|
| 1 | Excavation in trenches in any type of soil n.exc 1.50m wide and n. exc 1.50m in depth and getting out complete all as specified. |
| 2 | Surface dressing n. exc.30cm deep and averaging 15cm deep and getting out in any type of soil. |
| 3 | Removal of excavated (soil) to a distance not exceeding 50m and depositing where directed at a level not exc. 1.5m above the starting point. |
| 4 | Returning, filling in, including spereading, leveling, watering and well ramming in layers not exc 25cm. |
| 5 | M&L Cement Concrete in foundation filling and mass concrete of mix 1:4:8 type D2 (40mm graded aggregate). |
| 6 | M&L Brick work with sub class 'B' bricks straight of curved on plan exc 6m mean radius built in CM 1:6 including flush pointing with same mortar as the work proceed complete as specified. |
| 7 | M&L brickwork with subclass 'B' bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 |
| 8 | M&L Rendering 15 mm thick on other than fair faces of brick work or concrete surfaces with 1:6 CM on internal faces of wall, finishing the surfaces even & smooth w/o using extra cement. |
| 9 | M&L Rendering 15mm thick on brick or concrete surface in CM 1:4, finished even and smooth with out using extra cement |
| 10 | M&L Rendering 10mm thick on fair faces of concrete surfaces with 1:3 CM on ceiling surfaces etc., finishing the surfaces even & smooth w/o using extra cement. |
| 11 | M&L Reinforced cement concrete M-25 (Design mx) using 20mm graded crushed stone aggregates as in foundations, including rafts, footings, foundation beams, plinth beams, bsaes of columns etc basement slabs, under-reamed piles and mass concrete |
| 12 | M&L Reinforced cement concrete M-25 (Design mx) using 20mm graded crushed stone aggregates as in slabs, supported on walls, beam and columns in floors, and in shelves and the like. |
| 13 | M&L Reinforced cement concrete M-25 (Design mx) using 20mm graded crushed stone aggregates as in columns, pillars ,piers,posts and struts |
| 14 | M&L Reinforced cement concrete M-25 (Design mx) using 20mm graded crushed stone aggregates as in beams ,chhaja,cantilevers, bressummers, lintels over 1.5 mtr span |
| 15 | Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams,sides and sofits of foundation and plinth beams; and similar works; vertical or to batter for rough finished flat surfaces complete all as specified |
| 16 | Form work to edges of concrete flats, breaks in floors, openings in concrete walls,floors and roofs and sides of RCC/PCC bands in walls, horizontal or sloping and similar work all exceeding 20 cm wide for rough finished flat surfaces of concrete complete all as specified. |
| 17 | Form work to sides of pillars, posts, struts, piers, columns and stanchions for rough finished flat surfaces of concrete complete all as specified |
| 18 | Form work to soffits of suspended slabs such as roof slabs, floor slabs etc not exceeding 200mm thick. |
| 19 | M&L TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified and directed. |
| 20 | -ditto- here-in-before but 8mm dia and over upto and including 10mm dia as in stirrups, spacers, binders. |
| 21 | M&L 75 mm thick Cement concrete 1:4:8 type D-2 (using 40 mm graded agg) as in sub base. |
| 22 | M&L For non – skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface over and including 15 mm thick screed bed in CM 1:6 complete all as specified and as directed by Engineer-in-Charge. |
| 23 | M&L For Glazed Ceramic Coloured tiles in vertical surface 450mmx300mmx7mm thick, set and jointed in neat cement slurry and pointed white or coloured cement to match the surface over and including 10 mm thick CM 1:4 complete all as specified and as directed by Engineer-in-Charge. |
| 24 | S&F factory made 18 mm (+0.7mm) thick HDHMR Board manufacured by an ISO 9001-2008 certified company. Both side prelaminated for kitchen cabinet shutter and also manufactuer's test report and test certificate is mandatory with each and every supply of the material complete as per manufacturer's specifications and drawing and as directed. |
| 25 | M&L for steel fancy handle 200 mm sizefor kitchen cabnet complete all as specified and as per sample kept in GE office. |
| 26 | M&L for corner crank hinges for kitchen cupboard/ almiraha. Any size any type for md offrs accn complete all as specified and as per sample kept in GE office. |
