Name of Work:- Renovation of Physical Research Lab No.2 on 2nd Floor of Department of Chemistry in P.U. C us Sector-14, Chandigarh.
Sl. No.
Item Description
1
Civil Work
2
Providing and fixing Wall Table ( 13'-8\\" x 2'-3\\" x 2'-9\\") It shall be 20mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 25 mm at the sides The suspended under-bench welded units should be supported on heavy-duty steel frames fully carrying the load of worktops. Its superior strength combined with aesthetically appealing end caps shall give maximum flexibility and modularity while making a layout. D-frame should be constructed from a square pipe with a cross section of 30mm x 30mm and should be a minimum 1.6 mm thick. The D-frame legs should be supplied with adjustable levelling screw (M-10 levelers of Nylon + MS, tolerance from -5mm to +15mm) to correct the unevenness of flooring. The tubular enclosed type construction shall discourage dust accumulation and unwanted development of bacteria & fungus. Drainage gradient should be well adjusted throughout the length of table and should have horizontal supports for drainage systems. It should be suitable for sitting and standing nominal heights of 750mm & 900mm respectively. The nominal table depths should be 450mm, 600mm, 750 mm for wall side and 1050mm, 1200mm, 1500mm for Island tables. The Corner Units shall fit well with 750mm & 900mm table depths. All frame-work is should be pre-treated with superior pure epoxy powder coated finish. These should be made from square pipes of 1.6 mm thickness. Cross-sectional dimensions of the pipe should be 30 x 30mm with a minimum of 1.6 mm. They should be made of CRCA MS and coated with pure epoxy powder. These connect two D-Frames together as shown using Cclamps/U-clamps. Together with the D-Frames and Horizontal Members connected together, the skeletal structure of the work-bench is formed on which the worktop can be placed and the hanging-type storage cabinets can be suspended. Horizontal Members determine the width of the lab workbench as they form the member (distance) between two adjacent D-Frames. They should be available in various widths of 450, 600, 1050, 1200, and 1500.All leg-space panels, rear cover panels, island side panels etc. should be made from CRCA MS panels of minimum 0.8mm thickness with pure epoxy powder coating Under bench cabinets are to be Pure epoxy powder coated with thickness of 40-60 microns and should be suspended from tubular structure. The cabinet should have a corrosion resistance magnetic strip as shutter catch, shutter and drawer are to be equipped with 180 degree cam lock. PP constructed semi recessed handle to be screw fitted to the shutters. Hinges are to be of SS-304 knuckle overlay type with 270 degree opening and 2 nos of hinges are to be screw fitted to each shutter and cabinet.Unit Construction : It should be Welded body construction with load bearing members such as top, bottom and stiffeners should have a minimum thickness of 0.8 mm and drawer separator should be of 1.2mm thick. Shelf : Should be made of 0.8mm thickness which should be adjustable to 6 steps of 50mm. Shutter should be over-closing type. It has a sandwich door construction with shutter front & shutter cover with 1.2mm thick hinge stiffener. Empty gap should with filled with 15mm thick paper honeycomb for sound ampening.Drawer: Should be welded single piece construction with over-closing sandwich drawer front filled with 15mm thick paper honeycomb for sound dampening.Units should be in 450mm and 600mm widths.Used for housing electrical switches and sockets, its top panel, bottom panel of the trunking should be made from minimum of 0.8mm thick body. It should be available in both, single sided and double-sided configurations. It should be made from CRCA MS with pure epoxy powder coating. The front surface that houses the electrical points should have a slope.
