|
| 1 | HSR Item 11.78-Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade.HSR Rate(Rs.) 31.00 Through Rate |
| 2 | HSR Item 2.B0156- B0156. Common burnt clay F.P.S. (non modular)bricks tile class designation 10HSR Rate(Rs.) 4465.00 Rate |
| 3 | HSR Item 6.30.6-Centering and shuttering including strutting, propping etc. and removal of form for 6. Columns, Pillars, Piers, Abutments, Posts and StrutsHSR Rate(Rs.) 262.00 Through Rate |
| 4 | HSR Item 9.34.6-Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm ( plus 0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : 6. Gutter (600 mm over all girth)HSR Rate(Rs.) 717.00 Through Rate |
| 5 | HSR Item 9.57.2-Providing and fixing on wall face Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 2. 110 mm diameterHSR Rate(Rs.) 200.00 Through Rate |
| 6 | HSR Item 9.59.2-Providing and fixing Unplasticised -PVC pipe clips of approved design to Unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 2. 110 mm HSR Rate(Rs.) 147.00 Through Rate |
| 7 | HSR Item 11.5.3-12 mm cement plaster of mix : 3. 1:4 (1 cement: 4 fine sand)HSR Rate(Rs.) 113.00 Through Rate |
| 8 | HSR Item 9.32.1-Providing and fixing UV stabilised fibreglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated `J` or `L` hooks, bolts and nuts 8mm dia.G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified. 1. 2 mm thick corrugated (2.5\\" or 4.2\\" or 6\\") or step-down (2\\" or 3\\" or 6\\" ) as specifiedHSR Rate(Rs.) 877.00 Through Rate |
| 9 | HSR Item 30.9-Regarding terracing of mud phaska covered with tiles or brick, in cement mortar by dismantling tiles or bricks, removing mud plaster, preparing the surface of mud phaska to proper slope, relaying mud plaster gobri leaping and tiles or bricks, grouted in cement mortar 1:3 (1 cement : 3 fine sand), including replacing unserviceable tiles or bricks with new ones and disposal of unserviceable material to the dumping ground (the cost of the new tiles or brick excluded), all complete as per direction of Engineer-in-Charge.HSR Rate(Rs.) 219.00 Through Rate |
| 10 | HSR Item 11.60-Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.HSR Rate(Rs.) 59.00 Through Rate |
| 11 | HSR Item 9.33-Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm ( plus 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length up to 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete up to any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.HSR Rate(Rs.) 504.00 Through Rate |
| 12 | HSR Item 9.34.1-Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm ( plus 0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : 1. Ridges plain (500 - 600mm)HSR Rate(Rs.) 311.00 Through Rate |
| 13 | HSR Item 5.23.1-Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. 1.Nominal concrete 1:1.5:3 or richer mix (i/c equivalent design mix)HSR Rate(Rs.) 1287.00 Through Rate |
| 14 | HSR Item 6.15.1-Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor four level, excluding cost of centering, shuttering, finishing and reinforcement : 1. 1:1.5:3 (1 cement : 1.5 coarse sand(zone- III) : 3 graded stone aggregate 20 mm nominal size)HSR Rate(Rs.) 5969.00 Through Rate |
| 15 | HSR Item 6.33.6-Steel reinforcement for R.C.C. work, where not included in the complete rate of RCC, including straightening, cutting, bending, placing in position, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. complete in all respect below plinth level Note: Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work , excluding overlaps.Wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods of binding & placing shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement. 6. Thermo-Mechanically Treated bars of grade Fe-500D or moreHSR Rate(Rs.) 66.00 Through Rate |