| 27 | M&L for Aluminium Powder Coated, sliding window three track with mosquito proofing with style 44.4x44.5x2mm thick including 4mm thick coloured/tinted/frosted glass panes including provision for exhust fan if required as directed and all necessary fittings and fixtures complete all as specified and directed. |
| 28 | M&L For Anodised Aluminium Grills, 6mm Dia Size 100 x 100mm fixed to aluminium windows and thickness of powder coating not less than 50 micron, complete all as specified. |
| 29 | S&F For Powder Coating aluminium single or double leaf door shutter in single or two panels with standered aluminium section weighing 0.55 kg/m including necessary joining cleat, glazing clilps,rubber neoprene packing , handles 2 Nos in each door hinges,powder coated snap beading screws etc in partition of partly glazed (5mm thick tinted) and partly prelaminated board 12mm thick (bothside) including locking arrangement, using following section of Jindal or equivalent make complete all as specified and directed by Engineer-in-Charge. (Note:- Aluminium section size specified above if not available in the market next immediate higher size of same make shall be provided without any extra cost to the Govt.) |
| 30 | M&L for Spreading and levelling in layers n exc. 25 cm thick and watering and well ramming under floor complete all as specified and directed. |
| 31 | M&L Hardcore of gauge n. exc. 63mm broken stone boulders, deposited spread and levelled in layers n. exc. 15cm thick, watered and rammed to a true surface in broken bricks boulders. |
| 32 | M&L 75 mm thick 1:3:6 type C-2 using 40 mm graded agg in plinth etc.laid in alternate bays finished even and fair w/o using extra cement. |
| 33 | M&L for preparation of new plastered surface and applying two coats of Cement Base Paint on wall. |
| 34 | M&L Preparation of new plastered surfaces and applying 3mm thick wall care putty on plastered surfaces and over applying two coats of distemper oil emulsion all as specified and directed by Engineer-in-Charge. |
| 35 | M&L Prepration of new plastered surfaces on ceiling over applying three coats of white washing. |
| 36 | M&L for roof treatment with the following specification - applying water proofing treatment on horizontal or vertical surfaces by applying oil bound bitumen primer @ 0.20 Kg/sqm and providing 3mm thick APP modified water proofing membrane weighing not less than 3 Kg/sqm reinforced with non-woven polyester matt weighing not less than 160 gm/sqm, The overlap shall be minimum 100mm on transverse direction and 75 mm on longitudinal direction and sealing overlap by torch application and bonded and applying a coat of blown grade hot bitumen 85/25 over and below the membrane @ 1.20 Kg/sqm in drying over the membrane finished with solar reflective bituminous aluminium paint/ primer @ 0.10 Kg/sqm over RCC roof slab/ parapet after cleaning the surfaces by removing dust, dirt etc. as per manufacturer’s instructions including 15mm thick screed in CM 1:4 and all as specified and as directed.NOTE :- The work shall be executed at site by the authorised applicator of APP and as approved by the GE. |
| 37 | S&F Oval Shape Counter Wash Basin white ,size 400 x 400mm are fixing in Granite including brackets and cutting for and pinning in ends of brackets or erecting stand including CP 32mm waste coupling and waste pipe. |
| 38 | S&F Pillar tap cast copper alloy fancy type with capstan heads, chromium plated Fancy type screwed down high pressure with or without lettered ‘Hot’ or ‘Cold’ with long shanks and nut screwed for iron pipe of 15 mm bore |
| 39 | S&F bib taps screwed down high pressure with both ends for iron pipe 15mm bore fancy type chromium plated as complete. |
| 40 | S&F stop valve cast copper alloy ,chromium plated fancy type, screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe. |
| 41 | S&F PVC connection 15mm size with PTMT nuts of length 450mm. |
| 42 | Supply & fixing stainless steel peg set of six hooks fixed on patti of size 50cm to 60cm, complete all as specified and as directed. |
| 43 | S&F For Looking mirror of size 1200mmx750mm,selected quality glass approved size 6mm thick,mounted on walls with SS Screws as directed by Engineer-in charge. |
