|
| 1 | Providing and fixing rolling shutter fabricated from steel laths of minimum thickness 0.9mm with lock plate of 3.15mm thickness reinforced with 35x35x5mm angle section fitted with sliding bolts and handles for both sides, deep M.S. channel section of depth and thickness not less than 65mm and 3.15mm respectively with hold fast arrangements, M.S. Bracket plate 300x300x3.15mm minimum size and shape with square bar, suspension shaft of minimum 32mm diameter, hood cover of M.S. sheet not less than 0.9mm thickness and of any size at top and safety devices including mechanical gear operation arrangement consisting of worm gear wheels and worms of high grade cast iron or mild steel and one coat of red lead primer etc.complete. (I.S.62481979)(With mechanical gear) |
| 2 | Providing and Fixing mat finish stainless steel (of 302 grade ) railing with top pipe of 50 mm dia. and vertical pipe of 38 mm dia at 0.60mc / coras required and horizontal pipes of 25mm dia in three rows, all pipes of 2mm thick including buffing, fabricating fixtures and fastening including pipe base of appropriate diameter and ball base of 75mm dia above newel post of 75mmdia meter etc.complete (Prior approval of sample and brand by Ex.Engineer is necessary before use) |
| 3 | Providing and fixing C.P. pillar cock long neck with aerator of approved make including necessary sockets/union nut etc. complete. |
| 4 | Providing and fixing C.P. wall mixer with provision for overhead shower with 115mm long bend pipe and wall flange of approved make including necessary sockets/union nut etc. complete. |
| 5 | Providing and fixing C.P.Two way BIB cock of approved make continental including necessary sockets/union nut etc. complete |
| 6 | Providing and fixing 15mm diameter PVC Aqua kraft type of approved make super jet spray with flange 2 in 1 faucet 1.50 metre long including all accessories etc complete |
| 7 | RWH- Shallow Percolation Pit providing, constructing 2.0m deep shallow depth percolation pit comprising of 1.0m dia pre-cast RCC rings, 300 mm thick side filling around outside of RCC rings (annular space) with 40mm size boulders including filling of percolation pit up to 0.5m depth (from bottom up) with 25-75mm clean washed gravels followed by 0.5m depth of 10-25mm of clean washed stones followed by 0.5m of washed river fine aggregate (natural sand/ crushed sand VSI grade finely washed etc.) including netlon mesh between each gravel/ fine aggregate (natural sand/ crushed sand VSI grade finely washed etc.) media layer including covering with RCC slab, manhole frame & cover, PVC rungs etc. including arrangement for inlet & outlet pipe, excavation & back filling as shown in the drawing. The rate shall be inclusive of all labour, material, wastage, scaffolding, transportation, taxes, including all leads, lifts at all levels. All material should be of approved make. All works complete as per the drawing, technical specification and direction of the Engineer in charge |
| 8 | Providing patti/ band 75mm wide on plastered surface 12 mm to 15 mm thick in C.M. 1:3 line and level including neat finishing scaffolding curing etc. complete. |
| 9 | Providing groove to required size at specified location as directed by Engineer, at junction of brick masonry wall and R.C.C beams or Column, at junction of composite masonry, including scaffolding, finishing, curing etc. complete |
| 10 | Providing and erecting Overhead signs made out of mm aluminum sheet bonded with white retro reflective sheeting of Class ( Type IV High intensity micro-prismatic grade sheeting-HIP) having pressure sensitive/heat activated adhesive retoreflective specified back ground, border and back side retoreflctive symbols, letters, numerals, arrow as per IRC:67-2012, with designed back support frame of mild steel angle with vertical and lateral clearance given in clause 801 and 802, duly painted on back side with two coats of grey stove enamel paint and installed as per clause 802.6 over a designed support system of structural steel work trestles and trusses of sections and type as per structural design requirements and approved plans including painting with one coat of epoxy primer and two coats of epoxy finish paint.The nut bolts of board with angle iron post/supporting structure after fixing at site has to be electrically welded. Class B ( Type IV High intensity micro-prismatic grade sheeting-HIP) sheeting shall have 7 years written warranty from the manufacturer and authorised distributor/convertor issued for field performance including the screen printed areas and cut-out sheeting and cut-out durable transparent overlay film and this warranty certificate in original should be submitted to the Engineer in charge by the contractor/supplier.This item does not include the cost of structural steel work required for support system. |
