Tender For Construction Of Collectorate Building At Sambalpur, Phase-Ii., Sambalpur-Odisha

TDR : 54512139

Tender Notice
BOQ

3 Days Left

Sambalpur , Odisha

Tender Brief : Tender For Construction Of Collectorate Building At Sambalpur, Phase-Ii.

Document Fees
₹ 10000 /-

EMD
₹ 1937000.0 /-

Tender Value
₹ 19.36 Crore /-

Submission Date
12-03-2026

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	CIVIL WORKEarthwork in excavation in all types of soil for site leveling, foundation, pits, trenches and other civil works upto and including 1.5 metre lift and stacking the soil upto a lead of 100 metre and including dewatering, removing slush,shoring and strutting (as required), complete as per specification and as directed by the Engineer-In-Charge. ROAD
2	DRAIN
3	COMPOUND WALL
4	GATEWAY
5	Filling at all depth with available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 15cm in depth: consolidating each deposited layer by ramming and watering complete (lead upto 100m) as directed by the Engineer-In-charge. ROAD
6	DRAIN
7	COMPOUND WALL
8	GATEWAY
9	Supplying and filling in foundation trenches and plinth, ditches with sand well watered and rammed in layers not exceeding 23 cm. In depth with all lead and lift including cost, conveyance, loading, unloading, royalties and taxes of all materials, cost of all labour, sundries, T&P required for the work etc. complete in all respect as per specification and direction of Engineer-in-charge. ROAD
10	DRAIN
11	COMPOUND WALL
12	GATEWAY
13	Cement concrete of proportion (1:4:8) in foundation and floors using 4cm size clean hard black crusher broken granite stone metal of approved quality and from approved quarry including hoisting, lowering and laying concrete in layers not exceeding 15 cm. (6\\") thick to the required level ramming, watering, curing etc. complete including cost, conveyance, royalties of all materials with all labour and T&P required for the work etc. complete in all respect and as per the direction of the Engineer-in-charge.DRAIN
14	COMPOUND WALL
15	GATEWAY
16	Fly Ash brick masonry in cement mortar (1:6) in foundation & plinth using Fly Ash bricks of 25 x 12 x 8 cm size having a crushing strength of not less than 75 kg./sqcm with dimensional tolerance ± 2% including splays cutting circular moulding chamfering and corbelling and similar such type of works with all necessary projections watering and curing after immersing the bricks in water at least for six hours before use including cost, conveyance, royalties of all materials with all labour,labour cess and T & P required for the work complete in all respect as per direction of Engineer-in-Charge.COMPOUND WALL
17	GATEWAY
18	Fly Ash brick masonry in cement mortar (1:6) in super structure using Fly Ash bricks of 25 x 12 x 8 cm size having a crushing strength of not less than 75 kg./sqcm with dimensional tolerance ± 2% including splays cutting circular moulding chamfering and corbelling and similar such type of works with all necessary projections watering and curing after immersing the bricks in water at least for six hours before use including cost, conveyance, royalties of all materials with all labour,labour cess and T & P required for the work complete in all respect as per direction of Engineer-in-Charge.COMPOUND WALL
19	GATEWAY
20	Providing, lifting, hoisting and laying Reinforced cement concrete of M-25 grade as per approved designs and drawings having a minimum compressive strength (in work test) 250 Kg. / Square cm. in 15 cm. cubes at 28 days after mixing and test conducted in accordance with I.S. 516 using 12 mm. to 20 mm. size black hard crushed broken granite stone chips and screened and washed sharp sand for mortar of approved quality from approved quarry, washed and cleaned ( 20mm. size chips not to exceeds 25 % ) to be mixed in concrete mixture with Portland slag cement (PSC) including hoisting, lowering, laying and compaction concrete by using vibrators, watering and curing for 28 days, centering and shuttering then after dismantling and removing debris from the work site and finishing the exposed surface smooth providing grooves or beads wherever necessary including cost, conveyance, loading, unloading, royalties and taxes of all materials and cost of all labours, sundries, T & P required of the work etc. complete in all respect as directed by the Engineer-in-Charge. But excluding cost and conveyance of M.S. rods or Tor steel and binding wires and labour charges for straightening, cutting, bending etc. of M.S. rods or tor steel tying the grills and placing in proper position. DRAIN BASE
21	COMPOUND WALL
22	GATEWAY
23	GATEWAY
24	DRAIN WALL
25	COMPOUND WALL
26	COPING BEAM
27	GATEWAY
28	COMPOUND WALL
29	COPING BEAM COMPOUND WALL
30	PLINTH BEAMCOMPOUND WALL
31	GATEWAY
32	DRAIN SLAB
33	SLAB GATEWAY
34	Supplying Cutting, straightening coiled or bent up M.S. Rod or tor steel of primary steel producers such as SAIL / Tiscon / RINL / JINDAL STEEL / SHYAM STEEL (grade Fe-500D) etc. including bending, binding, welding, wastage & over lapping and jointing if necessary and tying the grills and placing in position as required for R.C.C. Work and for providing fan hooks as required, hoisting, lowering, laying including cost, conveyances of M.S. Rod or tor steel and binding wires of 18 to 20 gauge and labour required for the work for bending, binding and tying the grills in all floors with labour cess etc. (payment will be made on standard weight of B.I.S. for M.S. Rods or tor steel only) etc. complete as per specification & direction of Engineer-in-charge. DRAIN
35	COMPOUND WALL
36	GATEWAY
37	Construction of granular sub-base by providing Close graded Granular subbase Grading-III material as per table 400-1, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density complete as per Clause 401 of MOSRT&H Specifications for Road & Bridge works (4th Revision)ROAD
38	Supplying and fixing of 80mm thick cement concrete interlocking paver block of M-40 grade of approved make, design, colour and size made by Block making machine with proper compaction laid in required pattern etc. complete in all respect conforming to IRC SP-63:2018.ROAD
39	Supplying & fixing of pre cast kerb stone of size 600mm x 300mmx150mm of M-30 grade of approved make desgin ,colour & size made by block making machine with proper compaction fixed in required pattern etc.complete in all respect conforming to IS 5758:1984.ROAD
40	Supplying, fitting and fixing of two track UPVC sliding window of approved make with 6mm thick glass of approved quality complete with frame. shutters and all Fitting and fixtures etc. complete as per direction of Engineer-in-charge (Make-FENESTA/ Koemmerling/ Saint Gobain/ Prominance)BASEMENT FLOOR
41	TERRACE FLOOR
42	GATEWAY
43	Supplying, fitting & fixing in all floors of M.S. grills, grill gates, M.S. gates, garage door, collapsible gates with top and bottom rails, steel windows, critical frames for windows, stair case and parapet railing made out of M.S Square bar/ flat including stair case hand railing with 40mm. dia G.I.pipe etc. including painting two coats over a coat of redoxide primer as per approved drawing and design with cost of all materials & labour, labour cess, T&P, sundries etc. complete in all respect as per specification & direction of the Engineer-in-Charge.BASEMENT FLOOR
44	TERRACE FLOOR
45	COMPOUND WALL
46	GATEWAY
47	Ventilator Casement window single panel with or without fixed panel with S.S. 304 friction hinges as per size and weight of sash, single point locking zinc alloy (zamak) powder coated handles.DSR VOL-I, SL NO-9.147.D1 ,Page no-660. Using R1 serieswith frame (33mm&above)x (35mm&above) & sash/ mullion (33mm& above) x (50 mm & above). (Height upto 0.90 metre).BASEMENT FLOOR
48	Providing 12 mm thick cement plaster with cement mortar of mix (1:6) with screened and washed sharp sand for mortar and finished smooth to the rough surface of walls in all heights after racking out joints including watering and curing, rounding of corners, providing grooves where ever necessary with cost, conveyance, royalties of all materials with cost of all labour,labour cess, T&P, and scaffolding required for the work etc. complete in all respect as directed by the Engineer in charge. COMPOUND WALL
49	GATEWAY
50	Providing 16 mm thick cement plaster with cement mortar of mix (1:6) with screened and washed sharp sand for mortar and finished smooth to the rough surface of walls in all heights after racking out joints including watering and curing, rounding of corners, providing grooves where ever necessary with cost, conveyance, royalties of all materials with cost of all labour,labour cess, T&P, and scaffolding required for the work etc. complete in all respect as directed by the Engineer in charge. GATEWAY
51	Providing 6 mm thick cement plaster with cement mortar of mix (1:4) with screened and washed sharp sand for mortar and finished smooth to R.C.C. work after closed deep chipping & slurry treatment including watering and curing, rounding of corners, providing grooves where ever necessary with cost, conveyance, royalties of all materials with cost of all labour,labour cess, T&P, and scaffolding required for the work etc. complete in all respect as directed by the Engineer in charge.GATEWAY
52	Priming one coat with wall cement primer (water bound) to make an even finished surface in all floors and heights to wall surface of approved make and shade including sand papering, applying putty wherever necessary & cost of scaffolding, staging charges with cost, conveyance, cost of all labour,labour cess T&P etc. complete as per the direction of the Engineer-in-charge.(Make: Asian/ Berger/ Dulux/ Nerolac or equivalent make duly approved by Engineer-in-Charge).BASEMENT FLOOR
53	GROUND FLOOR
54	FIRST FLOOR
55	SECOND FLOOR
56	THIRD FLOOR
57	TERRACE FLOOR
58	COMPOUND WALL
59	GATEWAY
60	Wall painting two coats with Antifungal weather coat paint (1st quality) exterior grade of approved make & approved shade over a coat of primer to make an even finished surface in all floors and heights with all scaffolding and staging charges including cost, conveyance, cost of all labours, T & P, sundries etc. as required for the work complete in all respect as per the direction of the Engineer-in-Charge.(Make: Asian/ Berger/ Dulux/ Nerolac or equivalent make duly approved by Engineer-in-Charge).BASEMENT FLOOR
61	GROUND FLOOR
62	FIRST FLOOR
63	SECOND FLOOR
64	THIRD FLOOR
65	TERRACE FLOOR
66	GATEWAY
67	Finishing plastered surfaces of walls with cement based wall putty (Water based) of approved make (JK White/ Birla white or equivalent make duly approved by Engineer-in-Charge) and finishing the surface smooth and even by sand papering to receive painting in walls, at all heights with staging wherever necessary with cost, conveyance, cost of all labour,labourcess, all T&P etc. required for the work complete in all respect as per the direction of the Engineer-in-charge. (Internal Surface) BASEMENT FLOOR
68	GROUND FLOOR
69	FIRST FLOOR
70	SECOND FLOOR
71	THIRD FLOOR
72	TERRACE FLOOR
73	Painting two coats with plastic emulsion paint with a approved quality primer to make an even finished surface in all floors and heights to wall surface of approved make and shade including sand papering, applying putty wherever necessary & cost of scaffolding, staging charges with cost, conveyance, cost of all labour,labour cess, T&P etc. complete as per the direction of the Engineer-in-charge.(Make: Asian/ Berger/ Dulux/ Nerolac or equivalent make duly approved by Engineer-in-Charge). (Internal Surface)BASEMENT FLOOR
74	GROUND FLOOR
75	FIRST FLOOR
76	SECOND FLOOR
77	THIRD FLOOR
78	TERRACE FLOOR
79	COMPOUND WALL
80	GATEWAY
81	Painting two coat with approved synthetic enamel paint to new wood & iron work over a coat of Red oxide primer including cost, conveyances, royalties of all materials and cost of all labour with T&P required for the work etc. complete as per specification & direction of Engineer in charge.(Make: Asian/ Berger/ Dulux/ Nerolac or equivalent make duly approved by Engineer-in-Charge). BASEMENT FLOOR
82	GROUND FLOOR
83	FIRST FLOOR
84	SECOND FLOOR
85	THIRD FLOOR
86	TERRACE FLOOR
87	COMPOUND WALL
88	GATEWAY
89	VDF FLOORING:- Providing and laying C.C. pavement of mix M-25 ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator, vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-in-charge. (The panel shuttering work shall be paid for separately).BASEMENT FLOOR
90	GROUND FLOOR
91	Waterproofing of Retaining wall:- Surface shall be grinded to remove all loose contamination, all tie rod holes shall be cut keeping 25mm depth and sealing the same with cement sand mortar admix with Rearm bond SBR 45 @ 10% of the cement weight. BASEMENT FLOOR
92	All construction joint shall be cut in V groove and sealing the same with cement sand mortar admix with Rearm bond SBR 45 @ 10% of the cement weight.BASEMENT FLOOR
93	Providing and laying Aquaarm SBS 3000X - SBS membre with cross laminated HDPE after application of single coat Aquaarm Tar primer over the prepared retaining wall. The membrane shall be terminated 100mm below from the top level with aluminium strip sealing with PU sealant. The membrane will have the following technical parameters: Tensile Strength : 220 Longitudinal 50 N/mm2 and 225 Tranversal 50N/mm2,. Elongation at break : 325% , Adhesion To concrete: >2 N/mm2.N.B. For Appliaction of SBS membrae is applied in retaining wall Dimple board is required. After Dimple board fixing Sand filling will be in Contractor scope.BASEMENT FLOOR
94	Protection with Dimple board: Providing and fixing 8mm dimple board over the SBS membrane using double sided tape at an interval of required space as protection layer before filling of earth. Precution shall be taken during laying of earth so that the dimple board shaould not fall dowm. BASEMENT FLOOR
95	Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-incharge. Size of Tile 1000x1000 mm.GROUND FLOOR
96	FIRST FLOOR
97	SECOND FLOOR
98	THIRD FLOOR
99	Supplying, fitting and fixing Anti-skid Mat finished Glazed vitrified tiles of premium grade having thickness 8mm to 10mm confirming to IS 13756 of size 600mm x 600mm Color / Printed series (Homogenous) of approved make (JOHNSON / SOMANY/ KAJARIA/ RAK) in floors on 20mm thick bed of C.M. (1:4)(1cement:4course sand) and filling the joint with white cement mixed with pigment to match the shades of the tileincluding cost of all materials, labour, labour cess, T&P etc. required for the work complete in all respect as directed by the Engineer in charge.GROUND FLOOR
100	FIRST FLOOR
101	SECOND FLOOR
102	THIRD FLOOR
103	Supplying, fitting and fixing vitrified tiles of premium grade having thickness 8mm to 10mm confirming to IS 13756 of size 600mm x 600mm Plain (Ivory) of approved make (JOHNSON / SOMANY/ KAJARIA/ RAK) in floors on 20mm thick bed of C.M. (1:4)(1cement:4course sand) and filling the joint with white cement mixed with pigment to match the shades of the tileincluding cost of all materials, labour, labour cess, T&P etc. required for the work complete in all respect as directed by the Engineer in charge. GATEWAY
104	Providing, fitting, fixing vitrified tiles of premium grade having thickness 8mm to 10mm confirming to IS 13756 of size 600mm x 600mm Plain (Ivory) of approved make (JOHNSON / SOMANY/ KAJARIA/ RAK) as directed by Engineer-in-charge in dados skirting and risers of steps on 12mm thick cement plaster (1:3) jointed with neat cement slurry mixed with pigment to match the shades of the tiles including rubbing and polishing etc. complete with cost, conveyance, royalties of all materials all labour,labour cess complete in all respects.GATEWAY
105	Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-incharge. GROUND FLOOR
106	FIRST FLOOR
107	SECOND FLOOR
108	THIRD FLOOR
109	Providing and fixing Ist quality Glazed vitrified tiles polished finish wall tiles conforming to IS: 15622 of size 600mm x 1200mm Plain (Ivory) of approved make (JOHNSON / SOMANY/ KAJARIA/ RAK) (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. Referance from .GROUND FLOOR
110	FIRST FLOOR
111	SECOND FLOOR
112	THIRD FLOOR
113	Fixing granite tiles of approved dimension area above 0.4 sqm (20mm thick) in floor, treads of steps and landing on 20mm thick bed of cement mortar (1:4) jointed with neat cement slurry mixed with pigment to match the shades of the tiles including rubbing and polishing etc. complete with cost, conveyance, royalties and taxes of all materials complete in all respects as per direction of Engineer-in-Charge.BASEMENT FLOOR
114	GROUND FLOOR
115	FIRST FLOOR
116	SECOND FLOOR
117	THIRD FLOOR
118	GATEWAY
