Tender For Construction Of Govt. Senior Secondary School At Kiar Koti, District Shimla (Hp). (Sh:- Construction Of Building Portion Including Water Supply & Sanitary Installation, Septic Tank And Rain Water Harvesting System., Shimla-Himachal Pradesh

TDR : 54597168

Tender Notice
BOQ

8 Days Left

Shimla , Himachal Pradesh

Tender Brief : Tender For Construction Of Govt. Senior Secondary School At Kiar Koti, District Shimla (Hp). (Sh:- Construction Of Building Portion Including Water Supply & Sanitary Installation, Septic Tank And Rain Water Harvesting System.

Document Fees
₹ 7000 /-

EMD
₹ 613200.0 /-

Tender Value
Refer document

Submission Date
20-03-2026

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains of soil such as pick work, jumper work, blasting work, jumper blasting work soft and hard blasting and saturated soil, de-watering, including wedging out rocks where blasting is prohibited, chiseling or any other mixed variety of soil, including shoring, strutting or bailing out water upto any depth or any height quantum of water including dewatering removal of slush and stacking the serviceable and unserviceable material clear from the edge of excavation and as per direction of Engineer-In-Charge and retuning the stacked soil in 15 cm (Fifteen centimetre) layers, when required into plinths, side of foundation etcetra consolidating each deposited layer by ramming watering and then disposing of all excavated earth as directed by the Engineer-In-Charge, within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
2	Excavating trenches of required width for pipes, cables, etcetra including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m (One point five metre), including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm (Twenty centimetres) in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m (Fifty metre) Pipes, cables etc. exceeding 80 mm (Eighty milimetres) dia. but not exceeding 300 mm (Three hundred milimetres) dia complete in all respect including carriage of material within all leads, lifts and other. incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
3	Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights/depth of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in Foundation footings, bases of columns and mass concrete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design, entire satisfaction and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
4	Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights/depth of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in flat surfaces such as soffits of suspended floors roofs, landings balconies and access platform including carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
5	Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera; with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in Lintals beams, plinth beams, cantilevers, girders, including carriage of material within all leads, lifts and other incidentals as per approved drawing, design, specifications, entire satisfaction and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
6	Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in columns, pillar, piers, abutments, post and struts including carriage of material within all leads, lifts and other incidentals as per approved drawing, design, specifications and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
7	Providing form work with steel plates of 3.15mm (Three decimal fifteen millimetres) thick, welded with angle iron in frames of 30x30x5mm(Thirty into Thirty into Five millimetres),so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights and removal of the same for in-situ reinforced and plain concrete work in stairs cases with slopping or stepped soffits, (excluding landing) except spiral staircase including carriage of material within all leads, lifts and other incidentals as per approved drawing, design, specifications and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
8	Providing form work with steel plates of 3.15mm (Three decimal fifteen millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights and removal of the same for in-situ reinforced and plain concrete work in edges of slab and breaks in floors and walls under any thickness including carriage of material within all leads, lifts and other incidentals as per approved drawing, design, specifications and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
9	Providing form work with steel plates 3.15mm (Three point one five millimeters) thick, welded with angle iron in frame 30x30x5mm (Thirty isto Thirty isto Five millimeters) so as to give a fair finish including centering, shuttering strutting and propping etcetera with wooden battens and ballies, height of propping and centering in all heights. below supporting floor to ceiling and removal of the same for in situ reinforced concrete and plain concrete work in Small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like upto all floor level including carriage of materials within all leads, lifts and upto any other incidential as per drawings and technical specifications and as per the direction of Engineer-In-Charge .The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
10	Providing form work with steel plates of 3.15mm (Three decimal fifteen millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights and removal of the same for in-situ reinforced and plain concrete work in Walls (any thickness) including carriage of material within all leads, lifts and other incidentals as per approved drawing, design, specifications and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
11	Providing and laying in position cement concrete 1:4:8 (One cement isto four sand isto eight graded broken/crushed stone aggregate 40mm (Forty millimetres) nominal size mechanically mixed and vibrated curing complete excluding the cost of centering and shuttering in foundation and plinth including carriage of material within all leads, lifts and other incidentals as per approved drawing, design, specifications and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
12	Stone Filling in plinth with approved stone under floors including watering, ramming, consolidating and dressing complete including carriage of material within all leads, lifts and other incidentals as per approved drawing, design, specifications and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
13	Supplying and filling broken/ crushed stone/ brick bats of hard stone of 40 mm size in filter tank including carriage of material within all leads, lifts and other incidentals as per approved drawing, design, specifications and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
14	Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete including carriage of material within all leads, lifts and other incidentals. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
15	Providing and laying in position machine batched and machine mixed cement concrete work of grade M-25 (M-Twenty five ) design mix to obtain the compressive strength of 25 N/mm square (Twenty five Newton per square millimetre) for reinforced cement concrete work, using cement contents not less than @360 kg/cum (Three hundred sixty kilogram per cubic metre) or as per approved design mix for the work upto plinth level to give a smooth surfaces mechanically mixed and vibrated including curring complete and pumping of concrete to site of laying excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability complete including carriage of material within all leads, lifts and other incidentals as per approved drawing, design, specifications and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
16	Providing and laying in position machine batched and machine mixed cement concrete work of grade M-25 (M-Twenty five) design mix to obtain the compressive strength of 25 N/mm square (Twenty five Newton per square millimetre) for reinforced cement concrete work, using cement contents not less than @ 360 kg/cum (Three hundred sixty kilogram per cubic metre) or as per approved design mix for All works above plinth level to all floor level to give a smooth surfaces mechanically mixed and vibrated including curring complete and pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability complete including carriage of material within all leads, lifts and other incidentals as per approved drawing, design, specifications and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
17	Providing and laying in position machine batched and machine mixed cement concrete work of grade M-20 (M-Twenty) design mix to obtain the compressive strength of 25 N/mm square (Twenty five Newton per square millimetre) for reinforced cement concrete work, using cement contents not less than @ 320 kg/cum (Three hundred twenty kilogram per cubic metre) or as per approved design mix for All works above plinth level to all floor level to give a smooth surfaces mechanically mixed and vibrated including curring complete and pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability complete including carriage of material within all leads, lifts and other incidentals as per approved drawing, design, specifications and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
18	Square rubble masonry coursed with hard stone of approved quality in foundation and plinth including racking out joints in cement mortar 1:6 (One cement isto six coarse sand) complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
