|
| 1 | Dismantling Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and directed. |
| 2 | Dismantling timber scantlings 40 sqm. cm and over in section, in any position for unframed works complete all as specified and directed. |
| 3 | Demolition of roofs, floors (other than ground floors), beams, staircase, landing, chajjas and similar suspended works etc complete all as specified and directed. |
| 4 | M & L for Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof or wall covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 5 | M & L for Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof or wall covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 6 | S & F steel tubular trusses including special shaped washer framed work such as in doors or gate of angle or other section with gusset plates, braces etc. with ends of bars shouldered and/ or riveted, or forged into spikes, framed guard bars , barred iron doo etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St-240 complete all as specified and directed. |
| 7 | M & L for painting to new or previously untreated steel surfaces of any description over 10cm in width or girth with two coats of synthetic enamel paint over a coat of zinc chromic primer including preparation of surfaces complete all as specified and directed. |
| 8 | M & L for false ceiling made out of E-board classic of size 600 x 600 x 4 mm thick, GI frame consisting of main Tee of size 38.50 x 24.00 mm and cross Tee of size 28.50 x 24.00 mm thick made out of PGI sheet 0.30 mm thick doubled at web and single at flange, flange covered with powder coated sheet 0.25 mm thick and angle 24.00 x 24.00 x0.4 mm thick powder coated suspended with GI wire 3 mm dia and up to 2 Mtrs long complete including plugging fixing of angle to brick walls with steel rawl plugs @ 450 mm c/c and applying two coats of Oil Bound distemper to the ceiling board complete all as specified and directed. |
| 9 | Demolition of cement concrete (un-reinforced) in ground floor and paving not exc 15 cm thickness (below or above ground level) & removing unserviceable materials in low laying area, complete all as specified and directed. |
| 10 | M & L for 25 thick cement concrete (1:2:4), type B-1 (using 20mm graded crushed stone aggregate) as in levelling coarse for tiles complete all as specified and directed. |
| 11 | M & L for vitrified ceramic tiles (light shade) 10mm thick (square/rectangular), polished, coloured (light shade as approved), area of each tile not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar (1:6) complete all as specified and directed. |
| 12 | M & L coloured non skid ceramic tiles 7 to 8mm thick (square /rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar (1:6) complete all as specified and directed. |
| 13 | M & L for vitrified ceramic tiles 10mm thick (square/rectangular), polished, coloured (light shade as approved), area of each tile not exceeding 0.36 sqm, on vertical surfaces such as dado, skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick screed bed in cement & sand mortar (1:4) complete all as specified and directed. |
| 14 | M & L Glazed ceramic coloured tiles in vertical surface 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of the tiles and over 10 mm thick rendering in cement mortar (1:4) complete all as specified and directed. |
| 15 | Demolition of brick/stone masonry built in cement/lime mortar of any mix including all quoins pillar ashlars masonry and removal complete all as specified and directed. |
| 16 | M & L brick work old size sub class 'B' bricks straight or curved on plan to any radius in half brick thick wall built in cement mortar (1:4) complete all as specified and directed. |
| 17 | M & L brick work sub class 'B' bricks (OLD SIZE BRICKS) straight or curved on plan exc 6 mtr mean radius built in cement mortar (1:6) complete all as specified and directed. |
| 18 | Taking down cement plaster or cement lime plaster on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc complete all as specified and directed. |
| 19 | M & L rendering 15mm thick in cement mortar (1:4) on fair faces of brick masonry or concrete surfaces of walls, finished even & smooth without using extra cement complete all as specified and directed. |
| 20 | M & L for applying Two coats of 100% Premium acrylic exterior emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and directed. |
| 21 | M & L rendering 10mm thick in cement mortar (1:6) on fair faces of brick work or concrete surfaces, finished even & smooth without using extra cement complete all as specified and directed. |
