|
| 1 | Earthwork in cutting to form road section in correct profile including removal of spoils not exceeding initial lead of 50m and initial lift of 1.5m (Mode of measurement: pre works and post works) (ii) In mixed soil (i,e. clay mixed with kankar, pebbles, moorum etc.) |
| 2 | Earth work in excavation of foundation trenches or drains in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing,spreading or stacking the spoils within a lead of 75m.as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete. Depth of excavation not exceeding 1500 mm |
| 3 | Labour for laying 150 mm to 200 mm boulder soling including rough dressing hand packing and ramming down small pieces in the interstics including rolling and preparing the bed to proper level and filling up all joints with sandy clay or earth. |
| 4 | Earthwork in filling in foundation trenches or plinth with good earth, in layers not exceeding 150mm. including watering and ramming etc. layer by layer complete. (Payment to be made on the basis of measurement of finished quantity of work)(a) With earth obtained from excavation of foundation. |
| 5 | (II) Cement concrete with 30 mm down graded shingles excluding shuttering. N.B. VarietyIn ground floor(a) 1:3:6 proportion |
| 6 | Rubble masonry in cemen t(1:6) with hard dressed stones from approved quarries and clean, coarse and washed sand including carriage of all materials to site. (b) In Fine dressed work in Building(i) In Ground Floor |
| 7 | Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns,lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor)a) 25 mm to 30 mm thick wooden shuttering as per decision & direction of Engineer-in-Charge |
| 8 | Plum concrete work with 40% cement concrete with 30 mm down graded stone metal and 60% stone boulder of size 150mm and above,placed in position as directed excluding shuttering if any. |
| 9 | Providing weep holes in Brick masonry / Plain /Reinforced concrete abutment, wing wall / return wall with 100 mm dia AC pipe, extending through the full width of the structure with slope of 1V:20H towards drawing face. Complete as per drawing and Technical specifications. |
| 10 | Ordinary Cement concrete ( mix 1:1.5:3) with graded stone chips ( 20 mm nominal size) excluding shuttering and reinforcement if any in ground floor as per relevant IS codes.24.423 (ii ) River Bazree |
| 11 | Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction.(a) For works in foundation and upto roof of ground floor/upto 4 m(i) Tor steel/Mild Steel SAIL/TATA/RINL |
| 12 | 125mm. thickbrickworkwith1st class bricks incementmortar (1:4) inground floor. |
| 13 | Supplying, fitting&fixing1st qualityCeramic tiles inwalls and floors tomatchwith theexistingwork&4nos. of key stones (10mm) fixedwitharalditeat thebackof each tile& finishing the jointswithwhite cementmixedwithcolouring oxide if required to match the colour of tiles including rougheningof concrete surface, if necessaryorby synthetic adhesive & grout materials etc. (A) Floor WithSandCementMortar (1:4) 20mmthick&2mmthick cement slurry at back side of tiles using [email protected] Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m. (b) Area of each tile above 0.09 Sq.m (i) Coloured decorative |
| 14 | Supplying,Fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc. (B) Wall With Sand Cement Mortar(1:3)15mmthick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m. & joint filling using white cement slurry @0.20kg/Sq.m.(B) WallWith Sand Cement Mortar (1:3) 15 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m.(a) Area of each tile upto 0.09 Sq.m(i) Coloured decorative |
| 15 | (a) M.S.or W.I. Ornamental grill of approved design joints continuously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessary screw sand lugs in ground floor.(Add extra @1% for each addl. floor upto 4th floor and @1.25% for each addl. floor above 4th floor)i) Grill weighing above 10Kg/sqmtr and upto 16 Kg./sq.mtr |
| 16 | Supplying and laying true to line and level vitrified tiles of approved brand (size not less than 600mmx600mmx10mm thk) in floor, skirting etc. set in 20mm sand cement mortar(1:4) and 2mm thk cement slurry back side of tiles using cement @ 2.91kg/m2 or using polymerised adhesive(6mm thk layer applied directly over finished artificial stone floor/mosiac etc without any backing course) laid after application slurry using 1.75kg of cement per m2 below mortar only, joints grouted with admixture of white cemet and colouring pigment to match with colour of tiles/epoxy groutmaterials of approved make as directed and removal of wax coating of top surface of tiles with warm water and polishing the tiles using soft and dry cloth upto mirror finish complete true to materials, labour and all other incidential charges complete true to manufacturer's specification and direction of Engineer-In-Charge.(White cement, synthetic adhesive and grout materials to be supplied by the contractor) With application slurry @1.75kg/m2, 20mm sand cement morter(1:4) & 2mm thick slurry at back side of tiles, 0.2kg/m2 white cement for joint filling with pigment. Deep Colour & White |
