Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | CIVIL (Renovation & Furnishing) : Removing old lime or cement plaster from walls including raking out joints 12mm deep and removing the debris within 50m lead or as direction of E.I.C. |
| 2 | Clearing and removal of unwanted vegetation, such as bushes, shrubs, and small trees, from a Tourism Development Office premises etc. completed |
| 3 | Dismantling and removing cement concrete including stacking the useful materials for reuse and removing the debris within 50m lead. |
| 4 | Apply a coat of Damp Proof Compound (diluted with water in the ratio 2:1) as a self-priming coat at the rate 10 –11.00 sq.mt. /liter/coat in SSD condition. Apply 1st coat of Dr. Fixit Roofseal Classic New at the rate of 0.50 / litre / Sq.mt / Coat. Laying a 45 GSM glass fibre mesh of 2.5 mm x 2.5 mm sandwiched between the first and second coat. While the 1st coat is still wet. Allow the first coat to dry for 4-6 hours. Apply second coat of Dr. Fixit Roofseal Classic New with the same application coverage. Application direction of second coat should be perpendicular to that of the first coat. Allow second coat to dry for 4-6 hours. Apply third coat of Dr. Fixit Roofseal Classic New at an application direction that is perpendicular to that of the second coat with same application coverage rate to achieve total dry film thickness of 750 to 800 microns at forced coverage at the rate of 1.50 – 1.60 litre / Sq.mt in 3 coats. Check to see no void surface is left untreated / uncoated. Allow the system to air cure for 7 days minimum. The material having following technical Specification ASTM D 6083 M – Type II, Attains a Tensile Strength of 2.5 N/mm2 confirming to ASTM D 2370; Elongation at break ≥ 200% confirming ASTM D 2370, Adhesion to Concrete 2.0 N/mm2 confirming ASTM D 4541 and Crack bridging ability up to 2 mm, Air cure the coating for 7 days, before water pound test for 48 hrs. The system comes with 10 years waterproofing warranty from M/S Pidilite Industries or, equivalent make. |
| 5 | Providing and injecting chemical emulsion for pre - constructional antitermite treatment as per IS specification and creating a chemical barrier in bottom and sides of foundation trenches, top-surface of plinth filing junction of walls and floors along with external perimeter of the building expansion joints surrounding the pipes and cables etc. complete using approved quality of chemical emulsion of requisite quantity prescribed by the manufacturer as directed by the Engineer-in-charge including cost of all materials and labour taxes etc. complete. (indemnity bond for warranty for 5 years to be furnished) Ground Floor |
| 6 | Repairing of Door and window etc. completed.(Carpenter 2nd Class) |
| 7 | Scraping old paint with scrapers, sand papering and washing with soap water or soda including scaffolding charges upto 5M height |
| 8 | Providing Fly Ash Brick masonry using fly ash bricks of size 23 cm. x 11 cm. x 8 cm. having crushing strength not less than 75 kg. Per. Sqr. Cm. in cement mortar of mix(1:6) with ordinary Portland slag cement(PSC) and screened & washed sand for mortar in foundation, plinth, basement and for ornamental flower beds, plinth moulding and similar such type of works with all necessary projections, splays cutting, circular moulding, corbelling, chamfering and similar such type of works, watering and curing etc. including cost, conveyance, loading, unloading, royalties and taxes of all materials, cost of all labour, scaffolding, sundries, T&P required for the works etc. complete in all respect as per specification and direction of Engineer-in-charge. |
| 9 | Providing 16 mm. thick cement plaster in all floors at all height with cement mortar of mix (1:6) with portland slag cement (PSC) finished smooth to inside rough surface of brick masonry walls after racking out joints including watering and curing rounding of corners etc. complete with cost, coveyance, loading and unloading, royalties and ,es of all materials and cost of all labour, T&P, sundries and scaffolding required for the work etc. with providing grooves as directed by the Engineer in charge. |
| 10 | Cleaning of septic tank and inspection chambers by mechanical/manual means, including dewatering, removal and safe disposal of sludge, scum, and accumulated waste, washing with water, reinstating covers, and making the system operational, complete as per specifications and directions of the Engineer-in-Charge.(unskilled labour) |
| 11 | Providing and fixing in position wood plastic composite door frame with appropriate length of ETA Approved carbon steel galvanized (minimum 5 microns) double threaded 6.8 grade Polyamide PA 6 grade sleeve HRD C 10 anchor suitable for fastenings both on concrete & masonary/aerated blocks including cost of all materials, labours, T & P etc required for the work. complete in all respect as directed by the Architect/Engineer-in-charge |
| 12 | Providing and fixing of 35mm thick WPC Door Shutter(Solid) with teak edge leaping to the periphery of the shutter with pilishing as per detailed drawing with including, all hardwares & fixtures, SS tower bolt(150mm),Door stopper,SS aldrop(250mm),SS handle(200mm length),ss handle (150mm length) & SS Butt hinges -125mm x 65mm x2.12mm .including cost, conveyance, loading, T&P required for the work etc. complete in all respect as directed by the Engineer-in-charge |
