Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | DEV. OF NRO- BALARAMPUR- P&M |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30 cm in depth, 1.5m in width as well as 10 sqm on plan) including taking out and disposal of excavated earth within or outside site to unobjectionable place and lift upto 1.5m, as directed by Engineer-in-charge. Disposed earth to be levelled and neatly dressed. Extra for levelling & neatly dressing of disposed soil completely to be paid separately as per item no. MPLCN00600 |
| 3 | EXC. OVER AREAS IN ALL KINDS OF SOIL |
| 4 | EXC. OVER AREAS IN ORDINARY ROCK |
| 5 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil & disposal of surplus excavated soil as directed, within or outside the site at an unobjectionable place. |
| 6 | EXC. IN ALL KINDS OF SOIL |
| 7 | EXC. IN ORDINARY ROCK |
| 8 | Excavating trenches of required width for pipes, cables etc including excavation for sockets & dressing of sides, ramming of bottoms,depth upto 1.5m including taking out excavated soil & then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc. and disposing surplus excavated soil as directed, within or outside site at unobjectionable place in all kinds of soil |
| 9 | EXTRA DEPTH 1.5M< 3M UPTO 80MM DIA |
| 10 | FILLING AVAILABLE EARTH |
| 11 | Supplying and filling in plinth with sand within specified grading zone of fine aggregates specified in table 3.1, clause 3.1.3 of attached specifications under floors, etc. in layers not exceeding 20cm in depth, each deposited layer to be compacted by ramming including watering, consolidating and dressing complete. |
| 12 | SUPPLY FILLING LOCAL SAND ZONE IV |
| 13 | Providing and laying in position cement concrete of specified grade excluding cost of centering & shuttering. All work up to plinth level: |
| 14 | 1 CEMENT:2 COARSE SAND:4 AGG. 20MM |
| 15 | 1 CEMENT:3 COARSE SAND:6 AGG. 20MM |
| 16 | Centering and shuttering including strutting, propping etc. and removal of form work for: |
| 17 | CENT.& SHUT.FOR PCC-FOUND,FOOTING ETC |
| 18 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level |
| 19 | RCC 1:1½:3 UP TO PLINTH LEVEL W/O C&S |
| 20 | Centering and shuttering including strutting, propping etc. and removal of form for : |
| 21 | CENT.& SHUTT. FOR RCC COLUMNS |
| 22 | Supply of Steel reinforcement for R.C.C. including straightening, cutting, bending, placing in position and binding all complete at all levels |
| 23 | TMT BARS FE- 500 GRADE |
| 24 | Providing and laying Brick work with common burnt clay F.P.S (non Modular) bricks of class designation 7.5 in foundation & plinth |
| 25 | BRICK WORK IN CM 1:6 IN FOUNDN & PLINTH |
| 26 | Providing and fixing 18mm thick gang saw cut mirror polished premoulded and prepolished, machine cut for kitchen platforms, vanity counters, sills, facias, Pump Island & similar locations of required size, approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding & polishing to edge to give high gloss finish etc. complete at all levels. |
| 27 | POLISHED GRANITE - KITCH.CUNTR<0.50SM |
| 28 | POLISHED GRANITE - KITCH.CUNTR>0.50SM |
| 29 | Extra for providing edge moulding to 18mm Granite/ marble stone counters,Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in- Charge. |
| 30 | EXTRA FOR EDGE MOULDING TO GRANITE WORK |
| 31 | EXTRA FOR OPENING FOR WASH BASIN ETC. |
| 32 | Structural steel work riveted, bolted or |
| 33 | STR.STEEL IN BUILT UP SECTION |
| 34 | Steel work in built up tubular (round,square or rectangular hollow tubes etc) trusses etc. including cutting,hoisting fixing in position and applying a priming coat of approved steel primer, including welded and bolted with special shaped washers etc. complete. |
| 35 | HOT FINISHED WELDED TYPE TUBULAR TRUSS |
| 36 | Providing and laying cement plaster on surfaces with fine sand including curing etc. |
| 37 | 12MM CEMENT PLASTER,1:4 WITH FINE SAND |
| 38 | ACRYLIC SMOOTH EXTERIOR PAINT |
| 39 | DELUXE MULTISURFACE PAINT-STEEL SURFACE |
| 40 | SYNTHETIC ENAMEL PAINT |
| 41 | Providing and fixing B class G.I. pipes complete with G.I. fittings including trenching and refilling etc for WATER and AIR, External work |
| 42 | 15 MM DIA. NOMINAL BORE |
| 43 | 20 MM DIA. NOMINAL BORE |
| 44 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : |
| 45 | 15MM BRASS BALL VALVES-PLASTIC FLOAT |
| 46 | S/L OF 50 MM DIA SINGLE WALL FLEXIBLE PI |
| 47 | S/L OF 80 MM DIA SINGLE WALL FLEXIBLE PI |
