|
| 1 | Earth work in excavation by mechanical means (Hydraulic Excavator)/ manual means over areas (exceeding 30 cm in depth, 1.50M in width as well as 10 Sqm on plan) including disposal of excavated earth lead upto 50m and for all lift , as per direction of EIC .All kinds of soil. |
| 2 | Supply & filling in plinth with local river sand under floors including watering, ramming, consolidation and dressing complete. |
| 3 | Engagement of mechanical excavator (tyre mounted) with bucket capacity .30 cum including the cost of fuel,lubricant, driver and helper. |
| 4 | Filling available excavated earth (excluding rock) in trenches, plinth sides of foundation etc. in layers not exceeding 20cm in depth consolidating each deposited layer by ramming and watering lead upto 50m and lift upto 1.50m |
| 5 | Dismantling CC works including disposal of unserviceable materials up to a distance of 50 M lead outside the periphery of area cleared |
| 6 | Dismantling brick work manually / by mechanical means in cement mortar including stacking of serviceable materials and disposal of unserviceable materials upto a distance of 50 m lead as per the direction of EIC. |
| 7 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 m lead |
| 8 | Providing & laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering and reinforcement - all work upto plinth level RCC 1:2:4 (1 cement : 2 river sand : 4 stone aggregate 20 mm nominal size) |
| 9 | Providing and laying in position cement concrete of specified grade CC 1 : 3 : 6 ( 1 Cement : 3 river sand : 6 Stone aggregate 20mm nominal size) excluding the cost of centering & shuttering - All work upto plinth level |
| 10 | Providing and laying in position cement concrete of specified grade CC 1 : 4 : 8 ( 1 Cement : 4 river sand : 8 Stone aggregate 40 mm nominal size) excluding the cost of centering & shuttering - All work upto plinth level |
| 11 | Reinforcement for RCC work including bending, binding and placing in position complete |
| 12 | Labour rate for reinforcement for RCC work including bending, binding and placing in position complete |
| 13 | Centering and shuttering including strutting, propping etc and removal of form work for: (a) Foundation, footings, bases of columns etc. for mass concrete |
| 14 | Pucca brick work in foundation and plinth using common burnt clay local best quality bricks in cement mortar 1: 6 (1 cement : 6 river sand) including curing etc. complete . |
| 15 | Half brick masonary with local best quality bricks in superstructures above plinth level upto floor five level in cement mortar 1: 4 (1 cement : 4 river sand). |
| 16 | 12 mm cement plaster of mix 1 : 6 (1 cement : 6 river sand) at all height . |
| 17 | 15 mm cement plaster of mix (a) 1 : 6 (1 cement : 6 river sand) at all height |
| 18 | Neat cement punning at all height . |
| 19 | Repairs to plaster of thickness 12mm to 20mm in patches of 2.50 sqm & under including cutting the patch in proper shape and preparing and plastering, finishing of walls complete including the surface rubbish to the dumping ground with cement mortar 1:4 as per the direction of EIC |
| 20 | Dismantling of wooden / MS doors, windows and clerestory windows shutters of area 3 Sqm. & below including frames; hold fast etc. complete and stacking of serviceable materials and disposal of unserviceable materials up to Township maintenance store |
| 21 | Dismantling wood work in frames, trusses, purlins and rafters up to 10 M span and 5 M height of sectional area 40 Sq CM & above including stacking the materials at our store |
| 22 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wroughed frame of locally available best quality wood and fixed in position |
| 23 | Labour rate for wood work in frames of doors, windows, celetory windows and other frames wroughed, framed and fixed in position- . |
| 24 | Providing wood work in frames of false ceiling, partitions etc. sawn and put up in position |
| 25 | Providing and fixing 40 x 5 mm flat iron hold fast 40 cm long including fixing to frame with 10mm diameter bolts, nuts and wooden plugs and embedded in cement concrete block 30 x 10 x 15cm with cement concrete of mix 1 : 3 : 6 (1 cement : 3 river sand : 6 |
| 26 | Supplying MS Bolts & Nuts with washer of different diameter as per site requirement |
| 27 | Providing and fixing ISI marked flush door shutters confirming to IS:2202 (Part-1), non decorative type , core or block board construction with frames of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands (ii) 30 mm thick |
| 28 | Repairs to flush doors shutter or cupboard shutter by fixing 3 mm ply to the damaged portion of door with nails at 100 mm C/C & use of approved quality adhesive finished smooth complete in all respect as per the direction of Engineer-In-charge |