119	WOODEN FLOORING:- Providing and laying in position 10.5mm thick Bruce Engineered wood Flooring of approved shade of size 1820mm x 190mm having smart lock tongue and groove joints to secure long lasting joint. The material comprising of three layers, Top layer is of genuine hardwood surface, the middle layer is of pine or spurce ribs laid transversely and the third layer is stabilizing bottom layer. The floor is finished on top with three course of formaldehyde free oil or five course of UV curved formaldehyde free lacquer. The boards are installed on foam and plastic on top of the under floor and stuck to one another using adhesive in the groove of the board all complete including all accessories (corner beading, Door sill)FIRST FLOOR
120	Providing 2.5cm thick A.S. Flooring with cement concrete (1:2:4) using 12mm size black hard granite crusher broken chips and screened & washed sharp sand for mortar and finished smooth to the rough surface of floor and punning including watering and curing with cost, conveyance, royalties of all materials with cost of all labour, and T&P required for the work etc. complete in all respect as directed by the Engineer in charge.SECOND FLOOR
121	Providing and laying of green certified carpet tiles thickness more than 5.5mm size 50X50 cm with nylon content of 100% Tufted Textured loop pile, manufacturer using latest dyeing technology. The backing has to be non pvc backing. Tufted Pile Weight Standard 14.8 oz. per sq. yd. with antistatic, thermal resistance , sound insulation & sound absorption properties. Carpet to have fire resistance of Cfl-s1 and suitable for allergies. The product has to be 100% recyclability with Environmental product declaration & material health statement certificate for sustainability. The product should have CRI green certified product. Rates including complete installation with backing foam, necessary stitching etc. The floor which receives the carpet to be thoroughly cleaned as per manufacturers specification. The carpet is to be laid over a bed of manufacturers approved adhesive spread evenly over the entire floor. The rate shall include cutting, trimming, fixing and clearing away of residual material to a location as directed. The rate shall also include supplying and laying of a protective layer in PVC or HDPE sheet of 500 microns thickness, held together with scotch tape. The laid carpet to be vacuumed after the removal of protective cover / on commissioning. If after the protective layer is removed and stains observed in the carpet because of inadequate protection, the same shall be shampooed and made good to the satisfaction of the project managers. FIRST FLOOR
122	Supplying and Laying MAKE IN INDIA broadloom carpet of having following specifications.. Made up from 100% Nylon 6 Cut Pile , Digitally injection Printed having Pile Height of 7.5 mm with Total Height of 9.5 mm . should have been Stitched 37 times / 10 cm with Pile Weight Not less than 1000 GSM and total weight of 2200 GSM. The Carpet should have a Primary Backing of PP Woven and Secondry Backing of PP Mesh with Gauge of 1/8 Cut Pile of Latex Natural Rubber. The carpet should be Color fastness to LightTest Method as per AATCC 16 standard ≥ 4.0 at 80 Hours . Also should have passed Static Electricity Test Method: AATCC 134 Less than 3.5 KV & Hexapod test Method: ASTM D 5252 ≥ 4. It should be confining to Anti Flammable,Anti Bacterial & Anti Microbial Test Method: ASTM E 648 ≥ 0.45 . The carpet to be supplied should be manufactured as per Green Pro, LCA EPD , CE Marking , NSF 140 standards and the manufaturing unit should be confining to UGBC , ISO 9001, ISO 14001 and ISO 45001 standards.The carpet to be laid as per the manufacture's specification and to be laid by its authorized agency or as Approved , with minimum 5 Years warranty from Manufacturer for any manufacturing defects . After laying carpet to be covered with transperent polythene to protect from dust,adhesive , colouring work at site The carpet shall be complete as per drawing & specifications of the EIC.SECOND FLOOR
123	Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Clerestory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately).Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.(Make-Green Land / Century/ Alstone)GROUND FLOOR
124	FIRST FLOOR
125	SECOND FLOOR
126	THIRD FLOOR
127	Dressed seasoned sal wood work framed and fixed in frames of doors & windows including cost,conveyance of all materials and cost of labour for fitting, fixing etc.complete as per the instruction of Engineer-in-Charge .GATEWAY
128	Supplying, fitting and fixing of 32mm thick flush door shutter with approved quality of 30mm thick BWR block board pasted with 1mm thick sunmica on both side of approved design and quality including cost of all door fittings and fixtures etc. complete in all respect as per the direction of the Engineer-in-Charge.GROUND FLOOR
129	FIRST FLOOR
130	SECOND FLOOR
131	THIRD FLOOR
132	GATEWAY
133	WOODEN FLOORING:- Providing and laying in position 10.5mm thick Bruce Engineered wood Flooring of approved shade of size 1820mm x 190mm having smart lock tongue and groove joints to secure long lasting joint. The material comprising of three layers, Top layer is of genuine hardwood surface, the middle layer is of pine or spurce ribs laid transversely and the third layer is stabilizing bottom layer. The floor is finished on top with three course of formaldehyde free oil or five course of UV curved formaldehyde free lacquer. The boards are installed on foam and plastic on top of the under floor and stuck to one another using adhesive in the groove of the board all complete including all accessories.SECOND FLOOR
134	Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinf. and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charg DSR VOL-I, SL NO-9.147 ,Page no-627. GROUND FLOOR
135	SECOND FLOOR
136	THIRD FLOOR
137	Providing and fixing fire resistant door frame of section 143 x 57 mm having built in rebate made out of 16 SWG G.I. sheet (zinc coating not less than 120 gm/sqm) duly filled with vermuculite based concrete mix, suitable for mounting 60 minutes fire rated door shutters. The frame is fitted with intumuscent fire seal strip of size 10x4 mm (minimum) alround the frame and fixing with dash fastener of approved size and make, including applying a coat of approved brand fire resistant primer etc. complete as per direction of Engineer-in-charge (Dash fastener to be paid for separately). FIRST FLOOR
138	SECOND FLOOR
139	THIRD FLOOR
140	Providing and fixing glazing in fire resistant door shutters, fixed panels & partitions etc., with G.I. beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than 120 gm/sqm) of size 20 x 33 mm screwed with M4 x 38 mm SS screws at distance 75 mm from the edges and 150 mm c/c , including applying a coat of approved fire resistant primer/powder coating of not less than 30 micron on G.I. beading, & special ceramic tape of 5 x 20 mm size etc complete in all respect as per NBC 2016, IS 16231 (Part 3):2016 and as per direction of Engineer-in-charge with glass of required thickness having 60 minutes of fire resistance both integrity & radiation control (EW60) and minimum 20 minutes of insulation (EI20). The manufacturer have to give test report/certification of fire glass and the glass should have the stamp showing the value of E, EW & EI. The glass shall be tested in approved NABL accredited lab or by any other accreditation body which operates in accordance with ISO/IEC 17011 and accredits labs as per ISO/IEC 17025 for testing and calibration scopes shall be eligible. The maximum glazing size shall not be more than 1100x2200 mm (w x h) or 2.42 sqm.FIRST FLOOR
141	SECOND FLOOR
142	THIRD FLOOR
143	Providing and fixing panic bar / latch (Double point) fitted with a single body, Trim Latch & Lock on back side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer- in- charge, all complete.FIRST FLOOR
144	SECOND FLOOR
145	THIRD FLOOR
146	Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge.FIRST FLOOR
147	Providing and fixing 50 mm thick glazed fire resistant door shutters of 60 minutes fire rating conformingtoIS:3614(Part-II), tested and certified as per laboratory approved by Engineer-in- charge, with suitable mounting on door frame, consisting of vertical styles, lock rail, top rail 100 mm wide, bottom rail 200 mm wide, made out of 16 SWG G.I.sheet (zinc coating not less than 120 gm/sqm) duly filled FR insulation material and fixing with necessary stainless steel ball bearing hinges of approved make, including applying a coat of approved fire resistant primer etc. all complete as per direction of Engineer-in-charge (panneling to be paid for separately). FIRST FLOOR
148	SECOND FLOOR
149	THIRD FLOOR
150	Providing, assembling and supplying vision glass panels (IGUs) comprising of hermeticallysealed 6-12-6 mm insulated glass vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor. (i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face #2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement.GROUND FLOOR
151	FIRST FLOOR
152	SECOND FLOOR
153	THIRD FLOOR
154	Fixed Glass:- Providing and fixing 12 mm thick frame less toughened glass partition Dorma premium (911298) PT 80 Glass to glass connector with silicone, 12mm clear toughened glass with cutout and hole,including perimeter sealing of glass to glass joints with silicon sealant,etc, as per drawing and specification including the cost of all materials,T&P,etc all complete as per the direction of Engineer-in-charge.GROUND FLOOR
155	FIRST FLOOR
156	THIRD FLOOR
157	Ventilator Casement window single panel with or without fixed panel with S.S. 304 friction hinges as per size and weight of sash, single point locking zinc alloy (zamak) powder coated handles.DSR VOL-I, SL NO-9.147.D1 ,Page no-660. Using R1series with frame (33mm & above) x (35mm & above) & sash/ mullion (33mm & above) x (50 mm & above). (Height upto 0.90 metre).GROUND FLOOR
158	FIRST FLOOR
159	SECOND FLOOR
160	THIRD FLOOR
161	TEXTURE PAINT:- Providing and applying two coats unitile's Royal/Rivera make in approved shade on a smooth cement sand plaster. The composition of the texture paint should consist of Acrylic Copolymer Resigns combined with Quartz, Silica,mineral aggregates, synthetic inorganic pigments, bactericide, fungicides and various other additives,giving the product water repellant properties. The first coat to be applied by brush or wool roller as a base coat, diluted with sufficient water and the final coat applied undiluted with trowel and then finished with acrylic trowel to obtain the specified grooves.The thickness of both coats dhould be 1.0 to 1.5 mm. The water repellency of the product is 86gm/m2 as per test method IS: 5410-1969. GROUND FLOOR
162	FIRST FLOOR
163	SECOND FLOR
164	THIRD FLOOR
165	STRUCTURAL GLAZING SUB FRAME:- Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. ( The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account). The weight of aluminium extruded section shall be taken for purpose of payment.GROUND FLOOR
166	FIRST FLOOR
167	SECOND FLOR
168	THIRD FLOOR
169	MS STEEL STRUCTURE- Supplying, Providing, Fabricating, Assembling, hoisting, erecting and placing in position MS Built-up section/ Tubular Structure (MS) confirming to IS 2062 Grade Yst 250-350, Tubular Structure:- made from steel hollow sections, ISI marked from SAIL/ RINL/ TATA/ JINDAL, confirming to IS 1161/4923, Grade Yst 310, thickness upto 10mm) in the profile shape as per drawings with special plate connector, pinion joints, Plates, hollow sections, etc and applying a coat of epoxy primer, and including Preparation of detailed fabrication and erection drawings of Structural steel work from design drawings issued by Engineer- in- charge and incorporation of Engineer-in-Charge’s comments on same, transportation from fabrication yard, cutting, threading, machining, leads and lifts upto all heights, tools and plants and necessary scaffolding etc. required for all operations involved to make structure of Metal sheet roofing .The tubular structure system with plate connectors, pinion joints, etc must be sustained up to 280 km/hour wind pressure. The structure has to be provided as per conceptual drawings of metal shade.TERRACE FLOOR
170	GATEWAY
171	POLYCARBONATE SHEET ROOFING:- Supplying, providing & fixing of multi walled polycarbonate sheet cover of 12 mm thick of required color at the top of the structure of required diameter and height. The jointing at the junction of sheet to be done with powder coated aluminium joint profile having necessary accessories like sealing strip, end cap, stopper, fastener, joiner, screws etc of required thickness. The aluminium profile to be fixed using self drilling SS screws & the profile edges to be sealed using weather silicon. Rate includes Transport to the site and installation with all accessories, screws etc complete as per the design approved by the Engineer-in-Charge.TERRACE FLOOR
172	Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including:(a) Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)-cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including:(b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3 Dimentional movement for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry/ structural steel framework of building structure using stainless steel anchor fasteners/ bolts, nylon seperator to prevent bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers.GROUND FLOOR
173	FIRST FLOOR
174	SECOND FLOOR
175	THIRD FLOOR
176	GLASS :- Providing, assembling and supplying vision glass panels (IGUs) comprising of hermeticallysealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor. GROUND FLOOR
177	FIRST FLOOR
178	SECOND FLOR
179	THIRD FLOOR
180	Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer- in-Charge.GROUND FLOOR
181	FIRST FLOOR
182	SECOND FLOR
183	THIRD FLOOR
184	Providing, fabricating and supplying shadow box of required size and shape, for fixing in the spandrel portion of the structural glazing, in linear as well as curvilinear portions of the building by providing semi -rigid, inorganic, non-combustible fibre glass wool insulation 50 mm thick, conforming to IS: 8183 and BS: 3958 Part 5. The insulation layer shall have facing (factory bonded on surface # 1 of the fibre glass insulation layer), of black non-woven fibre glass tissue of nominal thickness 0.5 mm and nominal mass not less than 60 gm /sqm, made of randomly oriented glass fibres distributed in a binder by a wet-lay process including fixing 1.5 mm thick solid aluminum sheet backing using, 6 mm thick cement board including SS rivets, nuts, bolts, washers etc complete.GROUND FLOOR
185	FIRST FLOOR
186	SECOND FLOOR
187	THIRD FLOOR
188	SPANDREL GLASS PANELS :- Providing and supplying Spandrel Glass Panels comprising of 6 mm thick heat strengthened monolithic float glass of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade so as to match the colour and shade of the IGUs in the vision panels etc. ,all complete for the required performances as specified, as per the Architectural drawings, as per the approved shop drawings, as specified, and as directed by the Engineerin- Charge. For payment, only the actual area of glass on face # 1 of the glass panels (but excluding the area of grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm. (Payment for fixing of Spandrel Glass Panels in the curtain glazing is included in cost of relevent Item*).“(i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 K etc. . The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement.GROUND FLOOR
189	FIRST FLOOR
190	SECOND FLOOR
191	THIRD FLOOR
192	GLASS RAILLING IN CUTOUT -: Providing and fixing of glass railing using 10 mm Clear toughened glass and 40x40mm balustrades ( Grade 304 ) with point fixtures to hold the glass. The balustrades positions are derived at 1200 from c/c with glass height taken as 950 mm . The entire balustarde will be of height of 1200mm from smapul ply fixing point and 50 mm dia stainless steel (Grade-304) pipe use in top site. The rate include cost of all material, labour,conveyance etc for site.SECOND FLOOR
193	THIRD FLOOR
194	GFRC Cornice :- Supplying, Providing and Installation of GFRC CORNICE/ MOULDING (Glass Fiber Reinforced Concrete), Make “TRIVENI, SAMUDYAM”, with where fixing to be done Pattern, design, and colour of approved make to be fixed on/between RCC /Block work Column or structural work with Dry Fixing method with appropriate MS Structural & Cleats frame work, using fasteners, and necessary hardware etc. The element shall be made from '53 grade' Portland Cement make Birla/ 'JK Cement' or equivalent, Quartz, Fine Silica Sand, Alkali Resistant Glass fibre make 'Owens Corning' or equivalent, Super plasticizers / Additives make by 'BASF' or equivalent, Polymers make 'BASF' or equivalent and U.V resistant Synthetic inorganic pigments shall be used for pigmentation make 'BAYFERROX (Germany)' or equivalent. The material casting shall take place in Synthetic Rubber / FRP Mould manufactured by Mould / Tool / Mould Grade Resin of Revex/ 'Reckli' or equivalent.GROUND FLOOR