| 48 | Installation of supplied 20 KL Tank as per specified drawings as per work description but excluding all works of kerb wall and Gasket for manhole including painting / doping with Shalimastic HD as applicable as per specifications complete. RCC works wherever mentioned shall be of grade M20 |
| 49 | 20KL TANK IN B.M. PIT, RCC STRIPRAFT U/D |
| 50 | Supply, fabrication, laying and testing of MS, BLACK, ERW, threaded pipes, heavy class conforming to IS 1239, PART I as per IOCL specifications including pipeline fittings like bends, tee etc as required and as directed for Underground pipeline with doping |
| 51 | S/L U/G MS THREADED 50 MM DIA PIPE |
| 52 | Supply, fabrication, laying and testing of MS, BLACK, ERW, threaded pipes, heavy class conforming to IS 1239, PART I as per IOCL Specifications including pipeline fittings like bends, tee etc as required and as directed for Above Ground pipeline including surface preparation according to standard SSPC ST2 and painting with 2 coats of red oxide zinc phosphate primer and 2 coats of Synthetic enamel / aluminium finish paint as per IOCL specifications |
| 53 | S/L A/G MS THREADED 50 MM DIA PIPE |
| 54 | Supply, fabrication, laying and testing of MS black, ERW welded, pipes, heavy class conforming to IS 1239, PART I as per IOCL specifications including pipeline fittings like bends, tee etc as required and as directed for Underground pipeline with doping |
| 55 | S/L U/G MS WELDED 80 MM DIA PIPE |
| 56 | S/L U/G MS WELDED 50 MM DIA PIPE |
| 57 | Fabrication, Installation, Welding & testing of Corporation supplied MS or GI pipes for Underground pipeline with doping. Pipeline fittings 80 mm dia and below is to be supplied by party. |
| 58 | LAYING SUPPLIED 50 MM DIA U/G PIPE |
| 59 | Supply & welding slip-on flanges conforming to IS2062 GrA, ANSI B16.5, Class#150 with 3 runs of weld outside and one run of weld inside the flanges as per specifications and standard Drg.enclosed herein |
| 60 | S/W SLIPON FLANGES OF 100 MM DIA. |
| 61 | S/W SLIPON FLANGES OF 50 MM DIA. |
| 62 | Making flanged joints between flanges slip on, blind and flange etc. including providing/supplying 3 mm thick permanite oil gasket, nuts, bolts, bonding with 3 mm dia copper wire etc.complete as per IOCL specifications. |
| 63 | MAKING SLIPON / BLIND FLANGE JOINT 50MM |
| 64 | Supplying and installation of the following threaded coupling |
| 65 | 80 MM DIA AL. CAMLOCK COUPLING - MALE |
| 66 | Supply and installation of ‘U’ type CS bend on the vent pipes including painting as per specifications and supplying and brazing wire mesh of 11 mesh per linear centi-meter of non-corrosive metal in two layers on both ends. |
| 67 | S/I U TYPE 50MM CS BEND ON VENT PIPES |
| 68 | Providing stainless steel wire mesh 32 SWG, 11 mesh per linear cm of of non corrosive metal in two layers on existing vent hoods ‘U’ type (on both ends) including brazing, etc. complete |
| 69 | P/F SS WIRE MESH 32SWG ON 50MM V. HOODS |
| 70 | Supply and installation of screwed type gun metal valves as per IOC specifications: Ball Valve |
| 71 | S/I SCREWED GM BALL VALVE 80MM DIA |
| 72 | S/I SCREWED GM BALL VALVE 50MM DIA |
| 73 | Installation of supplied Multi Product Pumps / Dispensers on pump island as per manufacturers installation manual, drawings, including supplying, providing necessary frame of ISMC 100, foundation bolts, supplying and filling required quantity of dry sand in pit(s) below the pump |
| 74 | 2 PRODUCT - 4 NOZZLE MPP/MPD |
| 75 | Air compressor Supply and installation of horizontal air compressor assembly with delivery pressure of 12 kg/sq cm equipped with pressure gauge, non- return/safety/drain/delivery valves, automatic cut-off switch and suitable electrical connections & all standard accessories, including civil works: |
| 76 | S/I OF 3 HP (160-220 LITRES) COMPRESSOR |
| 77 | S/I DIGITAL TYRE INFLATOR |
| 78 | Transportation of equipment from one location to another location including enroute all taxes, levies and unloading/loading by a suitable vehicle exclusively for this purpose (In case of tank same shall be loaded by the tank fabrication contractor) |
| 79 | TRANSPTN OF 15/20 KL TANK : 0 - 30 KM |
| 80 | TPT/KM OF 15/20KL TANK: EXTRA > 30KM |
| 81 | T-MONO/DUO/AIRCOMP/STP/PUMPS:3-6, <30KM |
| 82 | T/KM-MONO/DUO/AIRCOMP/STP/PUMPS:3-6, >30 |
| 83 | Loading/unloading charges for 10/15/20/ 50/70 KL tanks. |
| 84 | LOADING, UNLOADING 15 /20 KL TANK |
| 85 | S & F FRESH WATER IN U/G TANK |
| 86 | REMOVING WATER FROM U/G TANK |
| 87 | S/F 2\\" PV VALVES |
| 88 | INSTALLATION OF STP |
