|
| 1 | Taking down chowkat or frame exc 1.5 Sqm but n.exc 4 Sqm each (without taking off shutter from the frame) complete all as specified and directed. |
| 2 | Taking down chowkats or frames n. exc 1.50 Sqm each with shutters (without taking off shutter from the frames) complete all as specified and directed. |
| 3 | Demolition of Brickwork/solid concrete block work built in Cement mortar complete all as specified and directed. |
| 4 | Dismantling unframed wooden work in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section complete all as specified and directed. |
| 5 | Demolition of cement concrete in ground floors and pavings n exc 15cm thickness (below or above ground level) complete all as specified and as directed. |
| 6 | Dismantling plain or corrugated steel sheeting, any guage, thickness incl Nainital, similar pattern as in roof coverings. complete all as specified and directed. |
| 7 | Dismantling floor, hearth , wall tiling including cement mortor bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. |
| 8 | Dismantling of stone slabs and tiles of any description or thickness in floors aprons laid in any mortar complete all as specified and directed. |
| 9 | Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed. |
| 10 | Dismantling boarding any description fixed in any position with nails complete all as specified and directed. |
| 11 | Dismantling of timber scantling 40 sqcm over in section in any position (unframed work) complete all as specified and directed. |
| 12 | Excavation in trenches n,exc 1.5m wide and n,exc 1.5m depth for foundation, etc, n exc 10 sqm on plan and n exc 1.5m depth and getting out in soft/loose soil complete all as specified and directed. |
| 13 | Returning filling in including spreading levelling, watering and well ramming in layers n.exc 25cm thick in soils complete all as specified and directed. |
| 14 | Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed. |
| 15 | M & L for moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed. |
| 16 | M & L for hardcore of broken brick/stone or boulders gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15cm thick, watered and remmed to a true surface,complete all as specified and directed. |
| 17 | M&L PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in foundation filling mass concrete all as specified and directed. |
| 18 | M&L for RCC (nominal mix) 1:2:4 type B (using 20mm graded aggregates) as in foundations, including rafts, footings, foundation beams; plinth beams, lintel beams , roof beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete etc. complete all as specified and directed. |
| 19 | M&L for RCC (nominal mix) 1:2:4 (using 20mm graded aggregates) as in columns, piers , posts etc. complete all as specified and directed. |
| 20 | M&L for RCC (nominal mix) 1:2:4 (using 20mm graded aggregates) as in Beams, cantilevers, bressummers, lintels over 1.5m span etc. complete all as specified and directed. |
| 21 | M&L for fair finished flat formwork to sides of concrete foundations, footings, bases of columns,and soffits (if any) of plinth beams; and similar work; complete all as specified and as directed. |
| 22 | M&L for fair finished square , rectangular or polygonal formwork to sides of pillars, columns, posts, piers etc. complete all as specified and as directed. |
| 23 | M&L for fair finished flat formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers,lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc complete all as specified and as directed. |
| 24 | M&L for mild steel TMT bars 10mm dia and over, cut length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia quality conforming to Fe 500 or Fe-550 as in steel reinforcement for concrete complete all as specified and directed. |
| 25 | All as item No 24 above but 5 mm dia and over up to 10mm dia of steel bars as in stirrups, spacers, rings etc complete all as specified and directed. |
| 26 | Excavation in post holes each n.exc. 0.5 cum in soft/loose soil getting out returning, filling in and ramming earth or broken rubble mixed with earth around in layer n.exc. 25 cm, watering and removing surplus soil to a distance n.exc. 50 mtr and making good surface complete all as specified and directed. |
| 27 | M&L PCC 1:2:4 type B2 (40mm graded aggregate) as in sub base,foundation filling and mass concrete etc.complete all as specified and as directed. |
| 28 | S&F steel work as in tubular , rafters, purlins, posts and similar work (round/square/rectangular shape of pipes as approved) trusses of semi circle/ curved shape up to height 6 mtr including post special shaped washers, gusset plates etc complete using ERW or induction butt welded tubes conformining to IS 1161-1998 garde St-240 complete all as specified and directed. |
