|
| 1 | Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. |
| 2 | 12 mm cement plaster of mix : |
| 3 | 1:4 (1 cement: 4 River sand) |
| 4 | 6 mm cement plaster of mix : |
| 5 | 1:3 (1 cement : 3 River sand) |
| 6 | Providing and laying Hollow Cement concerte hollow walling 200mm thick consisting of Hollow block of size 400x200x200 mm of mix 1:3:6 (1 Cement, 3 Pulverised sand, 6 grade stone aggreagete 10mm nominal & down size laid in cement mortar 1:6 ( 1 Cement :6 Pulverised sand) upto floor-V level. |
| 7 | Providing and laying Hollow Cement concerte hollow walling 100mm thick consisting of Hollow block of size 400x100x200 mm of mix 1:3:6 (1 Cement, 3 Pulverised sand, 6 grade stone aggreagete 10mm nominal & down size laid in cement mortar 1:6 ( 1 Cement :6 Pulverised sand) upto floor-V level. |
| 8 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : |
| 9 | New work (two or more coats) over and including water thinnable priming coat with cement primer |
| 10 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). |
| 11 | Superior hard wood Cat-I (A) (Paduak) |
| 12 | Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately) |
| 13 | Superior hard wood Cat-I (A) (Paduak) |
| 14 | 35 mm thick |
| 15 | Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. |
| 16 | Superior hard wood Cat-I (A) (Paduak) |
| 17 | 30 mm thick |
| 18 | Providing and fixing factory made P.V.C. door frame of size 50x47 mm with awall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineer- in-Charge. |
| 19 | Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer's specification & drawing. |
| 20 | 30 mm thick plain PVC door shutters |
| 21 | Providing and fixing in wall lining flat pressed three layer (medium density) particle board or graded wood Pre-laminated one side decorative lamination and other side balancing lamination Grade I, Type II, IS : 12823 marked, including priming coat on unexposed arrangement and screws etc. complete : |
| 22 | 12 mm thick |
| 23 | Cement concrete flooring 1:2:4 (1 cement : 2 pulverised sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. |
| 24 | 40 mm thick with 20 mm nominal size stone aggregate |
| 25 | Providing and fixing plain multipurpose cement board(Hight pressure steam cured) with suitable screws for cement particle board in ceiling etc. complete (frame work to be paid seperatately). |
| 26 | 6 mm thick Cement fiber board as per IS: 14862 |
| 27 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 28 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. |
| 29 | Size of Tile 600x600 mm |
| 30 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 pulverised sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 31 | Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: |
| 32 | Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm) |
| 33 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. |
| 34 | In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 35 | Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 36 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 37 | Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size). |
| 38 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : |
| 39 | 300x16 mm |
| 40 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : |
| 41 | 150x10 mm |
| 42 | 100x10 mm |
| 43 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : |
| 44 | 125 mm |
| 45 | 100 mm |
| 46 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. |
| 47 | Single rubber stopper |
| 48 | Applying priming coat: |
| 49 | With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) |
| 50 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : |
| 51 | Two or more coats on new work |
| 52 | Painting with black anti-corrosive bitumastic paint of approved brand and manufacture to give an even shade : |
| 53 | Two or more coats on new work |
| 54 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: |
| 55 | White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap |
| 56 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 57 | Providing and fixing plain bend of required degree. |
| 58 | 75 mm dia |
| 59 | Sand cast iron S&S as per IS -1729 |
| 60 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall |
| 61 | 15 mm dia nominal bore |
| 62 | Providing and fixing brass stop cock of approved quality : |
| 63 | 15 mm nominal bore |
| 64 | Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. |
| 65 | Centering and shuttering including strutting, propping etc. and removal of form for |
| 66 | Foundations, footings, bases of columns, etc. for mass concrete |
| 67 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. |
| 68 | Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 69 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement: 1.5 pulverised sand (zone-III)derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 70 | Finishing walls with water proofing cement paint of required shade : |