| 11 | 4mm aluminum composite material Class C |
| 12 | Providing and fixing of retro-reflectorised informatory sign boardrectangular/Square in shape having area greater than 0.9O ne Square Meter rmade out of ___mm aluminum sheet bonded with white retro reflective sheeting of Class__(TypeIVHighintensitymicro-prismatic grade sheeting-HIP)having pressure sensitive/heat activated adhesiveretor eflective specified background,borde rand back sideretor eflctive symbols,letters,numerals,arrowasper IRC:67-2012 Table No8.3 ,supported with back support frame 25mm x 25mm x 3mm ,duly painted on back side with two coat sofgreystove enamel paintand supported on two no.mild steel angle iron post 75mm x 75mm x 6mm,3.5mt long firmly fixed to the ground by means of properly designed foundation with M25grade cement concrete 45cmx45cmx60cm ,60 cm below ground level as per approved drawing The angle iron post shall be duly painted with one coat of epoxy primer and two coats of epoxy finish paint shaving alternate black and white bands of 25 cm width including GI fixures and transportation etc.complete.The nutbolt sofboard with angle iron post/supporting structure after fixing at site has to be electrically welded.ClassB(Type IV High intensity micro-prismatic grade sheeting-HIP)sheetingshallhave7yearswrittenwarrantyfromthemanufacturerandauthoriseddistributor/convertorissuedforfieldperformanceincludingthescreenprintedareasandcut-outsheetingandcut-outdurabletransparentoverlayfilmandthiswarrantycertificateinoriginalshouldbesubmitted to the Engineer in charge by the contractor/supplier.4mm aluminum composite material of Class B |
| 13 | 4mm aluminum composite material of Class B |
| 14 | Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 0.00 to 1.50 m.) By Manual Means |
| 15 | Providing and fixing factory made Hydraulically pressed Mechanically vibrated and compacted precast inter locking cement concrete paving blocks 80MM thick in M-40 grade of approved size and shape for City streets, small /medium market roads,low volume roads, utility cuts on arterial roads etc. as specified and as per IS 15658:2006 including cost of all materials, manufacturing, curing, transportation of blocks to work site including loading, unloading and stacking as directed, laying paving blocks in position over prepared bed of natural sand / crushed sand of 50 mm thickness including necessary excavation in all stratas, spreading blindge of fine sand over the prepared bed, compacting blocks by plate vibrator etc. complete. |
| 16 | Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 mm thick in cement mortar 1:4 using waterproofing compound at 1Kilogramper cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete. |
| 17 | Providing and applying two coats of exterior acraylic emulsion paint confirming to corresponding I.S.of approved manufacture and of approved colour to the plastered surfaces including cleaning, preparing the plaster surface, applying primer coat, scaffolding if necessary , and watering the surface for two days etc complete. |
| 18 | Providing and laying Cast in situ/Ready Mix cement concrete in M15 of trap/ granite/quartzite/gneiss metal for foundation and bedding / steps including steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface, only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.),with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) |
| 19 | Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap / granite/quartzite/ gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) |
| 20 | Providing dry / trap / granite / quartzite / gneiss rubble stone soling 15cm to 20cm thick including hand packing and compacting etc. complete. |
| 21 | (A) USAGE RATES OF PLANT AND MACHINERY FOR YEAR 2022-23 Other Allied Machinery |
| 22 | Truck Trailor 30 MT capacity |
| 23 | LABOUR RATES FOR PWD SSR 2022-23 FOR YEAR 2022-23 |
| 24 | Mazdoor - Unskilled Heavy Male |
| 25 | (b) Add for moulding & polishing edges in item no. Bd / A / 23 (a) Granite Moulding. |
| 26 | Majar Path Cloth Providing cloth for file binding perpose. Rate as per market rate |
| 27 | Dismantling and reassembly Optimizer & Tables in RO & DE Office. |
