Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains of soil such as pick work, jumper work, pick jumper work, blasting work, jumper blasting work, soft and hard blasting and saturated soil, de-watering, including wedging out rocks where blasting work is prohibited, chiseling or any other mixed variety of soil, including shoring, strutting or bailing out water upto any depth or any height quantum of water including de-watering removal of slush and stacking the serviceable and un-serviceable material clear from the edge of excavation as per direction of Engineer-in-Charge and returning the stacked soil in 15cm (Fifteen centimeter) layers, when required into plinths, sides of foundation etcetera consolidating each deposited layer by ramming, watering and then disposing of all excavated earth including carriage of material within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-Incharge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 2 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete including carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 3 | Stone filling in plinth with approved quality under floor including watering, ramming, consolidating and dressing complete including carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 4 | Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights/depth of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in Foundation footings, bases of columns and mass concrete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design, entire satisfaction and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 5 | Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights/depth of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in flat surfaces such as soffits of suspended floors roofs, landings including curved surfaces where ever required as per Architectural drawing, design and specifications and the like floor etcetera including carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 6 | Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in beams cantilevers girders lintels window sills, cornices, arches corbelling including curved surfaces where ever required sides and soffits of beams haunchings cantilevers bressumers and lintels upto all depths including carriage of material within all leads, lifts and other incidentals as per approved drawing, design, specifications, entire satisfaction and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 7 | Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in columns pillar posts and struts square rectangular polygonal in plan including mouldings, cornices etcetera complete as per Architectural drawing, design and specifications including carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 8 | Providing form work with steel plates of 3.15mm (Three decimal fifteen millimetres) thick, welded with angle iron in frames of 30x30x5mm(Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights and removal of the same for in-situ reinforced concrete and plain concrete work in vertical surface such as walls (any thickness) partitions and the like including attached, pilasters, buttresses, plinth and string courses and the like including carriage of material within all leads, lifts and other incidentals as per approved drawing, design, specifications and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 9 | Providing form work with steel plates of 3.15mm (Three decimal fifteen millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights and removal of the same for in-situ reinforced concrete and plain concrete work in Edges of slab and breaks in floors and walls under any thickness including carriage of material within all leads, lifts and other incidentals as per approved drawing, design, specifications and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 10 | Providing form work with steel plates 3.15mm (Three point one five millimeters) thick, welded with angle iron in frame 30x30x5mm (Thirty into Thirty into Five millimeters) so as to give a fair finish including centering, shuttering strutting and propping etc, with wooden battens and ballies, height of propping and centering in all heights. below supporting floor to ceiling and removal of the same for in situ reinforced concrete and plain concrete work In plain concrete work in window sill, cornice and moulding and curing complete, excluding the cost of reinforcement complete, as per HPPWD specifications or as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Malkhana, Royality, Octroi, toll tax or any taxes imposed by the Government. |