195	MCM CLADDING :- Supply of MCM Modified Clay Material ‐ MCM Slate Sunnye ‐ 1200 x 600 mm , thickness 2.5mm to 3mm PHOMI make, as per company standard dimension, pattern, colour as specified, manufactured through unfired patented (Ref: US patent 8505840 B2 & European Patent 2157139) manufacturing technology, bonded together by using low heat temperature and having CE approval with the thermal conductivity of 0.0590 W/M.K — EN 12667 (2001), thermal resistance of 0.0568 M2 K/W— EN 12667 (2001) and Fire Insulation ‐ Class A— ASTM E84‐ 15. The product should be patented from United States and Europe and with certifications by IGBC, Singapore Green Label and China Green Building material. MCM Materials should be fixed with suitable Cement/ Polymer/Epoxy based adhesive as per adhesive chart and substrate and per directions of Engineer in-charge. Grouting should be done using filling and pointing method as per installation drawing provided, and colour of the grout should be as per the architect’s specification depending on the substrate and as per the direction of Engineer in-charge.GROUND FLOOR
196	GATEWAY
197	TOILET WATER PROOFING:- Surface Preparation Cleaning all concrete surfaces free of laitance, dust, dirt, cavities, projecting nibs etc.by grinder and wire brush. Grease should be cleaned using a chemical degreaser and washed with clean water and allowed to dry. Remove all protrusions from concrete surfaces using a fine hair broom finish. Remove moss and lichen manually and treat the surface with a fungicide. Wash the surface thoroughly with clean water and allow it to dry. Standing water must be removed to prevent subsequent compromise of waterproof properties. Surface should be absolutely dry before application of Water proffing. The surface should be grinded to remove contaminants, laitance and weak concrete, so as to have a sound concrete surface with adequate profile, including cost of all material, Labour, T&P etc all complete as per direction of Engineer In Charge. GROUND FLOOR
198	FIRST FLOOR
199	SECOND FLOOR
200	THIRD FLOOR
201	TERRACE FLOOR
202	Nozzle Grouting at Construction Joints:Nozzle grouting to be done with cement slurry admixed with expanding grout admixture Cebex 100. Cebex 100 to be mixed @225 gm per bag of cement after ponding test for 72 hours. GROUND FLOOR
203	FIRST FLOOR
204	SECOND FLOOR
205	THIRD FLOOR
206	Expansion joint Treatment- Supplying and fixing of elastomeric membrance of 200mm x 2mm size for expansion joint sealing from approved manuefacturer, fixing with epoxy adhesive of approved quality complete. GROUND FLOOR
207	Supply and apply 1 mm thick aluminium plate of required width for protection of TPE membrane as per manufacturrar’s specification and satisfaction of EIC. (200 mm width) GROUND FLOOR
208	Sealing the cracks cutting V groove of 12mm x 15mm and sealing the same with cement : sand 1:4 admix with Rearm Bond SBR45 @ 10% of the cement weight. Then fixing of nozzles along the cracks and all other areas. Injection of cement slurry admix with Armgrout Additive @ 250gm per bag of cement and Tufcrete - @ 10% of the cement weight.TERRACE FLOOR
209	Sealing the cracks cutting V groove of 12mm x 15mm and sealing the same with rearm bond Uw - epoxy sealant. Then fixing of 12mm dia NRV packer along the cracks and other are leakage area and injecting Arm Grout EPLV- low viscous epoxy grout till the refusal of grout pump.TERRACE FLOOR
210	Bore Packing (4\\"-8\\") Providing necessary formwork for packing the bore using suitable arrangement (depending upon site conditions). Applying a coat of styrene- butadiene based polymer coating using Latex. Packing the gap using non-shrink cement polymer based grout up to the surface of the bore whilst the Latex is in tacky state seal the Bore with polyurethane Sealant, ,including cost of all material, Labour, T&P etc all complete as per the direction of Engineer in charge.TERRACE FLOOR
211	Polyurethene(PU) Coating of 1.5mm thick Provindin & applying the surface with primer & Providing two coats of liquid applied, solvent-free elastomeric water proofing membrane, shall be made of hydrocarbon free polyurethane with at least 85% solid content Nitoproof 600PF with necessary surface preparation, coving, primer etc. The waterproofing membrane shall be terminated on the top of parapet walls. including cost of all material, Labour, T&P etc all complete as per the direction of Engineer in charge.TERRACE FLOOR
212	PUF Spary Insulation SystemProviding and applying 50 mm thick two component,HFC blown, free from CFC/HCFC polyurethane based sprayable rigid foam system closed-cell type, designed to meet insulation requirements in roof applications.Standard Compliance: IS 12432-3 (2002): Application of Spray Applied Insulation - Code of Practice, Part 3: Polyurethane/Polyisocyanurate [CHD27: Thermal Insulation]Type-1 foam as per Table-1 of ASTM D 7425TERRACE FLOOR
213	Geo Fabric MembraneProviding and laying Geo fabric Membrane 150 Gsm, non woven, 100% polyester of thickness 1 to 1.25 mm to act as separation layer before screed concrete including cost of all material, Labour, T&P etc all complete as per the direction of Engineer in charge. TERRACE FLOOR
214	Grading Concrete (1:1:2) mm thick Providing and applying protective Grading concrete of avg 50 mm thickness above Geo fabric membrane The concrete shall be admixed with intergal based water proofing and finishing surface suitably, curing, cleaning, testing etc. The concrete shall be cut with paneel the 2m x 2m up to depth 1/3 th of depth and the groove shall be filled with Polyurethene sealant including cost of all material, Labour, T&P etc all complete as per the direction of Engineer in charge. TERRACE FLOOR
215	INTERIOR WORKSProviding & Fixing of Fibre Glass Acoustical Suspended Ceiling (600MMX600MM) 90 Edge Tiles with 15mm face exposed grid. The tiles shall have smooth laminated visual with Humidity Resistance (RH) of 95%, NRC 0.85 – 0.95(Average value of Absorption Co-efficient readings taken at as per ASTM C423 standard, , Light Reflectance ≥88% as per ASTM E-1477, Colour Pebble White, Fire Performance of Class 0/1 as per BS 476 Part 6/7 with 20/25mm Square Tegular/Microlook 90˚ edge and 8mm drop in module size of 600 x 600mm. It shall be suitable for Green Building application, with Recycled content of 85%.SECOND FLOOR
216	Providing and fixing False ceiling as per Saint Gobain Specifications made of standard G.I. Sections and 12mm thick gyp board sheets inclusive of all hangers, edge members and other clips complete, with sheets fixed with proper Philip fastner by power drills and joints duly finished ensuring level in line, complete with putty, primer and painting of approved make and colour. Cost includes cutouts for electrical fittings, materials, labour, T&P etc complete as per direction of the Engineer-in-charge.(GROUND, FIRST, SECOND, THIRD FLOOR)
217	PARTITION WALL: Supplying and fixing of double skin wall paneling made of aluminum anodised section framing conforming to standard Aluminium sections as horizontal and vertical members with atleast 600mm c/c with 9mm thick BWR block ply and 4mm thick veneer finished with melamine polished on both the face complete .(FIRST, SECOND, THIRD FLOOR)
218	GLASS PANELS: 5.0 mm thick glass panels (weight not less than 12.50 kg/sqm). ( DAR-2023 Vol-1 (pg-454 ) SL NO-9.7.7.2 (FIRST, SECOND, THIRD FLOOR)
219	WALL PANELLING WITH VEENER.: Supplying and fixing of wall paneling made of aluminum anodised section framing conforming to standard Aluminium sections as horizontal and vertical members with atleast 600mm c/c and fixing of 9mm thick BWR ply with 4mm thick veneer pasting finished with melamine polishing complete .(FIRST, SECOND FLOOR)
220	SLATS IN WALL PANELLING: Supply & installation of Slats in wall panelling are made of pinewood E1 grade fiberboard, Melamine laminated finish, groove perforated slats L16-3/L23-3/L32-3/Customized - (3mm grooves Slats @16mm centres) back lined with black acoustical fleece, tongue-groove edge for a seamless look, of size 192 & 128x2440x15/17mm thick having base density 700Kg – 800 Kg/m3, weight 12Kgs/m2 installed by using GI strut system. The GI strut system includes GI Cross channel having thickness 0.45mm, length 3600mm, knurled web 40mm, depth 10mm and equal flanges 15mm is fastened vertically/horizontally at every 600mm centres. Aluminium core cross channel (CC18) having thickness 0.5mm, length 2400mm, web 15mm & 27mm, depth 18mm and flanges of 7mm with suitable edge & centre brackets is then fixed perpendicular to the CC25with the help of fasteners at every 400mm centres. Slats of size 192 & 128x 2430x15/17mm in then fixed perpendicular to CC18 with suitable edge & centre brackets. Contractor to provide expansion joints of 3mm at every 5mtrs both ways. Panels shall be back lined with acoustical infill of 1000gsm x 50mm thick adhered to the wall using Stick adhesive Technical Parameters.(Make - Aeroceil, Duxyon, Armstrong)(FIRST, SECOND FLOOR)
221	STRETH WALL FABRIC ACOUSTIC PANEL : Supply and installation of Stretch wall fabric system by using FR Grade acoustic fabric of size 1700mm width, shall be stretched by using wooden base 12.5 mm thick, rigid vinyl Stretch Tracks half wrap/full wrap 12.5mm and Midseam 12.5mm, Strand wood wool board , Infills polyester fibre infill with requisite accessories & tools. Wooden base 12mm is first installed on the wood fibre along the marking lines with metal fasteners inserted at 300mm centres. 12.5 mm tracks to be installed on wooden base, after applying Stick adhesive on both surfaces for a true and continuous secure grip, and heavy-duty fasteners at 150mm centers on one/both sides of Stretch Tracks. The GI strut system includes GI Cross channel having thickness 0.45mm, length 3600mm, knur led web 40mm, depth 25mm and equal flanges 15mm is fastened vertically/horizontally at every 600mm centres. Strand Wood Wool Board is square edge magnesite bonded pinewood fibre panels of size 600x1200x25mm having density 400kg/m3, weight 4kg which is fixed to Cross Channel 25mm. Long edge of panels should be perpendicular to length of Cross Channel , Infills polyester fibre infill 1000gsm 25mm thick adhered on Strand Wood Wool Board panel by using adhesive. Fabric of width 1700mm is then aligned to the Stretch tracks by following the fabric thread line or pattern. The fabric is stretched and tucked into the Stretch tracks and secure into the locking jaws so that it will be smooth, free of wrinkles with the tucking tools. Note -minimum 50mm additional fabric is required for tucking hence maximum module wall fabric width would be 1600mm. Technical Parameters: • Core – Pine wood fibre & Poly fibre • Fire – Class A • Acoustics – NRC 0.90 • Climate (OC RH) – 55, 90 • Termite resistance – Yes • Light reflectance – Colour dependent • Green (RC %) – Low, 10 inatallation as per direction of EIC.(Make-Armstrong/Hunter Douglus/Anutone/ Aeroceil)
222	DRY WALL PARTITION (MAGNESIUM BOARD): Supply and Installation of 70 mm thick magnesium oxide board drywall Tufbloc partition system having which includes two layers of tufbloc magnesia square board having square edge & size 2400 X 1200 x 10 mm to be fixed on the either side of the GI stud channel framework in horizontal position of length side board. Now the frame work includes Floor / Head channels having thickness 0.06 mm length 3600 mm ,equal flanges of 32 mm & web of 50 mm fixed to floor & ceiling with suitable fasteners at 300 mm centers staggered noise & fire rated silicon sealant tocaulked along the perimeter of the partition frame before fixing channels.Then stud channels SC 48 having thickness 0.75 length 3600 mm , un equal flanges of 36 mm & web of 48 mm should be placed into the floor / head channels positioned vertically at 600 mm centers. Horizontal intermediate channel at 1200 mm centers to locked with the vertical studs. Extra reinforcement to be provided at openings. Apply Synthetic poly fiber 10 x 25 is 50 mm width,600/1200 mm density 500 gsm filled between the studs & held in position by using chicken mesh wire / pasting on the board Manufacture By Sgaapl. Now, boarding is to done on each side of studs framework in a staggered pattern by the help of self drilling screw at 300 mm centers. After boarding of two boards jointing & finishing is to be done by joint compound.(Make - Aeroceil, Duxyon, Armstrong)(FIRST, SECOND, THIRD FLOOR)
223	MCM CLADDING: Supply of MCM Modified Clay Material ‐ MCM Slate Sunnye ‐ 1200 x 600 mm , thickness 2.5mm to 3mm PHOMI make, as per company standard dimension, pattern, colour as specified, manufactured through unfired patented (Ref: US patent 8505840 B2 & European Patent 2157139) manufacturing technology, bonded together by using low heat temperature and having CE approval with the thermal conductivity of 0.0590 W/M.K — EN 12667 (2001), thermal resistance of 0.0568 M2 K/W— EN 12667 (2001) and Fire Insulation ‐ Class A— ASTM E84‐ 15. The product should be patented from United States and Europe and with certifications by IGBC, Singapore Green Label and China Green Building material. MCM Materials should be fixed with suitable Cement/ Polymer/Epoxy based adhesive as per adhesive chart and substrate and per directions of Engineer in-charge. Grouting should be done using filling and pointing method as per installation drawing provided, and colour of the grout should be as per the architect’s specification depending on the substrate and as per the direction of Engineer in-charge . (GROUND, FIRST)
224	GRC JALI Providing and fixing Glass Reinforced Concrete (GR.C) Screens in approved size pattern, design, shadeand thickness of 50mm on frame and design element in 30mm thick have weight approximately between 3.5 4 Kg per Sq Ft and color of M/S UniStone make or equivalent. The above weight and thickness is considering dimensions of screens up to 2133mm in height and 1219mm in width and having at least 50% void space. The screens should be made from '53 grade' White Portland Cement manufactured by JK Cement' or equivalent, Quartz, Fine Silica Sand, Alkali Resistant Glass Fiber manufactured by 'N.E.G JAPAN or equivalent, Super Plasticizers manufactured by \\"BASF or equivalent Polymers manufactured by 'BASF or equivalent and UV resistant Synthetic inorganic pigments should be used for pigmentation manufactured by 'BAYFERROX (Germany) or equivalent. The material casting should take place in FRP Molds. The fixing of Screens should be 'Dry fixing' Le to be done with M.S Galvanized Clamps, fixtures and fasteners of Hilti / Fischer.(GROUND FLOOR)
225	Roller Blind: Supplying and fixing of Roller blinds by fixing powder coated top channel, bottom channel with bottom end cap, control unit and good quality of 0.6 mm thick fabric of approved desgin and quality etc. complete.
226	WALLPAPER; Supply and Installation of Wallpaper of reputed brand such as of design/shade 7957-1. Rate includes complete installation including the cost of all materials, cost of all labour, conveyance, loading & unloading, and T&P, etc. complete in all respect as per direction of the Engineer in Charge.
227	Louvers Wall Panelling: Supply and fixing of 5-14mm calcium Polymer based vertica systems of LEBEN/NEWTECH/ALWOOD Innovations of panel size of 1230mmx2800mm along with option to custom size to a maximum of 3000mm in length in approved shade,manufactured in india, made with high temprature thermal transfer technology, waterproof,fire retardant and anti-bacterial. Termite resistant, rust proof material. For wall panels to be installed with aluminum/GI clip of suitable gauge & size, subject to change according to site conditions. For walls, it can be directly Screwed/ adessive to the wall. Panels to be installed using suitable, J-Trim/J-Trim/L - Trim using same shade for edge profiles. Panels are maintenance free and with 10years warranty for colour & finish of the panels. All material, accessories as per direction of the Engineer in Charge.
228	FURNITURE WORKS FORUM MBG FXD ARMS TELLER BASE Powdercoated Teller Base-Forum Medium Back Mesh Chair-AN 70 Mesh -Centre Titi Mechansim -Powdercoated Teller Base -Fixed Arms-Nylon Base -Fabric Upholstered Cushion SeatGROUND FLOOR
