|
| 1 | Excavation in drains and channels etc. in earth work in all kinds of soil such as pick jumper work, blasting work and hard blasting work saturated soil including chiselling where blasting is not possible or any other mixed variety of soil dewatering and removal of slush and other incidentials lift upto any height stacking the excavated soil upto any lead from the edge of excavation and then returning the stacked soil in 15cm (Fifteen centimetre) thick layer when required into plinths si des of foundations etc. consolidating each deposited layer by ramming and watering and then disposing of al surplus excavated earth with in all leads and lift, of materials and as per direction of Engineer-in-charge. |
| 2 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:5:10 (1 cement : 5 coarse sand): 10graded stone aggregate 40 mm (Forty millimetre) nominal size) within all leads and lift of materials and as per direction directions of Engineer in charge. |
| 3 | Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm (Twenty millimetre) nominal size) upto plinth level : Cement mortar 1:6 (1 cement : 6 coarse sand) Random rubble masonry with hard stone in superstructure above plinth level and upto floor five level, including leveling up with cement conrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm (Twenty millimetre) nominal size) at window sills, ceiling level and the like with with in all leads and lift of materials and as per direction of Engineer-in-charge. |
| 4 | Providing form work with steel plates 3.15mm(Three point fifteen milimetre) thick welded with angle iron in frame 30x30x5mm(Thirty x thirty x five milimetre). so as to give a fair finish including centring, shuutering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 Mtrs. and removal of the same for insitu-reinforced concrete & plain concrete work in:Flat surfaces such as soffits of suspended floors, roofs, landings and the like.Floors etc.upto 200mm. in thickness with in all leads and lift of materials and as per direction of Engineer-in-charge. |
| 5 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm (Five millimetre)), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge)within all leads and lift of materials and as per direction directions of Engineer in charge. |
| 6 | Providing mild steel/Tor steel reinforcement for R.C.C. work including bending, binding and placing in position complete upto floor two level Mild steel with in all leads and lift of materials and as per direction of Engineer-in-charge. |
| 7 | Brick work using common burnt clay building bricks in superstructure above plinth level up to floor any level in second class bricks all shapes and sizes in Cement mortar 1:6 (One cement : Six coarse sand) including carriage of materials with in all leads and lift, of materials and as per direction of Engineer-in-charge. |
| 8 | Half brick masonry with common burnt clay building bricks in cement mortar 1:3 (1 cement : 3 coarse sand) second class bricks in superstructure above plinth level up to floor V level. with in all leads and lift of materials and as per direction of Engineer-in-charge. |
| 9 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).In second class Deodaar wood with in all lifts and lead of materials and as per direction of Engineer -In-Charge. |
| 10 | Providing 40x5 mm (Forty x Five millimetre) flat iron hold fast 40 cm (Forty centimetre) long including fixing to frame with 10 mm (Ten millimetre) diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm (Thirty x Ten x Fifteen centimetre) 1:3:6 mix (1 cement : 3 coarse sand :6 graded stone aggregate 20mm (Twenty millimetre) nominal size). within all leads and lift of materials and as per direction of Engineer-in-charge. |
| 11 | Providing and fixing 0.60mm (Zero point sixty millimetre) thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyester (RNP) organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating to back coat of polyester 5 (Five) microns over 5 (Five) microns primer coating including fixing with screws, prepainted iron J or L hooks bolts and nuts 6mm (Six millimetre) diameter with pre-painted limpet and rubber washers complete with all accessories as required within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge. |
| 12 | Providing and fixing ridges or hips 60 cm over all with 0.60 mm (Zero point sixty millimetre) thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6 mm (Six millimetre) dia metre with prepainted limpet and rubber washers complete with all accesories as required within all leads and lift and carriage of material in all respect as per direction of Engineer-in- charge. |
| 13 | Providing and fixing 15 cm (Fifteen centimetre) wide, 45 cm (Forty five centimetre) overall semi-circular 0.60 mm (Zero point sixty millimetre) steel sheet gutter with prepainted iron J or L hooks, bolts & nuts 6 mm (Six millimetre) dia & prepainted G.I. limpet and bitumen washers complete with in all leads and lift of materials and as per direction of Engineer-in-charge. |
| 14 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm (Twenty centimetre) any depth, consolidating each deposited layer by ramming and watering, upto any lead and lift within all leads and lift of materials and as per direction of Engineer-in- charge. |
| 15 | Boulder filling of selected hard dry stone hand packed tightly under floor including carriage of materials with in all leads and lift of materials and as per direction of Engineer-in-charge. |
| 16 | Walls (any thickness) including attached plasters, butteresses, plinth and string course etc. within all leads and lifts including carriage of materials in all respect and as per direction of Engineer-in-charge. |
