Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Chapter- I CIVIL WORK |
| 2 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, leveling & dressing & finishing the top smooth. |
| 3 | Providing and laying in position ready mixed or site batched design mix cement concrete for plain cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana/Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and work-ability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering and finishing as per direction of the engineer-in-charge; for the following grades of concrete. Note : Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the minimum specified cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.i) All works upto plinth level :a) Concrete of M15 grade with minimum cement content of 240 kg /cum |
| 4 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 5 | Centering and shuttering including strutting, propping etc. and removalof form for all heights :a) Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 6 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth Level.a) Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 7 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :a) Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 8 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.a) Cement mortar 1:3 (1 cement :3 coarse sand) |
| 9 | Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry. |
| 10 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.i) Granite of any colour and shadea) Area of slab upto 0.50 sqm |
| 11 | Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.a) Granite work |
| 12 | Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. |
| 13 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 14 | Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminum snap beading shall be paid in basic item) With float glass panes of 4 mm thickness |
| 15 | Providing and fixing powder coated glazed sliding type three track shutter window made out from anodized aluminum frame and shutter section with 4mm thick figure glass sheet in glzed window shutter and stainless steel wire cloth in gauzed window shutter and all necessary jointing cleats glazing clip, rubber packing and aluminum snap beading including vanitaion blind for window etc. |
| 16 | Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / paneling, C.P. brass /stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :Powder coated aluminum (minimum thickness of powder coating 50 micron) |
| 17 | For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shallbe paid for separately) Powder coated aluminum (minimum thickness of powder coating 50 micron) |
| 18 | Providing and fixing anodized aluminum grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment). |
| 19 | Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. a) Using M.S. angels 40x40x6 mm for diagonal braces |
| 20 | Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick :i) Float glass panesa) 5.5 mm thick glass panes |
| 21 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:a) 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 22 | Extra for Providing and fixing flush doors with decorative veneering instead of non decorative ISI marked flush door shutters conforming to IS: 2202 (Part I)a) On one side only |
| 23 | Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws :i) 35 mm thick shuttersa) With ISI marked stainless steel butt hinges of required sizeKiln seasoned selected class of sheesham wood |
| 24 | Providing and fixing chromium plated brass curtain rod/ SS pipe curtain rod having wall thickness of 1.25mm with two nos. similar items brackets fixed with C.P. brass screws and PVC sleeves etc., wherever necessary complete:25 mm dia |
| 25 | Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etc. complete:a) 100x63x4 mm |
| 26 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :a) 300x16 mm |
| 27 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :a) 200x10 mm |
| 28 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :i) 125 mm |
| 29 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.i) Twin rubber stopper |
| 30 | Providing and fixing aluminium casement stays, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. |
| 31 | Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:i) Profile Ba) Fixing with adjustable lugs with split end tail to each jamb. |
| 32 | Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete.a) Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sides |
| 33 | Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand).a) Light shade pigment using white cement |
| 34 | Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :a) 25 mm thick |
| 35 | Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. |
| 36 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete.a) Size of Tile 600x600 mm |
