|
| 1 | Renovation works |
| 2 | 50.12.4.2:Providing and fixing false ceiling with 7.5 mm thick PVC wooden grains panel board ceiling of approved quality in aluminium frame work with necessary screws etc complete ( aluminium frame work shall be paid separately) |
| 3 | 21.5:Providing and fixing powder coated aluminium work ( minimum thickness of powder coating 50 micron) consisting of tee /angle sections, of approved make conforming to IS : 733 in frames of false ceiling including aluminium angle cleats with necessary C.P brass/ stainless steel sunk screws, aluminium perimeter angles fixed to wall with stainless steel rawl plugs @ 450 mm centre to centre and fixing the frame work to G.I level adjusting hangers 6 mm dia. with necessary cadmium plated machine screws all complete as per approved architectural drawings and direction of the Engineer-in-Charge ( level adjusting hangers, ceiling cleats and expansion hold fasteners to be paid for separately ). |
| 4 | 9.51.2:Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete.With 12 mm mild steel U beading |
| 5 | 2.8.1:Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil |
| 6 | 4.1.8:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 7 | 5.1.2:Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 8 | 5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete |
| 9 | 5.9.6:Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts |
| 10 | 5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more |
| 11 | 10.25.2:Item Shifted to Sub head 14 as item 14.73Item Shifted to head 14 as item 14.74Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 12 | OD433902/2025-2026:Laterite sliced cladding- Providing and fixing laterate cladding with 20mm thick gang saw cut stone with (machine cut edges) of uniform colour and size upto 30cmx15cm as per Architectural drawing and direction of Engineers in-charge. Laterite stone |
| 13 | 13.61.1:Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work |
| 14 | Road work |
| 15 | OD434025/2025-2026:Surface dressing of the ground including removing of the vegetation not exceeding 15 cm deep and disposal debris, lead upto50 m and lift up to 150 m .All kinds of soil. |
| 16 | OD434048/2025-2026:[OD From MORD 4.1.A.1] Granular Sub-base with Well Graded Material (Table 400.1) (A) ByMix in Place Method Construction of granular sub-base by providing well graded material,spreading in uniform layers with motor grader on prepared surface, mixing by mix in placemethod with rotavator at OMC, and compacting with plate vibrator to achieve the desireddensity, complete as per Technical Specification Clause 401. (i) For Grading I Material |
| 17 | OD434026/2025-2026:[OD from MORD 75.8.1] - Providing Plain cement concrete for road work CC 1:2:4 (1 cement:2 fine aggregate: 4course aggregate) laid to required slope and camber in panels as requiredincluding compaction, finishing and tamping etc .complete. Max. size of course aggregate notexceeding 25mm , mixed in concrete mixer etc complete as per specification (i) Nominal mix(1:2:4)(excluding form work) |
| 18 | OD434047/2025-2026:Providing and fixing Granite of any colour and shade for name board of required size laid over base of cement mortar(1 cement: 4 course sand) including all charges etc complete at all levels including lettering and fixing Please Enable Macros to View BoQ information |