| 17 | Providing and laying reinforced cement concrete design mix M-25 grade mechanically mixed and vibrated and curing complete excluding cost of form work and reinforcement for reinforced cement concrete work in foundation footings bases of columns and the like and mass concrete complete within all leads and lift of materials and as per direction directions of Engineer in charge. |
| 18 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more with in all leads and lift of materials and as per direction of Engineer-in-charge. |
| 19 | Providing and laying spartic ceremic tiles 5.5mm(Five point five millimetre) thick in flooring (300 x300mm(Three hundred x Three hundred millimetre) size)treads of steps laid on a bed of 12mm(Twelve millimetre) thick cement mortar 1:3(1cement: 3 sand) finished with Flash pointing in white cement with in all leads and lift of materials and as per direction of Engineer-in-charge. |
| 20 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.with in all leads and lift of materials and as per direction of Engineer-in-charge. |
| 21 | 15mm (fifteen millimetre) Cement plaster in single coat on the rough side of brick/ concrete/stone walls for interior plastering upto floor two level including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm(eighty millimetre) in girth and finished even and smooth.Cement Mortar 1:6(one cement : six sand) with in all leads and lift of materials and as per direction of Engineer-in-charge. |
| 22 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete Fixed to openings /wooden frames with rawl plugs screws etc. with in all leads and lift of materials and as per direction of Engineer-in-charge. |
| 23 | Steel work welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete within all leads and lift of materials and as per direction of Engineer-in-charge. |
| 24 | Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete (Note:- Butt hinges and necessary screws shall be paid separately) 35 mm (Thirty five millimetre) thick shutters with in all leads and lift of materials and as per direction of Engineer-in-charge. |
| 25 | Providing and fixing wire gauge shutter using galvanised M.S. wire gauge of I.S. gauge designation 85G with wire of dia 0.56 mm (Zero point fifty six millimetre) for door window and clestory window including bright finished black enamelded iron hings with necessary screws 30 mm (Thirty millimetre) thick 2nd class deodar wood with in all leads and lift of materials and as per direction of Engineer-in-charge. |
| 26 | Providing and fixing anodised aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with bolts, nuts and screws etc. complete 300 X 16 mm (Three hundred x Sixteen millimetre) with in all leads and lift of materials and as per direction of Engineer-in-charge. |
| 27 | Providing and fixing aluminium tower bolts, (barrel type) ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete, 200x10 mm (Two hundred x Ten millimetre) with in all leads and lift of materials and as per direction of Engineer-in-charge. |
| 28 | Providing and fixing aluminium tower bolts, (barrel type) ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete, 150x10 mm (One hundred fifty x Ten millimetre) with in all leads and lift of materials and as per direction of Engineer-in-charge. |
| 29 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete 125 mm (One hundred twenty five millimeter) with in all leads and lift of materials and as per direction of Engineer-in-charge. |
| 30 | Providing and fixing insulating board ceiling of approved quality with necessary nails etc. complete (frame work to be paid separately) Natural colour insulating board 12 mm thick (Twelve millietre) within all leads and lift of materials and as per direction of Engineer-in-charge. |
| 31 | 50 mm (Fifty millimetre) thick cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) 20 mm (Twenty millimetre) size mechanically mixed laid in one layer finished with a floating coat of neat cement up to all floor level complete with in all leads and lift of materials and as per direction of Engineer-in-charge. |
| 32 | Finishing walls with water proofing cement paint of approved brand and manufacture and of required shade on undercorated wall surfaces (two coats) to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials including/ carriage of all labour equipements and materials to various locations through all mode of transport with in all leads and lift of materials and as per direction of Engineer-in-charge. |
| 33 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade New work (two or more coats) over and including water thinnable priming coat with cement primer with in all leads and lift of materials and as per direction of Engineer-in-charge. |
| 34 | Applying priming coat over new wood and wood based surfaces after and including prepering the surface by thoroughly cleaning oil,grease,dirt and other foreign matter) sand papering and knotting.Readymixed paint brushing with white lead for priming with in all leads and lift of materials and as per direction of Engineer-in-charge. |
| 35 | Painting two coats (excluding priming coat)on new steel and other metal surface under coat with ready mixed paint brusing to give an even shade including cleaning the surface all dirt,dust and other foreign matter :-- With white readymixed paint within all leads and lift of materials and as per direction of Engineer-in- charge. |
| 36 | Providing plinth protection 50 mm (Fifty millimetre) thick cement concrete 1:3:6 (One cement : Three sand : Six graded stone) aggregated 20 mm (Twenty millimetre) within all leads and lift of materials and as per direction of Engineer-in- charge. |
| 37 | Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS:15801, UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes the cost of cutting chases and making good the same including testing of joints complete within all leads and lift of materials and as per direction directions of Engineer in charge . |