| 37 | Providing and fixing on wall face unplasticised - Rigid PVC rain water pipes conforming to IS : 13592 Type A including unplasticised - PVC moulded fittings/accessoriesto IS : 13592 Type jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. (i) Single socketed pipes. Inclusive of all fittings.a) 110 mm diameter |
| 38 | 20 mm cement plaster of mix :a) 1:4 (1 cement: 4 fine sand) |
| 39 | 20 mm cement plaster of mix :a) 1:4 (1 cement: 4 coarse sand) |
| 40 | 6mm cement plaster of mix: a) 1:3 (1 cement : 3 fine sand) |
| 41 | Rough cast plaster upto 10 m height above ground level with a mixture of sand and gravel or crushed stone from 6 mm to 10 mm nominal size, dashed over and including the fresh plaster in two layers, under layer 12 mm cement plaster 1:4 (1 cement : 4 coarse sand) and top layer 10 mm cement plaster 1:3 (1 cement : 3 fine sand) mixed with 10% finely grounded hydrated lime by volume of cement.a) Ordinary cement finish using ordinary cement |
| 42 | Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers. |
| 43 | Finishing walls with textured exterior paint of required shade :a) New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm |
| 44 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :a) Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture |
| 45 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 46 | Distempering with 1st quality acrylic distember (Ready mix) having VOC content less than 50 grams/ litre of approved brand and manufacture including applying additional coats wherever required to achieve even shade and colour :a) Old work (one or more coats) |
| 47 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shadea) Old work (Two or more coats applied @ 1.43 ltr/ 10 sqm) over existing cement paint surface |
| 48 | Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge.a) With cement mortar 1:4 (1cement: 4 coarse sand) |
| 49 | Making the opening in brick masonry including dismantling in floor or walls by cutting masonry and making good the damages to walls, flooring and jambs complete, to match existing surface i/c disposal of mulba/ rubbish to the nearest municipal dumping ground, all complete as per direction of Engineer-in-Charge.a) For door/ window/ clerestory window |
| 50 | Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after .The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineer in-charge .The elevational area of the scaffolding shall be measured for payment purpose .The payment will be made once irrespective of duration of scaffolding. |
| 51 | Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer 3 mm thick water proofing membrane, black finished reinforced with non-woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrane manufacture of density at 25°C, 0.87-0.89 kg/litre and viscocity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torch and sealing all joints etc, and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 650/ 450N/5cm. Tear strength in longitudinal and transverse direction as 300/ 250N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane :a) 3 mm thick |
| 52 | Extra for covering top of membrane with Geotextile, 120 gsm non woven, 100% polyester of thickness 1 to 1.25 mm bonded to the membrane with intermittent touch by heating the membrane by Butane Torch as per manufactures recommendation |
| 53 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per irection of Engineer - in - charge. |
| 54 | a) Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 55 | b) Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix) |
| 56 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. |
| 57 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.a) In cement mortar |
| 58 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :a) Of area beyond 3 sq. metres |
| 59 | Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead :a) Of area beyond 3 sq. metres |
| 60 | Taking out existing roof sheet covering in terracing including stacking of serviceable material and disposal of unserviceable material within 50 metres lead. |
| 61 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.a) For thickness of tiles 25 mm to 40 mm |
| 62 | Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead |
| 63 | Dismantling C.I. or asbestos rain water pipe with fittings and clamps including stacking the material within 50 metres lead : |
| 64 | a) 75 to 80 mm dia pipe |
| 65 | b) 100 mm dia pipe |
| 66 | Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means including stacking of pipes within 50 metres lead as per direction of Engineer-in-charge :a) 15 mm to 40 mm nominal bore |
| 67 | Dismantling C.I. pipes including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means breaking lead caulked joints, melting of lead and making into blocks including stacking of pipes & lead at site within 50 metre lead as per direction of Engineer-in charge:a) Up to 150 mm diameter |
| 68 | Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead. |