19	Providing Tor steel reinforcement Thermo Mechanically Treated bars of grade Fe-500D of Tata Tiscon/Sail for reinforced cement concrete work including bending, binding, cutting, straightening and placing in position complete including cost of binding wires complete upto all floor levels as per approved specifications, drawing, design, as per entire satsfaction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
20	Providing and laying Damp Proof Course 100mm (One hundred millimetre) thick with cement concrete 1:2:4 (one cement: two sand: four graded/crushed stone aggregate) 20mm (Twenty millimetre nominal size) and curing complete, as required at site including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
21	Providing and applying a coat of residual petroleum bitumen of grade VG-10 (Viscosity grade-Ten) of approved quality using 1.70 Kgs. (one decimal seven zero Kilogram) per square metre on Damp Proof Course after cleaning the surface with a piece of cloth lightly soaked in kerosene oil, including carriage of material within all leads, lifts and other incidentals as per approved specifications, drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
22	Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (Seven point five) in superstructure above plinth up to all floor level in cement mortar 1:4 (One cement isto four sand) and curing complete including carriage of material within all leads, lifts and other incidentals as per approved specifications, drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
23	Brick work using Second class common burnt clay building bricks in super-structure upto all floor level in cement mortar 1:6 (One cement isto Six sand) and curing complete including carriage of material within all leads, lifts and other incidentals as per approved specifications, drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
24	Brick work using Second class common burnt clay building bricks in foundation and plinth in cement mortar 1:4 (One cement isto four sand) and curing complete including carriage of material within all leads, lifts and other incidentals as per approved specifications, drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
25	Providing and fixing 35mm (Thirty five millimetre) thick factory made decorative prelaminated ISI marked flush door shutters of Marino or its equivalent with 6mm (six millimetre) thick hard wood edging conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st (first) class hard wood and well matched teak 3 (three) ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. etcetera complete as per specifications, drawing and design including carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
26	Providing and fixing 35 mm (Thirty five millimetre) thick factory made decorative prelaminated ISI marked flush door shutters of Marino or its equivalent with 6mm thick hard wood edging and providing vision panel not exceeding 0.1 sqm (zero decimal one square metre) in all type of flush doors (cost of glass excluded) (overall area of door shutter to be measured): conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st (first) class hard wood and well matched teak 3 (three) ply veneering with vertical grains or cross bands and face veneers on both faces of shutters etcetera complete as per specifications, drawing and design including carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
27	Providing and fixing M.S. grills of required pattern in frames of windows etcetra with M.S. flats, square or round bars etcetra including priming coat with approved steel primer all complete fixed to steel windows by welding complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
28	Providing and fixing cold roll framed of NCL seclor 5000 series / ELXIR 3000 series roll formed section of size 105x60mm (One hundred five into Sixty milimetres) for outer door and internal door & partition wall single rebate. Door frames are made up of Galvanized powder coated steel section of 1.2 mm (one decimal two millimetre) thickness. These frames are povide with a groove for gaket to give perfect sealing for single rebate doors frame. Powder frames of all doors 3 nos of m.s. powder coated 4\\" (Four Inches) butt hinges of 2mm (Two milimetres) thickness welded to the frame, 6 (Six) numbers 1.2mm (One decimal Two milimetres) thick crca electroplated stiffeners should be welded to the frame, 6 (Six) numbers 8\\" (Inches) M.S. hold fasts with split end tail welded to stiffener plates, one no aldrop receiver. Each frame shall be provided with 25x50mm (Twenty five into Fifty milimettres) section as tie rod at the bottom. all welded places shall be treated with protective coat of zinc rich primer.the entire frame should be provided with a coat of etched primer &powder coated with pure polyester powder upto 50-60 (Fifty-Sixty) microns and door frames can be filled with puf as per Architect Standard design, specification complete including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
29	Providing and fixing windows fabricated from roll formed sections made of galvanized steel colour coated / powder coated (base steel as per is 513 \\"D\\" quality, hot dip galvanized as per IS 277 with zinc of 120 grams/sq. mtr.) with total coated thickness 0.72 mm for outer frame & 0.58 mm for other sections coated section should have a coat of epoxy primer of 5-7 microns thick finish painted with a polyster paint of 12-16 microns thick & back coated with Alkyd backer of 5-7 microns of powder coated with pure polyester powder upto 50-60 microns thick. Section for frame should be made of 98x50x0.72mm thickenss section for mullion should be of 46x70x0.58mm thickness, sections for additional mullion should be of 30x44x0.72mm thickness, section for shutter frame should be of 46x46x0.58mm thickness, section for fixed glass bead should be of 18x25x0.58mm thickness & Section for fly meash shutter should be 20x40x0.58mm thickness & section for mesh fixing should be 18x6x0.58mm thickness. All glazed shutter should be provided with one set of MS powder coated friction hinges, one number of of high grade aluminium powder coated handle, each mesh shutter should be provided with set of pivot hinges & Section colour make handle & Latch. glass panes should be 5mm toughened KT series fixed window glass. The glass shall be without any flaws, buvvles, scratches etetra including steel glazed doors, windows and ventilators of standard rolled steel sections joints mitred and welded with 16x3.15mm (Sixteen into Three decimal fiftee milimetres) lugs 10cm (Ten centimetres) long embedded in cement concrete blocks 15x10x10cm (Fifteen into en into Ten centimetres) size of 1:3:6 (Ome cement: Three sand : Six graded stone aggregate 20mm (Twenty milimetres) nominal size) or with wooden plugs and screws or rawl plug and screws or with fixing clips or with bolts and nuts as required and iron fittings, including providing and fixing glass panes with glazing clips and special metal sash putty, of approved make and wire mesh as per Architect Standard design, specification complete including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
30	Providing and fixing 35 mm (thirty five millimetre) thick factory made decorative prelaminated ISI marked flush door shutters of Marino or its equivalent shall be finished from inside P.G.I. Sheet Linning conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st (first) class hard wood and well matched teak 3 (three) ply veneering with vertical grains or cross bands and face veneers on both faces of shutters etcetera complete as per specifications, drawing and design including carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-In-Charge.The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
31	Providing and fixing Glazing with glass panes of 5mm ( Five milimetre) thick plain glass weight not less than 12.50Kg/M2 (Thirteen point seven five Kilogramme per square metre) of Modi Guard / Saint Gobain / AIS / Atul / Gold Plus glazing in steel door, window, ventilator shutters and partitions etcetra with EPDM rubber / neoprene gasket as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
32	Providing and fixing cupboards shall be made of 19 mm (nineteen millimetres) thick water proof termite resistant commercial board ISI marked is no. 1659 of approved shade & sample including shelves and as per specifications, approved Drawing and design complete including carriage of material within all leads, lifts and other incidentals as per approved specifications, drawing, design and as directed by the Engineer-In-Charge.The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
33	Providing and fixing back side of the cub board shall be of 6 mm (six millimetre) thick water proof ply and as per specifications, approved Drawing and design complete including carriage of material within all leads, lifts and other incidentals as per approved specifications, drawing, design and as directed by the Engineer-In-Charge.The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
34	Providing and fixing the cupboards 1mm (one millimetre) thick lamination ISI marked is no. 12823 of approved shade and sample and as per specifications, approved Drawing and design complete including carriage of material within all leads, lifts and other incidentals as per approved specifications, drawing, design and as directed by the Engineer-In-Charge.The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
