|
| 1 | B/R PORTION:- M&L for rendering 20 mm thick on concrete surface, roof top surfaces in cement mortar ( 1:4) including water proofing compound and finished even & smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge. Note : Supply only WPC will be measured and paid separately. |
| 2 | M&L for 40 mm thk PCC (1:2:4) Bo using 12.5 mm graded stone aggregate as in levelling padding course over RCC roof surface including rounded or chamferred on edges etc., with approved water proofing compound all as per manufacturer's instructuions on the roof surface to achieve requisite slope complete all as specified and as directed by the Engineer-in-Charge.Note :- Supply only water proofing compound shall be measured & paid separately |
| 3 | M&L for applying evenly a tack coat of in dustrial bitumen 85/25 at the rate of 1.2 kg per sq.m including cleaning surfaces complete all as specified and as directed by the Engineer-in-Charge. |
| 4 | M&L for APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified and as directed by the Engineer-in-Charge. |
| 5 | M&L for Chipping of slab/columns/ beams/chajjas /parapet /roof projection/ balcony/ staircase and removing loose mortar with chisel hammer without much impact on concrete surface, clean the surface by sand blasting the surface using river sand with minimum of 6 kg pressure at the nozzle or air blow by electric pressure blower by mechanical compressor, cleaning the exposed reinforcement with wire brushes etc and disposal of debris for all lead and lifts complete all as specified and as directed by the Engineer-in-Charge.Note :- Scaffolding/ temporary support structure required to support the members / structure during strengthening shall be include in this items |
| 6 | M&L for applying bond coat cum waterproofing on the prepared old surface of concrete/masonry to receive new polymer mortar/polymer modified mortar with two coats of Slurry- @ approximately 2- 2.5 m2 / litre depending on substrate porosity of Fosroc Nitobond SBR300 or equivalent Equivalent etc as per manufacturer specifications. Laying of reinstatement readymade plaster/polymer mortar shall be completed within the overlay time of bonding coat. This bond coat act as bonding agent between old and new concrete complete all as specified and as directed by the Engineer-in-Charge.Note :The rate quoted by contractor shall include cleaning of surface, application as per instruction and scaffolding upto 20mtr height. |
| 7 | M&L for applying to the damaged concrete portion of slab / columns / beams / chajjas/ parapet /roof projection/ balcony/ staircase with single component, fiber reinforced, dual shrinkage- compensated thixotropic, cementitious patch repair mortar Sika monotop 122F (having the technical parameters mentioned in material specifications) capable of applying up to 20-30 mm thick in double layer initially by hand and finishing with troweled carefully compacting the same around the rebar and finishing to bring it in line with existing concrete surface with an average specified thickness complete all as specified and as directed by the Engineer-in-Charge. Note :- Scaffolding/ temporary support structure required to support the members / structure during strengthening shall be include in this items |
| 8 | Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar complete all as specified and as directed by the Engineer-in-Charge. Note : Work will be in patches or in bulk |
| 9 | M&L for Granite of black / green / imperial red (colour as approved by GE) of any type machine cut as in shelves/steps/counter tops, 20 mm thick, set and jointed in cement slurry over & including screed or 15 mm thick rendering in cement mortar (1:4) and pointed in cement mixed with pigment to match the shade of slab or with suitable adhesive for fixing on unpolished kota stone slabs and including rubbing, cutting and mirror type polishing and bull nose on exposed sides complete all as specified and as directed by the Engineer-in-Charge.Note : Single piece should be used in steps/cills/jambs/shelves. |
| 10 | M&L for Machine cut kota stone slab flooring 20-25mm thick over, laid over cement screed base , jointed and pointed with grey cement slurry mixed with pigment over 20mm thick cement mortar 1:6 screed bed to match the shade of the slab including rubbing and polishing and single piece complete all as specified and as directed by the Engineer-in-Charge. Note : Work will be in patches or in bulk |
| 11 | M&L for Machine cut kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar over 10 mm thick cement plaster 1:3 jointed and pointed with grey cement slurry mxed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed by the Engineer-in-Charge. |
| 12 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and as directed by the Engineer-in-Charge. |
| 13 | Demolition of Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and as directed by the Engineer-in-Charge. |
| 14 | M&L for 75mm thk cement concrete 1:4:8 type D2 using 40mm graded stone aggregate as in sub base of flooring/hard standing complete all as specified and as directed by the Engineer-in-Charge. |
| 15 | M&L for 25mm thk PCC 1:2:4 type B0 using 12.5mm graded stone aggregate as in sub base of floors & finishing the surface even & smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge. |
| 16 | M&L for Non Skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm,including 15mm screed bed in CM 1:6 in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed by the Engineer-in-Charge. |
| 17 | M&L for non skid tiles coloured 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. in any pattern of light & dark tiles as approved, set and jointed in neat cement slurry and pointed in white or coloured cement to match, in floors etc. over & including 15 mm thick screed in cement mortar (1:6) over and pointed in white cement with pigment to match the colour of tiles complete all as specified and as directed by the Engineer-in-Charge. |