229	Supplying and placing a three seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. The thickness of the wood should allow for the heavy tension webbing. The sofa shall have spring attached and also be padded separately. The frame shall be padded with high resilience polyurethane foam having density 45Kg/m³ in seat and 32Kg/m³ in back. The backrest of the sofa shall be supplied with traditional tufted buttons with decorative appealing. There shall be cushion arm provided padded with high resilience polyurethane foam having density 32Kg/m³. The complete structure shall be upholstered with leatherite tapestry 0.8±0.1 mm thick and 535 GSM. The understructure shall consist of SS 304 grade leg with shiny chrome finish having thickness 12mm. There shall be buffers provided at the bottom to avoid scratches on the floor as well as uneven surfacing. The seat size shall be 2000±10 mm(W) X 620±10 mm (D) X 430±10 mm (H). Overall width = 2600±10 mm, overall depth = 1000±10 mm & overall height = 740±10 mm. Make- Godrej/featherlite/Geeken/wipro or equivalent
230	Providing and supplying single seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. The thickness of the wood should allow for the heavy tension webbing. The sofa shall have spring attached and also be padded separately. The frame shall be padded with high resilience polyurethane foam having density 45Kg/m³ in seat and 32Kg/m³ in back. The backrest of the sofa shall be supplied with traditional tufted buttons with decorative appealing. There shall be cushion arm provided padded with high resilience polyurethane foam having density 32Kg/m³. The complete structure shall be upholstered with leatherite tapestry 0.8±0.1 mm thick and 535 GSM. The understructure shall have SS 202 grade with shiny chrome finish frame having thickness 12mm. There shall be buffers provided at the bottom to avoid scratches on the floor as well as uneven surfacing. The seat size shall be 670±10 mm(W) X 620±10 mm (D) X 430±10 mm (H). Overall width = 1270±10 mm, overall depth = 1000±10 mm & overall height = 740±10 mm. Make- Godrej/featherlite/Geeken/wipro or equivalent
231	Providing and supplying centre table with an overall size 900mm X 900mm X 410mm. The top should be made up of 75mm thick, it would be 25mm at mid and 75mm at sides. The MDF top should have decorative finish with approved veneer and PU polish accordingly. The understructure shall consist of 4 nos. of MS sheet gold leg with 6mm thick. Make- Godrej/featherlite/Geeken
232	VERVE GLASS TABLES (610-FS-DM SIDE TABLE) Square Chrome Frame with Glass Top Size : 600 X 600mm x 505ht ,Make- Godrej/featherlite/Geeken
233	THREE SETAER WAITING CHAIR BRUNEY LEATHERETE - 3 SEATERBruney Three Seater Cushioned Tandem (Leatherette)Fixed ArmsSize : L 1980 x D 690 x H 825 mm Make- Godrej/featherlite/Geeken
234	VERVE GLASS TABLES (610-FL-DM CENTER TABLE) Rectangular Chrome Frame with Glass Top Size -1200 x 600mm . Make- Featherlite, SIT or equivalent.
235	Providing and supplying high back chair with ergonomic design, comfortable & aesthetically appealing. The seat shall be made of 18mm thick hot pressed commercial plywood upholstered with high resilience moulded polyurethane foam 50mm thick having density 40kg/m³ with foam net tapestry 0.9mm thick and 300 GSM and the back shall be made of injection moulded polypropylene net cover upholstered with breathable mesh tapestry. The backrest of the chair shall be made by keeping the natural curvature of the spine with adjustable lumbar support. The chair shall be supplied with injection moulded PU adjustable arm completely joint with seat. For seating durability the chair shall have ACTICE BIO-SYNCHRO mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The Pedestal should have five legged made of die cast aluminium having pitch circle dia.. 700 mm fitted with 5 nos. twin wheel castors. The castors of the chair should beinjection moulded in 30% glass filled nylon, confirming to ANSI/BIFMA standards X5.1-2011 tested to perform 98,000 cycles with 250lbs load. The seat size shall be 520±10 mm(W) X 500±10 mm(D) and back size shall be 495±10 mm(W) X 750±10(H) from seat & overall height = 1150±10 mm. Make- ISIT,Godrej/featherlite/Geeken
236	Providing and supplying mid back chair with ergonomic design, comfortable & aesthetically appealing. The seat shall be made of 18mm thick hot pressed commercial plywood upholstered with high resilience moulded polyurethane foam 50mm thick having density 40kg/m³ with foam net tapestry 0.9mm thick and 300 GSM and the back shall be made of injection moulded polypropylene net cover upholstered with breathable mesh tapestry. The backrest of the chair shall be made by keeping the natural curvature of the spine with adjustable lumbar support. The chair shall be supplied with injection moulded PU adjustable arm completely joint with seat. For seating durability the chair shall have ACTICE BIO-SYNCHRO mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The Pedestal should have five legged made of die cast aluminium having pitch circle dia.. 700 mm fitted with 5 nos. twin wheel castors. The castors of the chair should beinjection moulded in 30% glass filled nylon, confirming to ANSI/BIFMA standards X5.1-2011 tested to perform 98,000 cycles with 250lbs load. The seat size shall be 520±10 mm(W) X 500±10 mm(D) and back size shall be 495±10 mm(W) X 750±10(H) from seat & overall height = 1050±10 mm. Make- Godrej/featherlite/Geeken
237	DISCUSSION TABLE VDT -1050: Table Top - 25mm Thick Pre-Laminated Particle Board finished with 2mm PVC Edge Banding. Supports - Supported on 25mm thick Pre - laminated Particle Board Gable ends Wire Management - 85mm dia Laptop socket & Aluminium pole for wire management is considered.Make- Godrej/ featherlite/ Geeken
238	Alpha Medium PP (Black)Back Mesh ChairAN 70 MeshFabric Upholstered Cushion SeatFixed ArmsPowdercoated 4 Legs, Make- Godrej / featherlite / Geeken
239	Providing and supplying a high back chair with ergonomic design, comfortable & aesthetically appealing. The seat and back shall be made of 18mm thick hot pressed BWP plywood padded with high resilience polyurethane foam 50mm thick having density 40kg/m³ in seat and 40mm thick having density 32kg/m³ in back. The same shall be upholstered with leatherite tapestry 0.8mm thick and 535 GSM. The backrest shall be made by keeping the natural curvature of the spine which helps to provide lumbar support. The chair shall be supplied with PP arm with cushion having leatherite covering top pivot joint with back. For seating durability the chair shall have knee tilt 360 degree revolving mechanism having four position locking and tilt tension adjustment with anti-shock feature which provides back strength for the chair. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 65mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The Pedestal should have five legged Polypropylene base with chrome having pitch circle dia. 700 mm fitted with 5 nos. twin wheel castors. The castors of the chair should be injection moulded in black 30% glass filled nylon, confirming to ANSI/BIFMA standards X5.1-2011 tested to perform 98,000 cycles with 250lbs load. The seat size shall be 510±10 mm(D) X 570±10 mm(W) and back size shall be 550±10 mm(W) X 670±10 mm(H) from seat. Overall height shall be = 1130±10 mm, overall depth = 690±10 mm & overall width = 700±10 mm. Make- Godrej/featherlite/Geeken
240	Executive Chair for Court Dias.(Wooden) Make-Godrej/featherlite/Geeken
241	Cupboard 13'6\\"Lx1'6\\"Wx2'6\\"HT,Providing & Fixing of Cupboard of size 13'0\\"Lx1'6\\"Wx2'6\\"HT, made of 19 mm thick BWR Ply sandwiched together and back to be supported with single 19 mm BWR ply. All exposed surface to be laminated with 1mm thick decorative laminates (Textured). Four Shelve of size 3'0\\"(L) x2'(W) x 10\\"(D) should be provided made of 19mm thick prelam BWP ply with G Profile, Auto Hinges,Corner joint and 5 mm plain glass etc, including all cost of materials, T&P, all labour etc complete as per the Direction of Engineer in - charge. Make- Godrej/ featherlite/ Geeken
242	Providing and supplying 4 Seater Dining Table (with chairs) made up of Teak Wood having ONYX marble Top with Melamine Finish: The understructure is made of teak wood and consists of a melamine finish. The table top carrying maximum capacity of 56000 Grams weight. Item dimensions (L x W x H) 149.9 x 89.9 x 254 Centimeters. Make- Godrej/ featherlite/ Geeken
243	L-SHAPE WORKSTATION SIZE: 1500/1500W X 600/600D X 750HT TABLE TOP WITH 1200MM HT PARTITIONSpecifications:Table top: Made of 25mm thick prelaminated particle board of approved shade. All the edges of workstation surface shall be provided with machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC.Partition: Height - 1200mm frame with top and sides in Aluminium trims and junctions with diecast caps. Partition is made of 50mm thick 1200mm ht NEO based system with fabric above and lamiante below the table top.Fabric magnetic and glass markers are provided for each workstation.Under Structure Support: 18mm thick PLT gable end.Wire Management: Raceways are provided BTT only main spine and skirting on main/return (inside) spine for power and data cable management. 65mm dia grommet hole is provided for wire access, With pedestal. Make- Godrej/ featherlite/ Geeken
244	FORUM VA PC 4 LEGS FXD ARMSWD -SMALLForum Low Mesh Back Visitor ChairAN 70 Mesh Fixed ArmsWriting Desk - SmallPowdercoated Four Legs Fabric Upholstered Cushion Seat Make- Godrej/ featherlite/Geeken
245	VENUS AUDITORIUM CHAIRMetal frame for seat & back.3 mm Foam laminated fabric.Moulded PU foam of 45 density +/- 5 density tolerance.Wooden Polished armrest without cupholder.Tubular \\" C \\" Channel Pedestal.PPCP tray for seat & back.Seat numbering for seat & back both.Row numbering.Black powder coating surface.Auto tip up & sliding feature. Make- Godrej/ featherlite/ Geeken
246	Executive table L Shaped 8'0\\"Lx3'0\\"Wx2'6\\"HT, 6'0\\"Lx3'0\\"Wx2'0\\"HTProviding & Fixing of study table of size 8'0\\"Lx3'0\\"Wx2'6\\"HT, 6'0\\"Lx3'0\\"Wx2'0\\"HT TOP and sides of table to be made of two 19 mm thick BWP Ply sandwiched together and back to be supported with single 19 mm BWP ply. All exposed surface to be laminated with 1mm thick decorative laminates (Textured). Five drawer of size 2'0\\"(L) x2'(W) x 69\\"(D) should be provided made of 19mm thick prelam BWP ply with decorative laminate, soft close channels, concealed handle etc, including all cost of materials, T&P, all labour etc complete as per the Direction of Engineer in - charge. Make- IGodrej/featherlite/Geeken
247	E.I. WORKEXTRA LIGHT FIXTURES FOR CONFERENCE HALL SITC of extruded black powder coated Aluminium housing 2W/ mtr step light with provision for LED strip with diffuser, provision for illuminated seat numbering on both sides, rubber grip, vertical screwing ,12/24V in complete as per direction Eng-in-charge.Make-Belight/Illumax/Equivalent
248	Supply Installation testing and Commitionning of Almunium Made decorative picture light with bronze Finish having dimension of 355x180x95 mm with 7 W and Delivering 270 Lumen with Flexible neck for adjusting beam CRI>80 having cat ref -31402 MUZIRIS 7W With all accessories.(Make:Panasonic/LT/Havells /Philips/Wipro /Crompton/Bajaj)The luminaire should be Replacement Warranty will be 2 years
249	Supply, Installation Testing and Commissioning of IP20 LED strip with a nominal system lumen output of 1600 lm /m with system efficacy of 102lm/W SDCM<=3 The luminaire shall have a rated system lifetime of 30,000 hours. The luminaire shall have a color temperature of 4000K and CRI>80with No of LED 120 Nos . luminaire is to operate on 24VDC.with working temperature rage of upto 35degC ambient. Luminaire must be supplied along with all the accessories such as driver, moutning tracks/ clips, end caps, diffuser, strip connectors etc as applicable. Similar to PhilipsFlexCove G5 LS170S G2 Basic (5m Roll) + Accesories With all accessories.(Make:Panasonic/ LT/ Havells / Philips/ Wipro / Crompton/ Bajaj) The luminaire should be Replacement Warranty will be 2 years
250	S/I/T&Commissioning of UPS Incoming Panel made out by 2mm CRCA steel sheet duly derusted & painted by simens grey powder cote paint is designed as G.A drawing. as per direction of Engg.-in-Charge. Warrentee period of replacement of panel & accessories must be 1 year & compelete test certificate must be submitted along with panel board including component list.Type 2 SPD,40kA shall be installed in the incomer. 20x10mm Separate Aluminium Earth bus bar should be installed.In commer- 01 no 125A 4P MCCB 25KA withTMR based release with adjustable overload ,Icu=100%Ics, on/off trip indication.( Make-LEGRAND-DPX3 / Siemens-3VA Model/ Schneider- CVS/ABB Formula
251	LIGHTNING PROTECTION SYSTEM & UPS-Supply of 8 mm Aluminum Round Conductor.Tested as per IEC 62561. as per direction of engineer in charge.Make-OBO/Dehn/ABB
252	Supply of Roof conductor holder for parapet- Polyamide Conductor holder:With M8 female thread or diameter 7mm, M8 Screw to connect the conductor holder.Weather and temperature resistant from -35 to +90 degree Celsius tested. Conductor holder @ 1 meter distance.Tested as per IEC 62561. as per direction of engineer in charge.Make-OBO/Dehn/ABB
253	Supply of Polyamide roof cable holder for flat roof:DIN 48829 Form B1. Closed form with bottom. Filling weight 1Kg (frost-resistant concrete). Sleeve from polyethylene, black @ 1 meter distance. Tested as per IEC 62561. Make-OBO/Dehn/ABB
254	Supply of Connector: For T cross and parallel connectors. Quick installation using hexagonal bolt M10X30 high-grade hot dip galvanised. Tested as per IEC 62561.2nos/expansion piece Make OBO/Dehn/ABB
255	Supply of 1 mtr vertical air terminal with mounting accessories on the flat surface to meet the requirements of IS/IEC 62305. Tested for Electrical , mechanical and chemical as per IEC 62561. Tested for 100kA lightning current. MakeOBO/Dehn/ABB
256	Supply of Vertical air terminal with accessories:Providing of Air terminals as per IS-IEC -62305 part-3 Nominal size Ø10/16 mm aluminium rod: 2 Mtr Airterminal: semi-hard (E-AlMgSiO5 corresponds to DIN 48801) Suitable for high wind load. Tested as per IEC 62561. Make-OBO/Dehn/ABB
257	Supply for Providing of Stand for Fang Fix system 16 kg with base and clamp ,made up of frost resistant concrete and clamp tested upto 100KA lightning current . Make-OBO/Dehn/ABB
258	Supply for Providing of Stand for Fang Fix system 16 kg made up of frost resistant concrete. Make-OBO/Dehn/ABB
259	Supply of Test Joint (Folding Clamp) suitable to connect 8mm round conductor and max by 30x3 mm GI strip as specified in drawing and directed by Engineer. Tested for 100kA lightning current. Make-OBO/Dehn/ABB
260	Supply of IP 66 Poly Propylene Junction Box. Installation at 1Mtr Height For Test Joint .Internal dimensions: 100x100x48 mm Make OBO/Dehn/ABB
261	Supply of Galvanised Steel Flat 30X3 mm thickness from earth electrode directly in ground as required. Flat conductor Hot Dipped Galvanized. Tested as per IEC 62561. Make-OBO/Dehn/ABB
262	Supply for Providing of Cross connector for Flat: Suitable for 30mm Galvanised steel strip. Installed with 4 nos of hexagonal plate. Tested for 100kA lightning current. Make-OBO/Dehn/ABB
263	Supply of flat conductor holder- Fit: FL 30, With mounting hole 6.2 x 22 mm, With 2 cylinder bolts M6 x 16 and over-piece from hot-dip galvanised steel, Bottom section from polyamide, black. Tested as per IEC 62561. Make-OBO/Dehn/ABB
264	Supply for Providing of Plastic Corrosion Protection strip: Approx 1.1 mm thick. Width 50mm. Made of petrolatum- coated chemical fibre fabric. Make-OBO/Dehn/ABB
265	Supply of UL Listed maintenance free ,Low carbon copper coated earth rod of 3 metre electrode having diameter of 17.2 mm with copper coating thickness of 250micron tested as per IEC 62561-2 Make-OBO/Dehn/ABB
266	Supply of universal clamp made of SS to connect rod with flat conductor Make-OBO/Dehn/ABB
267	Supply of Earth conductivity enhancing mineral compound shall be of 25 kg/pit tested as per IEC 62561-7,TCLP tested Make-OBO/Dehn/ABB
268	Supply of The above arrangements shall be provided with Heavy duty earth champer of 5000kg load bearing capacity to ensure the safety of earthing system Make-OBO/Dehn/ABB
269	Lightning Counter-To count number of lightning strike and it can record the data and time of lightning incident as per IEC 62561 as per direction of EIC.Make-OBO/Dehn/ABB
270	Installation of The above arrangements including all accessories as per Direction of Engg. In charge.
