Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Surface Dressing of the ground in any kind of soil including removing vegetation inequalities not exceeding 15 cm depth and disposal of the rubbish within a lead upto75 m as directed. |
| 2 | Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing, spreading or stacking the spoils within a lead of 75 m. as directed. The item includes necessary trimming the sides of trenches, leveling, dressing and ramming the bottom, bailing out water as required complete. Depth of excavation not exceeding 1.5 m. |
| 3 | Earth work in filling in foundation trenches or plinth with good earth, in layers not exceeding 150 mm. including watering and ramming etc. layer by layer complete. (Payment to be made on the basis of measurement of finished quantity of work) With earth obtained from excavation of foundation. |
| 4 | Filling in foundation or plinth by fine sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation with water, ramming complete including the cost of supply of sand. (payment to be made on measurement of finished quantity) |
| 5 | Post Construction: Anti-termite treatment to the junction of wood work and masonry walls with chemical emulsion by admixing chloropyrofos emulsifiable concentrates (1% concentration) with water by weight including spraying at the points of contact with the adjoining masonry by drilling 6m. dia holes at a downward angle of about 45 degree at the junction of woodwork and masonry and squirting chemical emulsion into these holes at the rate of half litre per hole. The entire work is to be carried out as per specification of Code I.S.-6313 (Part-III)-1981. The shutters are to be sprayed with emulsion. on both sides. All wooden fixtures like almirahs, racks etc. are also to be throughly sprayed with chemical emulsion. (Payment will be made on the basis of outside measurements of doors and windows) |
| 6 | Dismantling all types of masonry excepting cement concrete plain or reinforced, stacking serviceable materials at site and removing rubbish as directed within a lead of 75 m. |
| 7 | In ground floor including roof. |
| 8 | Dismantling all types of plain cement concrete works, stacking serviceable materials at site and removing rubbish as directed within a lead of 75 m . Up to 150 mm. thick |
| 9 | In ground floor including roof. |
| 10 | Dismantling R.C. floor, roof, beams etc. including cutting rods and removing rubbish as directed within a lead of 75 m. including stacking of steel bars. |
| 11 | In ground floor including roof. |
| 12 | Dismantling carefully terraced floor only (including floor finish if any) or lime terracing in ground floor roof and removing rubbish as directed within a lead of 75 m. |
| 13 | In ground floor including roof. |
| 14 | Dismantling artificial stone flooring up to 50mm. thick by carefully chiselling without damaging the base and removing rubbish as directed within a lead of 75 m. |
| 15 | In ground floor including roof. |
| 16 | Stripping off worn out plaster and raking out joints of walls, ceilings etc. up to any height and in any floor including removing rubbish within a lead of 75m as directed. |
| 17 | Cutting chase up to 125 x 150 mm. and subsequent mending of damages. |
| 18 | In brick wall [Cement-3.6 Kg/Mtr] |
| 19 | Cutting holes and subsequent mending good damages Diameter up to 150 mm. |
| 20 | In brick work [Cement-4.0 Kg/Mtr] |
| 21 | Single Brick Flat Soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand. |
| 22 | Ordinary Cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement, if any, in ground floor as per relevant IS codes Pakur Variety.In Ground floor. |
| 23 | Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes.Pakur Variety |
| 24 | In ground floor including roof. |
| 25 | Hire and labour charges for shuttering with centering and necessary staging up to 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (up to roof of ground floor). |
| 26 | 25 mm to 30 mm thick wooden shuttering as per decision & direction of Engineer-In-Charge. |
| 27 | In ground floor including roof. |