| 13 | Wall painting two coats with 100% Acrylic emulsion paint (1st quality) exterior grade of approved make & shade manufactured by reputed manufacturer like NEROLAC / ASIAN / BERGER / DULOX or equivalent to make an even finished surface over a coat of primer with water bond cement primer in all heights with all scaffolding and staging charges including cost, conveyance, taxes of all materials, cost of all labours, T & P, sundries etc. as required for the work complete. |
| 14 | Providing and painting two coats with plastic emulsion paint of (Nerolac/ Asian/ Berger/ Dulox or equivalent make) approved quality and approved shade over coat of primer of approved quality in all floors at all height by making the surface to the interior plastered surface over a coat primer with water bond cement primer of approved quality including cost, conveyance, loading and unloading of all materials, cost of all labour, sundries, T & P, scaffolding etc. required for the work and complete in all respect as per specification and direction of Engineer-in-charge. |
| 15 | a. G. F |
| 16 | b. F. F |
| 17 | Finishing surfaces of walls with Cement based wall Putty (Water based) of approved make & finished smoothand even surface to receive painting including cost of scaffolding staging charges with cost of all materials taxes , labour T &P etc complete. |
| 18 | Providing and painting two coats with synthetic enamel paint of approved quality and approved shade confirmming to ISI on steel work to give an even shade in all floors at all height over a coat of primer of approved quality and shade including sand papering and making the surface smooth with cost, coveyance, loading and unloading, and , cost of all labour, sundries, T&P, scaffolding etc. required for the work and complete in all respect as directed by Engineer-in-charge. |
| 19 | Supplying, fitting and fixing of M.S grills, grill gates with top and bottom rails, steel windows, steel doors, steel frames for doors and windows, staircase and parapet railing ( as per I.S. specification and as per approved drawings ) in proper position in all floors and at all height including making holes to brick walls/ R.C.C structure/wood work etc. and making good to the damaged walls/ structures with cement concrete (1:2:4) with black hard crusher broken granite stone chips of 12mm to 20mm size ( 20mm size not to exceeds 25% ) including watering and curing etc. complete in all respect as directed by the Engineer in charge ( W.I. / M.S. windows grills, grill gates, collapsible gates with top and bottom rails, steel windows, steel doors, steel frames for doors and windows, staircase and parapet railings square bar along with required nos. of nails and screws and other required materials of approved quality and approved size shall be supplied by the contractor at his own cost.) |
| 20 | PH Fittings :Supplying & Fixing Short body Bib cock of CP brass of Jaquar continetnal cat no- FLR-5041N or equivalent including making good the damages including tools, plant, all material,labour , scaffolding etc. complete in all respects. |
| 21 | Supplying all materials, labour, T&P and fixing standard sized 15mm dia Angular Stop cock of Jaquar Cat. No.-FLR-5053N or equivalent type of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in-charge. |
| 22 | Supplying all materials, labor T&P for fitting and fixing in all floors' fixed type Glass mirror of size 900mm x 600mm best INDIAN make of 5.5 mm thickness with supply of 13mm thick asbestos backing and wooden plugs C. P. Brass screw including cost, conveyance, royalty, taxes of all materials complete as per P.H. specification and direction of Engineering-in-charge. |
| 23 | Supplying all materials, labour, T&P and fixing Two way Bib cock of Jaquar Cat. No.-FLR-5041N or equivalent type of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in-charge. |
| 24 | Supplying all materials, labour, T&P and fixing standard sized CP Towel rail - 24\\" of Jaquar Cat. No.-AKP 35711PS or equivalent type of approved make etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in-charge. |
| 25 | Supplying all materials, labour, T&P and fixing standard sized CP Towel ring of Jaquar Cat. No.-AKP 35721P or equivalent etc complete including cutting the wall and making good the damages, including cost of all materials complete as per PH specification and direction of Engineering-in-charge. |
| 26 | Providing and fixing UPVC pipes of Schedule-80 ( AJAY/ ASHIRVAD/ ASTRAL / SUPREME / ORI-PLAST ETC) including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. ( Hydrostatic(water) testing, Air(pneumatic) testing should be checked at the time of execution) |
| 27 | a. 25 mm nominal outer dia Pipes |
| 28 | b. 32 mm nominal outer dia Pipes |
| 29 | c. 50 mm nominal outer dia Pipes |
| 30 | Supplying all materials, labour, T&P and fitting and fixing U-PVC SWR soil waste ventilating pipes (selfit / ring fit type ) with all PVC fittings of Finolex /Prince/Supreme/equivalent make as per IS 13592 to walls with nails, bobbins and wooden plugs or laying in trenches including all pipe fittings, jointing materials, tools plant, labour & all material, earthwork in excavation in all kinds of soil and refilling of trenches as per specification and direction of the engineer in charge. |
| 31 | a. 160mm dia PVC (SWR) pipe class \\"A\\" ( with wall thickness of 3.2mm to 3.8mm) |
| 32 | b. 110 mm dia PVC (SWR) pipe Class ‘A’ (with wall thick of 2.20 mm to 2.70 mm) |