| 11 | Providing and laying in position cement concrete 1:4:8 (One cement isto four coarse sand isto eight graded stone aggregate 20mm (Twenty millimetre) nominal size mechanically mixed and vibrated of specified grade excluding the cost of centering and shuttering, All work up to all floor level including carriage of materials in all leads and lift as per direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 12 | Providing and laying in position machine batched and machine mixed cement concrete work of grade M-20 (M-Twenty) design mix to obtain the minimum compressive strength of 20N/mm2 (Twenty niewton per square millimetre) with cement contents not less than @ 330 kg/cum (at the rate Three hundred thirty kilogram per cubic metre) or as per approved design mix. All works upto plinth level to give a smooth surfaces machanically mixed and vibrated including curing complete and pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability etcetera including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 13 | Providing and laying in position machine batched and machine mixed cement concrete work of grade M-20 (M-Twenty) design mix to obtain the minimum compressive strength of 20N/mm2 (Twenty niewton per square millimetre) with cement contents not less than @ 330 kg/cum (at the rate Three hundred thirty kilogram per cubic metre) or as per approved design mix. All works above plinth level upto all floor level to give a smooth surfaces machanically mixed and vibrated including curing complete and pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability etcetera including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 14 | Providing tor steel reinforcement of Tata/Sail for Reinforced Cement Concrete work including straightening, cutting, bending, placing in position and binding all complete upto all floor level Thermo-Mechanically Treated bars of grade Fe-500D or more etcetera complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 15 | Providing and laying damp proof course 50mm (Fifteen millimeters) thick with cement concrete 1:2:4 (one cement isto two sand isto four graded crushed stone aggregate 12.5mm (Twelve decimal five millimeter) nominal size) and curing complete including cost of form work as required at site or as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental. The rate inclusive of Royality, Malkhana, Octroi, Toll Tax Sales tax,GST or any other taxes imposed by the Government. |
| 16 | Applying a coat of hot bitumen (mexphalt 80/100 (eighty/hundred) or equivalent) using 1.70 Kgs. (one decimal seven zero kilogramme) per square meter on damp proof course after cleaning the surface with a piece of cloth lightly soaked in kerosene oil complete including carriage of materials within all leads, lifts and other incidental and as per the direction of Engineer-in-Charge. The rate inclusive of Malkhana, Octroi, Toll Tax Sales tax, GST or any other taxes imposed by the Government. |
| 17 | Coursed rubble masonary crushed with hard stone of approved quality in foundition and plinth in wall in cement mortar 1:6 Cement mortar 1:6 (One cement isto six coarse sand) complete as per HPPWD specifications or as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate inclusive of Royality, Malkhana, Octroi, GST, Toll Tax Sales tax or any other taxes imposed by the Government. |
| 18 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level Cement mortar 1:4 (One cement isto Four coarse sand) complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government. |
| 19 | Second Class Brick work using common burnt clay building bricks in Super structure above plinth level upto all floor levels in cement mortar 1:6 (one cement isto six sand) and curing complete as per approved drawing, design, specification and as per direction and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 20 | Second class half brick work using common burnt clay building bricks in super-structure above plinth level upto all floor level in heights/floor level in cement mortar 1:4 (one cement isto four sand) shall be provided with hoop iron and curing complete including carriage of materials within all leads, lifts and other incidental, or as directed by the Engineer-in-Charge. The rate including Royality, Malkhana, Octroi, GST, Toll Tax Sales tax or any other taxes imposed by the Government. |
| 21 | Providing and fixing coloured anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868. Minimum anodic coating of grade AC 15) sub frame work for door,windows and ventilators of section no 14081, 4524 & 4526 of Jindal / Hindalco with extruded built up standard tubular sectionsr fixed with dash fastener of required dia and size (Dash fastener to be paid for separately). As per specificatin, Drawing and Direction by the Engineer-in-Charge. The rate including Royality, Malkhana, Octroi, GST, Toll Tax Sales tax or any other taxes imposed by the Government. |
| 22 | Providing and fixing coloured coated/ anodised aluminium work for shutters of doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of Jindal /Hindalco approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etcetera Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-incharge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) complete as per architectural drawings specifications, design and as per the directions of Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 23 | Providing and fixing factory made PVC door frame single rebate of any colours of size 50x47mm (Fifty into forty seven millimetre) with a wall thickness of 5mm (five millimetre) made out of extruded 5mm (five millimetre) rigid PVC foam sheet heat bend & mitred at corners and jointed with 2 (Two) Nos. of 150mm (One hundered fifty millimetre) long brackets of 15x15mm (Fifteen into fifteen millimetre) M.S. square tube, the vertical door profiles to be reinforced with 19x19mm (Nineteen into nineteen millimetre) M.S. square tube of 19 (Nineteen) gauge EPDM rubber gasket weather seal to be provided throughout the frame includingfixing of door frame to wall with M.S. screws 100 (One hundered) long with wooden or rawl plugs emedded in masonry complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 24 | Providing and fixing to existing door frames 30mm (Thirty millimetre) thick factory made Prelaminated PVC door shutter consisting of frame made out of M.S. tubes of 19 (Nineteen) gauge thickness and size of 19x19mm (Nineteen into nineteen millimetre) for styles and 15x15mm (Fifteen into fifteen millimetre) for top & bottom rails, (Code no 9.120 ) of Rajshri M.S. frame shall have a coat of steel primers of approved make and manufacture M.S. frame covered with 5mm thick heat moulded PVC \\"C\\" channel of size 30mm (Thirty millimetre) thickness, 70mm (Seventy millimetre) width out of which 50mm (Fifty millimetre) shall be flat and 20mm (Twenty millimetre) shall be tappred in 45 (Forty five) degree angle on either side forming style and 5mm (Five millimetre) thick, 95mm (Ninety five millimetre) wide, PVC sheet out of which 75mm shall be flat and 20mm (Twenty millimetre) shall be tapered in 45o (Forty five degree) on the inner side to form top and bottom rail and 115mm (One hundered fifteen millimetre) wide PVC sheet out of which 75mm (Seventy five millmetre) shall be flat and 20mm (Twenty millimetre) shall be tapered on both side to form lock rail, top, bottom and lock rail shall be provided either side of the panel 10mm (Ten millimetre) thick, 20mm (Twenty millimetre) wide cross PVC sheet be provided as gap insert for top rail and bottom rail paneling of 5mm thick both side PVC Sheet to be fitted in the M.S. frame welded/sealed to the style & rails, joints mitred and jointed with solvent cement adhesive includingfixing of PVC shutter with existing frame with M.S. butt hinges 100x50x1.90mm (One hundered into fifty into One point nine zero millimetre) size with necessary screws etcetera complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 25 | Providing and fixing fly proof stainless steel wire mesh shutters having stainless steel 32 gauge fly mesh of 304 grade with 144 holes per square inch of 0.5mm (Zero point five millimetre) dia wire and 1.4mm (One point four millimetre) aperture on both sides in existing steel shutters complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 26 | Providing and fixing 8mm (Eight millimetre) thick anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200mm (Two hundred millimetre) centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-Charge, including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 27 | Providing and fixing 12mm (Twenty five millimetre) thick prelaminated MDF board /Phenol bonded BWP grade particle board pf green ply (exterior grade) approved shade Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side complete as per requirement and direction of Engineer-in-Charge, including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 28 | Providing and fixing 12mm (Twenty five millimetre) thick prelaminated MDF board/ Phenol bonded BWP grade particle board pf green ply, thein side of shutter shall have covering of aluminum sheet of approved shade as per specification, approved drawing, design, etc complete as per requirement and direction of Engineer-in-Charge, including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 29 | Providing and fixing 6mm (Six millimetre) thickness (weight not less than 15.00kg/sqm) Glass panes of Modi Guard/Saint Gobain/ AIS/Atul /Gold Plus in door,window, ventilator shutters and partitions etcetera with EPDM rubber /neoprene gasket etcetera complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 30 | Providing and fixing 5mm (Five millimetre) thickness (weight not less than 12.50kg/sqm) Glass panes of Modi Guard/Saint Gobain/ AIS/Atul /Gold Plus glazing in aluminium door, window, ventilator shutters and partitions etcetera with EPDM rubber /neoprene gasket etcetera complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 31 | Providing and fixing 4mm (Four millimetre) thickness (weight not less than 10.00kg/sqm) Glass panes of Modi Guard/Saint Gobain/ AIS/Atul /Gold Plus glazing in door,window, ventilator shutters and partitions etcetera with EPDM rubber /neoprene gasket etcetera complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 32 | Providing and fixing 19mm (Nineteen millimetres) thick water proof Termite resistant commercial board for cup board shutters including 19mm (Nineteen millimetres) thick shelve sand back side of the cub board shall be of 6mm thick ply of Euro/green ply and all cut portions of shutter shall have 6mm/12mm thick hard wood edging. The shutter from out side shall to be finished with 1mm thick lamination of approved shade including fixing Top PTMT handles 125mm long shall be provided in wood colour with nickel plated piano hinges including fixing with nickel plated piano hinges with screws etcetera. (Area forPayment shall be measured for front faceonly) and as per specifications , approved Drawing and design complete as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government. |
| 33 | Providing and fixing cup-board shutter magnic catcher with necessary screws etcetera complete as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government. |
| 34 | Providing and fixing 65x35mm (Sixty five into Thirty five millimetres) special quality bright finished brass cup-board locks or ward robe locks with six levers including necessary screws etcetra complete (Indian make of approved quality) as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government. |