| 28 | Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc. initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction. Tor steel/Mild Steel (SAIL/TATA/RINL) |
| 29 | For works in foundation, basement and up to roof of ground floor/up to 4 m. |
| 30 | Brick work with 1st class bricks in cement mortar (1:6). |
| 31 | In foundation and plinth |
| 32 | In superstructure, ground floor |
| 33 | 125 mm. thick brick work with 1st class bricks in cement mortar (1:4) |
| 34 | In Ground Floor. |
| 35 | Cleaning the concrete surface by removing dirt and debris, marking defective locations and removing loose concrete by careful stripping untill hard surface is exposed,cutting the concrete to regular shape, wire brushing the exposed surface and removing debris from site complete as per direction of the Engineer - in - Charge. |
| 36 | Applying epoxy based reactive joining agent for joining the old concrete with fresh concrete to be applied within anufacturer's specified time as per manufacturers specification. (0.4 Kg / m² of concrete surface) Note: Applicable only when the full diameter of reinforcement steel is exposed. |
| 37 | Applying 2 coats of bonding agent with synthetic multi functional rubber emulsion having adhesive and waterproofing properties by mixing with water in proportion (1 bonding agent : 4 water : 6 cement) as per Manufacturer's specification. |
| 38 | Cleaning the exposed reinforcement preferably upto full diameter by wire brush, applying two coats of polymer based rust removing compound left for 24 hours, removing the coating and then applying two(2) coats of polymer modified anti corrosive protective coating formulated to inhibit the corrosion of reinforcement as per manufacturer's specification] |
| 39 | Repairing cracks in floor with cement mortar (1:2) with necessary pigment to match with existing works, including prior cutting and cleaning the cracks as directed. |
| 40 | Repairing crack in wall by cement grouting (1 : 2) including widening the crack on the surface (into V section) cleaning and packing the same with cement mortar (1 : 2) and finishing off to match with adjacent surface. (Cement-69 Kg/100 m) |
| 41 | Roof treatment by application of non toxic polyurethane modified acrylic based single component (P U roof Coat) solvent free, cold applied polyurethane modified elastomeric waterproofing membrane with excellent UV resistant capacity as per ASTM D 6083 ( a water based 100% acrylic elastomeric emulsion polymer latex coating used as protective coating coating for roofs) after preparing the surface by cleaning and repairing the roof cracks by cement and sand morter(1:4), preferably with antishrinkage mortar (to be paid seperately) if any, apply two coats along with a Priming coat (two coats of P U Roof Coat and one coat of primer coat compatible Geotextile Fleece, including the cost of primer coat and base preparation , tools & plants but excluding the cost of scaffolding and stagging complete as per direction of Engineer-in -charge, (Note: If Geotextile Fleece not used, the rate would be reduced by Rs. 5/- per Sqm. |
| 42 | Washing and cleaning with oxalic acid powder using 33gms./Sqmtr. |
| 43 | b) Floor / dado other than marble. |
| 44 | Artificial stone in floor, dado, staircase etc. with cement concrete (1:2:4) with stone chips, laid in panels as directed with topping made with ordinary or white cement (as necessary) and marble dust in proportion (1:2) including smooth finishing and rounding off corners including raking out joints or roughening of concrete surface and application of cement slurry before flooring works using cement @ 1.75 kg/sq.m all complete including all materials and labour. 3 mm. thick topping (High polishing grinding on this item is not permitted with ordinary cement). Using grey cement25 mm. thick. |
| 45 | In ground floor. |
| 46 | Supplying dividing strip fitted and fixed with cement mortar (1:3) in mosaic or patent stone floor, dado etc. complete as per direction of the Engineer-in-charge.Glass - 3mm. thick25 mm. wide strip |
| 47 | Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile &finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive& grout materials etc. |