| 69 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. |
| 70 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials bymechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. |
| 71 | Providing and laying 60mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge. |
| 72 | Taking out existing CC interlocking paver blocks from footpath/ central verge, including removal of rubbish etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material within 50 metre lead as per direction of Engineer-in -Charge. |
| 73 | Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :a) W.C. pan with ISI marked white solid plastic seat and lid |
| 74 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:a) White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps |
| 75 | Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:-(a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer |
| 76 | Providing and fixing white vitreous china pedestal type (European type/ wash down type) water closet pan. |
| 77 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. |
| 78 | Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. |
| 79 | Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge.a) 15 mm nominal dia |
| 80 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings completei) Semi rigid pipea) 40 mm dia |
| 81 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 82 | Providing and fixing toilet paper holder:(Jaquar model no. CAN-115n/approved equivalent).a) C.P. brass |
| 83 | Providing and fixing soil, waste and vent pipes. |
| 84 | i) 100mm dia a) Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989 |
| 85 | ii) Centrifugally cast (spun) iron socketed pipe as per IS: 3989a) 75mm dia |
| 86 | Providing & filling the joints with spun yarn,cement slurry & cement mortar 1:2(1 cement: 2 fine sand) in SCI/CI pipes. |
| 87 | a) 75 mm dia pipe. |
| 88 | b) 100 mm dia pipe. |
| 89 | Providing and fixing MS holder bat clamps of approved design to cast iron (spun) pipe embedded in and Including cement concrete blocks 10 x10 x10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc. |
| 90 | a) For 100mm dia. Pipe |
| 91 | b) For 75mm dia. Pipe |
| 92 | Providing and fixing bend of required degree with access door, insertion rubber washer 3mm thick, bolts and nuts complete. |
| 93 | i) 100 mm diaa) Sand cast (spun) iron pipe S&S as per IS 3989. |
| 94 | ii) 75mm diaa) Sand cast (spun) iron pipe S&S as per IS 3989. |
| 95 | Providing and fixing bend of required degree . |
| 96 | i) 100mma) Sand cast (spun) iron pipe S&S as per IS 3989. |
| 97 | ii) Sand cast (spun) iron pipe S&S as per IS 3989. a) 75mm dia |
| 98 | Providing and fixing heel rest sanitary bend |
| 99 | a) Sand cast iron S&S as per IS - 3989 100 mm dia |
| 100 | b) Sand cast iron S&S as per IS - 3989 75 mm dia |
| 101 | Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors |
| 102 | i) 100 mm inlet and 100 mm outleta) Sand Cast Iron S&S as per IS- 3989 |
| 103 | ii) 100 mm inlet and 75 mm outleta) Sand Cast Iron S&S as per IS- 3989 |
| 104 | Providing and fixing vitreous china dual purpose closet suitable for use as squatting pan or European type water closet (Anglo Indian W.C pan) with seat & lid fixed with C.P. brass hinges and rubber buffers, 10 litre low level flushing cistern with fitting and brackets, 40 mm flush bend, 20 mm over flow pipe, with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required:a) White vitreous china dual purpose WC pan with white solid plastic seat and lid with white vitreous china flushing cistern and C.P. flush bend. |
| 105 | Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour.a) Waste coupling 38 mm dia of 83 mm length and 77mm breadth, weighing not less than 60 gms |
| 106 | Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms. |
| 107 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.a) 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. |
| 108 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.a) 25 mm nominal dia Pipes |
| 109 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.i) External work |
| 110 | a) 20 mm nominal dia Pipes |
| 111 | b) 80 mm nominal dia Pipes |
| 112 | c) 100 mm nominal dia Pipes |
| 113 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.Internal work - Exposed on wall |
| 114 | a) 15 mm dia nominal bore |
| 115 | b) 20 mm dia nominal bore |
| 116 | c) 25 mm dia nominal bore |
| 117 | Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall : |
| 118 | a) 15 mm dia nominal bore |
| 119 | b) 20 mm dia nominal bore |
| 120 | Providing and fixing G.I. pipes(medium) complete with G.I. fittings including trenching and refilling etc. a) 32 mm dia nominal bore. |
| 121 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete:a) 15 mm nominal bore |
| 122 | Providing and fixing uplasticised PVC connection pipe with brass unions :i) 45 cm lengtha) 15 mm nominal bore |
