ( basic rate 728.15 + 10% for C.p & laying charge) |
| 92 | glass shelf ( long thread) ( basic rate 683.55 + 10% for C.p & laying charge) |
| 93 | 32mm dia PVC waste pipe 750 mm long with coupling ( basic rate Rs. 62.40 + 10% for C.P & laying charge |
| 94 | 15mm C.P nipple with coupling ( basic rate Rs. 87.2+ + 10% for C.P & laying charge |
| 95 | Steel jali - 100mm dia ( basic rate 48.20 + 10% for C.p & laying charge) |
| 96 | Solvent cement ( basic rate 168 + 10% for C.p & laying charge) |
| 97 | Suppling , fitting and fixing mirror of 6mm thick plate glass bevelled edge mirrors including C.P brass revolving fitting 3mm ply wood board and c.p hings to fix with mirror 600x450mm |
| 98 | Suppling , fitting and fixing mirror of 6mm thick plate glass bevelled edge mirrors including C.P brass revolving fitting 3mm ply wood board and c.p hings to fix with mirror 600x450mm |
| 99 | Providing and fixing 15mm dia and 45cm long PVC connection pipe with heavy quality brass coupling at both ends etc all complete, as per specification and direction of E/I |
| 100 | supplying , materials and labour for constructing inspection Chamber of designation class 75B bricks size 750mm deep , 600x450mm internal dimension having 250mm wall thickness , in cement mortar 1:6 (1 cement :6coarse sand) including 12mm cement plaster (1:4) with punning on inside and cement plaster (1:6) with 600x475mm G.I cover with frame ( weight not less than 35 kg ) along with earth work in excavation and 80mm thick PCC (1:3:6) in foundation and refilling all complete, as per specification and direction of E/I |
| 101 | Construction of septic tank - detailed estimate enclosed- 50 user ( without soakpit) |
| 102 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 15mm dia nominal bore of approved brand C.P fitting |
| 103 | Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour.15 mm size of 12\\" BSP thread 70mm length 30mm breadth , weighing not less than 18 gms of approved make |
| 104 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc |
| 105 | 20 mm nominal bore |
| 106 | 25 mm nominal bore |
| 107 | 32 mm nominal bore |
| 108 | External Work- 40 mm nominal bore |
| 109 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes 110 mm diameter |
| 110 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. |
| 111 | Bend 87.5°(110x110x110mm) |
| 112 | Single Plain 110mm shoe |
| 113 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 114 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. |
| 115 | Cutting Chajja or concrete for laying PVC pipe and restoring the same with R.C.C ( 1:2:4) brick work in cement mortar (1:4) and cement plaster 1;4 as per specification and direction of E/I |
| 116 | Making hole in wall for laying PVC pipe and restoring the same after laying (b) 250mm thick wall |
| 117 | Supplying and fixing PVC fitting of approver make confirming to IS 1729 including supplying nail and bobbies , fixing solution including earth work or masnory work cutting and remaking and providing as the case may be all complete as per specification and direction of E/I |
| 118 | PVC cowl- 100 mm dia |
| 119 | Floor trap- 100 mm dia |
| 120 | Lubricant |
| 121 | Door piece |
| 122 | Cost of drilling 200mm x 165mm x125 mtr deep bore well in all kinds of soil and rock in rural of other area for installation of pump set with Hydrolic DTH rig machine all complete including supplying all materials, tools, drilling rig, air compressor and equipment as well as fuel lubricants and cost of transporting charge of rig machine and other vehicle up to site of the work including cost of flushin charges Geological investigation etc all complete. |
| 123 | (a) Up to 50 mtr. Depth bellow G.L |
| 124 | (b) Above 51-125 mtr |
| 125 | (b) Above 125 mtr |
| 126 | Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. |
| 127 | Gravel packing in tubewell construction in accordance with IS: 4097,including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge. |
| 128 | Development of tube well in accordance with IS : 2800 (part I) and IS:11189, to establish maximum rate of usable water yield without sand ontent (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by \\"V\\" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc.,all as per requirement and direction of Engineer-in-charge. |
| 129 | Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of 200 mm dia |
| 130 | Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete 200 mm clamp |
| 131 | Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I) 200 mm dia |
| 132 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply plain & brass threaded fittings This includes jointing with one step CPVC solvent cement, trenching,joints complete as per direction of Engineer in Charge |
| 133 | 50 mm nominal dia Pipes |
| 134 | Supplying submersible pump set confirming to IS:8034 and motors confirming to IS:9283 pump shall be suitable for various delevery head and discharge with stainless steel pump shaft and polypropylene/ noyl impeller , motor suitable for working on 415+10% , 3PH , 50Hz, AC supply with cable guard , thrust carbon / fiber bearing to withstand entire hydraulic thrust , water proff winding shall be provided . the pump set shall be suitable for direct couplings, pump shall have suitable outlet as per manufacture design . anti thrust strem lined non return valve shall be provided with pump . 3 mtr. submersible copper conductor cable in single/double run shall be provided with each pump |