| 48 | Wall :- With Sand Cement Mortar (1:3) 15 mm thick& 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m& joint filling using white cement slurry @ 0.20kg/Sq.m. Area of each tile upto 0.09 Sq.mOther than Coloured decorative including white. |
| 49 | In Ground Floor. |
| 50 | Floor:- With Sand Cement Mortar (1:4) 20 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m. Area of each tile upto 0.09 Sq.m Other than Coloured decorative including white |
| 51 | In Ground Floor. |
| 52 | Supplying, fitting and fixing Black Stone slab used in Kitchen slab, alcove, wardrobe etc. laid and jointed with necessary adhesive Cement mortar (1:2) including grinding or polishing as per direction of Engineer-in -Charge Slab Thickness above 25 mm and upto 37.5 mm |
| 53 | In Ground Floor. |
| 54 | Labour for Chipping of concrete surface before taking up Plastering work. |
| 55 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary.[Excluding cost of chipping over concrete surface] |
| 56 | With 1:4 cement mortar 10 mm thick plaster |
| 57 | In Ground floor |
| 58 | With 1:6 cement mortar In Ground floor |
| 59 | 20 mm thick plaster |
| 60 | 15 mm thick plaster |
| 61 | Rendering the Surface of walls and ceiling with White Cement base WATER PROOF wall putty of approved make & brand.(1.5 mm thick) |
| 62 | in ground floor |
| 63 | Neat cement punning about 1.5mm thick in wall, dado, window sill, floor etc. |
| 64 | Two point nose steel handle including fitting and fixing. |
| 65 | Steel peg stay 300 mm long including fitting and fixing. |
| 66 | M.S. or W.I. Ornamental grill of approved design joints continuously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugs.Grill weighing above 10 Kg./sq.mtr and upto 16 Kg./sq. mtr. |
| 67 | In ground floor |
| 68 | Welding in M.S. structural work with gas or electric. |
| 69 | Tack weld |
| 70 | Continuous weld |
| 71 | Supplying fitting and fixing door frame with M.S. angle as per drawing & direction of required section. The holes for counter sunk machine screw & nuts will be such as to fit 8 to 10 mm Iron screw. The counter sunk nut to be welded . The nuts are to be welded after careful checking with screw. All welding spots should be properly filed or rounded smooth including cost of welding hinges for hinge cleats , lugs for hasp bolt, socket bolt etc. and necessary M.S. clamps of 25mm x 6mm flat 225mm long as per direction welded to the frame fitted and fixed in position excluding cost of concrete. (Weight of frame shall be calculated for the M.S. sections of frames. Payment of butt hinges, clamps, hasp bolt, socket bolts, screws etc. will be paid separately.) |
| 72 | Supplying, fitting and fixing windows and ventilators with or without integrated grills conforming to IS 1038-1975 and manufactured from rolled steel sections conforming to IS 7452-1974 with non-friction projecting type, box type hinges, glazing clips, lugs locking bracket, handle plate etc, including hoisting in position, straightening if required, fixing lugs in cement concrete ( 1:2:4) with stone chips 20 mm down cutting holes and mending good damages to match with existing surface complete in all respect excluding glazing. (a) Openable steel windows as per IS sizes with side hung shutters and horizotal glazing bars. |
| 73 | Supplying best Indian sheet glass panes set in putty and fitted and fixed with nails and putty complete. (In all floors for internal wall & upto 6 m height for external wall)i) 3 mm thick (weighing 7.4 kg/Sq.m) |
| 74 | Supplying fitting approved type ventilator in position after cutting holes in walls setting in cement mortar mending damages to wall and plaster and two coats of paint of approved brand of any shade. Payment of mending gooddamages of wall & plaster and painting to be made separately.(a) R.C.C ventilator of 20 mm. thick(i) Upto 0.10 sq.m. area |
| 75 | Supplying 1.5mm thick M.S. sheet fitted and fixed on one or both faces of M.S./ W.I. gate etc. with point welding at not more than 150mm apart complete in all respect as per design including cost of all labour and materials. |