| 35 | Providing and fixing Stainless Steel curtain rail with rollers stop ends and brackets in pelmets with curtain rod 25mm (Twenty five millimetre) dia and brackets complete as per the entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government. |
| 36 | Providing and fixing 300x16 mm (Three hundred into sixteen millimeters) aluminum Matt finished sliding door bolts, make of PILOT/Sheel or equivalent anodized transparent or dyed to required colour and shade with necessary bolts, nuts and screws etcetera complete as per HPPWD specifications and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Octroi, Toll tax, GST or any taxes imposed by the Government. |
| 37 | Providing and fixing 250x16 mm (Two hundred fifty into sixteen millimeters) aluminum Matt finished sliding door bolts, make of PILOT/Sheel or equivalent anodized transparent or dyed to required colour and shade with necessary bolts, nuts and screws etcetera complete as per HPPWD specifications and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Octroi, Toll tax, GST or any taxes imposed by the Government. |
| 38 | Providing and fixing 250x10mm (Two hundred fifty into ten millimeters) aluminum Matt finished tower bolts (Barrel type) make of pilot/sheel or equivalent anodized transparent or dyed to required colour and shade with screws etcetera complete as per HPPWD specifications and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Octroi, Toll tax, GST or any taxes imposed by the Government. |
| 39 | Providing and fixing 150x10mm (One hundred fifty into ten millimeters) aluminum Matt finished tower bolts (Barrel type) make of pilot/sheel or equivalent anodized transparent or dyed to required colour and shade with screws etcetera complete as per HPPWD specifications and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Octroi, Toll tax, GST or any taxes imposed by the Government. |
| 40 | Providing and fixing 150mm (One hundred fifty millimeters) aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etcetera complete as per HPPWD specifications and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Malkhana, Octroi, Toll tax, GST or any other taxes imposed by the Government. |
| 41 | Providing and fixing 125mm (one hundred twenty five millimeters) aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etcetera complete as per HPPWD specifications and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Malkhana, Octroi, Toll tax, GST or any other taxes imposed by the Government. |
| 42 | Providing and fixing Aluminum oxidized PILOT/ Sheel or equivalant oxidized 250mm (Two hundred fifty millimetre) size hooks and eyes complete as per HPPWD specifications and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Malkhana, Octroi, Toll tax, GST or any other taxes imposed by the Government. |
| 43 | Providing and fixing Aluminum oxidized Hydraulical door closer complete as per HPPWD specifications and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Malkhana, Octroi, Toll tax, GST or any other taxes imposed by the Government. |
| 44 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC10 as per IS:1868) transparent or dyed to required colour and shade, with necessary screws etcetera complete Twin rubber stoppe as per HPPWD specifications and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Malkhana, Octroi, Toll tax, GST or any other taxes imposed by the Government. |
| 45 | Providing and laying 19mm (Nineteen millimetre) thick Mirror polished Kota stone slab 55x55cm (fifty five into fifty five centimetre) mirror polished with 7.5cm (seven point five centimetre) wide Jaislmer yellow band in flooring laid over 20mm (twenty millimetre) thick base of cement mortar 1:4 (one cement isto four sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing nosing and moulding complete upto all floor levels as per HPPWD specifications approved drawig, design or as directed by the Engineer-in-Charge, including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of Malkhana, Royality, Octroi, GST, toll tax, sale tax or any other taxes imposed by the Government. |
| 46 | Providing and laying 600x600x10mm (Six hundered into six hundered into ten millimetre) Double Charge / Ultra Charge vetrified tiles of Restile /Nitco /Rak /Kajaria /Orient -Bell /AGL/ Simpolo /Johnson / Somany of approved shade and design, in flooring laid on a bed of 20mm (twenty millimetre) thick cement mortar 1:4 (One cement isto four sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 47 | Providing and laying 300x300 mm (Three hundered into three hundered millimetres) Full body Matt finish Vitrified tiles of Restile/Nitco/Rak/Kajaria (Eternity)/Orient-Bell/AGL/Simpolo/Johnson/Somany of approved shade and design, in flooring etcetera laid on a bed of 20mm (twenty millimetre) thick cement mortar 1:4 (One cement isto four sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 48 | Providing and laying 40mm (Forty millimeter) thick cement concrete flooring 1:2:4 (One cement isto two sand isto four graded stone aggregate 20mm (Twenty millimetre) nominal size) laid one layer finished with a floating coat of neat cement including preparation of surface grading complete and as per direction and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 49 | Providing and fixing 20mm (Twenty millimeters) thick Kota stone slabs in risers of steps, skirting, dado and pillars laid on 12mm (Twelve millimetre) (average) thick cement mortar 1:3 (One cement isto three coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete as per HPPWD specifications and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Malkhana, Octroi, Toll tax, GST or any other taxes imposed by the Government. |