| 28 | Service charges for dismantling Optz SS1 1200mm 2047mm WG - 24102098SD00948 |
| 29 | Service charges for dismantling Optz SL1 1200mm 2047mm WG - 24102098SD00949 |
| 30 | Service charges for dismantling Optz TM1 1200mm 2047mm WG WP - 24102098SD00951 |
| 31 | Service charges for dismantlingT104 BN.MN+SP.BWN 1665mm 900mm - 56101519SD01113 |
| 32 | Service charges for dismantling Cignus NVNM LH 1800mm 2100mm -56101703SD00425 |
| 33 | Service charges for shifting materials from 1st floor to ground floor |
| 34 | Vehical Arrange for shifting materials from Chincholi to Solapur 25km with unloading |
| 35 | Service charges for Reassembly Optz SS1 1200mm 2047mm WG - 24102098SD00948 |
| 36 | Service charges for Reassembly Optz SL1 1200mm 2047mm WG - 24102098SD00949 |
| 37 | Service charges for Reassembly Optz TM1 1200mm 2047mm WG WP - 24102098SD00951 |
| 38 | Service charges for ReassemblyT104 BN.MN+SP.BWN 1665mm 900mm - 56101519SD01113 |
| 39 | Service charges for Reassembly Cignus NVNM LH 1800mm 2100mm-56101703SD00425 |
| 40 | TADA & Other Charges |
| 41 | Loose Hardware |
| 42 | Providing & fixing 35mm thk. door shutter finish with both side 3 - 4 mm thk. Veneer on both sides as per approved pattern. All edges should finish with teak wood lipping with melamine polish. All complete as per instructions & approval of EIC. Note: The rate of all doors shall include all hardware such as door handles, hinges, door closures/floor spring, dead lock, PVC door buffer, door stopper, latches etc. as required. |
| 43 | Providing & Fixing Hikvizon 8CH DVR DS-720 HUMI-M1/FA |
| 44 | Compactor / Mobile storage cabinet dismantle at Chincholi MIDC & Installation at New Office Building at Solapur Rate as per budgetory offer. |
| 45 | Aluminium Composite Paneling with necessary frame & fitting. |
| 46 | Main Cabin indoor logo with LED Light + Acrylic & Foam Letters |
| 47 | Big Size Name Plate |
| 48 | Small Size Name Plate |
| 49 | Main Board Letters On Building महाराष्ट्र औद्योगिक विकास महामंडळ (महाराष्ट्र शासन अंगिकृत) With logo on both office |
| 50 | Inside office board in English as well as in Marathi in acrylic & foam letters. |
| 51 | Dismantling of installed split AC & reerection in new office building at Solapur with necessary brackets copper pipes, refilling of gas & backfilling of cores of walls at chincholi office & Taking Cores as per requrement (Rate as per Budgetory Offer) |
| 52 | Providing Locks (Rate as per Market Rate) Godrej Make Locks for Office |
| 53 | Providing and fixing precast cement concrete flower bed of wall thickness 75mm including reinforced with welded mesh of 25x25mm sized including arrainagement of drain pipes 75mm in dia at bottom @ 1m c/c either side in stagged manner . The outside finish simillar as ashlar stone masonary . Anchared with the hold fast in the concret bed block ,as per the detailed drawig (Rates Excluding GST)Rate as per Schedule B=Rs.952.00/m Sub Estimate No.10 Item No.8 accepted tender rate 13.37 % above Rate As per accepted tender cost 952.00 + 952.00 x 13.37 % = Rs.1079.28/m Say Rs =1079.00 |
| 54 | Royalty charges for various building construction bonafied materials which are used for government bonafied works and for which Royalty charges are to be paid by the contractor. (This Item is to be paid to the contractor only after he pays the Royalty amount to Revenue department and produces the required voucher.) |
| 55 | Laboratory testing charges for various materials required for items of work, on the basis of testing frequency and charges fixed by Vigilence and Quality Control Circle, Pune. |
| 56 | Fineness Modules (Sieve Analysis), Silt and Clay Content Test for Sand |
| 57 | Standard Consistancy, Fineness, Specific Gravity, Setting Time (Initial and Final), Compressive Strength, Soundness Test for Cement |
| 58 | Compressive Strength of Cement Mortar. |
| 59 | Compressive Strength, Water Absorption Test for Paving Blocks - 80 milimetre thick, 400 Kilogram per Square Centimetre Strength |
| 60 | Fineness Modulus (Sieve Analysis), Silt and Clay Content Test for Artificial Sand |
| 61 | Sieve Analysis Test for Metal below 40 milimetre. |
| 62 | Water Absorption, Specific Gravity, Impact Value, Crushing Value Test for Metal below 40 milimetre. |
| 63 | Compressive Strength of Cement Concrete Cube |
| 64 | Crushing Value / Compressive Strength, Water Absorption, Specific Gravity Test for Stone / Rubble Please Enable Macros to View BoQ information |