| 33 | c. 75 mm dia PVC (SWR) pipe Class ‘A’ (with wall thick of 1.8 mm to 2.20 mm ) |
| 34 | Supplying all materials, labour, T&P and fittings and fixing of 2000 ltr Poly Propelene white double layer water storage Tank of approved make confirming to IS 12701-1996 including cutting holes through the tank and fixing mild steel tubes and fittings and providing extra sockets and jam nuts, fixing ball valve etc including hoisting upto terrace level and placing the tank to the required position etc all complete as per PH specification and direction of Engineer-in-charge. (To provide with brick masonary guard walls which will be paid separately) |
| 35 | Supplying all materials, labour, T&P and providing, fitting and fixing submersible pump with squirrel cage induction type submersible type submersible electric motor to run on 3 phase/1 phase line voltage ranging from 320 volt to 450 volt conforming to IS: 8034/89 with following specifications with suitable control panel, jointing with GI/PVC/HDPE pipes, electrification, testing, commissioning, trial running, conveyance of all materials to worksite, payment of taxes etc all complete as per specification and direction of the Engineer in charge (Texmo/Crompton Greaves/Kirloskar make) 1 H.P. Single phase/ three phase 3 stage head renge of 20 to 35 mtr with discharge capasity 145 to 110 L.P.M With outlet dia 25 mm (keeping 100% standby) |
| 36 | Supply of Aluminium Ladder of 36feet length etc. completed. |
| 37 | Two Wheeler Parking- Earthwork in excavation in all kinds of soil upto 1.50mtr depth of foundation trenches for columns, basement, tie beams, walls and steps in following types of soil including moorum, hard stony earth, earth mixed with boulders, DI rocks etc but not requiring blasting with initial leads and lifts including dressing and leveling the bed sides up to required depth and depositing the excavated materials at places away from the work site with T&P for shoring, shuttering, dewatering if required etc. complete as per the drawing, design including cost of all labour, T&P etc. as required for the work complete as directed by the Engineer-in-charge. |
| 38 | Supplying and filling the Foundation & Plinth with clean coarse river sand of approved quality from approved quarry, laying in layers not exceeding 150mm thick, watering and ramming including cost, conveyance, royalty and cost of all labour, T&P etc. as required for the work complete as per direction of the Engineer-in-charge. |
| 39 | Providing and lying plain cement concrete of proportion (1:4:8) in foundation and floors using Portland Slag Cement(PSC) with 4 cm. Size black hard crusher broken granite stone metal and screened and washed sharp sand for mortar of approved quality from approved quarry, washed and cleaned including hoisting, lowering, laying concrete, ramming, watering and curing etc. complete to required levels laid in layers not exceeding 15 cm thick in each layer including cost, conveyance, loading, unloading, royalties and cost all labours, sundries, T & P required for the work including shoring, shuttering and dewatering if required including hire & running charges of water pump complete as per specification and direction of Engineer-in-charge. |
| 40 | Providing, lifting, hoisting and laying Reinforced cement concrete of different RCC structure in foundation level of M-250 grade as per approved designs and drawings having a minimum compressive strength (in work test) 250 Kg. / Square cm. in 15 cm. cubes at 28 days after mixing and test conducted in accordance with I.S. 516 using 12 mm. to 20 mm. size black hard crushed broken granite stone chips and screened and washed sharp sand for mortar of approved quality from approved quarry, washed and cleaned ( 20mm. size chips not to exceeds 25 % ) to be mixed in concrete mixture with Portland slag cement (PSC) including hoisting, lowering, laying and compaction concrete by using vibrators, watering and curing for 28 days, centering and shuttering then after dismantling and removing debris from the work site and finishing the exposed surface smooth providing grooves or beads wherever necessary including cost, conveyance, loading, unloading, royalties and cost of all labours, sundries, T & P required of the work etc. complete in all respect as directed by the Engineer-in-Charge. But excluding cost and conveyance of M.S. rods or Tor steel and binding wires and labour charges for straightening, cutting, bending etc. of M.S. rods or tor steel tying the grills and placing in proper position. (Test certificate should be furnished prior to execution and as directed by the Engineer-In-Charge). |
| 41 | Providing, fixing and placing of Tor steel (HYSD) Fe-500(RINL/SAIL/TATA/JINDAL STEEL/SHYAM STEEL) for RCC work in all floors of required diameter of approved quality with straightening, Cutting, bending, binding welding or jointing if necessary, bending, binding, tying the grills as required for R.C.C. works, providing fan hooks where necessary and hoisting, lowering and placing in proper position according to approved designs and drawings including cost, conveyance, loading, unloading, taxes of M.S. rods or Tor steel and binding wires of 18 to 20 gauge required for the work and cost of all labour, sundries, T & P and scaffolding complete in all respect as directed by the Engineer-in-Charge ( payment will be made according to the actual weight of M.S rod /Tor steel consumed in the work and no separate payment will be made towards weight of binding wires which is to be borne by the contractor at his own cost. |