| 50 | Providing and laying Double Charge /Ultra Charge Vitrified tiles of Restile/Johnson/ Nitco/Kajaria/AGL/ Simpolo /Somany /Orient & Bell as per approved shade and design of the office Size of Tile 600x600 mm (Six hundered into six hundered millimetre) size (thickness to be specified by manufacturer), with water absorption less than 0.08% (Zero point zero eight percent) and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12mm (Twelve millimetre) thick bed of cement mortar 1:3 (One cement isto Three coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm (Three point three kilogram per suare metre) including grouting the joint with white cement & matching pigments etcetera complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 51 | Providing and laying 300x450mm (Three hundred into four hundred fifty millimetre) white glazed tile/ glazed tiles of Restile/ Nitco/Kajaria/AGL/Simpolo/Somany /Johnson as per approved shade and design of the office (thickness to be specified by the manufacturer) in skirting, riser and steps with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:3 (One cement isto three coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etcetera, complete as per HPPWD specifications and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Malkhana, Octroi, Toll tax, GST or any other taxes imposed by the Government. |
| 52 | Providing and fixing 19mm (Nineteen millimetre) thick Baroda green marble slab having semi round nosing gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20mm (Twenty millimetre) thick base cement mortar 1:4 (One cement isto four coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etcetera complete as per HPPWD specifications and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Malkhana, Octroi, Toll tax, GST or any other taxes imposed by the Government. |
| 53 | Providing and laying 25mm (Twenty five millimetre) thick Kota Stone in single piece in M.S. stair case over M.S. L section as per approved drawing, design and specifications complete and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Malkhana, Octroi, Toll tax, GST or any other taxes imposed by the Government. |
| 54 | Providing and laying 40mm thick fine dressed red sand stone flooring over 20mm (Twenty millimetre) (average) thick base of cement mortar 1:5 (One cement isto five coarse sand), including pointing with cement mortar 1:2 (One cement isto two stone dust) with an admixture of pigment to match the shade of stone complete and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Malkhana, Octroi, Toll tax, GST or any other taxes imposed by the Government. |
| 55 | Providing and fixing 50mm (Fifty millimetre) dia M.S. Pipe hand rail slip resistant with round end sat two level ie 75cm (Seventy five centimetre) and 90cm (Ninety centimetre) height. It should extend 30cm beyond the top and bottom of the ramp welded with 25mm (Twenty five millimetre) dia metre M.S hollow pipe balusters embedded in cement concrete 60cm (Sixty centimetre) centre to centre and jointing with electrical gas welding at top alongwith hand rail of hollow M.S. pipe of 50mm (Fifteen millimetre) diametre as per approved drawing, design and specifications complete and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Malkhana, Octroi, Toll tax, GST or any other taxes imposed by the Government. |
| 56 | Providing and fixing staircase railing having Readymade M.S. Hollow pipe (D-section) 75x40mm dia (Seventy five into forty millimetre) diametre hand rail with M.S. flat as per detail and baluster of 19mmx19mm (ninetten into nineteen millimetre) M.S solid square bars with a clear height of 85cm (eighty five centimetre) at 328 cm c/c (thirty centimetre centre to centre) jonting in cement concrete steps. The vertical balusters to be welded jonted with M.S hollow hand rail and applying a coat of red lead paint complete in all respect as per specifications approved drawing, design and as directed by the Engineer-in-Chagre. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 57 | Providing and fixing factory made ridges or hips having proper gola shape 60cm (Sixty millimetre) overall with 0.60mm (Zero point six zero millimetre) thick prepainted steel sheets in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating of Tata / Sail / Reliance / Jindals steels i/c fixing with prepainted iron J or L hooks, bolts & nuts 6mm dia & prepainted G.I. limpet and bitumen washers complete as per approved drawing, design and specifications and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 58 | Providing and fixing 0.60mm (zero point six zero millimetre) thick prepainted steel sheet (IS marked Z-120) of TATA Durashine / Reliance / Jindal Steel over steel trussed in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster (RMP) organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating of back coat of polyster of 5 (Five) microns over 5 (Five) microns primer coating including fixing with prepainted iron J or L hooks,bolts and nuts 6mm (six millimetre) diametres with prepainted limpet, rubber washers complete with all accessories as required as per specification, drawing and design and specifications.and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Malkhana, Octroi, Toll tax, GST or any other taxes imposed by the Government. |