35	oviding and fixing 2nd (second) class teak wood lipping/ moulded beading or taj beading of size 18 x 5 mm (eighteen into five millimetre) fixed with wooden adhesive of approved quality and screws/ nails on the edges of the Pre-laminated particle board complete including carriage of material within all leads, lifts and other incidentals as per approved specifications, drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
36	Providing and fixing cup-board shutter magnetic catcher with necessary screws etcetra complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
37	Providing and fixing 65x35mm (Sixty five into thirty five milllimetres) special quality bright finished brass cup-board locks or ward robe locks with six levers including necessary screws etcetra (Indian make of approved quality) complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
38	Providing and fixing Stainlesss steel curtain rail with rollers stop ends and brackets in pelmets with curtain rod of 25mm (Twenty five millimetres) dia and brackets complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
39	Providing and fixing 300x16mm (Three hundred into Sixteen millimetres) size aluminium Pilot/sheel sliding door bolts anodized transparent or dyed to required colour and shade with necessary screws etcetera including carriage of material within all leads, lifts and other. incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
40	Providing and fixing 250x16mm (two hundred fifty into Sixteen millimetres) size aluminium Pilot/sheel sliding door bolts anodized transparent or dyed to required colour and shade with necessary screws etcetera including carriage of material within all leads, lifts and other. incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
41	Providing and fixing 250x10mm (Two hundred fifty into Ten millimetres) nominal size aluminium Pilot/sheel tower bolt (Barrel type) of required colour and shade with necessary screws etcetra bright finished or black enameled with nuts and screws etcetra including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge.The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
42	Providing and fixing 150x10mm (One hundred fifty into Ten millimetres) nominal size aluminium Pilot/sheel tower bolt (Barrel type) of required colour and shade with necessary screws etcetra bright finished or black enameled with nuts and screws etcetra including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
43	Providing and fixing 150mm (One hundred fifty millimetres) nominal size aluminium Pilot/sheel handles to required colour or shade with necessary screws etcetra complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
44	Providing and fixing 125mm (One hundred twenty five millimetres) nominal size aluminium Pilot/sheel handles to required colour or shade with necessary screws etcetra complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
45	Providing and fixing aluminium PILOT/Sheel 250 mm (Two hundred fifty millimetres) size hooks and eyes complete including carriage of material within all leads, lifts and other. incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
46	Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS No. 3564, embossed on the body, door weight upto 35 kg ( thirty five kilogram) and door width upto 700 mm ( seven hundred milimetres), with necessary accessories and screws etcetera complete, as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-In-Charge, including carriage of material within all leads, lifts and other incidentals. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
47	Providing and fixing aluminium hanging twin rubber floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour and shade, with necessary screws etcetra complete including carriage of material within all leads, lifts and other. incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
48	Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm (twenty five into five millimetre) size, with top and bottom rail of T-iron 40x40x6 mm (forty into forty into six millimetre), with 40 mm dia (forty millimetre diametre) steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer. including carriage of material within all leads, lifts and other incidentals as per approved specifications, drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
49	Providing and laying 19mm (Nineteen millimetres) thick kota stone 55x55cm (Fifty five into fifty five centimetre) in flooring laid over 20mm (Twenty millimetres ) (average) thickness base of cement mortar 1:4 (one cement isto four sand) including proper water proofing treatment of pidilite or jointing with grey cement slurry mixed with pigment to match the shade of kota stone including rubbing and polishing complete including carriage of material within all leads, lifts and other incidentals as per approved specification drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
50	Kota stone slab 19 mm (nineteen millimetres) thick in risers of steps, skirting dado and pillars laid on 12 mm (Twelve millimetres) (average) thick cement mortar 1:3 (One cement isto Three sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs including rubbing and polishing complete including carriage of material within all leads, lifts and other incidentals and further as per specifications, approved drawing, design and as directed by the Engineer-In-Charge.The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
51	Providing and laying 605x 605mm x 10mm (Six hundred into six hundred millimetre) into ten millimetre thick Double Charge vetrified tiles of Kajaria / Orient -Bell / Nitco or its equivalent of approved shade and design, in flooring laid on a bed of 20mm (twenty millimetre) thick cement mortar 1:4 (One cement isto four sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
52	Providing and laying 605x 605mm x 10mm (Six hundred into six hundred millimetre) into ten millimetre thick Double Charge vetrified tiles of Kajaria / Orient -Bell / Nitco or its equivalent of approved shade and design, with water absorption less than 0.08% (Zero point zero eight percent) and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm (Twelve millimetre) thick bed of cement mortar 1:3 (One cement isto Three coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm (Three point three kilogram per suare metre) including grouting the joint with white cement & matching pigments etcetera complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
53	Providing and fixing 2.2mm (two decimal two millimetre) thick venyl Delight Flooring of LG plain or coloured, carbed or mosaic/metalled finish laid with approved adhesive on sub-floor (damp proofing treatment to be paid for separately) etcetera complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
54	Providing and laying 300X300 mm (three hundred into three hundred millimetre) Grade IV ceramic tiles of Kajaria / Orient & Bell / Nitco or its equivalent as per approved shade in flooring over 20 mm (Twnety millimetre)(average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (one cement isto four coarse sand) complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge.The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
55	Providing and laying 450x300 mm / 600x 300mm (four hundred fifty into three hundred millimetre oblique six hundred kinto three hundred millimetre) white Glazed Tiles Dado Of Kajaria / Orient & Bell / Nitco or its equivalent with cement mortar over 12 mm (Twelve millimetre) thick bed of cement mortar 1:3 (One cement isto Three coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm (Three point three kilogram per suare metre) including grouting the joint with white cement & matching pigments etcetera complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
56	Providing and laying 19 mm (Nineteen millimetre) thick Baroda Green stone slab with white marble band having Semi Round nosing in treads of stair laid over laid over 20 mm (twenty millimetre) thick base cement mortar 1:4 (one cement isto four coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etcetra complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
57	Providing and laying 19 mm (nineteen millimetre) thick Jaislmer stone slab with white marble band laid over 20mm (twenty millimetre) (average) thickness base of cement mortar 1:3 (One cement isto three sand) and jointed with grey cement slurry mixed with pigment to match the shade of granite stone including rubbing and polishing complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
58	Providing and laying 40 mm (forty millimetre) thick fine dressed red sand stone flooring over 20 mm (twenty millimetre) (average) thick base of cement mortar 1:5 (one cement isto five coarse sand), including pointing with cement mortar 1:2 (one cement isto two stone dust) with an admixture of pigment to match the shade of stone and as per directions and entire satisfaction of the Engineer-In-Charge, including carriage of material within all leads, lifts and other incidentals. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
59	Providing and laying 50 mm (fifty millimetre) thick cement concrete flooring 1:2:4 (one cement isto twenty sand isto four graded stone aggregate 20 mm (twenty millimetre) nominal size) laid in one layer finished with a floating coat of neat cement as per directions and entire satisfaction of the Engineer-In-Charge, including carriage of material within all leads, lifts and other incidentals. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