271	60KVA UPS :Supply ,installation ,testing & commissioning of 60KVA UPS SYSTEM WITH IGBT based inverter system, true online double conversion system, inbuilt isolation transformer & automatic phase sequence corrector of 3ph in put to 3 ph output,415V, with built in BMS with battery back up up to 30 minutes with MS Rack for battery Housing, DC cable 7 Mtr with SFU and links for installation (Battery required: 12V, 84AH, 60 No.s) protection for fault by OL,UV,EF,GF,OC,Ph. (Make:Numeric/APC/ Vertiv/) as per direction of Engg.-in-Charge.
272	DG SET:- Supply, Transportation, erection, testing and commissioning of 3 Phase, 415V, 50Hz, water cooled multi cylinder diesel generator set with alternator of prime rated 750KVA out put contineous rating directly coupled Engine and Alternator with guard and mounted on a common base plate of Robust construction and complete with AMF panel having IP-52 protection, Acoustic Enclosure as per CPCB IV+ norms , sound absorbing material, to restrict sound level up to 75 dB up to 1 mtr distance and as per CPCB IV + norms etc as per following specifications mentioned below.Warrentee period of panel must be 2 years. ALTERNATOR:The alternator of the output rating shall be 3 Phase, 415V, 50Hz, Ac , 0.8 P.F. lagging at 1500 RPM. The alternator is self excited, self regulated, and shall confirm to IS: 13364 of 1992 with regulation of +5% from no load to full load. degree of protections shall be IP21.ENGINE:. Diesel Engine start, developing suitable BHP output at 1500 RPM with mechanical / electronic governing so as to enable the alternator to give 750KVA continuous output at 0.8 P.F. lagging at NTP conditions. The diesel engine shall be capable of providing 10% O/L for 1 Hr for every 12 Hrs of continuous running at full load. The engine with 1st filling of oil and Diesel etc.01. Exhaust pipe of required size and length with insulation or clading.02. Diesel tank suitable for 8 to 12 Hours running capacity.03. Industrial Silencer. 04. SMF Batteries with leads as per the Manufacturer standards,BASE PLATE: Common Base Plate of required size for mounting of Engine Alternator Set fabricated from MS Channerl and vibration damping arrangement with cushy foor mounting including paintng etc. as required. FOUNDATION: Suitable size Cement Concrete (1:2:4) foundation duly plastered and finished with neat coat Cement as required along with smoke exhaust system piping including base frame of structure & lightening protection system. *It also includes control cable of 15mtr 2.5sqmm 6core , civil foundation work.
273	AREA LIGHTING:-S/F of Street light- 90W,120 lm/w efficacy ,IP PC Lens new generation energy saving & environmental friendly long life versatile pressure die-cast alluminium IP66 roadway luminaire with high power LED as light source with acrylic cover(Make: Panasonic/LT/Havells /Philips/Wipro /Crompton/Bajaj) (5Years Warranty)
274	Supply of 6 mtr long hot dip Galvanized Octagonal pole manufactured from HT steel as per BS EN 10025/IS 2062 having minimum yield strength of 350 N/ SQMM having top dia of 70 MM A/F and bottom dia of 130 MM A/F of 3 mm thick or more , base plate as per IS 2062 complete with 4 nos. En 8 grade foundation bolts to withstand basic wind speed of 180 KM/HR wind speed (As per structural calculation of pole manufacturer )or more (Make of poles: Utkarsh/Bajaj/RR Ispat/Vakrangee as per direction of Engg. in Charge.
275	Installation of pole by making the suitable size foundation by embeding the pole 1 mtr into the ground with necessary civil work and fixing the light on the pole equievalant make ISI marked as approved as per direction of Engg. in Charge.
276	SITC OF 1Mtr Decorative Arm. (Make of poles: Utkarsh/Bajaj/RR Ispat/Vakrangee as per direction of Engg. in Charge.
277	Supplying, Erection, Fixing, connection & testing of LED BOUNDRY WALL Light of elegant look (Make: Panasonic/LT/Havells /Philips/Wipro /Crompton/Bajaj) 35 W LED street light having die cast aluminium housing with toughened glass having lumen efficacy of 110 lm/w or more (As per LM 79 report of third party NABL lab) ,IP 65 protection or more , LED street light model having warrantied for a period of 5 years . The luminaire should be supplied along with bracket maintenance free for inspection as required as per direction of Engg.-in-Charge.
278	Supplying, Erection, Fixing, connection & testing of 40W LED GATE Light of (Make: Panasonic/LT/Havells /Philips/Wipro /Crompton/Bajaj) maintenance free having 2 years warranty G.I P ipe with braket including MCB box & including with foundation as per the Drawing for inspection as required & as per direction of Engg.-in-Charge.
279	Supply, Installation, Testing & Commissioning of of IP65 (10-12)w Bollard Fixture with Body made of Extruded Aluminium /Mild steel Pole & PDC Aluminium Housing for Optimal thermal Conductivity. With UV Stabilized Injection Moulded Diffuser for Soft and even light distribution. High Efficiency Driver with necessary safety Protection against Short Circuit, Miswiring,Over Voltage and Surge Protection of upto 10kV ( 4kV Internal and 10kV External SPD of IP67) THD<10%. CRI>70, PF>.95. CCT - 5700/4000/3000K.Impact Resistance IK05.Operating Voltage Between (100-275)V. Avg life of 50,000 Burning [email protected] the light fixture and the Driver Should be BIS Approved.Before final procurement, the final design shall be approved by the concerned client and Engineer-in-charge. Make-K-LITE( Model-Prince Orna Rook) /Philips/LT/PANASONIC/Havells/Bajaj/Crompton/Wipro
280	Supplying,installation,testing & commissioning Of Earthing with copper earth plate 600 mm x 600mm x 6 mm thick ISI marked including accessories and providing masonary with cover plate having loccking arrangement and watering pipe etc (WITH charcoal and salt) as required as per direction of Engg.-in-Charge.
281	Providing and fixing 25mm x 5 mm GI strip on surface or in recess for connections etc. as required as per direction of Engg.-in-Charge.
282	CABLING: Supplying of one number PVC insulated armoured and PVC sheathed XLPE AL. conductor power cable of 1.1 KV grade POLYCAB/KEI/HAVELLS /RR KABEL/FINOLEX/GLOSTER of following size cables as per direction of Engg.-in-Charge.Ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free after sales service within warranty period for acceptance of materials. 3.5core x 35 sq mm
283	4core x 16 sq mm
284	Laying of PVC Insulated PVC Seated /XLPE power cable of 1.1 kv grade size not exceeding 25 SQ. MM direct in ground in the trench in one horizental formation including excavation ,sand coushing protection covering and refilling the trench etc as required as per direction of Engg.-in -charge.
285	Laying of PVC Insulated PVC Seated /XLPE power cable of 1.1 kv grade size not exceeding 120 SQ. MM From 25 SQ. MM in surface with shaddle and screw etc as required as per direction of Engg.-in -charge.
286	Supplying and making end termination with brass compression gland and aluminium lugs for following mentioned size cable.as per direction of Engg.-in-Charge. 3.5 core x35sq mm
287	4core x 16 sq mm
288	Supplying,laying of 3cx2.5 sq.mm copper flexible cable with insulated cover of reputed make,ISI marked with all other concerned materials as per direction of Engg.-in-Charge. Ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free after sales service within warranty period for acceptance of materials.(POLYCAB/KEI/HAVELLS /RR KABEL/FINOLEX/GLOSTER)
289	Providing,fixing and laying of fallowing dia PN10 HDPE pipe (medium class) in ground complete with fitting incl. trenching(75 mm depth)and refilling as per direction of Engg.-in-Charge. 32mm
290	PASSENGER LIFT 13(P)-Supply, Installation, Testing & Commissioning of 15 (Fifteen) 1020 kg Passenger lift gearless with Machine room,Elevator G+4 Floors with With Shaft Sige-Front To Back-2390mm Left To Right-2345mm , ACVVVF drive/ ARD, 2 hr. Fire rated door,>=1.5 MPS with simplex Collective Selective Control without attendant car position indicators, battery operated alarm bell & emergency light, Ss interior with white granite flooring car interior, centre opening automatic sliding stainless steel Silver Sky finish doors for car entrance, civil electrical materials as specified eg.SS Material shall be of grade-SS304 and thickness not less than 1.2mm. Machine beams, buffer support channels, facia plate including sills pit ladder metal screen in Elevator pit etc.as per specification including cost of (i)Overload detection, (ii)Voice announcement, (iii) Intercom, (iv)Brailie Buttons (v) provision of flat cat6 cable for CCTV with all Civil & Electrical works required for installation of Elevator in the existing lift well and machine room, scaffolding ,floor cutting etc. Hoist way wiring and other associated wiring including Fireman's switch complete in all respect as per direction of Engineer in charge. The Elevator should be suitable for physically handicapped person. Make:- OTIS/Mitsubishi/Schindler.
291	FIRE EXTINGUISHERS :- Providing & fixing ABC type (Dry powder type) extinguishers. Including all accessories as per IS specification (IS :15683) Consisting of welded MS cylindrical body with discharge hose ,discharge valve ,suspension brackets,initial filling etc. complete as required., initial filling etc complete as required. Capacity - 6 kg . Make : Fireshiled/ Kanex/ Safex/ ceasefire/Flameklog
292	Providing & fixing Water based Carbon-di-oxide 4.5 ltrs. fire extinguishers as per IS specification consisting of welded MS cylindrical body ,squeeze lever discharge valve fitted with internal discharge tube ,30 cm long high pressure discharge hose ,discharge nozzle,suspension brackets,finished exteranally with red enemel paint and fixed to wall with brackets with rawl plug/dash fastners complete with initial charging. Make : Fireshield/Kanex/ Safex/ ceasefire/Flameklog
293	SITC of 2 kg capacity Eco friendly stored pressure type filled with HFC 236(Clean agent fire extinguisher having zero ozone depletion potential) clean agent fire extinguisher s with safety seal,pressure gauge, controlable discharge mechanism helium leak detection tested and confirming to IS:15683 complete with initial charge as required. Make : Fireshield/Kanex/ Safex/ ceasefire/Flameklog
294	Supplying and installing at approved location approved make fire buckets at 24 gauge galvanized stseel sheet, standard 9 liters capacity and of round bottom shape, painted white inside and red outside and black on the bottom, inscribed with letter \\"FIRE\\" in black and gold. Cost shall be inclusive of Providing MS stand duly painted over a coat of primer (one stand shall be suitable for hanging 5 buckets.
295	SIGNAGES: SITC flexyl of Photoluminescent based Glow-in-the-dark sheeting with luminious properties enclosed in a weather-proof UV stabilized film with UV screen printing by imported inks pasted over 3 mm Thick Cast Acrylic Sheet with the Protection of 3 mm Thick Cast Acrylic from Front side with stud type mirror screw with lifespan of 5 years, visible upto 4-6 hrs in total darkness for floor indication, fire exit, hydrant, hose reel, fire extinguisher, MCP, fire alarm panel, in case of fire, lift, alarm valve signages
296	SIGNAGES: SITC flexyl of Photoluminescent based Glow-in-the-dark sheeting with luminious properties enclosed in a weather-proof UV stabilized film with UV screen printing by imported inks pasted over 5 mm Thick Cast Acrylic Sheet with the Protection of 3 mm Thick Cast Acrylic from Front side with stud type mirror screw with lifespan of 5 years, visible upto 4-6 hrs in total darkness for fire evacuation plan, fire action(For all floors)
297	CCTV WORKS: Supply, Installation, Testing & Commissioning of 5MP IP Network TDN Low-Light IR motorized Lens Dome/Bullet Camera, 1/2.8\\" CMOS or better, 5MP (2592 x 1944) @ 25fps or better, four stream at various resolution & Frame Rates, Min. Illumination required 0.005 lux (color), 0 Lux IR On, 3 IR LEDs, Smart IR with upto 70m(bullet)/50m(dome) IR distance, Auto ICR (Infrared Cut Filter) 130dB True WDR, S/N Ratio 55db, Shutter Speed 1/3 - 1/100,000; Adavance Video Compression technology such as H.265 HEVC/ H.264 / MJPEG , Fixed Lens 2.7-13.5mm motorized, Field of View FoV H:100-28.5°, V:73-21.4°, BLC, HLC, WDR, 2D/3DNR, White Balance - Auto/Manual/Day/Night/timing, Minimum Edge Intelligence Video Analytics : Video Motion Detection, Tampering, Loitering, Intrusion, & People Counting, 5 Privacy Mask, 6 Region Of Intreset, Defog, HTTPS, IP Filter, TLS1.2, AES-128/256, SSH/Telnet closed, Stream Encryption, 2TB SD card support, PoE (802.3 af) and 12V DC, IP 66/67 & IK10 Vandal proof with Die Cast Aluminium Housing, Having Operating temp range : –30°C to 60° C. Certifications: ONVIF Profile S/G/T compliant,, CE (EN 50130-4), FCC Part 15, EN 55032 & RoHS (EN63000),NDA,STQC compliant. Make-Honeywell value series/Pelco/Axis/Bosch
298	Supply, Installation, Testing & Commissioning of 5MP IP Network TDN Low-Light IR Fixed Lens Dome/Bullet Camera, 1/2.8\\" CMOS or better, 5MP (2592 x 1944) @ 25fps or better, four stream at various resolution & Frame Rates, Min. Illumination required 0.005 lux (color), 0 Lux IR On, 3 IR LEDs, Smart IR with upto 50m(bullet)/40m(dome) IR distance, Auto ICR (Infrared Cut Filter) 130dB True WDR, S/N Ratio 55db, Shutter Speed 1/3 - 1/100,000; Adavance Video Compression technology such as H.265 HEVC/ H.264 / MJPEG , Fixed Lens 2.8mm(Dome)/3.6mm(bullet), Field of View FoV H:96.5°, V:73.8°(dome)/ Field of View FoV H:94.1°, V:71°(bullet), BLC, HLC, WDR, 2D/3DNR, White Balance - Auto/Manual/Day/Night/timing, Minimum Edge Intelligence Video Analytics : Video Motion Detection, Tampering, Loitering, Intrusion, & People Counting, 5 Privacy Mask, 6 Region Of Intreset, Defog, HTTPS, IP Filter, TLS1.2, AES-128/256, SSH/Telnet closed, Stream Encryption, 2TB SD card support, PoE (802.3 af) and 12V DC, IP 66/67 & IK10 Vandal proof with Die Cast Aluminium Housing, Having Operating temp range : –30°C to 60° C. Certifications: ONVIF Profile S/G/T compliant,, CE (EN 50130-4), FCC Part 15, EN 55032 & RoHS (EN63000),NDA,STQC compliant. Make-Honeywell Value series/Pelco/Axis/Bosch
299	Supply , Installation, testing , commissioning of 64 Channel NVR with 8 SATA; 384 Mbps incoming bandwidth, Up to 8 Megapixels Resolution Display and Recording, H.265 video compression technology with real time encoding, Full function CMS (Central monitoring software) supported, Two way audio supported, Dual streaming technology to encode recording stream and network stream separately, Supports remote monitoring on Mobile Client (Android, IOS), TCP / IP, PPPoE, DHCP, DNS, DDNS, UPnP, NTP, SMTP, Time/ Date, Alarm, Motion Detection & Exact Search (accurate to second), Record Snapshot, FTP, Preset Calling, Email notification supported, Manual/ Alarm/ Motion Detection/ Continuous, CE, FCC, RoHS). Make-Honeywell value series/ Pelco/ Axis/ Bosch
300	Supply, Installation,Testing & Commisioning of Surveliance 10 TB HDD. Make:- WD/ Segate/ Toshiba
301	Supplying and drawing following core Fiber Optic Cable having corrugated steel armoring. The Fiber should be SM Fiber Central -loose tube filled with Thixotropic jelly, duly following Standards: ISO 11801, IEC 60793-1/60794-1-2, ITU-T-REC G.652D and Telecordia GR-20-core, High quality Electro Chromium Coated Corrugated Steel tape (ECCS ) and HDPE- Sheath, Operating ambient Temperature should be – 5 0C to +50 0C and Storage Temperatureshall be – 5 0C to +50 0C, Max Attenuation ± 0.36 (db/ km) at Operational Wavelength 1310 nm and ± 0.22 db / km at Operational Wavelength 1550 nm. type of fiber should be 9/125 / G.652D & Refractive Index should be 1.4670/1.4675. The value for Mode-filed, Cladding Diameter 9.2 ± 0.4 µm and 125 ± 0.7 µm correspondingly. The Dispersion value < 3.5 < 18 ps/nm-km and PMD value < 0.2 ps/km and Cable Cutoff wavelength < 1260 nm i/c splicing & marking etc complete as required. Single Mode 12 Core Optical fiber cable.Make-Systimax/Legrand/Panduit
302	SITC of Rack mount Draw Type 24 port Loaded LIU available in Standard 19” ,Dimensions (mm) : 430 X 220 X 1U , Cold Rolled Steel as Raw Material , Consist of Top Cover and Bottom Panel , Easy to Assemble and Dissemble , Three Types of Input Holes Cable Entry Through Water Proof Cable Clamp , 12 Duplex SC or LC Adapter Interface , Splice 24 Fibers at Most with 1 Tray ,Adaptor, SM, Duplex SC, PC Type ,Support the TIA/EIA Telecommunication Wiring Standards. Compact Design , Telcordia GR-326-Core . Make: Systimax/ Legrand/ Panduit
303	SITC of Pigtail, SM (OS2), SIMPLEX SC, PC TYPE, 1M, LSZH ,Insertion Loss : <= 0.2 db, Max 0.3db/MTRJ: Max 0.5db Return Loss : PC>= 45db, UPC>=50db, APC>=60db ,LSZH Jacket-Reduced Toxic Gasses Emitted During Combustion , 100% Factory Tested , Low Insertion Loss and Return Loss. Make-Systimax/Legrand/Panduit