| 17 | Plaster(towall, floor, ceilingetc.)withsandandcementmortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface] (ii) With 1:4 cement mortar (b) 15 mm thick plaster |
| 18 | Plaster(towall, floor, ceilingetc.)withsandandcementmortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface] (ii) With 1:4 cement mortar (a) 20 mm thick plaster |
| 19 | Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame exluding cost of concrete, Iron Butt Hinges and M.S clamps. (The quantum should be correted upto three decimals). Local wood |
| 20 | Panel shutters of door and window, as per design (each panel consisting of single plank without joint), including fitting and fixing the same in position but excluding the cost of hinge and other fittings.In ground floor.(In case of non-supply of single plank, penal rate of reduction of 20% will be made)(iii) 35mm thick shutters with 19mm thick panel of size 30 to 45 cm.(b) Sishu, Gamar, Champ,Badam,Bhola, Mogra, Hallak. |
| 21 | Supplying, fitting and fixing windows and ventilators with or without integrated grills conforming to IS1038-1975 and manufactured from rolled steel sections conforming to IS7452-1974 with non-friction projecting type, boxtype hinges, glazing clips, lugs locking bracket, handle plate etc, including hoisting in position, straightening if required, fixing lugs in cement concrete(1:2:4) with stone chips 20 mm down cutting holes andmending good damages to match with existing surface complete in all respect excluding glazing. (b)Openablesteelwindowsasper ISsizeswithsidehungshuttersand horizotal glazing bars. [The extra rate admissible for theopenable portion only] |
| 22 | Supplying best Indian sheet glass panes set in putty and fitted and fixed with nail sand putty complete. (In all floors for internal wall & upto 6 m height for external wall)ii) 4 mm thick |
| 23 | M.S. structural works in roof trusses with tubular sections conforming to IS: 806-1968&IS: 1161-1998 ................................... all incidental chages such as electricity charges, labour insurance charges etc. i) For trusses spanning up to 12.00 m |
| 24 | Supplying, fitting & fixing Zn-Al alloy (55% Al & 45% Zn)coating of 150 grams per sq. metre (followed by colour coated on both side) steel sheet work having minimum yield strength of 550 Mpa of trapizoidal profile of approved make (excluding the supporting frame work) fitted and fixed with 55 mm & 25 mm self tapping screw, EPDM Washer 16 mm dia & 3 mm th. washer etc. complete with 150 mm end lap and one corrugation minimum side lap. (Payment to be made on area of finished work). |
| 25 | Providing and fixing of false ceiling with powder coated exposedG.I. grid suspension system(E-GridU-1520 or equivalent load carrying capacity with mid span deflection not exceeding 1/360 span with hanger spacing of 1200mm c/c) consisting of Main Runner 3600mm long,Cross Tee 1200mm/600mm long and Wall Angle. TheWall Angle shall be fixed onPVCDashFasteners on the perimeter of the wall by steel screws with distance 300mmc/c.The Main Runners to be placed @1200mm. The Cross Tee 1200mm will be inserted in the pre-cut slots of Main Runner at aregular interval of 600mm to form a modular grid of 1200mm X 600mm. Additional Cross Tees of 600 mm shall be placed perpendicular to the Cross Tee1200mm long to finally form a grid of 600mmX 600mm.Grid of module size 600mm X 600mm shall be supported by 6mm dia G.I.wire from purlins / soffit. 15mm thick OW Acoustic Board (MineralFiber Acoustic Ceiling Tiles) of approved patern and size595mmX595mm with NRC value>0.65 should be placed in the Grid module to form a False Ceiling.All complete as per the drawing & directions of Engineer-in-charge. In ground floor.a) Acoustic False Ceiling (with 15mm thick OW Acoustic Board and E-Grid U 1520). |
| 26 | Supplying, fitting and fixing M.S. clamps for door and window frame made of flat bent bar, end bifurcated with necessary screws etc. by cement concrete(1:2:4) as per direction. (Cost of concrete will be paid separately)(b) 40mm X 6mm, 200mm Length |
| 27 | Anodised aluminium butt hinges of approved quality manufactured from extruded section conforming to I.S. specification (I.S.205/66) and fitted and fixed with cadmium plated screws:(v) 100 x 63 x 3.2mm |
| 28 | Anodised aluminium barrel / tower / socket bolt (full covered) of approved manufactured from extruded section conforming to I.S. 204/74 fitted and fixed with cadmium plated screws:(iii) 100mm long x 10mm dia. Bolt |