| 76 | M.S. structural works in columns, beams etc. with simple rolled structural members (e.g. joists, angle, channel sections conforming to IS: 226, IS: 808 & SP (6)- 1964 connected to one another with bracket, gussets, cleats as per design, direction of Engineer-incharge complete including cutting to requisite shape and length, fabrication with necessary bolting, metal arc welding conforming to IS: 816- 1969 & IS: 1995 using electrodes of approved make and brand conforming to IS:814- 2004, haulage, hoisting and erection all complete. The rate includes the cost of rolled steel section, consumables such as electrodes, gas and hire charge of all tools and plants and labour required for the work including all incidental chages such as lectricity charges, labour insurance charges etc. |
| 77 | Labour for taking out door and window frame including shutter for repair or replacement of different parts of the frame & refixing the same including mending good all damages complete. (Concrete and brick work for mending damage will be paid separately) (Upto area 2.5 Sqm) |
| 78 | Taking out shutter of door and window, dismantling by parts (for repair or replacement of damaged parts), reassembling and refitting and rehanging same with old fittings but with new screws as necessary. . |
| 79 | Supplying, Fitting & Fixing Factory made P.V.C. door frame of size 50 mmx47 mm with a wall thickness of 5 mm, made out of extruded 5 mm, PVC sheet miter cut at two corners and joined with two nos of 1.5 mm long brackets of 15 mm x15 mm M.S. square tube. The two vertical door profiles are to be reinforced with 19 mmx 19 mm M.S. Square tube of 19 gauge, weather seal to be provided throughout the frame. The door frame shall be fixed with the wall using 65/100 mm long M.S. Screws through the frame by using P.V.C fasteners. A minimum of 4 Nos of screws to be provided for each vertical member and minimum 2 Nos for horizontal member etc. complete as per Manufacturer’s specification and direction of Engineer-in-Charge. All floors. |
| 80 | PVC Door Shutter-30 mm thick: Supplying fitting and fixing P.V.C. door shutter of approved quality & shade in position, the style & rail of the P.V.C. door shutter will be made of rigid P.V.C. multicavity hollow chamber of 59 mm x30 mm section with 2.0 mm (+/-0.2mm) wall thickness. Horizontal & vertical section shall be fixed to each other by self tapping screws and 1 solid polymeric or M.S. galvanised tubular 'L' shaped bracket 100mm x 200mm in each corner of the shutter frame for placing hinges. Polymer based multicavity hollow section of 120 mm x30mm with 2.0 mm (+/- 0.2 mm) wall thickness will be fitted in the middle, reinforced by solid polymer bar of 200 mm long at both ends and screws from both sides as lock rail. The section frame will then be fitted in by PVC panels of size 100 mmx25 mm with wall thickness of 1.2 mm (+/- 0.2 mm) and 2 nos. of 6 mm dia bright rod will be inserted horizontally with both side check and nut system and stretches where fixing of hinges / hasp bolt / tower bolt /door ring are required to be strong enough to with stand wear and tear. The rate is inclusive of cost of all materials, labour,and hire of tools and plants and appliances. Carriage of all materials taxes and all other incidental charges complete. (Brand Name-(Sintex/Duroplast) |
| 81 | In ground floor. |
| 82 | Supplying, fitting and fixing boiling water proof plyconforming to IS:710-1977 bonded with phenol formaldehyde synthetic resin ocnforming to IS:848-1974 of approved make and brand fitted and fixed as per design ap per approval and direction of Engineer-in Charge. [excluding the cost of supporting frame work and teak wood batten/Lapping] 19 mm Thick |
| 83 | In Ground Floor |
| 84 | Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame exluding cost of concrete, Iron Butt Hinges and M.S clamps. (The quantum should be correted upto three decimals). |
| 85 | (e) Sal : Malayasian |
| 86 | Iron butt hinges of approved quality fitted and fixed with steel screws, with ISI mark.100mm. X 50mm. X 1.25mm. |
| 87 | Anodized aluminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 230/72) fitted and fixed complete. With continuous plate base(Hexagonal/Round rod).150mm grip x 10mm dia rod. |
