|
| 1 | Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing, spreading or stacking the spoils within a lead of 75 m. as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete. Depth of excavation not exceeding 1,500 mm. 250mm. Thik. Wall |
| 2 | Earth work in filling in foundation trenches or plinth with good earth, in layers not exceeding 150 mm. including watering and ramming etc. layer by layer complete. (Payment to be made on the basis of measurement of finished quantity of work). With earth obtained from excavation of foundation |
| 3 | With earth obtained by fresh excavation (includingcost of excavation upto 1,800 mm. depth) from landarranged by the Deptt. within a lead of 100 m. |
| 4 | Filling in foundation or plinth by silver sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation with water, ramming complete including the cost of supply of sand. (payment to be made on measurement of finished quantity) |
| 5 | Turfing with SodsFurnishing and laying of the live sods of perennial turfforming grass on embankment slope, verges or otherlocations shown on the drawing or as directed by theEngineer including preparation of ground, fetching ofsods and watering as per Clause 307 of Specificationsfor Road & Bridge Works of MoRT&H (5th Revision). |
| 6 | Single brick flat soling of picked jhama brick including ramming and dressing bed to proper level and filling joints with powdered earth or local sand. |
| 7 | Supplying and laying Polythene Sheet (150gm / sq.m.) over damp proof course or below flooring or roof terracing or in foundation or in foundation trenches. |
| 8 | Pre-Constructional Anti-termite measures:(a) Anti termite treatment to bottom surface ( in caseof masonry foundation and basements) and the sides(upto a height of 300 mm. from bottom) of theexcavation trenches with chemical emulsion byadmixing chloropyrofos emulsifiable concentrates (1%concentration) with water by weight at the rate of 5Litres per sq. m. area. The work shall be carried outas per specification described in 6.2.1. of code IS-6313 (part -II) 1981. (Mode of measurment will bethe plan area of foundation treated.) |
| 9 | Cement concrete with graded stone ballast (40 mm size excluding shuttering) In ground floor(A) [Pakur Variety] (b) 1:4:8 proportion |
| 10 | (a) 1:3:4 proportion |
| 11 | Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes. River bazree. |
| 12 | Hire and labour charge for shuttering with centreing and necessary staging upto 4 m. using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, columns, lintels curved or staight including fitting fixing and striking out after complection of works. (upto roof of ground floor) 25 mm to 30 mm shuttering without staging in foundation. 25 mm. to 30 mm. thick wooden shuttering as per decission & direction of E-I-C |
| 13 | Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc. including supply of rods, initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at inter-section, complete as per drawing and direction. for works in foundation,basement and upto roof of ground floor / upto 4.0m. i. Tor steel / Mild steel |
| 14 | Brick work with 1st class bricks in cement mortar (4:1) In foundation and plinth |
| 15 | Brick work with 1st class bricks in cement mortar (1:4) In superstructure, ground floor |
| 16 | 125 mm. thick brick work with 1st class bricks in cement mortar (4:1) in ground floor. |
| 17 | 75 mm. thick brick work with 1st class bricks in cement mortar (4:1) in ground floor including H.B. hetting in every alternate layer. |
| 18 | 25mm. thick damp proof course with cement concrete with stone chips (1:1.5:3) [with graded stone aggregate 10 mm nominal size] and admixture of water proofing compound as per manufacturer's specification followed by two coat of polymer based paint, (1st coat after 4 to 5 days of concrete laying and 2 nd coat just before brick masonry work) as directed (cost of water proofing compound & polymer based paint to be paid separately).( Chequering not required over concrete or painted surface). [Note: - Waterproofing as per item NO 60, polymer based paint as per item 59 (a) of Section (C). |
| 19 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface] With sand cement mortar (1:6) 20mm thick |
| 20 | With sand cement mortar (1:6) 15mm thick |
| 21 | With sand cement mortar (1:4) 10mm thick |
| 22 | Labour for Chipping of concrete surface before taking upPlastering work.-10mm thick |