| 16 | HSR Item 13.30.1-Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. 1. Hot finished welded type tubesHSR Rate(Rs.) 105.00 Through Rate |
| 17 | HSR Item 9.58.5.2-Providing and fixing on wall face Unplasticised - PVC moulded fittings/ accessories for Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 5.2.Bend 87.5°110 mm bendHSR Rate(Rs.) 93.00 Through Rate |
| 18 | HSR Item 11.96.1-Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: 1. New work (Two or more coats applied @ 1.43 litre/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)HSR Rate(Rs.) 85.00 Through Rate |
| 19 | HSR Item 23.3.6.5-COPPER WIRING IN PVC CONDUIT(SURFACE/RECESS) 6.5. Wiring main and sub mains in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in PVC Conduit etc as required. 1 run of Size 10 Sqmm (1/3.50 mm)HSR Rate(Rs.) 346.00 Through Rate |
| 20 | HSR Item 24.1.6-EARTHING AND LIGHTENING ARRESTOR6. Supplying and laying 25mm x 3mm G.I. strip at 0.5 metre below ground as strip earth electrode including soldering etc. as required.HSR Rate(Rs.) 47.00 Through Rate |
| 21 | HSR Item 23.4.1.1-COPPER WIRING WITH MODULAR SWITCHES IN PVC CONDUIT (SURFACE/RECESS) 1.1.Wiring for Light/Fan/call bell point with modular type switch/socket and GI box, Modular type face plate etc in 1.5 sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick PVC conduit pipe. Group AHSR Rate(Rs.) 520.00 Through Rate |
| 22 | HSR Item 23.4.4.1-COPPER WIRING WITH MODULAR SWITCHES IN PVC CONDUIT (SURFACE/RECESS) 4.1.Wiring in PVC conduit system for 3-pin 5amp. Plug point by using 2 no 1.5 sqmm FRLS copper wire and 1 no 1.5 Sqmm FRLS copper wire , including providing 1 no 5/6 Amp 3/5 pin Modular type socket and 1 no 5/6 Amp Modular type switch required GI Box ,modular face plate etc complete as required Group AHSR Rate(Rs.) 725.00 Through Rate |
| 23 | HSR Item 23.4.5.1-COPPER WIRING WITH MODULAR SWITCHES IN PVC CONDUIT (SURFACE/RECESS) 5.1.Wiring in PVC conduit system for 3-pin 15amp. Plug point by using 2 no 4 sqmm FRLS copper wire and 1 no 4 Sqmm FRLS copper wire for earthling , including providing 1 no 15/16 Amp 3/6 pin Modular socket and 1 no 15/16 Amp Modular switch required GI Box , modular face plate etc complete as required Group AHSR Rate(Rs.) 999.00 Through Rate |
| 24 | HSR Item 23.3.6.1-COPPER WIRING IN PVC CONDUIT(SURFACE/RECESS) 6.1. Wiring main and sub mains in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in PVC Conduit etc as required. 1 run of Size 1.50 Sqmm(1/1.40mm)HSR Rate(Rs.) 88.00 Through Rate |
| 25 | HSR Item 23.3.6.3-COPPER WIRING IN PVC CONDUIT(SURFACE/RECESS) 6.3. Wiring main and sub mains in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in PVC Conduit etc as required. 1 run of Size 4 Sqmm (1/2.24mm)HSR Rate(Rs.) 144.00 Through Rate |
| 26 | HSR Item 23.8.1.12-FITTING AND ACCESSORIES 1.12.Providing and fixing Piano type accessories of approved make in existing box and Bakelite sheet including fixing and making necessary connections, complete in all respect. Bakelite angle/straight button holder large size.HSR Rate(Rs.) 46.00 Through Rate |
| 27 | HSR Item 23.8.11.1-FITTING AND ACCESSORIES 11.1.Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. 5 amp 1 way switch HSR Rate(Rs.) 41.00 Through Rate |
| 28 | HSR Item 23.8.11.4-FITTING AND ACCESSORIES 11.4.Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. 5 amp SocketHSR Rate(Rs.) 82.00 Through Rate |