| 44 | S&F brass chromium plated tubular towel rails 20mm dia D type 60cm long between flanges. |
| 45 | S&F Towel Ring of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms) all as specified and directed. |
| 46 | S&F Fancy type Stainless Steel, soap dish, all as specified and directed. |
| 47 | S&F PVC shelves of PTMT fixed with and including chromium plated brass screws and plastic cleats. |
| 48 | S&F Stainless Steel curtain rods 20mm dia powder coated with brackets, corner & fineals complete all as specified and as directed by Engineer-in-Charge. |
| 49 | Supply & Fixed 20mm bore dia of tubing with screwed socket joints, medium grade galvanized steel with all necessary tube fittings and fixing complete with clips, wall hooks etc to wall and ceilings or laid in floor including necessary changing and cutting in brick/concrete surfaces and making good the disturbed surface complete in all respect as specified. |
| 50 | Supply & Fixed 15mm bore dia of tubing with screwed socket joints, medium grade galvanized steel with all necessary tube fittings and fixing complete with clips, wall hooks etc to wall and ceilings or laid in floor including necessary changing and cutting in brick/concrete surfaces and making good the disturbed surface complete in all respect as specified in CM 1:4. |
| 51 | S&F 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joint in walls. |
| 52 | S&F PVC SWR Bends in any radius 75 mm bore. |
| 53 | S&F for 75mm bore PVC (SWR) floor trap plain with grating including jointing with solvent cement. |
| 54 | S&F water tank with rotational moulded polythene water storage tank (cylindrical vertical with closed top) of 1000 Ltr capacity hoisted and fixed in position with 20mm PTMT ball valve all as specified in SSR Part I. |
| 55 | S&F Gun-metal Globe or gate valves 20 mm nominal bore dia with gate with iron wheel head screwed both ends for iron pipes and fixed all complete as per direction of Engineer-in-charge. |
| 56 | M&L Granite black colour of any type 20mm thick machine cut as in cooking plateforms and like in cement mortar ( 1:4 ) incl pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and 20mm thick screed bed or bedding layer of mortar in cm 1:6 for laying floor finishes. |
| 57 | Rounding/moulding to edges of stone slabs, marble stone, granite stone slabs one edge, such as in steps, cooding platform , and other similar situations etc. |
| 58 | Surface excavation n. exc (not exceeding) 30cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified. |
| 59 | Excavating in trenches, n.exc 1.50m wide and n. exc 1.50m in depth; for foundation, & n exc 10 Sqm on plan and n exc 1.5m in depth and getting out in soft/loose soil, complete all as specified. |
| 60 | M&L PCC 1:2:4 Type B0 (using 12.5mm graded crushed stone aggregate) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs etc all as specified and directed by Engr-in-charge. |
| 61 | M&L for 10 mm thick rendering on fair faces of brick/ concrete surfaces in cement mortar 1:6 and finished even and smooth without using extra cement complete all as specified. |
| 62 | Supply only Liquid water proofing compound complete all as specified. |
| 63 | M&L Shingle filling (Small pieces of stone) in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled, and blinded with earth and rammed including watering complete all as specified. |
| 64 | M&L 75 mm thick cement concrete (1:4:8) type D2 as sub base to floor as specified. |
| 65 | M&L for 100mm thick Cement Concrete type B-1 (20mm graded stone aggregate) as in floor finished even and smooth with using extra cement laid in alternate bays, area of each bays not exc, 9 Sqm. |
| 66 | S&F for glass dividing strips, 3mm thick and 38mm wide inserted in position, confirm to design. |
| 67 | M&L for hardcore of broken stone or boulders of gauge not exc 63mm and deposited spread and levelled in layers not exc 15cm thick watered and rammed to a true surface. |
| 68 | M&L for 50mm thick cement concrete 1:3:6 type C-1 (using 20mm graded crushed stone aggregate) as in plinth protection laid in alternate bays (n exc 2 sqm each) area with 6mm wide joints and 10mm wide joints between the walls and plinth protection, finished even and smooth without using extra cement, outward slope of not less than 1:12, the joints shall be filled with mastic filling comprising one coat of bitumen 85/25 grade and three parts of sand by weight, complete all as specified. |