| 88 | Anodized aluminium barrel / tower / socket bolt (full covered) of approved manufactured from extruded section conforming to I.S. 204/74 fitted and fixed with cadmium plated screws.300mm long x 10mm dia bolt. |
| 89 | Anodized aluminium Aldrop / Sliding bolts of approved quality manufactured from extruded section conforming to I.S specification (I.S: 2681/66) fitted and fixed complete.300mmx16 dia bolt. |
| 90 | Removing old scales, blisters etc. of interior surface of walls, ceiling by scraping etc. and preparing smooth and even surface with rendering or cement mortar (1:2) (as necessary), to make the surface suitable for receiving distemper. |
| 91 | Applying Interior grade Acrylic Primer of approved quality and brand on plastered or cencrete surface old or new surface to receive Distemper/ Acrylic emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification andas per direction of the EIC. One CoatWater based interior grade Acrylic Primer |
| 92 | Applying Acrylic Emulsion Paint of approved make and brand on walls and ceiling including sand papering in intermediate coats including putty (to be done under specific instruction of Superintending Engineer) : (Two coats) Luxury Quality |
| 93 | Applying Exterior grade Acrylic primer of approved quality and brand on plastered or concrete surface old or new surface to receive decorative textured(matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface thoroughly , complete as per manufacturer's specification and as per direction of the EIC. One coat. |
| 94 | In ground floor. |
| 95 | Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturer's specification and as per direction of EIC to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer.Two coat.Super Protective 100% Acrylic Emulsion. |
| 96 | In ground floor. |
| 97 | Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. |
| 98 | Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary : |
| 99 | On timber or other plastered surface, With super gloss(hi-gloss), two coats (with any shade except white) |
| 100 | On steel or other metal surface, With super gloss (hi-gloss), Two coats (with any shade except white) |
| 101 | Supplying best Indian figured glass viz. hammered, fluted, ribbed, pinhead etc. type including cutting to required sizes, setting on putty bases and fitted and fixed with nails and putty complete.(In all floors for internal wall &upto 6 m height for external wall).3 mm thick (White) |
| 102 | Supplying, fitting & fixing UPVC pipes A- Type and fittings conforming to IS:13592-1992 with all necessary clamps nails, including making holes in walls, floor etc. cutting trenches in any soil through masonry concretestructures etc if necessary and mending good damages including joining with jointing materails (Spun Yarn, Valamoid/Bitumen/M-Seal etc) complete. |
| 103 | UPVC Pipes:110 mm. Dia. |
| 104 | Plain Tee: 110 mm. Dia. |
| 105 | Bend 87.5 degree: 110 mm dia |
| 106 | shoe: 110 mm dia |
| 107 | Supplying, fitting and fixing brass ferrule including connection with P.V.C. pipe of approved make upto 450 mm long with plumbing joint,brass over C.P. coupling at both ends, with cap and lining complete in all respect, including cutting trenches in all sorts of soil and filling up trenches as per direction of the Engineer-in-charge. |
| 108 | (i) 25 mm dia. |
| 109 | Supplying, fitting and fixing PVC pipes of approved make of Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads,fitting, fixing etc.complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. Payment for painting will be made seperately)(a) For Exposed WorkPVC Pipes |
| 110 | 15 mm |
| 111 | 20 mm |
| 112 | 25 mm |
| 113 | 32 mm |
| 114 | 40 mm |
| 115 | Supplying, fitting and fixing Peet's valve full way gunmetal standard pattern best quality of approved brand bearing I.S.I. marking with fittings (tested to 21 kg per sq. cm.) |
| 116 | 20 mm dia |
| 117 | 25 mm dia |
| 118 | 32 mm dia |
| 119 | 40 mm dia |
| 120 | Supply, fitting and fixing bib cock or stop cock. |
| 121 | Chromium plated Bib Cock short body (Equivalent to Code No. 511 & Model – Tropical/ Sumthing Special of ESSCO or similar brand. |