| 59 | Providing and fixing valley 90cm (Ninety centimetres) overall 0.60mm (Zero point sixty millimetres) thick prepainted steel sheet of Tata Durashine /Sail /Reliance /Jindals steels in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of back coat of polyster of 5 (five) microns over 5 (five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (six millimetres) dia with prepainted G.I. limpet and bitumen washers complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 60 | Providing and fixing 30cm (Thirty Centimetre) wide 25cm (Twenty five centimetre) deep 0.60mm (Zero point six zero millimetres) thick prepainted plain P.G.I. sheet gutter of Tata / Sail having dome shape grating fixed with bolts, nuts and washers etcetera including making necessary connections with rain water pipe complete including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 61 | Providing and fixing M.S. B.P. sheet 2.0mm (Two point zero millimetre) thick in eaves board/facia/ soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-charge (Base members of steel work shall be measured and paid separately) including fixing complete as per architectural drawings including carriage of material, within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 62 | Providing and fixing flashing 38cm (Thirty eighty centimetre) overall with 0.60mm (Zero point six zero millimetre) thick prepainted sheet in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia meter & prepainted G.I. limpet & bitumen washers complete as per architectural drawings including carriage of material, within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 63 | Providing water proofing treatment shall be done in two coats apply First coat of Dr. Fixit Torch SHIELD (P-3160-3mm) to the clean and saturated surface maintaining a coverage 0.60 sqm (Zero point six zero square meter) per kilogram to achieve 1mm (one millimeter) thickness this coating shall also be executed upto 300mm vertically. The 2nd coats hall be applied in opposite direction after 4 to 6 (Four to six) hours of application of 1st coat then sprinkle sand on top surface of applied Dr.Fixit Fast flex white still tacky and the second coat.The napply cement mortar 1:4 (one cement isto four sand) and mixed with Pidi proof LW at the rate 200 ml (two hundred millimetre) per 50 (Fifty kilogram) of cement over the floor with suitable gradient towords drain water pipe while the second coat of Dr. Fixit is still tacky. complete as per approved drawing, design including carriage of materials within all leads, lifts and other incidental, and as per directions of Engineer-in-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 64 | Providing and fixing 150mm (One hundered fifty millimetre) on wall face PVC acessories for rain water pipes working pressure 4/6 kg/cm2 (Four/Six kilogram per centimetre sqaure) ISI marked of Finolex / Relpipe (Reliance)/Vectus including priming coat, painting and welding etcetera complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 65 | Providing and fixing 150mm (One hundered fifty millimetre) Plain Bend on wall face PVC acessories for rain water pipes working pressure 4/6 kg/cm2 (Four/Six kilogram per centimetre sqaure) ISI marked of Finolex / Relpipe (Reliance)/Vectus including priming coat, painting and welding etcetera complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 66 | Providing and fixing 150mm (One hundered fifty millimetre) Plain Shoe on wall face PVC acessories for rain water pipes working pressure 4/6 kg/cm2 (Four/Six kilogram per centimetre sqaure) ISI marked of Finolex / Relpipe (Reliance)/Vectus including priming coat, painting and welding etcetera complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 67 | Providing and fixing PVC clamps of approved design to PVC rain water pipe and making good the walls etcetera; as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 68 | Structural steel work of Tata/Sail riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of Octroi, Royality, Malkhana, Toll tax, Sale tax, GST or any other taxes imposed by the Government. |
| 69 | Providing and fixing M.S. channels Frames 75x40x4mm (Seventy five into forty into four millimetre) M.S. angle iron 25x20x3mm (Twenty five into twenty into three millimetre) for doors, windows, frames manufactured from M.S. T-Section 25x25x3mm (Twenty five into twenty five into three millimetre) and Z- Sections with M.S. flat 75mmx4mm (Seventy five millimetre into four millimetre) in combination as per drawing and design including hinges, jamb, lock jamb beed and if required thrashold including thrashold of M.S. angles means lugs, with split and tails to each jamb including iron butt hinges 2.5mm (Two point five millimetre) thick with a provision of locking arrangement and shock observers as specified and applying a coat of approved steel primer after pre-treatment of the surface etcetera including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 70 | Providing, fabricating and erection of Structural steel work of Tata / Sail / Reliance/Jindal riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 71 | Painting two or more coats (excluding priming coat) on new steel and other metal surfaces with enamel paint of approved brand and manufacture enamel (Narolac/Asian paints) other than white and of approved shade brushing to give an even shade including cleaning the surface of all dirt, dust and other foreign matter complete as per HPPWD specifications and as directed by the Engineer-in-Charge, including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of Octroi, GST, Toll Tax Sales tax or any other taxes imposed by the Government. |