| 18 | M&L for Glazed ceramic glossy finish tiles coloured in vertical surface 450X300X7mm in any pattern of light & dark/ highlighters tiles etc as approved, on vertical surfaces such as in skirting/dado etc, set and jointed in cement slurry over & including 10 mm thick rendering in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified and as directed by the Engineer-in-Charge. |
| 19 | S&F in repair CP soap dish standard size complete all as specified and as directed by the Engineer-in-Charge. |
| 20 | Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and as directed by the Engineer-in-Charge. |
| 21 | S&F 75mm bore PVC (SWR) single socketed in any length with rubber ring joints & fixed to walls complete all as specified and as directed by the Engineer-in-Charge. |
| 22 | S&F 110mm bore PVC (SWR) single socketed in any length with rubber ring joints & fixed to walls complete all as specified and as directed by the Engineer-in-Charge. |
| 23 | S&F in repair, 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed by the Engineer-in-Charge. |
| 24 | S&F in repair, PVC (SWR) bends of 75mm bore setting & jointing with solvent cement complete all as specified and as directed by the Engineer-in-Charge. |
| 25 | All as per item No. 24.00 here-in-before above but of 110mm bore. |
| 26 | S&F 75 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints laid in floors or trenches complete all as specified and as directed by the Engineer-in-Charge. |
| 27 | S & F 110 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints laid in floors or trenches complete all as specified and as directed by the Engineer-in-Charge. |
| 28 | S&F in repair, PVC (SWR) cowl of 75mm bore setting & jointing with solvent cement complete all as specified and as directed by the Engineer-in-Charge. |
| 29 | S&F in repair, PVC (SWR) cowl of 110mm bore setting & jointing with solvent cement complete all as specified and as directed by the Engineer-in-Charge. |
| 30 | S&F in repair for PVC (SWR) floor trap 75mm diameter of outlet, plain with grating including jointing with solvent cement incl jointing to waste pipe fixed in cement concrete type 1:2:4 B-1 using 20mm graded stone aggregate complete all as specified and as directed by the Engineer-in-Charge. |
| 31 | S&F in repair for PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and as directed by the Engineer-in-Charge. |
| 32 | S&F 600x450mm size bevellled edge mirror 5.5mm thick of selected quality glass mounted on 6mm thick AC building or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers including taking down old unserviceablecomplete all as specified and as directed by the Engineer-in-Charge. |
| 33 | S&F in repairs 15mm bore cast copper alloy chromium plated bib tap fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe complete all as specified and as directed by the Engineer-in-Charge. |
| 34 | S&F in repair brass chromium plated Health faucet with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and as directed by the Engineer-in-Charge. |
| 35 | S&F in repair corner glass shelf size 300 mm radius with and including bracket and glass complete set etc complete all as specified and as directed by the Engineer-in-Charge. |
| 36 | S&F in repairs 15mm dia Bib tap (2 in 1 type) of brass, chromium plated fancy type glossy finish fixed to wall complete all as specified and as directed by the Engineer-in-Charge. Make :- cera cat part No F-1015163 or Jaquar/ Hindware/ Prayag/ Parryware or equivalent model as approved by GE. |
| 37 | S&F in repair pillar tap, cast copper alloy fency type chromium plated screwed down high, pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts screwed for iron pipe and fixed to 15mm bore of pipe complete all as specified and as directed by the Engineer-in-Charge. |
| 38 | S&F in repairs tubler towel rail brass chromium plated 20mm dia, D type 60cm long between flanges complete all as specified and as directed by the Engineer-in-Charge. |
| 39 | S&F in repair wash basins vitreous china, white /coloured flat back size 550 x400mm fixed including bracket complete all as specified and as directed by the Engineer-in-Charge. |
| 40 | S&F 15mm bore of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors specified. with all fittings such as brasss Tee, brass elbows, brass sockets, brass unions, plugs, short lenghts etc. and fixed complete to walls and ceilings or laid in floors concealed or open of any length including taking down or up existing GI tubing & connections complete all as specified and as directed by the Engineer-in-Charge. |
| 41 | S&F in repairs vitreous china wash down water closet pedestal pattern pan white with trap including connection to existing out joint pipe, flushing pipe or Cistern, antisyphonage pipe, including making, etc complete including making good to floor etc complete all as specified and as directed by the Engineer-in-Charge. |
| 42 | S&F in repair PVC low level white flushing cistern syphonic action type 10 ltrs capacity incl flush pipe 32 mm dia incl PVC connection 450 mm long complete all as specified and as directed by the Engineer-in-Charge. |
| 43 | S&F in repairs PVC connection 15mm size with PTMT nuts and polythene washers of 450mm length complete all as specified and as directed by the Engineer-in-Charge. |
| 44 | S&F in repair Swivel shower rose 75mm size with arm 195mm long with bend of 45 degree with flange of PTMT any colour fixed complete all as specified and as directed by the Engineer-in-Charge.. |
