|
| 1 | Providing and applying tack coat with bitumen VG-10 bitumen pressure distributor at the rate of 0.30 kg per sum on the prepared bituminous surface cleaned with mechanical broom. As per MORT&H Clause 503 (iii) (on Cement Concrete Pavement) |
| 2 | Providing and laying dense graded bituminous macadam with higher capacity batch type HMP using crushed aggregates of specified grading, premixed with bituminous binder @4.5 Percent by weight of total mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MoRTH specification clause No. 505 complete in all respects. (Grade-II) |
| 3 | Providing and applying tack coat with bitumen VG-10 bitumen pressure distributor at the rate of 0.20 kg per sum on the prepared bituminous surface cleaned with mechanical broom. As per MORT&H Clause 503 (i) (on DBM Surfac) |
| 4 | Providing and laying bituminous concrete with 100-120 tonne per hour capacity batch type hot mix plant using crushed aggregates of specified grading, premixed with bituminous binder @ 5.4 Percent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specificationclause No. 507 complete in all respects (Grade-II) |
| 5 | Providing and laying of hot appiled thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, Thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC: 35 -2015 The finished surface to be level, uniform and free from streaks and holes |
| 6 | Supply & Fixing of Pavement maker (Cat eye) Type Z-ASTMD-4956-04 Avery Dennison/3-M (USA MAKE) consisting of ASA plastic housing fitted with tighty adherent ploiting compound. The housing shall contain prismatic two glass covered prismatic reflective face to reflect incident light I/C all tax. RPM (With shank) |
| 7 | Construction of Embankment with Material obtained from Borrow pits (Lead Km-3)Construction of embankment with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2. |
| 8 | Supply and erection of direction and place identification retro reflctorised sign as per IRC 67 made of high intensity grade sheeting vede clause 801.30, fixed over aluminium sheeting, 2 mm. thick steel single angle iron post 75 x 75 x 6 mm. firmly fixed to the ground by means of properly designed fondation with M-15 grade cement concrete 45 x45 x 60 mm. 60 cm. below ground level as per approved drawing (informatry Borad of Size less than .9 SQM) |
| 9 | Providing and laying of hot appiled thermoplastic compound 5.00 mm thick including reflectorising glass beads @ 500 gms per sqm area, Thickness of 5 mm is exclusive of surface applied glass beads as per IRC: 35-2015 The finished surface to be level, uniform and free from streak and holes Repeated Bar |
| 10 | Supply and fixing of retroreflective high intensity informatory sign board/ cautionary sign board etc. As per MoRTH specification.T Junction Sign Board |
| 11 | Providing and erecting direction and place identification retro-reflectorised sign 0.64 Sqm as per IRC:67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick with area not exceeding 0.9 sqm supported on a mild steel single angle iron post 75 x 75 x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 x 45 x 60 cm, 60 cm below ground level as per approved drawing. Intersection and Give Way, Speed Limit Sign Board |
| 12 | Providing and erecting direction and place identification retro-reflectorised sign 0.64 Sqm as per IRC:67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick with area not exceeding 0.9 sqm supported on a mild steel single angle iron post 75 x 75 x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 x 45 x 60 cm, 60 cm below ground level as per approved drawing Village Board |
| 13 | Supply and erection of direction and place identification retro reflctorised sign as per IRC 67 made of high intensity grade sheeting vede clause 801.30, fixed over aluminium sheeting, 2 mm. thick steel single angle iron post 75 x 75 x 6 mm. firmly fixed to the ground by means of properly designed fondation with M-15 grade cement concrete 45 x45 x 60 mm. 60 cm. below ground level as per approved drawing.Help Line Board (60x60CM) Please Enable Macros to View BoQ information |