| 29 | Anodised aluminium Aldrop / Sliding bolts of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 2681/66) fitted and fixed complete.(i) 250mm x 16mm dia bolt. |
| 30 | Anodised aliminiumD-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 230/72) fitted and fixed complete:(a) With continuous plate base (Hexagonal/ Round rod)(ii) 100 mm grip x 10 mm dia rod. |
| 31 | Neat cement punningabout 1.5mmthick inwall, dado,window sill, floor etc.NOTE:Cement 0.152 cu.m per100 sq.m. |
| 32 | (a)Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces b ysand papering etc. |
| 33 | (A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary :(b) On steel or other metal surface :With super gloss (hi-gloss) (iv) Two coats (with any shade except white) |
| 34 | (b) Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. |
| 35 | (A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary :(a) On timber or plastered surface :With super gloss (hi-gloss) (iv) Two coats (with any shade except white) |
| 36 | Wooden eaves board as per design, fitted and fixed complete:In ground floor (i) Plain eaves board (Local Sal)(a) 19mm thick |
| 37 | Galvanised iron sheet ridging fitted with necessary bolts, screws, washers etc complete.(225mm end lapping)(A) 300 mm lapping each way(a) With 0.60 mm sheet |
| 38 | Galvanised iron sheet eaves gutter fitted and fixed with necessary 50mm X 6mm M.S flat bar clamps bent todesign, bolts, nuts, washers etc. complete.Eaves gutter made of 0.63 mm. sheets.(300mm End lapping) (a) 225 mm. wide gutter |
| 39 | Supplying, fitting & fixing UPVC pipes A- Type and fittings conforming to IS:13592-1992 with all necessary clamps nails, including making holes in walls, floor etc. and cutting trenches in any soil through masoury concrete structures etc. if necessary and mending good damages including jointing with jointing materials (Spun yarn, valamoid / bitumen/M.seal etc) complete. A) UPVC PIPES ii) 110mm Dia |
| 40 | Supplying, fitting & fixing UPVC pipes A- Type and fittings conforming to IS:13592-1992 with all necessary clamps nails, including making holes in walls, floor etc. and cutting trenches in any soil through masoury concrete structures etc. if necessary and mending good damages including jointing with jointing materials (Spun yarn, valamoid / bitumen/M.seal etc) complete.B) UPVC Fittings:c) Bend 87.5 degree (ii) 110 mm. Dia. |
| 41 | Supplying, fitting & fixing UPVC pipes A- Type and fittings conforming to IS:13592-1992 with all necessary clamps nails, including making holes in walls, floor etc. and cutting trenches in any soil through masoury concrete structures etc. if necessary and mending good damages including jointing with jointing materials (Spun yarn, valamoid / bitumen/M.seal etc) complete.B) UPVC Fittings:d) Shoe (ii) 110 mm. Dia. |
| 42 | Rendering theSurfaceofwalls andceilingwithWhiteCement base WATER PROOF wall putty of approved make & brand.(1.5 mm thick) |
| 43 | Acrylic Distemper to interior wall, ceiling with acoatofsolventbased interior grade acrylic primer (as per manufacturer's specification) including cleaning and smoothning of surface.Two Coats |
| 44 | Applying decorative cement based paint of approved quality after preparing the surface including scraping the same thoroughly (plastered or concrete surface) as per manufacturer's specification (iii) Two coats. |
| 45 | Construction of Septic tank of different capacities as per approved drawing with 1st class brick work in cement mortar (4:1) including two 560 mm dia. R.C.C. manhloe cover of approved make supplied, fitted and fixied in the top slab with necessary fittings, 19 mm thick cement plaster(4:1) with neat cement finish to the internal surfaces and 12 mm thick plaster(4:1) to outside wall upto 200 mm below G.L. floor finished with 25 mm thick grey artificial stone including supplying, fitting and fixing all necessary specials, fittings, S.W. tees, C.I. foot rest etc. including excavating earth in all sorts of soil, shoring, bailing and pumping out water as necessary, ramming, dressing the bed and refilling the sides of the tank with earth, removing spoils, fliing up the chamber with clear water, removing foreign materialsfrom the chamber and including constructing attached inspection pit as per approved dawing and connecting all necessary pipes, joints etc. with internal plaster work and artificial stone flooring is to be done with admixture of water proofing compound @ 5% by weight of cement, complete in all respect as per directon of Engineer-in-For 50 users.with Bazree (N.B.Variety).(SAIL/TATA/RINL)Charge. |