| 135 | Point Wiring in PVC Conduit , with modular type switch -wiring for light point/ fan point/exhaust fan point / call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, with modular type switch suitable size of GI box as required |
| 136 | S/F power light plug point with Modular type accessories :-Supplying and fixing suitable size G.I box with modular plate in front of surface or in recess including providing and fixing 3 pin 15/16 amps socket out let and 15/16 amps modular type switch in connection painting etc as required. |
| 137 | S/F power light plug point with Modular type accessories :-Supplying and fixing suitable size G.I box with modular plate in front of surface or in recess including providing and fixing 6 pin 15/16 amps socket out let and 15/16 amps modular type switch in connection painting etc as required. |
| 138 | Wiring for circuit / sub main wiring alongwith earth wire with the following sizes of PVC insulated, copper conductor , single core cable in surface/ recessed PVC coduit as required. |
| 139 | 2X1.5 sq mm+1X1.5 sq mm eart wire |
| 140 | 2X2.5 sq mm+1X2.5 sq mm eart wire |
| 141 | 2X4 sq mm+1X4sq mm eart wire |
| 142 | 4X6 sq mm+2X6sq mm eart wire |
| 143 | S/F TP MCB DB :-Supplying and fixing of following way three pole & neutral, sheet steel , MCB distribution board 415 volts, on surface /recess , complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections,phosphatized and powder pointed including earthing etc. as reqd.( Without MCB / RCCB/ ISOLATOR ( ALL TP MCB DB shall be as per IS: 8623) |
| 144 | 4 way ( 4+12 way) double door |
| 145 | S/F \\"C\\" series, S.P MCB :- Supplying & fixing 240 volts \\"C\\" series miniature circuit breaker suitable for inductive loads of following pole in the existing MCB DB with connection testing and commissioning etc. |
| 146 | 6/32 A single pole |
| 147 | 6/32 A TPN MCB |
| 148 | S/F 3 pin, 5amp. Ceiling rose on the existing junction box / wooden block including connection etc.as reqd. |
| 149 | S/F Modular type fan regulator :-Supplying and fixing stepped type fan regulator on the existing modular plate switch box including connection but excluding modular plate etc as required. |
| 150 | ITC Exhauts fan upto 450mm sweep : installation of exhaust fan upto 450mm sweep in the existing opening , including making the hole to cut the size of the above fan , making good the damage, including connection , testing commissioning etc as required |
| 151 | S/F brass battan / angle holder including connection etc.as reqd. |
| 152 | S.I.T.C of following rating surface mounted LED tube light fitting suitable for 230v , 50Hz , single phase supply etc. complete as required - 20/22 W. LED tube light |
| 153 | Bulk head fitting with 9/10 Watt CFL/LED |
| 154 | Supplying, 15/16 Watt LED bulb of approved make |
| 155 | Supplying Exhaust fan of 12\\" (300mm) of approved make |
| 156 | Supplying installation and commissiong of following size celling fan 3 blades confirming to IS : 374 : 2019 including wiring the down rods of standard length ( upto 30cm) with 1.5 sq.mm FR PVC insulated copper wire suitable for 230V , 50Hz, single phase supply etc. complete required - 1400mm (56\\") ceiling fan |
| 157 | S.I.T.C of following rating LED street lighting luminarie die cast housing and toughened glass cover (IP-66 portion ) in existing pole / pipe for supply voltage 100-270v, AC , 50Hz Luminaire shall be confirm to IS: 10322 part- 5/Section 3 and shall be complete with all necessary accessories as required - 60W LED street light |
| 158 | S.I.T.C of following rating recess / surface mounted LED round/square shape down light luminaire with pressure die cast housing for single phase supply voltage luminaire shall be confirm IS : 10322 part-5/section 2 of IEC :62722 with all necessary accessories as required 15/16W LED round down light - as CL |
| 159 | GI Eart Pipe Electrode : Earthing with G.I earth pipe 4.5 mtr long , 40mm dia including accessories and providing masnory enclosure with cover plate having locking arrangement and watering pipe etc with charcol and salt complete as required |
| 160 | Supplying and laying 25mm x5mm G.I strip at 0.50 metre below ground as strip earth electrode including connection / terminating G.I nut , Bolts, spring, washers as required ( jointing shall be done by overlapping and with 2seat of G.I nut bolt & spring washer spaced at 50mm) |
| 161 | Providing and fixing 25mm x5mm G.I strip on surface or in recess for connection etc. as required |
| 162 | Providing and laying 101 Kv grade almunium armoured cable as per IS 1554 ( part I) heavy duty all cost complete including cost of brass copression gland , cable jointing and end termination as per specification and direction of E/I |
| 163 | 3.5 core , 35 sq.mm |
| 164 | Carrage of materials |
| 165 | Brick |
| 166 | Coarse sand |
| 167 | Stone chips |
| 168 | Stone Metal |
| 169 | Earth |
| 170 | G.S.T @ 18% |
| 171 | LABOUR CESS @ 1% Please Enable Macros to View BoQ information |
