|
| 1 | Dismantling of plain or corrugated steel sheeting, any gauge, thickness including Nainital or similar pattern roof covering complete all as directed. |
| 2 | Dismantling of asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as directed. |
| 3 | Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified. |
| 4 | Dismantling boarding, any description, fixed in any position with nails complete all as directed. |
| 5 | Dismantling timber scantlings 40 sqcm and over in section for unframed work, in any position all as directed. |
| 6 | Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets all as directed. |
| 7 | Demolition of Brickwork or stone/ boulder masonry, including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles built in cement mortar complete all as directed by Engineer-in-Charge. |
| 8 | Supply and fix steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161- 1979 grade St.-240 complete all as specified. |
| 9 | Supply and fix pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed. |
| 10 | Supply and fix pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed. |
| 11 | Material and labour for preparation of new and previously untreated steel or iron surfaces of any description, not otherwise described exceeding 10 cm width or girth and applying two coats of synthetic enamel paints over one coat of red oxide primer all as specified. |
| 12 | Material and labour for preparing surfaces of timber piles and diping in a hot mixture of tar and creosote in the proportion of 20 kg coal tar pitch to 25 litres of creosote oil, for 4 mins. complete all as specified. |
| 13 | Material and labour for precast cement concrete block 1:3:6 type C1 using 20 mm graded crushed stone aggregates masonry with solid blocks, exceeding 10 cm in width and setting in cement mortar 1:6, complete all as specified. |
| 14 | Material and labour for 15 mm thick rendering on fair faces of brick or concrete surfaces in cement mortar 1:6 finshed even and smooth without using extra cement complete all as specified. |
| 15 | Material and labour for 20 mm thick rendering in cement mortar 1:4 in two layers (12 mm +8 mm) on external faces of brick wall or concrete surfaces, finished the surfaces even and smooth without using extra cement with using approved Liquid Water Proofing Compound on second layer (8 mm) as per manufacturer instruction complete all as specified and as directed by Engineer-In-Charge. Note: Liquid Water Proofing Compound shall be measured and paid including this item |
| 16 | Material and labour for applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50gm/litre and UV resistance as per IS-15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @1.43 litre/10 Sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 Sqm over new wall surfaces. |
| 17 | Material and labour for preparation of newly plastered surfaces of wall and applying distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre of approved manufacturer of required shade and colour complete, as per manufacturer's specification. Two or more coats over a coat of wall care putty complete all as directed. |
| 18 | Material and labour for for suspended false ceiling using grid 180 GSM (exposed ceiling suspension system ) of grid size 605 mm x 605 mm with main runner 38 mm x 24 mm and wall angle 24 mm x 24 mm using 6 mm thick High Pressure steel Non Asbestos Fibre Cement decorative Board in a grid of powder coated GI system duly suspended with 4 mm dia GI bar hanger fixed with steel dash fasteners or iron purlin from the roof with adjustment clip providing positions for light fixtures, air conditioning diffuser and ducts ,sprinkler ,smoke detectors etc. The main runners to be secured to structural soffits by hanger @ 1210 mm maximum c/c. the last hanger at the end of each main runner should not be placed at more than 450 mm from the adjacent wall, Flush fitting 1210 mm cross tee to be interlocked between main runners @ 605 mm c/c,so as to form 600 mm x 600 mm grid complete all as specified . |
| 19 | Material and labour for second class hardwood boarding for eaves board, clean sawn with butt joints fixed with nails in any position or situation (except flooring and skirting), 20mm thick complete all as specified. |
| 20 | Material and labour for prepration new or previously untreated wood or wood base materials of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified. |
| 21 | Taking down chowkhats with shutters (without taking off shutters from the frames) & removing from site area exc 1.5 Sqm & n. exc 4.00 sqm each complete all as directed. |
| 22 | Taking down chowkhats with shutters (without taking off shutters from the frames) & removing from site area n.exc 1.5 Sqm each complete all as directed. |
| 23 | Supply and fix powder coated anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified |
| 24 | Supply and fix Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge. |
