|
| 1 | Maintenance works |
| 2 | OD511779/2025-2026:Labour engaged for cleaning works |
| 3 | 15.7.4:Demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge.In cement mortar |
| 4 | 15.28.2:Dismantling roofing including ridges, hips, velleys and gutters etc., and stacking the material within 50 metres lead of :Asbestos cement Sheet |
| 5 | 15.19:Dismantling steel work manually / by mechanical means in built up sections without dismembering and stacking within 50 metres lead as per directions of Engineer -in-Charge. |
| 6 | 50.2.3.1:Pumping or Bailing out water and removing slush etc by using pump set including cost of labour, oil hire charges of pumpset, etc complete |
| 7 | OD518472/2025-2026:Labour engaged for cleaning well |
| 8 | 2.6.1:Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.All kinds of soil |
| 9 | OD493834/2025-2026:Laterate masonry with departmental laterate stones of size 35x20x20cm or nearest size in cement mortar 1:6 for foundation and basement including all cost of materials, labour charges etc.(Modified DAR code 50.6.7.1) |
| 10 | OD502557/2025-2026:Laterate masonry with neatly dressed laterate stone of size 35x20x20cm or nearest size in cement mortar 1:6 for foundation and basement including all cost of materials, labour charges etc.(Modified DAR code 50.6.7.1) |
| 11 | OD511645/2025-2026:Laterate masonry with neatly dressed laterate stone of size 35x20x20cm or nearest size in cement mortar 1:6 for superstructure above plinth level up to floor two level including all cost of materials, labour charges etc. complete.(Modified DAR code 50.6.7.2) |
| 12 | OD502591/2025-2026:Laterite dry masonry with neatly dressed laterite stones of size 32x20x20cm or nearest size for foundation and basement including all cost of materials, labour charges etc. complete(DAR code 50.6.7.1 modified) |
| 13 | 5.1.3:Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 14 | 5.9.5:Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers |
| 15 | 5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more |
| 16 | 4.1.3:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-III)derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 17 | 11.37:Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete |
| 18 | 15.23.2:Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.For thickness of tiles above 25 mm and up to 40 mm |
| 19 | OD519946/2025-2026:Providing and laying departmental factory made chamfered edge cement concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking, etc. of required strength,thickness, size and shape made by table vibratory method using PU mould, laid in required colour and pattern over 50mm thick compacted bed of 6mm broken stone aggregate, compacting and proper embedding, laying of interlocking paver blocks into the broken stone bedding layer through the vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping with extra sand, completing all as per the direction of Engineer in charge. 80mm thick CC paver block of M-30 grade with approved colour design and pattern. (DAR Code 16.91.2 modified) |
| 20 | OD518526/2025-2026:Providing and laying factory made chamfered edge cement concrete paver blocks(60mm thick,M-30) in footpath, parks, lawns, drive ways or light traffic parking, etc. of required strength,thickness, size and shape made by table vibratory method using PU mould, laid in required colour and pattern over 50mm thick compacted bed of 6mm broken stone aggregate, compacting and proper embedding, laying of interlocking paver blocks into the broken stone bedding layer through the vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping with extra sand, completing all as per the direction of Engineer in charge. 80mm thick CC paver block of M-30 grade with approved colour design and pattern. (DAR Code 16.91.2 modified) |
| 21 | 50.10.2:Steel work for purlin/single section with G I pipes including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete |
| 22 | OD514537/2025-2026:Providing Aluminium Composite Panel Cladding with open grooves for linear as well as curvilinear portions, for small heights and all levels etc. including providing,fabricating,supplying and fixing panels of Aluminium Composite Panel Cladding in pan shape in metallic colour of approved shades made out of 4mm thick Aluminium Composite Panel material consisting of 3mm thick FR grade mineral core sandwiched between two aluminium sheets(each 0.50mm thick).The aluminium composite panel cladding sheet shall be coil coated with Kynar 500 based PVDF/Lumiflon based fluoropolymer resin coating of approved colour and shade on face 1 and polymer(Service) coating on face 2 as specified using stainless steel screws,nuts,bolts,washers,cleats,weather silicone sealant,backer rods etc.Base framework for ACP cladding is payable under the relevant aluminium items.The contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete, as per the architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge.However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminium Composite Panel Cladding(including width of groove)shall be measured in sqm. upto two decimal places(DAR code 25.7 modified) |
| 23 | OD505203/2025-2026:Providing and fixing Alu Zinc profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.40 mm (+0.05%), thickness . Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length up to 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete up to any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. (DAR code 12.50 modified) |
| 24 | OD506200/2025-2026:Providing and fixing 150mm square or round half cut PVC pipe over flat iron brackets of 20x5 mm size including all costs of materials,labour charges etc. complete. |
| 25 | 50.18.9.18.2:Providing and fixing PVC pipes including fixing the pipe with clamps/Clips at 1.00 m spacing. This included jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 75 mm dia 4 Kfg/cm2 - External work - Exposed on wall |
| 26 | 50.18.9.14.2:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 32 mm dia 6 Kgf/cm2 - External work - Exposed on wall |
| 27 | 50.18.9.21.4:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75 mm dia Bend |
| 28 | 50.18.9.8.2:Providing and fixing PVC pipes includings of pipes with one step PVC solvent cement, trenching and refilling & testing of joints complete as per direction of Engineer in Charge. 75 mm dia 4 Kgf/cm2 |
| 29 | 18.54.3:Providing and fixing PTMT bib cock of approved quality and colour.15 mm nominal bore, 165 mm long, weighing not less than 110 gms |
| 30 | 17.7.4:Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap |
| 31 | 13.1.2:12 mm cement plaster of mix:1:6 (1 cement : 6 fine sand). |
| 32 | 13.33.1:Pointing on stone work with cement mortar 1:3 ( 1 cement : 3 fine sand):Flush/ Ruled pointing |
| 33 | 13.48.1:Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as per manufacturers specifications:Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of special primer applied @ 0.75 ltr /10 sqm |
| 34 | 13.99.1:Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :One or more coats on old work Please Enable Macros to View BoQ information |