| 42 | Providing, Fitting, Fixing of Tensile Fabric material of SION 900 gsm, Breaking Strength 4000N/5CM, TEAR STRENGTH 600/500N,FLAME RETARDANCY M2/B1, Temperature Resistance-30/70 degree C including M.S pipe required for framing of truss of Column pipe-200 mm, Arch 100mm, Spurting 100mm of TATA STEEL including cost of all materials, labour, T&P , taxes etc. required for the work complete. |
| 43 | Disposal of excess earth by mechanicalmeans/manually including cost of loading, unloading, transporting & spreading to a level surface complete in all respects including cost of all labours.tools & plant etc. to complete the work. |
| 44 | Extension of Boundry Wall : Earthwork in excavation in all kinds of soil upto 1.50mtr depth of foundation trenches for columns, basement, tie beams, walls and steps in following types of soil including moorum, hard stony earth, earth mixed with boulders, DI rocks etc but not requiring blasting with initial leads and lifts including dressing and leveling the bed sides up to required depth and depositing the excavated materials at places away from the work site with T&P for shoring, shuttering, dewatering if required etc. complete as per the drawing, design including cost of all labour, T&P etc. as required for the work complete as directed by the Engineer-in-charge. |
| 45 | Supplying and filling the Foundation & Plinth with clean coarse river sand of approved quality from approved quarry, laying in layers not exceeding 150mm thick, watering and ramming including cost, conveyance, royalty and cost of all labour, T&P etc. as required for the work complete as per direction of the Engineer-in-charge. |
| 46 | Providing and lying plain cement concrete of proportion (1:4:8) in foundation and floors using Portland Slag Cement(PSC) with 4 cm. Size black hard crusher broken granite stone metal and screened and washed sharp sand for mortar of approved quality from approved quarry, washed and cleaned including hoisting, lowering, laying concrete, ramming, watering and curing etc. complete to required levels laid in layers not exceeding 15 cm thick in each layer including cost, conveyance, loading, unloading, royalties and cost all labours, sundries, T & P required for the work including shoring, shuttering and dewatering if required including hire & running charges of water pump complete as per specification and direction of Engineer-in-charge. |
| 47 | Providing Fly Ash Brick masonry using fly ash bricks of size 25 cm. x 12 cm. x 8 cm. having crushing strength not less than 75 kg. Per. Sqr. Cm. in cement mortar of mix(1:6) with ordinary Portland slag cement(PSC) and screened & washed sand for mortar in foundation, plinth, basement and for ornamental flower beds, plinth moulding and similar such type of works with all necessary projections, splays cutting, circular moulding, corbelling, chamfering and similar such type of works, watering and curing etc. including cost, conveyance, loading, unloading, royalties and taxes of all materials, cost of all labour, scaffolding, sundries, T&P required for the works etc. complete in all respect as per specification and direction of Engineer-in-charge. |
| 48 | Providing Fly Ash Brick masonry using fly ash brick of size 23 cm. x 11 cm. x 8 cm. having crushing strength not less than 75 kg. Per. Sqr. Cm. in cement mortar of mix(1:6) with ordinary Portland slag cement(PSC) and screened & washed sand for mortar in superstructure including splays cutting, circular moulding, corbelling, chamfering and similar such type of works, watering and curing etc. including cost, conveyance, loading, unloading, royalties and cost of all labour, scaffolding, sundries, T&P required for the works etc. complete in all respect as per specification and direction of Engineer-in-charge. |
| 49 | Providing, lifting, hoisting and laying Reinforced cement concrete of different RCC structure in foundation level of M-250 grade as per approved designs and drawings having a minimum compressive strength (in work test) 250 Kg. / Square cm. in 15 cm. cubes at 28 days after mixing and test conducted in accordance with I.S. 516 using 12 mm. to 20 mm. size black hard crushed broken granite stone chips and screened and washed sharp sand for mortar of approved quality from approved quarry, washed and cleaned ( 20mm. size chips not to exceeds 25 % ) to be mixed in concrete mixture with Portland slag cement (PSC) including hoisting, lowering, laying and compaction concrete by using vibrators, watering and curing for 28 days, centering and shuttering then after dismantling and removing debris from the work site and finishing the exposed surface smooth providing grooves or beads wherever necessary including cost, conveyance, loading, unloading, royalties and cost of all labours, sundries, T & P required of the work etc. complete in all respect as directed by the Engineer-in-Charge. But excluding cost and conveyance of M.S. rods or Tor steel and binding wires and labour charges for straightening, cutting, bending etc. of M.S. rods or tor steel tying the grills and placing in proper position. (Test certificate should be furnished prior to execution and as directed by the Engineer-In-Charge). |
| 50 | Footing |
| 51 | Column |
| 52 | Plinth beam |