| 89 | CABLING AND ALLIED WORKS - ARMOURED CABLES Supply & laying of XLPE insulated PVC sheathed aluminium/copper conductor, 1.1 kV grade armoured cable conforming to IS:7098, as per approved make in ground/ trench/surface/pipe, etc. whereever required as per direction of Engineer In-charge. Note: The rate of Installation should be inclusive of Cable clamps, tags Saddles, Consumables etc. Trays/pipes, trenches, fabricated tray supports etc will be covered & paid in Separate Items |
| 90 | S&L 3X2.5 SQMM,1.1KV FRLS CU ARMD CABLE |
| 91 | S&L 4X2.5 SQMM,1.1KV FRLS CU ARMD CABLE |
| 92 | Re-laying corporation supplied cable complete as per specification |
| 93 | RELAYNG IOC SUPPLD 1.5-10SQMM XLPE CABLE |
| 94 | RELA. IOC SUP. 4 -10SQMM XLPE/AYFY CABLE |
| 95 | RELA. IOC SUP.16 -35SQMM XLPE/AYFY CABLE |
| 96 | RELA. IOC SUP.50 -70SQMM XLPE/AYFY CABLE |
| 97 | RELA. IOC SUP.120SQMM XLPE/AYFY CABLE |
| 98 | SUPPLY AND LAYING OF FLAT CABLES |
| 99 | S&L 3X2.5SQMM CU FLAT CABLE -SUBM PUMP |
| 100 | S&L 3X4SQMM CU FLAT CABLE -SUBM PUMP |
| 101 | CABLE TERMINATION GLANDS NON-FLP HEAVY DUTY DOUBLE COMPRESSION Cable Termination (NON FLP): Providing termination of 1.1 kV grade armoured cable for the following sizes including supply of NON FLP heavy duty Double Compresson cable glands, crimping type lugs and allied jointing materials, etc. all complete as per specification and direction of Engineer In-charge. Glands and lugs shall be of approved make. Copper lugs for copper cables and aluminium lugs for aluminium cables shall be used. |
| 102 | CABLE TERM,NON FLP DC GLAND 3X2.5SQMM |
| 103 | CABLE TERM,NON FLP DC GLAND 4X2.5SQMM |
| 104 | CABLE JOINTING Cable Jointing : Providing straight through joint of following 1.1 KV grade XLPE insulated armoured cable with M-Seal make jointing kit, and other jointing material, etc. all complete including supply of all materials as per specification & direction of Engineer In-charge. |
| 105 | CABLE JOINTING KIT FOR 3X2.5SQMM |
| 106 | CABLE JOINTING KIT FOR 4X2.5SQMM |
| 107 | CABLE JOINTING KIT FOR 3.5X25SQMM |
| 108 | CABLE JOINTING KIT FOR 3.5X35SQMM |
| 109 | CABLE JOINTING KIT FOR 3.5X50SQMM |
| 110 | CABLE JOINTING KIT FOR 3.5X70SQMM |
| 111 | CABLE ROUTE MARKER WITH 100X100X5MM |
| 112 | Supply & laying of Automation Signal cable-Stranded (Class2) Annealed Bare Copper Conductor, Extruded PVC type C Insulated, 2 Cores Twisted to form a pair, each shielded with Aluminium backed Mylar Tape along withATC Drain Wire,multipairs laid up &Overall Shielded with Aluminium backed Mylar Tape along with ATC (Annealed Tinned Copper) Drain Wire and Extruded PVC Type ST-2 Inner Sheathed, Galvanised Steel Round Wire Armoured and Overall Extruded FRLS PVC Type ST-2 Outer Sheathed Instrumentation/Signal Cables conforming to BS 5308-2 & IS 1554-1 |
| 113 | AUTOMATION SIGNAL CABLE - 4PX0.5SQM |
| 114 | CHEMICAL EARTHING - CU BONDED ROD |
| 115 | Supply & drawing/laying, jointing, connecting, testing and commissioning of earth strip/copper strip/GI wire for earthing and lightning protection under or aboveground complete as per specification for the following : |
| 116 | EARTHING WITH 50 X 10MM G.I. STRIP |
| 117 | EARTHING WITH 32 X 6 MM G.I.STRIP |
| 118 | EARTHING WITH 25 X 3 MM GI STRIP |
| 119 | 16SQMM CUCABLE INCL.CROCDILCLIPIN LT PNL |
| 120 | Supplying & Fixing of following items for electrical safety in switch rooms/DG rooms etc |
| 121 | S&F RUBBER MAT 33KV GRADE (2MX1M SIZE) |
| 122 | S&F 6MM THICK CHEQUERED PLATE |
| 123 | S&F SHOCK TREATMENT CHART |
| 124 | S&F 11 KV GRADE HAND GLOVES, ISI MARK |
| 125 | PANEL BOARDS AND DISTRIBUTION BOARDS Supply, installation, testing and commissioning of cubicle type power and motor control centre panel fabricated out of 14 SWG sheet steel undergone 7 tank process,dust & vermin proof, floor mounting type, suitable for indoor use having cable entry from the bottom and having following specific components complete, control wiring etc. as per enclosed standard drawing. Any other components/hardware required to complete the panels but not mentioned here shall also be provided. Note: Both incomers should have mechanical interlock for proper & safe operation. The MCCB used for incomer feeder shall have short circuit, overload and earthfault protection and also shunt coil for ESD operation. The Bus Bar support shall be DMC/ SMC/Epoxy moulded. All equipment/components shall be mounted logically to have free access for maintenance, tightening of connections & visual inspection. All the metering equipment shall be Digital & mounted on the panel and size of meter shall be 96 mm x 96 mm. The Bus Bar shall be provided with heat shrunk PVC sleeves & all power terminals shall be stud type with properly shrouding to avoid accidental contact. Neoprene type gasket shall be provided at the doorof the panel. The enclosure of the Panel shall have IP52 degree of protection. 