| 71 | Old work (one or more coats applied @ 2.20 kg/10 sqm) over priming coat of primer applied @ 0.80 litrs/10 sqm complete including cost of Priming coat. |
| 72 | Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : |
| 73 | Ridges plain (500 - 600mm) |
| 74 | Providing and fixing powder coated aluminium work (minimum thickness of powder coating 50 micron) consisting of tee/ angle sections, of approved make conforming to IS : 733 in frames of false ceiling including aluminium angle cleats with necessary C.P. brass/ stainless steel sunk screws, aluminium perimeter angles fixed to wall with stainless steel rawl plugs @ 450 mm centre to centre and fixing the frame work to G.I. level adjusting hangers 6 mm dia. with necessary cadmium plated machine screws all complete as per approved architectural drawings and direction of the Engineer-in-charge (level adjusting hangers, ceiling cleats and expansion hold fasteners to be paid for separately). |
| 75 | Providing and fixing 6 mm dia. G.I. level adjusting hangers (upto 1200mm length), fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40x3mm size 60 mm long and stainless steel expandable dash fastener of 12.5 mm dia and 50 mm long, complete as per direction of Engineer-in-charge. |
| 76 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. |
| 77 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : |
| 78 | Of area 3 sq. metres and below |
| 79 | Dismantling cement asbestos or other hard board ceiling or partition walls including stacking of serviceable materials and disposal of unserviceable materials within 50 metres lead. |
| 80 | Providing & fixing White vitreous china water closet squatting pan (Indian type) along with \\"S\\" or \\"P\\" trap including dismantling of old WC seat and \\"S\\" or \\"P\\" trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i/c malba, all complete as per the direction of Engineer-in charge. |
| 81 | Orissa pattern W.C Pan of size 580x440 mm |
| 82 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : |
| 83 | 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources: 4 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 84 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. |
| 85 | Electric resistance or induction butt welded tubes |
| 86 | Providing valleys of 90 cm wide overall in plain aluminium sheet, with nuts & washers etc. i/c making necessary connection with rain water pipes. |
| 87 | 1.00 mm thick |
| 88 | ELECTRICAL WORKS |
| 89 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC Conduit, with piano type switch, suitable size PVC box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. |
| 90 | Group C |
| 91 | Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC Conduit, with 2 way piano type switch, suitable size PVC box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. |
| 92 | Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC Conduit, alongwith 1 No 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. |
| 93 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC Conduit as required. |
| 94 | 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire |
| 95 | 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire |
| 96 | 2 X 6 sq. mm + 1 X 6 sq. mm earth wire |
| 97 | Supplying and fixing Suitable PVC box on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps socket outlet and 15/16 amps piano type switch, connection, painting etc. as required.Make anchor/Polycab/Havells. |
| 98 | Supplying and fixing Suitable PVC box on surface or in recess, including providing and fixing 3 pin 5/6 amps socket outlet and 5/6 amps piano type switch, connection, painting etc. as required.Make anchor/Polycab/Havells. |
| 99 | Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required |
| 100 | Supplying, Installation, testing and commissioning of ASHLOK make SEE brand safe earthing electro Type-19, 50mm dia, length 2 meters and inner space to be filled with crystalline conductive mixture including filling up with electrode and providing masonry enclosure with cover plate having locking arrangements etc. as required. |
| 101 | Proving and fixing 25mm x 5mm copper strip in 40mm dia G.I pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required. |
| 102 | Providing and fixing 25mm x 5mm strip on surface or in recess for loop earthing as required. |
| 103 | Supplying of LED MIRROR LIGHT 5W 450 LUMEN (PHILIPS ASTRE LINE). (Make: Bajaj/Havells/Crompton) or equivalent to ISI Standard. |
| 104 | Supplying of Exhaust fan (Metallic or PVC Type) of 300mmsweep(Make:Havells/Orient/Bajaj/Crompton) or equivalent to ISI Standard. |
| 105 | Installation of Exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. |
| 106 | Upto 450 mm sweep |
