|
| 1 | Excavation in Cutting in Soil by manual means with lead upto 50m Excavation for roadway in soil using manual means for carrying of cut earth to embankment site with a lift upto 1.5m and lead upto 50m as per MoRTH Specification Clause 301.3 |
| 2 | Carriage of Earth sand line Murom with all leads |
| 3 | Providing and laying in position cement concrete including curing, compaction etc complete in specified grade excluding the cost of centering and shuttering- All work up to plinth level. 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size). |
| 4 | Interlocking Concrete Block Pavement with M-30 Grade 0.30 Mtr x 0.30 Mtr x 0.15 Mtr Edge Blocks (measurements shall be made inner to inner side of edge blocks) Providing and Laying of Interlocking M-30 grade Concrete Block Pavements having thickness 80 mm as per drawings and as per IS 15658: 2006.and all materials shall conform to MoRTH Specification Clause 602 with M-30 Grade 0.30 Mtr x 0.30 Mtr x 0.15 Mtr Edge Blocks. Category 'A' : Dentated units to key into each other on all four faces Zigzag shape as per IRC:SP:63-2004 |
| 5 | Repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq. metres and under including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 m lead With cement mortar 1 :4 ( 1 cement : 4 coarse sand) |
| 6 | Plaster on new surface on walls in cement sand mortar1:4 including racking of joints etc. complete fine finish : 20mm thick . |
| 7 | Providing and applying white cement based putty over plastered surface to prepare the surface even and smooth complete New Plastered Surface (three or more coats) |
| 8 | Suppling and laying of prepared & fully developed slection Ist lawn rolls, including cost & tranporation of lawn rolls, preparation of bed also cost of all labours, manur water charges, removing of grass and stone from beds. Maintance of lawn upto three months all work executed as per direction of Engineer incharge. (approved by Chief Eng. Kota) |
| 9 | Finishing walls with Acrylic Smooth exterior paint of required shade including all scaffolding. New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/ 10 sqm ). |
| 10 | Providing and making artstic/heritage painting with the using oil paint /apex ultima or equivalent exterior paint having anti algal and dust pick up resistance with finish as per direction of Engineer in charge on wall faces/ panels etc. with approved colour in following pattern including painting base works of required exterior paint in approved quality / brand : the Painting shall be based on themes related to flora and fauna like creepers flower pots, animals, birds and natural figures. as the work shall be at the level of similar to enclosed drawing. |
| 11 | 150cm high fencing with angle iron 50x50x6mm. placed at every 3Mtr. apart 30cm. in ground embedded in cement concrete 1:3:6 (30x30x45cm) corner and every tenth post to be strutted with 50x50x6mm. angle iron provided with 5 horizontal lines and two diagonals of black barbed wire between two posts fitted and fixed with G.I. staples including earth work in excavation etc. complete. |
| 12 | Providing & Fixing of Pre Cast Coated Concrete bench made of M-20 reinfor cement concrete having Each bench consists of 2 No.s L-Shape base support in white cement color (thickiness:-100 mm, Back height: 1000 mm, Front height :450 mm, Base width: 620mm) and 2 Nos. reinforced concrete planks in yellow & red color of size 1200 mm x 150mm X 50 mm, supreme designds smooth surface finish and durable structure.overall Dimensions: Seating length of the Bench: 1200; Seating heigh of the Bench 450 mm Total height of the Bench 1000 mm |
| 13 | Supply & fixing Equiopment for open jym as per following details. Item should be fix properly including E/W & C.C. in M-20 as per requirement.• LEGG PRESS:- DIMENSIONS: - 1840mm (Length) x 360mm (Width) x 1560mm. (Height).• SAFE AREA:- 2.8 x 1.4Mtr.• Leg Press equipment made from “C” Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters• The center pipe is of 100mm NB made from “C” Class G.I. pipe.• The Sleeve frame is of 100 OD and of M.S. Seamless Pipe with thickness 5mm. This sleeve can be disassembled from main frame.• The bottom support of M.S. round plate of Ø250 mm & 10mm thick.• The remaining outer frame is of 32NB made from “C” class G.I. pipe.• The foundation used for fixing is structure and made from center pipe of G.I. of 80mm. NB “C” class welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angle of 3 mm thickness and 20mm x 40mm CRC. square pipe of 3mm thickness.