2 Nos earth terminal shall be provided at the Panel frame with extension link for earthing connections. Painting:The under surface shall be prepared by applying a coat of phosphate paint and coat of yellow zinc chromate primer. The under surface shall be made free from all imperfections before undertaking the finishing coat. After preparation of the under surface, the switchboard shall be spray painted with two coats of epoxy based final paint or shall be powder coated. Colour shade of final paint shall be RAL 7032. |
| 126 | PANEL & DISTRIB. BOARDS - MEDIUM RO |
| 127 | Supplying and fixing of following MCBs with necessery inter connections on existing DB, Panel board etc. |
| 128 | S&F MCB+ELCB UPTO 32A DP MCB |
| 129 | Supply and installation of MCB distribution board having Double door complete with tinned cu bus bar, neutral bus bar, earth bar, din bar, interconnection, earthing etc. without incoming isolator and MCBs |
| 130 | S&F MCB DB WITH 4 WAY (4+12) TPN |
| 131 | S & I OF ESD SYSTEM |
| 132 | Supplying and fixing 12 volt Charged LA battery of approved make for Electronic dispensing pumps including giving necessery electrical connection for the following AH ratings. |
| 133 | 12V , 7AH CHARGED LA BATTERY WITH STAND |
| 134 | CONSTANT VOLTAGE TRANSFORMER Supplying, installation, testing and commissioning of single phase, air cooled constant voltage transformer of approved make having input voltage range of 180-260V and output voltage of 220/230V with sine wave output wave form and having automatic current limiting and short circuit protection including all accessories complete (for displays) for the following VA ratings. |
| 135 | S/I SINGLE PAHSE AIRCOOLED 500VA CVT |
| 136 | SINGLE SERVO VOLTAGE STABILISER Supply and fixing of 230V, Single phase, AC Servo voltage stabilizer of approved makes,(Range - 180 - 250 minimum) shall be provided for Individual dispensing pump as per IE Regulation and as per specification |
| 137 | S/I SINGLE PHASE SERVO STABILISER-5 KVA |
| 138 | Supply, fitting, fixing of arm bracket, tubular type, 38mm/50mm dia on pole including painting, all complete. |
| 139 | S&E ARM \\" Y BRACKET 38/50MM DIA. ON POLE |
| 140 | Supplying & drawing inside the poles 3 core 2.5 sq.mm PVC insulated flexible copper conductor, fixing of junction box at the pole base (excluding supply of JB), making all connections on both ends, all complete as per specification and direction of Engineer In-charge. |
| 141 | S&D 3CX2.5SQMM PVC CU WIRE IN L POLE |
| 142 | OCTAGONAL POLES Supply & Fixing of Octagonal Poles of following type (Civil job shall be paid separatly) : |
| 143 | S&E 7M HIGH GALVANISED OCTAGONAL POLE |
| 144 | YARD LIGHTS: 100W WITH IP66 PROTECTION |
| 145 | DISMANTLING Dismantling of following electrical fittings / fixtures with all leads and lifts. |
| 146 | DISMENTLING ELE CABLE OF ALL SIZE AG/UG |
| 147 | PANEL BOARD STICKERING WORK |
| 148 | PANEL BOARD MARKING |
| 149 | PREPARATION OF SLD - ELECTRICAL LAYOUT |
| 150 | PREPARATION OF SLD - EARTHING LAYOUT |
| 151 | Supply and Installation of 16 SWG MS/GI powder coated weather proof Earthing Box of following size with door and locking arrangement with lock and key. Box to be mounted on ISA 40x40x5 (Painted with black synthetic enamel paint) frame having 2 legs of length 800 mm (500 mm above ground and 300 mm below ground which is to be grouted with PCC 1:2:4). Bottom of box should have opening for incoming earth GI strips all complete, as per specification and direction of Engineer-in-charge. Note: EARTHING BOX in RED should be boldly written over the box. The box should have a hood at the top extending outwards such that no water should seep through inside the box during rainy season to avoid rusting. |
| 152 | Supply and Installation of 16 SWG MS/GI powder coated weather proof Earthing Box |
| 153 | Earthing Pit Tag |
| 154 | Designing, fabricating, testing, installing Aluminium Composite Panel Claddin |
| 155 | DEV. OF NRO- BALARAMPUR- NON-P&M |
| 156 | SURFACE EXCAVATION |