| 53 | Providing, fixing and placing of Tor steel (HYSD) Fe-500(RINL/SAIL/TATA/JINDAL STEEL/SHYAM STEEL) for RCC work in all floors of required diameter of approved quality with straightening, Cutting, bending, binding welding or jointing if necessary, bending, binding, tying the grills as required for R.C.C. works, providing fan hooks where necessary and hoisting, lowering and placing in proper position according to approved designs and drawings including cost, conveyance, loading, unloading, taxes of M.S. rods or Tor steel and binding wires of 18 to 20 gauge required for the work and cost of all labour, sundries, T & P and scaffolding complete in all respect as directed by the Engineer-in-Charge ( payment will be made according to the actual weight of M.S rod /Tor steel consumed in the work and no separate payment will be made towards weight of binding wires which is to be borne by the contractor at his own cost. |
| 54 | Providing Artistic Paint to the wall surface as per direction of the Enginner-In-Charge. |
| 55 | Landscape :Surface dressing of ground including removal of vegetation, grass, bushes and other rubbish, and making up undulations and inequalities not exceeding 15 cm in depth or height. The work includes disposal of rubbish within a lead of 50 m (at least 5 m away from the dressed area), complete as directed by the Engineer-in-Charge. |
| 56 | Supplying good earth from approved source including royalty, carriage up to 5 km, stacking at site and spreading the earth in layers of 300 mm thickness. The earth measured in stacks will be reduced by 20% for payment. The work includes levelling, dressing and finishing the surface, complete as directed by the Engineer-in-Charge. |
| 57 | Supplying sludge (good fertile sludge / silt) from approved source including royalty, carriage up to 5 km, and stacking at site. The sludge measured in stacks will be reduced by 8% for payment. The work includes loading, unloading and proper stacking at site, complete as directed by the Engineer-in-Charge. |
| 58 | Uprooting weeds from the trenched area after 10–15 days of flooding with water, including removal of all weeds and unwanted vegetation. The work includes disposal of uprooted vegetation outside the working area, breaking clods, and fine dressing of the ground surface. The item also includes cost of labour, materials, tools and tackles, complete as per the direction of the Engineer-in-Charge. |
| 59 | Planting of ornamental species of size 30\\" × 30\\" pit with 6'–7' height poly pack plants, including digging pits, removing all unserviceable materials and disposing outside the work area as directed by the Engineer-in-Charge. Supplying and filling pits with good garden soil mixed with well-decomposed cow dung manure in the ratio 4:1, including required quantities of fertilizers and pesticides. Supplying and planting specified saplings and carrying out maintenance works such as watering, weeding, application of fertilizers and pesticides, etc., including cost of labour, materials, tools and tackles, complete as per the instruction of the Engineer-in-Charge. |
| 60 | Supply and planting of slow growing ornamental species such as Asoka (Saraca asoca), Baula (Mimusops elengi), Bottle Brush (Callistemon lanceolatus), Neem (Azadirachta indica), Karanj (Pongamia pinnata), Debdaru (Polyalthia longifolia), Aonla (Emblica officinalis), Sunari (Cassia fistula) and Kanchan (Bauhinia variegata) in 30\\" × 30\\" × 30\\" pits with 6'–7' height poly pack plants etc. completed. |
| 61 | Supply and planting of shrub species (local varieties) such as Mandar (Hibiscus rosa-sinensis), Tagar (Tabernaemontana coronaria), Kaniar (Thevetia spp.), and Karabira (Nerium oleander) in pits of size 1' × 1' × 1'.etc. completed |
| 62 | Supply and planting of creepers / climbers / ground cover plants such as Jui (Jasminum officinale), Jai (Jasminum pubescens), and Madhumalati (Quisqualis indica) in pits of suitable size (about 1' × 1' × 1') etc. completed. |
| 63 | Furniture : Providing, supplying and placing for Conference Full Chair. SEAT/BACK ASSEMBLY: The back is made up of 1.2 ±0.1cm. thick hot-pressed plywood & seat is made up of 1.5 ±0.1cm. thick hot-pressed plywood measured as per QA method described in OCP-QLTA-P14-18 and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured foam lumbar support. The seat has extra thick foam on front edge to give comfort to popliteal area.*HIGH BACK SIZE 51.5 cm. (W) x 82.0 cm. (H), *FULL BACK SIZE 51.5 cm. (W) x 69.0 cm. (H), *SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D)HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 14 ± 2 kgf as per IS:7888 for 25% compression.· Armrest top is mounted on Armrest structure made of glass filled Nylon.· Armrest Top is PU moulded over glass filled Nylon insert.ARMRESTS (THRILL Executive CHAIR) : The 3-way adjustable armrest is is made of die-cast aluminium with buffing finish designed with the following features :· Up-Down adjustment–7 steps (7.0 ± 0.5cm range)· It has to & fro movement along with Swivel adjustment.CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following features:· 360° revolving type.· 3 position locking with anti shock mechanism. as per direction of E.I.C. |