| 23 | Artificial stone in floor, dado, staircase etc with cement concrete (1:2:4) with stone chips, laid in panels as directed with topping made with ordinary or white cement (as necessary) and marble dust in proportion (1:2) including smooth finishing and rounding off corners including raking out joints or roughening of concrete surface and application of cement slurry before flooring works using cement @ 1.75 kg/sq.m all complete including all materials and labour. In ground floor. 3 mm. thick topping (High polishing grinding on this item is not permitted with ordinary cement). Using grey cement . 25 mm. thick |
| 24 | Neat cement punning about 1.5mm thick in wall,dado,window sill,floor etc. |
| 25 | Wood work in door and window frame fitted and fixed complete including a protective coat of painting at the contact surface of the frame. (The quantum should be corrected upto three decimals) sal :- malasian |
| 26 | Panel shutters of door and window, as per design (each panel consisting of single plank without joint), including fitting and fixing the same in position but excluding the cost of hinge and other fittings. In ground floor. (In case of non-supply of single plank, penal rate of reduction of 20% will be made) (i) 50mm thick shutters with 25mm thick panel of size 30 to 45 cm(b) Sishu, Gamar, Champ,Badam,Bhola, Mogra, Hallak. 35mm thick shutters with 19mm thick panel of size 30 to 45 cm. (a) Ordinary Teak Wood. |
| 27 | Supplying, Fitting & Fixing Factory made P.V.C. door frame of size 50 mmx47 mm with a wall thickness of 5 mm, made out of extruded 5 mm, PVC sheet miter cut at twocorners and joined with two nos of 1.5 mm long brackets of 15 mm x15 mm M.S. square tube. The two vertical door profiles are to be reinforced with 19 mmx 19 mm M.S. Square tube of 19 gauge, weather seal to be provided through out the frame. The door frame shall be fixed with the wall using 65/100 mm long M.S. Screws through the frame by using P.V.C fasteners. A minimum of 4 Nos of screws to be provided for each vertical member and minimum 2 Nos for |
| 28 | Supplying, Fitting & Fixing 30 mm thick Factory made solid Panel PVC Door Shutter consisting of outer frame made out of M.S. tubes of 19 gauge thickness and size 19 mmx19 mm for styles, top and bottom rails, M.S. frame shall have cost of steel primers of approved make and manufacture, M.S. frame covered with 5 mm th. heat moulded PVC “C” channel of size 30 mm th, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on either sides forming styles; and 5 mm th. 95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm tapered in 45 degree on the inner side to form top & bottom rail and 115 mm wide PVC sheet out of which 75mm shall be flat and 20mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided either side of the panel with 10 mm (5 mmx2) th.,20 mm wide cross PVC sheet as gap insert for top rail and bottom rail. Paneling of 5 mm th. both side PVC sheet to be fitted in the M.S. frame welded/sealed to the styles &rails with 7 mm (5 mm+2 mm) th.x15 mm wide PVC sheet beading on inner side and joined together with solvent cement adhesive. An additional 5 mm th. PVC strip of 20 mm which is to be stuck on the interior side of the “C” channel using PVC solvent adhesive etc. complete excluding all necessary hardwares as per direction of Engineer-in-Charge.In ground floor |
| 29 | M.S.or W.I. Ornamental grill of approved design joints continuously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugs in ground floor. (i) Grill weighing above 10 Kg./sq.mtr and up to 16 Kg./sq. mtr. |
| 30 | M.S. clamp for fixing door and window frame made of flat bent bar, end bifurcated, fixed in cement concrete with stone chips (4:2:1) fitted and fixed complete as per direction.( 40mm x 6mm. 200mm length) |
| 31 | Iron butt hinges of approved quality fitted fixed with steel screws,with ISI mark (100 mm x 75mm. X 3.5mm) |
| 32 | Anodised aluminium barrel / tower / socket bolt (full covered) of approved manufactured from extruded section conforming to I.S. 204/74 fitted and fixedwith cadmium plated screws:(i) 300mm long x 10mm dia. bolt. |
| 33 | Anodised aluminium Aldrop / Sliding bolts of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 2681/66) fitted andfixed complete.(i) 250mm x 16mm dia bolt. |
| 34 | Anodised aliminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 230/72) fitted and fixed complete:(a) With continuous plate base (Hexagonal/ Round rod)(i) 75 mm grip x 10 mm dia rod. |
| 35 | 125mm long wooden buffer blockii) With Sal : Malayasian |
| 36 | Supplying, fitting and fixing UPVC pipes A- type and fittings conforming to IS 13592-1992with necessary clamps nails including making holes in walls etc and cutting trenches in any soil through masonry concrete structure etc. if necessary and mending good damages including jointing with joining materials( Spun yarn. valamoid/bitumen/ M. seal etc. ) complete. UPVC Pipes. 110 mm dia. |