| 122 | Chromium plated Stop Cock with wall flange (Equivalent to Code No. 513(A) &513(B) & Model – Tropical/ Sumthing Special of ESSCO or similar brand. |
| 123 | Chromium plated Angular Stop Cock with wall flange (Equivalent to Code No. 5053 & Model - Florentine of Jaquar or similar brand). |
| 124 | Supplying, fitting and fixing shower of approved brand and make. Chromium plated round shower with revolving joint (Equivalent to Code No. 541(N) & Model - Tropical / Sumthing Special of ESSCO or similar brand). |
| 125 | Supplying, fitting & fixing 10 litre PVC lowdown cistern conforming to IS: specification with PVC fittings complete CI brackets including two coats of painting to brackets etc. (Brand:-Reliance classic/Hindware/Parryware) |
| 126 | Supplying, fitting and fixing white vitreous china best quality approved make wash basin with C.I. brackets on 75 mm X 75 mm wooden blocks, C.P. waste fittings of 32 mm dia., one approved quality brass C.P. pillar cock of 15 mm dia., C.P. chain with rubber plug of 30 mm dia., approved quality P.V.C. waste pipe with C.P. nut 32 mm dia., 900 mm long approved quality P.V.C. connection pipe with heavy brass C.P. nut including mending good all damages and painting the brackets with two coats of approved paint. |
| 127 | 450 mm X 300 mm size |
| 128 | 550 mm X 400 mm size |
| 129 | Supplying, fitting and fixing stainless steel sink complete with waste fittings and two coats of painting of C.I. brackets.(a) Sink only 530 mm X 430 mm x 180 mm |
| 130 | Supplying,fitting and fixing approved brand P.V.C. CONNECTOR white flexible, with both ends coupling with heavy brass C.P. nut, 15 mm dia.600 mm long. |
| 131 | Supplying,fitting, fixing approved brand 32 mm dia PVC waste pipe with PVC coupling at one end fitted with necessary clamps.900 mm long. |
| 132 | Supplying, fitting and fixing Waste fittings complete.C.P. over brass32 mm |
| 133 | Supplying, fitting and fixing pillar cock of approved make.CP Pillar Cock - 15 mm. (Equivalent to Code No. 507 & Model -Tropical / Sumthing Special of ESSCO or similar brand). |
| 134 | Supplying, fitting & fixing Aluminium domical grating.125 mm |
| 135 | Supplying, fitting and fixing Anglo-Indian W.C. in white glazed vitreous china ware of approved make complete in position with necessary bolts, nuts etc.(a) With 'P' trap (with vent) each |
| 136 | Supplying, fitting and fixing Closet seat of approved make with lid and C.P. hinges, rubber buffer and brass screws complete.(b) Anglo Indian(i) Plastic (hallow type) white |
| 137 | Supplying, fitting & fixing 32 mm dia. flush pipe including west fitting of approved make and necessary fixing materials, clamps etc. complete.Polythene Flush Pipe. |
| 138 | Supplying, fitting and fixing beveled edged mirror 5.5 mm thick silver red as per I.S. 3438 / 1965 together with brass C.P. hinges.600 mm X 450 mm |
| 139 | Supplying, fitting and fixing towel rail with two brackets.Aluminium25 mm dia. and 600 mm long. |
| 140 | Supplying, fitting and fixing soap holder.Fibre glass |
| 141 | Supplying, fitting and fixing PTMT Smart Shelf of approved make of size300 mm. |
| 142 | Dismantling Orissa pattern WC & E.P.W.C including taking out of base concrete, if necessary, complete. |
| 143 | Cleaning silt of inspection pit |
| 144 | Removing sludge from septic tank, soak well etc. by mathor labour including disposal of the same outside the compound as directed. Upto 20 Users Within a limit of 150 metre. |
| 145 | Cleaning soak pit by removing the top slab and replacing inner filling with jhama bats & repairing the pit as necessary including fitting the slab. |
| 146 | Supply of UPVC pipes (B Type) & fittings conforming to IS-13592-199Single Socketed 3 Meter Length110 mm dia |
| 147 | Supply of UPVC fittings (B Type) & fittings conforming to IS-13592-1992 |
| 148 | Plain Tee :110 mm dia |
| 149 | Bend 45º :110 mm dia |
| 150 | Bend 87.5º :110 mm dia |
| 151 | Door Bend (T.S.) :110 mm dia |
| 152 | Cross Tee :110 mm dia |
| 153 | Vent Cowl :110 mm dia |
| 154 | Pipe Clip :110 mm dia |
| 155 | 110 X 110 P Trap: 75 mm |