| 38 | Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS:15801, UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes the cost of cutting chases and making good the same including testing of joints complete within all leads and lift of materials and as per direction directions of Engineer in charge . |
| 39 | Making connection of galvanized steel distribution branch with galvanized mild steel main 20 mm (Twenty millimetre) to 40 mm (Forty millimetre) nominal bore by providing and fixing Tee including cutting and trenching the pipe within all leads and lift of materials and as per direction directions of Engineer in charge . |
| 40 | Providing and fixing C.P. stop cock of approved quantity 15 mm (Fifteen millimeter) nominal bore within all leads and lift of materials and as per direction directions of Engineer in charge . |
| 41 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) 25 mm (Twenty five millimetre) nominal size within all leads and lift of materials and as per direction directions of Engineer in charge . |
| 42 | Constructing masonry Chamber 30x30x50 cm (Thirty x Thirty x Fifty centimetre) inside, in brick work in cement mortar 1:4 (1 cement : 4 coarsesand) for water meter complete with C.I. double flap surface box 100x100x75 mm (One hundred x One hundred x Seventy five millimetre) (inside) with locking arrangement and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm (Twenty millimetre) nominalsize) , i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand:10 graded stoneaggregate 40 mm (Forty millimetre) nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm (Twelve millimetre) thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 within all leads and lift and carriage of material in all respect as per direction of Engineer-in-charge. |
| 43 | Providing and fixing stainless steel kitchen sink of approved standard ISI make with drain board and C.P. waste with C.I. or M.S. Brackets painted white including cutting holes and making good the same but excluding fitting. 610 x460 mm(Six hundred ten x Four hundred sixty millimetre) with bowl depth 200 mm(Two hundred millimetre) with in all leads and lift of materials and as per direction of Engineer-in-charge. |
| 44 | Providing and fixing C.P. brass towel rail complete with C.P. brass brackets fixed to wooden plugs with C.P. Brass screws. 600 x 20 mm within all leads and lift of materials and as per direction of Engineer-in- charge. |
| 45 | Cutting chases in brick masonry walls for following diametre sand cast iron/centrifugally cst(spun) pipesand making good the same with cement concrete 1:3:6 (One cement : Three sand : Six graded stone) aggregated 12.5mm (Twelve point five millimetre) nominal size , including necessary plaster and pointing in cement mortar 1:4 (1 cement : 4 coarsesand) 100mm (One hundred millimetre) within all leads and lift of materials and as per direction of Engineer-in- charge. |
| 46 | Providing lead caulked joints to sand iron/centrifugally cast(spun) iron pipes and fittings of diametre 100mm (One hundred millimetre) within all leads and lift of materials and as per direction of Engineer-in- charge. |
| 47 | Providing lead caulked joints to sand cast iron/(spun) iron pipes and fittings of diametre 75mm (Seventy five millimetre) within all leads and lift of materials and as per direction of Engineer-in- charge. |
| 48 | Providing and fixing collar 100mm (One hundred millimetre) sand cast iron S&S as per IS-1729 within all leads and lift of materials and as per direction of Engineer-in- charge. |
| 49 | Providing and fixing door piece, insertion rubber washer 3mm (Three millimetre) thick, bolts and nuts complete door piece within all leads and lift of materials and as per direction of Engineer-in- charge. |
| 50 | Providing and fixing heel rest sanitary bend 100mm (One hundred millimetre) dia sand cast iron S&S as per IS:1729 within all leads and lift of materials and as per direction of Engineer-in-charge. |
| 51 | Providing and fixing 600x120 mm (Six hundred x One hundred twenty millimetre) glass shelf with C.P. brass bracket and guard rail shelf with C.P. brass bracket and guard rail complete, fixed to wooden plugs with C.P. brass screws with in all leads and lift of materials and as per direction of Engineer-in-charge. |
| 52 | Providing and fixing 600x450 mm (Six hundred x Four hundred fifty millimeter) bevelled edged mirror of superior glass (of approved quality) complete with 6 mm (Six millimeter) thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete within all leads and lift of materials and as per direction directions of Engineer in charge . |
| 53 | Providing and fixing wash basin with C.I. brackets, 15 mm (Fifteen millimeter) PTMT pillar cock, 32 mm (Thirty two millimeter) PTMT waste coupling of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Flat back wash basin size 550x 400 mm (Five hundred fifty x Four hundred millimeter) with ingle 15mm (Fifteen millimtere) PTMT pillar cock within all leads and lift of materials and as per direction directions of Engineer in charge . |
| 54 | Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre (Ten litre) low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm (Forty millimeter) flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required W.C. pan with ISI marked white solid plastic seat and lid within all leads and lift of materials and as per direction directions of Engineer in charge . |
| 55 | Providing and fixing PVC water storage tank of ISI marked, G.I. inlet and outlet connection, 15mm (Fifteen millimetre) nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting upto all heights above ground level 2000 litres (Two thousand litres) net capacity tank including hauling/carriage of all labour equipements and materials to various locations through all modes of transportation within all leads and lift of materials and as per direction directions of Engineer in charge . Please Enable Macros to View BoQ information |
