|
| 1 | DETAILED ESTIMATE |
| 2 | 10.1:Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 3 | 10.16.1:Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes |
| 4 | OD467163/2025-2026:Providing and fixing galvanised iron profile sheets (size,shape and pitchof corrugation as approved by Engineer incharge) .35 mm(+.05%) .total coated thickness with zinc coating 120 grams per sqm as per IS277,240mpa steel grade ,5-7 microns epoxy primer on both sides of sheet and polyester top coat 15-18 Microns.sheet should have protective guard film of25 microns minimum to avoid scratches during trasportation and should supplied in single length up to 12 metre or as desired by Engineer -in-charge .The sheet shall fixed using self drilling /selftapping screws of size (5.5*55mm) with EDPM seal,complete up to any pitch in horizontal/vertical or curved surface,excluding the cost of purlins,rafters and trusses and including cutting to size and shape wherever required.Detailsof cost for216.14sqm (External diamensions of plinth .Area of roof =20.20*107m =216.14sqm.sheet used =20nos*10.70m*1.06m=226.84sqm and 3%wastage=6.81Total 233.65sqm. |
| 5 | OD467164/2025-2026:Providing and fixing150 mm dia PVC gutter pvc rectangular semicircular sectionincluding fitting with 20*5 mm ms flat supporters at .75 m interval including cost and conveyance and labourcharges etc complete |
| 6 | 4.1.3:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-III)derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 7 | 13.61.1:Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work |
| 8 | 13.112.1:Finishing walls with Premium Acrylic Smooth exterior paint with Siliconeadditives of required shadeOld work (Two or more coats applied @ 1.43 ltr/ 10 sqm) over existing cementpaint surface |
| 9 | 13.99.1:Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :One or more coats on old work |
| 10 | 21.1.1.1:Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately):For fixed portionAnodised aluminium (anodised transparent or dyed to required shade according to IS : 1868, Minimum anodic coating of grade AC 15) |
| 11 | 21.3.1:Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) |
| 12 | 11.41.2:Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600 x 600 mm. Please Enable Macros to View BoQ information |