| 29 | Providing and fixing approved quality MS pressed butt hinges bright finished with necessary screws etc. complete:(a) 125 x 65 x 2.12 mm |
| 30 | Providing and fixing approved quality MS pressed butt hinges bright finished with necessary screws etc. complete:(b) 100 x 58 x 1.90 mm |
| 31 | Providing and fixing approved quality MS pressed butt hinges bright finished with necessary screws etc. complete:(c) 75 x 47 x 1.70 mm |
| 32 | Providing and fixing approved quality MS bright finished handle with necessary screws etc. complete:(a) 75 mm |
| 33 | Providing and fixing approved quality MS bright finished handle with necessary screws etc. complete:(b) 100 mm |
| 34 | Providing & fixing oxidised approved quality MS tower bolts with necessary screws etc. complete :(a) 100 x 10 mm |
| 35 | Providing & fixing oxidised approved quality MS tower bolts with necessary screws etc. complete :(b) 150 x 10 mm |
| 36 | Providing & fixing approved quality oxidised MS sliding door bolts with nuts & bolts etc. complete:(a) 250 x 16 mm |
| 37 | Providing & fixing approved quality oxidised MS sliding door bolts with nuts & bolts etc. complete:(b) 300 x 16 mm |
| 38 | Repairs to all types of wooden doors by fixing aluminium plain sheet to the damaged portion of door with nails at 100 mm c/c finished smooth complete in all respect as per the direction of Engineer-In-charge. |
| 39 | Renewing approved quality glass panes with putty / wooden fillets and nails where ever necessary (b) 4mm thick @ 10 Kgs/ Sqm |
| 40 | Renewal of old putty of glass panes (Length) |
| 41 | Supplying & fixing new wooden fillets where ever necessary of local best quality wood |
| 42 | Labour rate for minor repairing of wooden doors , windows and ventilators like re-alignment of shutters, refixing of hinges etc. to make it free for operation as per the direction of Engineer-In- Charge (Repalced fittings & timbers shall be paid separately |
| 43 | Providing and fixing 30 mm thick glazed shutters for doors, windows & clerestorty windows of local best quality wood using 4 mm float glass panes including black enamelled ISI marked MS butt hinges with necessary screws |
| 44 | Providing and fixing reputed brand & manufacturer 21mm thick pvc door shutter along with pvc door frame including oxidised MS hinges with necessary MS screws |
| 45 | Dismantling AC Plain or corrugated / transparent sheets in roofing including ridges, hips, valleys and gutters etc. and stacking the material within 50 m lead |
| 46 | Providing reinforced by organic fibres and/or inorganic synthetic fibres cement 6 mm thick corrugated sheets (as per IS: 14871) roofing up to any pitch and fixing with polymer coated J, or L hooks, bolts and nuts 8 mm dia. G.I. plain and bitumen washers or with self drilling fastener and EPDM washers etc. complete (excluding the cost of purlins, rafters and trusses), including cutting sheets to size and shape wherever required. |
| 47 | Providing and fixing ridges and hips in fibre cement reinforced by organic fibres and/or inorganic synthetic fibres roofing with suitable fixing accessories or self drilling fastener and EPDM washer etc.complete.Corrugated serrated adjustable ridges |
| 48 | Providing and fixing 0.63 mm thick with zinc coating corrugated CGI sheets not less then 275 gm per SQM in roofing and site cladding fix with galvanised iron J or I hooks or bolts and nuts 8mm diameter with bitumen and GI limpet washer or GI limpet washers filled with white lead complete excluding the cost of purlins , rafter and trusses . |
| 49 | Labour rate for fixing corrugated AC / CGI / Aluminium / translusent sheets in roofing / ceiling and in side cladding fixed with galvanised iron J or L hooks, bolts & nuts of 8mm dia with GI plain & bitumen washers complete excluding the cost of purlins,(a) Height up to 5.00 M |
| 50 | Providing and fixing asbestos cement 6mm thick corrugated sheets in roofing and side cladding and fixing with GI J or L hooks bolts and nut 8mm dia including GI plain and bitumin washers complete at all height excluding the cost of purlins rafters, trusses and other supporting structures at upto 60 degree pitch, height upto 5m |
| 51 | Steel work in single section fixed with or without connecting plates but including cutting, welding, hoisting, fixing in position all complete in Tee, channels & angles |
| 52 | Labour rate for steel work in single section fixed with or without connecting plates or in tublar section but including cutting, welding, hoisting, fixing in position all complete in Tee, channels & angles |
| 53 | Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts,cutting rivets, welding etc. dismembering and stacking within 50 M lead |