60	Providing and fixing Teak wood handrail 6.25 x 7.5 cm (six decimal twenty five into seven decimal five centimetre) fixed on MS hollow square baluster 19x19 mm (nineteen into nineteen millimetre) with M.S. flat 19x4mm (nineteen into four millimetre) with 3 (Three) nos @ 16 mm (sixteen millimetre) mid rail connected at the side of the baluster with fixtures T and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approved drawing , design and specifications as per approved drawing , design and specifications. (Teak wood handrail paid for separatelly) within all leads, lifts and other incidentals and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government
61	Providing and fixing 50mm dia (fifty millimetre) diametre M.S. hollow pipe handrail of ramp, slip resisance with round ends at two level at 75 & 90 cm (seventy five & ninety centimetre) height & extended 30 cm (thirty centimetre) beyond the top & bottom on the ramp or as per architect drawing, design welded with 25mm diametre baluster embedded in cement concrete @ 60cm C/C (at the rate sixty centimetre centre to centre) and jointing welding at top alongwith M.S. hollow pipe as per Architectural drawing, design and specification including entire carriage of materials within all leads, lifts and other incidentals and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
62	Providing and fixing railing over parapet having Readymade M.S. Hollow pipe (D-section) 50x50mm dia hand rail with M.S. flat 40x6mm (forty into six millimetre) as per detail and baluster of 19mm x 19mm (nineteen into nineteen millimetre) and applying a coat of red lead paint as per Architectural drawing, design and specification including entire carriage of materials within all leads, lifts and other incidentals and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
63	Providing and fixing Teak wood handrail 6.25 x 7.5 cm (six decimal twenty five into seven decimal five centimetre) fixed on MS hollow square baluster complete including carriage of material within all leads, lifts and other incidentals as per approved specifications, drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
64	Providing and fixing factory made ridges or hips having proper gola shape 60 cm (Sixty centimetres) overall with 0.60 mm (Zero point sixty millimetres) thick prepainted steel sheets of Tata / Sail / Reliance / Jindals steels in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 (Twenty millimetres) microns over 5 (five) microns primer coating + back coat of polyster of 5 (five) microns over 5 (five) microns primer coating fixing with prepainted iron J or L hooks, bolts & nuts 6 mm (Six millimetres) dia & prepainted G.I. limpet and bitumen washers complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
65	Providing and fixing valley 90cm (Ninety centimetres) overall 0.60mm (Zero point sixty millimetres) thick prepainted steel sheet of Tata Durashine / Sail / Reliance / Jindals steels in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of back coat of polyster of 5 (five) microns over 5 (five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (six millimetres) dia with prepainted G.I. limpet and bitumen washers complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
66	Providing and fixing 0.60 mm (Zero point sixty millimetres) thick prepainted steel sheet of Tata Durashine / Sail / Reliance / Jindals steels in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 (Twenty) microns over 5 (five) microns primer coating to back coat of polyster of 5 (five) microns over 5 (five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (Six millimetres) diametre with prepainted limpet and rubber washers complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
67	Providing and fixing 30cm (Thirty Centimetre) wide 25cm (Twenty five centimetre) deep 0.60mm (Zero point six zero millimetres) thick prepainted plain P.G.I. sheet gutter of Tata / Sail / Reliance / Jindals having dome shape grating fixed with bolts, nuts and washers etcetera including making necessary connections with rain water pipe complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
68	Providing and fixing M.S. B.P. sheet 2.0mm (Two point zero millimetres) thick eaves board/facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-In-Charge (Base members of steel work shall be measured and paid separately) including fixing complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
69	Providing water proofing treatment shall be done in two coats apply First coat of Dr. Fixit Torch SHIELD ( P - 3160- 3mm ) to the clean and saturated surface maintaining a coverage 0.60 sqm (Zero point six zero squate meter) per kilogram to achieve 1mm (one millimeter) thickness this coating shall also be executed up to 300mm (Three hundred millimetres) vertically. The 2nd (Second) coat shall be applied in opposite direction after 4 to 6 (Four to six) hours of application of 1st (First) coat then sprinkle sand on top surface of applied Dr. Fixit Fast flex white still tacky and the second coat. Then apply cement mortar 1 : 4 (one cement : four sand) and mixed with Pidiproof LW at the rate 200ml (two hundred millimetre) per 50 kg (Fifty kilogram) of cement over the floor with suitable gradient towords drain water pipe while the second coat of Dr. Fixit is still tacky complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
70	Providing and fixing flashing 38 cm (thirty centimetre) overall with 0.60 mm(zero point six zero millimetre) thick prepainted sheet of Tata Durashine / Sail / Reliance / Jindals steels in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of 20 (twenty) microns over 5 (five) microns primer coating + back coat of polyster of 5 (five) microns over 5 (five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia (six millimetre diametre) meter & prepainted G.I. limpet & bitumen washers complete as per approved drawing , design and specifications including carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-In-Charge.The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
71	Providing and fixing 150 mm (One hundred fifty millimetres) diametre on wall face PVC (D-Plast) rain water pipes of working pressure 4/6 Kg/cm2 (Four/six kilogramme per centimetre square) ISI marked of Finolex / Relpipe (Relience) / Vectus including filling the joints with approved adhesive complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
72	Providing and fixing 150mm (One hundred fifty millimetres) dia PVC Plain bend on wall face PVC rain water pipes working pressure 4/6 K.g/cm2 (Four/six kilogramme per centimetre square) ISI marked of Finolex / Relpipe (Relience) / Vectus including priming coat, painting and welding etcetra complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
73	Providing and fixing 150mm (One hundred fifty millimetres) dia PVC Shoe on wall face PVC rain water pipes working pressure 4/6 K.g/cm2 (Four/six kilogramme per centimetre square) ISI marked of Finolex / Relpipe (Relience) / Vectus including priming coat, painting and welding etcetra complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
74	Providing and fixing PVC holder bat clamps of approved design to HDP rain water pipe embedded including cement concrete blocks 10x10x20cm of 1:2:4 (One cement: Two sand: Four graded crushed stone aggregate 20mm (Twenty millimetres) nominal size and cost of cutting holes and making good the walls etcetra as per specifications, drawing and design including carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
75	Structural steel work of Tata / Sail / Reliance / Jindal riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
76	Painting Steel work (including priming coat) with enamel paint of Nerolac / Asian to give an even shade two or more coat applied @ 0.90 ltr/10 sqm (Zero point ninety litre per ten square metre) over an under coat of primer applied @ 0.80 ltr/10 sqm (Zero point eighty litre per ten square metre) of approved brand and manufacture including cleaning the surfaces of all dirt, dust and other foreign matter complete as per Architectural drawing, design and specification including entire carriage of materials within all leads, lifts and other incidentals and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
77	Painting wood work (including priming coat) with enamel paint of Nerolac/ Asian Paint of required shade two or more coat applied @ 0.90 ltr/10 sqm (Zero point ninety litre per ten square metre) over an under coat of primer applied @ 0.75 ltr/10 sqm (Zero point seven five litre per ten square metre) of approved brand and manufacture including cleaning the surfaces of all dirt, dust and other foreign matter complete as per specifications, drawing and design including carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
78	Providing and applying 6mm (Six millimetres) thick cement plaster to ceiling in cement mortar 1:3 (One cement : Three sand) upto all floor levels complete including carriage of material within all leads, lifts and other incidentals as per approved specifications, drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
79	Providing and applying 15mm (Fifteen millimetre) thick cement plasters in single coat on rough side of brick/concrete/stone walls for interior plastering upto all floor level including arises, internal rounded angles, chamfers or rounded angles not exceeding 80mm (Eighty millimetres) in girth and finished even and smooth witth cement mortar 1:6 (One cement : Six sand) above plinth level to floor all level complete including carriage of material with in all leads, lifts and other incidentals as per drawing, design and specifications, as per the direction and entire satisfaction of Engineer-In-Charge.The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