| 69 | M&L for preparation of new plastered surfaces on walls and applying three coats of white wash complete all as specified and directed. |
| 70 | S&F Steel wire fabric of weight n.exc 4 kg/sqm fixed complete with wood or steel members. |
| 71 | S&F Pressed steel frames 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed by Engr-in-charge. |
| 72 | M&L for preparation of new or previously untreated surface of steel or iron surfaces of any description over 10cm width or grith and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed by Engr-in-charge. |
| 73 | S&F Factory made 35mm thick, IInd class H.W rail and style plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated, complete all as specified and directed by Engr-in-charge. |
| 74 | M&L for preparation of new or previously untreated wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed by Engr-in-charge. |
| 75 | S&F butt hinges of mild steel cold rolled medium weight of size 100mm, complete all as specified and directed by Engr-in-charge. |
| 76 | M&L for 2nd class H/W plain fillets square rectangular or trangular in section, clean swan secured with nails exc. 13 but n.exc 25 Sqcm in section. |
| 77 | S&F Aluminium alloy, anodised sliding door bolts (300mm long) with hasp, staples (bolt type) and fixing clip of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed, complete all as specified and directed by Engr-in-charge. |
| 78 | S&F Aluminium tower bolt (200mm long), anodised barrel tower bolts of extruded section, complete all as specified and directed by Engr-in-charge. |
| 79 | S&F Aluminium handles cast type, anodised, 150 mm size complete all as specified. |
| 80 | S&F Mild steel cold rolled butt hinges medium weight 100 mm long complete all as specified. |
| 81 | S&F Roof trusses (framed), trussed, purlines, rafters, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel, hollow section square/ rectangular or flat sections) including distance pieces, cleats, MS Plate, welding, bolts etc. |
| 82 | Pre-painted galvalume aluminium zinc coating GI based Corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified. |
| 83 | Pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified. |
| 84 | Chequered coloured cement concrete tiles 30cm x 30cm x 25mm thick, set, with grey cement and pigment, jointed and pointed in neat cement slurry in floors over and incl 20 mm thick screed bed in CM 1:4, complete all as specified and directed. |
| 85 | Formwork to faces of walls or water tank walls complete alll as specified and directed. |
| 86 | M&L for point wiring using FRLS PVC insulated unsheathed /multistranded copper conductor cable 1.5 sq mm drawn through and including PVC Conduit marked and of appropriate size as specified, fixed in surface of wall/ceiling with mild steel sunken box and bakelite sheet 3 mm thick including all fittings such as tees, bend and junction boxes etc complete for following:- Make of Cable :-Havells/Polycab or equivalent Make of Conduit:-As per IS |
| 87 | One light/Fan point controlled by one switch 5 Amps one way using cable (1.5 Sq mm for phase and neutral and 1.5 sq mm earthing) |
| 88 | One 5 Amp socket outlet on independent board. |
| 89 | All as per Item Srl No 86 above but for one socket outlet 15 Amps on Independent board using cable (2.5 Sq mm for Phase & neutral and 2.5 Sq mm for earthing). |
| 90 | S&F Sheet metal enclosure factory made (double door) shutter type for DB SPN, 240 Volts, 8 ways with 200 Amps rated bus bar, neutral link, earth bar complete. |
| 91 | S&F in replacement SPN 40 to 63 Amp, 10KA, 240 Volts. |
| 92 | S&F in replacement MCB SP 5 to 32 Amp, 10KA, 240 Volts. |
| 93 | S&F Switch piano, flush type 5 Amp, One Way. |
| 94 | S&F socket outlet 2-in-1, 3 pin 5 Amp. |
| 95 | S&F Switch piano, flush type 15 Amp, . |
| 96 | S&F socket out let 2 in 1, 5 & 15 Amp flush type. |
| 97 | S&F ceiling rose 3 terminal size 50*65 mm surface type. |
| 98 | S&F LED Lights fitting 1x18 watt,220V, AC Decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. |
| 99 | S & Replacement for angular type Lamp holder PVC policarbonate type with back plate complete all as specified. |