| 29 | S&F Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre using Hangers 4 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long including 10mm thick plaster of paris ceiling (Gypsum anhydrous board) fixed in frame work complete all as specified and directed. |
| 30 | M&L for 2nd class hard wood plain fillets. square, rectangular or triangular in section, clean sawn, secured with nails or brads , sectional area exc. 13 and n.exc. 25 sqcm complete all as specified and directed. |
| 31 | S&F 2nd class SW boarding 20mm thick fixed with nails in eaves board planned one side with butt joint complete all as specified and directed. |
| 32 | M&L 2nd class hard wood plain solid straight chowkats and frames wrought framed rebated on the solid ,rounded or chamfered ,put together with glue pinned at joints , supplied and fixed complete all as specified and directed. |
| 33 | S&F 35 mm thk Flush door shutters solid core construction with block board core and plywood face pannels , commercial type on both sides complete all as specified and directed. |
| 34 | S&F 18/19 mm thick block boards grade 1 quality, exterior grade, commercial type fixed with screws to timber frame complete all as specified and as directed. |
| 35 | M&L 12 mm thick Plywood (07 Nos of ply) , grade BWP, type BB, fixed with screws to timber frame work complete all as specified and as directed. |
| 36 | S&F 1.5 mm thick decorative laminates type 1 of surface finish color and pattern as approved fixed with approved adhesive as per manufactures instruction complete all as specified and directed. |
| 37 | S&F SS telescopic channel / ball bearing drawer channel of size 500 mm long complete all as specified and as directed. |
| 38 | S&F W- hinges 75 mm medium weight, stainless steel, and fixed complete all as specified and directed. |
| 39 | S&F W- hinges 125mm, medium weight, stainless steel, and fixed complete all as specified and directed. |
| 40 | S&F 200mm long Brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts complete all as specified and directed. |
| 41 | S&F 100mm long Brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts complete all as specified and directed. |
| 42 | S&F Extruded brass handles, fabricated type polished of size 250 mm complete all as specified and directed. |
| 43 | S&F Extruded brass handles, fabricated type polished of size 150 mm complete all as specified and directed. |
| 44 | S&F Magnet catches for cupboard shutter, brass body and striking plate including letting in all as specified and as directed. |
| 45 | S&F 30mm width of flaps (When open in mm) continuous (piano) hinges, mild steel , bright finish or electro galvanised complete all as specified and directed. |
| 46 | S&F Brass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) of size 300mm long and fixing bolt with rolled or drawn brass bolts and fixed complete all as specified and directed. |
| 47 | S&F factory made uPVC white color Sliding window Two track or openable door area not exceeding 2.00 sqm each made extruded profiles with wall thickness of 2.3mm (+- 0.2mm). Window profile with hollow section with multi chamber, Frame (60mm x 62mm). sash (42mm x 67mm). Sliding Interlock (One vertical length in each shutters) (45.5mm x 28mm). Glazing bead (24.5mmx 16mm) will he mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc.. making arrangement for fixing of hardware. EPDM gasket 1.2 + -0.2mm thick galvanized steel frame (30mm x 21.5mm), Sash (30mm x 18mm), profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners. Hardware : [Touch Lock of zinc alloyed (white powder coated), steel roller system including 5mm thick glazing with selected quality glass, aluminum track on bottom rail for two track sliding frame, wool pine for Sliding sash and interlock.] (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose) etc complete all as specified and as directed. |
| 48 | S&F factory made uPVC white color Sliding window Two track area exceeding 2.00 sqm each made extruded profiles with wall thickness of 2.3mm (+- 0.2mm). Window profile with hollow section with multi chamber, Frame (60mm x 62mm). sash (42mm x 67mm). Sliding Interlock (One vertical length in each shutters) (45.5mm x 28mm). Glazing bead (24.5mmx 16mm) will he mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc.. making arrangement for fixing of hardware. EPDM gasket 1.2 + -0.2mm thick galvanized steel frame (30mm x 21.5mm), Sash (30mm x 18mm), profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners. Hardware : [Touch Lock of zinc alloyed (white powder coated), steel roller system including 5mm thick glazing with selected quality glass, aluminum track on bottom rail for two track sliding frame, wool pine for Sliding sash and interlock.] (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose) etc complete all as specified and as directed. |