80	Providing and applying 15mm (Fifteen millimetre) thick cement plasters in single coat on fair side of brick/concrete/stone walls for interior plastering upto all floor level including arrises, internal rounded angles, chamfers and rounded angles not exceeding 80mm (Eighty millimetres) in girth and finished even and smooth with cement mortar 1:6 (One cement: Six sand) above plinth level to floor all level complete including carriage of material with in all leads, lifts and other incidentals as per drawing, design and specifications, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
81	Providing and applying 15mm (Fifteen millimetre) thick cement plasters in single coat on fair side of brick/concrete/stone walls for exterior plastering upto all floor level including arrises, internal rounded angles, chamfers and rounded angles not exceeding 80mm (Eighty millimetres) in girth and finished even and smooth with cement mortar 1:5 (One cement isto five sand) above plinth level to floor all level complete including carriage of material with in all leads, lifts and other incidentals as per drawing, design and specifications, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
82	Providing and applying 20mm (twenty millimetre) thick 10cm (ten centimetre) wide raised band in Plaster with cement mortar 1:4 (One cement isto four sand) complete including carriage of material with in all leads, lifts and other incidentals as per drawing, design and specifications, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
83	Providing and applying 20 mm (twenty millimetre) cement plaster in two coat backing coat 10 mm (ten millimetre) and finishing coat 10 mm (ten millimetre) thick on fair side of brick/stone masonary walls for interior plastering up to floor two level including aamses internal rounded angle chamfers and or rounded angle. Cement mortar 1:4 (one cement isto four sand) including carriage of material with in all leads, lifts and other incidentals as per drawing, design and specifications, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
84	Providing plinth protection with 40 mm ( Forty millimetre) thick interlocking paver block of NTC/Atlantic with 23 cm ( twenty three centimetre) dia half round RCC pipe for drainage purpose laid over 10cm (ten centimetre) thick cement concrete 1:4:8 (One cement isto four sand isto eight graded crushed stone aggregate) in bedding/ haunching complete including carriage of material with in all leads, lifts and other incidentals as per drawing, design and specifications, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
85	Providing and fixing decorative screen in coridor manufactured from 19mm x 19mm (nineteen into nineteen millimetre) hollow square pipes welded with M.S. hollow sections of size 50mm x 50mm (fifty into fifty millimetre), supported on 10 cm (ten centimetre diametre) M.S. hollow pipes. A centre piece shall be of 25 x 3mm (twenty five into three millimetre) M.S. flat frame covered with M.S. black sheet made to shape and applying a priming coat of approved steel primer using structural steel as per approved specifications, drawing, design, as per entire satsfaction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
86	Providing and applying white cement based putty of Birla white / JK average thickness 1mm (One millimetres) thick, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete upto all floor level complete including carriage of material with in all leads, lifts and other incidentals as per drawing, design and specifications, as per the direction and entire satisfaction of Engineer-In-Charge.The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
87	Finishing walls with apex weather proof exterior emulsion of Asian/Dulux/Berger/Nerolac Suraksha paints of approved shade having VOC less than 50 gm/litre (Fifty grams per liter) and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade with silicon additives New work (Two or more coats) applied @ 1.43 litre/ 10 sqm (One point forty three litre per ten square metre) over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm (Zero point ninety litre per ten square metre) upto all floor level complete including carriage of material with in all leads, lifts and other incidentals as per drawing, design and specifications, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
88	Wall painting (two or more coats) with acrylic washable emulsion of Asian paints / Berger paints/ Dulux paints/Nerolac paints (above Dado/skirting) of approved shade for interior painting with brushes plain smooth finish composed of acrylic polymere in emulsion inorganic,/special pigment siliceous aggregate anti fungicides anti-rusting & foaming in two coat including necessary putty to give smooth even surface, sand papered smooth complete including carriage of material with in all leads, lifts and other incidentals as per drawing, design and specifications, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
89	Painting (two or more coats) with satin enamel paint of Asian paints / Berger paints/ Dulux paints/Nerolac paints (above Dado/skirting) of approved brand and manufacture of required colour to give an even shade on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture complete including carriage of material with in all leads, lifts and other incidentals as per drawing, design and specifications, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
90	Wall painting with acrylic emulsion paint, Asian paints / Dulux paints / Nerolac paints / Berger Paints/ having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour complete, including carriage of material with in all leads, lifts and other incidentals as per drawing, design and specifications, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
91	Providing and fixing 600x600x6mm (Six hundred into six hundred into six millimetres) Everest fibre cement board ceiling panel with pre-painted GI channel framing @ 600mm (six hundred millimetres) centre to centre complete including carriage of material within all leads, lifts and other incidentals as per approved specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
92	Providing and laying plain cement concrete 1:2:4 (One cement isto two sand isto four graded crushed stone aggregate 20mm (twenty millimetre) nominal size & curing complete, excluding cost of form work in foundation and plinth as per approved specification, drawing and design including entire carriage of material with in all leads, lifts and other incidentals and further as per the direction and entire satisfaction of Engineer-in-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
93	Providing and laying 60mm (sixty millimetre) thick factory made cement concrete interlocking paver block of NTC / Unistone / Atlantic vibro compacted upto M50 (M-fifty) grade including border or kurb block grey or coloured over sub-base of concrete with 25mm (twenty five millimetre) thick average thickness of cement mortar 1:4 (one cement isto four sand) laid over and jointed with neat cement slurry mixed with pigment to match the shade of blocks i/c curing rubbing & polishing complete complete including carriage of material within all leads, lifts and other incidentals as per approved specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
94	Providing and laying plain cement concrete 1:3:6 (One cement isto three sand isto six graded crushed stone aggregate 40mm (forty millimetre) nominal size & curing complete, excluding cost of form work in foundation and plinth as per approved specification, drawing and design including entire carriage of material with in all leads, lifts and other incidentals and further as per the direction and entire satisfaction of Engineer-in-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
95	Providing and fixing 240x120 cm (two hundred forty into one hundred twenty) Black board having 12mm (twelve millimetre) thick green chalk board (non megnetic) with superior quality framing & square clamps fixed with the help of nylon sleves & screws as per site requirments . The board shall be fixed on the wall with specially designed j clamps. Blackboard shall have backing material of galvanized sheet 28mm (twenty eight millimetre) thick with top green surface for smooth writing with chalk over 11 mm (eleven millimetre) thick particle board. The board surface shall be non porus ceramic particles on the specially anodized aluminium Profile 20x15mm (twenty into fifteen millimetre) with corners of black plastic etcetra complete with in all leads, lifts and other incidentals as per drawing, design and specifications, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
96	Demolishing stone rubble masonry manually/ by mechanical means In cement mortar including stacking of serviceable material and disposal of unserviceable material with in all leads, lifts and other incidentals and further as per the direction and entire satisfaction of Engineer-in-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
97	Applying cement slurry on Reinforcement Cement concrete slab or cement concrete work using 2.75 kgs. (Two point seventy five Kilogram) Of cement per square meter of floor area before laying cement concrete flooring including roughening, cleaning of the concrete surfaces complete with in all leads, lifts and other incidentals as per drawing, design and specifications, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