| 72 | Painting two or more coats (excluding priming coat) over new wood and wood based surfaces with enamel paint of approved brand and manufacture (Narolac/Asian paints) and of approved shade to give an even shade including cleaning the surface of all dirt, dust and other foreign matter complete as per HPPWD specifications and as directed by the Engineer-in-Charge, including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of Octroi, GST, Toll Tax Sales tax or any other taxes imposed by the Government. |
| 73 | 6mm (Six millimetre) thick cement plaster to ceiling with cement mortar 1:3 (one cement isto three sand), upto all floor level complete as per HPPWD specifications approved drawing, design and as directed by the Engineer-in-Charge, including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of Royality, Malkhana, Octroi, GST, Toll Tax Sales tax or any other taxes imposed by the Government. |
| 74 | 15mm (Fifteen millimetre) thick cement plasters in single coat on rough side of brick/concrete/stone walls for interior plastering upto all floor levels including arises, internal rounded angles, chamfers or rounded angles not exceeding 80mm (Eighty millimetre) in girth and finished even and smooth with cement mortar 1:6 (one cement isto six sand) as per specifications, approved drawing, design as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of Octroi, Royality, Malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 75 | 15mm (Fifteen millimetre) thick cement plasters in single coat on fair side of brick/concrete/stone walls for interior plastering upto all floor level including arises, internal rounded angles, chamfers or rounded angles not exceeding 80mm (Eighty millimetre) in girth and finished even and smooth with cement mortar 1:6 (one cement isto six sand) as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 76 | 15mm (Fifteen millimetre) thick cement plasters in single coat on fair side of brick/concrete/stone walls for interior plastering upto all floor levels including arises, internal rounded angles, chamfers or rounded angles not exceeding 80mm (Eighty millimetre) in girth and finished even and smooth with cement mortar 1:4 (one cement isto four sand) as per specifications, approved drawing, design as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of Octroi, Royality, Malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 77 | Forming 15mm (Fifteen millimetre) wide and 15mm (Fifteen millimetre) deep groove of uniform size in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer, including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 78 | Providing Plinth protection with 40mm (Forty millimetre) thick interlocking paver blocks of NTC with 23cm (Twenty three centimetre) dia half round RCC pipe for drainage purpose fixed over 10cm (Ten centimetre) thick cement concrete 1:4:8 bedding complete as per specifications, approved drawing, design as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of Octroi, Royality, Malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 79 | Applying Birla/J.K white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose material and other foreign matters, sand papered smooth to give final matt finish to the surface complete as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 80 | Finishing walls with apex weather proof exterior emulsion of Asian/Dulux/Berger/Nerolac Suraksha paints of approved shade having VOC less than 50 gm/litre (Fifty gram per litre) and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade with silicon additives New work (Two or more coats applied @ 1.43 litre/ 10 sqm (One point forty three litre per ten square metre) over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm (Zero point ninety litre per ten square metre) upto all floor level complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 81 | Painting Two or more coats on new work with synthetic enamel paint of Asian Paint /Nerolac Paints to givean even shade including thoroughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth including applying of putty as required form atting the surface smooth complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 82 | Distempering (two coats) with Acrylic and Synthetic oil bound washable distemper with Nerolac/ Asian of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matters and also including preparing the surface even and sand papered smooth as per specifications, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 83 | Providing and fixing 595x595x6mm (Five hundred ninety five into fiive hundred ninety five into six millimetre) designer board of everest (E-Board) ceiling with pre-painted GI channel framing @ 600mm c/c (Six hundred millimetre centre to centre) complete including curing as per PWD specification,approved drawing, design including cost and carriage of material within all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax,GSTand any other taxes imposed by the Government |