| 157 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30 cm in depth, 1.5m in width as well as 10 sqm on plan) including taking out and disposal of excavated earth within or outside site to unobjectionable place and lift upto 1.5m, as directed by Engineer-in-charge. Disposed earth to be levelled and neatly dressed. Extra for levelling & neatly dressing of disposed soil completely to be paid separately as per item no. MPLCN00600 |
| 158 | EXC. OVER AREAS IN ALL KINDS OF SOIL |
| 159 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil & disposal of surplus excavated soil as directed, within or outside the site at an unobjectionable place. |
| 160 | EXC. IN ALL KINDS OF SOIL |
| 161 | EXC. IN ORDINARY ROCK |
| 162 | EXC.EXTRA LIFT EVERY 1.5M ALL KIND SOIL |
| 163 | EXC. - EXTRA LIFT EVERY 1.5M HARD ROCK |
| 164 | FILLING AVAILABLE EARTH |
| 165 | SUPPLY AND FILLING IMPORTED EARTH |
| 166 | Supplying and filling in plinth with sand within specified grading zone of fine aggregates specified in table 3.1, clause 3.1.3 of attached specifications under floors, etc. in layers not exceeding 20cm in depth, each deposited layer to be compacted by ramming including watering, consolidating and dressing complete. |
| 167 | SUPPLY FILLING LOCAL SAND ZONE IV |
| 168 | Providing and laying in position cement concrete of specified grade excluding cost of centering & shuttering. All work up to plinth level: |
| 169 | 1 CEMENT:2 COARSE SAND:4 AGG. 20MM |
| 170 | 1 CEMENT:3 COARSE SAND:6 AGG. 20MM |
| 171 | Centering and shuttering including strutting, propping etc. and removal of form work for: |
| 172 | CENT.& SHUT.FOR PCC-FOUND,FOOTING ETC |
| 173 | CENT.& SHUT. FOR PCC IN WALL,ETC. |
| 174 | PRE-CAST CC 1:2:4 KERB STONE,..WITH C&S |
| 175 | 40MM DAMP PROOF COURSE |
| 176 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level |
| 177 | RCC 1:1½:3 UP TO PLINTH LEVEL W/O C&S |
| 178 | Providing & Laying Reinforced cement concrete work in walls (Any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level UP TO FLOOR V LEVEL excluding cost of centering, shuttering, finishing and reinforcement : |
| 179 | RCC 1:1½:3 WALLS ..UPTO 5 LVL W/O C&S |
| 180 | Centering and shuttering including strutting, propping etc. and removal of form for : |
| 181 | CENT.& SHUTT. FOR RCC FOUNDN,FOOTING |
| 182 | CENT.& SHUTT. FOR RCC WALLS ETC. |
| 183 | CENT.& SHUTT. FOR RCC SLABS, ROOFS |
| 184 | CENT.& SHUTT. FOR RCCLINTELS, BEAMS |
| 185 | CENT.& SHUTT. FOR RCC COLUMNS |
| 186 | CENT.& SHUTT. FOR RCC FINS |
| 187 | CENT.& SHUTT. WITH PLY FOR RCC BEAMS |
| 188 | Supply of Steel reinforcement for R.C.C. including straightening, cutting, bending, placing in position and binding all complete at all levels |
| 189 | TMT BARS FE- 500 GRADE |
| 190 | Providing and laying Brick work with common burnt clay F.P.S (non Modular) bricks of class designation 7.5 in foundation & plinth |
| 191 | BRICK WORK IN CM 1:6 IN FOUNDN & PLINTH |
| 192 | BRICKWORK IN CM 1:6 IN S/STR UPTO LVL V |
| 193 | HALFBRICK MAS IN CM1:4 S/STR UPTO LVL V |
| 194 | DRY BRICK ON EDGE FLOOR IN MUD MORTAR |
| 195 | Providing and fixing 18mm thick gang saw cut mirror polished premoulded and prepolished, machine cut for kitchen platforms, vanity counters, sills, facias, Pump Island & similar locations of required size, approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding & polishing to edge to give high gloss finish etc. complete at all levels. |
| 196 | POLISHED GRANITE - KITCH.CUNTR<0.50SM |
| 197 | Extra for providing edge moulding to 18mm Granite/ marble stone counters,Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in- Charge. |
| 198 | EXTRA FOR EDGE MOULDING TO GRANITE WORK |
| 199 | EXTRA FOR OPENING FOR WASH BASIN ETC. |
| 200 | MS GRILLS TO WINDOWS |
| 201 | CHROME PLATED FLOOR DOOR STOPPER |
| 202 | AL. HYDRAULIC DOOR CLOSER |
| 203 | 100X72MM CHROME PLATED MORTISE LOCK |
| 204 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions,at top, bottom & sides with with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/panelling, C.P. brass/stainless steel screws including fixing all complete as per drawing & the directions of Engineer-in-charge. (Cost of glazing or panels to be paid for separately) |
| 205 | POWDER COATED AL.SECN,FIXED GLAZING |
| 206 | POWDER COATED AL.SECN, SHUTTERS |
| 207 | Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminium doors, windows shutters and partition frames with C.P. brass/stainless steel screws etc. complete as per directions of Engineer in charge |