• Seat & Back rest provided are made up of MS deep draw quantity of 2mm thickness with no joint with uniform outer edge radius 20mm.• The footrests are made from casted Aluminum material, having sizes 130mm X 310mm X 5mm thick. With the support of 310mm X 130mm X 3mm thick MS plate.• The frame of footrests made up of 25 NB “C” class G.I. pipe.• Closing Caps are made up of high quality Fiber reinforced Plastic material.• To build structure bushes are used which are made from M.S. seamless pipe of 50mm O.D. and 5mm thickness.• The pins used are made up of Ø25 mm SAE 8620 bright material.• The bearings used are of “6205zz” permanent lubricated sealed bearing of reputed Brand.• High tensile steel with galvanized nut bolts are used for assembly.• The cerclips used for assembly are of A24 mm.• The powder coating done with Pure Polyester powder of Ackzonoble or Paint with 60 to 70 micron thickness. |
| 14 | Supply & fixing Equipment for open jym as per following details. Item should be fix properly including E/W & C.C. in M-20 as per requirement.STANDING AND SEATING TWISTER:-• DIMENSIONS: - 1700mm (Length) x 540mm (Width) x 1250mm. (Height).• SAFE AREA: - 3 Mtr x 1Mtr.• Seating & Standing Twister equipment made from “C” Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters• The Center Pipe is of 100mm NB made from “C” Class G.I. Round Pipe.• The M.S. round plate of Ø250 mm & 10mm thickness is welded at bottom.• Handle and Bottom sleeve pipe of 125mm OD with thickness 5mm provided for easy assembly, replacement and maintenance.• The bottom frame of the Seating & Standing twister is of 32 NB, 50 NB, and 25 NB made from “C” class G.I. pipe.• The handle frame of Seating & Standing twister is 25 NB & Foot resting frame of seating side is made from “C” class G.I. pipe of 25mm NB.• The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “C” class, Welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRCA square pipes of 3mm thickness.• The Twister plate fitted on the bottom frame is made up of M.S. Round Plate of size 300mm diameter and 10mm thickness.• Closing Caps are made up of high quality Fiber reinforced Plastic material.• The Pins used are made up of Ø 35 mm SAE 8620 bright material.• The bearings used are of “6205zz” permanent lubricated sealed bearing of reputed brand.• High tensile steel with galvanized nuts & bolts are used for assembly.• The powder coating is done by Pure Polyester powder of Berger Paint with 60 to 70 micron thickness. |
| 15 | Supply & fixing Equipment for open jym as per following details. Item should be fix properly including E/W & C.C. in M-20 as per requirement.SURFING BOARD :-DIMENSIONS: - 1000mm (Length) x 600mm (Width) x 1400mm.(Height).• Safe Area:-1.5 x 1.3Mtr.• Surfing Board Equipment made from “C” Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters• The main frame is of 80mm NB made from “C” class G.I. pipe.• The bottom support welded of M.S. plate of Ø 250 mm & 10mm thickness.• The handle frame is of 25NB made from “C” class G.I. pipe.• The foundation used for fixing is a structure and made from center pipe of G.I. of 80NB “C” class welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness.• Bushes are used 70mm Outer Diameter with 5mm thickness is used.• The footrests made from high quality fiber reinforced plastic.• Closing Caps are made up of high quality Fiber reinforced Plastic material.• The pins used are made up of Ø35 mm SAE 8620 bright material.• The bearing used are of “6007zz” permanent lubricated sealed bearing of reputed brand.• High tensile steel with galvanized nut bolts are used for assembly.• The cerclips used for assembly is of A34.• The powder coating is done with Pure Polyester powder of Ackzonoble or Paint with minimum 60 to 70 micron thickness. |