98	Providing and fixing 1620 (20mm (Twenty millimetre) OD pipe) Polyethelene-Aluminium Polyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 1545 ,2004 of Kitec U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C (Eighty degree celcius), including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etcetra with clamps at 1.00 metre (One metre) spacing for concealed works, including cutting chases, testing the joint and making good the wall etcetera complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
99	Providing and fixing 2025 (25mm (Twenty five millimetre) OD pipe) Polyethelene-Aluminium Polyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 1545 ,2004 of Kitec U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C (Eighty degree celcius), including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etcetra with clamps at 1.00 metre (One metre) spacing for concealed works, including cutting chases, testing the joint and making good the wall etcetera complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
100	Making connection of galvanized mild steel distribution branch with galvanized mild steel main 20 to 40mm (Twenty to forty millimetre) nominal bore by providing and fixing tees including cutting and threading the pipe complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
101	Providing and fixing 110mm (One hundred ten millimetre) Nominal size/diameters in trenches P.V.C. Supreme/ Finolex pipe class \\"A\\" soil, waste and ventilating pipes 4/6 Kg/sqcm (Four/six Kilogram per square centimetres) thick fixing with approved adhesive mixure complete including entire carriage of materials complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
102	Providing and fixing 75mm (Seventy five millimetre) Nominal bore/diameters in trenches P.V.C. Supreme/ Finolex pipe class \\"A\\" soil, waste and ventilating pipes 4/6 Kg/sqcm (Four/six Kilogram per square centimetres) thick fixing with approved adhesive mixure complete including entire carriage of materials complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.
103	Providing and fixing 110mm (One hundred ten millimetre) Nominal bore/diameters P.V.C. clamps ISI marked including finishing with approved design with steel screws and rawl plugs etcetera complete in all floor level/height including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
104	Providing and fixing 75mm (Seventy five millimetre) Nominal bore/diameters P.V.C. clamps ISI marked including finishing with approved design with steel screws and rawl plugs etcetera complete in all floor level/height including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
105	Providing and fixing 110mm (One hundred ten millimetre) Nominal bore/diameters PVC Finolex / Relpipe (Relience) / Vectus heal rest Confirming to BIS-14735 including filling the joints with approved adhesive complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
106	Providing and fixing 75mm (Seventy five millimetre) Nominal bore/diameters PVC Finolex / Relpipe (Relience) / Vectus heal rest Confirming to BIS-14735 including filling the joints with approved adhesive complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
107	Providing and fixing 110mm (One hundred ten millimetre) Nominal bore/diameters PVC Finolex / Relpipe (Relience) / Vectus plain bend Confirming to IS No. 14735-99 including filling the joints with approved adhesive complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
108	Providing and fixing 75mm (Seventy five millimetre) Nominal bore/diameters PVC Finolex / Relpipe (Relience) / Vectus plain bend Confirming to IS No. 14735-99 including filling the joints with approved adhesive complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
109	Providing and fixing 110mm (One hundred ten millimetre) Nominal bore/diameters PVC Finolex / Relpipe (Relience) / Vectus Collars including filling with approved adhesive etcetera complete in all floor level/height including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge.The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
110	Providing and fixing 75mm (Seventy five millimetre) Nominal bore/diameters PVC Finolex / Relpipe (Relience) / Vectus Collars including filling with approved adhesive etcetera complete in all floor level/height including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
111	Providing and fixing 110mm (One hundred ten millimetre) Nominal bore/diameters PVC Finolex / Relpipe (Relience) / Vectus Cowl including filling with approved adhesive etcetera complete in all floor level/height including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
112	Providing and fixing 75mm (Seventy five millimetre) Nominal bore/diameters PVC Finolex / Relpipe (Relience) / Vectus Cowl including filling with approved adhesive etcetera complete in all floor level/height including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
113	Providing and fixing 110x90mm (One hundred ten millimeter into ninety milimeter) ISI marked P.V.C floor trap of Finolex / Relpipe (Relience) / Vectus of self cleaning design complete including fixing with approved adhesive cost of cutting and making good the walls and floors etc.complete within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
114	Providing and fixing 110x75mm (One hundred ten millimeter into ninety milimeter) ISI marked P.V.C floor trap of Finolex / Relpipe (Relience) / Vectus of self cleaning design complete including fixing with approved adhesive cost of cutting and making good the walls and floors etc.complete within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
115	Providing and fixing vitreous China wash down water closet (European type W.C. pan) WC Prima No 2090 with 10 (ten) litre low level PVC flushing cistern (Sleek plus) having dual flush system of Cera or its equivalent of star white / snow white shade with fitting and brackets, 40 mm (forty millimetre) flush bend, 20 mm (twenty millimetre) over flow pipe, with seat & lid fixed with C.P. brass hinges and rubber buffers,with specials of standard make and mosquito proof coupling of approved municipal design complete including painting of fittings and brackets, cutting and making good the walls and and fixed with jet pressure and intergal P or S trap including jointing the trap and soil pipe with adhesive of approved brand. (Jet Spray to be measured and paid for separately) complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
116	Providing and fixing water closet squatting pan (Indian type W.C. pan )White Vitreous china Orissa pattern W.C. pan no 2071 of size 580x440 mm (five hundred eighty into four hundred forty millimetre) with integral type foot rests with 100 mm (one hundred millimetre)sand cast Iron P or S trap, 10 (ten) litre low level P.V.C. flushing cistern,of Cera or its equivalent of star white / Snow white shade and as shown in the drawing / as per details including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
117	Providing and fixing 32 mm dia (thirty two millimetre diametre) P.V.C. flexible waste pipe of of Finolex / Relpipe (Relience) / Vectus for sink or wash basin including P.V.C. waste fittings complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
118	Providing and fixing G.I. inlet connection pipe for each flush pipe with W.C. pan complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
119	Providing and fixing vitreous China under counter wash basin Garnet No.10080 size 58x43Cm (fifty eight into forty three centimetre) of Cera or its equivalent of star white/snow white shade with single hole for pillar tap with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fittings complete as per Architectural drawing ,design and specifications complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
120	Providing and fixing 550x400mm (Five hundred fifty into four hundred millimetres) vitreous china wash basin Delta No. 10010 without pedestal of Cera or its equivalent with Mirror above of star white shade/snow white with single hole for pillar tap including 15 mm (Fifteen millimetre) nominal bore C.P. brass Pillar tap, 32mm (Thirty two millimetre) nominal bore C.P. brass waste with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fittings (Mirror to be measured and paid for seperately) complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
121	Providing and fixing vitreous china flat back range of two half stall urinal Large flat back no 5001 of size 63.3x39.5x42 cm (sixty three decimal three into thirty nine decimal five into forty two centimetre) with automatic flushing cistern of make Cera or its equivalent in white shade with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever require of snow white colour including connection with urinal and waste pipe by means of white lead mixed with chopped hemp (waste pipe to be measured and paid for separately) complete as per Architectural drawing ,design and specifications, complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
122	Providing and fixing vitreous china flat back single half stall urinal Large flat back no 5001 of size 63.3x39.5x42 cm (sixty three decimal three into thirty nine decimal five into forty two centimetre) with automatic flushing cistern of make Cera or its equivalent in white shade with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever require of snow white colour including connection with urinal and waste pipe by means of white lead mixed with chopped hemp (waste pipe to be measured and paid for separately) complete as per Architectural drawing ,design and specifications, complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