| 49 | S&F factory made uPVC white colour fixed window of area exceeding 1.00 sqm but not exceeding 2.00 sqm each made of extruded profiles with wallthickness of 2.3mm(+-0.2mm). Window profile with hollow section with multi chamber. Frame (60mm x 58mm). T profile (Onevertical length in between twoshutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixinghardware and drainage of water etc. making arrangement for fixing of hardware, EPDM gasket. 1.2 +–0.2mm thick, galvanized steel Frame (28mm x21.5mm), T profile (27mm x 17 mrn) to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners- 5mm thick glazing with selected quality glass (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessoriesNet opening will be measured for payment purpose.) |
| 50 | S&F factory made uPVC white colour fixed window of area exceeding 2.00 sqm each made of extruded profiles with wall thickness of 2.3mm(+-0.2mm). Window profile with hollow section with multi chamber. Frame (60mm x 58mm). T profile (Onevertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc. making arrangement for fixing of hardware, EPDM gasket. 1.2 +–0.2mm thick, galvanized steel Frame (28mm x 21.5mm), T profile (27mm x 17 mrn) to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners- 5mm thick glazing with selected quality glass (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories Net opening will be measured for payment purpose.) |
| 51 | M&L for 8 mm thick sheet glass quality and glazing fixed to aluminium frame n.exc 0.50 sqm complete all as specified and as directed. |
| 52 | M&L for 8 mm thick sheet glass quality and glazing fixed to aluminium frame exc 0.50 sqm complete all as specified and as directed. |
| 53 | M&L for 6 mm thick sheet glass quality and glazing fixed to any metal / non metal frame of any size complete all as specified and as directed. |
| 54 | M&L for 4.80 mm thick frosted sheet glass quality and glazing fixed to aluminium frame n. exc 0.50 sqm complete all as specified and as directed. |
| 55 | M/L precast cement concrete block massonry with solid blocks exc 10 cm in width and settings in CM 1:6 type C1 1:3:6 (20mm graded aggregate) complete all as specified and directed. |
| 56 | M/L precast cement concrete block massonry with solid blocks nexc 10 cm in width and settings in CM 1:4 type C1 1:3:6 (20mm graded aggregate) complete all as specified and directed. |
| 57 | S&F 3 mm thick Aluminium composite panel (ACP) sheeting having coil thickness 0.50 mm coloured as per approved colour by GE including using steel cleat, frame, sealing and backup material as in wall cladding complete all as per manufacturers instruction and complete all as specified and directed. Make: Aludecor / Eurobond/ Alstrong / Alstone / Alutech Panels). |
| 58 | S&F pre-painted Galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tenssile strength of 550 Mpa as in roof covering / cladding including fixing with self driving machine made screws with washers and fitting of same manufacture of approved profile, complete all as specified and directed. |
| 59 | S&F pre-painted Galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tenssile strength of 550 Mpa as in roof covering including fixing with self driving machine made screws with washers and fitting of same manufacture of approved profile, shape and colour complete all as specified and directed. |
| 60 | M&L for 25 mm thick Cement concrete1:2:4 type B-1 (20mm graded aggregate) used over sub base to recd floor tiles complete all as specified and directed |
| 61 | M&L for Virified Ceramic tiles 9-10 mm thick dark shade/double charged/ultracherged (square/rectangular) polished, area of each tiles exceeding 0.42 sqm but n.exceeding 1.00sqm as in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and laid over and including15 mm thick cement screed bed in CM 1:6 complete all as specified and directed. |
| 62 | All as per Item No 61 above here–in–before but on vertical surfaces such as skirtings and risers to steps etc laid over and including 10mm thick rendering in CM 1:4 as in backing coat complete all as specified and directed. |
| 63 | M&L for vitrified ceramic tiles dark shed (exterior grade), 10 mm thick(square /rectangular), polished, area of each tile n exc 0.36 sqm in floor etc , laid over 15 mm thick screed bed 1:6 ,set and jointed in neat cement slurry and pointed in white/coloured cement to match complete all as specified and as directed. |