| 54 | Providing & fixing White vitreous china water closet squatting pan(Indian type) along with \\"S\\" or \\"P\\" trap including dismantling of oldWC seat and \\"S\\" or \\"P\\" trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i/c malba, all complete as per the direction of Engineer-in charge. Orissa pattern WC pan |
| 55 | Providing & fixing a pair of white vitreous china 250 x 130 x 30 mm foot rests of standard pattern for squatting pan closet or urinal basin |
| 56 | Providing and fixing white vitreous china pedestal type water closet(European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls andfloors wherever required : |
| 57 | Providing and fixing P.V.C. low level flushing cistern with manuallycontrolled device (handle lever) conforming to IS : 7231, with all fittingsand fixtures complete.17.18.1 10 litre capacity - White |
| 58 | Providing & fixing in position 32 mm diameter PVC (approved quality) telescopic flush pipe complete cutting & making good the walls & floors including making all the connection but excluding the cost of fittings |
| 59 | Providing and fixing aluminium die cast body tubular type universalhydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. |
| 60 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :One urinal basin with 5 litre white P.V.C. automatic flushingcistern |
| 61 | Providing & fixing in position 60 x 45 cm plain mirror superior glass of approved quality complete with 6 mm thick hard board ground fixing to wooden cleats with CP brass screws and washer complete |
| 62 | Labour rate for repairing of high / low level automatic cistern by adjusting floating valves and other internal fittings as per the direction of EIC. |
| 63 | Providing & fixing white vitreous china wash basin along including making all connections but excluding the cost of fittings of following sizes (ii) 450 x 300 mm |
| 64 | Providing and fixing PTMT stop cock of approved quality and colour 15 mm nominal bore, 86 mm long, weighing not less than 88 gms |
| 65 | Providing and fixing PTMT stop cock of approved quality and colour 20 mm nominal bore, 89 mm long, weighing not less than 88 gms |
| 66 | Providing and fixing PTMT pillar cock of approved quality and colour.15 mm nominal bore, 107 mm long, weighing not less than 110 gms |
| 67 | Providing & fixing PVC bib cock of approved quality |
| 68 | Providing & fixing PVC waste of approved quality. |
| 69 | Dismantling GI pipes (External work) including excavation and refilling trenches after taking out the pipes manually / by mechanical means including stackibg of pipes within 50 metres lead as per direction of EIC :(a) From 15 mm to 40mm NB |
| 70 | Providing & fixing GI pipes confirming to IS 1239 (Part-1) / 2004 complete with GI fittings including trenching and refilling etc. (External work):(a) 15 mm nominal bore |
| 71 | Providing & fixing GI pipes confirming to IS 1239 (Part-1) / 2004 complete with GI fittings including trenching and refilling etc. (External work):(b) 20 mm nomonal bore |
| 72 | Providing & fixing GI pipes confirming to IS 1239 (Part-1) / 2004 complete with GI fittings including trenching and refilling etc. (External work):(c) 25 mm nominal bore |
| 73 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (external work) (a) 15 mm nominal bore |
| 74 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (external work) (b) 20 mm nomonal bore |
| 75 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (external work) (c) 25 mm nominal bore |
| 76 | Making connection GI distribution branch with main, by providing & fixing tees, nuts etc. including cutting and threading the pipes, testing etc. complet.(a) 25 mm to 40 mm Nominal Bore |
| 77 | Providing and fixing uplasticised PVC connection pipe with brass unions :45 cm length - 15 mm nominal bore |
| 78 | Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. |
| 79 | White washing with lime on old work (one or more coat) to give an even shade |
| 80 | Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour on old work one or more coats |
| 81 | Applying priming coat with ready mixed red oxide Zinc chromate primer of approved brand & manufacture on steel galvanised iron / steel work |
| 82 | Painting with synthetic enamel paint of approved brand & manufacture in all shades to give an even & smooth shade including cleaning of surface :Old wood / steel works |
| 83 | Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. |
| 84 | Painting with oil type wood preservative of approved brand and manufacture on old work (one or more coats). |
| 85 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 86 | Engagement of manpower for miscellenous civil work as per the direction of Engineer-In-Charge Please Enable Macros to View BoQ information |