123	Providing and fixing vitreous china flat back range of three half stall urinal Large flat back no 5001 of size 63.3x39.5x42 cm (sixty three decimal three into thirty nine decimal five into forty two centimetre) with automatic flushing cistern of make Cera or its equivalent in white shade with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever require of snow white colour including connection with urinal and waste pipe by means of white lead mixed with chopped hemp (waste pipe to be measured and paid for separately) complete as per Architectural drawing ,design and specifications, complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
124	Providing and Fixing Charomium plated 40mm (forty millimetres) dia steel pipe for grab bars at 78cm (seventy eight centimetres) height metres M.S. plate as per details at the position of the seat and Wash Basin complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
125	Providing and fixing white vitreous china pedestal type Matrix water closet (European type) with seat and lid, 10 (ten) litre low level white vitreous china flushing cistern Hindware/Cera in white shade and as shown in the drawing / as per details & C.P. flush bend with fittings & C.I. brackets, 40 mm (forty millimetre) flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid including carriage of material within all leads, lifts and other. incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
126	Providing and fixing wash basin White Vitreous China Flat back Matrix wash basin 550x 400 mm (five hundred fifty into four hundred millimetre) of Hindware/Cera in white shade with single 15 mm (fifteen millimetre) C.P. brass pillar tap with C.I. brackets, 15 mm (fifteen millimetre) C.P. brass pillar taps, 32 mm (thirty two millimetre) C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require including carriage of material within all leads, lifts and other. incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
127	Providing and fixing stainless steel kitchen sink With drain board of Diamond or its equivalent big size 610x510 x 200mm (six hundred ten into five hundred ten into two hundred millimeters) of approved make with drain board and C.P waste with C.I or M.S brackets painted white including cutting holes in walls and making good the same complete including carriage of material within all leads, lifts and other. incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
128	Providing and fixing 32mm (Thirty two millimeter) nominal size diameters M.I. union for wash basin or sink including necessary fitting complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.
129	Providing and fixing 15mm (Fifteen millimetres) nominal bore P.V.C. connection pipe with brass union 45cm (Forty five Centimeters) length complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
130	Providing and fixing Mixer for kitchen sink with casted swinging spout at top Continental series of Jaquar / Classik series of Hindware /Floral series of Cera / Vintag series of Kerovite & Hindon series of Jal complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
131	Providing and fixing 32mm (thirty two millimeters) nominal diameters C.P waste for wash basin or sink complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
132	Providing and fixing two hole basin mixing Faucet of Continental series of Jaquar / Classik series of Hindware /Floral series of Cera / Vintag series of Kerovite & Hindon series of Jal complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
133	Providing and fixing 100mm (One hundred millimetres) C.P. iron grating of Superior quality of Continental series of Jaquar / Classik series of Hindware /Floral series of Cera / Vintag series of Kerovite & Hindon series of Jal for gully trap complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
134	Providing and fixing 75mm (seventy five millimetres) C.P. iron grating of Superior quality of Continental series of Jaquar / Classik series of Hindware /Floral series of Cera / Vintag series of Kerovite & Hindon series of Jal for gully trap complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
135	Providing and fixing 600x450mm (Six hundred into Four hundred fifty millimetre) nominal size bevelled edge mirror or superior glass of Modiguard/Saint Gobian mounted on 6mm (Six millimetre) thick A.C. sheet or ply wood sheet and fixed to wooden plugs with C.P. brass screws and washers including necessary fitting complete including carriage of material within all leads, lifts and other incidentals as per approved specifications, drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
136	Providing and fixing 600x20mm (Six hundred into twenty millimetres) size CP Brass towel rail of Continental series of Jaquar / Classik series of Hindware /Floral series of Cera / Vintag series of Kerovite & Hindon series of Jal complete with C.P. Brass brackets fixed to wooden plugs including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
137	Providing and fixing Plastic Liquid soap container with C.P. brass lid and brackets fixed to wooden plugs with C.P. brass screws complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
138	Providing and fixing C.P. Brass toilet paper holder (Heavy duty make ISI marked No. 8931 & 8934) complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
139	Providing and fixing 8mm (Eight millimetre) diametre C.P./S.S. Jet of Continental series of Jaquar / Classik series of Hindware /Floral series of Cera / Vintag series of Kerovite & Hindon series of Jal with flexible tube upto 1 (one) metre long with S.S. triangular plate to Eureopean type W.C. of approved quality complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
140	Providing and fixing 600x120 mm (Six hundred into One hundred twenty millimetre) nominal size glass shelf with C.P. brass brackets and guard rail complete fixed to wooden plugs with C.P. brass screws complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
141	Providing and fixing 15mm (Fifteen millimetre) diameters C.P. brass. Bib tap of Continental series of Jaquar / Classik series of Hindware /Floral series of Cera / Vintag series of Kerovite & Hindon series of Jal of approved quality (superior or heavy type) and colour complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
142	Providing and fixing 15mm (Fifteen millimetre) diameters C.P. brass. stop cock of Continental series of Jaquar / Classik series of Hindware /Floral series of Cera / Vintag series of Kerovite & Hindon series of Jal of approved quality (superior or heavy type) and colour complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
143	Providing and fixing 15mm (Fifteen millimetres) nominal bore/diametre brass angle valve of Continental series of Jaquar / Classik series of Hindware /Floral series of Cera / Vintag series of Kerovite & Hindon series of Jal without nut and pipe complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
144	Providing and fixing 15 mm nominal bore, CP, push cock of Continental series of Jaquar / Classik series of Hindware /Floral series of Cera / Vintag series of Kerovite & Hindon series of Jal without nuts and pipe complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
145	Providing and fixing 15mm (Fifteen millimetres) nominal bore/diametre brass full way valve with wheel of Continental series of Jaquar / Classik series of Hindware /Floral series of Cera / Vintag series of Kerovite & Hindon series of Jal complete in all respect including entire carriage of material within all leads, lifts and other incidentals, as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
146	Providing and fixing 15mm (Fifteen millimetres) nominal bore brass valve (Horizontal plunger) type high pressure with copper plate of Continental series of Jaquar / Classik series of Hindware /Floral series of Cera / Vintag series of Kerovite & Hindon series of Jal complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
147	Providing and fixing 110mm (One hundred ten millimetre) Nominal bore/diameters PVC single equal branch with oval access door, insertion rubber washer 3mm (Three millimetre) thick bolts and nuts ISI marked complete including fixing with approved adhesive etcetera complete in all floor level/height including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
148	Providing and fixing 75mm (Seventy five millimetre) Nominal bore/diameters PVC single equal equal branch with oval access door, insertion rubber washer 3mm (Three millimetre) thick bolts and nuts ISI marked complete including fixing with approved adhesive etcetera complete in all floor level/height including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
149	Providing and fixing 110mm (One hundred ten millimetre) Nominal bore/diameters PVC double equal branch with oval access door, insertion rubber washer 3mm (Three millimetre) thick bolts and nuts ISI marked complete including fixing with approved adhesive etcetera complete in all floor level/height including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
150	Providing and fixing 75mm (Seventy five millimetre) Nominal bore/diameters PVC double equal branch with oval access door, insertion rubber washer 3mm (Three millimetre) thick bolts and nuts ISI marked complete including fixing with approved adhesive etcetera complete in all floor level/height including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