| 16 | Supply & fixing Equipment for open jym as per following details. Item should be fix properly including E/W & C.C. in M-20 as per requirement.CROSS TRAINER :-• DIMENSIONS: - 1320mm (Length) x 600mm (Width) x 1750mm. (Height).• SAFE AREA: - 1.77 x 1.2Mtr.• Cross trainer equipment made from “C” Class G.I. Pipe of different NB. • The main frame Pipes are of 80NB “C” Class G.I. Pipe with single bend pipe with 250mm radius.• The bottom support of M.S. round plate of Ø250 mm & 10mm thick.• The Handle Frame is made up of 25NB “C” Class G.I. Pipe.• The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “C” class welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. • To build structure bushes are used which are made from M.S.seamless pipe of 60mm OD. With 5 mm thickness.• The footrests are made from Aluminum casting material of size 130 mm X 310mmX5mm thickness and mounted on M.S. Plate of Size 130mmx310mmx3mm thick• Closing Caps are made up of high quality Fiber reinforced Plastic material.• Pins used of Diameter 35mm, 25mm, and 17mm are made up from SAE 8620 bright .• The Bearings used are of “6007zz” “6205zz” and “6203zz” permanent lubricated sealed bearing of reputed brand.• High tensile steel with galvanized nuts and bolts are used for assembly.• The powder coating is done with Pure Polyester powders of Ackzonoble or Paints with 60 to 70 Micron thickness.• A16 , A 24 mm circlips are used for assembly.• Bolt M8X16 mm and NY lock nut of M8 made of SS 304 used on nylon cap mounted on pins to protect bearings and pins from rain and dust. |
| 17 | Supply & fixing Equipment for open jym as per following details. Item should be fix properly including E/W & C.C. in M-20 as per requirement.SIT UP & PULL BOARD DOUBLE:-• PRODUCT DIMENSIONS: - 1760mm (Length) x 1140mm (Width) x 660mm (Height).• SAFE WORKOUT AREA: - 2500mm (Length) x 1600mm (Width).• The Sit up Board double made from “C” Class GI pipe. Center column made from 100mm NB “C” class G.I. Pipe. • The main frame is of 25mm NB made from “C” Class GI pipe. FRP sheet of 3mm thickness is molded on main frame.• The remaining frame of the sit up board is of 32mm NB made from “C” class GI pipe.• The powder coating is done with Pure Polyester powder Ackzonoble or Berger Paints with 60 to 70 micron thickness.• The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “C”class Welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. |
| 18 | Supply & fixing Equipment for open jym as per following details. Item should be fix properly including E/W & C.C. in M-20 as per requirement.Shoulder Wheel:-• DIMENSIONS: -900mm (Length) x 750mm (Width) x 1703mm. (Height).• SAFE AREA: - 2 Mtr x 1Mtr.• palm whell equipment made from “C” Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters• The Center Pipe is of 100mm NB made from “C” Class G.I. Round Pipe.• The M.S. round plate of Ø250 mm & 10mm thickness is welded at bottom.• Handle and Bottom sleeve pipe of 125mm OD with thickness 5mm provided for easy assembly, replacement and maintenance.• The bottom frame of the Seating & Standing twister is of 32 NB, 50 NB, and 25 NB made from “C” class G.I. pipe.• The handle frame of Seating & Standing twister is 25 NB & Foot resting frame of seating side is made from “C” class G.I. pipe of 25mm NB.• The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “C” class, Welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRCA square pipes of 3mm thickness.• The Twister plate fitted on the bottom frame is made up of M.S. Round Plate of size 300mm diameter and 10mm thickness.• Closing Caps are made up of high quality Fiber reinforced Plastic material.• The Pins used are made up of Ø 35 mm SAE 8620 bright material.• The bearings used are of “6205zz” permanent lubricated sealed bearing of reputed brand.• High tensile steel with galvanized nuts & bolts are used for assembly.• The powder coating is done by Pure Polyester powder of Berger Paint with 60 to 70 micron thickness. |
| 19 | Providing Fixing & Installation at site of Arch Swing Two Seater:- Sate play area- 4MTr.X2.5 Mtr. Height 2.4 mtr. Its total required area 3 Mtr. X 1.5 mtr. And height shall be 2.4 mtr. From ground Level top bar of swing is made by 80 mm IDGI pipe 12 gauge. And 4 nos. of leg. support pipe should be 80 mm IDGI pipe 12 gauge. Top bar attach with 2 nos. of alloy steel costing bearing with GI chain. Seating arrangement of Swing are made up of 10 mm thick. Anti skid chequered reinforced rubber belt. Bearing should be coveredd be sepcially design nylon clamp. The pure polyster powder coating (over baked) done on the pipe extend the life of equipments. And install be C.C Base in charge. |
| 20 | Providing Fixing & Installation at site of FRP Wave Slide- Safe play Area- 5.2 mtr.X 0.6 mtr. Platform height 1.8 mtr. From ground level connected with leg support 48 mm NB pipe & Ladder should be made by steel frame with sheet 16 G. (CRC) sheet 1.54 mm thick and supported by MS curt angle. Realing should be made by 25 MM NB pipe. Total slide length 3.8 Mtr. With 5 mm FRP thick overall both side finish. All the sharp edges and corner properly grinded to give smooth finishing so that children are not hurt with playing on it. The pure polyster powder coating. (over baked) done on the pipes extend the life of equipments. Slide should be made in a single mould piece there is no any joint in the slide. FRP components should be paint by 3 layer of PU paint. And install bv C.C base system as per order be engine. |