| 100 | Earthing complete with galvanised earth plate electrode 60 cmx 60 cmx 6 mm thick burried directly in ground (earth pit not less than 2.25 mtr deep below GL) with top edge of the plate not less than 1.5M belownormal GL connected to GI wire 4mm as earthing lead by means of nut,bolts and check nut and washer,GI light grade protection pipe 15 mm dia. upto 7.5 m,GI watering pipe 20 mm dia,RCC cover with funnel,excavation in any type of soil,PCC pit charcoal ,salt all as shown in electrical plate No 5 of SSR Part I, including earth test point up to pannel board,all as specified or indicated including testing on completion. |
| 101 | Supply and fixing electric water heater, storage type steel body with copper inner tank and heating element upto 2KW capacity 25 ltr complete with all acessories such as safety valve,thermostate,NRV,connection piece etc. |
| 102 | S& F Exhast fan made of sturdy engineering plastic complete with louvers shutter,voltage 230,50 hz,RPM 1200,Copper winding of sweep 300mm. |
| 103 | S& F LED Street light fitting 35 watt 230 v AC out door type with high pressure die complete with driver,lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with ip 65/66 protection complete. |
| 104 | Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1,5 mtr in depth for laying of cables including getting out in any kind of soil complete all as specified and directed. |
| 105 | Returning filling in including spreading, levelling, and well ramming, in layers not exceeding 25 cm each layer of any kind of soil. |
| 106 | Removing surplus excavated material from site not exceeding 50 mtrs from starting point and depositing where directed at level not exceeding 1.5 mtr above the starting point. |
| 107 | M & L for Sand cushioning for cables all as specified in 19.75 of SSR Part-I. |
| 108 | Material and labour for sub class B brick old size covering laid dry ,flat transversely along the length of cable on sand cushioning with width eqal to the length of the brick complete. |
| 109 | Supply, fixing & laying GI pipe light grade 50mm bore in trench, under floor, wall and on pole for cable protection. |
| 110 | Supply and laying 1100 volts grade PVC insulated heavy duty armoured multistranded aluminium conductor cable of size 6 Sqmm 2.0 core in trenches, through pipe, under culvert or in air complete all as specified and directed. Note:- Earthing work, Sand cushioning and Brick shall be measured and paid separately |
| 111 | M&L for fixing Air termination lightening conductor single pointed copper rod 12mm dia and 300mm long fixed properly on top of the roof of building complete all as specified and directed by Engr-in-charge. |
| 112 | M&L Test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 Nos 8mm dia 25mm long hex head screws all as specified. |
| 113 | M&L for fixing of epoxy electric insulators BMD 40mm for mounting of earth conductor. |
| 114 | Supply and fix Aluminium strip 25mm x 3.15mm complete with saddles and fixing screws etc for roof conductors and down conductors, fitting the strip complete all as specified and as directed. |
| 115 | M&L for tube light grade of 40mm dia for fixing of air termination rod in any indicated situation all as specified. |
| 116 | Earthing complete with galvanised earth plate electrode 600x600x6mm burried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5mtr below normal ground level connected to and including GI earth lead using galvanised iron strip 25x4mm size by means of nuts & bolts, check nuts and washers of galvanised steel including PCC pit of 1:2:4 type B-1 cover reinforced with XPM weight not less than 4kg/Sqm and 6mm dia bar handle, excavation and earth work in hard/dense soil, charcoal dust salt, medium grade GI watering pipe of 20mm dia with funnel and wire mesh and light grade GI protection of 40mm bore from top edge of earth plate upto main distribution board to main switch board all as specified and testing on completion.Note: Item of Earthing includes cost of 7.5m long galvanised iron earth lead 32x6mm size and protection pipe of 40mm bore light grade. |
| 117 | Note:- The contract sum arrived after deduction of amount of Sch of credit as listed in tender Documents. Please Enable Macros to View BoQ information |