| 208 | PRE-LAM BOTH SIDE DECO.BOARD IN AL.SEC. |
| 209 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item): |
| 210 | FLOAT GLASS 6.0MM IN AL.SEC. |
| 211 | FLOAT GLASS 8.0MM IN AL.SEC. |
| 212 | Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS : 6315 having brand logo embossed on the body/plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. |
| 213 | DBL ACTION FL.SPRING- BRASS COVER PLATE |
| 214 | 100MM BRASS LOCKS OF APPD.MAKE |
| 215 | Providing and fixing aluminium round shape handle of outer dia 100mm with SS screws etc. complete as per direction of Engineer-in- charge |
| 216 | POWDER COATED AL.ROUND SHAPE HANDLE |
| 217 | P/FIXING 12MM FRAMELESS TOUGHENED GLASS |
| 218 | STRUCTURAL STEEL WORK IN SINGLE SECTION |
| 219 | STR.STEEL IN BUILT UP SECTION |
| 220 | ROLLING SHUTTERS |
| 221 | Steel work in built up tubular (round,square or rectangular hollow tubes etc) trusses etc. including cutting,hoisting fixing in position and applying a priming coat of approved steel primer, including welded and bolted with special shaped washers etc. complete. |
| 222 | HOT FINISHED WELDED TYPE TUBULAR TRUSS |
| 223 | MS 16MM DIA FAN CLAMPS |
| 224 | MS GRATINGS,FRAMES,LADDER ETC. |
| 225 | CERAMIC GLAZED TILES FOR WALLS |
| 226 | CERAMIC GLAZED TILES FOR FLOORING |
| 227 | Providing & laying vitrified floor tile in different sizes (thickness as per manufacturer) with water absorption's less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar as specified with coarse sand jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc. complete for flooring/skirting as specified |
| 228 | 60X60 CM VITRIFIED FLOOR TILES |
| 229 | 60X60 CM VITRIFIED TILES FOR SKIRTING |
| 230 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS:13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion, Single socketed pipes. |
| 231 | 110MM PVC RAIN WATER PIPE |
| 232 | Providing & fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS:13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion. |
| 233 | 110MM UPVC COUPLER |
| 234 | 110MM UPVC SINGLE PUSHFIT COUPLER |
| 235 | UPVC SINGLE T WITH DOOR 110X110X110MM |
| 236 | UPVC SINGLE T WITHOUT DOOR - 110MM.. |
| 237 | UPVC 87.5 DEGREE BEND OF 110MM |
| 238 | UPVC PLAIN SHOE OF 110MM |
| 239 | Providing & fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work & fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. |
| 240 | 110 MM UPVC PIPE CLIPS |
| 241 | Providing and laying cement plaster on surfaces with fine sand including curing etc. |
| 242 | 12MM CEMENT PLASTER,1:6 WITH FINE SAND |
| 243 | 20MM CEMENT PLASTER,1:6 WITH FINE SAND |
| 244 | Providing and laying 6mm thick cement plaster on surfaces with fine sand including curing etc. |
| 245 | 6MM CEMENT PLASTER WITH FINE SAND |
| 246 | NEAT CEMENT PUNNING |
| 247 | 2MM THK POP PUNNING OVER PLASTER |
| 248 | ACRYLIC SMOOTH EXTERIOR PAINT |
| 249 | DELUXE MULTI SURFACE PAINT SYSTEM |
| 250 | DELUXE MULTISURFACE PAINT-STEEL SURFACE |
| 251 | SYNTHETIC ENAMEL PAINT |
| 252 | Carriage charge for disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, stacking, unloading to approved municipal dumping ground/unobjectionable place as/direction of Engg- in-Charge beyond IOCL Premises for all leads and including all lifts |
| 253 | MALBA & WASTE CARRIAGE < 1 KM |
| 254 | MALBA & WASTE CARRIAGE > 1 km < 3 km |
| 255 | Construction of granular sub-base by providing close graded material conforming to specifications, mixing in a mechanical mixer plant at Optimum Moisture Content, carriage of mixed material by tippers to work site, for all lead and lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface & compacting with vibratory power roller to achieve the desired density, complete as per specification & direction of Engineer-in-charge. |
| 256 | GRANULAR SUB BASE -75MM TO 0.75MM |
| 257 | WET MIX MACADAM |
| 258 | Providing & laying factory made reflective type Lacquered finish Grey / coloured pre-cast cement concrete, interlocking paver block of specified grade made by block making machine wih vibratory compaction & of approved size and design / shape, shade and manufacturers and as per IOCL's specifications. The paver blocks shall have peripheral chamfer, with average crushing strength as per IS 15658, maximum water absorption of 2% after 10 minutes and 5% after 24 hrs. as per BS 1881, maximum dimensional deviations of +/- 2mm on length @ width and +/- 3 mm on thickness. The job includes supplying and laying a layer of 50 mm thick clean coarse sand on thoroughly compacted sub-base below the paver blocks, cutting the paver blocks wherever required with hydraulic splitter, filling in the joints at the edges of paver blocks with sand, compacting with machine vibrator to required line and level, etc. complete. (Payment for provision of edge restraints shall be made separately) |