| 123 | Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :a) 100 mm diameter |
| 124 | Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work :a) 32 mm diameter pipe |
| 125 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) :a) 25 mm nominal bore |
| 126 | Providing and fixing G.I. Union in existing G.I. pipe line, cutting and threading the pipe and making long screws, including excavation, refilling the earth or cutting of wall and making good the same complete wherever required : |
| 127 | a) 15 mm nominal bore |
| 128 | b) 20 mm nominal bore |
| 129 | c) 32 mm nominal bore |
| 130 | Providing and placing on terrace (at all floor levels) Polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank |
| 131 | Providing and fixing C.P.brass bib cock of approved quality conforming to IS : 8931.with threaded end for hose connection.a) 15 mm nominal bore. |
| 132 | Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.a) 15 mm nominal bore. |
| 133 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.a) 15 mm nominal bore |
| 134 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.a) 15 mm nominal bore. |
| 135 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931a) 15mm nominal bore |
| 136 | Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge. |
| 137 | Providing and fixing PTMT grating of approved quality and colour.a) Circular type 125 mm nominal dia with 25 mm waste hole |
| 138 | Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms. |
| 139 | Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour.a) 15 mm nominal bore, weighing not less than 32 gms |
| 140 | Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : |
| 141 | a) 100 mm diameter |
| 142 | b) 150 mm diameter |
| 143 | Providing and fixing square mouth SW gully trap class SP-1 complete with CI grating brick masonry chamber and water tight CI cover with frame of 300 x 300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg. as per standard design.i) 180x150mm size P typea) with common burnt clay F.P.S. (non modular) bricks of class designation 7.5. |
| 144 | Drilling suitable holes in reinforced or plain cement concrete with power driven drill machine to a minimum depth of 100mm upto 200mm in RCC beams, lintels, columns and slabs to introduce steel bars for sunshades/balconies including fixing the steel bars in position using epoxy resin anchor grout of approved make but excluding the cost of reinforcement, all complete as per direction of Engineer-In-Charge.a) Upto and including 12mm dia. |
| 145 | Providing and fixing hard drawn steel wire fabric of size 75 x25 mm mesh or other suitable size wire mesh to be fixed & firmly anchored to the concrete surface by means of \\"L\\" shaped mild steel shear key welded with existing reinforcement including the cost of materials, labour, tool & plants as approved by Engineer-in-charge. |
| 146 | Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2 mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady] the frame. |
| 147 | Providing and fixing to existing door frames. a) 30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames. |
| 148 | Providing reinforced by organic fibres and/or inorganic synthetic fibres cement 6 mm thick corrugated sheets (as per IS: 14871) roofing up to any pitch and fixing with polymer coated J, or L hooks, bolts and nuts 8 mm dia. G.I. plain and bitumen washers or with self drilling fastener and EPDM washers etc. complete (excluding the cost of purlins, rafters and trusses), including cutting sheets to size and shape wherever required. |
| 149 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 150 | CHAPTER - II ELECTRICAl WORKSUB HEAD - 08 (Wiring) |
| 151 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with piano type switch, phenolic laminated sheet, suitable size M.S. box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required.a) Group B |
| 152 | Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface /recessed medium class PVC conduit, 2 way piano type switch, phenolic laminated sheet, suitable size MS box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductorsingle core cable etc. as required |
| 153 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required |
| 154 | a) 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire |
| 155 | b) 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire |
| 156 | c) 2 X 4 sq. mm + 1 X 4 sq. mm earth wire |
| 157 | d) 2 X 6 sq. mm + 1 X 6 sq. mm earth wire |
| 158 | e) 4 X 10 sq. mm + 2 X 6 sq. mm earth wire |
| 159 | f) 4 X 16 sq. mm + 2 X 6 sq. mm earth wire |
| 160 | Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.a) 2 Pair |
| 161 | Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required. |
| 162 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. |
| 163 | a) 20 mm |
| 164 | b) 25 mm |
| 165 | Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required.i) 75 mm X 75 mm X 60 mm deep |