| 37 | UPVC fittings shoe: 110mm |
| 38 | Bend 87.5 degree: 110mm |
| 39 | primimg one coat on steel or other metal surface with synthetic oil bound primer , steel wimndow |
| 40 | Priming one coat on timber, plastered or on steel or other metal surface with synthetic enamel/oil bound prinmer of approved quality including smoothening surfaces by sand papering etc. On steel or other metal surface: |
| 41 | (A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand parpering etc. in cluding using of approved putty etc. on the surface , if necessary. On steel or other metal surface: With super gloss (hi-gloss) one coats (except white in shade ) |
| 42 | On steel or other metal surface: With super gloss (hi-gloss) Two coats (except white in shade ) |
| 43 | White washing including cleaning and smoothening surface thoroughly. Three coats (on new works only). |
| 44 | Applying decorative cement based paint of approved quality after preparing the surface including scraping the same thoroughly (plastered or concrete surface) as per manufacturer's specification. Two coats . |
| 45 | Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc. FloorWith Sand Cement Mortar (1:4) 20 mm thick & 2 mm thickcement slurry at back side of tiles using cement @ 2.91Kg/Sq.m & joint filling using white cement slurry @0.20kg/Sq.m.(a) Area of each tile upto 0.09 Sq.m(i) Coloured decorative |
| 46 | Precast pierced concrete jally work as per design and manufacturer's specification including moulding etc. with stone chips and necessary reinforcement shuttering complete including fitting, fixing in position in all floors.(a) 37.5 mm. thick panels |
| 47 | Supplying and laying chequered tiles of any shade & ofapproved quality with (1:1½:3) cement concrete laid in panels or patterns as directed in pavement, footpath etc. including necessary underlay 25 mm thick [avg] cement mortar (1:3) complete in all respect with all labour and materials. [Using cement slurry @ 4.4 kg/Sq.m at back side and @2.4 kg/Sq.m for joint filling] Red Variety(i) 25 mm. thick |
| 48 | Galvanised Iron pipe outer for water with bevelied end at outet. Supplied fitting and fixing complete including two coats to the exposed portion. 40 mm dia. |
| 49 | Hire and labour charges for 75 mm dia bamboo railing onJhau/Eucalyptus or other approved timber posts 1.4 m above G.L. and 0.60 m below G. including tying strongly with coir ropes and boring holes for posts in any soil/ concrete surface/Bituminious surface packing the sides etc including cost of carriage of all materials and labour complete including cost of restoration to the damages of the ground to its original condition as per direction of Engineer in charge after removing the barricade. (Cost of restoration would be paid separately.) |
| 50 | SANITARY AND PLUMBING WORKS:- Construction of septic tank of different capacities as per approved drawing with 1st class brick work in cement mortar (1:4) including two 560 mm dia. R.C.C. manhole cover(heavy type)of approved make supplied, fitted and fixed in the 100mm thick R.C.C (1:1.5:3) top slab with necessary fittings, 20mm thick cement plaster (4 : 1) with neat cement finish to the internal surfaces and 15 mm thick cement plaster (4 : 1) to outside wall upto 200 mm below G.L floor finished with 25 mm thick grey artificial stone over 100 mm thick R.C.C(1:1.5:3) bottom slab including supplying, fitting and fixing all necessry specials, fittings, S.W. tees, C.I. foot rest etc. including excavation earth in all sorts of soil, shoring, bailing out and pumping out water as necessary, ramming, dressing the bed and fefilling the sides of the tanks with earth, removing spoils, filling up the chamber with clear water, removing foreign materials from the chamber and including constructing attached inspection pit as per approved drawing and connecting all necessary pipes, joints etc. with internal plaster work and artificial stone flooring is to be done with admixture of water proofing compound @ 0.5% by weight of cement with all costs of labour and materials. (iv) For 10 users. B) With River Bazree(N.B Varity |
| 51 | Supplying P.V.C. water storage tank of approved quality with closed top with lid (Black) - Multilayer (a) 500 litre capacity |
| 52 | Labour for hoisting plastic water storage tank.(i) Upto 1500 litre capacity.(a) Upto 1st story from G.L |
| 53 | Labour for punching hole in plastic water storage tank upto 50 mm dia. |
| 54 | Supplying, fitting and fixing bib cock or stop cock.(ii)polythene Bib Cock long body with wall flange with aerator ...15 mm |