| 22 | M & L for preparation of new plastered or unplastered surfaces of walls and distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour over 1mm thick wall care putty complete as per manufacturer's specification complete all as specified and directed. |
| 23 | M & L for 75 mm thick PCC (1:3:6) type C-2 (using 40 mm graded stone aggregate) as in plinth protection surface finished fair and even complete all as specified and directed.Note:- Plinth protection shall be laid to slope (1 in 30) in bays not exceeding 3 metre in length and joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with sealing compound grade B. |
| 24 | M & L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills,cooking platforms and like over 10 mm thcik cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 15mm thick screed bed cement mortar (1:6) complete all as specified and directed. |
| 25 | Taking down chowkhat or frame (without taking off shutter from the frame) not exceeding 1.5 Square Metre each , removing from the site including cutting holes required for taking out existing hold fast etc. complete all as specified and directed. |
| 26 | Taking down chowkhat or frame (without taking off shutter from the frame) exceeding 1.5 Square Metre and not exceeding 04 Square Metre each, removing from the site including cutting holes required for taking out existing hold fast etc. complete all as specified and directed. |
| 27 | S & F pressed steel frames of size 125 x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed. |
| 28 | S & F 40mm thick flush shutters, solid core construction with block board core and plywood face panels, commercial type on both sids complete all as specified and directed. |
| 29 | S & F 35mm thick second class, hard wood(hollock), glazed and skeleton shutter, open rebated and prepared to receive glass/guage etc, without sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a) supplied and fitted to chowkats complete all as sepcified and directed. |
| 30 | S & F colled rolled mild steel butt hinges 100 mm long medium weight to pressed steel/angle iron frames by welding/ screws complete all as specified and directed. |
| 31 | S & F 200mm size aluminium anodised barrel tower bolt extruded section, ISI marked & fixed complete all as specified and directed. |
| 32 | S & F 150mm size extruded aluminium alloy handles fabricated type anodised ISI marked complete all as specified and directed. |
| 33 | S & F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed. |
| 34 | S & F door closer hydraulically regulated, designation No. 2, aluminium (Die cast) body, universal type (ISI marked) suitable for door shutters of 701 to 850mm in width aand weight between 36 to 60 Kg and fixed complete all as specified and directed. |
| 35 | M & L for preparation of new or previously untreated wood and wood based material/surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 36 | S & F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples & screwed complete all as specified and directed. |
| 37 | S & F anodized aluminium frame with power coating (minimum thickness 50 micron) and other sections for doors, windows, ventilators, partitions, with one or more rebates including joining cleat for fixing etc. complete all as specified and directed. |
| 38 | S & F anodized aluminium window and ventilator shutters side hung type/sliding type without sash bars, aluminium section weighing not less than 0.55 kg/m with power coating (minimum thickness 50 micron) including necessary joining cleats, glazing clips, rubber packing,anodized aluminum snap beading screws anodized aluminium fittings such as peg stays 150mm long (01 No.) hinges type B-21 100mm long (02 Nos.) suitable handle (01 No.) complete all as specified and directed. |
| 39 | S & F in repair of venation blinds (super quality) to window openings complete all as specified and directed. |
| 40 | S & F Mild stee TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 41 | M & L for RCC (nominal mix) (1:2:4) type B-1 (using 20 mm graded stone aggregate) as in Beams, cantilevers, bressummers,lintels over 1.5m span complete all as specified and directed. |
| 42 | M & L formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressumers, lintels, cantilevers, shelves including supports, overhangs etc complete in flat fair finished surfaces of concrete complete all as specified and directed. |
| 43 | S & F for solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed. |
| 44 | S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed. |
| 45 | S & F 125mm Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed. |
| 46 | S & F 100 mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed. |