| 45 | S&F in repair Glass shelf size 600 mm long with and including bracket and glass complete set etc. complete all as specified and as directed by the Engineer-in-Charge. Make :- cera cat part No. F5001114 or Jaquar/ Hindware/ Prayag/ Parryware or equivalent model as approved by GE. |
| 46 | S&F in repair 15mm bore angle valves cast copper alloy screwed down high pressure with crutch or butter fly handles screwed both ends for iron pipe or for union complete all as specified and as directed by the Engineer-in-Charge. |
| 47 | S&F in repair 15mm fancy type, chromium plated with long shank and cup (concealed type Stop valves, cast copper alloy screwed pressure, with crutch of butterfly handle, screwed both ends for iron pipe for unions and fixed complete all as specified and as directed by the Engineer-in-Charge. |
| 48 | Taking down chowkhats or frames (without taking off shutters from the frame) n. exc 1.5 Sqm incl cutting holes and making good reqd shape for hold fast block for new frame complete all as specified and as directed by the Engineer-in-Charge. |
| 49 | Providing and fixing powder coated 50 microns extruded aluminium in 3 Tier Track Sliding Windows/ glazing, with frame of section 100x44-45x1.30mm, track of size 100x38.10x1.30 & shutters made of size 32x18x1.3mm, with and including 4.5 mm thick tinted sheet glass selected quality fixed in 2 shutters and stainless steel wire gauge 0.36mm nominal dia of wire and average width of aperture 1.40mm in one shutter and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beeds 20mm size and also including powder coated 150mm handle with built in locking system for each leaf complete all as specified and as directed by the Engineer-in-Charge. |
| 50 | Providing and fixing powder coated 50 microns extruded aluminium Windows/glazing, window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including 4 mm thick tinted glass, necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21100mm long (2 no.) suitable handle (1no.) complete all as specified and as directed by the Engineer-in-Charge. |
| 51 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and as directed by the Engineer-in-Charge. Note:- (i) M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). (ii) For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extrapayment on this account shall be made. |
| 52 | S&F 30mm thick Factory made single extruded WPC (Wood PolymerComposite) solid plain flush door shutter comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunkS.S screws, complete all as specified and as directed by the Engineer-in-Charge and including supply and fixing following items:-(a) Stainless Steel (304 Grade) Finished Butt Hinges 125mm - 3 Nos per leaf(b) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 Nos per leaf(c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 Nos per leaf |
| 53 | Taking down chowkhats or frames (without taking off shutters from the frame) exc 1.5 Sqm and n. exc 4.00 Sqm incl cutting holes and making good reqd shape for hold fast block for new frame complete all as specified and as directed by the Engineer-in-Charge. |
| 54 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and as directed by the Engineer-in-Charge. Note:- (i) M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). (ii) For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extrapayment on this account shall be made. |
| 55 | S & F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50 x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and as directed by the Engineer-in-Charge. Note:- (i) M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately) (ii) For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extrapayment on this account shall be made. |
| 56 | S&F 35mm thick Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type skelton door shutter comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter open rebated and divided to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutter as specified in SSR-91 Pt-I section 8 clause 8.20 (a) kiln seasoned and chemically pressure treated all as specifeid including stainless steel 304 grade wire cloth ( 0.36mm nominal dia of wire and average width of aperture 1.40 mm ) complete all as specified and as directed by the Engineer-in-Charge and including supply and fixing following items:-(a) Stainless Steel (304 Grade) Finished Butt Hinges 125mm - 3 nos per leaf(b) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 nos per leaf(c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 nos per leaf(d) Stainless Steel (304 Grade) Finished Sliding Door Bolt / Aldrop 16x3000mm - 1 nos per leaf(e) Stainless Steel (304 Grade) Finished Floor Door Stooper - 1 nos per leaf Please Enable Macros to View BoQ information |
| 57 | S&F 35mm thick Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type skelton door shutter comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter open rebated and divided to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutter as specified in SSR-91 Pt-I section 8 clause 8.20 (a) kiln seasoned and chemically pressure treated all as specifeid including stainless steel 304 grade wire cloth ( 0.36mm nominal dia of wire and average width of aperture 1.40 mm ) complete all as specified and as directed by the Engineer-in-Charge and including supply and fixing following items:-(a) Stainless Steel (304 Grade) Finished Butt Hinges 125mm - 3 nos per leaf(b) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 nos per leaf(c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 nos per leaf(d) Stainless Steel (304 Grade) Finished Sliding Door Bolt / Aldrop 16x3000mm - 1 nos per leaf(e) Stainless Steel (304 Grade) Finished Floor Door Stooper - 1 nos per leaf Please Enable Macros to View BoQ information |