151	Providing and fixing 110mm (One hundred ten millimetre) Nominal bore/diameters PVC door bend with oval access door, insertion rubber washer 3mm (Three millimetre) thick bolts and nuts ISI marked complete including fixng with approved adhesive etcetera complete in all floor level/height including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
152	Providing and fixing 75mm (Seventy five millimetre) Nominal bore/diameters PVC door bend with oval access door, insertion rubber washer 3mm (Three millimetre) thick bolts and nuts ISI marked complete including fixng with approved adhesive etcetera complete in all floor level/height including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
153	Providing and fixing 110mm (One hundred ten millimetre) Nominal bore/diameters PVC offset 45° (forty five degree) ISI marked of Finolex / Relpipe (Relience) / Vectus including fixing with approved adhesive etcetra complete in all floor level/height including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
154	Providing and fixing 75mm (Seventy five millimetre) Nominal bore/diameters PVC offset 45° (forty five degree) ISI marked of Finolex / Relpipe (Relience) / Vectus including fixing with approved adhesive etcetra complete in all floor level/height including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge.The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
155	Providing and placing on terrace (at all floor levels) polyethylene water storage tank having tripple layer of Finolex / Relpipe (Relience) / Vectus IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank complete in all respect including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
156	Providing and laying cement concrete 1:5:10 (One cement : Five sand : Ten graded stone agg. 40mm (Forty millimetre) nominal size bedding for 150 mm ( One hundred fifty millimetre) diametre PVC pipe with necessary form work and curing complete including necessary fitting complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
157	Constructing brick masonry manhole in cement mortar 1:4 (One cement isto four coarse sand ) with R.C.C. top slab with 1:1.5:3 mix {One cement isto One point five coarse sand (zone- III) isto Three graded stone aggregate 20 mm ( Twenty Millimeter) nominal size, foundation concrete 1:4:8 mix (One cement isto Four coarse sand (zone- III) isto Eight graded stone aggregate 40 mm ( Forty Millimeter) nominal size), inside plastering 12 mm ( Twelve Millimeter) thick with cement mortar 1:3 (One cement isto Three coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (One cement isto Two coarse sand isto four graded stone aggregate 20 mm ( Twenty Millimeter) nominal size) finished with a floating coat of neat cement complete as per standard design Inside size 90x80 cm ( Ninety into Eighty Centimeter) and 45 cm ( Forty Five Centimeter) deep including C.I. cover with frame (light duty) 455x610 mm ( Four Hundred Fifty Five into Six Hundred Ten Millimeter) internal dimensions, total weight of cover and frame to be not less than 38 kg ( Thirty Eight Kilogramme) {weight of cover 23 kg ( twenty Three Kilogramme and weight of frame 15 kg ( Fifteen Kilogramme} With Sewer bricks conforming to IS : 4885 complete as per the direction of Engineer-in-Charge icluding carriage of materials with in all leads , lifts and other incidentals. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
158	Constructing brick masonry manhole in cement mortar 1:4 ( one cement isto four coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (one cement isto one decimal five coarse sand (zone- III) isto three graded stone aggregate 20 mm ( twenty milimetres) nominal size), foundation concrete 1:4:8 mix (one cement isto four coarse sand (zone- III) isto eight graded stone aggregate 40 mm ( forty milimetres) nominal size), inside plastering 12 mm ( twelve milimetres) thickness with cement mortar 1:3 (one cement isto three coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (one cement isto two coarse sand isto four graded stone aggregate 20 mm ( twenty milimetres) nominal size) finished with a floating coat of neat cement complete as per standard design Inside Inside size 120x90 cm ( One hundred twenty into ninety centimetre) and 90 cm (ninety centimetre) deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg) deep including C.I. cover with frame (light duty) 455x610 mm ( four hundred fifty five into six hundred ten milimetres) internal dimensions, total weight of cover and frame to be not less than 38 kg ( thirty eight kilogram) (weight of cover 23 kg ( twenty three kilogram )and weight of frame 15 kg ( fifteen kilogram) With Sewer bricks conforming to IS : 4885 as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
159	Construction of brick masonry chambers for under ground C.I. inspection chamber and bends with second class common burnt clay building bricks in cement mortar 1:5 (one cement; five sand) C.I. cover with frame (light duty) 350mm x 610mm( three hundred fifty five millimeter into six hundred ten millimeter) internal diamensions total weight of cover and frame to be not less than 38 kg (thirty eight kilogramme) (weight of cover 23kg (twenty three kilogramme) and weight of frame 15 kg (fifteen kilogramme) with RCC top slab in cement concrete 1:2:4 ( one cement isto two sand isto four graded stone aggregate 20mm (twenty millimeter) nominal size) foundation concrete 1:5:10 ( one cement isto five sand isto ten graded stone aggregate 40mm (forty millimeter) nominal size) inside plaster 15mm(fifteen millimeter) thick with cement mortar 1:3 ( one cement isto three sand ) finished smooth with a floating coat of neat cement on walls and bed concrete inside dimensions 455x610x450mm( four hundred fifty five into six hundred ten into four hundred fifty millimeter) deep single pipe line complete as per HPPWD specifications or as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
160	Providing and fixing 600mmx300mm (six hundred into three hundred millimetre) vitreous china division plate for urinals of Hindware /cera/Jaquar of star white / snow white shade within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
161	Providing and laying 20 mm (twenty millimetre) nominal bore in trenches, galvanised mild steel tubes (medium grade) with G.I fittings including trenching and refilling etcetra including necessary fitting complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
162	Providing and fixing 15mm (fifteen millimetre) diametre to wall ceiling and floor galvanised mild steel tubes (Medium grade) tube fitting and clamps including making good the wall, ceiling and floor complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government. .
163	Providing and laying 150mm (One hundred fifty millimetres) nominal bore/diametres to level or slopes PVC pipe of Finolex / Relpipe (Relience) / Vectus for sewerage line and jointing with approved adhesive complete including carriage of material within all leads, lifts and other. incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge.The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
164	Supplying and fixing cast iron cover with rectangle frame 455 x 610 mm (four hundred fifty five into six hundred ten millimetre) (light duty) single seal pattern having weight not less than 23 kg (twenty three kilogram) as per HPPWD specifications within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
165	Providing and fixing 1.00 HP (one horse power) water lifting pump ISI marked of Kirloskar / Cromption including accessories and making necessery connection as required at site for its functioning complete as per HPPWD specifications within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government.
166	Providing 20x20 mm (twenty into twenty millimetre) square bar M.S Foot rest including fixing in man holes with 20x20x10 Cm (twenty into twenty into ten centimetre) cement concrete 1:3:6 (one cement isto three sand isto six graded /crushed stone aggregate) 20 mm (twenty millimetre) nominal size as per standard design within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is excluding GST, but including octroi, royality, Malkhana, toll tax, and any other taxes imposed by the Government. Please Enable Macros to View BoQ information

Tender Documents

SR No	FileName	File Description
1	Click here to download tender document	Tender Documents
2	Click here to download tender document	Tender Documents
3	Click here to download tender document	Tender Documents
4	Click here to download tender document	Tender Documents

Also Visit

Tenders

Himachal Pradesh Tenders

Construction Tenders

Building Construction Tenders

Building Work Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Construction Of Govt. Senior Secondary School At Kiar Koti, District Shimla (Hp). (Sh:- Construction Of Building Portion Including Water Supply & Sanitary Installation, Septic Tank And Rain Water Harvesting System., Shimla-Himachal Pradesh

Tender Documents

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Construction Of Govt. Senior Secondary School At Kiar Koti, District Shimla (Hp). (Sh:- Construction Of Building Portion Including Water Supply & Sanitary Installation, Septic Tank And Rain Water Harvesting System., Shimla-Himachal Pradesh

Tender Documents

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us