|
| 1 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :-1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 2 | Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction of Engineer- in-charge-Extruded section profile size 48x40 mm |
| 3 | Providing and fixing to existing door frames.-24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-in-charge. (For W.C. and bathroom door shutter). |
| 4 | Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all complete.-With 2nd class teak wood beading 62X19 mm |
| 5 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.-Hot finished welded type tubes |
| 6 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. |
| 7 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.-110 mm diameter |
| 8 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.-Single tee without door-110x110x110 mm |
| 9 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.-Bend 87.5°-110 mm bend |
| 10 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 11 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC (Volatile Organic Compound ) content less than 50 gram/ litre, of approved brand and manufacturer including applying additional coats wherever required to achieve even shade and colour -Old work (one or more coats) |
| 12 | Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. |
| 13 | Finishing walls with Acrylic Smooth exterior paint of required shade :-Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface |
| 14 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :-Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture |
| 15 | Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge.-With cement mortar 1:4 (1cement: 4 coarse sand) |
| 16 | Renewing glass panes, with putty and nails wherever necessary including racking out the old putty:-Float glass panes of nominal thickness 5 mm (weight not less than 12.5kg/sqm) |
| 17 | Renewal of old putty of glass panes (length) |
| 18 | Disconnecting damaged overhead/terrace PVC water storage tank of any size from water supply line and removing from the terrace including shifting at ground level as per direction of Engineer-in-charge. |
| 19 | Dismantling W.C. Pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in-Charge. |
| 20 | Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer 3 mm thick water proofing membrane, black finished reinforced with non-woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrane manufacture of density at 25°C, 0.87-0.89 kg/ litre and viscocity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torch and sealing all joints etc, and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 650/ 450N/ 5cm. Tear strength in longitudinal and transverse direction as 300/250N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane :-3 mm thick |
| 21 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.-Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix) |
| 22 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.-For thickness of tiles 10 mm to 25 mm |
| 23 | Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead. |
| 24 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:-White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests |
| 25 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:-White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps |
| 26 | Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete.-10 litre capacity - White |
| 27 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 28 | Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. |
| 29 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.-450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms |
| 30 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.-Internal work - Exposed on wall-15 mm nominal dia Pipes |
| 31 | Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.-15 mm dia nominal bore |
| 32 | Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :-100 mm diameter |
| 33 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 34 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :-15 mm nominal bore |
| 35 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.-15 mm nominal bore |
| 36 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.-15 mm nominal bore |
| 37 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931-15mm nominal bore |
| 38 | Modified Estimated Cost after using Correction factor on DSR 2023 on acount of GST @ 0.973 |
| 39 | Add Cost Index @ 60% on DSR 2023 |
| 40 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with piano type switch, phenolic laminated sheet, suitable size M.S. box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required. Group-A |
| 41 | Rewiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable and 1.5 sq.mm FRLS PVC insulated copper conductor single core cable as earth wire in existing surface/ recessed steel/PVC conduit including dismantling as required. |
| 42 | Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required.a) 3 x 6 sq. mm |
| 43 | b) 3 x 4 sq. mm |
| 44 | c) 3 x 1.5 sq. mm |
| 45 | Supplying and fixing following Piano type switch/ socket on the existing switch box/ cover including connections etc. as required.a) 5/6 Amp. Switch |
| 46 | b) 2 way 5/6 A switch |
| 47 | c) 3 pin 5/6 Amp. Socket outlet |
| 48 | d) 15/16 A switch |
| 49 | e) 6 pin 15/16 A socket outlet |
| 50 | Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc. as required. |
| 51 | Supplying and fixing PVC batten/ angle holder including connections etc. as required |
| 52 | Supplying and fixing call bell / buzzer suitable for single phase, 230 volts complete as required. |
| 53 | Providing and fixing following capacity TP&N disconnector switch fuse unit inside the existing panel board with ISI marked HRC fuse including drill holes in cubical panel,making connection,etc as requried.32 Amp TP & N |
| 54 | Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreader in existing cubical panel board including drilling holes in cubical panel, making connection ,etc as requried. 200 Amp , 36 KA,FP MCCB |
| 55 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required single pole. |
| 56 | Supplying and fixing following rating,doube pole,240 V,isolator in the existing MCB DB complete with connection, testing and commissioning etc as required. 40 A |
| 57 | Add GST @ 18% on DSR 2022 items (MF= 0.0633) on DSR Items |
| 58 | Add labour cess @ 1% On DSR -22 Items |
| 59 | Providing and fixing of 20 Watt, 6500K LED decorative ultra slim square profile LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient ready to use pack directly on ceiling/ wall, including round sheet,connections, testing and dismantling the existing complete etc. as required. Havells (LED PRIDE ESSENTIAL) Ordering code LHEXAWP7IN1W020 make or or equivalent model & specification in philips/ Crompton/ Bajaj required. |
| 60 | Supplying and fixing of 230 mm sweep heavy duty exhaust fan suitable for single phase, 50 Hz, 230 volts, AC supply in existing opening including making the hole to suit the size of above exhaust fan & S/F of louver / shutter including connection, testing and making connection with 1.5 sq.mm., FR, PVC insulated, copper conductor, single core cable and earthing etc. as required etc Havells ventil air DSP FHVVEMTDBS09 make equivalent to Bajaj / Crompton / Havells / Khaitan. |
| 61 | Supplying and fixing of 30 W LED street light luminaire fitting energy saving and environment friendly long life LED street light made up of pressure die cast aluminium housing with acrylic cover as diffuser with IP66 and Impact resistance of IK07 Philips/Bajaj/Crompton/ Havells make compatible to Havells code No LHETAVU7PA7J030 with 32 mm dia G I pipe bracket of 1 mtr length bend to required shape on existing poles with suitable Clamps for 32 mm dia G I pipe with nuts & bolts and washers. , including wiring with 2 x 1.5 Sqmm (from over head line to LED fitting), FRLS, PVC insulated, single core, copper conductor cable & making connection of LED street light luminaire etc. as required of make Philips /CG / Bajaj / Havells |
| 62 | Supplying and Laying of one number3.5 core 35 Sqmm PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation and refilling the trench etc as required, but excluding sand cushioning and protective covering.Make KEI/Havells/polycab |
| 63 | Supplying and fixing of phenolic laminated sheet on existing GI metal box switch board / cover. |
| 64 | Supplying,installation testing and commissioning of energy efficient - 1 star rated, 1200 mm sweep ceiling fan including wiring the down rods of standard length (upto 30 cm) with 1.5sq. mm FRLS PVC insulated, copper conductor, single core cable, complete etc. as required colour- White / Brown / Ivory etc as required. (make - Usha/Havells/crompton /khaitan/Bajaj/ orient CG) |
| 65 | Total Cost (BoQ1+BoQ2) |
| 66 | Civil work |
| 67 | Elect work Please Enable Macros to View BoQ information |