| 46 | Constructing Inspection pit of inside measurement 600mm X 600mm X upto 600mm (depth) with 250 mm thick 1st. class brick work in cement mortar (1:4) on all sides, bottom of the pit consisting of 100 mm thick cement concrete (1:3:6) with stone chips over a layer of jhama brick flat soling, 15 mm thick (1:4) cement plaster to inside walls and out-side walls upto G.L. and 20 mm.thick (1:4) plaster to bottom of the pit, providing necessary invert with cement concrete (1:3:6) with stone chips as per direction, neat cement finishing to entire internal surfaces, top of the pit covered with 100 mm thick R.C.C. slab (1:1.5:3) with stone chips and necessary reinforcements upto 1% and shuttering including 6 mm thick cement plaster (1:4) in all external surfaces of the slab and one 560 mm dia. R.C.C. manhole cover of approved make supplied, fitted and fixed in the slab with necessary fittings, necessary earthwork in excavation in all sorts of soil, filling sides of the pit with earth and removing spoils after work complete in all respect with all costs of labour and materials.ii) With Bazree (N.B Variety) (SAIL/TATA/RINL) |
| 47 | Supplying, fitting and fixing G.I. pipes of TATA make with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads, fitting, fixing etc.complete in all respect including cost of necessary fitting as required, jointing materials and two coats of painting with approved paint in any position above ground.( Payment will be made on the center line measurements of total pipe line including all specials. No seperate payment will be made for accesorie, specials.).For exposed work.15 mm dia.light quality. |
| 48 | Supplying, fitting and fixing G.I. pipes of TATA make with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads, fitting, fixing etc.complete in all respect including cost of necessary fitting as required, jointing materials and two coats of painting with approved paint in any position above ground.( Payment will be made on the center line measurements of total pipe line including all specials. No seperate payment will be made for accesorie, specials.). 15 mm dia.medium quality. |
| 49 | Supplying, fitting and fixing G.I. pipes of TATA make with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads, fitting, fixing etc.complete in all respect including cost of necessary fitting as required, jointing materials and two coats of painting with approved paint in any position above ground.( Payment will be made on the center line measurements of total pipe line including all specials. No seperate payment will be made for accesorie, specials.). 15 mm dia.medium quality. |
| 50 | Supplying, fitting and fixing Orissa pattern water closet in white glazed vitreous chinaware of approved make in position complete excluding 'P' or 'S' trap (excluding cost of concrete for fixing).580 mm X 440 mm. |
| 51 | Supplying, fitting and fixing 10 litre porcelian low-down cistern of approved make without fitting and brackets.White. |
| 52 | Wash basin white vitreous china of approved make (without fittings) supplied, fitted and fixed in position on 75mm X 75mm X 75mm wood blocks and C.I. Brackets including two coats of painting of C.I. Brackets. 630 mm x 450 mm size. |
| 53 | Supplying, fitting and fixing PVC pipes for underground work ofapproved make of Schedule 80 (medium duty) conforming to ASTMD -1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). withall necessary accessories, specials viz. socket, bend, tee, union, cross,elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc.fitted including ostofallmaterials ,jointing materials, cutting pipes,making threads ,cutting trenches upto 1.5 metre below surface in all sortsof soil and refilling the same as directed complete in all respect. (Paymentwill be made on the centre line measurement of the total pipe lineincluding all specials No separate payment will be made for accessories,specials.)150 mm |
| 54 | Supplying, fitting and fixing bib cock or stop cock (a) (i) Chromium plated Bib Cock short body (Equivalent to Code No. 511 & Model - Tropical / Sumthing Special of ESSCO or similar brand).15 mm |
| 55 | Supplying, fitting and fixing bib cock or stop cock (a) (i) Chromium plated Bib Cock long body with flange |
| 56 | Supplying,fitting and fixing approved brand P.V.C. CONNECTOR whiteflexible, with both ends coupling with heavy brass C.P. nut, 15 mm dia. |
| 57 | Supplying, fitting and fixing bevelled edged mirror 5.5 mm thick silver redas per I.S. 3438 / 1965 together with brass C.P. hinges. |
| 58 | Supplying, fitting and fixing porcelain toilet paper holder of approved makewith wooden spindle as necessary. |
| 59 | Supplying, fitting and fixing liquid soap container. |
| 60 | Supplying PVC water storage tank of approved quality with closed top weith lid (Black) - Multilayer.1000 litre capacity. |
| 61 | Supplying, fitting and fixing bib cock or stop cock.Chromium plated Bib Cock short body (Equivelent to Code No.511 & Model- Tropical /sumthing special of ESSCO or Similar brand). Please Enable Macros to View BoQ information |