| 64 | Providing, supplying and placing of Visitor Chair. SEAT ASSEMBLY: The seat assembly should be made up of 1.2 ±0.1cm. thick hot-pressed plywood , upholstered with fabric upholstery covers and moulded Polyurethane foam.SEAT SIZE: 47.0 cm. (W) x 48.0 cm. (D)BACK ASSEMBLY: The back asembly. should be made of powder coated (OFT 40-60 microns) tubular frame of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back should be upholstered using double layer spacer mesh fabric with high tenacity yarn.BACK SIZE : 46.5 cm. (W) x 60.5cm. (H)HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression.ARMRESTS: The one-piece armrests should be injection moulded from black Co-polymer Polypropylene. .TUBULAR FRAME: The powder coated (DFT 40-60.microns) tubular frame should be cantilever type & made of Ø2.54 ±0.03cm. x 0.2 ±0.016cm thick M.S.E.R.W. Tube. Overall Dimensions of ChairSeat Height - 46.5cm.Height - 93.5cm.Width & Depth of Chair as measured from pedestal - Width-61.0 cm and Depth-64.5 cm. |
| 65 | Supply of PARTO Three Seater Sofa Leather Overall Size : Width : 134cm Depth : 87cm Height : 76cm Seating Height : 39.5cmSTITCHING: THREAD : Poly Proplin. LEATHER/PVC/FABRIC: PVC. Thickness (mm) : 0.9 Weight (GSM) : 575as per direction of E.I.C. |
| 66 | Supply of PARTO Single Seater Sofa Leather Overall Size : Width : 92cm Depth : 87cm Height : 76cm Seating Height : 39.5cmSTITCHING: THREAD : Poly Proplin. LEATHER/PVC/FABRIC: PVC. Thickness (mm) : 0.9 Weight (GSM) : 575 |
| 67 | Providing, supplying and placing of Mid Back Chair. SEAT ASSEMBLY: The seat is made up of 1.5±0.1 cm thick hot-pressed plywood upholstered with fabric and moulded polyurethane foam.SEAT SIZE: 51.8cm (W) x 49.7cm (D) BACK ASSEMBLY: The Back is injection moulded in glass filled Polypropylene which is 2 upholstered with Mesh fabric. The back consist of adjustable Lumbar support made of injection moulded Polypropylene having an adjustment of 5.0 10.1 cm.BACK SIZE: 47.9 cm(W) x 66.9 cm (H)HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane seat foam is moulded with density 45+/-2 kg/m and hardness 14 ± 2 kgf as per IS:7888 for 25% compression.ARMRESTS (ADJUSTABLE):The height adjustable armrest is made of Polypropylene and can be adjusted to 6.010.1cm height it also has swivel and To and Fro adjustment with moulded PU armtopACTIVE BIO-SYNCHRO MECHANISM: The adjustable tilting mechanism is designed with the following features360° revolving type Front-pivot for tilt with feet resting on ground & continuous lumber support ensuring more comfortTill tension adjustment can be operated in seating position5 position Tilt limiter giving option of variable sit angle to the chairSeat/back tilting ratio of 1:2 The mechanism housing is made up of HPDC Aluminium & black powder coated (DFT 40 to 60 micron)as per direction of E.I.C. |
| 68 | Providing and Supplying of Coffee Table 25mmX50mm CRC pipe (Powder Coated) 600mm/1200mm Height 450mm. 12mm toughened glass top colour- as per E.I.C. |
| 69 | Providing and Supplying of Storwel plain shall have an overall size of 916mm(W)x486mm(D)x1981mm(H) with welded construction. It should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. The Storwel Plain should have a Mazak handle and Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour options and shelving options shall be available. |
| 70 | Recessed wiring to light point / first light of group control/ call bell point/ exhaust fan point /wall fan point with 1.5 sq.mm FRLSH PVC insulated single core multistrand copper conductor of ISI marked in 20 mm dia non-metalic PVC conduit with 6 Amp, 250 V clip in type switch ISI marked and ceiling rose ISI marked mounted on G.I modular box with face plate & cover of suitable size , with 1.5 sq.mm FRLSH PVC insulated single core multistrand copper conductor as earth wire including all accesories and connection as per direction of Engineer in Charge. (Make of wire Finolex /Polycab/ Anchor / Havells/KEI/Eq) (Make of modular box,cover,switch & socket-Legrand Arteor/schneider Zencelo/Panasonic Vision/Eq) |
| 71 | GROUP-A |
| 72 | GROUP-B |
| 73 | GROUP-C |
| 74 | Recessed wiring to secondary light point looped from primary light point with 1.5sqmm FRLSH PVC insulated single core multistrand copper conductor of ISI marked with 20mm dia non-metallic PVC conduit with 1.5sqmm FRLSH PVC insulated single core multistrand copper conductor for running earth including 3 plate ISI marked Ceiling rose with all accessories & connection as per direction of Engineer-in-charge. (Make of wire KEI /Polycab/ Anchor / Havels/Eq) Average Length: 3 mtr |
| 75 | Recessed wiring to ceiling fan point with 1.5 sqmm FRLSH PVC insulated single core multistrand copper conductor of ISI marked with 20mm dia non-metallic PVC conduit with 6Amp 250V Modular Switch,Stepped type Moudular Regulator, Base & Cover with 1.5sqmm FRLSH PVC insulated single core multistrand copper conductor for running earth including all accessories & connection as per direction of Engineer in charge. (Make of wire KEI /Polycab/ Anchor / Havels/Eq) Group c |
| 76 | Recessed wiring to Twin control light point with 1.5 sq.mm FRLSH PVC insulated single core multistrand copper conductor of ISI marked in 20 mm dia non-metalic PVC conduit with 6Amp, 250 V clip in type 2way switch ISI marked and ceiling rose ISI marked mounted on G.I modular box with face plate & cover of suitable size , with 1.5 sq.mm FRLSH PVC insulated single core multistrand copper conductor as earth wire including all accesories and connection as per direction of Engineer-in-charge. (Make of wire KEI /Polycab/ Anchor / Havels/ Finolex/Eq) Group C |