| 107 | Supplying, Installation, testing and commissioning of indoor type floor mounted cubical panel board made of not less than 1.0 mtr X 0.70 mtr X 0.50 mtr. non extendable type L.T - 3 phase 440V , 100A with both side open i/c front double hang shutter with locking arrangement made of 2 mm thick CRCA sheet in different compartment to accommodate various sizes of switch gear, busbar i/c supplying and fixing of following items i/c inter connection with 10 sq. mm copper cable. The panel should have inner earthing, one coat of primer and 2 coat of finishing water proof paint & danger plate etc.as required and its four legs made of equal angle 40 mm x 40 mm x 4 mm and embeded in the groung at the depth of 50 .00 cm with in cement concrete 1: 3 : 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) etc. as required. |
| 108 | MCCB 100 A/TPN (Four Pole) -25 KA breaking capacity with an adustable thermal settings --- 01 No. |
| 109 | Analog Ammeter (0 to 100 A) - 01 No. |
| 110 | Analog Voltmeter (0 to 500 V) - 01 No. |
| 111 | C.T. Coil, Class \\"B\\", with ratio of 100/5A - 03 Nos. |
| 112 | Three Phase Selector switch (for Voltmeter and Ammeter) -- 02 Nos. |
| 113 | Indicating lamp with backup fuse (RYB) - 01 Set. |
| 114 | MCCB- 200 A/TPN (Four pole) 16 KA,breaking capacity - 01 Nos. |
| 115 | MCCB- 63 A/TPN (Four pole) 10 KA,breaking capacity - 02 Nos. |
| 116 | MCCB - 40 A/ TPN (Four Pole)- 10 KA, breaking capacity - 01 Nos. |
| 117 | Copper bus bar strip of size 40 X 5 X 600 mm length for RYBN - 01 Set |
| 118 | Rewirable procelain fuse unit with neutral link 100A (RYBN) - 01 Set |
| 119 | Inter connection with 10 Sq.mm PVC copper cable etc. as required. |
| 120 | Complete set including installation charges. (Make: Havells/L&T/Legrand) or equivalent to ISI Standard. |
| 121 | Supplying and fixing of AC HEAVY DUTY wall mounting fan (450mm sweep)( MAKE USHA DOMINAIRE WALL FAN ) with high speed swing and build in regulator with all accessories etc as required. ( Make: Bajaj /Usha/ Orient/ Crompton or equivalent to ISI standard). |
| 122 | Supplying of prewired LED tube light 20W LUMEN output 2000lm 6500K Product code PANASONIC PBTM02203 or equivalent to ISI standard. (Havells/Panasonic/Polycab) or Equivalent to ISI Standarad. |
| 123 | Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required. |
| 124 | Supplying and fixing brass batten/ angle holder including connection etc. as required. |
| 125 | Supplying of LED Lamp 9W (MAKE : WIPRO TEJAS 9W ) (Make: Bajaj/ Havells /Usha /Orient/Crompton or equivalent to ISI standard). |
| 126 | Dismantling of ceiling fan and painting the same with one or more coats of spray painting with synthetic emamel pain with approved brand and manufacturere to give an even shade, including cleaning the surface with detergent and replacing the damaged rubber reels, nuts and bolts with washer and safety pins, reinstalling the same as required. |
| 127 | Supplying of A.C. Ceiling fan (1200mm sweep, 5 Star Rating, Energy efficient FAN) USHA ENERGIA 50W suitable for operation on 230 Volts, single Phase, 50Hz, A.C Supply including 300mm long rod and without regulator as required. (Make: Bajaj/ Usha/ Orient/Crompton or equivalent to ISI standard). |
| 128 | Supplying and fixing stepped type electronic fan regulator (Socket type)on the switch box including connections etc. as required.Make : anchor/polycab/havells etc or equvalent to ISI standard. |
| 129 | Supplying and fixing of Call Bell/Buzzer, suitable for Single Phase 230 Volt, Complete as required. |
| 130 | Installation, testing and commissioning of ceiling fan, including down road and wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required. |
| 131 | Supplying and fixing of dry type Electrolytic Capacitor for ceiling fan of range between 2.5 to 4.0 mfd, capacitors tolerance ± 5%, operating temperature -25 to 85 degree celcius, rated frequency 50-60 Hz with voltage classification of 370-440V etc. as required. Make: (Rubycon/KEMET/NICHICON/Panasonic or equivalent to ISI Standard). |
| 132 | Supplyig and fixing of 12 or more module Modular type PVC Electrical switch Boards for domestic and Industrial use with high quality Energy efficient rectangular white or other colour and wall mounted heat resistant of 500 Ohms ,shockproof, premium quality and long term durable PVC Electrical Switch Boards of Dimensions: (220 X 160 X 45)mm etc. as required or equivalent to ISI Standard. Make:( Anchor/Havells/Legrand/Polycab or equivalent to ISI Standard). |
| 133 | Supplying and fixing of new generation energy saving enviroment friendly long life 30 W LED street light made up of pressure dia cast aluminium housing with high power LED as light source and embeded PC cover having top opening seprate driver compertment with IP65 PROTECTION AND ik07 IMPACET RESISTENCE (MAKE : Polycab CAT No.PUBO506109 ) along with its Mountning (GI PIPE 32mm) (Make: Bajaj /Havells /Orient/Crompton or equivalent to ISI standard). |
| 134 | Supplying ,Tesing and commissioning of clamp type hook in 40mm Dia Truss Pipe for installation of high way lights etc as required. |
| 135 | Supplying and fixing of wooden meter board size 400mmx200mmx20mm, Base: 30mmx25mm etc. as required. |
| 136 | Supplying and fixing rewirable porceline with fuse unit of 100 amps on energy meter board. Please Enable Macros to View BoQ information |