| 156 | Supplying P.V.C. water storage tank of approved quality with closed top with lid (Black) - Multilayer |
| 157 | 500 litre capacity |
| 158 | Labour for hoisting plastic water storage tank. |
| 159 | Upto 1500 litre capacity. |
| 160 | Upto 1st story from G.L. |
| 161 | Labour for punching hole in plastic water storage tank upto 50 mm dia. |
| 162 | Construction of septic tank of different capacities as per approved drawing with 1st class brick work in cement mortar (1:4) including two 560 mm dia. R.C.C. manhole cover(heavy type)of approved make supplied, fitted and fixed in the 100mm thick R.C.C (1:1.5:3) top slab with necessary fittings, 20mm thick cement plaster (4 : 1) with neat cement finish to the internal surfaces and 15 mm thick cement plaster (4 : 1) to outside wall upto 200 mm below G.L floor finished with 25 mm thick grey artificial stone over 100 mm thick R.C.C(1:1.5:3) bottom slab including supplying, fitting and fixing all necessry specials, fittings, S.W. tees, C.I. foot rest etc. including excavation earth in all sorts of soil, shoring, bailing out and pumping out water as necessary,ramming, dressing the bed and fefilling the sides of the tanks with earth, removing spoils, filling up the chamber with clear water, removing foreign materials from the chamber and including constructing attached inspection pit as per approved drawingand connecting all necessary pipes, joints etc. with internal plaster work and artificial stone flooring is to be done with admixture of water proofing compound @ 0.5% by weight of cement with all costs of labour and materials. Note:- (i) Finished level of Septic Tank should be 400 mm. from Ground Level. (ii) Height of 50 mm. Ventilation pipe &Mosquito proof mesh, should be follwed as per S:2470,Part- I.Payment will be made separetly on the basis of actual height based on relevant I.S.Code.(i) For 10 users |
| 163 | A) With Pakur variety. (SAIL/TATA/RINL) |
| 164 | Construction of circular soak well 2.5 metre deep in all types of sandy soils with dry brick work upto 1.6 metre from the bottom having 150 mm intermediate cement brickwork (1:4) band all round and cement brick work (1:4) upto 0.90 metre from top with 20mm thick cement plastering (1:4) to inside face upto the depth of cement brickwork, 15mm thick cement plaster (1:4) on outer face from top of the well upto G.L. and 6 mm thick cement plaster (1:4) on top of the R.C.C. cover slab including fillingbottom 1.00 metre of inside of the well with brick metal (50 mm to 63 mm size) including R.C.C. cover slab of 100 mm thick with cement conc (1:1.5:3) with stone chips with necessary reinforcement and shuttering including one 560 mm dia. R.C.C. manhole cover (heavy type)of approved make supplied, fitted and fixed in the coverslab with necessary fittings, making nacessary arrangements for pipe connections, excavation of well including shoring, dewatering and removing the exess earth from the premises as per direction complete in all respect with all costs of labour and materials. With 250 mm thick dry brick work and 250 mm thick cement brick work (1:6) and |
| 165 | 1.00m inside dia.(SAIL/TATA/RINL) |
| 166 | Supplying and fixing double-door SPN MCB Distribution Board with IP-42/43 protection, mounted on wall surface & mending good the damages to original finish incl. Inter connection with suitable size of copper wire and neutral link & provision for earthing attachment. 2+16 way, Make: Legrand/ Crabtree/ Siemens/ ABB/ Schneider/ Havells/ L&T |
| 167 | Supplying and fixing 240/415 V MCB of Breaking capacity 10kA & C characteristics on din rail of existing DBs and necessary connection, DP, 63A, Make: Legrand/ Crabtree/ Siemens/ ABB/ Schneider/ Havells |
| 168 | Supplying and fixing 240/415 V MCB of Breaking capacity 10kA & C characteristics on din rail of existing DBs and necessary connection, DP, 32A, Make: Legrand/ Crabtree/ Siemens/ ABB/ Schneider/ Havells |
| 169 | Supplying and fixing 240/415 V MCB of Breaking capacity 10kA & C characteristics on din rail of existing DBs and necessary connection, SP, 32A, Make: Legrand/ Crabtree/ Siemens/ ABB/ Schneider/ Havells |