| 25 | Supply and fix anodised aluminium door shutters with powder coating of any colour (Thickness or powder coating not less than 50 micron), aluminium section weighing not less than 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, 4 lever mortice lock, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified |
| 26 | Supply and fix 4 mm thick sheet glass, ordinary quality and glazing in square exceeding 0.50 sqm in each pane in aluminium joinery in each pane complete all as specified. |
| 27 | Supply and fix 5 mm thick sheet glass, ordinary quality and glazing in square exceeding 0.50 sqm in each pane in aluminium joinery in each pane complete all as specified. |
| 28 | Supply and fix Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing conforming to Fe-410W Grade E-250 (quality A) complete all as specified. |
| 29 | Material and labour for 7 mm thick premium quality glazed ceramic colour tiles of size 450 mm x 350 mm/ 350 mm x 250 mm as in skirting / dado / vertical surfaces set and jointed and pointed in white or colour cement to match existing surfaces including 10 mm thick rendering in cement mortar 1:3 complete all as specified. |
| 30 | Supply and fix one piece Vitreous China wash down water closet pan floor mounted, white including fixing bolts, 10 ltr capacity flushing cistern,flush pipe plastic water closet seat white including jet spray, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging devices and also including 'P' or 'S' trap complete all as per manufacturer instruction.Make of Pan Parryware Verve AM / Cera CAMPBELL/ Johnshon COSMO |
| 31 | Supply and fix CP health faucet with tube and wall hook including all fittings as per manufacturer instruction.Make: Parryware Cat No T9961A1/ Jaquar Cat No ALD-579 / Johnson Cat No S0826C |
| 32 | Supply and fix for 15 mm dia cast copper alloy chromium plated two way Bib cock with wall flange concealed type screwed down for iron pipe or for unions complete all as Per manufacturer instruction.Make :- Parryware Cat No G2381A1/ Cera Cat No F1016163/ Johnson Cat No T3370C |
| 33 | Supply and fix, brass CP single lever basin mixer for mixing hot and cold water including 15 mm bore hot water pipe duly insulated with glass wool and aluminium cladding complete all as specified.Make:- Parryware Cat No G3165A1/ Jaquar Cat No COP-001BPM / Johnshon Cat No T6045C |
| 34 | Supply and fix 15 mm dia cast copper alloy chromium plated Angle valves, with wall flange concealed type screwed down for iron pipe of for unions complete all as specified and directed. Make :- Parryware Cat No T3907A1/ Cera Cat No F1016201/ Johnson Cat No T5310C |
| 35 | Supply and fix CP brass connection with CP brass nuts on both ends of length 450 mm,complete all as specified.Make:-Blue Star & Silver Shine/ Prayag Polymer Pvt. Ltd./ Polytuff |
| 36 | Supply and fix second class hardwood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified. |
| 37 | Material and labour for second class hardwood scantling wrought sawn complete all as specified. |
| 38 | Material and labour for solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing. |
| 39 | Material and labour for 5 mm thick PVC sheet fillet of width 35 mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing. |
| 40 | Supply and fix 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified. |
| 41 | Supply and fix as in repairs 12 mm thick prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified. |
| 42 | Supply and fix 125 mm long medium weight, cold rolled mild steel, Butt hinges, complete all as specified. |
| 43 | Supply and fix 100 mm long medium weight, cold rolled mild steel, Butt hinges, complete all as specified. |
| 44 | Supply and fix 200 mm long brass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed complete all as specified |
| 45 | Supply and fix 150 mm long brass handles, cast type, all as specified. |
| 46 | Supply and fix 200 mm long brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts and fixed complete all as specified. |
| 47 | Supply and fix 100 mm long brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts and fixed complete all as specified. |
| 48 | Supply and fix 4 lever aluminium Mortice lock, vertical type, size 75 mm (set of 2 keys) complete all as specified. |
| 49 | Material and labour for 18-20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including 20 mm thick screed bed in cement mortar 1:4, including edge moulding of counters vanities etc. and machine polishing to edge to give high gloss finish etc. complete all as specified. |
| 50 | Supply and fix vitreous china wash basin counter top oval type of size 545x400x185mm including 32mm dia waste fitting including brackets and 32mm dia waste fitting with PVC drainage waste pipe required length upto floor trap complete all as specified. Please Enable Macros to View BoQ information |
| 51 | Supply and fix vitreous china wash basin counter top oval type of size 545x400x185mm including 32mm dia waste fitting including brackets and 32mm dia waste fitting with PVC drainage waste pipe required length upto floor trap complete all as specified. Please Enable Macros to View BoQ information |
