|
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. -All kinds of soil |
| 2 | Supplying and filling in plinth, under floor, foundations etc. with sand (fine) from local quarry with all lifts including spreading in horizontal layers, watering, grading to required slope, ramming, consolidating and compacting each layer by using plate compactor or by any suitable method complete. |
| 3 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering -All work upto plinth level: -1:3:6 ( 1 Cement: 3 fine sand : 6 graded well burnt brick aggregate 20 mm nominal size) |
| 4 | First class brick work in foundation and plinth including cost of all materials as required complete:-In cement mortar 1:4 ( 1 cement : 4 fine sand ).` |
| 5 | 12 mm cement plaster of mix : In cement mortar 1 : 4 ( 1 cement : 4 fine sand ) |
| 6 | Steel work in built up tubular (round, square orrectangular hollow tubes etc.) trusses etc., includingcutting, hoisting, fixing in position and applying apriming coat of approved steel primer, including weldingand bolted with special shaped washers etc. complete. Hot finished welded type tubes |
| 7 | Supply & installation of pre-painted Galvalume sheetsfor roofing/cladding (size, shape and pitch ofcorrugation as approved by Engineer-in-charge) in550mpa steel grade, made out of Cold Rolled Steelcoated with Zinc-Aluminium alloy coating of 43.5% Zn,55% Al and 1.5% Silicon confirming to ASTMA792/A792M and AS1397, Alloy coating AZ150/AZ70,colour coated with high quality Polyester coating, topcoated of modified polyester of 20 micron, back sidecoat of 5 micron, having epoxy primer coat of 5 micronon both side. Sheet should have protective guard filmof 25 microns minimum to avoid scratches whiletransportation and should be supplied in singlelength upto 12 metre or as desired by Engineer-incharge.The sheet shall be fixed using self drilling/self tapping screws of size (5.5x 55mm) with EPDMwashers filled with white lead complete upto anypitch in horizontal/ vertical or curved surfacesexcluding the cost of purlins, rafters and trusses andincluding cutting to size and shape wherever requiredand as per direction of Engineer-in-charge.0.40mm thickness |
| 8 | Finishing with Epoxy paint ( two or more coats) ofapproved brand and manufacture at all locationsprepared and applied as per manufacturer's specificationincluding appropriate priming coat, preparation ofsurface etc. complete [Payment shall be made aftersubmission of Test Certificate issued by theManufacturer]. On steel work |
| 9 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - -All work upto plinth level:1:2:4 ( 1 Cement: 2 fine sand : 4 graded stone aggregate 20 mm nominal size) |
| 10 | Flat brick soling providing and laying flat brick soling layer on prepared subgrade according to lines. Grade and cross-section show on the drawing, filling joint with Earth free from clay with a plasticity index not exceeding 6 watering and rolling the same ith three wheeled road roller 80-100 kn as per MoRD Technical Specification Clause 412. |
| 11 | Providing and laying brick edging laid lengthwise on prepared sugrade according to lines grades and cross section shown on the from clay with a plasticity Index not exceeding & watering and rolling the same with thre wheeled road roller 80-100 KN as per MoRD Technical Specification Clause 412. Please Enable Macros to View BoQ information |