304	SITC of Cat 6, 24-port loaded, 1U Modular Jack Panel Should accommodate Cat6 with Rear Cable Management and Front removable Tooless Information outlet. Should have easy clip management with labels and clear label covers, Made with of Dicast Aluminium Alloy Material and Non Corrosive with Cat6 toolless RJ45 x 24 ports with color code front panel with patch cord locking. Make: Systimax/ Legrand/ Panduit
305	SITC of Cat6 UTP 24 AWG Patch Cord Patch cord: 6 UTP Patch Cords are Factory Tested for Better Quality and Suitable for the High Speed Data Transmission. Complies to the Standard ANSI/TIA/EIA-568-C.2 Standard. Supports Data Networks Speeds Up to 10/100-Base-T and 1000-Base-T. Available In LSZH Jacket- Reduced Toxic Gasses Emitted During Combustion , RJ45, 8P8C, 2 FORK 50μ’’ Gold Plated Contacts , 100% Factory Tested , Transparent Boot Cable Assemblies. Make: Systimax/ Legrand/ Panduit(1 mtr length)
306	SITC of 24 Port Layer 2 PoE+ Switch having 24 x 10/100/1000 Mbps Ethernet PoE+ ports with 4 x 1/10Gig SFP+ ports ,1 x RJ45 port console port ,Switching Capacity 128 Gbps , Throughput 96 Mpps ,MAC Address 16k , Switch should support IEEE 802.3af (15.4W) & IEEE 802.3at (30W). Total PoE power: 370W or above , Switch should support DHCP server/relay/client, DHCP snooping/option82 , Switch should support Console, Telnet, SSH v1/2, HTTP, HTTPS, SNMP v1/v2/v3, RMON , TFTP, FTP, SFTP, NTP, ZTP, SPAN, RSPAN,Switch should support support ICMPv6, DHCPv6, ACLv6 ,IPV6 Telnet ,Temperature 0°C -50°C ,Power Supply AC: 100-240V. Make: Digisol/ Cisco/ HP/ Netgear
307	SITC of 1G-LX/LH SFP transceiver module,SMF, 1310nm, 9/125 um Single mode Fiber Type up to 20 KM. Make: Cisco/ Digisol/ Netgear
308	SITC of 40G Ethernet Routing Switch having 8 x 10/100/1000Base-T (RJ45) + 24 x 10GbE (SFP+) + 2 x 40GbE(QSFP+), 1 x RJ45 Ethernet Management port , 1x Console port ,1x USB2.0 interface , Switching Capacity 656Gbps , Throughput 488Mpps , MAC Address 32K ,Routing Table 16K ,Jumbo Frame 10k , Switch Supports Standard and Expanded ACL Based on source/destination IP or MAC, IP Protocol, TCP/UDP port, DSCP, ToS, IP Precedence), VLAN, Tag/Untag, CoS ,MLDv1/v2, PIM-SM/DM for IPv6, IPv6 Any Cast RP, IPv6 ACL, IPv6 QoS ,Switch have CLI, WEB, Telnet, SNMPv1/v2c/v3 through IPv4 and IPv6 ,Switch Supports VSF(Virtual Switch Framework) , Temperature Working 0°C~50°C, storage -40°C~70°C , Power Supply AC: 100~240VAC, 50~60Hz ,+ 48VDC. Make: Digisol, Cisco, HP, Netgear
309	SITC of 55\\" UHD IPS Commercial Digital Display for Small Size Discussion & Chambers: Brightness (440 nits or higher), Dynamic Contrast Ratio (Dynamic MCI (Hz)):1000000:1), 1000000:1, Static (Panel) Contrast Ratio-1200:1, Response Time (G to G)-8 ms, Refresh Rate.-60 Hz, Life span (hrs)-30,000, Speaker (Sound Output):10W + 10W, Speaker System: 2.0 ch, DVB-T2/C Broadcasting System, Commercial Smart UX, webOS version (webOS 6.0), BIS Certification with 3 years onsite warrenty. Make: LG/ Samsung/ Sony
310	SITC of 9U/500D Wall Mount Rack with Accessories: The rack size should be 600W x 500D, Front frame integrated with top, bottom, front and two side panels for better rigidity and strength, Front Glass Door with Lock loaded, Compliance with standards shall be UL 2416., DIN 41494, IEC EN 60529, IEC EN 62262 , IEC EN 60068-2-11 , ISO 9001:2008 including Power Distribution Unit (06/16 Amp Indian-Standard - 06 Socket - Single Pole / Screw Mountable / 16 Amp MCB / Alternating Current - 16 Amp 3 Pin Plug with Power Cable 2.5 sq.mm 3 meter Lengt), 1 cooling Fan(230V AC - 90 CFM, dB 42), 2nos 1U Metal Cable manager with Plastic cable loops and H/W screw. Make:Valrack, Rittal, Legrand
311	SITC of 42U 600/1000D UL Listed Floor mount Rack with Front perforated door with 3 point lock, Rear mesh door with Cam lock and 3inch Castor Wheel included with 2 no 6/16 Amp Indian-Standard - 06 Socket - Single Pole / Screw Mountable / 16 Amp MCB / Alternating Current - 16 Amp 3 Pin Plug with Power Cable 2.5 sq.mm 3 meter Length, 4nos 1U Metal Cable manager with Plastic cable loops, 2nos CFM FAN set, 1no Monitor Tray - Ventilation - 495W - 375D and H/W screw920sets). Make:Valrack, Rittal, Legrand
312	Supply Installation Tetsting and Comissioning of HDMI EXTENDER. MAKE - mx
313	SITC of Certified HDMI® Interface Cable, 18 Gbps, 15 m Makes: Honeywell, Extron, Kramer
314	AV SYSTEM:- SITC of Active LED wall of Pixel pitch:-2.5mm or higher of better minimum size 21 ft x12.6 Ft or higher predefined 4K resolution according to pixel pitch 2560x1536 or higher, includes LED cabinets, 4K LED controller & software, pixel density per sqm 160000 or better, viewing angel 160/160 or better, cabinet 640 x 480 x 55mm cable and accessories and associated civil work, refresh rate 3840 hz or more, minimum brightness 800 nits or more, power consumption (Maximum/ power consumption-550w/sqm or lower) approx, life time of 100000 hour or more, Contrast ratio 8000:1 or more with controller, with 2 years warranty, Inbuilt 4K picture facility Make:-Barco, Delta, Christie
315	SITC of 75\\" UHD Smart Display with Brightness-500 Nits, 24x7, Haze-28% or more, 3 x HDMI IN,1x HDMI Port Out ,3X USB Port, (2x2.0, 1X2.0, 1X Type C),Inbuilt OPS Slot , 1 Audio Input,Bluetooth, Built-In WI-FI, 32 GB Inbuilt Memory, 4 GB RAM, Built In Android 11 OS,RS232C -1, RJ45 -1 or more, Landscpae & Portrait both, Inbuilt Speaker-20W(10W x 2) or above. Make- Panasonic, LG, Samsung
316	SITC of AI based Full HD 1080p @ 60fps Presenter PTZ Tracking Camera with Dual Camera- one PTZ Camera for Presenter Tracking and second fixed lens Panoramic Camera. PTZ Presenter Camera should support min 20X Optical Zoom and 12x Digital Zoom with Panning range of +170 deg to - 170 deg and Tilt Range of -30 to +90 Degrees, Field of View for PTZ Camera should be min 58 Degree and for Panoramic Camera min. 100 Degree, camera should support simultaneous outputs through HDMI, 3G-SDI, USB 3.0 and IP with 1x Audio In and can be controlled via RS232 and IP. Should support multiple video streams. Tracking Camera should support Everywhere Tracking, Partition Tracking, Auto Framing & Gesture Control. Should support PoE and Virtual USB Driver. Quoted model should be BIS, CE, FCC , Clickshare & RoHS Certified with Test Lab Reports. Make: Lumens, Panasonic, Sony, Vaddio
317	SITC of 4K @60fps PTZ Camera with minimum 30X Optical Zoom & FoV of minimum 68 deg , min 255 Presets. Camera should support simultaneous outputs through Ethernet, HDMI, 3G-SDI, Audio In and can be controlled via RS232 & 422 In & Out & IP.Panning angle -170° ~ +170°, Tilting angle -30° ~ +90° . The tilting and panning speed of camera should be minimum 300° per second. Camera should support SRT, FreeD Protocol, PoE and Virtual USB Driver. Quoted model should be BIS, CE, FCC & RoHS Certified with Test Lab Reports.Make: Lumens, Panasonic, Sony, Vaddio
318	SITC of Recording, Streaming & Webcasting Hardware simultaneously, Built-in 4x HDMI & IP Inputs with 4x Line Inputs, 2x HDMI Outputs. The system should be capable to record upto any four inputs simultaneously in a single frame and as well as individual sources simultaneously. Should have minimum 1TB inbuilt storage and can be connected to local NAS storage. The system should be able to support minimum 3 unicast streams.The recorded files should have the option of time and date stamp. Quoted model should be CE, FCC & RoHS Certified with Test Lab Reports.Make: Lumens, Arec, Panasonic, Sony, Vaddio
319	SITC of AVoIP Decoder supporting 4K @60fps with simultaneous outputs through HDMI 2.0, USB Type C & USB Type A with Line Out & 3.5 mm, 1x Line In & 3.5 mm. The decoder should be capable to convert IP to USB 3.0 & HDMI. The decoder should support Video Decoding Formats of H.264/HEVC with in-built AES128 encryption and NDI HX3 / NDI HX2 / RTSP, PoE+Make: Lumens, Crestron, Extron, AMX
320	SITC of Digital Podium with Built-in highly sensitive Interactive Panel with adjustable Motorized tilt. Display Size 21 inch or higher. Resolution 1920 x 1080 Full HD or better. Brightness 350 cd/m² (typ) or higher. Connectivity (Minimum) USB x 1, HDMIx 1, DVI x 1, VGA x 1 or better. Battry Free EM Pen. Processor: Intel Core i5 (10th Gen or better processor), RAM 8 GB, Storage 256 GB SSD or better. Controller: Ports on front Panel of Controller (Minimum): VGA,HDMI,USB3.0x2,Audio IN or more. Full HD Visualizer: Camera Sensor 1/4\\"CMOS Sensor F=2.8, Effective Pixels Min. 8 Mega Pixel or better, Frame Rate Min. 30fps or better, Two Type LED system Top LED & Side LED strip.Make: Globus, AHA, UNI
321	SITC of 15\\" high performance 2-way loudspeaker Black version with Drivers HF Compression driver with 1.7\\" VC and 1\\" throat, LF 15\\", Peak power handling 2000 W, RMS/AES power handling 500 W, Frequency Response 50 Hz - 20 kHz, Impedance 8 Ω, Sound Pressure (Max. W/1m) 127 dB Approved Make: Audac/ Pulz/ Martin Audio
322	SITC of 18” Horn loaded subwoofer cabinet with Peak power handling 3200 W, RMS/AES power handling 800 W, Impedance 8 Ω, Sound Pressure (Max. W/1m) 131 dB, Frequency Response 37 Hz - 130 Hz. Approved Make:Audac/ Pulz/ Martin Audio
323	SITC of 3-way high outputs speaker cabinet with Peak power handling 3000 W, RMS/AES power handling 750 W, Impedance 8 Ω, Sound Pressure (Max. W/1m) 134 dB, Frequency Response 130 Hz - 20 kHz. Approved Make: Audac/ Pulz/ Martin Audio
324	SITC of Ceiling flying system mounting bracket.
325	SITC of high-output loudspeaker cabinet, featuring an 8” high efficiency mid/low range driver and 1” compression driver fitted with a 100° x 80° coverage horn, providing a powerful and detailed sound in a compact cabinet.Speaker type 2-way, Peak power handling 700 W, RMS/AES power handling 175 W, Impedance 8 Ω.Approved Make: Audac/ Pulz/ Martin Audio
326	SITC of Quad channel power amplifiers with RMS/AES power handling @ 4 Ω Stereo 4 x 750 W, @ 8 Ω Stereo 4 x 380 W, @ 8 Ω Bridge 2 x 1500 W, Frequency Response (± 3 dB) 20 Hz - 20 kHz, Signal / Noise > 95 dB, Technology Class-D, Protection: DC Short circuit, Over heating, Over load, Signal limiting, Loudspeaker Power limiter, Cooling Temperature controlled fan. Approved Make: Audac/ Pulz/ Martin Audio
327	SITC of Digital Signal Processor with Full rack 19” 1RU processor mainframe with sixteen user-configured card slots. Selectable 48 & 96kHz sampling rates. Integrated license-activated AEC. Dual core processing 40-bit floating DSP .Front panel OLED display with jog wheel. Rear panel includes an Ethernet module with RJ45 connector and internal power supply connection with built-in MOD-Dante-ETH module already pre-installed into the Dante mainframe to provide 64x64 I/O channels of Dante network audio. Dual RJ45 Dante and single RJ45 Ethernet connectors.52ch Mic/Line input with selectable mic, line, mic gain, and phantom power per input. 32-bit analog to digital converters.28ch Line output. 32-bit digital to analog converters. USB 2.0 to Dante network endpoint, PoE-powered with single CatX cable.Software license activated AEC. 8ch of AEC @ 250ms delay / 16ch @ 100ms. Make: Xilica, Ashly, Pulz Audio
328	SITC of pre-polarized condenser gooseneck microphone with overall length of 450mm or better have an integrated light ring, with XLR5M-type connector with , shall offer radio frequency interference (RFI) shielding against intermodulation from wireless equipment or devices, cardioid microphone capsule with uniform 120° angle of acceptance (-3dB) or better, frequency response of 50 Hz to 20,000 Hz or better and sound input levels handling capability of minimum 130 dBspl or better, nominal equivalent noise level of 26 Dba or better and output shall be low impedance balanced (<100 ohms) with current consumption shall be 3 mA or better. Make: Sennheiser, Clock Audio, Rode
329	SITC of table stand with Microphone modes Toggle on / off, Push to mute, Push to talk, permanent on for connecting and operating XLR gooseneck microphones with XLR-5F microphone input and an XLR-3M microphone output operating on 48 V phantom power and current consumption of 3.7 mA or better. Make: Sennheiser, Clock Audio, Rode
330	SITC of Podium Microphone of gooseneck stem with overall length of 550 - 600 mm with a pre-amp along with its XLR-3 connector. For set-up as table mount or shock mount.Hyper cardoid capsule, 12 to 48V phantom power, frequency response of 40Hz to 20kHz or better, equivalent noise level maximum 23 dB weightedA or better. Impedance 50 Ohm or better, Minimal terminating impedance 1 kOhm or better, Maximum sound pressure level 130 dB SPL or better with gold plated electrical contact points.Table stand with Microphone modes Toggle on / off, Push to mute, Push to talk, permanent on for connecting and operating XLR gooseneck microphones with XLR-3F microphone input and an XLR-3M microphone output operating on 48 V phantom power and current consumption of 3.7 mA or better. Make: Sennheiser, Clock Audio, Rode
331	SITC of Digital wireless handheld Microphone with UHF transmission greatly enhances range, reliability and scalability of 56 MHz Bandwidth will allow for up to 90 channels Up to 2,200 or more selectable frequencies with Mobile App integration setup 134 dB or more transmitter dynamic range Lithium Ion battery pack delivers up to 10 hours of operation (up to 6 hours of operation with AA batteries) Transducer principle dynamic with Pick-up pattern cardioid, Sound pressure level 154 dB SPL, Transmit power : 10 mW. Make: Sennheiser, Clock Audio, Rode
332	SITC of Digital wireless lavalier Microphone with UHF transmission greatly enhances range, reliability and scalability of 56 MHz Bandwidth will allow for up to 90 channels Up to 2,200 or more selectable frequencies with Mobile App integration setup 134 dB or more transmitter dynamic range Lithium Ion battery pack delivers up to 10 hours of operation (up to 6 hours of operation with AA batteries) Transducer principle dynamic with Pick-up pattern omnidirectional, Sound pressure level 130 dB SPL, Transmit power : 10 mW. Make: Sennheiser, Clock Audio, Rode
333	SITC of active antenna splitter 2 x 1:4 or 1 x 1:8, Digital transmission operating in the UHF spectrum , Auto scan features, 134 dB or better audio input dynamic range , 56 MHz of tuning bandwidth and provision up to 90 channels, 2,200 or more selectable frequencies. Bidder Shall Submitted OEM Authorizationalong with technical bid Make: Sennheiser, Clock Audio, Rode
334	SITC of digital directional antenna with Impedance:50 Ohm; Connector: BNC; Pick-up pattern: directional;Frequency range: 470 - 1075 MHz or better;Antenna gain: 5 dBi or better; Bidder Shall Submitted OEM Authorizationalong with technical bid Make: Sennheiser, Clock Audio, Rode
335	SITC ANTENNA BOOSTER with 56 MHz of tuning bandwidth and provision up to 90 channels, 2,200 or more selectable frequencies. Bidder Shall Submitted OEM Authorizationalong with technical bid Make: Sennheiser, Clock Audio, Rode
336	SITC of dynamic cardioid vocal microphone with frequency response of 40 Hz – 16,000 Hz or better and the sensitivity of 2.7 mV/Pa at 1 kHz or better, nominal impedance of 350 Ohm or better, with a min. terminating impedance of 1 k Ohm. Bidder Shall Submitted OEM Authorizationalong with technical bid Make: Sennheiser, Clock Audio, Rode
337	SITC of super-cardioid pre-polarized condenser instrument microphone with frequency response of 40 Hz- 20,000 Hz or better and sensitivity of 3 mV/P at 1 kHz or better , Maximum SPL of 139 dB at 1 kHz. Nominal impedance of 50 Ohm or better, with a min. terminating impedance of 1 kOhm or better. Bidder Shall Submitted OEM Authorizationalong with technical bid Make: Sennheiser, Clock Audio, Rode
338	SITC of 32 Channel Mixer with 32 mono channels, 2 dual stereo inputs with 4-band EQ, 4-band EQ with 2 swept mids and in/out switch, 4 sub groups fed from each channel, 12 bar meters, Individual channel 48V phantom power, Configurable USB stereo audio in/out.Make: Yamaha, Allen & Health, Behringer
339	SITC of secured 4K wireless presentation device having 1x HDMI Input, 1xHDMI output & stereo line-level audio output.User should be able to present content via OS Supported Apple iOS, Android, Windows 8.1 or higher, Windows 10, macOS, Chrome OS, Miracast™ screen mirroring technology.Able to view minimum four content side by side on the single screen and Device should have HDMI Output port supporting HDCP 2.2, EDID, CEC & multiple USB port for connecting peripherals. Should have ethernet port supporting 100/1000 Mbps, TCP/IP, UDP/IP, DHCP, SSL, SSH, IEEE 802.1x, Active Directory authentication, HTTPS.Standard network security protocols, including 802.1x network access control, AES content encryption, to protect privacy and ensure compliance with your organization’s IT policies.Video out resolution up-to 4k. Device should have 1x RS-232 bidirectional & 1x IR port for third party device control. Should be able to create separate guest network for data sharing. Should be shipped with 1x USB Dongle for wireless 4k content sharing, without downloading any application, without running OEM app, without plugin, for external guests. Supplied 1xUSB dongle must have 2xbuttons on it, where one will be used for sharing content and second button to enable the wireless conferencing feature when required. Should support Wifi 6 communication between 1x USB dongle and wireless presenter hardware.Should comply to IC, CE, FCC (Additional BIS to be shared if applicable)Make: Crestron, Extron, Barco, Kramer