3
Providing and fixing Wall Table ( 12'-0\\" x 2'-3\\" x 2'-9\\") It shall be 20mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 25 mm at the sides The suspended under-bench welded units should be supported on heavy-duty steel frames fully carrying the load of worktops. Its superior strength combined with aesthetically appealing end caps shall give maximum flexibility and modularity while making a layout. D-frame should be constructed from a square pipe with a cross section of 30mm x 30mm and should be a minimum 1.6 mm thick. The D-frame legs should be supplied with adjustable levelling screw (M-10 levelers of Nylon + MS, tolerance from -5mm to +15mm) to correct the unevenness of flooring. The tubular enclosed type construction shall discourage dust accumulation and unwanted development of bacteria & fungus. Drainage gradient should be well adjusted throughout the length of table and should have horizontal supports for drainage systems. It should be suitable for sitting and standing nominal heights of 750mm & 900mm respectively. The nominal table depths should be 450mm, 600mm, 750 mm for wall side and 1050mm, 1200mm, 1500mm for Island tables. The Corner Units shall fit well with 750mm & 900mm table depths. All frame-work is should be pre-treated with superior pure epoxy powder coated finish. These should be made from square pipes of 1.6 mm thickness. Cross-sectional dimensions of the pipe should be 30 x 30mm with a minimum of 1.6 mm. They should be made of CRCA MS and coated with pure epoxy powder. These connect two D-Frames together as shown using Cclamps/U-clamps. Together with the D-Frames and Horizontal Members connected together, the skeletal structure of the work-bench is formed on which the worktop can be placed and the hanging-type storage cabinets can be suspended. Horizontal Members determine the width of the lab workbench as they form the member (distance) between two adjacent D-Frames. They should be available in various widths of 450, 600, 1050, 1200, and 1500.All leg-space panels, rear cover panels, island side panels etc. should be made from CRCA MS panels of minimum 0.8mm thickness with pure epoxy powder coating Under bench cabinets are to be Pure epoxy powder coated with thickness of 40-60 microns and should be suspended from tubular structure. The cabinet should have a corrosion resistance magnetic strip as shutter catch, shutter and drawer are to be equipped with 180 degree cam lock. PP constructed semi recessed handle to be screw fitted to the shutters. Hinges are to be of SS-304 knuckle overlay type with 270 degree opening and 2 nos of hinges are to be screw fitted to each shutter and cabinet.Unit Construction : It should be Welded body construction with load bearing members such as top, bottom and stiffeners should have a minimum thickness of 0.8 mm and drawer separator should be of 1.2mm thick. Shelf : Should be made of 0.8mm thickness which should be adjustable to 6 steps of 50mm. Shutter should be over-closing type. It has a sandwich door construction with shutter front & shutter cover with 1.2mm thick hinge stiffener. Empty gap should with filled with 15mm thick paper honeycomb for sound ampening.Drawer: Should be welded single piece construction with over-closing sandwich drawer front filled with 15mm thick paper honeycomb for sound dampening.Units should be in 450mm and 600mm widths.Used for housing electrical switches and sockets, its top panel, bottom panel of the trunking should be made from minimum of 0.8mm thick body. It should be available in both, single sided and double-sided configurations. It should be made from CRCA MS with pure epoxy powder coating. The front surface that houses the electrical points should have a slope.
4
Providing and fixing WELDED OVER HEAD STORAGE CABINETS ( 12'-0\\" x 1'-3\\" x 2'-0\\") Over head cabinets are to be Pure epoxy powder coated with thickness of 40-60 microns and should be fixed on the wall. The cabinet should have a corrosion resistance magnetic strip as shutter catch, shutters are to be equipped with 180 degree cam lock. PP constructed semi recessed handle to be screw fitted to the shutters. Hinges are to be of SS-304 knuckle overlay type with 270 degree opening and 2 nos of hinges are to be screw fitted to each shutter and cabinet.Unit Construction : It should be Welded body construction with load bearing members such as top, bottom and stiffeners should have a minimum thickness of 0.8 mm. Shelf : Should be made of 0.8mm thickness which should be adjustable to 6 steps of 50mm. Shutter should be over-closing type. It has a sandwich door construction with shutter front & shutter cover with 1.2mm thick hinge stiffener. Empty gap should with filled with 15mm thickpaper honeycomb for sound dampening.Units should be in 450mm and 600mm widths.
5
Providing and fixing Island Table ( 12'-0\\" x 5'-0\\" x 3'-0\\") It should be 20mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 25 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. A representation ofthe worktop edges is shown as under Made up of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. Bowl size to be a minimum of (L x W x D) 560 x 355 x 300 mm. Faucet should be 3-way type faucet of reputed make (Ex. Premier Polymer) Used for housing electrical switches and sockets, its top panel, bottom panel of the trunking should be made from minimum of 0.8mm thick body. It should be available in both, single sided and double-sided configurations. It should be made from CRCA MS with pure epoxy powder coating. The front surface that houses the electrical points should have a slope. Please Enable Macros to View BoQ information
We takes all possible care for accurate & authentic tender information, however Users
are requested to refer Original source of Tender Notice / Tender Document published by
Tender Issuing Agency before taking any call regarding this tender.