| 259 | P/L REFLECTIVE LAQUERED M40 80MM THK PAV |
| 260 | 100MM SCI GULLY TRAP |
| 261 | 600X450 BEVELLED EDGE MIRROR |
| 262 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Internal work - Exposed on wall |
| 263 | CPVC PIPES 40MM INTRNAL EXPOSED ON WALL |
| 264 | CPVC PIPES 50MM INTRNAL EXPOSED ON WALL |
| 265 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work including cutting chases and making good the walls etc. |
| 266 | CPVC PIPES 15MM CONCEALED |
| 267 | CPVC PIPES 20MM CONCEALED |
| 268 | CPVC PIPES 25MM CONCEALED |
| 269 | CPVC PIPES 32MM CONCEALED |
| 270 | Providing and fixing brass bib cock of approved quality : |
| 271 | 15MM BRASS BIB COCK |
| 272 | 20MM BRASS BIB COCK |
| 273 | Providing and fixing brass stop cock of approved quality : |
| 274 | 15MM BRASS STOP COCK |
| 275 | 20MM BRASS STOP COCK |
| 276 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : |
| 277 | 25MM GUN METAL VALVE WITH CI WHEEL |
| 278 | Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : |
| 279 | 150MM DIA CP BRASS SHOWER ROSE |
| 280 | PROVIDING POLYETHYLENE TANK ON TERRACE |
| 281 | 15MM CP BRASS LONG BODY BIB COCK |
| 282 | Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I.cover with frame of 300 x300 mm size(inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design : |
| 283 | 100X100MM GULLY TRAP WITH COMMON BRICKS |
| 284 | SOAK PIT 2.5M DIA X 3M DEPTH |
| 285 | WATER PROOFING WITH BRICK BAT COBA |
| 286 | Writing name of Retail Outlet and location/ Indian Oil Corporation monogram, other sign / slogans on building / glass of show window etc. of the following heights / diameters with vinyl sticker of approved quality and shade. 150 micron thick Non Reflective Vinyl sticker 3M or Equivalent Brand |
| 287 | LETTER SIZE 26-70CM |
| 288 | Providing and fixing CP Brass 32mm size |
| 289 | Providing and fixing Chrome Finish SS He |
| 290 | Providing and fixing front operated conc |
| 291 | Providing and fixing first quality (heav |
| 292 | Providing and fixing H type double tone |
| 293 | Providing and fixing stainless steel (SS |
| 294 | CABLING AND ALLIED WORKS - ARMOURED CABLES Supply & laying of XLPE insulated PVC sheathed aluminium/copper conductor, 1.1 kV grade armoured cable conforming to IS:7098, as per approved make in ground/ trench/surface/pipe, etc. whereever required as per direction of Engineer In-charge. Note: The rate of Installation should be inclusive of Cable clamps, tags Saddles, Consumables etc. Trays/pipes, trenches, fabricated tray supports etc will be covered & paid in Separate Items |
| 295 | S&L 3X2.5 SQMM,1.1KV FRLS CU ARMD CABLE |
| 296 | S&L 4X2.5 SQMM,1.1KV FRLS CU ARMD CABLE |
| 297 | S&L 4X16 SQMM,1.1KV ALUMINIUM CABLE FRLS |
| 298 | S&L3.5X35 SQMM,1.1KV ALUMNM CABLE FRLS |
| 299 | CABLE TERMINATION GLANDS NON-FLP HEAVY DUTY DOUBLE COMPRESSION Cable Termination (NON FLP): Providing termination of 1.1 kV grade armoured cable for the following sizes including supply of NON FLP heavy duty Double Compresson cable glands, crimping type lugs and allied jointing materials, etc. all complete as per specification and direction of Engineer In-charge. Glands and lugs shall be of approved make. Copper lugs for copper cables and aluminium lugs for aluminium cables shall be used. |
| 300 | CABLE TERM,NON FLP DC GLAND 3X2.5SQMM |
| 301 | CABLE TERM,NON FLP DC GLAND 4X2.5SQMM |
| 302 | CABLE TERM,NON FLP DC GLAND 4X16SQMM |
| 303 | CABLE TERM,NON FLP DC GLAND 3.5X35SQMM |
| 304 | CABLE TERM,NON FLP DC GLAND 3.5X70SQMM |
| 305 | S&F OF FLP JUNC. BOX (4 WAY ENTRY) |
| 306 | Supply & drawing/laying, jointing, connecting, testing and commissioning of earth strip/copper strip/GI wire for earthing and lightning protection under or aboveground complete as per specification for the following : |
| 307 | EARTHING WITH 25 X 3 MM GI STRIP |
| 308 | PROVIDING INTERNAL WIRING |
| 309 | LIGHT/FAN/5A POINT, WIRING, MOD SWITCH |
| 310 | LIGHT/POWER PLUG, WIRING, MOD SWITCH |
| 311 | Supplying, drawing sub-main/power wiring with PVC insulated Copper 1100 V grade FRLS type through heavy duty rigid PVC conduit either on wall or in concealed. The job include terminations at both ends through proper jointing materials all complete for the following Make of Insulated wires shall be as per approved make |