340	SITC of Transmitter/Wall Plate Type for HDMI, RS 232, and IR Signal extension up-to 40m. Should support video signals HDR10+, Dolby Vision, Deep Color and 4096x2160 @60 4:4:4 resolution. Should support audio signals Dolby Digital EX, Dolby Digital Plus, Dolby TrueHD, Dolby Atmos, DTS-ES, DTS HD High Res, DTS-HD Master Audio & LPCM up to 8 channels. Should support HDCP 2.3 content protection. Should have 1x HDMI Input, 1x RJ45 output, 1x RS-232 & 1xIR. Should pass EDID and CEC. Should comply to CE, IC, FCC.Make: Crestron, Extron, Kramer
341	SITC of Receiver for HDMI, RS 232, and IR Signal extension up-to 40m.Should support video signals HDR10+, Dolby Vision, Deep Color and 4096x2160 @60 4:4:4 resolution. Should support audio signals Dolby Digital EX, Dolby Digital Plus, Dolby TrueHD, Dolby Atmos, DTS-ES, DTS HD High Res, DTS-HD Master Audio & LPCM up to 8 channels.Should support HDCP 2.3 content protection.Should have 1x HDMI Output, 1x RJ45 input, 1x RS-232 & 1xIR.Should pass EDID and CEC.Should comply to CE, IC, FCC.Make: Crestron, Extron, Kramer
342	SITC of 8x8 matrix HDMI AV Switcher. Should have eight HDMI® inputs, eight HDMI outputs and 2x Balanced/unbalanced stereo line-level audio output. Should support video signals HDR10+, Dolby Vision, Deep Color and 4096x2160 @60 4:4:4 resolution. Should support audio signals Dolby Digital EX, Dolby Digital Plus, Dolby TrueHD, Dolby Atmos, DTS-ES, DTS HD High Res, DTS-HD Master Audio & LPCM up to 8 channels. Should support HDCP 2.3 content protection. Should have ethernet port supporting 1000 Mbps, auto-switching, auto-negotiating, auto-discovery, full/half duplex, DHCP, Web browser setup. Should support EDID management & third party device control over CEC. Should support security features and protocols, Active Directory® credential management, 802.1X authentication, TLS, SSH, and HTTPS. Should have minimum1x USB port for firmware, configuration management and to power a USB powered device upto 5 V 500 mA power. Should be controllable over ethernet. Should comply to CE, IC, RoHS, FCC.Make: Crestron, Extron, Kramer
343	SITC of 2.5 square mm, 2 core, speaker cable or better (Speaker Cable) through PVC Conduit. Approved Make: Finolex/KEI/RR Kabel/Gloster/Havells/Krystal/Liberty
344	SITC of laying of 6 sqmm 2 core shielded wire.Approved Make: Krystal/Liberty/Finolex
345	SITC of HDMI Cable 1.8 mtr Makes: Crestron, Extron, Kramer
346	SITC of Snake Cable: Supply and Laying of 8 pair Analog Audio Snake Cable, 24. AWG stranded (7x32) TC conductor, Polyolefin insulation, individually shielded, number or color-coded PVC jackets and shields bonded to stripsimultaneously over all shield and 24 AWG TC drain wire. Make: Krystals/ Kramer/ Belden
347	SITC of Audio Cable. Make: Krystal/Liberty/Finolex
348	SITC of XLR Connector
349	SITC of DI Box having low-impedance (XLR) output.
350	SITC of 42U 600/1000D UL Listed Floor mount Rack with Front perforated door with 3 point lock, Rear mesh door with Cam lock and 3inch Castor Wheel included with 2 no 6/16 Amp Indian-Standard - 06 Socket - Single Pole / Screw Mountable / 16 Amp MCB / Alternating Current - 16 Amp 3 Pin Plug with Power Cable 2.5 sq.mm 3 meter Length, 4nos 1U Metal Cable manager with Plastic cable loops, 2nos CFM FAN set, 1no Monitor Tray - Ventilation - 495W - 375D and H/W screw920sets). Make:Valrack, Rittal, Legrand
351	INTERCOME: Supply and installation of IP PBX System support up to 500 users and minimum 50 concurrent calls, integrated 1 PSTN trunk FXO ports through External Gateway, 1 analog telephone FXS ports with lifeline capability and up to 50 SIP trunk accounts, Gigabit network ports with Integrates PoE, USB, SD card, Supports up to a 5-level IVR (Interactive Voice Response), Supports any SIP video endpoint that uses the H.264, H.263 or H.263+ codecs. Make: Grandstream/ NEC/ Mitel/matrix
352	Supply Installation Tetsting and Comissioning of hardware daughterboard module designed to enhance the voice processing capabilities of Matrix Eternity series PBX systems, including GENX, MENX, LENX, and PENX platforms. It facilitates high-quality VoIP communication by providing simultaneous transcoding for audio calls. Make:-Matrix/CISCO/PANASONIC/GRANDSTREAM
353	Supply Installation Tetsting and Comissioning of Analog Subscriber Line (SLT) expansion card designed specifically for use with Matrix ETERNITY GE series IP-PBX systems. It enables seamless integration of up to 20 analog (single-line) telephones into the unified communication system, making it ideal for businesses that still rely on analog endpoints alongside digital and IP phones. Make:-Matrix/CISCO/GRAND STREAM
354	Supply Installation Tetsting and Comissioning of software license that enables support for 5 additional IP (SIP) subscribers on the Matrix SARVAM UCS (Unified Communication Server) platform. This license allows organizations to register SIP-compliant devices such as IP phones, softphones (like Matrix VARTA), and third-party SIP clients, expanding their VoIP network efficiently. Make:-Matrix/D-LINK/PANASONIC /GRANDSTREAM
355	Supply Installation Tetsting and Comissioning of software license designed to expand the number of expansion slots in the Matrix ETERNITY GENX IP-PBX system. Specifically, it enables the activation of 4 additional universal slots, allowing for greater scalability and flexibility in configuring the system to meet the evolving communication needs of small and medium enterprises (SMEs). Make:-Matrix/CISCO/PANASONIC/GRANDSTREAM
356	Supply, Installation,Testing & Commisioning of IP based PoE Phone with single lie Display with 2 Ethernet Port. Make: Grandstream/ NEC/ Mitel/Matrix
357	Supply Installation Tetsting and Comissioning of analog trunk expansion module designed for the Matrix ETERNITY GENX IP-PBX system. This card enables the integration of 4 analog Central Office (CO) trunk lines, facilitating external PSTN connectivity for voice communication.Make:-Matrix/CISCO/GRAND STREAM
358	Supply Installation Tetsting and Comissioning of Standard telephone handset compatible with analog and IP desk phones. Includes dynamic receiver and electret microphone, coiled RJ-9 cable, ergonomic ABS body.Make:-BEETEL/PANASONIC /PHILIPS/MATRIX/GRANDSTREAM
359	SITC of 24 Port Layer 2 PoE+ Switch having 24 x 10/100/1000 Mbps Ethernet PoE+ ports with 4 x 1/10Gig SFP+ ports ,1 x RJ45 port console port ,Switching Capacity 128 Gbps , Throughput 96 Mpps ,MAC Address 16k , Switch should support IEEE 802.3af (15.4W) & IEEE 802.3at (30W). Total PoE power: 370W or above , Switch should support DHCP server/relay/client, DHCP snooping/option82 , Switch should support Console, Telnet, SSH v1/2, HTTP, HTTPS, SNMP v1/v2/v3, RMON , TFTP, FTP, SFTP, NTP, ZTP, SPAN, RSPAN,Switch should support support ICMPv6, DHCPv6, ACLv6 ,IPV6 Telnet ,Temperature 0°C -50°C ,Power Supply AC: 100-240V. Make: Digisol/ Cisco/ HP/ Netgear
360	Supply & Delivery & Laying of 300 Pair CROWN MDF. Make:- ATEL ELECTRONICS/IDIS INDIA/krone
361	Supply & Delivery & Laying of 50 Pair CROWN D P BOX.MAKE- IDIS India/krone/comstar
362	Supply & Delivery & Laying of 50 Pair Telephone cable.Make:- POLYCAB/DELTON/Finolex
363	SITC of 40G Ethernet Routing Switch having 8 x 10/100/1000Base-T (RJ45) + 24 x 10GbE (SFP+) + 2 x 40GbE(QSFP+), 1 x RJ45 Ethernet Management port , 1x Console port ,1x USB2.0 interface , Switching Capacity 656Gbps , Throughput 488Mpps , MAC Address 32K ,Routing Table 16K ,Jumbo Frame 10k , Switch Supports Standard and Expanded ACL Based on source/destination IP or MAC, IP Protocol, TCP/UDP port, DSCP, ToS, IP Precedence), VLAN, Tag/Untag, CoS ,MLDv1/v2, PIM-SM/DM for IPv6, IPv6 Any Cast RP, IPv6 ACL, IPv6 QoS ,Switch have CLI, WEB, Telnet, SNMPv1/v2c/v3 through IPv4 and IPv6 ,Switch Supports VSF(Virtual Switch Framework) , Temperature Working 0°C~50°C, storage -40°C~70°C , Power Supply AC: 100~240VAC, 50~60Hz ,+ 48VDC. Make: Digisol, Cisco, HP, Netgear
364	NETWORKING: SITC of Rack mount Draw Type 24 port Loaded LIU available in Standard 19” ,Dimensions (mm) : 430 X 220 X 1U , Cold Rolled Steel as Raw Material , Consist of Top Cover and Bottom Panel , Easy to Assemble and Dissemble , Three Types of Input Holes Cable Entry Through Water Proof Cable Clamp , 12 Duplex SC or LC Adapter Interface , Splice 24 Fibers at Most with 1 Tray ,Adaptor, SM, Duplex SC, PC Type ,Support the TIA/EIA Telecommunication Wiring Standards. Compact Design , Telcordia GR-326-Core . Make: Systimax/ Legrand/ Panduit
365	SITC of Pigtail, SM (OS2), SIMPLEX SC, PC TYPE, 1M, LSZH ,Insertion Loss : <= 0.2 db, Max 0.3db/MTRJ: Max 0.5db Return Loss : PC>= 45db, UPC>=50db, APC>=60db ,LSZH Jacket-Reduced Toxic Gasses Emitted During Combustion , 100% Factory Tested , Low Insertion Loss and Return Loss. Make: Systimax, Legrand, Panduit
366	SITC of Cat 6, 24-port loaded, 1U Modular Jack Panel Should accommodate Cat6 with Rear Cable Management and Front removable Tooless Information outlet. Should have easy clip management with labels and clear label covers, Made with of Dicast Aluminium Alloy Material and Non Corrosive with Cat6 toolless RJ45 x 24 ports with color code front panel with patch cord locking. Make: Systimax/ Legrand/ Panduit
367	SITC of Cat6 UTP 24 AWG Patch Cord Patch cord: 6 UTP Patch Cords are Factory Tested for Better Quality and Suitable for the High Speed Data Transmission. Complies to the Standard ANSI/TIA/EIA-568-C.2 Standard. Supports Data Networks Speeds Up to 10/100-Base-T and 1000-Base-T. Available In LSZH Jacket- Reduced Toxic Gasses Emitted During Combustion , RJ45, 8P8C, 2 FORK 50μ’’ Gold Plated Contacts , 100% Factory Tested , Transparent Boot Cable Assemblies. Make: Systimax/ Legrand/ Panduit(1 mtr length)
368	SITC of 24 Port Layer 2 PoE+ Switch having 24 x 10/100/1000 Mbps Ethernet PoE+ ports with 4 x 1/10Gig SFP+ ports ,1 x RJ45 port console port ,Switching Capacity 128 Gbps , Throughput 96 Mpps ,MAC Address 16k , Switch should support IEEE 802.3af (15.4W) & IEEE 802.3at (30W). Total PoE power: 370W or above , Switch should support DHCP server/relay/client, DHCP snooping/option82 , Switch should support Console, Telnet, SSH v1/2, HTTP, HTTPS, SNMP v1/v2/v3, RMON , TFTP, FTP, SFTP, NTP, ZTP, SPAN, RSPAN,Switch should support support ICMPv6, DHCPv6, ACLv6 ,IPV6 Telnet ,Temperature 0°C -50°C ,Power Supply AC: 100-240V. Make: Digisol/ Cisco/ HP/ Netgear
369	SITC of 1G-LX/LH SFP transceiver module,SMF, 1310nm, 9/125 um Single mode Fiber Type up to 20 KM. Make: Cisco/ Digisol/ Netgear
370	SITC of 40G Ethernet Routing Switch having 8 x 10/100/1000Base-T (RJ45) + 24 x 10GbE (SFP+) + 2 x 40GbE(QSFP+), 1 x RJ45 Ethernet Management port , 1x Console port ,1x USB2.0 interface , Switching Capacity 656Gbps , Throughput 488Mpps , MAC Address 32K ,Routing Table 16K ,Jumbo Frame 10k , Switch Supports Standard and Expanded ACL Based on source/destination IP or MAC, IP Protocol, TCP/UDP port, DSCP, ToS, IP Precedence), VLAN, Tag/Untag, CoS ,MLDv1/v2, PIM-SM/DM for IPv6, IPv6 Any Cast RP, IPv6 ACL, IPv6 QoS ,Switch have CLI, WEB, Telnet, SNMPv1/v2c/v3 through IPv4 and IPv6 ,Switch Supports VSF(Virtual Switch Framework) , Temperature Working 0°C~50°C, storage -40°C~70°C , Power Supply AC: 100~240VAC, 50~60Hz ,+ 48VDC. Make: Digisol, Cisco, HP, Netgear
371	Supply and installation of Dual band 802.11ax WiFi6 Dual Band Access Point. Complying PoE+ for power, with inbuilt on premise virtual controller as well cloud based controlling and administration of WiFi systems All hardware should supplied with necessary mounting brackets and IN power cord with 3 years of comprehensive onsite warranty. Make: Cisco/Digisol/Netgear
372	SITC of Gate way Router for 500 users with Built-in UTM firewall provides 5 years subscription for anti-virus, layer 3-7 IDS/IPS, DPI, SSL detection, and more. Built-in VPN router supports 2.5Gbps or 3Gbps to allow easy remote access. 2 x 2.5 Gigabit SFP port and 10 x Gigabit Ethernet ports *3x Fixed WAN. 2.5Gbps Router. 4 x PoE out ports, IEEE802.3af/at, Maximum PoE Wattage: 36W. Make Grandstream, Paloalto, Fortigate
373	Supply Installation & Fixing of AIO Desktop PC having I7 processor,13th generation, 16GB RAM,DDR 5 RAM, 1TB SSD, Full HD 27 inch IPS,QHD Display, Full HD 5mp Camera, pre loaded windows 11 and MS Office, wireless keyboard and mouse Make: Lenovo ideacentre(F0HM00PXIN)
374	BASEMENT VENTILATION:- Supply, delivery, installation, testing & commissioning of VANE AXIAL FANS as per specifications. Fan shall be AMCA Certified (For Sound and Air Performance as well as FEG) direct driven Vane Axial Fan. The fan shall be equipped with Mounting Bracket, Bird Screen & Spring Isolators for the installation of the fans. Motors (Class H) shall be VFD rated suitable for 415+10% volts, 50 cycles, 3 phase AC supply. Fan static pressure shall be as indicated but actual fan static pressure to be checked by HVAC / MEPVendor. Motors shall be of minimum IE2 efficiency. Fan total efficiency should not be less than 75% and FEG should not be less than 70, noise level should not be more than 80 dB(A) @ 3m distance when measured in hemispherical reverberant room conditions. Silencer to be incorporated to achieve desired sound level. The rate is inclusive of Starter panel.Make: Greenheck/Systemair/Elta/Krugger/Nikotra/Airflow. AXIAL FLOW SMOKE EXHAUST FAN FOR(BASEMENT)Fan Dia - 1200 mm , Volume - 21,000 CFM, SP - 20 mm
375	AXIAL FLOW FRESH AIR FAN FOR(LOWER BASEMENT)Fan Dia - 1200 mm , Volume - 21,000 CFM, SP - 20 mm,
376	JET FAN FOR(BASEMENT)350mm Dia Jet Fan
377	Supply, installation, balancing and commissioning of factroy fabricated G.S.S. (Class VIII 180 GSM) rectangular ducting complete with neoprene rubber gaskets, elbow, splitter dampers, vanes, hangers, supports etc as per approved drawings and confirming to SMACNA standard of following sheet thickness complete as required.Make:Sail/Jindal/Tata. 22 SWG
378	Supply, fabrication, installation and testing the flexible Canvas connections constructed of fire resistance flexible double canvas sleeve at Duct mouth.
379	Supply, delivery, installation, testing & commissioning of Angle Support 50506 MS Angle and MS C Channels
380	Supply, delivery, installation, testing & commissioning of Vibration Pad
381	Supply, delivery, installation, testing & commissioning of bird screen for Fans.
382	Supply, delivery, installation, testing & commissioning of CO Sensor.Make-Dwyer/Schneider/Honeywell
383	Supply, delivery, installation, testing & commissioning of CFD Analysis
384	TOILET VENTILATION & LIFT PRESSURIZATION-Supply, Installation, Testing and Commissioning of Duct mounted Single skinned Circular Inline Centrifugal Fan for Toilet Ventilation with direct driven Backward-curved impellers.The Fan has external rotor motor suitable for 1~, 230V, 50 Hz power supply in complete as per the direction of Engineer-in-charge. MAKE - SYSTEMAIR/ GREENHECK/ ELTA 2250 CFM Cabinet Type Inline Fan with 10 mm SP
385	2500 CFM Cabinet Type Inline Fan with 10 mm SP
386	2750 CFM Cabinet Type Inline Fan with 10 mm SP
387	3000 CFM Cabinet Type Inline Fan with 10 mm SP
388	3200 CFM Cabinet Type Inline Fan with 10 mm SP
389	3500 CFM Cabinet Type Inline Fan with 10 mm SP
390	250 CFM Circular Inline Fan with 6 mm SP
391	350 CFM Circular Inline Fan with 6 mm SP
392	Supply, Installing, Testing and Commissioning of VANE AXIAL FANS as per specifications stated below. Fan shall be direct driven Vane axial fan , IP55, AMCA Certified (For Air and Sound Performance as well as FEG). The fan shall be equipped with mounting bracket, inlet guard (If required) & spring isolators for the installation of the fans. Motors shall be VFD Compatible suitable for 415+10% volts, 50 cycles, 3 phase AC supply. Fan static pressure shall be as indicated but actual fan static pressure to be checked by HVAC / MEP Vendor. Supply Fans shall be activated from fire signal from fire alarm system. Fan shall be with fire proof flexible connection at outlet. Motors shall be of minimum IE2 efficiency, class F insulator. Fan total efficiency should not be less than 72% and FEG should not be less than 85, noise level should not be more than 84 dB(A) @ 3m distance when measured in hemispherical reverberant room conditions. Sound attenutors of appropriate length shall be included in the cost to achieve the desired result.The rate is inclusive of starter panel. MAKE - SYSTEMAIR/ GREENHECK/ ELTALIFT WELL PRESSURIZATION 11,000 CFM, SP -30 mmwc.