| 47 | S & F 125 mm long Extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed. |
| 48 | Taking up or down 15mm steel tubing and connections, including cleaning for re-fixing or removal to store |
| 49 | Taking up or down 20mm steel tubing and connections, including cleaning for re-fixing or removal to store |
| 50 | S & F steel tubing medium grade 15mm bore with all fittings fixed complete to wall and or laid in floor complete all as specified and directed. |
| 51 | S & F steel tubing medium grade 20mm bore with all fittings fixed complete to wall and or laid in floor complete all as specified and directed. |
| 52 | S & F in repair vitreous china wash down water closet pan (Pedestal pattern), white (ISI marked), including connection to drain (or outgoing pipe) and to flushing pipe, anti-syphonoage pipe etc & with plastic WC seat cover (white) closed pattern with flat bottom and cover and suitable mild steel chromium plated or aluminised hinging device complete all as specified and directed. |
| 53 | S & F in repairs Jet spray chromium plated brass for EWC with & including PVC connection 600 mm long suitable for 15 mm bore GI pipe with PTMT nut & nipple complete all as specified and directed. |
| 54 | S & F in repairs PVC low level flushing cistern 10 litrs capacity (white ISI marked) with inlet ball valve, float and handle, syphonic action type including brackets and flush pipe of polythelene of low or high density of PVC 32mm dia complete all as specified and directed. |
| 55 | S & F in repairs PVC connection of 15mm bore with 2 Nos. PTMT nuts, 60cm long fixed with one end to pillar tap & the other end to stop cock or iron pipe complete all as specified and directed. |
| 56 | S & F in repair towel rails of 20mm dia tubular brass chromium plated 60cm long 'D' type fixed complete all as specified and directed. |
| 57 | S & F in repairs MS grating CP 100mm dia, with hole/without for waste pipe of approved make including fixing with CM to floor/nahani traps etc complete all as specified and directed. |
| 58 | S & F in repairs fancy typer Pillar tap, cast copper alloy with capstan heads, chromium plated, screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks & fly nuts, screwed for iron pipes of 15mm bore complete all as specified and directed. |
| 59 | S & F in repairs brass chromium plated shower rose 125mmx125mm size with swivel joint type including fixing to steel pipe of 15mm bore or union complete all as specified and directed. |
| 60 | S & F in repairs looking mirror 600x450mm bevelled edge 5.5mm thick selected quality glass, mounted on 6mm thick commercial ply, aluminium frame around and fixed to wooden plug with CP brass screws and cup washers complete all as specified and directed. |
| 61 | S & F in repair fancy type bib taps, chromium plated alloy with crtuch or butterfly handle,screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. |
| 62 | S & F in repair fancy type angle/stop valves, chromium plated alloy screwed down high presure, screwed both ends for iron pipe or for unions of 15 mm dia long sunk concealed type complete all as specified and directed. |
| 63 | S & F in repairs Brass CP Wall mixer(Non Telephonic Type) with L bend 3-in-1 for mixing hot & cold water screwed down for iron pipe 15 mm bore and fixed complete all as specified and directed. |
| 64 | S & F in repair chromium plated Brass health faucet for EWC with including flexdible pipe minimum 1m long suitable for 15mm bore with all connected fittings complete all as specified and directed. |
| 65 | S & F in repairs 32/40mm dia PVC flexible waste pipe 80cm long with socket for union, for WHB/urinal/sink complete all as specified and directed. |
| 66 | S & F in repairs vitreous china wash basin white, flat back, size 550mm x 400mm including waste coupling brass CP 32mm bore, and 02 Nos CI brackets complete all as specified and directed. |
| 67 | S & F in repair 75mm dia bore PVC (SWR) pipes single socketed, in any length with rubber ring joints or solvent cement, laid in trenches or in floors, 75mm bore including taking down existing pipe with fitting by necessary excavation, return filling and demolition of PCC etc if required complete all as specified and directed. |
| 68 | S & F 75 mm bore PVC (SWR) bends any radius,complete all as specified and directed.Note: The existing fittings are deemed to be taken down along with the SWR pipe. |
| 69 | S & F 110 mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints,fixed to walls including taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks,etc.(measured overall as fixed along the centre line over fittings and accessories), complete all as specified and directed. |