| 29 | HSR Item 23.8.11.7-FITTING AND ACCESSORIES 11.7.Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. step type Fan Regulator 2 modules 300 wattHSR Rate(Rs.) 257.00 Through Rate |
| 30 | HSR Item 23.8.11.10-FITTING AND ACCESSORIES 11.10.Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. Blanking plateHSR Rate(Rs.) 18.00 Through Rate |
| 31 | HSR Item 23.22.4.5-MCCB ,DISTRIBUTION BOARDS,MCB`s, RCCB`s, CHANGE OVER etc. 4.5. Supply and erection of double door sheet steel enclosure distribution board suitable for MCBS and ELCBS etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work. TPN DB Horizontal type Double Door 4 way ( 8 incoming and 3phase*4 outgoing)HSR Rate(Rs.) 2707.00 Through Rate |
| 32 | HSR Item 23.22.5.1-MCCB ,DISTRIBUTION BOARDS,MCB`s, RCCB`s, CHANGE OVER etc. 5.1. Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- 6 amp. to 32 amp Single PoleHSR Rate(Rs.) 145.00 Through Rate |
| 33 | HSR Item 23.7.6.2-PVC CONDUIT PIPE ONLY (SURFACE OR RECESSED) FOR ELECTRICAL POINTS 6.2. Supply anderection of PVC CONDUIT ISI marked (Medium) recessed in wall/ceiling etc. including the cost of PVC bends, inspection boxes, iron hooks and cement concrete etc. complete in all respect up to the entire satisfaction of Engineer-in-Charge of work. PVC pipe of 25 mm dia.HSR Rate(Rs.) 32.00 Through Rate |
| 34 | HSR Item 23.8.10.4-FITTING AND ACCESSORIES 10.4.Providing and fixing GI concealed sheet metal boxes with inner and outer face plate including concealing the box in wall and fixing in position with inner plate and face plate with all labour and material required for the job complete in all respects. 6 ModulesHSR Rate(Rs.) 186.00 Through Rate |
| 35 | HSR Item 23.20-Fixing of LED Tube light/ 2*2 ft square panel fitting directly on wall /ceiling or false ceiling including making connections etc as requiredHSR Rate(Rs.) 67.00 Through Rate |
| 36 | HSR Item 23.23.2.2-MISCELLANEOUS 2.2. Supply of GI pipe(B-Class) for suspension rod of ceiling fan including threading if required. 20 mm diaHSR Rate(Rs.) 169.00 Through Rate |
| 37 | HSR Item 24.1.1-EARTHING AND LIGHTENING ARRESTOR1. Earthing with GL earth pipe 4.5 m long and 40 mm dia with masonry enclosures on the top etc. (but without charcoal or coke and salt) as required.HSR Rate(Rs.) 2721.00 Through Rate |
| 38 | HSR Item 24.1.2-EARTHING AND LIGHTENING ARRESTOR2. Extra for using salt and char coal/coke for pipe earth electrode as required.HSR Rate(Rs.) 652.00 Through Rate |
| 39 | HSR Item 23.22.5.8-MCCB ,DISTRIBUTION BOARDS,MCB`s, RCCB`s, CHANGE OVER etc. 5.8. Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- 40 amp to 63 amp. MCBs FOUR POLEHSR Rate(Rs.) 1291.00 Through Rate |
| 40 | HSR Item 20.71.2-Supply, erection, testing of Ceiling fans IS marked (as per IS code 374) with suitable GI pipe complete in all respects complete as per directions of Engineer-in-charge2. 56\\" (1400mm)HSR Rate(Rs.) 2361.00 Through Rate |
| 41 | NS Item -Supply of 18/20 watt rating 4 feet long LED Tube light Batten suitable for operation on 230 volt, 50 Hz supply. Make:- Havells or as per HPHC approved brand (NS). |
| 42 | NS Item -Supply and Erection of 50/60 watt LED Flood light suitable for operation on 230V ,50Hz complete the job in all respect . Make as per HPHC approved brands |
| 43 | NS Item -Supply and erection of 1.5 Sqmm ISI Marked, FSRL PVC Insulated, single core copper conductor cable. (HSR Sr. No. EL003) Make- as per brand list (Without GST). Please Enable Macros to View BoQ information |