| 170 | Supply & Fixing of reputed make PVC/ ABS Junction Box of size 100mm x 100mm x 70mm with DIN Rail and 4-connector. |
| 171 | Supply & Fixing of reputed make PVC/ ABS Junction Box of size 150mm x 100mm x 70mm with DIN Rail and 8-connector. |
| 172 | Supply & Fixing of reputed make PVC/ ABS Junction Box of size 200mm x 100mm x 70mm with DIN Rail and 16-connector. |
| 173 | Supply & Fixing of PVC Casing-Capping (Make- Precision/ Presto Plast, Size-25 × 12mm) along with all accessories complete |
| 174 | Supply & Fixing of PVC Casing-Capping (Make- Precision/ Presto Plast, Size-20 × 12mm) along with all accessories complete |
| 175 | Supply & Wiring with 1.1 KV grade single core PVC insulated stranded Copper wire (Make: Anchor/ Finolex/ Apar/ Havells/ Polycab/ RR Kabel/ KEI/ Goldmedal) in existing PVC Casing-Capping (Make- Precision/ Presto Plast) along with all accessories complete |
| 176 | 6 sq. mm. wire for Main Run from Energy Meter to LTDB |
| 177 | 4 sq. mm. wire for Main Run from LTDB to Switch Boards and Junction Boxes |
| 178 | 2.5 sq. mm. wire for 16 A Switch Socket Board |
| 179 | 1.5 sq. mm. wire for Fan, LED Batten Light, LED Bulbs, Exhaust Fan Point |
| 180 | 1 sq. mm. wire for Earth wiring complete |
| 181 | Supplying & Fixing PVC Modular Switch Board (Make: Presto Plast/ Anchor/ Pritam) of the following sizes complete mounted on wall surface incl. making earthing attachment and mending good damages to building works |
| 182 | 2-Module |
| 183 | 4-Module. |
| 184 | 6-Module. |
| 185 | 2 row 12-Module. |
| 186 | Supply and fixing of following materials on existing wall mounted PVC Modular type switch board and making necessary connections as required. |
| 187 | 240 V 6 A Modular type switch. (Havells/ Legrand/ Crabtree/ Anchor/ Goldmedal) |
| 188 | 240 V 16 A Modular type switch.(Havells/ Legrand/ Crabtree/ Anchor/ Goldmedal) |
| 189 | 240 V, 6A, 5 pin Modular type plug socket. (Havells/ Legrand/ Crabtree/ Anchor/ Goldmedal) |
| 190 | 240 V, 16A, 3 pin Modular type plug socket. (Havells/ Legrand/ Crabtree/ Anchor/ Goldmedal) |
| 191 | 240 V, Modular Type Fan regulator, Make:- Havells/Orient/Bajaj/Crompton/ Goldmedal |
| 192 | 240 V 6 A Modular type bell push switch. (Havells/ Legrand/ Crabtree/ Anchor/ Goldmedal) |
| 193 | Ceiling Rose. |
| 194 | Supply, Deliver and Fixing of 20 Watt, 4 feet LED Batten Light |
| 195 | Supply and Delivery of 20 Watt, 230 V AC, 50 Hz., 4 feet LED Batten Light, Make: Philips/ Havells/ Crompton/ Orient/ Eveready |
| 196 | Fixing only of 4 feet LED Batten Light & fitting complete with all accessories directly on wall/ceiling using wooden round block and suitable size of MS fastener |
| 197 | Supply, delivery and fixing of Ceiling fan complete with all accessories. Rating :- 1200 mm Make:- Havells/Orient/Bajaj/Crompton/ Usha, 230 V AC, >=50 Watt, >=350 RPM and making necessary connection as required by 2x1.5 sqmm flexible copper wire. |
| 198 | Supply, Delivery and fixing of 9 Watt, 230 V AC, 50 Hz., Pin Type LED Bulb, Make: Philips/ Havells/ Crompton/ Orient/ Eveready along with appropriate bulb holder & other accessories and making necessary connection as required by 2x1.5 sqmm flexible copper wire. |
| 199 | Supplying & Fixing 240 V AC/DC superior type Ding-Dong Call Bell (Anchor/ Goldmedal/ Havells/ Crompton) with PVC box and accessories complete on wall |
| 200 | Soil Exacavation for Earthing |
| 201 | For morrum soil |
| 202 | Earthing with 50 mm dia GI pipe 3.64 mm thick x 3.04 Mts. long and 1 x 4 SWG GI (Hot Dip) wire (4 Mts. long), 13 mm dia x 80 mm long GI bolts, double nuts, double washers incl. S & F 15 mm dia GI pipe protection (1 Mts. long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 Mts. below the ground level as below: |
| 203 | By ISI-Medium GI pipe |
| 204 | Supplying & fixing earth busbar of galvanized (Hot Dip) MS flat 25 mm x 6 mm on wall having clearance of 6 mm from wall including providing drilled holes on the busbar complete with GI bolts, nuts, washers, spacing insulators etc. as required |
| 205 | BOC Welfare Cess @1% of the above Please Enable Macros to View BoQ information |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail