|
| 1 | Dismantling all types of plain cement concrete works, stacking serviceable materials at site and removing rubbish as directed within a lead of 75 m. in ground floor including roof.above 150 mm. thick |
| 2 | Dismantling R.C. floor, roof, beams etc. including cutting rods and removing rubbish as directed within a lead of 75 m. including stacking of steel bars in ground floor including roof. |
| 3 | Supplying labours for taking out old paver blocks carefully,stacking the same in proper stack and depositing the spoils as directed within a lead of 150 m. |
| 4 | Filling in foundation or plinth by fine sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation with water, ramming complete including the cost of supply of sand. (payment to be made on measurement of finished quantity) |
| 5 | Supplying and laying Polythene Sheet (150gm / sq.m.) over damp proof course or below flooring or roof terracing or in foundation or in foundation trenches. |
| 6 | Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor) 25 mm to 30 mm shuttering without staging in foundation. |
| 7 | Provide Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction. For works in foundation and upto roof of ground floor/upto 4 mTor steel SAIL/ TATA/RINL |
| 8 | Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement,if any, in gound floor as per relevant IS codes. Pakur Variety |
| 9 | Ordinary Cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement,if any, in gound floor as per relevant IS codes. Pakur Variety |
| 10 | Carefully lay old paver blocks in line and level to match with existing paved surface including providing bedding layer with minimum sand (50 to 80 mm avg thk) over hard and compacted base & completed by heavy duty vibretor plate compaction (joints filled with fine sand ) as per specification including all lead,lifts,materials,labours etc comlete in all respect. |
| 11 | Cutting to requisite length or shape departmental R.S. joists, channels, angles, tees, plates etc.(payment to be made on area of cut surface) |
| 12 | Labour for hoisting and placing in proper position (up to 1st floorlevel) departmental R.S. joists, channels, angles. Tees, plates etc.including fitting and fixing same with bolts and nuts, if necessary(but excluding cost of such bolts and nuts) |
| 13 | M.S. structural works with hollow sections (square or rectangularshape) conforming to IS: 806-1968 & IS:1161-1998) connected toone another with bracket, gusset, cleat as per design, drawing &direction of Engineer-in-Charge complete including cutting torequisite shape & size, fabrication including metal arc weldingconforming to IS: 816-1969 & IS: 9595 using electrodes of approvedmake and brand conforming to IS:814- 2004, haulage, hoisting anderection all complete.The rate includes the cost of all M.S. Hollow section, allconsumables such as electrodes, gas and hire charges of all toolsand plants and labour reqired for execution and all incidentalchages (such as electricity, labour insurance) etc. complete.Payment to be made on the basis of calculated weight of structuralmemebrs of MS Holow Section as specified in relevent IS code infinished work. Payment for gusset, bracket, cleat may be made byadding the actual weight of such items with weight of finishedstructural members. The rates are considered for a hight of erection8 m. / 2nd floor level from the ground. Add 1.5 % extra over the ratefor each additional floor or 4m. beyond the initial 8 m. or partthereof.For other Structural works like galleries etc. |
| 14 | M.S. structural works in columns, beams etc. with simple rolled structural members (e.g. joists, angle, channel sections conforming to IS: 226, IS: 808 & SP (6)- 1964 connected to one another with bracket, gussets, cleats as per design, direction of Engineer-in- charge complete including cutting to requisite shape and length, fabrication with necessary bolting, metal arc welding conforming to IS: 816- 1956 & IS: 1995 using electrodes of approved make and brand conforming to IS:814- 1957, haulage, hoisting and erection all complete. The rate includes the cost of rolled steel section, consumables such as electrodes, gas and hire charge of all tools and plants and labour required for the work including all incidental chages such as electricity charges, labour insurance charges etc. Payment to be made on the basis of calculated weight of structural members only in finished work as per IS specified weight. Payment for gusset, bracket, cleat, rivets, bolts and nuts may be make by adding the actual weight of such items with the weight of finished structural members or 7% of weight for finished structural members weighing not less than 22.5 Kg. / m. or 15 % of weight for finished structal members weighing less than 22.5 Kg. / m. may be increased allow for bracket, cleat, rivet, bolts and nuts etc. and no seperate payment being made for these items, as per direction of Engineer In Charge. The rates are considered for a height of erection 8m. / 2nd floor level from the ground. Add 1.5% extra over the rate for each additional floor or 4m. beyond initiial 8m. or part thereof.For structural members of specified sections weighing less than 22.5 Kg./m |
| 15 | Supplying fitting and fixing I.R.C. fabric mesh with covering battens including cost of screws etc complete (excluding the cost of battens).In ground floor. 75mm x 75mm x 2.7mm x 2.7mm. |
| 16 | Supplying & fixing of Raised Pavement Markers / Road Studs / Cats Eye made of polycarbonate moulded body and reflective panels with microprismatic lens capable of providing total internal reflection of the light entering the lens face which shall support a load of 13635 kg tested inaccordance to ASTM D 4280 Type H and complying to clause no 804 of MoRT&H's specification for Road &Bridge Works (Fifth Rev.). Marker height shall not be less than 10 mm and shall not exceed 20 mm, widthshall not exceed 130mm and with minimum reflective area of 13 sq.cm. on each side and slope to the base shall be 35 ± 5 degree. Fixing will bewithout nails but by using epoxy resin based adhesive as per manufacturer's recommendation including site clearance etc. and complete as directed by the Engineer in Charge .The contractor will have to provide a test certificate from a reputable national/international laboratory conforming the above specifications. |
| 17 | Brick work with 2nd class bricks in cement mortar (1:6) In foundation & plinth |
| 18 | Provide and lay Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface]15 mm. thick plaster with 1:6 Cement morter |
| 19 | Provide and lay Neat cement punning about 1.5mm thick in wall,dado,window sill,floor etc.Note: cement 0.152 Per Cum per 100 sq. Mtr. |
| 20 | Providing & applying 1 coat of road marking primer for concrete surface of approved make to receive Thermoplastic paint after necessary brushing & cleaning of the surface etc. with the help of templates of different shapes & sizes as per instruction of Engineer -In-Charge. |
| 21 | Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads. On Bituminous surfaceProviding and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35. The finished surface to be level, uniform and free from streaks and holes complete as per Clause 803 of Specifications for Road & Bridge Works of MoRT&H (5th Revision). |
| 22 | Removal of rubbish,earth etc. from the working site and disposal of the same beyond the compound, in conformity with the Municipal /Corporation Rules for such disposal, loading into truck and cleaning the site in all respect as per direction of Engineer in charge |
| 23 | Applying epoxy based reactive joining agent for joining the old concrete with fresh concrete to be applied within manufacturer's specified time as per manufacturers specification. (0.4 Kg / m² of concrete surface).Applicable only when the full diameter of reinforcement steel is exposed. |
| 24 | Hire charges of Earth movers / Excavator -cum -loader for 8 hours. including one no operator , one no. helper ,fuel etc. The rate inclusive of all expenses etc complete but excluding G.S.T. |
| 25 | Cutting / cleaning / removing jungles, including uprooting / removing of rank vegetation, cutting gran, bush wood cutting gran, bush wood cutting / removing small tree saplings or branches of trees falling under the cutting area at different area of dock and removing spoil up to a distance of 50 m outside the periphery of the area cleared as per direction including all lead, lifts cutting. Instrument, labour etc. complete in all respect. |
| 26 | Supply of daily labour for various non measurable works like segregating and stacking of serviceable materials like paver blocks , stone sets , steel materials etc. |
| 27 | Fixing S.H 90 lbs (rail) 1.50 m in length after cutting, carrying (within 5 km) and fixing in line and level as per the direction of Engineer- in -charge.( The rate is inclusive of the cost of carrying , loading ,unloading ,cutting the rails and fixing the same but excluding the cost of excavating foundation , concreting and painting.)Rail will be supply by KoPT. |
| 28 | Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.(This item is applicable to new work or old work when the original surface has been exposed by removal of old paint.) |
| 29 | Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces bysand papering etc.(This item is applicable to new work or old work when the original surface has been exposed by removal of old paint.) |
| 30 | Provide and paint with best quality synthetic enamale paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface if necessary.On timber plastered, steel or other metal surface with high gloss of approved quality.Two coats (with any shade except white) on steel surface.With hi-gloss of approved quality |
| 31 | Two coats on timber or plastered surface (with any shade except white) With super gloss (hi-gloss) |
| 32 | Cutting of branches of trees shrubs and trimming of grass and weeds Cutting of branches of trees and shrubs from the road way or with in R.O.W including disposal of wood and leaves to suitable location as pertechnical specification Clause 1914 for Rural Roads of MORD. |
| 33 | Supply Air Compressor Machine including labour ,operator, fuel permit etc. for 8 hours at desired location all complete. |
| 34 | Supplying, fitting and fixing retro-reflective warning & regulatory sign with imported reflective sticker of approved quality for lettering direction, arrow,symbol etc. pasted on 14 S.W.C plain galvanised steel of TATA make having clean cut edge & radiuses at all corners painting two coats of synthetic enamel paint over a coat of priming on both sides of the G.I sheet by spray painting with necessary bolting etc. The rate includes cost of reflective sign sticker, G.I sheet, fitting fixing , hoisting & placing in position on steel frame work with necessary tack welding in bolting complete as per approved drawing etc. & direction of Engineer-in-charge but excluding the cost of steel frame.a) Retro reflective sign on one side. Please Enable Macros to View BoQ information |