| 312 | SUBMN WIRE-2X1.5SQMM,EARTHWIRE 1X1.5SQMM |
| 313 | SUBMN WIRE-2X2.5SQMM,EARTHWIRE1X2.5SQMM |
| 314 | SUBMN WIRE-2X4SQMM,EARTHWIRE 1X4SQMM |
| 315 | SUBMN WIRE-2X16SQMM,EARTHWIRE 1X16SQMM |
| 316 | SWITCHES, FUSES, MCBS, ELCBS ETC Supply and fixing of Modular switch frame with inner and outer face plates and accessories as per following details of approved including flush metal boxes/surface mounting boxes, plates, etc. all complete as per manufacturer's specification and direction of Engineer In-charge. |
| 317 | S&F SWITCH WITH 1 OR 2 MODULE FRAME |
| 318 | S&F SWITCH WITH 3 MODULE FRAME |
| 319 | S&F SWITCH WITH 4 MODULE FRAME |
| 320 | S&F SWITCH WITH 6 MODULE FRAME |
| 321 | S&F SWITCH WITH 8 MODULE FRAME |
| 322 | S&F SWITCH WITH 12 MODULE FRAME |
| 323 | S&F 6A MODULAR SWITCH |
| 324 | S&F 15 A MODULAR SWITCH |
| 325 | S&F 6A, 3 PIN MODULAR SOCKET |
| 326 | S&F 15 A 6 PIN MODULAR SOCKET |
| 327 | S&F FAN REGULATOR OF STEPPED MODULAR |
| 328 | Supplying and fixing of following MCBs with necessery inter connections on existing DB, Panel board etc. |
| 329 | S&F MCB+ELCB UPTO 32A SP MCB |
| 330 | S&F MCB+ELCB UPTO 32A DP MCB |
| 331 | Supply and installation of MCB distribution board having Double door complete with tinned cu bus bar, neutral bus bar, earth bar, din bar, interconnection, earthing etc. without incoming isolator and MCBs |
| 332 | S&F MCB DB WITH 4 WAY (4+12) TPN |
| 333 | S & I OF ESD SYSTEM |
| 334 | HOARDING LIGHTS:30W WITH IP65 PROTECTION |
| 335 | LED TUBE LIGHT: 18W WITH IP65 PROTECTION |
| 336 | LED TUBE LIGHT: 8W WITH IP20 PROTECTION |
| 337 | CEILING FANS Supply & fixing of ceiling fan for inside of the sales building of following type: |
| 338 | S&I 1200 MM SWEEP CEILING |
| 339 | EXHAUST FANS Supply and fixing of exhaust fan including electrical wiring all shall be with per specification and direction of site In charge. The fans shall be with louvers / shutters. (The job does not include making suitable cut out in the wall for fixing the fan). |
| 340 | S&I 9\\" LIGHT DUTY EXHAUST FAN KHAITAN/EQ |
| 341 | Supply & laying of Heavy Duty type, High compression strength, IP 67 rated (DWC) Double wall corrugated HDPE Conduits as per IS:14930/ IS:16205. Laying includes with GI pull wires inside the conduits & necessary ends to be filled with sealants, of all complete and as per drawing & specification. |
| 342 | Supply & laying of Heavy Duty type Doubl |
| 343 | Providing and fixing of 63 Amp ELCB 3 ph |
| 344 | Providing and laying Bitumen Penetration Macadam with hard stone aggregate of quality, size and grading as specified, with bitumen of suitable penetration grade including required key aggregate as specified spreading coarse aggregate with the help of self propelled/ tipper tail mounted aggregate spreader and applying bitumen by a pressure distributor and then spreading key aggregate with the help of aggregate spreader complete, including consolidation with road roller of minimum 8 to 10 tonne capacity to achieve specified values of compaction and surface accuracy : |
| 345 | 50MM BITUMINOUS PENETRATION MACADAM |
| 346 | Providing and applying tack coat using hot straight run bitumen of grade VG-10 including heating the bitumen, spraying the bitumen with mechanically operated spray unit fitted on bitumen boiler, cleaning and preparing the existing road surface as per specifications : |
| 347 | TACK COAT ON WBM @0.75KG/SQM |
| 348 | 2.5 cm Premix carpet surfacing with 2.25 cum and 1.12 cum of stone chippings of 13.2mm and 11.2mm size respectively per 100 sqm. and 52 kg. and 56 kg. of hot bitumen per cum of stone chippings of 13.2 mm and 11.2 mm size respectively including a tack coat with hot straight run bitumen, including consolidation with road roller of 6 to 9 tonne capacity etc. complete. (tack coat to be paid for separately) : |
| 349 | 25MM PREMIX CARPET WITH VG-10 |
| 350 | Providing and applying tack coat using hot straight run bitumen of grade VG-10 including heating the bitumen, spraying the bitumen with mechanically operated spray unit fitted on bitumen boiler, cleaning and preparing the existing road surface as per specifications : |
| 351 | TACK COAT ON BITUMINOUS SURFACE |
| 352 | P/L PREMIX SEAL COAT |
| 353 | COUNTER SUNK WASH BASIN Please Enable Macros to View BoQ information |
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail