Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | GST % for the tender Please select the rate of GST in cell AY13. Rate selected shall be applicable for the entire BoQ. |
| 2 | Civil Works |
| 3 | Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas including dressing of sides and ramming of bottoms including getting out the excavated soil and disposal of surplus excavated soil, all works up to any lead and lift, as di rected by the Engineer-in-Charge : |
| 4 | In all kinds of soil |
| 5 | In Ordinary rock |
| 6 | Excavating trenches by mechinical / manual means of required width in all kinds of soil for pipes, cables, etc. including excavation for sockets, and dressing of sides, ramming of bottoms, for all depth, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, et c. and disposing of surplus excavated soil, all work up to any lead & lift as directed by the Engineer-in-Charge : |
| 7 | Pipes, cables etc. not exceeding 80 mm dia. |
| 8 | Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia |
| 9 | Pipes, cables etc. exceeding 300 mm dia but not exceeding 600 mm |
| 10 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in d epth, consolidating each deposited layer by ramming and watering, all works up to any lead and lift. |
| 11 | Supplying and filling selected earth/ moorum (excluding black cotton soil) from Contractor's own borrow areas including royalty, wit h all leads and lifts in trenches, plinth, sides of foundation etc. including watering, compacting in layers not exceeding 20cm thic kness, complete in all respects inclusive of cost of all labour, materials, tools, tackles etc. as per drawings, specifications and direction of Site Engineer. |
| 12 | Disposal of moorum/ building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including l oading, transporting, unloading to designated location/ approved municiple dumping ground for lead up to 10 Km and for all lifts, co mplete as per directions of the Engineer-in-Charge. [Note: This item shall also be applicable in urban areas having directions for r estricted hours for movement/ plying of load carrying motor vehicles of 3.5 cum or more.] |
| 13 | Supplying and filling coarse sand under floors, in foundations and plinth including cost-of sand, royalty, transportation, loading , unloading, spreading in layers not exceeding 20 cm., watering, ramming, compacting, dressing and levelling etc. complete in all r espects inclusive of cost of all labour, materials, tools, tackles etc. as per drawings, specifications and direction of Site Engine er. |
| 14 | Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a hei ght of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared. |
| 15 | Supplying chemical emulsion (Chlorpyriphos/ Lindane emulsifiable concentrate of 20%) in sealed containers including delivery as spec ified. |
| 16 | Diluting and injecting chemical emulsion (Chlorpyriphos/ Lindane E.C. 20% with 1% concentration) for POST-CONSTRUCTIONAL anti-termit e treatment (excluding the cost of chemical emulsion) : |
| 17 | Along external wall where the apron is not provided using chemical emulsion @ 7.5 litres/ sqm of the vertical surface of the substru cture to a depth of 300 mm including excavation channel along the wall & rodding etc. complete : |
| 18 | Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 : 2 (1 cement : 2 Coarse sand) to match the existing floor : |
| 19 | Providing and laying in position cement concrete of specified grade at all depths including ramming & shuttering etc. complete in a ll respects inclusive of cost of all labour, materials, tools, tackles etc. as per drawings, specifications and direction of Site En gineer: |
| 20 | 1:2:4 [1 cement : 2 coarse sand (Zone-III) derived from natural sources : 4 graded stone aggregate 40 mm nominal size derived from n atural sources] |
| 21 | 1:3:6 (1 cement : 3 coarse sand (Zone-III) derived from natural sources : 6 graded stone aggregate 40 mm nominal size derived from n atural sources) |
| 22 | 1:4:8 [1 cement : 4 coarse sand (Zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from n atural sources] |
| 23 | Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's sp ecification. [Note: Unit \\"KG\\" shall mean \\"PER BAG OF 50 KG OF CEMENT\\"]. |
| 24 | Providing and laying damp-proof course 50 mm thick with cement concrete 1:2:4 [1 cement : 2 coarse sand (Zone-III) derived from natu ral sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources] laid to proper level & line including provid ing shuttering & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7 Kg per square metre o n damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil etc. co mplete in all respects inclusive of cost of all labour, materials, tools, tackles etc. as per drawings, specifications and direction of Site Engineer. |
| 25 | Making plinth protection 50 mm thick of cement concrete 1:3:6 [1 cement : 3 coarse sand derived from natural sources : 6 graded ston e aggregate 20 mm nominal size derived from natural sources] over 75 mm thick bed of dry brick ballast 40 mm nominal size, well ramm ed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth, etc . complete in all respects inclusive of cost of all labour, materials, tools, tackles etc. as per drawings, specifications and direc tions of the Engineer-in-Charge. |
| 26 | Steel reinforcement for R.C.C. workincluding initial straightening of coiled/uncoiled bars, removal of loose rust, cutting, bending to correct size & shape, binding with 18 gauge G.I. wire at each intersection and placing at any position, at any height and depth complete in all respects inclusive of cost of all labour, materials, tools, tackles etc. as per drawings, specifications and directi on of Site Engineer. : Thermo-Mechanically Treated bars of grade Fe-500 D or more |
| 27 | Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections. |
| 28 | \\"Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, ad mixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workabilit y without impairing strength; including pumping of concrete to site of laying, the cost of centering, shuttering, finishing, curing, carriage for all leads, as per direction of the engineer-in-charge, for the following grades of concrete.: Note: 1. Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cemen t content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re -design the mix or bear the cost of extra cement. 2.Payment for Reinforcement shall be made as per relevant item of SOR.\\" |
| 29 | All works upto plinth level |
| 30 | Concrete of M25 grade with minimum cement content of 330 kg /cum |
| 31 | Concrete of M30 grade with minimum cement content of 350 kg /cum |
| 32 | All works above plinth level upto floor V level |
| 33 | Concrete of M25 grade with minimum cement content of 330 kg /cum |
| 34 | Concrete of M30 grade with minimum cement content of 350 kg /cum |
| 35 | Add for using extra cement in the items of design mix over and above the specified cement content therein. [Note: Unit \\"QN\\" shall me an \\"QUINTAL\\"] |
| 36 | Brick work with non modular fly ash bricks conforming to 1S:12894, class designation 10 average compressive strength in super struct ure above plinth level up to floor V level in : |
| 37 | Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 38 | Half brick masonry with non modular fly ash bricks of class designation 10, conforming to IS :12894, in super structure above plinth upto floor V level. |
| 39 | cement mortar 1:4 (1 cement : 4 coarse sand) |
| 40 | Extra for providing and placing in position 2 Nos. 6 mm dia. M.S. bars at every third course of half brick masonry. |
| 41 | Providing and laying Autoclaved Aerated concrete(AAC) blocks masonry with 150 mm to 300 mm thick with Grade-1 AAC blocks of density 551 to 650 kg/cum conforming to 1S:2185 (Part 3) in super structure above plinth level up to floor V level with RCC band at sill lev el and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately). |
| 42 | Providing and laying Autoclaved Aerated concrete(AAC) blocks masonry 100 mm/ 125 mm thick with Grade-1 AAC blocks of density 551 to 650 kg/cum conforming to 1S:2185 (Part 3) in super structure above plinth level up to floor V level in cement mortar 1:4 (1 cement : 4 coarse sand ). The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work . |
| 43 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in : |
| 44 | Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 45 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in : |
| 46 | Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 47 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut Granite stone slab of colour black, Cherry/Ruby red for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approve d shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cemen t, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finis h etc. complete at all levels : |
| 48 | Area of slab over 0.50 sqm |
| 49 | Extra for fixing marble/ granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete. |
| 50 | Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar lo cation in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of c ut edges etc. complete. |
| 51 | Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75 x 50 cm deep and 1.8 cm thick, fixed in ur inal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or w ith cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per directions of the Engineer- in-Charge and finished smooth : |
| 52 | Granite Stone of approved shade |
| 53 | Providing and fixing machine cut, mirror/ eggshell polished Italian Marble stone slab (Perlato, Rosso verona, Fire Red or Dark Emper adore etc.) of 18 mm thickness for wall lining (veneer work) including dado, skirting, risers of steps etc., in required design and pattern wherever required, stones of different finished surface texture, on 12 mm (average) thick cement mortar 1:3 (1 cement : 3 co arse sand) laid and jointed with white cement slurry @ 3.3 Kg/sq.m. including pointing with white cement slurry admixed with pigment of matching shade, including rubbing, curing, polishing etc. all complete as per Architectural drawings, and as directed by the Eng ineer-in-Charge : |
| 54 | Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open g rooves for linear as well as curvilinear portions of the building, for all heights and all levels etc. including: (A) Structural ana lysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of w ater to make it watertight including checking of all the structural and functional design. (B) Providing, fabricating, supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4 mm thick alumin ium composite panel material consisting of 3 mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5 mm thi ck). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF/ Lumiflon based fluoropolymer resi n coating of approved colour and shade on face #1 and polymer (Service) coating on face #2 as specified using stainless steel screws , nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. (C) The fastening brackets of Aluminium alloy 6005 T5/ MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bo lts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specificati on and drawing. The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium co mposite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Inlcuding Base frame work for ACP cladding. The Contractor shall provide curtain wall with aluminium c omposite panel cladding, having all the performance characteristics all complete, as per the Architectural drawings, as per item des cription, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of pay ment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groov e) shall be measured in square metre up to two decimal places. |
| 55 | Providing & fixing Factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other frame/ Chow khat comprising of virgin PVC Polymer of K value 58-60 (Suspension Grade), calcium corbonate and natural fibers (wood powder/rice hu sk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100gms) fabricated with milter joints after applying PVC so lvent cement and screwed with full body threaded star headed SS Screws having minimum frame density of 750kg/cum, screws withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of frame of class A category with property of being termite/ borer proof, water/ moisture proff and fire retardant and fix ed in position with M.S hold fast/lugs/SS dash fastners of required dia and length complete as per direction of Engineer-in-charge. (M.S hold fast/lugs or SS dash fastners shall be paid for separately). |
| 56 | Frame size 50 x 100 mm |
| 57 | Frame size 65 x 150 mm. |
| 58 | Providing and fixing ISI marked flush door shutters conforming to IS:2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on bot h faces of shutters : |
| 59 | 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 60 | Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). |
| 61 | Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embe dding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size). |
| 62 | Providing and fixing teak wood moulding finished with melamine polish complete in all respects inclusive of cost of all labour, mate rials, tools, tackles etc. as per drawings, specifications and directions of the Engineer-in-Charge : |
| 63 | 75 mm x 50 mm |
| 64 | Providing & Fixing 1 mm thick decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish of appro ved make with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, inc luding cost of adhesive of approved quality, all complete as per directions of Engineer in Charge. |
| 65 | Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod pf approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without high performance coatings as per design requirements and conforming to IS: 3548 & IS:16231 shall be paid separately. Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for: (i) Sites with basic wind speed > 45 m/sec as per IS 875 - Part 3 (ii) Sites with structure height more than 20m for all wind speeds. |
| 66 | Casement window single panel with S.S. 304 friction hinges as per size and weight of sash, multi-point locking system, zinc alloy (z amak) powder coated handles. Using R2 series with frame (39mm & above) x (39mm & above) & sash (39mm & above) x (60mm & above). (Hei ght upto 1.2 meter) |
| 67 | Casement window double panels with fixed mullion with S.S. 304 friction hinges as per size and weight of sash, multi-point locking s ystem, zinc alloy (zamak) powder coated handles. Using R2 series with frame (39mm & above ) x (39mm & above) & sash (39mm & above) x (60mm & above) & mullion (39mm & above) x (60mm & above). (Height upto 1.2 meter). |
| 68 | Fixed window / ventilator with mullion / transom. Using R1 series with frame (33mm & above ) x (35mm & above) & mullion (33mm & abov e) x (50mm & above). (Height upto 0.90 meter) |
| 69 | Providing and fixing Pre-laminated medium density fibre board IS 14587:1998 marked, with one side decorative lamination and other si de balancing lamination Grade-I (exterior grade), in shelves with screws and fittings wherever required, edges to be sealed with PVC edge bending tape 2.00 mm thick of approved brand. [Note: Fittings to be paid separately] : |
| 70 | Pre-laminated with decorative lamination one side and other side balancing lamination exterior Grade - | MDF Board 18 mm thick confo rming to 1S:14587 |
| 71 | Providing and fixing IS:12817 marked stainless steel butt hinges with stainless steel screws etc. complete : |
| 72 | 100X58X1.90 mm |
| 73 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS:1868), tr ansparent or dyed to required colour or shade, with nuts and screws etc. complete : |
| 74 | 250x16 mm |
| 75 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS:1868) transparent o r dyed to required colour or shade, with necessary screws etc. complete : |
| 76 | 100 mm |
| 77 | Providing and fixing of Medium Duty hollow metal fire rated doors as per IS 3614: 2021, for 120min integrity & 30min. insulation. Pressed galvanized steel confirming to IS 277 with the following specification. Recommended fire door shall be tested as per IS/ISO 3008-1 & IS/ ISO 834-1, from Exova/TBW/CBRI approved lab. Labled fire doors shall be with fire rated hardware and vision panel all as a complete assembly. Proper label confirming the type of door and the hourly rating is mandatory. Door frame shall be step rebate grooved profile of size 125 x 75mm made out of 1.20mm (18gauge) minimum thick galvanized steel sheet. Frames shall be mitered and field assembled with self tabs. Frames to have inbuild grooved sealing system for taking fire rated EPDM seals. All provision should be mortised, drilled and tapped for receiving appropriate hardware. Frames should be provided with back plate bracket and anchor fasteners for installation on a finished plastered masonry wall opening. Frames shall be filled with fire rated puff. Door leaf shall be 60mm thick fully flush double skin step design door, insulated with or without vision lite. Door leaf shall be manufactured from 1.2mm (18gauge) minimum thick galvanised steel sheet. The internal construction of the door should be rigid reinforcement pads for receiving appropriate hardware. The infill material shall be 120kg/m3 high density mineral wool insulation material. Intumescent seals 15 x 1.5mm to be provided. All doors shall be factory prepped for receiving appropriate hardware and provided with necessary reinforcement for hinges, locks, and door closers. The edges should be interlocked with a bending radius of 1.4mm. For pair of doors integrated astragals has to be provided on the meeting stile for both active and inactive leaf. Vision lite wherever applicable should be provided for 6mm clear borosilicate fire rated glass as per manufacturers recommendation with a clipon arrangement. Door and frames shall be finished Pure Polyster Powder coated and shall have passed minimum 500 hours of salt spray test. Door and frames shall be finished Pure Polyster Powder coated and shall have passed minimum 500 hours of salt spray test. Rate shall include supply and installation of frame, shutter as a complete assembly, including all hardware, smoke seals & glass with tapes |
| 78 | 120 Mins Fire Rated Insulated Door FD Double leaf of size 2000 x 2100mm with vision panel 200 x 300mm with hardware set 2 |
| 79 | \\"Providing and fixing approved brand and manufacture of Rack and pinion door closer TS 68 EN size 2/3/4, with std. arm and with two independent closing valves and latching speed adjustable by arm. Silver finish. As per EN 1154. Approved Make : dormakaba / Hafele / GEZE or equivalent with necessary accessories and screws etc. complete in all respects as per manufacture ofrs' specificatios & as directed by Engineer-in-charge.\\" |
| 80 | \\"Providing and fixing approved brand and manufacture of Pull Handle TGDI-D 300 back to back with adjustable fixing for glass, wood and metal doors in satin stainless steel. The pull handles should have supporting washer with raised bevelling on the outer surface. Length =300mm, 22mm dia, SS304 Approved Make : dormakaba / Hafele / GEZE or equivalent with necessary accessories and screws etc. complete in all respects as per manufacture ofrs' specificatios & as directed by Engineer-in-charge. \\" |
| 81 | \\"Providing and fixing approved brand and manufacture of Male/ Female sign plate 3020-M / 3030-F for WC application with fixing screws size 125 x 125mm, rounded corners in SS 304 satin stainless steel finish. Marking in black Approved Make : dormakaba / Hafele / GEZE or equivalent with necessary accessories and screws etc. complete in all respects as per manufacture ofrs' specificatios & as directed by Engineer-in-charge. \\" |
| 82 | \\"Providing and fixing approved brand and manufacture of 4012 wall mounted door stop dome with 60mm length with fixing accessories Approved Make : dormakaba / Hafele / GEZE or equivalent with necessary accessories and screws etc. complete in all respects as per manufacture ofrs' specificatios & as directed by Engineer-in-charge.\\" |
| 83 | \\"Providing and fixing approved brand and manufacture of Disable sign plate 3040-D for WC application with fixing screws size 125 x 125mm, rounded corners in SS 304 satin stainless steel finish. Marking in black Approved Make : dormakaba / Hafele / GEZE or equivalent with necessary accessories and screws etc. complete in all respects as per manufacture ofrs' specificatios & as directed by Engineer-in-charge.\\" |
| 84 | Providing and fixing approved brand and manufacture of Coat hook 3106 with face fixing screws in satin stainless steel Approved Make : dormakaba / Hafele / GEZE or equivalent with necessary accessories and screws etc. complete in all respects as per manufacture ofrs' specificatios & as directed by Engineer-in-charge. |
| 85 | Providing and fixing approved brand and manufacture of 3108 Floor stop half dome with 45mm dia with fixing accessories, in satin Chrome Approved Make : dormakaba / Hafele / GEZE or equivalent with necessary accessories and screws etc. complete in all respects as per manufacture ofrs' specificatios & as directed by Engineer-in-charge. |
| 86 | \\"Providing and fixing approved brand and manufacture of Pure 8100 Type 3 Package with Pair of Pure 8100 Design Lever Handle on Roses & escutcheons. Including 271a Sash lock with 72mm CTC, 55mm Backset 20mm Square forend. EPC 60mm length oneside thumb turn otherside coin release operation Approved Make : dormakaba / Hafele / GEZE or equivalent with necessary accessories and screws etc. complete in all respects as per manufacture ofrs' specificatios & as directed by Engineer-in-charge.\\" |
| 87 | \\"Providing and fixing approved brand and manufacture of Pure 8100 Type 1 Package with Pair of Pure 8100 Design Lever Handle on Roses & escutcheons. Including 271a Sash lock with 72mm CTC, 55mm Backset 20mm Square forend. EPC 60mm length both side key operation Approved Make : dormakaba / Hafele / GEZE or equivalent with necessary accessories and screws etc. complete in all respects as per manufacture ofrs' specificatios & as directed by Engineer-in-charge.\\" |
| 88 | \\"Providing and fixing approved brand and manufacture of Top Pivot Approved Make : dormakaba / Hafele / GEZE or equivalent with necessary accessories and screws etc. complete in all respects as per manufacture ofrs' specificatios & as directed by Engineer-in-charge.\\" |
| 89 | \\"Providing and fixing approved brand and manufacture of Top Patch Fitting Approved Make : dormakaba / Hafele / GEZE or equivalent with necessary accessories and screws etc. complete in all respects as per manufacture ofrs' specificatios & as directed by Engineer-in-charge.\\" |
| 90 | \\"Providing and fixing approved brand and manufacture of Bottom Patch Fitting Approved Make : dormakaba / Hafele / GEZE or equivalent with necessary accessories and screws etc. complete in all respects as per manufacture ofrs' specificatios & as directed by Engineer-in-charge.\\" |
| 91 | \\"Providing and fixing approved brand and manufacture of Floor spring BTS 75V EN 1-4 with std. spindle and cover plate. The floor spring with backcheck and adjustable closing speed from 175°. . With 90°. hold open. As per EN 1154. (not suitable for fire doors) Finish: Satin stainless steel. Application - Glass Doors Approved Make : dormakaba / Hafele / GEZE or equivalent with necessary accessories and screws etc. complete in all respects as per manufacture ofrs' specificatios & as directed by Engineer-in-charge. \\" |
| 92 | \\"Providing and fixing approved brand and manufacture of Lock with Strike plate & EPC Approved Make : dormakaba / Hafele / GEZE or equivalent with necessary accessories and screws etc. complete in all respects as per manufacture ofrs' specificatios & as directed by Engineer-in-charge.\\" |
| 93 | \\"Providing and fixing approved brand and manufacture of Surface Mounted Tower bolt 3200-2 of Length 6\\"\\" in Satin chrome finish Approved Make : dormakaba / Hafele / GEZE or equivalent with necessary accessories and screws etc. complete in all respects as per manufacture ofrs' specificatios & as directed by Engineer-in-charge. \\" |
| 94 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required : |
| 95 | In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete. |
| 96 | In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. |
| 97 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. comple te : |
| 98 | Hot finished welded type tubes |
| 99 | Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, to p lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. s heet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shap e as per standard drawing. |
| 100 | Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 m dia polyamide PA 6 grade sleeve, including drilling of hole in frame , c oncrete/ masonry, etc. as per direction of Engineer-in-charge. |
| 101 | 10 x 80 mm |
| 102 | Providing and fixing Stainless Steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, b uffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts comple te, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of require d size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of the Engineer-in-Charge. [Note : For payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, f asteners etc.] |
| 103 | Providing Toughened glass 12 mm thickness fixed to stainless steel ( Grade 304) railing made of Hollow tubes and fixing accessories such as nuts, bolts, fasteners etc.(excluding Stainless steel railing ) |
| 104 | 40 mm thick cement concrete Flooring with P.C.C. of grade mix 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nomin al size) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. compl ete : |
| 105 | Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles,including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse s and). |
| 106 | Light shade pigment using white cement. |
| 107 | Extra for pre finished nosing to treads of steps of marble / granite stone. |
| 108 | Extra for marble / granite stone flooring in treads of steps and risers using single length up to 2.00 metre. |
| 109 | Kota stone slab flooring 25 mm thick over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigmen t to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse san d) : |
| 110 | Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cemen t: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and poli shing complete. |
| 111 | Providing and laying Double Charge Vitrified Tiles (polished finish) of specified sizes (thickness to be specified by the Manufactur er) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacture, in all colours and shades, la id on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 Kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only. Laying of til es will be done with the notch trowel, plier, wedge, clips of required thickness, levelling system and rubber mallet for placing the tiles gently and easily : |
| 112 | Size of Tile 600 x 600 mm |
| 113 | Providing and laying Glazed Vitrified Tiles (polished finish) of specified sizes (thickness to be specified by the Manufacturer) wit h water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacture, in all colours and shades, laid on 2 0 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 Kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only. Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, levelling system and rubber mallet for placing the tiles gently and easily : |
| 114 | Size of Tile 600 x 1200 mm |
| 115 | Providing and laying Glazed Vitrified Tiles (Matt/ Antiskid finish) of specified sizes (thickness to be specified by the Manufacture r) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacture, in all colours and shades, lai d on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 Kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only. Laying of tile s will be done with the notch trowel, plier, wedge, clips of required thickness, levelling system and rubber mallet for placing the tiles gently and easily : |
| 116 | Size of Tile 600 x 600 mm |
| 117 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to IS:15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of c ement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 Kg/sq.m. including grouting the joint with white cement & matching pigments etc. complete : |
| 118 | Size of Tile 600x600 mm |
| 119 | Providing and laying machine cut, mirror polished Marble stone flooring, in required design (Simple geometrical, abstract etc.) and in patterns in combination with Italian marble stone slabs (Perlato, Rosso verona, Fire Red or Dark Emperadore, etc.) of different c olours, shades and finished surface texture etc., in linear portions of the building, all complete as per the architectural drawings , with 18 mm thick stone slab laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4 Kg/sq.m. including pointing with white cement slurry admixed with pigment to match the marble shade i ncluding rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : |
| 120 | Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of t he building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mor tar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. |
| 121 | Polished Granite stone slab of colour Black, Cherry/Ruby Red or equivalent |
| 122 | Providing and Laying 8mm thick VIBRANCE Laminate Floors confirming to EN 13329 standards. Class of Use 23/32, Grade AC4 with all cer tifications. The cost includes fixing of flooring and accessories such skirting, door trims, etc |
| 123 | Supply and Installation of 6mm thick Exterior grade F- Quality panels of standard size with both side décor .FunderMax Exterior pan els are Duromer high-pressure laminates (HPL) as per EN 438-6 type EDF manufactured with norm conformity of EN 438-7 using patented NT Technology (NT is Non fading high performance acrylic polyurethane surface Technology). Panels will be double hardened including acrylic polyurethane resin and thermally cured under high pressure. These Panels will have CE-Mark necessary for their use in buildi ng applications. Installation of FunderMax panels will be done by MBE Rivets (with Fixed and Sliding Points) with recommended Alumin um T section of 75x37x2.8 mm thick and L section 38x38x2.8mm thick held by Aluminum Wall Bracket with Wind load and Dead load slot a s designed and provided, anchored by standard anchor fasteners along with Thermal Separator. Installation of Panels will be done usi ng Rear Ventilated Principles only, which is ensured by providing ventilation gap minimum 200 cm2/ per Meter (for free flow of air b ehind the façade) for the façade and using the framework with no horizontal section. |
| 124 | HPL Cladding |
| 125 | HPL False Ceiling |
| 126 | Providing gola 75x75 mm (in 75x75 mm deep chase) in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and do wn gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design. |
| 127 | Making Khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggr egate of 20 mm nominal size) over P.V.C. sheet 1 m x 1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse s and) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. |
| 128 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : |
| 129 | 12.5 mm thick tapered edge gypsum moisture resistant board |
| 130 | Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture of size 595x595 mm in true horizontal level, suspended on interlocking metal grid of hot dipped galvanised steel sections (g alvanising @ 120 grams/sq.m. including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross 'T' of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main 'T' at 600 mm centre to centre to form a grid of 1200x600 mm and second ary cross 'T' of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be interlocked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls/ partitions on a Perimeter wall angle pre-coated steel of size 24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture in the grid, inc luding cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever require d. Main 'T' runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia an d 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85x30x0.8 mm, spaced at 1200 mm cen tre to centre along main 'T', bottom exposed with 24 mm of all 'T' sections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by the Engineer-in-Charge. [Note: Only calcium silicate false ceiling area will be measured from wall to wall. No deduction shall be made for exposed frames/ opening (cut outs) having area less than 0.30 sqm . The calcium silicate ceiling tile shall have NRC value of 0.50 (Minimum), light reflection > 85%, non-combustible as per B.S. 476 (Part-IV), 100% humidity resistance and also having thermal conductivity < 0.043 w/mK.] |
| 131 | Providing and fixing G.l. clip in Metal Ceiling System of 600x600 mm module which includes providing and fixing 'C' wall angle of si ze 20x30x20 mm made of 0.5 mm thick pre-painted steel along the perimeter of the room with help of nylon sleeves and wooden screws a t 300 mm center to centre, suspending the main 'C' carrier of size 10x38x10 mm made of G.I steel 0.7 mm thick from the soffit with h elp of soffit cleat 37x27x25x1.6 mm, rawl plugs of size 38x12 mm and 'C' carrier suspension clip and main carrier bracket at 1000 mm centre to centre. Inverted triangle shaped Spring Tee having height of 24 mm and width of 34 mm made of G.l. steel 0.45 mm thick is then fixed to the main 'C' carrier and in direction perpendicular to it at 600 mm centers with help of suspension brackets. Whereve r the main 'C' carrier and spring 'T' have to join, 'C' carrier and spring 'T' connectors have to be used. All sections to be galvan ized @ 120 gms/sq.m. (both side inclusive), fixing with clip in tiles into spring 'T' with : |
| 132 | G.I. Metal Ceiling Clip in plain Beveled edge global white color tiles of size 600x600 mm and 0.5 mm thick with 25 mm height, made o f G.I. sheet having galvanizing of 100 gms/sq.m. (both sides inclusive) and 20% perforation area with 1.8 mm dia. holes and having N RC of 0.5, electro-statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation. |
| 133 | \\"Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflectio n > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the rat io of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rub bing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same m anner.\\" |
| 134 | Providing and applying two coats of High Albedo paint having minimum Solar Reflective Index (SRI) 108 (with solar reflectance & ther mal emittance tested as per ASTM) C 1549 and ASTM C 1371 respectively), VOC less than 10 cc/gm. The coating thickness and the method ology of application shall strctly as per manufacturer's specifications and as approved by Engineer-in-Charge. Surface preparation i ncludes cleaning with metal wire brush to remove all dust, fungus etc., washing with water all complete. The contractor shall give g uarantee for the perfomance of SRI and also the durabitity of coating, all complete as per direction of Engineer-in-Charge. |
| 135 | \\"Polylam Modular Baffle Ceiling system: POLYLAM® is vertical & horizontal baffle system, exhibiting space-delineating characteristic s. The system comprises baffles 40mm wide & 150 Deep thickness of minimum 0.5mm GMS, installed at 150mm C/C . Baffle to be perforate d having acoustic fleece pasted from inside. The C shaped shaped carrier rails run perpendicular to the main baffles profiles. Indiv idual baffle lengths between 300 and 2400 mm can be selected. Baffle are supplied with the end cap matching the similar finish of ba ffle. Tolerances according to TAIM, DIN EN 13964 and quality controlled to ISO 9001:2015 approved by SIS. Substructure for POLYLAM® Vertical baffle system consisting of C shape carrier of minimum 1.2mm thick installed perpendicularly to baffles, same was hanged to wall with the help of wall anchor fasteners. Baffles to be connected perpendicular to C shaped carriers with the help of baffle han ger brackets. The primary profiles must be connected to one another with longitudinal splice connectors. C shaped baffle carriers to be installed at maximum distance of 1200mm. in a length of 2400 mm baffles. Baffle width: 40mm Baffle height: 150 mm Individual baf fle lengths: Min.300/Max.2400mm Material: Minimum 0.5 mm GMS. Surface: Selected Digitally printed Woodgrain finish having minimum 80 micron paint thickness. Manufacturer shall have the fully automatic powder coating system with power and free conveyorize 3mtr/minute capacity. Powder coati ng plant shall be equipped with latest modern technology with fully automatic inline Pre-treatment using nano technology, Inline aut omatic water Drying system after pre-treatment. Mode of Measurements: Measurements shall be wall to wall without any deductions for lights, diffuses, columns etc\\" |
| 136 | Providing, supplying, erecting and fixing in position 3 mm thick polycarbonate sheets of approved texture and colour for roof lighti ng. Sheets to be profiled to match metal sheets described in respective item above. Cost to include jointing, sealing with Butyl adh esives and tapes as per manufacturers specifications and all labour, tools, plants, temporary works, etc. all complete. |
| 137 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charg e) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-c harge. The sheet shall be fixed using self drilling / self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pit ch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 138 | Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+ 0.05 %) total coated thickness, Zinc coating 12 0 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15 -18 microns using self drilling/ self tapping screws complete : |
| 139 | Ridges plain (500 - 600mm) |
| 140 | Flashings/ Aprons.( Upto 600 mm) |
| 141 | 12 mm cement plaster of mix : |
| 142 | 1:6 (1 cement: 6 coarse sand) |
| 143 | 15 mm cement plaster on rough side of single or half brick wall of mix : |
| 144 | 1:6 (1 cement: 6 coarse sand) |
| 145 | 20 mm cement plaster of mix : |
| 146 | 1:4 (1 cement: 4 coarse sand) |
| 147 | 12 mm cement plaster finished with a floating coat of neat cement of mix : |
| 148 | 1:3 (1 cement : 3 fine sand) |
| 149 | 6 mm cement plaster of mix 1:3 (1 cement : 3 fine sand) |
| 150 | Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers [Note: Unit \\"BAG\\" shall mean \\"PER BAG OF 50 KG CEMENT USED IN THE MIX\\"). |
| 151 | Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. |
| 152 | Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth comple te. |
| 153 | Finishing walls with textured exterior paint of required shade :New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and incl uding priming coat of exterior primer applied @ 2.20kg/10 sqm |
| 154 | Finishing walls with ready mixed Premium acrylic emulsion paint (Company Depot Tinted) having VOC less than 50 gm/litre and UV resis tance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade with silicon additives: New work (Two or more coats applied @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm . |
| 155 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wa ll surface to prepare the surface even and smooth complete. |
| 156 | Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound) content : |
| 157 | With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less than 50 grams/ litre. |
| 158 | With water thinnable cement primer on wall surface having VOC content less than 50 grams/ litre. |
| 159 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work |
| 160 | Melamine polishing on wood work (one or more coat). |
| 161 | Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm. depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re roller inclu ding making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth lead upto 50 metres. |
| 162 | Supplying and stacking at site : |
| 163 | Good Earth |
| 164 | Extra for compaction of earth work in embankment under optimum moisture conditions to give at least 95% of the maximum dry density ( proctor density). |
| 165 | Construction of granular sub-base by providing close graded material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thicknes s with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per s pecifications and directions of the Engineer-in-Charge : |
| 166 | With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30 |
| 167 | Providing and laying design mix reinforced cement concrete of M-30 grade in roads/ taxi tracks/ runways, using cement content as per design mix, using coarse sand and graded stone aggregate of 40 mm nominal size in appropriate proportions as per approved & specifi ed design criteria, providing dowel bars with sleeve/ tie bars wherever required, laying at site, spreading, levelling to required s lope/ camber and compacting mechanically by using screed board vibrators, vaccum dewatering process and finally finishing in require d texture by floating & brooming with wire brush, including steel form work with sturdy M.S. channel sections, curing, making provis ion for contraction/ expansion, construction & longitudinal joints (10 mm wide x 50 mm deep) by groove cutting machine, providing ex pansion joints as per drawing including dowel cap, sponge, sealing tape, bitumen painting, debonding tape and filling joints with ap proved joint filler and sealants, complete all as per direction of the Engineer-in-Charge. [Notes: (1) Item of joint fillers, sealan ts, dowel bars with sleeve/ tie bars to be paid separately. (2) The item rate is inclusive of cost of dowel cap, sponge, sealing tap e, bitumen painting, debonding tape. (3) Cement content considered in M-30 is @ 340 kg/cum. Excess/ less cement used as per design m ix is payable/ recoverable separately]. |
| 168 | Cement concrete manufactured in automatic batching plant (RMC plant) including transportation to site in transit mixer |
| 169 | Extra for providing and mixing hardening compound of approved quality as per manufacturer's specification in cement concrete. |
| 170 | Providing and fixing pre-moulded joint filler in expansion joints of RCC roads / CC pavements after making the joints dust free with high pressure air jet cleaners, all complete as per direction of the Engineer-in-Charge. (Pre-moulded joint fillers shall be made o f bitumen hot sealing compound impregnated fibre board having impregnation more than 35%, conforming to IS:1838 for fibre board and IS: 1834 for hot sealing bitumen compound grade A.) [Note: Unit \\"CM\\" shall mean \\"PER CENTIMETRE DEPTH PER CENTIMETRE WIDTH PER METRE LENGTH\\"]. |
| 171 | Providing and filling in position rubberized bitumen hot sealing compound for sealing of expansion joints in roads / pavements all c omplete as per direction of the Engineer-in-Charge. [Note: Unit \\"CM\\" shall mean \\"PER CENTIMETRE DEPTH PER CENTIMETRE WIDTH PER METRE LENGTH\\"]. |
| 172 | Painting road surface marking with adequate nos of coats to give uniform finish with ready mixed road marking paint conforming to IS :164, on bituminous surface in white/ yellow shade, including cleaning the surface of all dirt, scales, oil, grease and foreign mate rial etc. complete : |
| 173 | New work (Two or more coats) |
| 174 | Providing, laying and making kerb channel 30 cm wide and 50 mm thick with cement concrete 1:3:6 (1 cement: 3 coarse sand:6 graded st one aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted wi th fine sand, including finishing the top smooth etc. complete and as per direction of Engineer-in-charge. |
| 175 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thi ckness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc . as per directions of the Engineer-in-Charge. [Notes: (1) Length of finished kerb edging shall be measured for payment. (2) Precast C.C. kerb stones shall be approved by the Engineer-in-Charge.] |
| 176 | Providing and laying factory made chamfered edge interlocking Cement Concrete paver blocks in foot path, park & lawns driveway or li ght & traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in req uired colour & pattern over 50mm thick compacted bed of course sand, compacting and proper embedding/laying of inter locking paver b locks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, all complete as per manufacturer's specifications & directions of the Engineer-in-Charge : |
| 177 | 60mm thick Cement Concrete paver block of M-35 grade with approved colour, design & pattern. |
| 178 | Supplying and stacking at site dump manure from approved source, including carriage upto 5 km complete (manure measured in stacks wi ll be reduced by 8% for payment) : |
| 179 | Screened through sieve of I.S. designation 16 mm |
| 180 | Screened through sieve of I.S. designation 4.75 mm |
| 181 | Fine dressing of the ground. |
| 182 | Spreading of sludge, dump manure and/or good earth in required thickness including removal of debris/ un-wanted material, consolidat ion, dressing, levelling and watering etc. complete as per directions of the Engineer-in-Charge. [Note: Cost of sludge, dump manure and/or good earth shall be paid separately under relevant item of SOR]. |
| 183 | Mixing earth and sludge or manure in the required proportion specified or directed by the Engineer-In-Charge. |
| 184 | Grassing with selection No. 1/ Doob grass including watering and maintenance of the lawn for 30 days or more till the grass forms a thick lawn, free from weeds and fit for mowing including supply and filling of good earth, if required during maintenance period. [N ote: The grass and good earth shall be paid for separately under relevant item of SOR] : |
| 185 | With grass Turf |
| 186 | Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20% : one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, fillin g with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared u nserviceable and surplus earth by spreading and leveling as directed, within a lead of 50 m, lift up to 1.5 m complete (cost of slud ge, manure or extra earth to be paid for separately) |
| 187 | Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by vo lume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or ex tra good earth if needed to be paid for separately) : |
| 188 | Holes 1.2 m dia and 1.2 m deep |
| 189 | Holes 90 cm dia, and 90 cm deep |
| 190 | Holes 60 cm dia, and 60 cm deep |
| 191 | Holes 45 cm dia, and 45 cm deep. |
| 192 | Providing and fixing M.S. flat iron tree guard 60 cm dia and 2.0 m high, above ground consisting 4 Nos. 25x6 mm, 2.25 m long and 8 N os 25x3 mm, 2.0 m long vertical M.S. flats, riveted to 3 nos 25x6 mm M.S. flat iron rings in two halves, fixing together at site wit h required six numbers of 8 mm dia and 30 mm long bolts, including painting two coats with synthetic enamel paint of approved brand and manufacture over a coat of primer. One name plate of 1 mm thick M.S. sheet of size 250x100 mm shall be welded to the tree guard near the middle height and lettered IOCL or any other approved name. The tree guard shall be suitably fixed to the ground by embeddi ng four legs of tree guard in pits of suitable dia and to a depth of 25 cm, refilling the pits with soil and ramming, complete in al l respect as per satisfaction and direction of the Engineer-in-Charge. |
| 193 | Providing and fixing M.S. tree guard 45 cm square in plan, height 1.20 metre above ground level and 0.40 metre below ground level. T he vertical members shall consist of 4 Nos angle iron of size 25x25x3 mm, 1.6 m long, one at each corner and 8 Nos flat iron of size 25x3 mm, 1.2 m long. The vertical mambers shall be welded to 4 Nos. 25x6 mm M.S. flats placed horizontally around the vertical memb er of the cage. One name plate of 1 mm thick M.S. sheet of size 250x100 mm shall be welded to the tree guard near the middle height and lettered IOCL or any other approved name. The tree guard shall be fixed to the ground by making suitable holes and by embedding four corners leg in the ground, including refilling the earth, compaction etc. complete. The tree guard shall be painted with two or more coats of synthetic enamel paint of approved brand and manufacture over a coat of primer, complete in all respect. |
| 194 | Providing Circular Cement Concrete pots of specified size, cast with cement concrete of nominal mix 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 6 mm nominal size), reinforced with 7 Nos (3 Nos horizontal & 4 Nos vertical “U“ shape) M.S. wires of 3.5 m m dia as per design, including required form work, finishing with cement punning on exposed surface, curing for specified period and stacking in required rows & height, all complete as per direction of the Engineer-in-Charge. |
| 195 | Top inside diameter 35 cm, outer bottom diameter 25 cm, total height 35 cm |
| 196 | Top inside diameter 30 cm, outer bottom diameter 20 cm, total height 30 cmwith wall thickness of 25.4 mm |
| 197 | Providing and laying Neelgiri/ Mexican grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level an d ramming with tools wooden (Dhurmos) and than rolling the surface with light roller make the surface smoothen and light waterning w ith sprinkler and maintenance for 30 days or more till the grass establish properly, complete as per direction of the Engineer-in-Ch arge. |
| 198 | Renovating lawns including weeding, cheeling the grass, forking the ground, top dressing with sludge or manure, mixing the same with forked soil, watering and maintaining the lawn for 30 days or more till the grass forms a thick lawn free from weeds and fit for mo wing and disposal of rubbish as directed, including supplying good earth if needed but excluding the cost of sludge or manure. [Note : The good earth shall be paid for separately under relevant item of SOR]. |
| 199 | Cutting of designer hedge/ edge including removing of cut material, cleaning, hoeing of hedge/ edge, bed watering, manuring and appl ying insecticides and fungicides etc. (excluding the cost of materials) complete as per directions of the Engineer-in-Charge. [Note: Unit \\"SQM\\" shall mean \\"PER SQM PER MONTH\\".] |
| 200 | Providing & fixing of White River (Stone) Pebbles size of 2\\" to 2.50\\" dia in natural colour at site of work including loading, unloa ding, carriage and all taxes paid etc.and as per directions of the Engineer-in-Charge. |
| 201 | Anti-termite treatment of infected trees including all branches/ leaves by spraying chemical emulsion (Chlorpyriphos 20% EC 0.5% con centration) through power spray machine @ 100 ml Chlorpyriphos per tree including cost of chemical, complete as per directions of th e Engineer-in-Charge. [Note: Unit \\"EA\\" shall mean \\"EACH TREE\\"]. |
| 202 | Anti-termite treatment of lawn area using PREMISE 30.50% IP. One litre PREMISE diluted in 499 litres of water and applying solution @ 1.00 litre per sqm of lawn or bed area (two applications are required) including cost of chemical complete as per directions of th e Engineer-in-Charge. |
| 203 | Plantation of Trees, Shrubs and Hedges at site including watering and removal of unserviceable materials as per direction of the Eng ineer-in-Charge (excluding cost of plant & water): |
| 204 | Tree Plant |
| 205 | Shrub Plant |
| 206 | Hedge Plant/ Ground Cover |
| 207 | Providing and watering of Horticulture features i.e. lawn, tree, shrubs, hedge/ edge, ground cover etc. with irrigation water at the site of work. Watering shall be done through water tanker having 5000 litre capacity with one labour for watering including cost of water, filling of tanker, watering at site with all leads and lifts as per direction of the Engineer-in-Charge. [Note: Unit \\"EA\\" sh all mean \\"PER TRIP\\"]. |
| 208 | Rose Plants |
| 209 | Providing and Displaying plants Budded Rose (H.T. variety) 3 to 4 healthy branch 30 cm and above ht. well developed with one and abo ve flower plant in 20 cm Earthen Pot, as per direction of the officer-in-charge. |
| 210 | Providing and Displaying plants Creeper Rose variety 3 to 4 healthy branch 60 cm and above ht. well developed with one and above flo wers in 25 cm Earthen Pot, as per direction of the officer-in-charge. |
| 211 | Providing and Displaying plants Standard Rose (H.T. variety) 3 to 4 healthy branch 90 cm and above ht. well developed with one and a bove flowers in 25 cm Earthen Pot, as per direction of the officer-in-charge. |
| 212 | Ornamental Plants |
| 213 | Providing and Displaying Acalypha plant Different colour well developed, fresh & healthy with good foliage, multi branch 30 to 45 cm ht. in 20 cm size of Earthen Pot/ Plastic Pot bushy plant as per direction of the officer-in-charge. |
| 214 | Providing and Displaying Acalypha red plant well developed with fresh & healthy 30 to 45 cm ht. in 20 cm size Earthen Pot/ Plastic P ot as per direction of the officer-in-charge. |
| 215 | Providing and Displaying Ficus reginold piller type Topiary plant well developed with fresh & healthy 210 to 240 cm ht in 40 cm Ceme nt Pot as per direction of the officer-in-charge. |
| 216 | Providing and Displaying Bougainvillea named variety, Sobhra, Thima, Marry palmar, Cherry Blossom etc. well developed with fresh & h ealthy bushy plant in full bloom 75 to 90 cm ht. in 40 cm Cement Pot as per direction of the officer-in-charge. |
| 217 | Providing and Displaying Ficus Long Island topiary plant well developed with fresh & healthy 5 to 6 ball specific size and shape 120 to 150 cm ht in 40 cm Cement Pot as per direction of the officer-in-charge. |
| 218 | Ground Covers Plants |
| 219 | Providing and Displaying of Clerodendron inerme plant of ht. 30 cm to 40 cm multi branched in 25 cm size of Earthen Pot / Plastic Po t & as per direction of the officer-in-charge. |
| 220 | Providing and Displaying of Iresine herbstii plant, of height 20-30 cm., full of branches well developed in 20 cm size of Earthen Po t / Plastic Pot & as per direction of the officer-in-charge.. |
| 221 | Providing and Displaying of Wadelia trilobata plant,full of leaves in 15 cm size of Poly bags & as per direction of the officer-in-c harge. |
| 222 | Tree Plants |
| 223 | Supply and stacking of Alstonia scholaris plant of height 150-165 cm. in bag of size 25 cm as per direction of the officer-in-charge . |
| 224 | Supply and stacking of Bauhinia blakeana (Kachnar) plant of height 120- 150 cm. in big poly bags of size 25 cm as per direction of t he officer-in-charge. |
| 225 | Supply and stacking of Ficus benjamina (green) plant of height 150-165 cm., bushy with healthy branches and lush green foliage in bi g size HDPE bags as per direction of the officer-in-charge. |
| 226 | Supply and stacking of Ficus religiosa (Peepal) plant of height 150-165 cm. in big poly bags of size 30 cm as per direction of the o fficer-in-charge. |
| 227 | Supply and stacking of Nauclea cadamba (Kadam) plant of height 150-165 cm. in big poly bag of size 25 cm as per direction of the off icer-in-charge.v |
| 228 | Supply and stacking of Plumeria acutifolia plant of height 150-165 cm. with 3-4 branches in big size HDPE bag as per direction of th e officer-in-charge. |
| 229 | Supply and stacking of Washingtonia filifea palm plant stem ht. 120-135 cm with 8-10 healthy leaves lush green leaves well developed in big size HDPE Bags as per direction of the officer-in-charge. |
| 230 | SHRUBS |
| 231 | Supply and stacking of plant Caesalpinia pulcherrima species of height 45-60 cm. in earthen pot of size 20 cm as per direction of th e officer-in-charge. |
| 232 | Supply and stacking of plant Calliandra hybrida of height 105-120 cm., well branched, bushy in big size HDPE bag as per direction of the officer-in-charge. |
| 233 | Supply and stacking of plant Hamelia patens of height 30-45 cm. with 3-4 branches in poly bags of size 20 cm as per direction of the officer-in-charge. |
| 234 | Supply and stacking of plant Hibiscus rosasinensis of height 45-60 cm. with 3-4 branches in earthen pots of size 20 cm as per direct ion of the officer-in-charge. |
| 235 | Supply and stacking of plant Tabernaemontana coronaria (Chandni single) of height 90-105 cm,bushy in big size HDPE bag as per direct ion of the officer-in-charge. |
| 236 | Supply and stacking of plant Tecoma gaudichaudi of height 90-105 cm.,bushy in big size HDPE bag as per direction of the officer-in-c harge. |
| 237 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides wi th required PVC/neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed echanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. Glazing and paneling to be paid for separately) : |
| 238 | For fixed portion. |
| 239 | Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 240 | For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittin gs wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) |
| 241 | Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 242 | Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS : 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless ste el screws etc. complete as per architectural drawings and directions of engineer-in-charge. |
| 243 | Pre-laminated particle board with decorative lamination on both sides |
| 244 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber/ neoprene gasket et c. complete as per the architectural drawings and directions of the Engineer-in-Charge. [Note: Cost of aluminium snap beading shall be paid in basic item] : |
| 245 | With float glass panes of 5.50 mm thickness |
| 246 | With float glass panes of 8.00 mm thickness |
| 247 | With clear toughened glass panes of 6 mm thickness |
| 248 | With clear toughened glass panes of 8 mm thickness |
| 249 | Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and directions of the Engineer-in-Charge complete : Up to 5 mm depth and 5 mm width |
| 250 | Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and f ixing top & bottom pivot & double action hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing r equired door fittings, all complete as per directions of the Engineer-in-Charge. [Note: Door handle, lock and stopper etc.to be paid separately]. |
| 251 | Providing and fixing self adhesive type frosted glass film of 3M make or approved equivalent, in required pattern over glass etc. a s per drawings, including cleaning the receiving surface of glass etc., all complete as per manufacturer's specification and direct ion of Engineer in charge: |
| 252 | Plain frosted film |
| 253 | Colored frosted film |
| 254 | Providing and fixing 12mm thk. Toughened float glass glazing cut and fixed in openings of desired shape as per drawing with 3/4\\" bev eling all around, fixed with the help of SS patch fittings, with top and bottom 'C' channels, fixed firmly to the slab/ MS Structure ,as directed by Engineer in Charge. Area of openings to be measured). Assume frameless glass. Rate of above item to include P/F of : 20x20mm \\"C\\" channel SS patch Fittings. |
| 255 | \\"Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474, including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. ( The item includes cost of material su ch as cleats, sleeves, fasteners screws etc as desired. necessary for fabrication of extruded aluminium frame work. Nothing extra sh all be paid on this account). The weight of aluminium extruded section shall be taken for purpose of payment.\\" |
| 256 | Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural/ curtain wall glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including : a) Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)-cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalization & drainage and protection against fire hazard b) Fabricating and supplying serrated M.S. hot dip galvanized / Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3 Dimensional movement for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry/structural steel framework of building structure using stainless steel anchor fasteners/ bolts, nylon separator to prevent bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers.. c) Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of required bite size in a clean and controlled factory / work shop environment , including double sided spacer tape, setting blocks and backer rod, all of approved grade, brand and manufacture, as per the approved sealant design, within and all around the perimeter for holding glass d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site conditions, to seal the gap between the building structure and all its interfaces with curtain glazing to make it watertight. e) Making provision for drainage of moisture/ water that enters the curtain glazing system to make it watertight, by incorporating principles of pressure equalization, providing suitable gutter profiles at bottom (if required), making necessary holes of required sizes and of required numbers etc. complete. This item includes cost of all inputs of designing, labour for fabricating and installation of aluminium grid, installation of glazed units, T&P, scaffolding and other incidental charges including wastages etc., enabling temporary structures and services, cranes or cradles etc. as described above and as specified. The item includes the cost of getting all the structural and functional design including shop drawings checked by a structural designer, dully approved by Engineer-in-charge. The item also includes the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working structural glazing as specified, cleaning and protection till the handing over of the building for occupation. In the end, the Contractor shall provide a water tight structural glazing having all the performance characteristics etc. all complete as required, as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer in-Charge. Note:- 1. The cost of providing extruded aluminium frames, shadow boxes, extruded aluminium section capping for fixing in the grooves of the curtain glazing and vermin proof stainless steel wire mesh shall be paid for separately under relevant items under this subhead. However, for the purpose of payment, only the actual area of structural/ curtain wall glazing (including width of grooves ) on the external face shall be measured in sqm. up to two decimal places. |
| 257 | Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened (as approved) glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner heat strengthened (as approved) clear float glass 6mm thick, spacer tube 12mm wide, desiccants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor. (Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.1.8.16 above). For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm. (To be fixed on extruded aluminium sections. and cost of aluminium sections to be paid in relevant item) (i) Coloured tinted float glass 6mm thick Heat Strengthened substrate with reflective soft coating on face # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. |
| 258 | Extra for openable side / top hung vision glass panels (IGUs/laminated glass) including providing and supplying at site all accessor ies and hardware for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, m in 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fast eners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer in- Charge.. |
| 259 | Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the lik e consisting of : (a) First course of applying cement slurry @ 4.4 Kg/sqm mixed with water proofing compound conforming to IS:2645 in recommended proportions including rounding off junction of vertical and horizontal surface. (b) Second course of 20 mm cement pla ster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. (c) Third course of applying blown or residual bitumen applied hot at 1.7 Kg/ sqm of area. (d) Four th course of 400 micron thick PVC sheet. [Note: Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 Kg/sqm]. |
| 260 | Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin-charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge : \\"With average thickness of 120 mm and minimum thickness at khurra as 65 mm.\\" |
| 261 | Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like r etaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels/ subway and bri dge deck etc., prepared by mixing in the ratio of 5:2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces an d 3:1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) si de with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressur e on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be car ried out all complete as per specification and directions of the Engineer-in-Charge. The product performance shall carry guaranteed for 10 years against any leakage : |
| 262 | For vertical surface two coats @ 0.70 kg per sqm per coat |
| 263 | For horizontal surface one coat @ 1.10 kg per sqm |
| 264 | Providing and fixing certified restroom cubicle system of approved make comprising of green guard certified solid compact laminated water proof board, minimum 18 mm thick made as per IS: 2046 (phenolic core board) and as per BS-476/97 for fire retardant for toilet showers, water closet etc . The board shall be manufactured under high pressure and temperature by impregnating kraft papers and outer decorative papers with thermosetting phenolic/ melamine resins (low VOC). The cubicle system shall be resistant towards water, chemical, scratch, impact and heat and shall be anti bacterial, colour fast and shall have accessories like door knob, Gravity/ auto return hinges, privacy thumb turn with occupancy indicator, coat Hook, etc all in SS 304. The hardware and fixings includes anchoring of all fixed front panel to floor with SS 316 L brackets/ base plates with a clearance height upto 110 mm, and covered with SS 316 Shoe box plates, wall and corner joineries (brackets and channels) shall be SS 304 grade, SS 304 screws, rubber noise reduction tape . The cubicle unit shall be installed in approved finish, shades and colours as per specifications and directions of Engineer-In-Charge, including minimum 5 (five) years warranty against any moisture related damages to all intermediate panels, doors, hardqwares etc. Standard dimension of the cubicle system shall be of approx. 2100 mm Height(overall) x 1500mm Depth and 1000 mm Width which includes 600mm door size width. |
| 265 | I shaped Cubicle System consisting of front face panel including door and all necessary accessories, fittings and hardware etc. |
| 266 | L shaped Cubicle System consisting of front face panel including door, intermediate panel and all necessary accessories, fittings an d hardware etc. |
| 267 | Manual Roller Blinds |
| 268 | Supplying and installing roller blinds of approved make, model and shade at all heights and location and required width and comprising of approved shade and quality fabric, 1 mm thick anodized extruded Aluminium alloy roller tube of 38-mm O.D , a bidirectional operating Clutch mechanism designed for adjustment-free, slippage-free, crash proof smooth operation for all heights, high strength fiber glass reinforced polyester idler, powder coated steel Insert type brackets fitted with roller tube, round bottom rail, control unit engrooved with a Ball Pitch of minimum 6.5mm, Stainless Steel Ball Chain, and powder coated atomized steel installation brackets. The clutch mechanism comprises of a SS beaded chain and carbon steel spring wrapped by means of a high strength fiber glass reinforced polyester assembly to transmit motion from driving to driven members. The installation brackets shall facilitate overhead, side or face mounting with clutch assembly on either end of the roller. Idler shall consist of a centre shaft and outside sleeve which provide bearing surface for roller tube and rotate freely on centre shaft for smooth and quiet operation. Bottom rail along with the fabric shall be enclosed in a suitably created pocket and shall be of powder coated aluminium tube and closed from sides with end caps. The item includes all fittings, accessories, brackets, screws, anchor fasteners, fabric as per approved sample and shade all complete as per drawings, tender specifications, relevant standards and direction of Engineer in charge. (Height of blind from top bracket to bottom tube and width from bracket to bracket shall be measured for payment) Manual Roller Blinds with following specification: Composition- 30% Polyester (max),70% PVC on Polyester(min), Openness factor- 3-5%(as approved) Weight (gram/ sqm)- min 440 gm/sqm Thickness- min 0.60 mm Fire Classification- Class A( NFPA 101 or Class 1 (UNE EN 13773) or equivalent as per relevant standards and specifications Fastness to light- 6-7/8 or higher Indoor Air Quality- GreenGuard / Eco-Codice Certified. Manufacturer's warrantee- minimum 5 years |
| 269 | Providing and fixing Glass Reinforced Concrete (G.R.C) Screen at all levels & heights in approved size, pattern, design, thickness ( minimum 35mm) and color. The Screens should be made from White Portland Cement, Quartz, Fine Silica Sand, Alkali Resistant Glass Fib er, Super Plasticizers, Polymers and U.V resistant Synthetic inorganic pigments should be used for pigmentation. The material castin g should take place in Synthetic Rubber / FRP Mould. The fixing of Jali should be ‘Dry fixing’ i.e. to be done with MS/SS ‘L’ shaped Clamps, dash fasteners and pins etc complete as per site requirment and direction of Engineer-in-charge. |
| 270 | Plumbing, STP, Rainwater Harvesting Work |
| 271 | Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including c ollecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all eq uipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, upto 90 metre dept h below ground level. |
| 272 | All types of soil |
| 273 | 400 mm dia |
| 274 | Rocky strata including Boulders |
| 275 | 400 mm dia |
| 276 | Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC (Slotted / Plain pipe) medium well c asing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. al l complete, for all depths, as per direction of Engineer -in-charge |
| 277 | 200 mm nominal size dia |
| 278 | Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with r ibs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per dire ction of Engineer-in-charge. |
| 279 | 200 mm nominal size dia |
| 280 | Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. |
| 281 | Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulde rs, in required thickness, for all leads & lifts, all complete as per direction of Engineer-incharge. |
| 282 | Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness ove r gravel layer, for all leads & lifts, all complete as per direction of Engineer -in-charge. |
| 283 | Gravel packing in Rainy well construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineerin- charge. |
| 284 | Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I). |
| 285 | 200 mm dia |
| 286 | Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality. |
| 287 | EHD-35 |
| 288 | Circular shape 560 mm internal dia |
| 289 | Sewage Treatment Plant 10 KLD MBBR Based Under ground RCC Tanks Sewage treatment plant-MBBR technology ( with air diffuser system) with sewage handling capacity of 10 KL per day. The raw sewage collection sump with double SS bar screen shall be part of STP. STP shall be designed as water retaining structure, . Including necessary chemical dosing as required by the manufacturer's design. All the equipments, pipings, pumps, blowers and electricals are to be housed in a plant room at Ground level. Including GI Puddle flanges (with hot dip galvanizing) inlet,outlet, overflow, vent, C.I. Manhole covers, drain channels with MS(painted) gratings.Contractor to exclude all civil works like construction of equalization tank,civil works for pump room ,etc.All STP compartments(except equalization tank),pumps ,equipments shall be placed Above Ground level. Construction of Underground RCC STP Tanks is not in the scope of work of STP contractor. The STP shall be designed based on the following parameters: for irrigation purpose. Flow Rate - 35 KL/day-MBBR technology pH - 7-9 BOD - 250 - 300 mg/lt. COD - upto 600 mg/lt. SS - upto 400 mg/lt. Oil ,Grease and ABS - upto 75 mg/lt. Ecoli MPN/100ML - 1000000 The treated sewage shall have following characteristics: pH - 7.0 - 7.5 BOD -less than 30 mg/lt. COD -less than 50 mg/lt. SS - Less than 20 mg/lt. Oil & Grease and ABS - less then 5mg/lt. Ecoli MPN/100ML - 1000 |
| 290 | Bar Screen Size : 600 x 800 MOC : SS 304 Qty : 01 Nos |
| 291 | Raw Sewage Transfer Pumps Flow rate (each) = 2000 lph Head = 10 Mtr Qty = 02 Nos (1W + 1SB) Make:- Kirloskar, Lubi,Leo or equivalent |
| 292 | Sludge Re-circulation Pumps Flow rate (each) =2000 lph Head = 8 Mtr Qty = 01 Nos (1W + 1SB) Make:- Kirloskar, Leo, Lubi or equivalent |
| 293 | Sump Pumps for plant room drainage Flow rate (each) =3500 lph Head = 10 Mtr Qty = 02 Nos (1W + 1SB) Make:- Kirloskar, Leo, Lubi or equivalent |
| 294 | Centifuse Feed Pump Flow rate (each) = 2000 lph Head = 20 Mtr Qty = 02 Nos ( 1W + 1SB) Make:- Kirloskar, Leo, Lubi or equivalent |
| 295 | Air diffusion system :(Air Blower) |
| 296 | 2 Nos. (one working & one standby) capable of delivering 125 m3 of free air each at 4500 MMWG driven through “V” belt or directly coupled through flexible coupling to a TEFC motor of suitable HP suitable for 415 ± 10% volts, 3 phase, 50 cycles A.C. supply.- 1 Set. Make : Beta, Airwack or equivalent |
| 297 | UPVCI/MS(heavy Class) conforming to IS:1239- 1982 complete with UPVC fittings ® brand such as tees, crosses, |
| 298 | Flexible pipes complete with stainless steel fittings such as tees, crosses, plugs, sockets, elbows, reducers, supports & clamps, puddle flanges etc cutting chases & making good for submerged air piping. |
| 299 | Air Distribution Systems |
| 300 | Membrane Air Defuser, Disc Type Pipe line and related accessories |
| 301 | Centrifuge Basket for Sludge Management & disposal. |
| 302 | Filter Feed Pumps Flow rate (each) = 2000 lph Head = 30 Mtr Quantity = 02 Nos (1W / 1S) Make:- Kirloskar, Leo, Lubi or equivalent |
| 303 | Multigrade Filter |
| 304 | Supplying, installing, testing and commissioning of tertiary treatment systems comprising of a MSEP pressure sand multigrade filte r(shell 6mm & dished ends 8mm)with Frontal Piping, 5 Valve Battery. Filters shall be suitable for flow rate of 10000 LPH at 3.5 K g/Sqcm working pressure. |
| 305 | Activated Carbon Filter |
| 306 | Supplying, installing, testing and commissioning of tertiary treatment systems comprising of a MSEP Activated Carbon filter (shell 6mm & dished ends 8mm)with Frontal Piping, 5 Valve Battery. Filters shall be suitable for flow rate of 10000 LPH at 3.5 Kg/Sqcm working pressure |
| 307 | MS Header & running pipe UPVC complete with UPVC fittings ® brand such as tees, crosses, plugs, sockets, elbows, reducers, s upports & clamps, puddle flanges etc cutting chases & making good including coating the pipes with desired shade of colour coding over a coat of primer piping before tertiary treatment. - 1 Set. (Make Supreme/prince). |
| 308 | MBBR Media |
| 309 | Tube Settler Media |
| 310 | PVC Tube Media of 750 mm height . |
| 311 | Supply Installation, testing & commissioning of Electrical Panel suitable for 415 V, 3 Phase, 4 wies, 50Hz power distribution system. The panel shall be free standing floow / wall mounted, sheet metal enclosed flush front dust & venim proof with Aluminium bus bars. The painting shall be done as per relevant ISI codes as specified. Adequate size cable alley shall be provided for each cable bending & termination. (All components would be L&T/Schnieder /GE). Including electrical wiring for electrical connection of equipments.with cable trays ets.complete. |
| 312 | U.F Systems |
| 313 | \\"Providing & fixing Skid Mounted ultra filtration System For Flushing Water \\" |
| 314 | Chlorine Doser:- |
| 315 | Supply, installation, testing & commissioning of chlorine dosing system consisting of one FRP/ HDPE tank of 100 liters capacity w ith a positive displacement diaphragm Dosing pump with a variable flow rate of 0-6LPH. The motor shall be suitable for operat ion at 240 V /one phase/ 50 Hertz supply. The pump shall be supplied complete with necessary poly propylene piping, valves, strain ers & injection fittings for system to dose solution to the feed line. The pump shall be Asia LMI make. (Location : Pump Room for ST P). |
| 316 | INSTRUMENTATION Sewage flow Measurement - Electro Magnetic type flow measurement for output Sewage flow. -1nos. Level Switch - Equalisation tank, filter feed tank Sludge holding tank & treated water tank.-4 nos. Make : Electronet or equivalent Online PH meter - Online after ACF-1no. Make : Aster or equivalent Digital Energy meter - Panel Mounted-1no. |
| 317 | Providing & fixing Digital water meter complete with all internal fittings/accessories,making connection with water supply pipe inc luding all fittings on pipes of following diameter. |
| 318 | Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including c ollecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all eq uipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & upto 150 metre depth below ground level. |
| 319 | All Types of Soil |
| 320 | 400mm dia |
| 321 | Rocky strata including boulders |
| 322 | 400mm dia |
| 323 | \\"Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric Resistance Welded) FE 410 mild steel sc rewed and socketed/plain ended casing pipes of required dia, conforming to IS: 4270, of reputed & approved make, including painted w ith outside surface with two coats of anticorrosive paint of approved brand and manufacture, including required hire & labour charge s, fittings & accessories, all complete, for all depths, as per direction of Engineer-in-charge.\\" |
| 324 | \\"200 mm nominal size dia having minimum wall thickness 5.40 mm\\" |
| 325 | \\"Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric Resistance Welded) FE 410 plain slotted (having slot of size 1.6/3.2 mm) mild steel threaded and socketed/ plain bevel ended pipe (type A) of required dia, conforming to I S: 8110, of reputed and approved make, having wall thickness not less than 5.40 mm, including painted with outside surface with two coats of anticorrosive bitumestic paint of approved brand and manufacture, including hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of Engineer -in-charge.\\" |
| 326 | 200 mm nominal size dia |
| 327 | Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. |
| 328 | Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulde rs, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. |
| 329 | Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -in-charge. |
| 330 | Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required gr ading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge. |
| 331 | Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield withou t sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by \\"V\\" notch method or any other approved method, measuring static level & draw down et c. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all com plete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer -in-charge. |
| 332 | Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, remova ble as per requirement, all complete for borewell of: |
| 333 | 200 mm dia |
| 334 | Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including n ecessary bolts & nuts of required size complete. |
| 335 | 200 mm clamp. |
| 336 | Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I). |
| 337 | 200 mm dia |
| 338 | Supply, installation testing & commissioning of submersible pumping set complete in ss suitable to operate on 410 volts 3 phase 50 HZ A.C. power supply, Motor efficiency IE 3 including water proof joint free flat submersible cooper cable,of 6 sqmm including earthing connection motor control panel complete in all respect as per details given below : (For Borewell)(2NOS) Discharge 100 LPM. Head 30 m HP/Load 1HP |
| 339 | SANITARY FIXTURES & FITTINGS |
| 340 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with a ll fittings and fixtures complete, including cutting and making good the walls and floors wherever required |
| 341 | W.C. pan with ISI marked white solid plastic seat and lid |
| 342 | Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, includi ng painting of fittings and brackets, cutting and making good the walls wherever required:- |
| 343 | a) White Vitreous China Wash basin size 630x450 mm with a 15 mm CP Brass single hole basin mixer |
| 344 | \\"Providing and fixing kitchen sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P. brass waste complete, including painting the fittings and brackets, cutting and making good the walls wherever required: \\" |
| 345 | White glazed fire clay kitchen sink of size 600x450x 250 mm |
| 346 | Supply, Receiving, Storing & Fixing of CP brass wall mounted sink mixer with C.P. wall flange, swinging spout complete as required with flow rate of 6.0 LPM complying to Green Building requirements. |
| 347 | \\"Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C . of quality and make as approved by Engineer - in - charge. \\" |
| 348 | Providing and fixing CP Brass 32mm size bottle trap of approved quality & make and as per the direction of engineer in charge. |
| 349 | Providing and fixing toilet paper holder |
| 350 | C.P. brass |
| 351 | Supply, Receiving, Storing & Fixing of C.P. brass twin coat hook with PVC rawl plug & C.P. brass screw complete as required. |
| 352 | \\"Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931. \\" |
| 353 | 15mm nominal bore |
| 354 | \\"Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. \\" |
| 355 | 15 mm nominal bore with 45 cm length |
| 356 | Providing and fixing Chromium Plated towel ring Rectangular shape with concealed fittings arrangement of approved quality and colo ur, of approved brand & manufacture complete as per direction of Engineer in Charge. |
| 357 | Providing and fixing Cp bras liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bra cket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. |
| 358 | \\"Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having p re & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitab le brackets all as per manufacturers specification and direction of Engineer-in-charge. \\" |
| 359 | Providing and fixing 75 mm high, 50 mm deep and 18 mm thick stone slab table rubbed, edges rounded and polished, fixed in urinal par titions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with ceme nt concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth. |
| 360 | Granite Stone of approved shade |
| 361 | Supply and fixing of water cooler fully stainless steel of 60 litres cooling capacity and 120 litres storage capacity to be operated on single phase supply with ISI mark. Each Cooler shall be provide with 4 Nos pessmatic tap for Drinking purpose. |
| 362 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board grou nd fixed to wooden cleats with C.P. brass screws and washers complete. |
| 363 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. |
| 364 | Flexible pipe |
| 365 | 40 mm dia |
| 366 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms . |
| 367 | 15 mm nominal bore |
| 368 | Providing and fixing low flow type two way bib tap as per approved make complete in all respect as per engineer in the charge. |
| 369 | INTERNAL & EXTERNAL WATER SUPPLY |
| 370 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. |
| 371 | Internal work - Exposed on wall |
| 372 | 20 mm dia nominal bore |
| 373 | 32 mm dia nominal bore |
| 374 | 40 mm dia nominal bore |
| 375 | 50 mm dia nominal bore |
| 376 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fi ttings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. |
| 377 | Concealed work, including cutting chases and making good the walls etc. |
| 378 | 15 mm nominal dia Pipes |
| 379 | 20 mm nominal dia Pipes |
| 380 | 25 mm nominal dia Pipes |
| 381 | 32 mm nominal dia Pipes |
| 382 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : |
| 383 | 20mm nominal bore |
| 384 | 25mm nominal bore |
| 385 | 32mm nominal bore |
| 386 | 40mm nominal bore |
| 387 | 50mm nominal bore |
| 388 | Providing and fixing motorized valve with sensor of approved quality, to complete the work. |
| 389 | 40 mm dia ( Flushing Riser) |
| 390 | SOIL, WASTE, VENT PIPES, RAIN WATER PIPES & FITTINGS. |
| 391 | Providing and fixing soil, waste and vent pipes: |
| 392 | 100mm dia pipe |
| 393 | Hubless Centrifugally cast (spun) iron pipes epoxy coated inside and out side IS : 15905 |
| 394 | 75mm dia pipe |
| 395 | Providing and fixing bend of required degree with access door insertion rubber washer 3mm thick, bolts and nuts complete. |
| 396 | 100 mm dia |
| 397 | Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905 |
| 398 | 75 mm dia |
| 399 | Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905 |
| 400 | Providing and fixing plain bend of required degree: |
| 401 | 100 mm dia |
| 402 | Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905 |
| 403 | 75 mm dia |
| 404 | Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905 |
| 405 | Providing and fixing double equal plain junction of required degree. |
| 406 | 100 x 100 x 100 x 100mm |
| 407 | Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905. |
| 408 | Providing and fixing single equal plain junction of required degree. |
| 409 | 100 x 100 x 100mm |
| 410 | Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905 |
| 411 | 75x75x75 mm |
| 412 | Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905 |
| 413 | Providing and fixing single unequal plain junction of required degree : |
| 414 | 100x100x75 mm |
| 415 | Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905 |
| 416 | Providing and fixing terminal guard |
| 417 | 100 mm |
| 418 | Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905 |
| 419 | Providing and fixing shielded coupling for Hubless centrifugally cast iron pipe |
| 420 | 100 mm |
| 421 | SS 304 grade coupling with EPDM rubber gasket |
| 422 | 75 mm |
| 423 | SS 304 grade coupling with EPDM rubber gasket |
| 424 | Providing and fixing M.S. stays and clamps for sand cast iron/centrifugally cast (spun) iron pipe of diameter: |
| 425 | 100mm |
| 426 | Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cem ent concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cos t of cutting holes and making good the walls etc. : |
| 427 | For 100 mm dia pipe |
| 428 | \\"Providing and fixing G.I. pipes complete with G.I. fittings and clamps,including cutting and making good the walls etc. Internal work - Exposed on waLL.\\" |
| 429 | 32 mm dia |
| 430 | 50 mm dia |
| 431 | Providing and Fixing floor trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, incl uding cost of cutting and making good the walls and floors |
| 432 | 100 mm inlet and 100 mm outlet |
| 433 | Hubless Centrifugally cast (spun) iron pipes epoxy coated inside and out side IS : 15905 |
| 434 | 100 mm inlet and 75 mm outlet |
| 435 | Hubless Centrifugally cast (spun) iron pipes epoxy coated inside and out side IS : 15905 |
| 436 | Providing and fixing G.I clean out plug with G.I socket complete with all necessary fitting complete as required by the engineer-in- charge or consultant |
| 437 | 100 mm dia Pipe |
| 438 | Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggr egate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sa nd) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.450 X 450mm - |
| 439 | Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams. |
| 440 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. |
| 441 | 160 mm diameter (with all fittings) |
| 442 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes con forming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal ex pansion. |
| 443 | Single Push Fit Coupler |
| 444 | 75 mm dia |
| 445 | Single tee without door |
| 446 | 75x75x75 mm |
| 447 | Plain bend 87.5 deg |
| 448 | 75 mm dia |
| 449 | Shoe (Plain) |
| 450 | 75 mm dia |
| 451 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 m m hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 ceme nt : 4 coarse sand) and making good the wall etc. complete. |
| 452 | 75 mm dia |
| 453 | EXTERNAL SEWERAGE AND STORM WATER DRAINAGE |
| 454 | \\"Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bo ttoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as d irected, within a lead of 50 m : All kinds of soil\\" |
| 455 | Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia |
| 456 | Supplying and laying of following size DWC SN8 pipe ISI marked along with all accessories like socket, bend, couplers etc. conformin g to IS 16098, Part II complete with fitting and cutting,jointing etc.direct in ground (75 cm below ground level) including excavati on and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. |
| 457 | 200 mm dia. pipe |
| 458 | Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round DWC pipes including bed concrete as per standard design : |
| 459 | 200 mm dia. DWC & RCC Pipe |
| 460 | 250 mm dia. DWC & RCC Pipe |
| 461 | 300 mm dia. DWC & RCC Pipe |
| 462 | \\"Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing o f joints etc. complete :\\" |
| 463 | 250 mm dia. R.C.C. pipe |
| 464 | 300 mm dia. R.C.C. pipe |
| 465 | Constructing brick masonry manhole in cement mortar 1:4 ( 1cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4coarse sand (z one-III) : 8 graded stone aggregate 40 mm nominalsize), inside plastering 12 mm thick with cement mortar 1:3 (1 cement: 3 coarse san d) finished with floating coat of neat cement andmaking channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : |
| 466 | Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cov er and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : 19.7.1.1 With common burnt clay F.P.S. (n on modular) bricks of class designation 7.5 |
| 467 | Extra for depth for manholes : |
| 468 | Size 90x80 cm |
| 469 | Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design : |
| 470 | 150 x 100mm size P-type |
| 471 | With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 472 | Constructing brick masonry road gully chamber 50x45x60cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x4 50mm precast RCC horizontal grating with frame complete as per standard design. |
| 473 | With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 474 | Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910 on 12mm dia steel bar conformi ng to IS : 1786 having minimum cross section as 23 mmx25mm and over all minimum length 263 mm and width as 165mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring pro jections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as p er specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manhol es with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design. |
| 475 | \\"Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floa ting coat of neat cement and making necessary channels for the drain etc. complete :\\" |
| 476 | For pipes 250 to 300 mm diameter |
| 477 | For pipes 350 to 450 mm diameter |
| 478 | EXTERNAL WATER SUPPLY |
| 479 | Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. |
| 480 | 25 mm dia nominal bore |
| 481 | 32 mm dia nominal bore |
| 482 | 40 mm dia nominal bore |
| 483 | 50 mm dia nominal bore |
| 484 | 65 mm dia nominal bore |
| 485 | Providing and fixing in position garden hydrant hose outlet consisting of 25mm ball valve full bore type with lever and female screw ed ends, tested to 20 Kg/cm2 of approved quality, including G.I. elbow, G.I. threaded hose receiver etc. complete. |
| 486 | Providing and fixing enclosed type water meter (bulk type) conforming to IS : 2373 and tested by Municipal Board complete with bolts , nuts, rubber insertions etc. (The tail pieces if required will be paid separately) : |
| 487 | 80 mm dia nominal bore |
| 488 | Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 grad ed stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded st one aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design : |
| 489 | \\"With common burnt clay F.P.S.(non modular) bricks of class designation 7.5\\" |
| 490 | \\"Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, wi th C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coar se sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :\\" |
| 491 | \\"With common burnt clay F.P.S.(non modular) bricks of class designation 7.5\\" |
| 492 | \\"Constructing masonry Chamber 60x45x50 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for water meter comp lete with C.I. double flap surface box 400x200x200 mm (inside) with locking arrangement and RCC top slab 1:2:4 mix (1 cement : 2 coa rse sand : 4 graded stone aggregate 20 mm nominal size) , i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine s and:10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thic k, finished with a floating coat of neat cement complete as per standard design :\\" |
| 493 | \\"With common burnt clay F.P.S.(non modular) bricks of class designation 7.5\\" |
| 494 | \\"Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality :\\" |
| 495 | 25 mm dia nominal bore |
| 496 | 32 mm dia nominal bore |
| 497 | 40 mm dia nominal bore |
| 498 | 50 mm dia nominal bore |
| 499 | 65 mm dia nominal bore |
| 500 | Providing and filling sand of grading zone V or coarser grade, allround the G.I. pipes in external work : |
| 501 | 25 mm dia nominal bore |
| 502 | 32 mm dia nominal bore |
| 503 | 40 mm dia nominal bore |
| 504 | 50 mm dia nominal bore |
| 505 | 65 mm dia nominal bore |
| 506 | \\"Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) :\\" |
| 507 | 20 mm dia nominal bore |
| 508 | 25 mm dia nominal bore |
| 509 | 32 mm dia nominal bore |
| 510 | 40 mm dia nominal bore |
| 511 | 50 mm dia nominal bore |
| 512 | 65 mm dia nominal bore |
| 513 | Electrical-Internal Works |
| 514 | Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as requir ed. (But without MCB/RCCB/Isolator) |
| 515 | 8 way, Double door |
| 516 | 12 way, Double door |
| 517 | Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthin g etc. as required. (But without MCB/RCCB/ Isolator) |
| 518 | 6 way Double door |
| 519 | 8 way Double door |
| 520 | Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing an d commissioning etc. as required. |
| 521 | 40 amps |
| 522 | 63 amps |
| 523 | Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 524 | 63 amps |
| 525 | 40amps |
| 526 | Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, \\"C\\" curve, miniature circuit breaker suitable for inductive load of fo llowing poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 527 | Single pole |
| 528 | Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required. |
| 529 | Supplying and fixing following rating, four pole, three phase and neutral, 415 volts, residual current circuit breaker ( RCCB), havi ng a sensitivity current upto 30 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc as req uired. |
| 530 | 63 amps |
| 531 | 40amps |
| 532 | Providing and fixing following rating and breaking capacity and pole MCCB with theMomagnetic release and teMinal spreaders in existi ng cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required |
| 533 | 125 A,36KA,FPMCCB |
| 534 | \\"Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single cor e cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. \\" |
| 535 | Group – C |
| 536 | Wiring for group control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed ste el conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper co nductor single core cable etc. as required. |
| 537 | Group – C |
| 538 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class steel conduit as required |
| 539 | 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire |
| 540 | 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire |
| 541 | 2 X 4 sq. mm + 1 X 4 sq. mm earth wire |
| 542 | 2 X 6 sq. mm + 1 X 6 sq. mm earth wire |
| 543 | 2 X 10 sq. mm + 1 X 6 sq. mm earth wire |
| 544 | 4 X 2.5 sq. mm + 2 X 2.5 sq. mm earth wire |
| 545 | 4 X 4 sq. mm + 2 X 4 sq. mm earth wire |
| 546 | 4 X 6 sq. mm + 2 X 6 sq. mm earth wire |
| 547 | 4 x 10 sq.mm + 2 x 6 sq.mm. earth wire |
| 548 | 4 x 16 sq.mm + 2 x 6 sq.mm. earth wire |
| 549 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fix ing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in re sidential buildings). |
| 550 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fix ing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required. |
| 551 | Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top along wi th 20 amps \\"C\\" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let an d complete with connections, testing and commissioning etc. as required. |
| 552 | Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. |
| 553 | Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 2 Nos 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. |
| 554 | Supplying and fixing of call bell / buzzer suitable for single phase,230 volt complete as required. |
| 555 | Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed stee l conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper con ductor single core cable etc. as required. |
| 556 | Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surf ace conduit, or cutting the wall and making good the same in case of recessed conduit as required. |
| 557 | 20 mm |
| 558 | 25 mm |
| 559 | 32 mm |
| 560 | Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sh eet cover in front including painting etc. as required. |
| 561 | 75 mm X 75 mm X 60 mm deep |
| 562 | 100 mm X 100 mm X 60 mm deep |
| 563 | 150 mm X 75 mm X 60 mm deep |
| 564 | 150 mm X 150 mm X 60 mm deep |
| 565 | 200 mm X 125 mm X 60 mm deep |
| 566 | 200 mm X 150 mm X 60 mm deep |
| 567 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. |
| 568 | 5/6 A switch |
| 569 | 15/16 A switch |
| 570 | 3 pin 5/6 A socket outlet |
| 571 | 6 pin 15/16 A socket outlet |
| 572 | Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. |
| 573 | \\"Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as re quired. \\" |
| 574 | 1 or 2 Module (75 mmX75 mm) |
| 575 | 3 Module (100 mmX75 mm) |
| 576 | 4 Module (125 mmX75 mm) |
| 577 | 6 Module (200 mmX75 mm) |
| 578 | 8 Module (125 mmX125 mm) |
| 579 | Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. |
| 580 | 1 or 2 Module |
| 581 | 3 Module |
| 582 | 6 Module |
| 583 | 8 Module |
| 584 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixi ng 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required |
| 585 | Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, \\"C\\" curve including connections, painting etc. as required. |
| 586 | \\"SITC OF Recessed downlight Blaire with HPE (High-PerfoMance Efficiency) with LED (Light Emitting Diode), system power: 18W, Luminou s flux of luminaire 1980lm, Colour temperature of 4000 K, Neutral white, CRI>80, , SDCM<3 , R9>0 , THD<10% 230V constant current dr iver, 70% of luminous flux after 50,000 operating hours; energy-efficient LEDs, direct light emission, housing in pre-cast die alumi nium, Polyester powder-White coloured coat applied over a 5-stage pre-treatment trim,deep recessed Prismatic diffuser for homogenous light distribution, ZHLS (ZERO HALOGEN LOW SMOKE) wiring, electronic control gear. Protection class II, IP 20 Ø = 171 mm, DA(Ø) = 160 mm, H = 59 mm\\" |
| 587 | \\"SITC OF Surface Mounted luminaire Zing with LED (Light Emitting Diode) system power: 12 W, Luminous flux of luminaire 1320 lm, Colo ur temperature of 4000 K, neutral white, CRI > 80, , SDCM<3 , R9>0 , THD<10% 230 V constant current driver, 70% of luminous flux aft er 50,000 operating hours; Energy efficient LEDs, Direct light emission, Luminaire housing in die-cast aluminium, Polyester powde r white coloured coat applied over a 5- stage pre-treatment, Opal protruded diffuser for homogenous light distribution, ZHLS (ZERO H ALOGEN LOW SMOKE) internal wiring, electronic control gear, Protection class II, IP 20 Ø = 170 mm, H = 43 mm\\" |
| 588 | \\"SITC OF Ceiling Mounted luminaire Tube with HPE (High-PerfoMance Efficiency) LED (Light Emitting Diode) system power: 10W, Luminous flux of luminaire 1000 lm, Colour temperature of 4000K, Neutral white, CRI>80, , SDCM<3 , R9>0 , THD<10% 230 V constant current driver, 70 % of luminous flux after 50,000 operating hours, Energy-efficient LEDs, Direct light emission, Luminaire profile in powde r coated White, snap-fit Satin diffuser for homogenous light distribution, ZHLS (ZERO HALOGEN LOW SMOKE) internal wiring, Electron ic control gear Protection class II, IP 20 L = 600 mm, B = 21 mm, H = 35 mm.\\" |
| 589 | \\"SITC OF Surface Mounted luminaire Zen 22 SM with LED (Light Emitting Diode), system power: 36 W, luminous flux of 3600 lm, colour t emperature of 4000 K, Neutral white, 230 V constant current driver, 70% of luminous flux after 50,000 operating hours, energy-effici ent LEDs, CRI > 80, , SDCM<3 , R9>0 , THD<10% direct light emission, Luminaire housing in CRCA, polyester white powder coat applied over a 5-stage pre-treatment, Opal diffuser for glare-free unifoM light, integral electronic control gear, Protection class I, IP40, L = 595 mm, B = 595 mm, H = 70mm \\" |
| 590 | \\"SITC OF Recessed downlight Blaire with LED (Light Emitting Diode), system power: 12 W, Luminous flux of luminaire 1320 lm, Colour t emperature of 4000 K, neutral white, CRI > 80, , SDCM<3 , R9>0 , THD<10% 230 V constant current driver, 70% of luminous flux after 5 0,000 operating hours; energy-efficient LEDs, direct light emission, housing in pre-cast die aluminium, Polyester powder-white colou red coat applied over a 5-stage pre-treatment trim, Prismatic diffuser for homogenous light distribution, Electronic control gear, Protection class II, IP 40, Ø = 136 mm, DA(Ø) = 125 mm, H = 56 mm\\" |
| 591 | Providing and fixing of lightning conductor finial, made of 25mm dia 300mm long, GI tube, having single prong at top, with 85mm dia 6 mm thick GI base plate including holes etc. complete as required. |
| 592 | Jointing copper / G.I. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut bolti ng/ sweating and soldering etc as required. |
| 593 | Providing and fixing GI tape 20mm x 3mm thick on parapet or surface of wall for lightning conductor as required. (for horizontal run ). |
| 594 | Providing and fixing G.I. tape 20mm x 3mm thick on parapet or surface of wall for lightning conductor as required. (For vertical run .) |
| 595 | Providing and fixing testing joint, made of 20mm x 3mm thick G.I. strip, 125mm long with 4 Nos. of G.I. bolts, nuts, check nuts and spring washers etc. complete as required. |
| 596 | Providing and laying G.I. tape, 32mm x 6mm thick, from earth electrode directly in ground as required. |
| 597 | Supplying, Installation, Testing & Commissioning of following capacity passenger Machine room less (MRL) lift with regenerative drive as per CPWD General Specification for Electrical Works (Part-III Lift & Escalator) 2003, BIS Codes, NBC 2016 as amended upto date having provision for barrier free access as per HaMonised Guidelines & Standards for Universal Accessibility in India - 2021 of MoHUA, serving different floors in the lift shaft as per detailed specifications enclosed and as under including all other equipment and accessories complete as required: \\"(i) Speed-1 MPS (ii) Floors-5 (G+4) (iii) Travel -17 Meters (approx.) (iv) Stops & opening- 5 stops and 5 openings (v) Controller: A.C. variable voltage & variable frequency (vi) Automatic rescue device (ARD) complete with dry maintenance free batteries as required. vii) Operation: Microprocessor based single automatic push button/simplex selective collective/duplex collective selective with/without attendant (viii) Power-415 Volts+10%, 3 phase, 50 Hz, 4 wires system (ix) Car Enclosure: Stainless steel scratch proof (Moon Rock/Honeycomb/ Hairline Finish) on all sides and stainless steel decorative ceiling with fans (indirect throw) and LED fitting. (x) The car flooring should be smooth and antiskid as approved by engineer-in-charge. (xi) Type of doors (a) Car: Power operated, centre opening horizontal sliding stainless steel scratch proof (Moon Rock/Honeycomb/ Hairline Finish). (b) Landing doors: stainless steel scratch proof . (xii) A hand rail not less that 600mm long at 900mm above floor level to be fixed adjacent to control panel in the lift car. (xiii)Voice announcement system in the car to announce the position of the elevator in the hoist way as the car passes or stops at floor served by the elevator.\\" \\"(xiv) Closed loop Control System, protection against power fluctuation, self diagnostic control, Landing doors 2 hours Fire rated, Overload detection and protection, Overspeed Governer, Dot Matrix LED D & P Indicators In Car & Landings, BMS Compatibility, tamper proof infrared curtain covering almost the entire height of the lift car door, AlaM horn, Anti Nuisance Operation, CCTV camera system with 4 MP IP camera, suitable NVR and HDD for 30 days storage backup , Firemen switch, 2/3 way intercom, Emergency Stop Switch with battery backup for fan and light fitting for 1 hour, pit ladder. (xv) The lift doors shall have a vision panel to enable persons with hearing impaiMent to signal for help or assistance in the event of an emergency. (xvi) An appropriate technological support be provided (Through emergency messaging |services or alaMs etc.) to respond to the emergency requirements of person with hearing impaiMent or deafness. (xvii) In case of failure of ARD or other electronic devices, a provision of manual rescue be provided\\" |
| 598 | 13 passenger (884kg) |
| 599 | Electrical-External Works |
| 600 | Main LT PanelIP: As per the LVSB Technical Specifications and Project Specific Attachments of the LVSB Switchboards |
| 601 | VTPN LIGHT & POWER DB-1 GROUND FLOOR Incomer 1 No. 100amps 4P MCCB(35KA) with overcurrent,earth fault and short circuit releases each complete with Outgoings 5 No. 40amps TP MCB 10KA 3 No. 32amps TP MCB 10KA VTPN LIGHT & POWER DB-1 GROUND FLOOR As Descrived Avobe |
| 602 | VTPN LIGHT & POWER DB-1 FIRST FLOOR Incomer 1 No. 100amps 4P MCCB(35KA) with overcurrent,earth fault and short circuit releases each complete with Outgoings 5 No. 40amps TP MCB 10KA 3 No. 32amps TP MCB 10KA VTPN LIGHT & POWER DB-1 FIRST FLOOR As Descrived Above |
| 603 | VTPN LIGHT & POWER DB (UPS) Incomer1 No. 63amps 4P MCCB(35KA) with overcurrent,earth fault and short circuit releases each complete with Outgoings 8 No. 32amps TP MCB 10KA VTPN LIGHT & POWER DB (UPS) As Described Above |
| 604 | Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required. |
| 605 | Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. |
| 606 | Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plat e having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. |
| 607 | Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ teMinatio n with GI thimble etc. as required. |
| 608 | Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe FRLSom earth electrode including connection with brass nut, bo lt, spring, washer excavation and re-filling etc. as required. |
| 609 | Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, s pring, washer excavation and re-filling etc. as required. |
| 610 | Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode incl uding connection with G.I. thimble excavation and re-filling as required. |
| 611 | Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required. |
| 612 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. |
| 613 | Upto 35 sq. mm |
| 614 | Above 35 sq. mm and upto 95 sq. mm |
| 615 | Above 95 sq. mm and upto 185 sq. mm |
| 616 | Above 185 sq. mm and upto 400 sq. mm |
| 617 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required. |
| 618 | Upto 35 sq. mm |
| 619 | Above 35 sq. mm and upto 95 sq. mm |
| 620 | Above 95 sq. mm and upto 185 sq. mm |
| 621 | Above 185 sq. mm and upto 400 sq. mm |
| 622 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing masonry ope n duct as required. |
| 623 | Upto 35 sq. mm |
| 624 | Above 35 sq. mm and upto 95 sq. mm |
| 625 | Above 95 sq. mm and upto 185 sq. mm |
| 626 | Above 185 sq. mm and upto 400 sq. mm |
| 627 | Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. |
| 628 | Upto 35 sq. mm (clamped with 1mm thick saddle) |
| 629 | Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp) |
| 630 | Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp) |
| 631 | Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp) |
| 632 | Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate with inscription there on, bolted /welded to 35 m m X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required. |
| 633 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. |
| 634 | 3.5 X 300 sq. mm (70mm) |
| 635 | 3.5 X 240 sq. mm (62mm) |
| 636 | 3.5 X 185 sq. mm (57mm) |
| 637 | 3.5 X 150 sq. mm (50mm) |
| 638 | 3.5 X 120 sq. mm (45mm) |
| 639 | 3.5 X 95 sq. mm (45mm) |
| 640 | 3.5 X 70 sq. mm (38mm) |
| 641 | 3.5 X 50 sq. mm (35mm) |
| 642 | 3.5 X 35 sq. mm (32mm) |
| 643 | 4 X 25 sq. mm (28mm) |
| 644 | 4 X 16 sq. mm (28mm) |
| 645 | 4 X 10 sq. mm (25mm) |
| 646 | 4 X 6 Sqmm |
| 647 | 3C X 10 sq. mm (22mm) |
| 648 | 3 X 6 Sqmm |
| 649 | 2 X 10 sq. mm (19mm) |
| 650 | Aluminium LT Cables FRLSH . 1.1 KV, XLPE insulated, extruded PVC type ST-2 inner sheathed, galvanized aMoured, PVC type ST-2 overall sheathed, Stranded, FRLSH, C2, Smoke density<40% |
| 651 | AL 3.5CX400 mm2 A2XFY |
| 652 | AL 3.5CX240 mm2 A2XFY |
| 653 | AL 3.5C x 185 mm2 |
| 654 | AL 3.5CX150 mm2 A2XFY |
| 655 | AL 3.5C x 120 mm2 |
| 656 | AL 3.5C x 95 mm2 |
| 657 | Al 3.5Cx70 mm2 |
| 658 | AL 3.5CX50 mm2 A2XFY |
| 659 | AL 3.5CX35mm2 A2XFY |
| 660 | AL 4CX25 mm2 A2XFY |
| 661 | AL 4CX16 mm2 A2XFY |
| 662 | AL 4CX10 mm2 A2XFY |
| 663 | AL 4CX6 mm2 A2XFY |
| 664 | AL 3CX10 mm2 A2XFY |
| 665 | CU 3CX6 mm2 2XWY |
| 666 | CU 2CX10 mm2 2XWY |
| 667 | Supply of Fire Survival Cable Aluminium LT Cables FRLSH. 1.1 KV, XLPE insulated, extruded PVC type ST-2 inner sheathed, galvanized aMoured, PVC type ST-2 overall sheathed, Stranded, FRLSH, C2, Smoke density<40% |
| 668 | Al,3.5Cx70 mm² |
| 669 | AL,3.5CX50 mm²,A2XFY |
| 670 | AL,3.5CX35mm²,A2XFY |
| 671 | AL,4CX25 mm²,A2XFY |
| 672 | AL,4CX16 mm²,A2XFY |
| 673 | AL,4CX10 mm²,A2XFY |
| 674 | Supply of following sizes XLPE insulated (Heavy duty) Aluminium or Copper conductor aMoured cables suitable for working voltage upto and including 1100 Volts complete as required and as per specifications. |
| 675 | 2 x 6 sq.mm |
| 676 | 4 x 6 sq.mm |
| 677 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. |
| 678 | Upto 35 sq. mm |
| 679 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required. |
| 680 | Upto 35 sq. mm |
| 681 | TeMination of the following sizes of XLPE insulated Aluminium/ Copper conductor cable including providing teMinal lugs,double comp ression gland , crimping the joints ,providing insulation tape,effecting teMinal connections to the equipment complete as required. |
| 682 | 2 x 6 sq,mm, Al conductor cable |
| 683 | Supply, laying and teMination of the following sizes of 650/1100 volts grade PVC insulated copper conducter wires in existing condui ts including end teMination with copper lugs. |
| 684 | 3 x 2.5 sq.mm. copper conductor, PVC insulated PVC sheathed wires. |
| 685 | Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surf ace conduit, or cutting the wall and making good the same in case of recessed conduit as required. |
| 686 | 25 mm dia |
| 687 | Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required. |
| 688 | 100mm dia |
| 689 | 250mm dia |
| 690 | Supply,fixing and laying of Heavy duty PVC pipes complete buried in floor with joints and other accessories as required. |
| 691 | 63 mm dia, 2mm thick |
| 692 | \\"Supply of Polar pole made of square mild steel pipe (grade YST 210) 100mm Square x 2.9mm thick with 5500mm Height. The split constructed double aM bracket made of MS pipe 100mm square x 2.9mm thick having 900mm aM length and 484mm height inclined at 10 degree. Single aM bracket contains build-in 60W LED module. 60W LED Module with expected service life of at least 60,000 operating hours. High Brightness, LED Light source do not pose any environment risks. Excellent theMal management heat sink. High efficiency polycarbonate optical lens. IP68 Ingress protection. IK09 impact protection. Colour rendering index(Ra) >70. Available colour temperature 3000K / 4000K / 5700K. Driver efficiency > 85%, power factor > 0.95, THD <10%, Surge Protection 6KV. Pole section welded by certified welders using high end MIG welding processes. PDC aluminium service door 330mm height x 75mm width shall be provided with the company logo embossed on the bottom of the door and safety rope with IP protection rating. The control gear tray is prewired with 2.5 Sq.mm cable, 6A SP MCB and 32A Ramanuj stud type 4 way teMinal block for loop-in / loop-out arrangement, 5A 2 Way teMinal connector and provision for earthing. Any other internal cables and connections shall not be covered in the scope of supply. Mild steel mounting plate 300mm Square x 16mm thick Steel of grade E250 to IS 2062 : 2011 with 4 elongated holes 48 x 24 to suit M20 x 500mm bolts of grade 4.6 at CC 215. This mounting steel plate along with foundation bolts of suitable size to be used for ensuring fiM grouting into the specially designed foundation. All dimension are within +/- 5% tolerance. After fabrication entire pole is shot blasted (Inhouse). The pole is coated with epoxy zinc phosphate primer and finished using environmentally stable powder coated (coating thickness 60-80 microns). The Pole shall be provided with Graphite grey / Anthracite grey / Black as standard colour options. Must have inhouse manufacuturing facilities along with powder coating shot blasting machines.KP-7229+KP-9108. Make: K- Lite/Ligman/Unilamp or equivalent\\" |
| 693 | Supply of Polar pole made of square mild steel pipe (grade YST 210) 100mm Square x 2.9mm thick with 5500mm Height. The split constructed double aM bracket made of MS pipe 100mm square x 2.9mm thick having 900mm aM length and 484mm height inclined at 10 degree. Double aM bracket contains build-in 2X60W LED module. 60W LED Module with expected service life of at least 60,000 operating hours. High Brightness, LED Light source do not pose any environment risks. Excellent theMal management heat sink. High efficiency polycarbonate optical lens. IP68 Ingress protection. IK09 impact protection. Colour rendering index(Ra) >70. Available colour temperature 3000K / 4000K / 5700K. Driver efficiency > 85%, power factor > 0.95, THD <10%, Surge Protection 6KV. Pole section welded by certified welders using high end MIG welding processes. PDC aluminium service door 330mm height x 75mm width shall be provided with the company logo embossed on the bottom of the door and safety rope with IP protection rating. The control gear tray is prewired with 2.5 Sq.mm cable, 6A SP MCB and 32A Ramanuj stud type 4 way teMinal block for loop-in / loop-out arrangement, 5A 2 Way teMinal connector and provision for earthing. Any other internal cables and connections shall not be covered in the scope of supply. Mild steel mounting plate 300mm Square x 16mm thick Steel of grade E250 to IS 2062 : 2011 with 4 elongated holes 48 x 24 to suit M20 x 500mm bolts of grade 4.6 at CC 215. This mounting steel plate along with foundation bolts of suitable size to be used for ensuring fiM grouting into the specially designed foundation. All dimension are within +/- 5% tolerance. After fabrication entire pole is shot blasted (Inhouse). The pole is coated with epoxy zinc phosphate primer and finished using environmentally stable powder coated (coating thickness 60-80 microns). The Pole shall be provided with Graphite grey / Anthracite grey / Black as standard colour options. Must have inhouse manufacuturing facilities along with powder coating shot blasting machines.KP-7229+KP-9108. Make: K- Lite/Ligman/Unilamp or equivalent |
| 694 | Supply of 45-50W Post top with LED 3000K, 4000K, 5700K 240Vac CRI >80 MacAdam step 3 Dimension not less than Ø400 x 807 mm, Light Distribution 360° Electronic driver ON/OFF, IP rating IP65/66, Spun aluminium top cover Ø400 mm of 1.6mm thickness, die cast aluminium decorative knob on top, Mild steel ( Sand Blasting with zinc primer supporting aM integrated with die-cast aluminium base suitable for mounting Ø76mm OD pipe. SS fasteners. Pure polyester powder coated process : Acid treatment & pure polyester powder coating. Clear acrylic diffuser with controlled downward light emission. Lamp fixed position. Lumen efficacy should be minimum 120lm/W. This luminaire should contains built-in LED modules. LED modules are engineered accordingly to the existing regulations of Lumen Maintenance (LM80) and Technical Memorandum (TM21), Lifespan of the luminaire L70B10>50,000 hours at 40°C. Operating ambient temperature range is from -15°C to +50°C. Driver efficiency >88%, power factor >0.96, THD <10%, Surge protection 6KV .the fixtures proposed must have passed LM 79 & LM- 80, latest Reports will be submitted post the issuance of LOA to the successful bidder and before the supply of material, Make of LEDs -LEDs of CREE / LUMINOUS / OSRAM / SEOUL / SAMSUNG/LUMILED /NICHIA/CITIZEN or equivalent CE & BIS Certified manufactrurer must have inhouse NABL certified labs. Make: K-Lite/Ligman/Unilamp or equivalent |
| 695 | Supply of Post top Lighting Pole of 4m-4.2m Height made out MS Pipe Ø76.1mm confiMing to YSt 210 and facilitating the luminaire mounting at the top. The pole shall be surfacemounted on a pre-foMed foundation. The base plate of the of the pole shall be E 250 grade MS 200 mm x 200mm, 12mm thick confiMing to IS2062:2011 shall be facilitated with elongated slots to suit the 300mm, J-type, M16 bolts, Grade 4.6 that shall be provided with suitable nuts and plain washers. The structurally sound pole emerging out of the base plate shall be architecturally designed with a decorative cast aluminium causeway base cover Ø330mm x 806mm(H), The grade of pressure diecast material shall be ADC12. A GDC embellishment is provided at appropriate height enhancing the decorative outlook of the pole. The grade of gravity die cast material shall be LM6. The Pole welding shall be done with certified welders using a V groove technique with a high end MIG welding process. A base compartment with a die cast aluminium door contoured to the poles's shape housing the gear tray, prewired with 2 way connector The surface preparation of the pole & components shall be done by shot blasting which is environmentally safe eliminating the chemical and acid use and ensuring the thoroughremoval of impuritise like, rust, oxides and other unwanted particles from the suface for high standard coating.The surface finish of the pole shall be Zinch rich primer coat & pure polyester powder coating or epoxy zinc phosphate primer followed by the environmentally stable Polyurethane based paint. Any other wiring/electrical consumables shall be under the scope of purchaser.Manufacuturer must have inhouse shot blasting and powder coating facilities. Make: K-Lite/Ligman/Unilamp or equivalent |
| 696 | Supply of Input power : 6W surface mounted compact spot light designed to provide directional light. Beam angle 15° / 25° / 40°. Luminaire made of pressure die cast aluminium alloy of high corrosion resistance and non corrosive A2 stainless steel fasteners. Clear toughened glass of 4mm thickness. Surface mounting spike made of polypropylene black. Hybrid optics with lens & mirror finish pure aluminium reflector combination for higher efficiency, lower optical losses with optimum glare suppression. Swivel range of 0° - 90°. Single cable entrance M10 cable gland. Protection class IP65/66. Mechanical resistance IK06. Pure polyester powder coated graphite grey / anthracite grey / jet black. Available colour temperature 3000K / 4000K / 5700K, Colour rendering index (CRI)>80. SDCM-3 MacAdam. K- Lite LED module with expected service life of at least 60,000 operating hours. Prewired with LED driver and suitable for operating on 240V, 50Hz single phase ac supply. Luminaire dimension : 101 x 64 x 93mmt. All tolerance should be ±15% , Make of LEDs -LEDs of CREE / LUMINOUS / OSRAM / SEOUL / SAMSUNG/LUMILED /NICHIA/CITIZEN or equivalent, CE & BIS Certified. Make: K-Lite/Ligman/Unilamp or equivalent |
| 697 | Supply of 12W Wooden finish bollard, Bollard luminaire designed for surface mounted. It must have Asymmetrical light distribution. Luminaire should be made of rectangular extruded aluminium tube (Grade6063), pressure die cast aluminium and non corrosive stainless steel fasteners. Clear acrylic diffuser. The Pressure die cast aluminium mounting plate should be of dimension 202mm x 52mm x 4mm thick with 2 elongated holes 20 x 14 to suit M12 bolts at CC130 with pure polyester powder coating. This mounting plate along with foundation bolts of suitable size to be used for ensuring fiM grouting into the specially designed foundation. Protection class IP65. Mechanical resistance IK10. Bamboo / teak / bronze gold finish. Colour temperature 4000K. Colour rendering index (CRI)>80. SDCM-3 MacAdam. K-Lite LED module with expected service life of at least 60,000 operating hours. Prewired with LED driver and suitable for operating on 240V, 50Hz single phase ac supply. Driver efficiency >80%, Power factor >0.9, THD <10%, Surge protection 3KV. Luminaire dimension : 200mm length x 110mm width x 1000mm height. CE & BIS Certified. Inhouse NABL accredited lab.. .Manufacturer must have inhouse NABL certified lab equipped with photo goniometer, IP, IK test facilities.Make of LEDs -LEDs of CREE / LUMINOUS / OSRAM / SEOUL / SAMSUNG/LUMILED /NICHIA/CITIZEN or equivalent, CE and BIS. Make: K-Lite/Ligman/Unilamp or equivalent |
| 698 | Supply of Input power : 6W and robust wall recessed luminaires for illuminating walls and stairs. Forward asymmetrical light distribution. Luminaire made of pressure die cast aluminium alloy of high corrosion resistance and non corrosive A2 stainless steel fasteners. ABS plastic installation housing for preparing the recess opening in wall / stairs. Clear acrylic diffuser. Single cable entrance via M10 cable gland. Protection class IP65. Mechanical resistance IK09. Pure polyester powder coated graphite grey / anthracite grey / jet black. Available colour temperature 3000K / 4000K / 5700K, Colour rendering index (CRI)>80. SDCM-3 MacAdam. K-Lite LED module with expected service life of at least 60,000 operating hours. Prewired with LED driver and suitable for operating on 240V, 50Hz single phase ac supply. Luminaire dimension : COD: 124 x 83 x 70mm. All tolerance should be ±15% Make of LEDs -LEDs of CREE / LUMINOUS / OSRAM / SEOUL / SAMSUNG/LUMILED /NICHIA/CITIZEN or equivalent, CE & BIS Certified. Make: K- Lite/Ligman/Unilamp or equivalent |
| 699 | Supply of 12W square decorative leser cut designer bollard LED 3000K, 4000K, 6500K 230-240Vac CRI >80 MacAdam step-3 Height 910mm Light Distribution Symmetrical, Electronic driver ON/OFF LUMINAIRE TYPE Bollard. IP rating IP66, Extruded square aluminium tube (grade 6063 with test certificate) Sq. 150 x 3mm thickness. Should have Bespoke laser cutting design options. SS fasteners. Must be equipped with Pre treated epdm black gaskets. Should have Die-cast aluminium mounting plate Sq.150 x 4mm thick with 3 elongated holes 20 x 12 to suit M10 bolts at PCD 90 with pure polyester powder coating. This mounting plate along with foundation bolts of suitable size to be used for ensuring fiM grouting into the specially designed foudation. Hot dip galvanised foundation bolt. Mechanical resistance IK06. It should be Pure polyester powder coated process : Acid treatment & pure polyester powder coating. Optical grade clear toughened glass diffuser of 4mm thickness with controlled downward light emission. Lamp fixed position.This luminaire should contains built-in IP 65 LED modules. LED modules are engineered accordingly to the existing regulations of Lumen Maintenance (LM80) and Technical Memorandum (TM21), Lifespan of the luminaire > 60,000 hours at 40°C. Operating ambient temperature range is from -15°C to +50°C. Driver efficiency >85%, power factor >0.9, THD <10%, Surge protection 2.5KV. Manufacturer must have inhouse NABL certified lab equipped with photo goniometer, IP, IK test facilities Make of LEDs -LEDs of CREE / LUMINOUS / OSRAM / SEOUL / SAMSUNG/LUMILED /NICHIA/CITIZEN or equivalent, CE and BIS. Make: K-Lite/Ligman/Unilamp or equivalent |
| 700 | Supply of Static White 3000K surface mounted compact spot light designed to provide directional light. Beam angle 15° / 25° / 40°. Luminaire made of pressure die cast aluminium alloy of high corrosion resistance and non corrosive A2 stainless steel fasteners. Clear toughened glass of 4mm thickness. Hybrid optics with lens & mirror finish pure aluminium reflector combination for higher efficiency, lower optical losses with optimum glare suppression.Power consumption should be between 18W to 20W at steady state full intensity luminaire should have minimum luminous flux of 1760 Lm. Color rendering index CRI # 80 and power factor of complete luminaire # 0.90, at white colour. Swivel range of 0° - 90°. Single cable entrance M10 cable gland. Protection class IP65/66. Mechanical resistance IK06. Pure polyester powder coated graphite grey / anthracite grey / jet black. Available colour temperature 3000K / 4000K, Colour rendering index (CRI)>80. SDCM-3 MacAdam. LED module with expected service life of at least 60,000 operating hours. Prewired with LED driver and suitable for operating on 240V, 50Hz single phase ac supply. Luminaire 160 x 100 x 494mm.Adequate heat sink with proper theMal management shall be provided. Operating Temperature : -10°C to +50°C, Operating Humidity : 10%-90%. THD should be less than 10%.Manufacturer must have inhouse shot blasting machine and NABL certified lab equipped with photo goniometer, IP, IK test facilities Make of LEDs -LEDs of CREE / LUMINOUS / OSRAM / SEOUL / SAMSUNG/LUMILED /NICHIA/CITIZEN or equivalent, the fixtures proposed must have passed LM 79 & LM-80, latest Reports will be submitted post the issuance of LOA to the successful bidder and before the supply of material CE & BIS Certified. Make Ligman, K-Lite, Unilamp or equivalent |
| 701 | Supply, laying, fixing Ladder and perforated type Cable Trays shall be manufactured as per IS /IEC 61537 and it shall be of Pre Galvanized bolted type and factory fabricated out of CRCA sheet with standard accessories like tees- Horizontal and Vertical, Circular bends- Horizontal and Vertical, Coupler plates, Reducers, 4-way cross, Tray covers, Fasteners. etc. for different loads and number and size of cables as given below. All indoor type cable trays shall be galvanized according to BS EN /IEC 10346 with 275 GSM and All outdoor type cable trays shall be Hot dip galvanized according to DIN EN ISO 1461 with 70 microns. |
| 702 | 750mm x 100mm x 3mm Runners 20 x 150 x 20 x 2.5 mm Rungs 20 x 30 x 20 x 2.5 mm 250 mm C/C |
| 703 | 600mm x 50mm x 3mm Runners 20 x 150 x 20 x 2.5 mm Rungs 20 x 30 x 20 x 2.5 mm 250 mm C/C |
| 704 | 600mm x 100mm x 3mm Runners 20 x 150 x 20 x 2.5 mm Rungs 20 x 30 x 20 x 2.5 mm 250 mm C/C |
| 705 | 450mm x 100mm x 3mm Runners 20 x 150 x 20 x 2.5 mm Rungs 20 x 30 x 20 x 2.5 mm 250 mm C/C |
| 706 | 300mm x 100mm x 3mm Runners 20 x 150 x 20 x 2.5 mm Rungs 20 x 30 x 20 x 2.5 mm 250 mm C/C |
| 707 | Providing & fixing 32mm x 32mm x 5mm GI angle suspenders & 40mm x 40mm x 5mm base supports for ladder cable trays of size 750mm & 60 0mm with all necessary fixing accessories. |
| 708 | Providing & fixing 25mm x 25mm x 5mm GI angle suspenders & 40mm x 40mm x 5mm base supports for ladder cable trays of size 450mm & be low with all necessary fixing accessories. |
| 709 | Perforated Cable Tray \\"Supplying and installaton following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with two numbers MS/GI Suspenders i/c base of suitable size MS/GI angle, bolts & nuts, painting suspenders, fastener etc as required.\\" |
| 710 | 100 mm width X 50 mm depth X 1.6 mm thickness |
| 711 | 150 mm width X 50 mm depth X 1.6 mm thickness |
| 712 | 300 mm width X 50 mm depth X 1.6 mm thickness |
| 713 | 450 mm width X 50 mm depth X 2.0 mm thickness |
| 714 | 600 mm width X 50 mm depth X 2.0 mm thickness |
| 715 | 750 mm width X 62.5 mm depth X 2.0 mm thickness |
| 716 | Supplying and installing following size of perforated perforated painted with powder coating M.S. cable trays bends with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspe nders etc.as required. |
| 717 | 100 mm width X 50 mm depth X 1.6mm thickness |
| 718 | 150 mm width X 50 mm depth X 1.6mm thickness |
| 719 | 300 mm width X 50 mm depth X 1.6mm thickness |
| 720 | 450 mm width X 50 mm depth X 2.0 mm thickness |
| 721 | 600 mm width X 50 mm depth X 2.0mm thickness |
| 722 | 750 mm width X 62.5 mm depth X 2.0 mm thickness |
| 723 | Supplying and installing following size of perforated perforated painted with powder coating M.S. cable trays Tee with perforation n ot more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspend ers etc.as required. |
| 724 | 100 mm width X 50 mm depth X 1.6mm thickness |
| 725 | 150 mm width X 50 mm depth X 1.6mm thickness |
| 726 | 300 mm width X 50 mm depth X 1.6mm thickness |
| 727 | 450 mm width X 50 mm depth X 2.0 mm thickness |
| 728 | 600 mm width X 50 mm depth X 2.0mm thickness |
| 729 | 750 mm width X 62.5 mm depth X 2.0 mm thickness |
| 730 | \\"Supplying and installing following size of perforated painted with powder coating M.S. cable trays Cross Member with perforation no t more than 17.5%, joined with connectors, suspended from the ceiling with two numbers MS/GI Suspenders i/c base of suitable size MS/GI angle, bolts & nuts, painting suspenders, fastener etc as required.\\" |
| 731 | 100 mm width X 50 mm depth X 1.6mm thickness |
| 732 | 150 mm width X 50 mm depth X 1.6mm thickness |
| 733 | 300 mm width X 50 mm depth X 1.6mm thickness |
| 734 | 450 mm width X 50 mm depth X 2.0 mm thickness |
| 735 | 600 mm width X 50 mm depth X 2.0mm thickness |
| 736 | 750 mm width X 62.5 mm depth X 2.0 mm thickness |
| 737 | Supplying and installing following size of perforated painted with powder coating M.S. cable trays Reducer with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with two numbers MS/GI Suspenders i/c base of suitable size MS/GI an gle, bolts & nuts, painting suspenders, fastener etc as required. |
| 738 | 100 mm width X 50 mm depth X 1.6mm thickness |
| 739 | 150 mm width X 50 mm depth X 1.6mm thickness |
| 740 | 300 mm width X 50 mm depth X 1.6mm thickness |
| 741 | 450 mm width X 50 mm depth X 2.0 mm thickness |
| 742 | 600 mm width X 50 mm depth X 2.0mm thickness |
| 743 | 750 mm width X 62.5 mm depth X 2.0 mm thickness |
| 744 | \\"Supplying Installation, Testing and Commissioning of on-grid Solar Photovoltaic Power Plant conforming to various applicable standards & strictly As per Tender Technical Specifications a) High Energy Efficiency Solar Photovoltaic Module of capacity 330 Wp or above, manufactured in India, conforming to IS 14286/IEC 61215, IS/IEC 61730- Part-1, IS/IEC 61730-Part-2. b)Power Conditioning Unit (PCU) of 350-800 V DC Input voltage range and 415 V AC, three phase, 4 wire, 50Hz +/- 2.5 Hz, output voltage suitable to generate AC with a variation of 10% at nominal voltage. Power with efficiency not less than 97%, total harmonic distortion less than 3% and suitable for ambient temperature from 0 to 50 0C, Minimum IP-65 for outdoor and Minimum IP 21 for indoor, Built-in meter and data logger, MPPT, switching devices IGBT/MOSFETs and controller Microprocessor /DSP. d) Real time online web interfaced Data Monitoring System complete with accessories for various parameters such as Solar Irradiance, temperature, AC Output Voltage and current, Output Power, Power factor, DC Input Voltage and Current, Time Active, Time disabled, Time Idle, Power produced and other parameters as per standard practices. e) Array junction box & Main junction box with IP 65 protection and termination arrangement for incoming and outgoing cable along with glands, lugs and other accessories etc. as required. Each junction box shall be made of GRP/FRP/Powder Coated Aluminium /cast .f) Lightning, surge voltage protection, earthing protection and grid islanding. g) Cables: Connections & Interconnections by required size IR/UV protected XLPE insulated copper conductor 1.1 kV grade armored power and control cables(ISI Marked) along with supplying & fixing of necessary channel/conduit, GI cable trays, supports,lugs, thimble and other accessories etc. as required. h) DC Distribution Board And AC Distribution Panel Board: IP65, free standing, metal cladded, having copper bus bar, having required protection and control gears, connection-interconnection, etc. as required.\\" |
| 745 | Online UPS- Input supply: Three Phase, Output supply: Three Phase Supplying, installation, Testing & Commissioning of following capacity at full load (Unity Power Factor) at operating temperature 0 to 40 0C, Relative humidity 0 to 95%, Online double conversion true sine wave Uninterrupted hot swapable (allow for the replacement or addition of battery modules without shutting down the entire system) modular Power Supply (UPS) system with N+1 modules (N denotes total number of modules required for rated capacity). The UPS shall include a Rectifier, inverter, battery bank suitable for 30 minutes back up (Battery VAH capacity shall not be less than 1600 VAH per KVA of UPS rating per Hour backup time) on full load (Battery shall be VRLA, SMF in ABS Container) and Static Bypass switch along with manual bypass, suitable isolation transformer for additional protection against neutral faults etc. UPS shall have inbuilt phase sequence correction. The UPS systems offered are to be of the latest technology with Digital Control Microprocessor based for reliable operation using Insulated Gate Bipolar Transistor (IGBT)'s both for the rectifier & inverter (3 Level) with PWM (Pulse Width Modulation). The quality of design, manufacturing and inspection process should confirm to the relevant Inter-national standards such as IEC/EN/VDE. The operating efficiency of the UPS systems shall be >96% while operating on battery mode and delivering quality power to the 100% non-linear loads. Current total harmonic effect(ITHD) on the input grid shall be < 5% at 50 %load. (The required LC ( inductor (L) and a capacitor (C)) filters shall be included in UPS cost), extreme power factor kit to be included to limit the input power factor (PF) to 0.99 and output power factor shall be unity (i.e. kw rating of the UPS shall be kva rating x 1 ), however UPS shall be suitable to take load at 0.7 laging to 0.7 leading power factor loads. UPS shall be suitable for- incoming supply AC : 3Phase 400V +/-20%, 50 Hz +/-5 Hz AC Output voltage: 3Phase 415 Volt, 50 Hz +/- 0.2Hz Overload capacity of 120% for 10 mins Sine wave output. Non condensing Noise level less than 60db at 1 meter distance Protections: Input Under voltage,over voltage, abnormal out voltage, battery over charging, output over current, short circuit protection, battery deep discharge protection, 10KV surge. UPS must comply with low voltage electromagnetic compatibility (EMC) achieved as per EN 6204, EN6204 Part I and Part 2, it shall be a Voltage and Frequency Independent (VFI)-type UPS. Communication RS232/RS485/SNMP port open protocol for BMS integration, all hardware & software for iOT Communication as per approved by Engineering in charge. Required battery racks and interconnecting copper conductor cables of suitable size and connectors and all required accessories are inclusive of the cost). This system must provide a means for logging and alarming of all monitored points plus email notification. Forced air-cooling with integral inbuilt fans with redundancy (if one fan fail UPS should be able to handle at least 80% of the load, Noise Level 65 DB at 1 meter distance. The system shall be in compliance IEC 62040- 1,2 & 3,IS: 16242 and CPWD Specification. Display Panel (minimum) (In build 5 inch or more LC Display / LED) to display : a) Input: Voltage, current, Frequency. b) Bypass: Voltage, Frequency. c) Output: Voltage, frequency, Current. d) Battery:Voltage, Capacity. e) Load: KVA, KW, Percentage. f) Temperature: STS, Inverter, PFC. g) Event Logging & Statistical Data (On LCD/LED): UPS should capture and display up to 3000 events like:Over temperature / DC Bus Fail / Fan Fail / Fuse Fail / Overload / Short-circuit / Device Fail / Inverter Fail / Rectifier Fail / Bypass Fail, etc. h) Statistical Data: No. of power failures / Transfers to Bypass / Total Running time, etc. i) Mains Mode of Operation /Battery Mode of Operation / Bypass feeding the load / UPS Fault /Battery charging and discharging, overload, battery voltage and battery capacity. j) Audible Alarms : Mains Failure, Battery Low Alarm, UPS Overload, Fault, Shutdown, Input Over, Under Voltage, Output Over, Under Voltage, Battery Over, Under Voltage, Over Load and short circuit, Over Temperature. The UPS should have QR code which should contain drawing, test report OEM manual, Geo- Tag of manufacturing location etc. 20KVA (Each Power module shall be < 10 KVA) |
| 746 | Electrical-HVAC |
| 747 | Variable Refrigerant Volume / Flow Air-conditioning System (Heating & Cooling both) \\"Supply, Installation, Testing & Commissioning of Modular type Variable Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling/heating having 100% heMetically sealed inverter type twin Rotary/Scroll Compressor(s) ,minimum two compressors (with individual separate PCB) for above 14HP modules, microprocessor based Controller, top discharge type condensing unit(s), with R-410-A Refrigerant or equivalent, vibration Isolators with suitable foundation etc. complete as required. To have better e#ciency condenser fan shall be capable to operate at different speed with respect to load. The unit shall deliver the rated capacity and in confiMation as per IS 18728:2024 and CPWD Specifications and work even at 50°C ambient temperature without tripping. The system shall be able to deliver 100% of the rated capacity upto 39 Degree Celcius.The unit shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply and BMS compatible. The unit shall be filled with first charge of the refrigerant and ready for use as required. The condenser should be coated with a hydrophilic film to prevent water accumulation on the surface of the heat exchanger, enhance water dispersion, and reduce the risk of degradation, thereby improving overall perfoMance and durability. The Indian Seasonal Energy E#ciency Ratio (ISEER) of the unit shall be as per Energy Conservation and Sustainable Building Code (ECSBC) 2024 as below and complete as per CPWD specification, connections, inter connections etc. as required. (For capacity <40 kWr ISEER 6.4, Capacity > 40 and <70 ISEER 6.5, Capacity > 70 ISEER 6.6 for ECSBC+ Building) For Cooling or Heating or Both\\" |
| 748 | 6 HP to 8 HP (6 HP) |
| 749 | 10 HP to 12 HP (10 HP) |
| 750 | 10 HP to 12 HP (12 HP) |
| 751 | 14 HP to 22 HP (14 HP) |
| 752 | 14 HP to 22 HP (16 HP) |
| 753 | 14 HP to 22 HP (18 HP) |
| 754 | VRV/VRF 4- Way Cassette Type Units Supply, Installation, Testing and Commissioning of following minimum capacity 4 way Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan / dynamically balanced blower, multispeed motor, coil section with DX Copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration Isolation, Corded remote control etc., suitable for operation on single phase 230 V ± 10%, 50Hz AC supply, complete, as required. The Indoor units must shut down upon receiving a singal from the BMS System/Fire Signals. The system shall be capable to adjust air flow as per room requirement in auto mode. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. (Make will be same as of Outdoor) |
| 755 | 0.8 ton |
| 756 | 1 ton |
| 757 | 1.2 ton |
| 758 | 1.6 ton |
| 759 | 3.6 ton |
| 760 | VRV/VRF Ceiling Mounted Ductable \\"Supply, Installation, Testing and Commissioning of following minimum capacity and external static pressure VRF/VRV ceiling mounted mid high static ductable type Indoor unit equipped with washable synthetic media pre- filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, corded remote control, outer cabinet, vibration Isolators, drain pan, drain pump, other necessary supports etc., suitable for operation on single phase AC supply 230 V ± 10%, 50 Hz complete as required. The Indoor units must shut down upon receiving a singal from the BMS System/Fire Signals. The system shall be capable to adjust air flow as per room requirement automatically. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. (Make will be same as of Outdoor) High Static Ductable Units (Minimum 49 to 77 Pascal External Static Pressure)\\" |
| 761 | 3.2 TR Ductable Unit |
| 762 | 4.0 TR Ductable Unit |
| 763 | 4.6 TR Ductable Unit |
| 764 | \\"Supply, Installation, Testing and Commissioning of following minimum capacity and external static pressure VRF/VRV ceiling mounted high ductable type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, corded remote control, outer cabinet, vibration Isolators, drain pan, drain pump, other necessary supports etc., suitable for operation on single phase AC supply 230 V ± 10%, 50 Hz complete as required. The Indoor units must shut down upon receiving a singal from the BMS System/Fire Signals. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. (Make will be same as of Outdoor)\\" |
| 765 | 5.5 TR Ductable Unit |
| 766 | VRV/VRF Central Controller for Indoor & Outdoor Units |
| 767 | \\"Supply, installation, testing & commissioning of Central Controller capable of controlling of all IDUs, ODUs complete with necessa ry hardware, accessories etc. to perfoM the following functions: (a) Control of IDUs, ODUs Units as above with monitoring of vital paraMTs such as temperature sensing & setting, ON/OFF, status etc. (b) PeMit / prohibit function of EACH remote controlled unit (c) Operation of units in individually or in group (d) Fault indication with AlaM (e) Provide interface to connect complete VRF system with third party BMS system (f) The central controller will be complete including all hardware & software suitable to perfoM above function.Complete in all resp ect as required at site.\\" |
| 768 | Supplying, installing, testing and commissioning of factory built ceiling mounted double skin type treated fresh air unit with outdo or air processing unit as per OEM |
| 769 | 635 CFM capacity 4.0 TR |
| 770 | 988 CFM capacity 6.4 TR |
| 771 | 1236 CFM capacity 8.0 TR |
| 772 | Supplying, installing, testing and commissioning of direct driven PROPELLER FANS. EACH fan shall be complete with peManent split capacitor or shaded pole motor, mounting plate with light weight type plastic impellers with aerofoil contours for high efficiency & low noise & gravity louvers for weather protection as required. Fan selection arrangement and Electrical characteristics shall be as follows : |
| 773 | 200 CFM Total Static Pressure OF 15 MM WG |
| 774 | 1300 CFM Total Static Pressure OF 15 MM WG |
| 775 | Supplying, installing, testing & commissioning of INLINE FANSsuitable for installing in any position in vertical or horizontal ducts . The casing shall be double skin, internally acoustically lined and constructed of galvanised stee 18 SWG. The inline fan shall be with backward/forward curve centrifugal impeller fitted with maintenance free external rotor motor, flexible connections at the disc harge & inlet. high efficiency (efficiency-1 / IE-2) TEFC squirrel cage 3 phase 50 Hz, 415 Volt, Class H insulated with IP 54 protec tion fan motor, V- belt Drive package consisting of Motor Pulley, fan Pully, V- elt, belt Guard and other accessories. quoted price shall be inclusive of DOL starter panel with cabling between starter panel and fan. |
| 776 | 400 CFM,Total static pressure of 25 mm WG |
| 777 | \\"Supply, Installation and commissioning of Non recirculating centrifugal Air Curtains with following specifications:- Artistically designed curvaceous body constructed in aluminium extruded powder coated sections with powder coated sheet metal base and mounting plates. Motors constructed in aluminium body to enable rapid cooling, with copper winding, bearing based motors made in CRNO core to run continuously for 24X7 operation, with theMal overload protection. Dynamically balanced centrifugal Blowers made in virgin plastic, with aerodynamically designed fins to deliver high volume of air., the suction grills should be made in plastic. Air Curtain should have dual speed with max. Velocity at Nozzle between 19-21 m/s. Air curtain should be coupled with the door, with a automatic magnetic limit switch, to synchronise working of air curtain with opening of the door. Make:Mitzvah, Olefini, Euronics or equivalent. Complete in all respect as required at site.\\" |
| 778 | Air Curtain Door 2000W x 2100H |
| 779 | Air Curtain Door 1000W x 2100H |
| 780 | Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system,complete with fittings, with suitable ad justable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of 19 mm thick insulation as given below for Suction and Liquid lines, all accessories as per specifications etc. as required : |
| 781 | 6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation |
| 782 | 9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation |
| 783 | 12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation |
| 784 | 15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation |
| 785 | 19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation |
| 786 | 22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation |
| 787 | 28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation |
| 788 | 34.9 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation |
| 789 | 41.27 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation |
| 790 | 400 mm Wide G.I Tray Covered with G.I Sheet for Copper Tubes. |
| 791 | Supply & fixing Of MS stand for outdoor units |
| 792 | Supply & fixing Of Branch Kit Joints. |
| 793 | Supplying and installation of Refnet Joints as per site conditions. |
| 794 | ALL Control/communication wiring between indoor and outdoor units with FRLS PVC conduit and necessary clamps/saddling etc. complete as Required. |
| 795 | Supplying, laying, fixing and installation of rigid PVC drain piping of 6 kg/sqcm, duly insulated with 6/9 mm thick nitrile rubber p ipe section, complte with all necessary fitting such as elbow, tees, reducers, serviceable \\"P\\" traps etc. and supports such as clamp s etc. complete as per specifications. |
| 796 | 25 mm dia |
| 797 | 32 mm dia |
| 798 | 40 mm dia |
| 799 | 50 mm dia |
| 800 | Supply, installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular/round ducting Complete with ne oprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of follow ing sheet thickness complete as per specifications. |
| 801 | Thickness 0.63 mm sheet (24 Gauge) |
| 802 | Thickness 0.80 mm sheet (22 Gauge) |
| 803 | Thickness 1.00 mm sheet (20 Gauge) |
| 804 | Thickness 1.25 mm sheet (18 Gauge) |
| 805 | Note- Cost shall include hanging and support of GSS ducts and AHUs shall be with Gripple/Hilti Hangers & Supports complete with end fixing in accordance with the approved shop drawings and as required by the specifications. |
| 806 | Supply, installation, testing and commissioning of GI volume control duct damper complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc., as per specifications. |
| 807 | Supplying & fixing of powder coated extruded aluminium Supply Air Grills with aluminium volume control dampers as per specifications . |
| 808 | Supplying & fixing of powder coated extruded aluminium Return Air Grills with louvers but without volume control dampers complete as specification. |
| 809 | Supplying, fixing testing commissioning of supply air diffusers round/square flat plate type smuge proof of powder coated aluminium with aluminium volume control dampers with anti smudge ring & removable core. Make: Airflow(mapro), Ruskin titus, Systemair or equivalent. |
| 810 | Supplying, fixing testing commissioning of Return air diffusers round/square flat plate type smuge proof of powder coated aluminium without volume control dampers with anti smudge ring & removable core.Make: Airflow(mapro), Ruskin titus, Systemair or equivalent. |
| 811 | Supplying, Fixing,testing and commissioning of fire dampers in supply air duct/main branch and return air path as and where required of required sizes i/c control wiring,the damper shall be motorized and spring return so as to close the damper in the event of powe r failure automatically and open the same in case of power being restored. The spring return action shall be inbuilt mechanism and n ot externally mounted. The damper shall also be closed in the event of fire signal complete as per specification. |
| 812 | Fire damper |
| 813 | Actuator |
| 814 | Supply, installation testing and commissioning of 10 mm thick duct acoustic insulation Inside the Duct with open cell nitrile rubbe r to be applied using manufacturer's recommended Rubber based Adhesive in a blend of solvents. complete as required and as per speci fications. Complete as required as per site conditions. |
| 815 | Underdeck insulation for exposed slab with 50 mm thick \\"TF\\" Quality Expanded polystyrene with washers, G.I Crossed binding wires, jo ints sealed with bitumen etc. complete as per specification |
| 816 | Supply, installation and testing & Commissioning of flexible (Canvas) connection between duct and machine |
| 817 | Louvers |
| 818 | Supplying, installing, testing and commissioning of Fresh Air powder coated Anodized extruded aluminium construction fresh air lou vers (50 mm deep) (Fresh air louver with VCD , bird screen & rattle-free) complete as per specification. |
| 819 | Supplying, installing, testing and commissioning of Exhaust Air powder coated Anodized extruded aluminium construction fresh air lou vers (50 mm deep) air louver without VCD , bird screen & rattle-free)complete as per specification. |
| 820 | Supply and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (class \\"O\\") insulatio n on existing duct after applying two coats of cold setting adhesive (CRS X compound). The joints shall sealed with 50 mm wide and 3 mm thick self adhesive Nitrile rubber tape insulation complete as per specification |
| 821 | 19 mm |
| 822 | HVAC ELECTRICAL |
| 823 | \\"Design, fabrication, assembly, wiring and supply of front operated dead front cubicle type compartmentalised as per Form 3B, rear access free standing, dust and vermin proof ,suitable for outdoor application, main switchboards suitable for use at 415 volts, 3 phase 4 wire 50 Hertz system suitable for a symmetrical fault level of 35 kA at 415 volts, fabricated from 2 mm thick CRCA MS sheets with hinged, gasketted (metal based neoprene) and lockable doors having structural reinforcement with suitable angle/channel/T/flat sections including 3 mm thick gland plates on top and bottom and including lifting hooks and including GI earth strip of required size with 2 nos earthing terminals and including powder coated paint finish of approved shade over metal surface cleaned and treated with seven tank process complete with interconnections etc as per specifications, as required and as below.Complete as required as per site conditions. EACH Motor control Centre(MCC)/Panel shall include cost of cabling, wiring, control wiring & inter locking in order to execute the required sequence of operation.A separate EACH of CTs to be provided for wiring from CT’s and voltage transducers to be brought on to separate EACH of terminals.Note : ACB shall be motor duty and suitable for 35 KA (ICS) fault currentMotor Control Centre (415 V) consisting ofIncoming1 No. 250 amps 4 Pole ACB ICU=ICS=35KA having front operating handle with door interlock and as per preamble above complete with the following :1 NO. digital VOLTRMT with selector switch - 1 EACH1 NO digital AMERMTOver voltage tripping mechanism for persistent voltage exceeding 110% of the rated voltage for more than 5 minutes - 1 EACHPhase indicating lamps, with toggle switches.Terminals to receive XLPE insulated Aluminium cablesBusbarTPN bus bars shall be of aluminium and shall be sleeved. Phase bus bars shall be rated at 300 amps and neutral bus bar shall be of 50% capacity suitable to withstand symmetrical fault level of 25KA of 415 V.Maximum density of aluminium bus bars for current carrying capacity shall be one amp per square mm.Outgoing5 No. EACH 25 amps MCCB outgoing feeders to 6.0HP-12HP VRV outdoor unit .EACH of these compartment shall contain CT operated digital amRMT of 0-25 amps range with selector switch, and an indicating lamp with MCB and toggle switch for ‘ON’ status.(1 spare but without RMTing )5 No. EACH 40 amps MCCB outgoing feeders to 16 HP-18 HP VRV outdoor unit .EACH of these compartment shall contain CT operated digital amRMT of 0-60 amps range with selector switch, and an indicating lamp with MCB and toggle switch for ‘ON’ status.(1 spare but without RMTing )Supplying,Receiving, fixing, testing & commissioning of HVAC Panel for VRV-2 as described above.Complete as required as per site conditions.\\" |
| 824 | Design, fabrication, assembly, wiring and supply of front operated dead front cubicle type compartmentalised as per Form 3B, rear access free standing, dust and vermin proof ,suitable for outdoor application, main switchboards suitable for use at 415 volts, 3 phase 4 wire 50 Hertz system suitable for a symmetrical fault level of 35 kA at 415 volts, fabricated from 2 mm thick CRCA MS sheets with hinged, gasketted (metal based neoprene) and lockable doors having structural reinforcement with suitable angle/channel/T/flat sections including 3 mm thick gland plates on top and bottom and including lifting hooks and including GI earth strip of required size with 2 nos earthing terminals and including powder coated paint finish of approved shade over metal surface cleaned and treated with seven tank process complete with interconnections etc as per specifications, as required and as below.Complete as required as per site conditions.EACH Motor control Centre(MCC)/Panel shall include cost of cabling, wiring, control wiring & inter locking in order to execute the required sequence of operation.A separate EACH of CTs to be provided for wiring from CT’s and voltage transducers to be brought on to separate EACH of terminals.Note : ACB shall be motor duty and suitable for 35 KA (ICS) fault currentMotor Control Centre (415 V) consisting ofIncoming1 No. 250 amps 4 Pole ACB ICU=ICS=35KA having front operating handle with door interlock and as per preamble above complete with the following :1 NO. digital VOLTRMT with selector switch - 1 EACH1 NO digital AMERMTOver voltage tripping mechanism for persistent voltage exceeding 110% of the rated voltage for more than 5 minutes - 1 EACHPhase indicating lamps, with toggle switches.Terminals to receive XLPE insulated Aluminium cablesBusbarTPN bus bars shall be of aluminium and shall be sleeved. Phase bus bars shall be rated at 300 amps and neutral bus bar shall be of 50% capacity suitable to withstand symmetrical fault level of 25KA of 415 V.Maximum density of aluminium bus bars for current carrying capacity shall be one amp per square mm.Outgoing5 No. EACH 25 amps MCCB outgoing feeders to 6.0HP-12HP VRV outdoor unit .EACH of these compartment shall contain CT operated digital amRMT of 0-25 amps range with selector switch, and an indicating lamp with MCB and toggle switch for ‘ON’ status.(1 spare but without RMTing )5 No. EACH 40 amps MCCB outgoing feeders to 16 HP-18 HP VRV outdoor unit .EACH of these compartment shall contain CT operated digital amRMT of 0-60 amps range with selector switch, and an indicating lamp with MCB and toggle switch for ‘ON’ status.(1 spare but without RMTing )Supplying,Receiving, fixing, testing & commissioning of HVAC Panel for VRV-2 as described above.Complete as required as per site conditions. |
| 825 | Supplying & erecting approved make RCBO (Electro magnetic type only) working on residual current device having 10 KA short circuit b reaking capacity and 300 mAmp.tripping time confoMing to IS 12640 test knob facility trip free mechanism operating for rated leakage at nominal ten volt, complete erected including all materials lugs screws etc. completed. |
| 826 | 6A to 25 A, 4 Pole Three Phase Cat. II |
| 827 | 32A to 40 A, 4 Pole Three Phase Cat. II |
| 828 | 63A, 4 pole Three Phase Cat. II |
| 829 | Supplying & fixing box for housing RCBO combination made of 18 SWG sheet steel duly powder coated with gasket, dust & veMin proof,wa ter proof, bakelite shield two earthing teMinals for following type of RCCB, RCBO |
| 830 | For 4 Pole |
| 831 | Providing and erecting PVC Innersheathed, UnaMoured/AMoured (Aluminium wire for single core up to 70 sq. mm & balance Aluminium stri p, Galvanised wire for cables upto 2Cx10 sq. mm, 3Cx10 sq. mm, 4Cx6 sq. mm & balance all galvanised steel strip) Extruded PVC Type S T2 Outer Sheathed, 650 V/1100 V Grade as per IS 7098 (Part 1) 1988 with upto Date Amendments. |
| 832 | 3 core 4 Sq. mm |
| 833 | 3 core 6 Sq. mm |
| 834 | 3 core 10 Sq. mm |
| 835 | 3 core 16 Sq. mm |
| 836 | 3 core 25 Sq. mm |
| 837 | Providing and erecting Copper Power Cables, Solid Copper Conductor upto 6 sq. mm & Balance Stranded Copper, XLPE Insulated, Cores La id Up, PVC Innersheathed, UnaMoured/AMoured (Glavanised wire for cables up to 10Cx1.5 sq. mm, 8Cx2.5 sq. mm, 2Cx10 sq. mm, 3Cx10 sq. mm, 4Cx6 sq. mm & balance all galvanised steel strip), Extruded PVC Type ST2 Outer Sheathed, 650 V/1100 V Grade as per IS 7098 (Par t 1) 1988 with upto Date Amendments. |
| 838 | 4 core 2.5 Sq. mm |
| 839 | 4 core 4 Sq. mm |
| 840 | 4 core 6 Sq. mm |
| 841 | Providing and erecting XLPE(IS:7098)(I)-88 ISI aMoured cable multistrand Copper conductor for 1.1 KV. to be laid on wall with n ecessary clamps or in existing trench / pipe at road crossing or floor of following size of cables. |
| 842 | 4 core 10 Sq. mm |
| 843 | 4 core 16 Sq. mm |
| 844 | 4 core 25 Sq. mm |
| 845 | \\"Supplying and erecting approved make GRP / FRP Ladder type Cable Tray Material – Corrosion Resistant Polyester Flame Retardant U.V. Stabilized Resin System - Manufactured from Pultruded Sections - Polyester Resin System, Glass Content : 55 – 60 % - Thickness- Rung Sq. Hollow Tube 25mm x 25mm - Fixing of Rung to Side Rail with TheMoplastic Pin & Epoxy Adhesive, Assembly Single Stroke 3 MT Length- Rung Spacing – 300mm - Length of Tray: 3000mm- Support Span – 2500mm, Deflection L/200 or < 10mm whichever is less - Specification Followed NEMA FG1 1993- UV Resistant - Flame Retardant – IS 6746 - Appendix K/UL 94, Very Low Flammability - Oxygen Index – Minimum 30% as per ASTM D 2863 Flame Spread (Extent of Burning) – 20mm as per Standard ASTM D 635 - Tensile Strength – 4000 – 8000 Kg/Cm2 as per Standard\\" ASTM D 638 - Flexural Strength – 2500 – 10000 Kg/Cm2 as per Standard ASTM D 790- Izod Impact Strength – 130 Kg/Cm2 as per Standard ASTM D 256- Compressive Strength – 2500 – 5000 Kg/Cm2 as per Standard ASTM D 695- Barcol Hardness – 50 – 65 |
| 846 | (A) Width 150 mm, Side Member “C” Section : 75 x 25 x 25mm with 4mm Thickness, Loading 30Kg./MT With Concentrated Load 70Kg. at cent er of the span |
| 847 | (B) Width 300 mm, Side Member “C” Section : 100 x 35 x 35mm with 4mm Thickness, Loading 60Kg./MT With Concentrated Load 70Kg. at cen ter of the span |
| 848 | Fire Alarm System |
| 849 | Supplying, installation, testing and commissioning of micro processor based intelligent addressable main fire alarm panel, central p rocessing unit with the following loop modules and capable of supporting not less than 240 devices (including detectors) and minimum 120 detectors per loop and loop length up to 2 km, network communication card, minimum 320 character graphics/ LCD display with tou ch screen or other keypad and minimum 4000 events history log in the non volatile memory (EPROM), power supply unit (230 ± 5% V, 50 hz), 48 hrs back-up with 24 volt sealed maintenance free batteries with automatic charger. The panel shall have facility to connect printer to printout log and facility to have seamless integration with analog/digital voice evacuation system (which is part of the schedule of work under SH: PA System) and shall be complete with all accessories . The panel shall be compatible for IBMS system wit h open protocol BACnet/ Modbus over IP complete as per specifications |
| 850 | Two Loop Panel. |
| 851 | Supplying, installation, testing & commissioning of central graphical fire alarm management system to centrally monitor and operate the fire alarm system complete as required. |
| 852 | Supplying, installation, testing & commissioning of smoke detector with builtin LED complete with all connections ect. As required |
| 853 | Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover com plete with all connections etc as required. |
| 854 | Supplying, installation, testing & commissioning of fault isolator complete with base as required. |
| 855 | Supplying, installation, testing & commissioning of addressable fire control module complete as required. |
| 856 | Supplying, installation, testing & commissioning of addressable phone control module complete as required. |
| 857 | Supplying, installation, testing & commissioning of addressable manual call point complete as required. |
| 858 | Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required. |
| 859 | Supplying, installation, testing & commissioning of fire fighter telephone handset complete as required. |
| 860 | Supplying, installation, testing & commissioning of fire fighter phone jack complete as required. |
| 861 | Supplying & laying of 2x1.5 sqmm fire survival armoured cable, 600/1000V rated with annealed copper conductor having glass mica fire barrier tape covered by an extruded layer of Cross Linkable Ethylene Propylene Rubber (EPR) insulation and LSZH inner bedding, stee l wire armouring & LSZH outer sheath complete as required. |
| 862 | Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, s teel wire armouring & FRLS outer sheath complete as required. |
| 863 | Supplying and fixing 25 mm dia MS flexible pipe with PVC coating along with all ancillaries and accessories like coupler etc. as req uired. |
| 864 | Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB, MP3 player (including 6 zone button pag ing station) with seamless integration facility with main fire alarm panel for voice evacuation complete as required. |
| 865 | Supplying, installation, testing & commissioning of 1.5/3/6W ceiling speaker complete as required. |
| 866 | Supplying, installation, testing & commissioning of 1.5/3/6W metal box ceiling/wall speakers complete as required. |
| 867 | Supplying, installation, testing & commissioning of digital audio amplifier 500 Watt, 25V rms operating at 240 volt AC supply comple te as required. |
| 868 | directional sound speaker with voice and integral audio amplifier with selectable sound pulse patterns complete as required. |
| 869 | Supplying, installation, testing & commissioning of Voice command keypad 6 zone, with microphone assembly complete as required. |
| 870 | Supplying & laying of 2x1.5 sqmm fire survival armoured cable, 600/1000V rated with annealed copper conductor having glass mica fire barrier tape covered by an extruded layer of Cross Linkable Ethylene Propylene Rubber (EPR) insulation and LSZH inner bedding, stee l wire armouring & LSZH outer sheath complete as required. |
| 871 | Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, s teel wire armouring & FRLS outer sheath complete as required. |
| 872 | Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required. |
| 873 | speaker cable Single pair, 2-core, 1.5 sqmm |
| 874 | speaker cable Two pair, 2-core, 1.5 sqmm |
| 875 | speaker cable Three pair, 2-core, 1.5 sqmm |
| 876 | speaker cable Four pair, 2-core, 1.5 sqmm |
| 877 | Supplying and fixing 25 mm dia MS flexible pipe with PVC coating along with all ancillaries and accessories like coupler etc. as req uired. |
| 878 | Fire Fighting System |
| 879 | Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 1239/Class -II of IS: 3589 including Wel ding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable cl amp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : |
| 880 | 100 mm dia |
| 881 | \\"Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with ca st iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required : \\" |
| 882 | Single Headed Gunmetal Material |
| 883 | Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : |
| 884 | 100 mm dia |
| 885 | Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted bet ween flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete a s required. |
| 886 | Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubbe r gasket, GI bolts, nuts, washers etc.as required : |
| 887 | 100 mm dia |
| 888 | Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc . conforming to IS 636 (type-A) as required : |
| 889 | Gunmetal Material |
| 890 | \\"Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. (a) 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 (b) 20 mm nominal internal dia gun metal globe valve & nozzle. (c) Drum and brackets for fixing the equipmets on wall. (d) Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.\\" |
| 891 | 40 Metre Length |
| 892 | Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suita ble for instantaneous connection to interconnect hose pipe coupling as required: |
| 893 | Gunmetal Material |
| 894 | Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with ca p and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required: |
| 895 | \\"Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flange d connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and painting with synthetic enamel paint of approved shade as required. \\" |
| 896 | Providing and fixing of Fire Hose Cabinet size not less than 2.1 x 1.2 x 0.90 mtr made out of M.S. sheet not less than 1.5 mm thick having central opening and 4 mm thick glazed glass doors (Two nos.) suitably marked on the outside 'with the letters \\"FIRE HOSE \\" including necessary locking arrangement and painting in PO red colour suitable to accommodate, internal hydrant valve, 2 nos 15 mtr long Hose pipe, branch pipe, nozzle and fire man's axe. It shall be fixed inside the FHC Cabinet Complete as required . |
| 897 | Providing and fixing standard firemans axe with heavy rubber handle. |
| 898 | Providing and fixing dial type pressure gauge with isolation cock and copper pipe on main header Dial diameter 100 mm celebratio n 0-16 / sq. cm. |
| 899 | Providing and fixing Fire Extinguishers (CO2 type powder ) 4.5 Kg Capacity complete with all accessories as per manufactu rers specifications. |
| 900 | Providing and fixing Fire Extinguishers (A, B, C type powder ) 6 Kg Capacity complete with all accessories as per manufact urers specifications. |
| 901 | Providing and fixing Fire Extinguishers (A, B, C type powder ) 9 Kg Capacity complete with all accessories as per manufact urers specifications. |
| 902 | Providing and fixing Fe 36 modular Fire Extinguishers 10 Kg Capacity complete with all accessories as per manufacturers sp ecifications. |
| 903 | \\"(a) Supplying, installation, testing and commissioning of electric driven Terrace Fire Pump suitable for automatic operation and co nsisting of following, complete in all respects, as required : ( Terrace Fire Pump ). (b) Horizontal type, multistage, centrifugal split casing pump of cast iron body and bronze impeller with stainless steel shaft, mec hanical seal conforming to IS : 1520. (c) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 clas s of protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS : 325. (d) M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (e) Suitable cement concrete foundation duly plastered and with anti vibration pads.\\" |
| 904 | 450 lpm at 35 m Head |
| 905 | Supply, Installation, Testing & Commissioning of 6 core Single mode OS2 Unitube Armoured Optical fiber cable on surface / recess / i n existing pipe / open duct complete etc as required : The Fiber should be OS2 Single Mode Optical Fiber Cable of Size 9/125µm. Out door Corrugated Steel tape Complies to ANSI/TIA-568.3-D, ITU-T G652.D, Telcordia GR-20, IEC 60794-2, 60794-3-10, Tensile Strenght : 3000N and Crush Resistance : 3000N, HDPE Jacket. Complaint to RoHS Directive 2011/65/EU and (EU) 2015/863 and the OEM should have I SO 9001:2015, ISO 14001:2015, ISO 45001:2018, ISO 27001 and should have a certified PMP®or RCDD, CDCP and ITIL on the OEM’s payroll sitting in India whose services can be utilized for this project. Approved Makes: Panduit / 3C3 / Corning / Leviton /Equivalent |
| 906 | Supply, Installation, Testing & Commissioning of 12 Core Fiber Loaded LIU Drawer Type and Compact LIU. Consist of Top Cover and Bott om Panel, Body Material : SPCC Black Powder Coating, Dimensions (mm) : 482 X 250 X 1U, 4 Nos. of 20 mm diameter at the rear for Cabl e Entry, 19” LIU Loaded with Singlemode OS2 LC Adapters & LC Type LSZH Pigtails should meet IEC 61034-1 ,IEC-60332-1, IEC-60754-1, I nsertion loss <= 0.20 dB, Return Loss : UPC>=50db should support operating temperature from -25°C to +70\\"C , Repeatability: <= 0.2 d b 1000 times mating cycles along with Spilce tray, cable holder and 4 nos of cable entry exist point with rubber gurment along with the LIU, SPCC Powder Coated, 2-Cut Out type, 1U, RoHS Complied, Meets ANSI/TIA 568.3-D. etc complete as required. Complaint to RoHS Directive 2011/65/EU and (EU) 2015/863. OEM should have ISO 9001:2015, ISO 14001:2015, ISO 45001:2018 and ISO 27001 and shall be ESG Silver or better rated Approved Makes: Panduit / 3C3 / Corning / Leviton /Equivalent |
| 907 | Supply, Installation, Testing & Commissioning of 24 Core Fiber Loaded LIU Drawer Type and Compact LIU. Consist of Top Cover and Bott om Panel, Body Material : SPCC Black Powder Coating, Dimensions (mm) : 482 X 250 X 1U, 4 Nos. of 20 mm diameter at the rear for Cabl e Entry, 19” LIU Loaded with Singlemode OS2 LC Adapters & LC Type LSZH Pigtails should meet IEC 61034-1 ,IEC-60332-1, IEC-60754-1, I nsertion loss <= 0.20 dB, Return Loss : UPC>=50db should support operating temperature from -25°C to +70\\"C , Repeatability: <= 0.2 d b 1000 times mating cycles along with Spilce tray, cable holder and 4 nos of cable entry exist point with rubber gurment along with the LIU, SPCC Powder Coated, 2-Cut Out type, 1U, RoHS Complied, Meets ANSI/TIA 568.3-D. etc complete as required. Complaint to RoHS Directive 2011/65/EU and (EU) 2015/863. OEM should have ISO 9001:2015, ISO 14001:2015, ISO 45001:2018 and ISO 27001 and shall be ESG Silver or better rated Approved Makes: Panduit / 3C3 / Corning / Leviton /Equivalent |
| 908 | Supply, Installation, Testing & Commissioning of OFC Patch Cord, SM (OS2), Duplex LC-LC, PC Type, 3M, LSZH Fiber Optic Single Mode O S2 Patch Cords are offered in LSZH Jackets having a protective layer of Metal braiding is adopted, which has excellent side pressure resistance, flexibility and bending performance. Having an lnsertion Loss : <= 0.2 db, Return Loss: UPC>=50db, Tensile strength(N) : 500 and Crush Resistance(N/100mm) : 3000. Complaint to RoHS Directive 2011/65/EU and (EU) 2015/863. Approved Makes: Panduit / 3C3 / Corning / Leviton /Equivalent |
| 909 | Supply, Installation, Testing & Commissioning of Category 6A U/UTP LSZH Cable, Flame Rating IEC 60332-1, 23 AWG solid copper conduc tors in accordance to TIA/EIA 568.2-D (Category 6) & ISO/IEC 11801 2nd ed(Class Ea), ETL 04-Connector Channel Verified with MTPL, te sted @600 Mhz or more, with HDPE insulation of individual conductor and over all Dia of 5.9 ± 0.3 mm with Cross-filler and cable sha ll not have any kind of Non Metallic Barrier Tape or Metallic Shield inside for Connectivity of Hub room to End Point on surface / recess / in existing pipe / open duct complete etc as required. Approved Makes: Panduit / 3C3 / Corning / Leviton /Equivalent |
| 910 | Supply, Installation, Testing & Commissioning of Category 6A RJ45 Unshielded Modular Jack, Keystone information outlet (I/O) in acco rdance with ANSI/TIA 568.2-D, IEC 60603-7-4 2nd Edition, ISO/IEC 11801, ROHS Compliant. The I/O should have minimum 750 mating cycle and 200 insertion cycle and ETL 04-Connector Channel Verified with MTPL, tested @ 600Mhz for Data, Voice, CCTV & Wi-Fi at Field End complete etc as required. Approved Makes: Panduit / 3C3 / Corning / Leviton /Equivalent |
| 911 | Supply, Installation, Testing & Commissioning of 24 Port Unshielded Cat6A Patch Panel, Loaded with Category 6A RJ45 Unshielded Modu lar Jack, Keystone information outlet (I/O) in accordance with ANSI/TIA 568.2-D, IEC 60603-7-41 2nd Edition, ISO/IEC 11801. The I/O should have minimum 750 mating cycle and 200 insertion cycle and ETL 04-Connector Channel Verified with MTPL up to 635 MHz, 1U heigh t, Black with integrated cable support bar, clear label marks and earthing plug for UTP cable termination at rack end complete etc a s required.OEM should have ISO 9001:2015, ISO 14001:2015, ISO 45001:2018, ISO 27001, ESG Silver or better rated, RoHS Directive 2011 /65/EU and (EU) 2015/863 and ASTM B 117 Certified. Approved Makes: Panduit / 3C3 / Corning / Leviton/ Equivalent |
| 912 | Supply, Installation, Testing & Commissioning of CAT6A U/UTP, 24 AWG, 1 Mtrs Patch Cord Patch cord, Cable Diameter 7.30 ± 0.50 mm. C omplies to the Standard ANSI/TIA/EIA-568.2-D Standard. Supports Data Networks Speeds Up to 10/100/1000- Base-T and 10G Base-T. LSZH Jacket for reduced toxic gasses emitted during combustion, RJ45, 8P8C, 3 Prong Design for accurate termination, 50µ\\" Gold Plated Con tacts , 100% Factory Tested, Transparent Boot Cable Assemblies.ETL Verified 4 connector channel performance with MTPL up to 635 MHz. Complaint to RoHS Directive 2011/65/EU and (EU) 2015/863. OEM should be a member of BICSI and TIA. Approved Makes: Panduit / 3C3 / Corning / Leviton /Equivalent |
| 913 | Supply, Installation, Testing & Commissioning of CAT6A U/UTP, 24 AWG, 2 Mtrs Patch Cord Patch cord, Cable Diameter 7.30 ± 0.50 mm. C omplies to the Standard ANSI/TIA/EIA-568.2-D Standard. Supports Data Networks Speeds Up to 10/100/1000- Base-T and 10G Base-T. LSZH Jacket for reduced toxic gasses emitted during combustion, RJ45, 8P8C, 3 Prong Design for accurate termination, 50µ\\" Gold Plated Con tacts , 100% Factory Tested, Transparent Boot Cable Assemblies.ETL Verified 4 connector channel performance with MTPL up to 635 MHz. Complaint to RoHS Directive 2011/65/EU and (EU) 2015/86. OEM should be a member of BICSI and TIA. Approved Makes: Panduit / 3C3 / Corning / Leviton /Equivalent |
| 914 | Supply, Installation, Testing & Commissioning of CAT6A RJ45 Connectors at field end for Wi-Fi and CCTV Cameras. Approved Makes: Pan duit / 3C3 / Corning / Leviton /Equivalent |
| 915 | Supply, Installation, Testing & Commissioning of 1, 2, and 4 Port face plate, British Style with Shutter, 2 Plate system clear finis h with transparent labelling, ABS-UL94-V0, ROHS Compliant, in accorandce with standards like ANSI/TIA-568.2-D, ISO/IEC 11801:2002 & ISO/IEC 60603-7 white for I/O fixing. Approved Makes: Panduit / 3C3 / Corning / Leviton /Equivalent |
| 916 | Supply, Installation, Testing & Commissioning of 42U (600x1000) floor mount Networking rack with fans , 2 cable managers , stationa ry shelf , 2 Nos. of hardware pkts. Approved Makes: SMC / 3C3 / APW / Rittal /Equivalent |
| 917 | Supply, Installation, Testing & Commissioning of 18U Networking rack with fans , 2 cable managers , stationary shelf , 2 Nos. of har dware pkts. Approved Makes: SMC / 3C3 / APW / Rittal/Equivalent |
| 918 | Supply, Installation, Testing & Commissioning of Power Distribution Unit with 1.5 Meter long cords & 06 Socket of 5 Amp. Approved Ma kes: SMC / 3C3 / APW / Rittal/ Equivalent |
| 919 | Supply, Installation, Testing & Commissioning of Power Distribution Unit with 1.5 Meter long cords & 12 Socket of 5/15 Amp. Approved Makes: SMC / 3C3 / APW / Rittal/ Equivalent |
| 920 | Supply, Installation, Testing & Commissioning of Core Switch with switching capacity of 800 Gbps, forwarding performance of 600 Mpps with 24 x 10G SFP+ and 6x25G ports with, 1 x RJ45 Ethernet Management port, Stacking to be done through VSF or equivalent technolo gy, 120K MAC Address, Jumbo frames: 9K bytes, Routing Table: 16K, ACL Table: 3K, L3 Interface: Max 2K, Static Routing, PBR, Root Gua rd, BPDU Guard, DHCP Relay Option 82, DHCP client/server, DVMRP, PIM-DM, PIM-SM, PIM-SSM, OSPFv3, VRRP, Syslog, Port loopback detect ion, LLDP, Anti ARP/NDP Cheat, Anti ARP/NDP, Working Temperature :0°C~50°C. or better. Approved make - Cisco / Alcatel / TP-Link / Arista / Extreme/Equivalent |
| 921 | Supply, Installation, Testing & Commissioning of 24 Port PoE Access Switches with switching capacity of 128 Gbps, forwarding perform ance 95 Mpps, having 24 x 10/100/1000BASE-T PoE plus (RJ45) with minimum PoE budget of 370W and 4x 10G SFP+ uplink ports,16K MAC Add ress, Jumbo frames: 9K bytes, Static Routing, PBR, Root Guard, BPDU Guarded Relay Option 82, Option 37/38, DHCP client, DHCP server, IGMP Snooping (V1,v2,v3), MLD v1/ v2 Snooping, Classification based on ACL (Access Control List), VLAN ID, COS, TOS, DSCP), Syslog (IPv4/IPv6), ULDP, LLDP, IP ACL, Authentication, Authorization, Accounting, DAI, Working Temperature :0°C~45°C. or better. Certifica tions - UL, CE, FCC, IEC - 62443-4-1 Cyber security certification. Approved make - Cisco / Alcatel / TP-Link / Arista / Extreme/Equ ivalent |
| 922 | Supply, Installation, Testing & Commissioning of 10G Single Mode SFP+ fiber Modules. Approved make - Cisco / Alcatel / TP-Link / A rista / Extreme/ Equivalent |
| 923 | Supply, Installation, Testing & Commissioning of Wireless Controller & NMS . It should support Centralized Management for WLAN & LA N Infrastructure . The Solution should support 25 AP's. The solution should expandable upto 300 AP's & 50 Switches. The Controller s hould 2 x 10/100/1000 Mbps Ethernet Ports, Quad-Core A72 @ 1.2 GHz Processor, 1 x 1 USB 3.0 Port, 300 Maximum Number of WLAN Groups, Multi-Site Management, Operating temp. 0 to 40 degree, Operating Humidity: 10–90% RH non-condensing. Certification: CE, FCC, RoHS. Approved make - Cisco / Alcatel / TP-Link / Arista / Extreme/ Equivalent |
| 924 | Supply, Installation, Testing & Commissioning of Wireless Indoor Access Point. The AP should support 802.11ax with aggregated throug hput of 5 Gbps.Signal Rate: 5 GHz: Up to 4804 Mbps & 2.4 GHz: Up to 574 Mbps. It should have 1× 2.5 Gigabit Ethernet (RJ-45) Port (s upports IEEE802.3at PoE). It should support Automatic Channel Assignment, Wireless Mac Address Filtering, Beamforming, 16 SSIDs, Reb oot Schedule, WPA2, WPA3, 802.1X. Antennas: 2.4 GHz: 2x 4 dBi, 5 GHz: 4x 5 dBi, UL/DL OFDMA support, Transmission Power: <23 dBm(5 G Hz, , band1 & band2, EIRP), Operating temp. 0 to 40 degree, Operating Humidity: 10–90% RH non-condensing. Certification: CE, FCC, Ro HS. Approved make - Cisco / Alcatel / TP-Link / Arista / Extreme/ Equivalent |
| 925 | Supply, Installation, Testing & Commissioning of Analog CLI Instrument having CLI, Redial, flash, Incoming & Outgoing call details e tc as required. Approved Makes: Panasonic / Coral / Beetel / Alcatel/Equivalent |
| 926 | Supply, Installation, Testing & Commissioning of 100 Pair IDF complete with box, module, back mount frame etc. for Raiser Cable Term ination. Approved Makes: Gleam Light / Krone / IDIS / Synergy / SMC/Equivalent |
| 927 | Supply, Installation, Testing & Commissioning of 100 Pair MDF complete with box, module, back mount frame etc. for Connectivity Cabl e Termination. Approved Makes: Gleam Light / Krone / IDIS / Synergy / SMC/Equivalent |
| 928 | Supply, Installation, Testing & Commissioning of 20 Pair Armoured Jelly Filled Cable, Solid Annealed Bare Copper. The Cable Core thu s formed is filled with suitable water resistance compound. Approved Makes: Polycab / Delton / Finolex / Synergy / Capital/Equivale nt |
| 929 | Supply, Installation, Testing & Commissioning of 2 Pair PVC Telephone Cable, Solid Annealed Bare Copper. Approved Makes: Polycab / Delton / Finolex / Synergy / Capital/Equivalent |
| 930 | Supply, Installation, Testing & Commissioning of 0.5mm Single Pair Jumper Cable. |
| 931 | Expansion/Intergration of existing Exchange (Hi-path 3800) to connect the new user including cards, license and cabling etc. to fill ed the current requiement of new Building. |
| 932 | Supply, Installation, Testing & Commissioning of 4MP Dome camera with 1/2.8” Low Illumination Progressive Scan CMOS Sensor, Effectiv e pixels 2560(H) x 1440(V), Color: 0.001Lux @ (F1.2, AGC ON), 0.014 Lux @ (F1.4, AGC ON), 0 Lux with IR, Quad Streaming, Up to 120 dB, TWDR, Shutter Speed: Auto, Slow Shutter, (1/5 sec ~ 1/100,000 sec Adjustable), H.265, H.264, M-JPEG Video compression, White bal ance, Backlight Compensation, Privacy Mask, 3.6 mm Fixed Lens, MicroSD card slot support up to 512GB, Motion:Set Detection Area, Pe riod, Can Set Multi-Level Sensitivity, tamper detection, Event Actions: Enable Alarm Out, Send Email, Start Recording, Play Customiz ed Audio Warning, IR range upto 40mtrs, ONVIF Profile S, G, & T, PoE, CE, FCC , BIS, Cyber Security: ISO/IEC 27400 OWASP Level 2 of ASVS v4.0 Appendix C Certificate No. STQC/IOTSCS/0922/001U1, IP67 & IK10 Complaint. Approved Makes : Bosch / Axis / Sparsh / Honeywe ll Enterprises / Pelco / CBC Ganz/Equivalent |
| 933 | Supply, Installation, Testing & Commissioning of 4MP Bullet camera with 1/2.8” Low Illumination Progressive Scan CMOS Sensor, Effect ive pixels 2560(H) x 1440(V), Color: 0.001Lux @ (F1.2, AGC ON), 0.014 Lux @ (F1.4, AGC ON), 0 Lux with IR, Quad Streaming, Up to 12 0 dB, TWDR, Shutter Speed: Auto, Slow Shutter, (1/5 sec ~ 1/100,000 sec Adjustable), H.265, H.264, M-JPEG Video compression, White b alance, Backlight Compensation, Privacy Mask, 3.6 mm Fixed Lens, MicroSD card slot support up to 512GB, Motion:Set Detection Area, Period, Can Set Multi-Level Sensitivity, tamper detection, Event Actions: Enable Alarm Out, Send Email, Start Recording, Play Custom ized Audio Warning, IR range upto 40mtrs, ONVIF Profile S, G, & T, PoE, CE, FCC , BIS, Cyber Security: ISO/IEC 27400 OWASP Level 2 o f ASVS v4.0 Appendix C Certificate No. STQC/IOTSCS/0922/001U1, IP67 Complaint. Approved Makes : Bosch / Axis / Sparsh / Honeywell En terprises / Pelco / CBC Ganz/Equivalent |
| 934 | Supply Installation Testing and Commissioning of 32 Channel NVR, Up to 4K Resolution 1 HDMI and 1 VGA independent outputs provided , 4K resolution, VGA output upto 1920 × 1080, Support H.265/H.264, Network Access Bandwidth 400 Mbps, 2 or more SATA Hard Disk slots and capacity of each HDD upto 10TB or better, 3 × USB, 1 x RJ-45 10 /100/1000 Mbps Ethernet interface, 1/2/4/6/8/9/10/16/25/32 image display, Certifications: Safety: CE, FCC, BIS Registered, including connection configuration etc complete as required. Approved Makes : Bosch / Axis / Sparsh / Honeywell Enterprises / Pelco / CBC Ganz/Equivalent |
| 935 | Supply , Installation , Testing and commissioning of Surveillance Garde 6TB SATA Hard Disk for above VMRs, including fixing accesso ries and cable termination with required, complete in all respect as per instruction of engineer in-charge. Recording shall be calcu lated at 2MP, 25fps for 30 days. Approved Makes: WD / Segate / Toshiba / HP/Equivalent |
| 936 | Supply , Installation , Testing and commissioning of 10 Meter HDMI Gold plated Cable Approved make: Extron / Aten / Aktan / Crestro n / Honeywell/Equivalent |
| 937 | Supply , Installation , Testing and commissioning of 65” Display Panel having contrast ratio 1200:1, Aspect Ratio: 16:9, Native Res olution : 3,840 X 2,160 , Brightness : 400 nits, Viewing Angle (H X V): 178 X 178, Surface Treatment : Hard coating (3H) Anti-glare Treatment of the Front Polarizer (Haze 1 % Typ.), Speakers : 10 w x2, Orientation: Landscape & Portrait, Input/Output: HDMI (3), RF, Composite ,Data Point : RJ45, USB, WIFI, BLUETOOTH, Operation Temperature 0°c to 40°c , Operation Humidity: 10% to 80%, Power Suppl y: 100-240V~, 50/60Hz, Remote on/off, Source Change, Volume, Generate Reports and Email notifications. Accessories Remote Control, P ower Cord, User Guide , BIS /ROHS/CE/FCC and along with wall mount ect all required. Approved make: Samsung / Aaztec / Sony / Christ ie / Daktronics/Equivalent Please Enable Macros to View BoQ information |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