| 77 | Supply and fixing of 5 / 6 amp socket outlet with 6 Amp, 250 V clip in type modular switch ISI marked mounted on G.I moular box with face plate & cover of suitable size including all accesories and connection on same switch board as per direction of Engineer-in-charge. |
| 78 | Supply and fixing of 2 x 6 amp socket outlet controlled by 2 nos 6Amp, 250 V clip in type switch ISI marked mounted on single G.I moular box with face plate & cover of suitable size including all accesories and connection on separate board as per direction of Engineer-in-charge. |
| 79 | Receass wiring for circuit/submain wiring with the following mentioned size PVC FRLS insulated, copper conductor, single core cable Make- Finolex/Anchor/Polycab/HAVELLS/RR KABLE/KEI in recessed HMS FRLS PVC conduit of mentioned size Make-AKG/BEC/Precision/Norpak/ Anchor/Kinjal as required as per direction of Engg.-in-Charge. 2 nos single core 1.5 sq. mm copper wire for phase and neutral and 01 no of single core 1.5 sq. mm copper wire for earth continuty conductor. In 20 mm dia non metallic heavy duty conduit (LDB to LSB/LIGHT CKT)(2X1.5+1X1.5) |
| 80 | Receass wiring for circuit/submain wiring with the following mentioned size PVC FRLS insulated, copper conductor, single core cable Make- Finolex/Anchor/Polycab/HAVELLS/RR KABLE/KEI in recessed HMS FRLS PVC conduit of mentioned size Make-AKG/BEC/Precision/Norpak/Anchor /Kinjal as required as per direction of Engg.-in-Charge.2 nos single core 2.5 sq. mm copper wire for phase and neutral and 01 no of single core 1.5 sq. mm copper wire for earth continuty conductor in 20 mm dia non metallic heavy duty conduit.(BDB to LSB/LIGHT CKT/5A PLUG/UPS POINT ) (2X2.5+1X1.5) |
| 81 | Supply, Installation, Testing and Commissioning of Plastic body Exhaust fan 200 mm sweep 900 rpm with louvers of approved make with all other required materials & labour complete as per the direction of Engineer-in-Charge. (Make- Havells/ Crompton/ Usha/ Orient/Bajaj). |
| 82 | Supply, Installation, Testing and Commissioning of 1200 mm sweep Decorative ceiling fan including wiring the down rods of standard length (upto 30 cm) with 1.5 sq.mm FR PVC insulated single core multiatrand copper conductor etc of approved make with all other required materials & labour complete as per the direction of Engineer-in-Charge. (Make- Havells SS390 /Crompton /Usha/Orient /Bajaj). |
| 83 | SITC of energy efficient LED tube light fittings with decorative alluminium batten and LED tube light having power rating not more than 20 watt and lumen output not less than 2000 lumen complete with electronic driver and all other accessories with diffuser of approved make with all other required materials & labour complete as per the direction of Engineer-in-Charge. (Make: Panasonic/LT/ Havells /Philips/Wipro /K lite/Crompton/Bajaj). |
| 84 | SITC of energy efficient LED tube light fittings with decorative alluminium batten and LED tube light having power rating not more than 10 watt and lumen output not less than 2000 lumen complete with electronic driver and all other accessories with diffuser of approved make with all other required materials & labour complete as per the direction of Engineer-in-Charge. (Make: Panasonic/LT/ Havells /Philips/Wipro /K lite/Crompton/Bajaj). |
| 85 | SITC of 12 watt LED Ceiling Recessed mounted Downlight with Low depth Aluminium (99% Purity) Heat Sink, available in Round and Square shape. PC diffuser in white powder coated finish with independent electronic low THD (<10%) LED driver of approved make with all other required materials & labour complete as per the direction of Engineer-in-Charge. (Make: Panasonic/LT/ Havells /Philips/Wipro /K lite/Crompton/Bajaj). |
| 86 | SITC of 3 watt LED Ceiling Recessed mounted spot light in different Colour Aesthetically designed lens based of approved make with all other required materials & labour complete as per the direction of Engineer-in-Charge. (Make: Panasonic/LT/ Havells /Philips/Wipro /K lite/Crompton/Bajaj). |
| 87 | SITC of 36 watt 2 x 2 Celing light of approved make with all other required materials & labour complete as per the direction of Engineer-in-Charge. (Make: Panasonic/LT/ Havells /Philips/Wipro /K lite/Crompton/Bajaj). |
| 88 | SITC of 18 watt LED Ceiling Surface mounted Downlight with Low depth Aluminium (99% Purity) Heat Sink, available in Round and Square shape. PC diffuser in white powder coated finish with independent electronic low THD (<10%) LED driver of approved make with all other required materials & labour complete as per the direction of Engineer-in-Charge. (Make: Panasonic/LT/ Havells /Philips/Wipro /K lite/Crompton/Bajaj). |
| 89 | Supplying, installation and commissioning of 35W LED post top light luminaries having Versatile pressure die-cast aluminium IP66 with high power LED as light source to be fixed on the ends of pole etc complete with connection as required for the work and as per direction of Engineer-in-Charge.(Make: Havells Ruby /K- Lite/ BAJAJ/ CG/Jaquar). |
| 90 | Supply, installation, testing & commissioning of IP 65 LED street Light of 90 W Capacity 6000K Colour temperature with pressure die-cast Aluminium body having in built electronic driver which have 50000 burning hour road way luminaries of approved make complete with all materials & labour as required as per the direction of Engineer-in-Charge. |