393	LIFT LOBBY PRESSURIZATION 25,000 CFM, SP -30 mmwc.
394	Supply, fabrication, installation and testing the flexible Canvas connections constructed of fire resistance flexible double canvas sleeve at Duct mouth as per the direction of Engineer-in-charge.
395	Supply, installation, balancing and commissioning of factroy fabricated G.S.S. (Class VIII 180 GSM) rectangular ducting complete with neoprene rubber gaskets, elbow, splitter dampers, vanes, hangers, supports etc as per approved drawings and confirming to SMACNA standard of following sheet thickness complete as required as per the direction of Engineer-in-charge.Make:Sail/Jindal/Tata. 24 G
396	Supply, installation, testing and balancing of powder coated Extruded Aluminium Grilles without volume control dampers as per the direction of Engineer-in-charge.Make-Glenstorm/Airflow/Systemaire
397	Supply, installation, testing and commissioning of G.I volume control dampers as per the direction of Engineer-in-charge. Make-Glenstorm/Airflow/Systemaire
398	Supply, installation, testing and balancing of External louvers with bird screen as per the direction of Engineer-in-charge.
399	Supplying & fixing of duct dampers in supply air duct as per approved drawings and specifications. Damper shall be with 16G GSS body and blades as per the direction of Engineer-in-charge.
400	Supplying, Fixing, testing and commissioning of fire dampers of minimum 90 minutes fire rated in supply air duct/main branch and return air path as and where required of required sizes i/c control wiring, the damper shall be motorized and spring return so as to close the damper in the event of power failure automatically and open the same in case of power being restored. The spring return action shall be inbuilt mechanism and not externally mounted. The damper shall also be closed in the event of fire signal and, in confirmation to IS and as per specifications complete etc. as required as per the direction of Engineer-in-charge..(Make: Air Flow/ Systemair/ Dynacraft)a) Fire Dampers
401	b) Actuators (Make:- Belimo/ Siemens/ Danfoss)
402	Supply, installation, testing and commissioning of 250mm Dia Propeller Fans with gravity Louver as per the direction of Engineer-in-charge. MAKE - SYSTEMAIR/ GREENHECK/ ELTA
403	P.H. WORKSupplying all materials, labour, T&P and providing and fixing to wall or ceiling and floor C-PVC pipes conforming to pipe fittings of the following nominal bore with clamps including making good the wall, ceiling and floor all complete as per specification and direction of the Engineer in charge. Ground Floor (20mm dia C-PVC pipe (Ashirbad/Supreme/Astrol/Ori Plast)
404	25mm dia C-PVC pipe (Ashirbad/Supreme/Astrol/Ori Plast)
405	40mm dia C-PVC pipe (Ashirbad/Supreme/Astrol/Ori Plast)
406	50mm dia C-PVC pipe (Ashirbad/Supreme/Astrol/Ori Plast)
407	In 1st Floor (20mm dia C-PVC pipe (Ashirbad/Supreme/Astrol/Ori Plast)
408	25mm dia C-PVC pipe (Ashirbad/Supreme/Astrol/Ori Plast)
409	32mm dia C-PVC pipe (Ashirbad/Supreme/Astrol/Ori Plast)
410	50mm dia C-PVC pipe (Ashirbad/Supreme/Astrol/Ori Plast)
411	In 2nd Floor (20mm dia C-PVC pipe (Ashirbad/Supreme/Astrol/Ori Plast)
412	25mm dia C-PVC pipe (Ashirbad/Supreme/Astrol/Ori Plast)
413	32mm dia C-PVC pipe (Ashirbad/Supreme/Astrol/Ori Plast)
414	50mm dia C-PVC pipe (Ashirbad/Supreme/Astrol/Ori Plast)
415	In 3rd Floor(20mm dia C-PVC pipe (Ashirbad/Supreme/Astrol/Ori Plast)
416	25mm dia C-PVC pipe (Ashirbad/Supreme/Astrol/Ori Plast)
417	40mm dia C-PVC pipe (Ashirbad/Supreme/Astrol/Ori Plast)
418	50mm dia C-PVC pipe (Ashirbad/Supreme/Astrol/Ori Plast)
419	In 4th Floor (40mm dia C-PVC pipe (Ashirbad/Supreme/Astrol/Ori Plast)
420	50mm dia C-PVC pipe (Ashirbad/Supreme/Astrol/Ori Plast)
421	Supplying all materials, labour, T&P and cutting holes through existing brick work including making good the damages in cement mortar (1:4) for taking GI pipes and fittings/ PVC pipes and fittings etc all complete as per PH specification and direction of the Engineer in charge.250mm thick wall in Ground floor
422	In 1st Floor
423	In 2nd Floor
424	In 3rd Floor
425	Supplying all materials, labour, T&P and cutting hole in R.C.C floors, roofs, etc upto 19 cm thick for passing G.I. Pipes / P.V.C pipes and fittings etc and repairing the holes after insertion of pipes etc with cement concrete (1:2:4 ) including finishing complete so as to make it leak proof as per direction of the Engineer in charge. in Ground Floor
426	In 1st Floor
427	In 2nd Floor
428	In 3rd Floor
429	Supplying all materials, labour, T&P and cutting grooves in pucca floors and walls for taking GI/ PVC pipes and making good the damages as per the direction of the Engineer in charge. In Ground Floor
430	In 1st Floor
431	In 2nd floor
432	In 3rd Floor
433	Supplying all materials, labour, T&P and cutting holes through existing brick or laterite masonry wall for taking HCI pipes and fittings including making good the damages etc all complete as per PH specification and direction of the Engineer in charge .250mm to 375mm thick wall in Ground Floor to 4th Floor
434	Supplying all materials, labour, T&P and fitting and fixing brass/CP fittings of the following nominal bore with supply of all jointing materials complete as per specification and direction of the Engineer in charge, (Cera Make/ Jaquar Make/ Plaza Make/Hindwrer Make)15mm dia CP Long Body Bib cock (Con-CHR-107KN Make Jaquar , Hindware,Cera or equivelent)
435	15mm dia CP angle stop cock (FLR-ACR-5053N) Make Jaquar , Hindware,Cera or equivelent
436	20mm dia CP consealed stop cock(Con-CHR-083KN Make Jaquar , Hindware,Cera or equivelent)
437	15mm dia CP two in one bib cock (FLR-ACR-5041N) Make Jaquar , Hindware,Cera or equivelent
438	15mm dia CP Health faucet (Con-ALD-MCH-573 Make Jaquar , Hindware,Cera or equivelent )
439	15mm dia CP extension piece, (Make Jaquar , Hindware,Cera or equivelent)
440	15mm dia CP Pillar cock (Con-CHR-011KN (Make Jaquar , Hindware,Cera or equivelent)
441	25mm dia G.M or Brass F.W valve (Sakti make)
442	40mm dia G.M or Brass F.W valve (Sakti make)
443	125mm dia CP gratings
444	15mm CP revolving shower (Make Jaquar , Hindware,Cera or equivelent) CON-CR-209KN.
445	15mm dia CP auto closing Urinal Flush Valve (PRS-CHR-077 (Make Jaquar , Hindware,Cera or equivelent)
446	50mm dia G.M or Brass F.W valve (Sakti make)
447	15mm dia CP Bib cock (Con-CHR-047KN Make Jaquar , Hindware,Cera or equivelent )
448	15mm dia CP Urinal Flush valve (PRS-ANQ-077 Make Jaquar , Hindware,Cera or equivelent)
449	Supply and installation of Rimless Back To Wall WC With UF Soft Close Slim Seat Cover, Hinges, Fixing Accessories And Accessories Set, Size: 340x560x400mm, P-Trap:180mm ARS-WHT-39955P180UFSM, Make Jaquar , Hindware,Cera or equivelent.
450	Supply and installation of Single Piece Slim Concealed Cistern Body with Installation Kit & “S-Type” drain pipe connection set for Wall Hung WC (without Flush Control Plate) JCS-WHT-2400S, Make Jaquar , Hindware,Cera or equivelent.
451	Half pedestal basin(Jaquar/Hindware)FNS-WHT-40801+FNS-WHT-40305/No.91049+91115, Make Jaquar , Hindware,Cera or equivelent.
452	Angle Valve (Jaquar-OPP-SSF-15053PM) Make Jaquar , Hindware,Cera or equivelent
453	Supply and installation of Hand Shower (Health Faucet) with 8mm Dia, 1 Meter Long Flexible Tube & Wall Hook. (ALD-CHR-573) Make Jaquar , Hindware,Cera or equivelent.
454	15mm dia CP Pillar cock (Con-CHR-011KN Make Jaquar , Hindware,Cera or equivelent.)
455	15mm dia CP two in one bib cock (FLR-ACR-5041N) Make Jaquar , Hindware,Cera or equivelent.)
456	Liquid Soap Dispencer (Jaquar-SDR-BLC-DJ0160ASN) Make Jaquar , Hindware,Cera or equivelent
457	Supplying all materials, labour, T&P and fitting and fixing 12.50 litres/10 litres capacity low level flushing cistern with a pair of cast iron or M.S brackets complete with fittings such as siphonic arrangements 15mm nominal size brass/pvc ball valve with polythene float CP brass handle, unions and couplings for connection with inlet, outlet and overflow pipes,32mm dia CP flush bend,15mm dia pvc inlet connection pipe including cutting holes and making good the same and connecting the flush bend with cistern and closet and connecting the inlet pipe with supply main etc all complete as per specification and direction of the Engineer in charge(Cera Make/ Jaquar Make/ Plaza Make/Hindwrer Make) 10 litres PVC L.L. Cistern (Slimline-white)
458	Supplying all materials, labour, T&P and fitting and fixing U-PVC SWR soil waste ventilating pipes and fittings of the following outside diameter conforming to ISI No. 13592/1992 to walls with nails, bobbins and wooden plugs or laying in trenches including jointing with supply of approved rubber lubricant by non-heat application method/as per manufacturer’s specification, testing, earthwork in excavation in all kinds of soil and refilling of trenches as per specification and direction of the Engineer in charge.110mm dia U-PVC SWR pipe(Ori Plast/Finolex/Supreme Make Type-B)
459	110mm U-PVC door Tee(Ori Plast/Finolex/Supreme Make)
460	110mm U-PVC Plain Tee(Ori Plast/Finolex/Supreme Make)
461	110mm U-PVC door bend(Ori Plast/Finolex/Supreme Make)
462	110mm U-PVC plain bend(Ori Plast/Finolex/Supreme Make)
463	110mm dia U-PVC Offset without ear(Ori Plast/Finolex/Supreme Make)
464	110mm U-PVC 'P' trap(Ori Plast/Finolex/Supreme Make)
465	110mm U-PVC cowl(Ori Plast/Finolex/Supreme Make)
466	110mm dia U-PVC Plain Shoe Bend(Ori Plast/Finolex/Supreme Make)
467	110mm dia U-PVC Socket plain(Ori Plast/Finolex/Supreme Make)
468	110mm dia U-PVC Cross Tee with door(Ori Plast/Finolex/Supreme Make)
469	75mm dia U-PVC SWR pipe(Ori Plast/Finolex/Supreme Make Type-B)
470	75mm U-PVC door bend(Ori Plast/Finolex/Supreme Make)
471	75mm U-PVC plain bend(Ori Plast/Finolex/Supreme Make)
472	110mm U-PVC Clamp(Ori Plast/Finolex/Supreme Make)
473	Supplying all materials, labour, T&P and fixing vitreous china water closet, squatting pan (Indian type W.C pan/Orissa pattern squatting pan conforming to IS:2556-part-3-2004) duly embedded in cement concrete (1:5:10) using 4cm size hard granite metal including fixing a pair of vitreous china 250mm x 130mm x 30mm footrest, fixing 100mm dia HCI ‘P’ or ‘S’ trap (with/without 50mm dia horn) for water closet squatting pan including jointing the trap with pan in cement mortar (1:1), cutting the floor and mending good the damages etc all complete as per specification and direction of the Engineer in charge(Cera Make/ Jaquar Make/ Plaza Make/Hindwrer Make), 580mm size Orissa pan(Essco/Hindware/Cera)
474	Supplying all materials, labour, T&P and fixing bowl pattern urinal including connecting the urinal with waste pipe by means of white lead mixed with chopped hemp etc all complete as per specification and direction of the Engineer in charge.(Cera Make/ Jaquar Make/ Plaza Make/Hindwrer Make) Halfstall Urinal(Jaquar/Cera/Hindware)
475	Supplying all materials, labour, T&P and fixing Wash Down Water Closet (European type W.C pan) with integral ‘S’ or ‘P’ trap to the floor with wooden plug and chromium plated screws including jointing the trap with soil pipe in cement mortar (1:1) etc all complete as per specification and direction of the Engineer in charge.(Cera Make/ Jaquar Make/ Plaza Make/Hindwrer Make) E.W.C. with seat cover (Jaquar/Cera/Hindware)
476	One piece commod(Hindware)ELEMENT Cat No.92084.
477	EWC(Matrix set )(P-18)of make Hindware/Jaquar/Cera or Equivalent
478	Supplying all materials, labour, T&P and fixing wash basins with hole for pillar taps conforming to IS:2556-part-4-2004 with cast iron or M S brackets painted white including cutting holes in walls and making good the damages with supply of wooden plugs, screws and cement etc, fixing pedestal for wash basin recessed at the back for the reception of pipes and fittings, fixing PVC waste pipe of 32mm nominal diameter for wash basin including brass check nut complete, fixing pillar taps capstan head screw down high pressure lettered ‘Hot’ and ‘Cold’ with long screws, shanks and back nuts of 15mm dia nominal bore(Plaza make), fixing 15mm dia PVC inlet connection pipe and making connection with pillar cocks and supply mains for wash basin, fixing 32mm dia CP brass waste(Plaza make), etc all complete as per specification and direction of the Engineer in charge(Cera Make/ Jaquar Make/ Plaza Make/Hindwrer Make) Under Counter basin(560x450)Jaquar-FLS-WHT-5701/Hindware-No.10095, make Hindware/Jaquar/Cera.
479	Supplying all materials, labour, T&P and fixing mirror of superior glass conforming to IS:3438-1996 mounted on 6mm thick A.C sheet or plywood sheet and fixed to wooden plugs with CP screws and washers complete as per specification an direction of the Engineer in charge, 600mm x 450mm size B.E mirror
480	Large size mirror with frame(70x0.90x0.90) 47x0.60x0.90=
481	Design mirror( make Hindware/Jaquar/Cera.)
482	Supplying all materials, labour, T&P and fixing standard sized glass-shelf with CP brass brackets and guard rails complete fixed to wooden plugs with CP screws as per specification and direction of the Engineer in charge. 600 x 125mm plate glass shelf with CP guard rails(Jaquar)ACN-CHR-1171N , Make Hindware/Jaquar/Cera.
483	Supplying all materials, labour, T&P and fixing standard sized CP towel rail complete with CP brass brackets fixed to wooden plugs with CP screws as per specification and direction of the Engineer in charge. 25mm x 600mm long CP towel rail ACN-ACR-1111SM Make Hindware/Jaquar/Cera.
484	CP towel Ring(Jaquar)ACN-ACR-1121N . Make Hindware/Jaquar/Cera.
485	Supplying all materials, labour, T&P and fixing CP soap holder complete with CP brass brackets fixed to wooden plugs with CP screws as per specification and direction of the Engineer in charge. CP soap holder (Jaquar)ACN-ACR-1131N Make Hindware/Jaquar/Cera.
486	SOAP DISPENSER WITH GLASS BOTTLE (Jaquar)ACN-CHR-1135N Make Hindware/Jaquar/Cera.
487	Supplying all materials, labour, T&P and fixing wash kitchen sink/laboratory sink with outlet at end and weir overflow including fitting and fixing a pair of cast iron or MS brackets painted white, fixing 50mm/40mm dia CP brass waste, fixing 50mm/40mm dia PVC waste pipe 910mm long with supply of wooden plugs, screws and cement etc including cutting holes in walls and making good the damages etc all complete as per specification and direction of the Engineer in charge(Cera Make/ Jaquar Make/ Plaza Make/Hindwrer Make) 600 x 450 x 250mm size S/S kitchen sink (Jayana make )
488	Supplying all materials labour T&P and filling in foundation and plinth with sand well watered and rammed including conveyance of all materials to work sitepayment of royalty taxes etc all complete as per direction of Engineer in charge In ground floor
489	Supplying all materials, labour, T&P and providing cement concrete (1:4:8) with 4cm size hard granite metal including watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge In ground floor
490	Supplying all materials, labour, T&P and providing cement concrete (1:2:4) with 12mm size hard granite chips broken including watering, curing, conveyance of all materials to worksite, payment of royality, taxes etc all complete as aper specification and direction of the E.I.C. In Ground Floor
491	In 1st Floor
492	In 2nd Floor
493	In 3rd Floor
494	Supplying all materials, labour, T&P and providing cement flush pointing with C.M (1:3) on brickwork including watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge, In Ground Floor.
495	In Ist Floor
496	In 2nd Floor
497	In 3rd Floor
498	Supplying all materials, labour, T&P and providing 12mm thick cement plaster (1:4) on brickwork including cement punning,watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge.In Ist Floor
499	In 2nd Floor
500	In 3rd Floor

Tender Documents

SR No	FileName	File Description
1	Click here to download tender document	Tender Documents
2	Click here to download tender document	Tender Documents
3	Click here to download tender document	Tender Documents
4	Click here to download tender document	Tender Documents

Also Visit

Tenders

Odisha Tenders

Construction Tenders

Building Construction Tenders

Building Work Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Construction Of Collectorate Building At Sambalpur, Phase-Ii., Sambalpur-Odisha

Tender Documents

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Construction Of Collectorate Building At Sambalpur, Phase-Ii., Sambalpur-Odisha

Tender Documents

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us