| 166 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. |
| 167 | a) 5/6 A switch |
| 168 | b) 15/16 A switch |
| 169 | c) 3 pin 5/6 A socket outlet |
| 170 | d) 6 pin 15/16 A socket outlet |
| 171 | d) Telephone socket outlet |
| 172 | e) TV antenna socket outlet |
| 173 | f) Bell push |
| 174 | Supplying and fixing stepped type electronic fan regulator on the existing switch board including connections but excluding modular plate etc. as required. |
| 175 | Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. |
| 176 | a) 4 Module (125mmX75mm) |
| 177 | b) 6 Module (200mmX75mm) |
| 178 | c) 8 Module (125mmX125mm) |
| 179 | d) 12 Module (200mmX150mm) |
| 180 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required. |
| 181 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. |
| 182 | Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required. |
| 183 | Supplying and fixing brass batten/ angle holder including connection etc. as required. |
| 184 | Supplying and fixing call bell/Buzzer suitable for single phase 230 volts,complete as required |
| 185 | Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required. |
| 186 | Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes. |
| 187 | FANS & LIGHT FIXTURESSupply, Installation,Testing and comissioning of following light fixtures, with lamp, control Gear & All necessary accessories. Luminaries with all electrical accessories & it should be energy effiecient, etc are prewired up to on wall/ Ceiling including all fixing accessories, etc complete as required. The led shall be complete with Low loss copper driver all prewired upto the terminal block. All fixtures shall be supplied with lamps. |
| 188 | a) 13W (4Feet) LED Light Fixture- Make-Phillips CAT NO. 1200mm, 13W865 T8 I IN30- 1600lm or equivalent. |
| 189 | b) 36W LED recess mounted fixture Make Phillips CAT NO. : RC420B M LED 30S-6500PSU WH or equivalent. |
| 190 | c) 20W LED recess mounted fixture Make Phillips CAT NO. : SM251C LED20S-6500PSU WH or equivalent. |
| 191 | d) 22W MIRROR LIGHT Surface Mounted Make Phillips CAT NO. : BN021C LED22S PSU CW GR or equivalent. |
| 192 | Installation of exhaust fan in the existing opening, including marking good the damage connectin, testing, commissioning etc. as requireda) Upto 450 mm sweep |
| 193 | Supply 900 RPM Exhaust 305 mm fan / wall mounted fan suitable for suitable for single phase 230/240V, AC Supply complete with motor MS louvers , mounting brackets, all accessories etc as complete. |
| 194 | Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) |
| 195 | a) 8 way, Double door |
| 196 | b) 12 way, Double door |
| 197 | Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB /Isolator)i) 8 way (4 + 24), Double door |
| 198 | Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, “C”curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections,testing and commissioning etc. as required. |
| 199 | a) Single pole |
| 200 | b) Double pole |
| 201 | Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.a) 40 A |
| 202 | Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.a) 40A / 63A |
| 203 | Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, \\"C\\" curve including connections, painting etc. as required. |
| 204 | (Earthing)Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.a) Upto 35 sq. mm (clamped with 1mm thick saddle) |
| 205 | Schedule of Credit |
| 206 | Bricks |
| 207 | Bricks Bat |
| 208 | For Steel / MS Steel |
| 209 | Old Point Wiring |
| 210 | Old Wiring for twin control light point |
| 211 | Old Submain wiring of following typea) 2 x 1.5 sq. mm + 1 x 1.5 sq. mm earth wire |
| 212 | b) 2 x 2.5 sq. mm + 1 x 2.5 sq. mm earth wire |
| 213 | c) 2 x 4 sq. mm + 1 x 4 sq. mm earth wire |
| 214 | d) 2 x 6 sq. mm + 1 x 6 sq. mm earth wire |
| 215 | e) 4 x 10 sq. mm + 2 x 6 sq. mm earth wire |
| 216 | f) 4 x 16 sq. mm + 2 x 6 sq. mm earth wire |
| 217 | Old Telephone cable 2 pair |
| 218 | Old co-axial TV Cable |
| 219 | Old PVC conduit of any size with accessories |
| 220 | Old Metal Box with laminated shee cover |
| 221 | Old Switch , socket etc. |
| 222 | Old Electronic fan regulator |
| 223 | Old G.I. Box of any size with cover plate |
| 224 | Old G.I. Box of any size with cover plate & switch & Socket of any rating |
| 225 | Old Ceiling Rose |
| 226 | Old Brass Holder |
| 227 | Old Call Bell |
| 228 | Old LED Light Fixture of any type |
| 229 | Old Exhaust Fan 305 mm size |
| 230 | Old SPN Distribution Board of any Size |
| 231 | Old TPN Distribution Board of any Size |
| 232 | Old MCB / Isolator of any type |
| 233 | Old G.I. Box with Socket & MCB |
| 234 | Old Cable of size 35 sqm Quoted Percentage (+) / (-) and Total Amount in Figures(inclusive of CP / OH and levied Taxes) Please Enable Macros to View BoQ information |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
| 5 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