| 55 | Supplying, fitting and fixing CPVC (ChlorinatedPolyvinyl Chloride) pipes of approved make conformingto IS-15778: 2007 . with all necessary accessories,specials viz. socket, bend, tee, union, cross, elbo, nipple,longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials.(a) For Exposed Work- 15 mm dia |
| 56 | 25 mm dia |
| 57 | 32 mm dia |
| 58 | Supplying, fitting and fixing Orissa pattern water closet in white glazed vitreous chinaware of approved make in position complete excluding 'P' or 'S' trap (excluding cost of concrete for fixing). (i) 530 mm X 410 mm |
| 59 | Supplying, fitting & fixing Cast iron soil pipe only conforming to I.S. 3989/ 2009 and I.S. 1729/2002 with bobbins, nails etc. including making holes in the wall, floor etc. and cutting trenches etc. in any floor through masonry concrete, if necessary, and mending good damages with necessary jointing materials and painting two coats to the exposed surface with approved paint complete. (Measurement will be made along the center line of the total pipe line in fitted condition including specials,payment for specials & Painting will however be paid seperately).(a) With valamoid joints including sealing with sand cement morter (4:1) upto quarter depth.(i) 100 mm dia. (internal) |
| 60 | Supplying,fitting and fixing cast iron 'P' or 'S' trap conformimg to I.S. 3989 / 1970 and 1729 / 1964 including lead caulked joints and painting two coats to the exposed surface. (Painting to be paid seperately).(A) 'S' Trap (i) 100 mm |
| 61 | Buster pump for uplifting water from hand tube well to over head storage tank |
| 62 | Supplying, fitting and fixing check valve (vertical ) G.M. Tested to 21 kg per sq.cm |
| 63 | Supplying, fitting and fixing gunmetal wheel valve of approved brand and make tested to 21 kg per sq. cm. (for water lines only).(vii) 40 mm dia |
| 64 | HAND TUBE WELL : Labour for boring tube well of required dia. by water jet system through any type of soil strata including hire and labour charges for boring pipes, scaffolding, tools and plants as necessary and taking out them and lowering pipes, strainers, blind pipe etc. and fitting and fixing the same complete including bucket washing and other incidental works in the connection. The tube well should have a minimum 50 mm gap in between the outside of the tubewell pipe and the bore.a) for depth up to 150.00m. (i)40 mm dia. boring etc |
| 65 | Supply of G.I. pipes of TATA make including necessary sockets.e) 40 mm dia. i) Medium quality |
| 66 | Supply of PVC pipes & fittings (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). (Dia) 40 mm. Elbow. (Bansal) |
| 67 | Supplying pvs strainer of approved make adapter conforming to IS. 12818 specification.i) 40 mm dia. |
| 68 | Supplying, fitting and fixing plug of approved make adapter conforming to IS. specification.i) 40 mm dia. |
| 69 | Supplying, fitting and fixing steel cutter piece upto 450 mm long with sockets. i) 40 mm dia. |
| 70 | Collecting sample of water for bacteriological and chemical test from any depth at any time during execution of work including hire and labour charges for tools and plants and sterilising the equipments, paying all charges and fees, testing etc. complete in all respect as per direction. |
| 71 | Geophysical investigation of the acquifer by electrologging system with all tools and plants as necessary including supply of necessary report |
| 72 | Supplying, fitting and fixing popular maya pump no. 6 or similar.i) for 40 mm dia. tube well |
| 73 | Brick work with 1st class bricks in cement mortar (4:1) In foundation and plinth |
| 74 | Single brick flat soling of picked jhama brick including ramming and dressing bed to proper level and filling joints with powdered earth or local sand. |
| 75 | Cement concrete with graded stone ballast (40 mm size excluding shuttering) In ground floor(A) [Pakur Variety] (b) 1:4:8 proportion |
| 76 | Artificial stone in floor,dado, staircase etc. with cement conctrete (4:2:1) with stone chips laid in panels as directed with topping made with ordinary or white cement (as necessary) and marble dust in proportion (2:1) including smooth finishing and rounding off corners and including application of cement slurry before flooring works, using cement @ 1.75 kg./sq.m. all complete including all materials and labour. \In ground floor. 3 mm. thick topping (High polishing grinding on this item is not permitted) with ordinary cement.25 mm. thick |
| 77 | ADD GST @ 18% |
| 78 | ADD LABOUR WELFARE CESS @ 1% |
| 79 | ADD ELECTRIFICATION INCLUDING SUPPLY OF ELECTRIC GOODS AND 18% GST AND 1% LWC AND INCLUDING ALL. ITEM DETAILES IN THE DETAILED ESTIMATE Please Enable Macros to View BoQ information |