| 64 | M&L for 18/20mm thk granite slab (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and incl pointing in white cement (1:2) using marble dust with admix ture of pigment to match with shade of granite over and including 20 mm thick cement screed bed in CM 1:4 complete all as specified and as directed. |
| 65 | M&L for rounding to edges of stone slabs one edge, such as in steps, cooking plateform, and other similar situation. |
| 66 | M&L for 10 mm thick plaster in cm (1:6) on fair faces of brick or concrete surfaces including finishing even & smooth without using extra cement complete all as specified and as directed. |
| 67 | M&L Rendering, 15 mm thick in CM 1:4, in two layers, first 5 mm thick with approved Water proofing compound @ 3% by the weight of cement or as per manufacturers instructions over a coat of 10 mm thick base coat finished even and smooth complete all as specified and as directed.Note : WPC shall be measured and paid separately. |
| 68 | Supply only Integral waterproofing compound. |
| 69 | M&L for 110 mm PVC (SWR) pipes single socketed in any length with rubber ring joints ,laid in trenches or in floors complete all as specified and as directed. |
| 70 | S&F PVC (SWR) bends 110mm dia complete all as specified and as directed. |
| 71 | Supply and Fix half round PVC rain gutter of dia 180 mm including clamps, bolts and nuts complete all as specified and as directed, |
| 72 | M&L 75mm thick cement concrete 1:4:8, type D2 using (40mm graded aggregate) as in sub base. |
| 73 | M&L for 75 mm thick cement concrete 1:3:6, type C-2 (using 40mm graded agg) as in plinth protection finished even and smooth without using extra cement.(incl necessary joint filling with mixture of paving bitumen & sand in 1:3). |
| 74 | S&F MS framed work such as grills, gratings, etc with ends of bars, shouldered and/ or riveted or forged into spikes framed guard bars, barred iron doors, ladders, framed balusters, walk way, railing and framed work of water tanks and similar work confirming to Fe 290 Gde E-165 complete all as specified and as directed. |
| 75 | S&F POP (Gypsum) cornice moulding of 100mm wide as in facades and soffit design approved by GE complete all as specified and as directed. |
| 76 | M&L for preparation of old painted concrete/plastered surfaces of any description , over 10 cm in width or girth, not otherwise described and applying 1mm thick of white wall care putty or cement paste to achieve smooth surfaces and applying two coat of plastic emulsion paint of approved shade/tint over a priming coat paints plaster complete all as specified and as directed. |
| 77 | M&L for preparation of newly concrete/plastered surfaces/gypsum board of any description , over 10 cm in width or girth, not otherwise described and applying 1mm thick of white wall care putty or cement paste to achieve smooth surfaces and applying two coat of plastic emulsion paint of approved shade/tint over a priming coat paints plaster complete all as specified and as directed. |
| 78 | M&L for preparation of new steel surfaces of any description , over 10 cm in width or girth, not otherwise described and applying two coat of synthetic enamel paint over a coat red oxide primer complete all as specified and as directed. |
| 79 | M&L for preparation of new or previously untreated surfaces of wood and wood based materials of any description not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint over a coat of pink primer all as specified and as directed. |
| 80 | M&L for preparation of plastered or unplastered old decorated surfaces of walls by washing rubbing down and stopping of any external painted surfaces and priming with alkali resistant primer paint applying two coats of weather coat exterior paint with roller incl filling of holes and cracks with suitable material like cement or plaster of paris etc complete all as specified and as directed. |
| 81 | M&L for preparation of new plastered/concrete surfaces of walls and priming with alkali resistant primer paint applying two coats of weather coat exterior paint with roller etc complete all as specified and as directed. |
| 82 | M & L 100 mm Plain Cement concrete 1:4:8 type D2 (40mm graded aggregate) as in sub-base of floor complete all as specified and as directed. |
| 83 | M&L for walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in CM 1:6 complete all as specified and as directed. |
| 84 | Extra over stone walling for hammer dressing to face stones and dressing with maximum depression from straight edge held against the dressed surface to face beds and joints, as specified, of random rubble walling, uncoursed or brought upto courses complete all as specified and as directed. |
| 85 | M&L for Raised pointing to random or polygonal rubble, uncoursed or brought upto courses in cement mortar 1:3 complete all as specified and as directed. |
