|
| 1 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 2 | Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, scaffolding, washing of floors and taxes all complete as per building specification and direction of E/l. |
| 3 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade :New work (Two or more coats applied @ 1.43 ltr/ 10 sqm overand including priming coat of exterior primer applied @ 2.20kg/ 10 sqm) |
| 4 | Dismantling old plaster and pointing in cement or lime and raking out joints to 15mm depth, watering and disposal of unserviceable materials with all leads all complete as per direction of E/I. |
| 5 | Providing 12mm cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I. |
| 6 | Providing 6mm cement plaster (1:4) in celling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I. |
| 7 | Providing and laying in position specified grade of cement concrete,excluding the coat of centering and shuttering -All work up to -Plinth level: 1:1.5.3 (1 Cement : 1.5 Coarse sand (Zone iii) : 3 Graded stone aggregate 20mm nominal size ) |
| 8 | Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer 3 mm thick water proofing membrane, black finished reinforced with non-woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrane manufacture of density at 25°C, 0.87-0.89 kg/ litre and viscocity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torch and sealing all joints etc, and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 650/ 450N/ 5cm. Tear strength in longitudinal and transverse direction as 300/250N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane : |
| 9 | Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. |
| 10 | Providing and laying 1stquality Ceramic glazed wall tiles thickness to be specified by themanufacturer) in walls over 12 mm cement mortar (1:3)and jointed with grey cement slurry flushpointed with white cement including rubbing polishing and cost of curing, taxes and royalty all complete as per building specification and direction |
| 11 | Providing and laying Doublecharge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 / ISO 13006 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm . |
| 12 | Providing primer one coat of red lead paint of approved make over steel surface including preparing the surface after cleaning removing dirt, scales, grease and sand papering, including cost of scaffolding etc. all complete as per building specification direction of E/I. |
| 13 | Providing 2 coats of Synthetic Enamel Paint of approved shade and make over steel surface grills & railings including cleaning the surface thoroughly scaffolding and taxes all complete as per building specification and direction of E/I. |
| 14 | Providing 150mm. Wide brick drain in cement mortar (1:6) with av. 150mm clear depth and 125mm apron including cost of eartwork involved with 75mm cement concrete (1:4:3) over one brick designation 75A flat soling in proper grade and slope at the base the drain duly plastered in C.M. (1:3) with punning over exposed surface all complete as per building specification and direction of E/I. |
| 15 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. |
| 16 | Providing and fixing T-iron frames for doors, windows and ventilators of of mild steel Tee-sections, joints mitred and welded, including fixing necessary butt hinges and screws and applying a priming coat of approved steel primer. Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately) |
| 17 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. |
| 18 | Providing and laying in position specified grade of cement concrete,excluding the coat of centering and shuttering -All work up to -Plinth level: 1:1.5.3 (1 Cement : 1.5 Coarse sand (Zone iii) : 3 Graded stone aggregate 20mm nominal size ) |
| 19 | Supplying, fitting and fixing 20 guage G.C.I. Sheet gate fitted on M.S. Angle frame of size 60X60X6mm. Including cost of fabrication, providing necessary locking arrangement with haskal and domny duly fixed in P.C.C. (1:2:4) blocks of required size applying a priming red lead paint over steel work, taxes all complete as per drawing specification and direction of E/I. |
| 20 | Carriage of materials by diesel Truck including loading at source, unloading at works site and stacking properly, labour, P.O.L., etc. all complete as per direction of E/I. |
| 21 | Sand lead - 10 km |
| 22 | Stone chips lead - 22 km |
| 23 | Bricks lead 8km(1k+7p) |
| 24 | Supplying, fitting and fixing vitreous white glazed earthen ware I.W.C. Of parry Hindustan or any other I.S.S. Approved make with 100mm H.C.I. 'P' trap 15liters C.I. Pull and let go flushing cistern of names or other I.S.S. Equipment make, complete with all fittings, C.I. or C.C. brackets 32mm alkathene/P.V.C. telescopic flush, pipe about 2 M long with one brass coupling and clamps G.I. chain and pull including supplying and fixing a pert of vitreous white glazed earthenwere were footrest to be fixed in floor 15mm C.I. body brass spindle stope cock of weight not less than 50grms, 15mm P.V.C. connection pipe 450mm long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/I: (A) 580 mm.lonq (b) With 12.5 lit. low level C.l. cistern |
| 25 | Supplying, fitting and fixing viterous white glazed earthen ware wash hand basin of Parry or Hindustan or any other I.S.S. approved make supported on pointed C.l. or R.S. brackets 32 m C.I. brass waste 15 mm dia C.I. body brass spindle stop cock of approved quality of weight not less than 350grms., 32 mm P.V.C. waste pipe 750mm long with brass coupling at one end and making plumber joints etc. all complete as per specification and direction of E/l. |
| 26 | Providing and placing on terrace (at all floor levels) polyethylene waterstorage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflowpipes but withoutfittings and the base support for tank. |
| 27 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, havingthermal stability for hot & cold water supply, including all CPVC plain &brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cementand the cost of cutting chases and making good the same including testingof joints complete as per direction of Engineer in ChargeEarth work in excavation in foundation trenches in ordinary soil (vide classification of soil item-A) and do - do - as per approved design, building specification and direction of E/l. |
| 28 | 15 mm nominal dia Pipes |
| 29 | 20 mm nominal dia Pipes |
| 30 | Providing and fixing Gun metal full way valve of approved qualtiy, all complete as per specification and direction of E/l. |
| 31 | (a) 20mm dia |
| 32 | (b) 25mm dia |
| 33 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion,(i) Single socketed pipes.12.41.2 110 mm diameter |
| 34 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. |
| 35 | Single tee with door-110mm dia |
| 36 | Plain tee - 110mm |
| 37 | plain band - 110mm |
| 38 | S/F Modular type switch socket - Supplying and fixing following modular type switch/socket on the existing modular plate and switch box including connection but excluding modular plate etc. as required |
| 39 | 5/6 amps, one way modular switch |
| 40 | 5/6 amps, 3 pin modular socket |
| 41 | 15/16 amps , 6 pin socket outlet |
| 42 | 15/16 amps , two way switch |
| 43 | S.I.T.C. of following rating, surface mounted LED light fitting, suitable for 230V 50Hz, single phase supply etc. complete as required. |
| 44 | 20/22W LED Tube Light |
| 45 | 15/16 Watt LED Bulb |
| 46 | Supply, Installation, testing and commissioning of following, size ceiling fan 3 Blades confirming to IS : 374 : 2019 including wiring the down rods of standard length (up to 30cm) with 1.5 sq.mm. FR PVC insulated, copper wire suitable for 230V 50Hz, single phase supply etc. complete as required. |
| 47 | 1200mm (48\\") ceiling Fan |
| 48 | 12\\" (300mm) metal exhaust fan |
| 49 | 2x1.5 sq mm + 1x1.5 sq mm earth wire |
| 50 | 2x2.5 sq mm + 1x2.5 sq mm earth wire |
| 51 | Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (with charcoal or coke andsalt) as required. |
| 52 | Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess forconnections etc. as required |
| 53 | Providing and fixing 6 SWG dia G.I. wire on surface or in recess forloop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required. |
| 54 | Add 18 % GST (in Basic Rate must fill 12) |
| 55 | Add 1% Labour Cess (in Basic Rate must fill 1) Please Enable Macros to View BoQ information |