| 70 | S & F 110 mm bore PVC (SWR) bends any radius,complete all as specified and directed.Note: The existing fittings are deemed to be taken down along with the SWR pipe. |
| 71 | S & F 5mm thick frosted glass in squares exc 0.5 sq. m each pane complete all as specified and directed. |
| 72 | S & F 4.8/5mm thick sheet glass ordinary quality and glazing with oil putty in squares not exceeding 0.5 sqm each pane complete all as specified and directed. |
| 73 | M & L for 100mm thick Cement concrete type D- 2, (1:4:8) (using 40mm graded stone aggregate) as in sub base complete all as specified and directed. |
| 74 | M & L for pre-polished cement concrete chequered tiles of size 300mm x 300mm x 25 mm thick, any shape of any tint, heavy duty, set jointed and pointed with grey cement slurry @ 2.5 Kg per square metre over & including 15 mm screed bed in cement mortar (1:6) complete all as specified and as directed. |
| 75 | Taking down carefully copper / aluminium point wiring light / fan, socket or power point complete including fittings such as switches, sockets, ceiling rose, bell push bell buzzer lamp holder bracket etc. removing from site and making good disturbed surface of wall, floor etc complete all as specified and directed. |
| 76 | M & L for concealed point wiring (in replacement, if needed) complete with PVC insulated and unsheathed FRLS cable of 1.5 sqmm (nominal area) with multi stranded copper conductor single core 1100 volts grade in and including rigid PVC conduit ISI marked medium grade not less than 20 mm dia, with MS stove enamelled sunken boxes (normal and modular type as required) including earth dolly with plastic laminated sheet top cover (cover plate with frame in case of modular) of approved make and colour including 1.5 sqmm multi stranded FRLS copper conductor cable of green colour as continuous earth wire with lugs and accesseries and making good disturbed surfaces of walls/floor etc complete all as specified and directed for the followings :-One light / fan point controlled by one way switch |
| 77 | All as per Item No 76.00 here-in-above but for one 5 Amp socket outlet on independent board complete all as specified and directed. |
| 78 | All as per Item No 76.00 here-in-above but for one 5 Amp socket outlet on same board complete all as specified and directed. |
| 79 | All as per Item No 76.00 here-in-above but using 2.5 sqmm single core multi stranded copper conductor PVC insulated and unsheathed, FRLS cable for 15 Amp socket outlet on independent board including 2.5 sqmm multi stranded copper conductor cable of green colour as continuous earth wire with lugs etc as required complete all as specified and directed. |
| 80 | S & F socket outlet 6A-2/3 Pin combined 2 module modular type complete all as specified and directed. |
| 81 | S & F socket outlet 6A/16A-2/3 pin combined 2 module modular type complete all as specified and directed. |
| 82 | S & F switch 6 amps modular type one one way complete all as specified and directed. |
| 83 | S & F switch 16 amps modular type one one way complete all as specified and directed. |
| 84 | S & F in replacement of Lamp holder bakalite type with back plate suitable for batten fittings complete all as specified and directed. |
| 85 | S & F in replacement/new ceiling rose surface bakelite 63 x50mm three terminals complete all as specified and directed. |
| 86 | S & F in replacement of sub main wiring with PVC insulated, FRLS unsheathed two single core cable 1100 volts grade with stranded copper conductor of size 4.0 sqmm (Nominal area) drawn in and including PVC conduit of suitable size as directed with and including one run of 4.0 sqmm multi stranded copper conductor single core PVC insulated, unsheathed cable of green colour as continuous earth wire including lugs etc connected and tested complete all as specified and directed.Note: (i) Two runs of 4.0 sqmm cable and one run of 4.0 sqmm cable of earth continuity conductor and conduit shall be a unit length. Please Enable Macros to View BoQ information |
| 87 | S & F in replacement of sub main wiring with PVC insulated, FRLS unsheathed two single core cable 1100 volts grade with stranded copper conductor of size 4.0 sqmm (Nominal area) drawn in and including PVC conduit of suitable size as directed with and including one run of 4.0 sqmm multi stranded copper conductor single core PVC insulated, unsheathed cable of green colour as continuous earth wire including lugs etc connected and tested complete all as specified and directed.Note: (i) Two runs of 4.0 sqmm cable and one run of 4.0 sqmm cable of earth continuity conductor and conduit shall be a unit length. Please Enable Macros to View BoQ information |