| 86 | M&L for PCC1:2:4 type B-1 (20mm graded stone agg) as in coping, roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and as directed. |
| 87 | M&L for PCC (1:3:6), type C2 (using 20mm graded stone aggregate) as in foundation filling and mass concrete including all necessary form work complete all as speciified and directed. |
| 88 | M&L for preparation of new steel surface of any description over 10cm in width or girth and applying two coat of synthetic enamel paint over one coat of red oxide/zinc chrome primer complete all as specified and directed. |
| 89 | Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and as directed. |
| 90 | M&L Non skid Ceramic Parking tiles Dark shade 15 mm thick as per approved (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed |
| 91 | S&F powder coated (min powder coating 50 micron) anodised aluminium frame for doors, windows , ventilators and partition plain or sliding type with one or more rebates including joining cleat for fixing etc complete all as specified and as directed |
| 92 | S&F powder coated(powder coating min 50 micron) anodised door shutters , aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, rubber neoprene packing , handles 2 nos in each door , hinges , anodised aluminium snap beading screws etc complete all as specified and as directed. |
| 93 | M&L for PCC 1:3:6 type C1 (using 20mm graded crushed stone aggregate) as in bond stone complete ass as specified and directed. |
| 94 | Material & Labour for preparation of new plastered surface and applying Two or more coats (over 1 mm thick wall care putty ) of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and as directed. |
| 95 | M & L for Forming embankments including raising (or lowering) earth, spreading in layers n exc. 30 cm thick; watering, ramming/rolling and finishing to required size, shape, etc., n exc. 1.5 m high from base of Solids. |
| 96 | S&F 2 mm thick fibre reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof , wall etc complete all as specified and as directed |
| 97 | M&L for roof truss (framed) trussed, purlin etc of angle or other section for refixing of sheets and similar works complete of Gde Fe-290 (Gde E-165) all as specified and directed. |
| 98 | M & L for Moorum/red bajri (As per approved) filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and as directed. |
| 99 | Taking down carefully copper/aluminum point wiring light/fan/sockets out let/power point complete (fittings such as switches, sockets, ceiling rose, pendent holders, light fittings etc. are to be measured separately) and/or drawing out from existing conduit/batten and making good disturbed surface of walls/floors/ceiling, complete all as specified. |
| 100 | Material and labour for Point wiring with 1.50 Sqmm single core PVC insulated , unsheathed cable FRLSH, 1100 volt grade with multi stranded copper conductor drawn through and incuding medium grade, ISI marked, PVC conduit not less than 20 mm dia with accessories, PVC conduit on wall/ceiling and incuding provision of 1.50 Sqmm single core PVC insulated , unsheathed cable FRLSH, 1100 volt grade with multi stranded copper conductor green colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including mild steel sunken box/metal flush box with suitable modular or pressed steel terminal boxes made out of 1.6 mm thick mild steel sheet metal conforming to IS-5139(pt-I) of 1969 and IS:14772-2000 with earth dolly and coated with two coats of anti corrosive paint over a coat of red oxide primer both internally and externally including provision of new 3 mm thick plastic laminated sheet top cover for housing the switches , socket outlets, fan regulators etc. with brass screws and brass washers and making good the disturbed surfaces as per existing for one light/fan point controlled by one switch. |
| 101 | Description all as per Srl item No 100 here in before but for socket outlet point 5 Amp on same board. |
| 102 | Description all as per Srl item No. 100 here in before but for socket outlet point 5 Amp on Independent board. |
| 103 | Description all as per serial item No 100 above but with 4 sqmm cable for 3 pin 15 Amps switch socket outlet (Power point) complete all as specified. |
| 104 | Supply and fixing modular switch 1 way 6 A with cover plate and frame 230/250 volt , AC supply, ISI Marked, with white cover plate with frame complete all as specified and directed. |
| 105 | Supply and fixing modular sockets with cover plate and frame 6A 2/3 pin combined 2 module 230/250 Volts, 50 Hz , AC supply, ISI Marked, with cover plate complete all as specified and directed. |