| 21 | DELUXE MULTISEATER SEE SAW:- PRODUCT AREA: MINIMUM 2500 MM X 350 MM. SAFE PLAYAREA: MINIMUM 4500 MM X 1500 MM. SEE SAW LEVER IS MADE UP OF MINIMUM 100 NB GI B CLASS PIPES. LEVER LENGTH WILLBE MINIMUM 2500 MM LONG. LEVER ENDS ARE COVERED WITH GI PIPE END CAP. FOUR NO OF SEATS ARE MADE UP OF LLDPE PLASTIC WITH INBUILT HANDLE. STAND IS MADE UP OF MINIMUM 80 NB GI B-CLASS PIPES. TWO NO OF PEDESTAL BEARING ARE GIVEN FOR SMOOTH AND NOISELESS MOVEMENT OF SEE SAW LEVER. BEARING IS COVERED WITH NYLON COVER. BARCODE ON MACHINE TO SHOW THE PROPER USE OF MACHINE. WORKOUT CARD & DIET CARD SHOULD BE SHOW IN APP. CUSTOMER CAN BOOK HIS ASSESMENT FROM HIS LOCATION. ALL MUST BE COMPATIBLE IN IOS AND ANDROID FOR BOOK THE SLOT AND TICKETS. EQUIPMENT MUST BE MADE AND CONFIRMS WITH THE APPROVED STANDARDS CERTIFIED BY AND CERTIFICATES ARE MANDATORY REQUIRES IN THE NAME OF BOTH TENDERS ACT AS BIDDER AND MANUFACTURER. THE EQUIPMENT MUST ACCOMPAINED WITH TEST REPORT FOR QUALITY, SAFETY, DURABILITY AND PROPER FUNCTIONING OF EQUIPMENT MUST MANDATORY REQUIRES TEST REPORT IN THE NAME OF BOTH TENDERER ACT AS BIDDER AND MANUFACTURER. |
| 22 | STRAIGHTS SLIDE Providing,supply and fixing of straight slide SAFE PLAY AREA - 10 ft . X 3 ftHeight - 5 ftsFrom ground level connected with leg support 48 mm Od pipe & Ladder Should pe made by ms pipe. Total slide Length will be 10 ft . with 5mm thickness overall both side finish . all the sharp edges & corner properly grined to give smooth finishing so that children are not hurt with playing it . Its Should be FRP Straight Slide. Colour of the Equipments will be choose by Engineer in Charge . Slide Should be made in a single mould Piece there is no any joint in the slide. Ladder should be paint by spray paint process. and Install in C.C Base M-20 as per the direction given by Engineer -in-Charge. |
| 23 | TUBE SLIDE Providing,supply and fixing SAFE PLAY AREA - 10 fts . X 3 ftsHeight - 5 ftsFrom ground level connected with leg support 48 mm Od pipe & Ladder Should pe made by ms pipe . Total slide Length will be 10 fts . with 5mm thickness overall both side finish . all the sharp edges & corner properly grined to give smooth finishing so that children are not hurt with playing it . Its Should be FRP Tube Slide . Colour of the Equipments will be choose by Engineer in Charge. Slide Should be made in a Jointable model Piece there is 4 - 5 joint in the slide . Ladder should be paint by spray paint process. and Install in C.C Base M-20 as per the direction given by Engineer -in-Charge. |
| 24 | SPIRAL SLIDE Providing,supply and fixing SAFE PLAY AREA - 10 fts . X 6 ftsHeight - 5 ftsSpiral Slide From ground level connected with leg support 48 mm Od pipe & Ladder Should pe made by ms pipe . Total slide Length will be 10 fts . with 5mm thickness overall both side finish . all the sharp edges & corner properly grined to give smooth finishing so that children are not hurt with playing it . Its Should be FRP Spiral Slide . Colour of the Equipments will be choose by Engineer in Charge. Slide Should be made in Single Mould Piece there is no joint in the slide . Ladder should be paint by spray paint process. and Install in C.C Base M-20 as per the direction given by Engineer -in-Charge. |
| 25 | Providing,supply and fixing play system SAFE PLAY AREA - 11 fts . X 13 ftsHeight - 8 fts* Multi Play Have 1 See Saw & 1 Swing & 1 FRP Straights Slide From ground level connected with leg support 48 mm Od pipe & Ladder Should pe made by ms pipe . Total slide Length will be 10 fts . with 5mm thickness overall both side finish . all the sharp edges & corner properly grined to give smooth finishing so that children are not hurt with playing it . Its Should be FRP Straight Slide . Colour of the Equipments will be choose by Engineer in Charge. see saw will be fixed in C.C base M-20. Slide Should be made in a single mould Piece there is no any joint in the slide . Ladder should be paint by spray paint process. and Install in C.C Base as per the direction given by Engineer -in-Charge. Please Enable Macros to View BoQ information |