| 91 | Supplying, Installation, Testing & Commissioning of All-in-One Desktop-13th Gen., Intel Core i-5 processor, windows-11, Ms Office, 16 GB Ram, 1TB SSD, 23.8’’ Display, Front Camera with one year antivirus & 600 VA UPS of approved make complete with all materials & labour as required as per the direction of Engineer-in-Charge.( Make - HP/ Dell) |
| 92 | Supplying, Installation, Testing & Commissioning of Dell Inspiron 15 Notebook Laptop (Intel i5-16 GB/512 GB SSD/ Integrated/ Windows 11/MS Office/ Full HD), 39.62 cm -15.6 inch, Platinum Silver with one year antivirus of approved make complete with all materials & labour as required as per the direction of Engineer-in-Charge.( Make - HP/ Dell) |
| 93 | Supplying, Installation, Testing & Commissioning of Laser Jet Duplex Printer Auto- Duplex print, Copy & Scan,Touch Screen Display, Inbuilt Dual band WI-FI with USB port of approved make complete with all materials & labour as required as per the direction of Engineer-in-Charge.( Make - HP/ Dell) |
| 94 | Supplying, Installation, Testing & Commissioning of HP Ink Tank 419 All-in-one Wifi Colour Printer Style Name: Wifi , 15K Black and 8k Colour Prints,Brand HP Connectivity Technology USB, Wi-Fi ,Printing Technology Inkjet, Special Feature Wireless, Colour Black,Model Name Ink Tank Wireless 419 Printer Output Colour, Maximum Print Speed (Colour) 5 ppm, Max Print speed Monochrome 8 ppm, Item Weight 4.67 Kilogramsof approved make complete with all materials & labour as required as per the direction of Engineer-in-Charge. ( Make - HP/ Dell) |
| 95 | Supplying, Installation, Testing & Commissioning of Digital Camera CAMERA : Aspect Ratio - 4:3, Photo Sensor Technology : CMOS, Supported File Format : JPEG, Image Stabilisation : Digital , Optical Zoom : 1 x, Photo Sensor Resolution : 20 MP ,Effective Still Resolution :20 MP, JPEG Quality Level : Fine, Maximum Image Size : 20 MP, Total Still Resolution :20 MP , Maximum Aperture : 3.5 Millimeters, Metering Description: Center Weighted, Photo Sensor Size : 1-inch fps, UHD 4K recording up to 30p is supported for cris, Versatile 20.9MP resolution, Hybrid autofocus system uses both phase-detection and contrast-detection methods, Lens Type : Telephoto, Camera Lens : 50 millimeters, Minimum Focal Length : 16 Millimeters, Photo Filter Thread Size : 46 Millimetres Make- Nikon / Canon/ Fuji/ SonyTRIPOD STAND: Foldable Tripod Stand with Phone Holder & 360° Ball Head, 5kg Load Capacity, Aluminum Alloy Legs with Rubberized Feet & Flip Locks, Carry Bag, for Photo & Video Shoots. Make- Digitech/ Bosch/BoxtudioWater Resistant Bag : Water Resistant Camera Bag/Case Shoulder Strap Space for Photography Lens and Accessories CompatibleMicro HDMI Camera ( Live View / Playback on TV) : Micro HDMI To HDMI Cable, 4K 60Hz, 5Meter , Adapter Ethernet Audio Return Compatible for all cameraSD Card : SanDisk SDSDXXD-128G-GN4IN Extreme Pro 128 GB SDHC Class 10 200 MB/s Memory Card Compatible with Camera of approved make complete with all materials & labour as required as per the direction of Engineer-in-Charge. |
| 96 | Suppy, installation, testing & commissioning of Aquaguard Cooler-Cum-Purifier with Standard Accessories of approved make complete with all materials & labour as required as per the direction of Engineer-in-Charge. Make - Eureka Forbes (AGCCP) / Equivalent |
| 97 | Suppy, installation, testing & commissioning of SS Table with all materials & labour as required as per the direction of Engineer-in-Charge. |
| 98 | Supply, fabrication, transportation, installation, testing and commissioning of LED Backlit Glow Sign Board of approved design and size, consisting of MS square tube frame (minimum 25mm x 25mm x 1.6mm thick) duly welded, treated with anti-rust primer and finished with enamel paint backing with 3mm thick Aluminium Composite Panel (ACP) sheet, front face with 3mm thick translucent acrylic sheet, complete with high brightness IP65 rated SMD LED modules (minimum 1.2W each) with uniform illumination, suitable electronic driver (SMPS) conforming to 220–240V AC input and 12V DC output, internal FRLS copper wiring, weatherproof junction box, earthing provision, fixing arrangement with MS brackets, anchor fasteners, stainless steel screws, sealing with silicone for weatherproofing, including high resolution digitally printed CNC cut acrylic lettering as approved, complete in all respects and as directed by Engineer-in-Charge. (The board is to be fixed to ground with 50mm dia G.I. pipe & required Cement Concrete) |
| 99 | Earthing with copper earth plate 600 mm x 600mm x 3.15 mm thick ISI marked including accessories and providing masonary with cover plate having loccking arrangement and watering pipe etc with charcoal and salt of approved make complete with all materials & labour as required as per the direction of Engineer-in-Charge. |
| 100 | Supplying and laying 25 mm x 6 mm Copper earth strip ISI marked at 0.5 meter below ground level as strip earth electrode including soldering of approved make complete with all materials & labour as required as per the direction of Engineer-in-Charge. |
| 101 | Supplying, storing, laying, testing and commissioning of 2c x 6 Sq. mm armoured Aluminium Cable direct in ground including excavation, sand cushining protective covering and refilling the trench of approved make complete with all materials & labour as required as per the direction of Engineer-in-Charge. Please Enable Macros to View BoQ information |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