| 106 | Supply and fixing modular switch 1 way 16 A with cover plate and frame230/250 volt , AC supply, ISI Marked, with white cover plate with frame complete all as specified and directed. |
| 107 | Supply and fixing modular sockets 6A/16A 2/3 pin combined 2 module with cover plate and frame 230/250 Volts, 50 Hz , AC supply, ISI Marked, with white cover plate with frame complete all as specified and directed. |
| 108 | Supply and fixing round shape 6 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. |
| 109 | Supply and fixing round shape 12 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. |
| 110 | Supply and fixing round shape 15 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. |
| 111 | Supply and fix Flexible LED strips complete all as specified and direcetd. |
| 112 | S & F LED light fitting /1X20W Focus down light white/warm white connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. |
| 113 | Supply and fixing LED batten fittings 1x 20 Watt complete including LED light driver, holder, LED lamp and connection up to ceiling rose with three core wire fixed to wall with 2 nos PVC block of suitable size including taking down old unserviceable one complete all as specified and directed. . |
| 114 | Supply and fixing ceiling rose surface bakelite 65x50mm, 3 terminal complete all as specified and directed. |
| 115 | S & F Exhaust fan 230 volts , 300mm,plastic body including making all electric connection complete all as specified and as directed including cutting of hole on wall and makng good disturbed surface of wall and outer wooden box for fan fix on wall complete all as specified and directed. |
| 116 | Supply and fix in repairs MCB DB 4 way vertical sheet metal enclosure TPN 415 volts, 50 Hz, with IP-43 protection, double door with 200 Amps standard bus bar of suitable size and common neutral link all enclosed in standard sheet flush mounting complete all as specified. |
| 117 | Supply and fix in repair MCB Distribution board , 240 volts single pole and neutral ,double door, sheet steel, enclosure powder coated with 100 Amps rated busbar with neutral link, 12 ways , fixed on wall duly grouted in solid block wall or on wooden board with electrical connection, including taking down complete all as specified and directed. |
| 118 | Supply and fix MCB DP, 240 Volts, 40 Amps, 10 kA rupturing capacity 'C' series complete all as specified and directed. |
| 119 | Supply and fix MCB TPN, 240 Volts, 100 Amps, 10 kA rupturing capacity415 Volts complete all as specified and directed including taking down old one all as specified and directed. |
| 120 | Supply and fix in repairs MCB, single pole 240 volts 6 to 32 Amps capacity fixed in DB's.complete all as specified and directed. |
| 121 | M & L Sub main wiring with two run single core 6 Sqmm FRLSH copper conductor cable PVC insulated, unsheathed, 1100 V including 20 mm dia PVC conduit on wall/ceiling in PVC conduit, medium grade ISI marked with all accessories such as Tees, elbows, junction boxes etc, as required fixed on wall along with one run of 6 Sqmm single core PVC FRLSH insulated unsheathed copper conductor cable as continuous earth wire and connecting to existing main switch board / distribution board and testing on completion including taking down old wiring etc complete all as directed. Note: (i) Two runs of 4 sqmm and one run of 6 sqmm cable and one run of PVC conduit shall be measured as one RM. (ii) Cutting of chases in the wall of appropriate size shall be carried out with electric cutter machine . (iii) Necessary plastering in the disturbed surface of wall and distempering /white washing to match the existing colour shall be included in the unit rate quoted. |
| 122 | Material and labour for earthing complete with galvanised steel earth plate electrode 60 Cm X 60 Cm X 6 mm buried directly in ground vertically to a depth notless than 2.25 mtr deep below ground level with top edge of earth plate at a depth not less than 1.5 m below normal ground level connected to galvanised earth lead wire 4.0 mm dia by means of bolts, check nuts and washers ,galvanised steel and protected by GI pipe 15 mm bore light grade & connected to main switch board or main control board as directed and including concrete pit in PCC (1:3:6) type C1, precast RCC (1:2:4) type B1 cover slab 30 cm X 30 cmX 5 cm with 10mm dia TMT bars 8 cm C/c both ways and one handle for lifting made out of 8 mm dia TMT bar, funnel, wire mesh, 20mm bore galvanised iron pipe (medium grade) for watering, charcoal or coke and salt in alternative layers, necessary excavation and earth work in any type of soil and including necessary testing complete all as shown in Electrical Plate No 3 of SSR part -I. Please Enable Macros to View BoQ information |