| 84 | 12.5mm (Twelve point five millimetre) thick 7.5cm (Seven point five centimetre) wide raised band in Plaster with cement mortar 1:4 (One cement isto four sand) complete including curing as per PWD specification, approved drawing, design including cost and carriage of material within all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax,GSTand any other taxes imposed by the Government. |
| 85 | Providing and laying plain cement concrete 1:2:4 (One cement isto Two sand isto Four graded broken/ crushed stone aggregate 20mm (Twenty millimetre) nominal size mechanically mixed vibrated and curing complete excluding cost of forms work in foundation and plinth complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 86 | Providing and laying cement concrete interlocking block 60mm (Sixty millimetre) thick (M35) Made with vibration technology PVC /Fibre moulds pew polished of NTC ISI marked IS No 15659 or its equiivalent as per approved shade and sample including border or kurb block grey or coloured over sub-base of concrete with 25mm (Twenty millimetre) thick average thickness of cement mortar 1:4 (One cement isto four sand) laid over and jointed with neat cement slurry mixed with pigment to match the shade of blocks including curing rubbing and polishing complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 87 | Providing and laying cement concrete 1:3:6 (One cement isto Three sand isto Six graded stone aggregate 40mm (Forty millimetre) nominal size and curing complete excluding cost of form work in foundation and plinth complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 88 | Providing and fixing to wall ceiling and floor ploythelene aluminium ploythelene (PE.AL.PE) composite pressure pipe U.V stabilized with carbon black and fitting of kitec confirming to ISI 15450-2004 for water supply complete with necessary pipe fitting including cutting, fixing and making good the walls ceiling and floor of approved brand complete as per HPPWD specifications and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate inclusive of Octroi, GST, Toll Tax, Sales tax or any other taxes imposed by the Government. 1620 (20mm (Twenty millimeter) outer diameters) |
| 89 | Providing and fixing to wall ceiling and floor ploythelene aluminium ploythelene (PE.AL.PE) composite pressure pipe U.V stabilized with carbon black and fitting of kitec confirming to ISI 15450-2004 for water supply complete with necessary pipe fitting including cutting, fixing and making good the walls ceiling and floor of approved brand complete as per HPPWD specifications and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate inclusive of Octroi, GST, Toll Tax, Sales tax or any other taxes imposed by the Government. 2025 (25mm (Twenty five millimeter) outer diameters) |
| 90 | Making connection of galvanised steel distribution branch with galvanised iron main 20mm to 40mm (twenty to forty milimeter) nominal bore by providing and fixing tee including cutting and threading the pipe complete as per approved drawing, design and specifications and as per direction and entire satisfaction of Engineer-in-Charge, including carriage of material within all leads, lifts and other incidentals. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sale Tax, GST or any other taxes imposed by the Government. |
| 91 | Providing and fixing 110mm (One hundered ten millimetre) nominal bore/diametres High pressure PVC PVC spigot and socket, waste and ventilating pipes 4.00 to 4.6mm thick (Four point zero zero to four point six millimetre) of Finolex/Vectus/Relience including fixing with approved adhesive etcetera complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 92 | Providing and fixing 75mm (Seventy five millimetre) nominal bore/diametres High pressure PVC PVC spigot and socket, waste and ventilating pipes 4.00 to 4.6mm thick (Four point zero zero to four point six millimetre) of Supreme/ Kisan/ Astral including fixing with approved adhesive etcetera complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 93 | Providing and fixing 110mm (One hundered ten millimetre) nominal bore/diametres P.V.C clamps ISI marked of Supreme/ Kisan/ Astral etcetera including finishing with approved design with steel screws and rawal plugs etcetera complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 94 | Providing and fixing 75mm (Seventy five millimetre) nominal bore/diametres P.V.C clamps ISI marked of Supreme/ Finolex/Kisan/ Astral etcetera including finishing with approved design with steel screws and rawal plugs etcetera complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 95 | Providing and fixing 110mm (One hundred ten millimetre) diametre P.V.C. Supreme/ Finolex/Kisan/ Astral heal rest Confirming to BIS-14735 including filling the joints with approved adhesive complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 96 | Providing and fixing 75mm (Seventy five millimetre) diametre P.V.C. Supreme/ Finolex/Kisan/ Astral heal rest Confirming to BIS-14735 including filling the joints with approved adhesive complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 97 | Providing and fixing 110mm (One hundred ten millimetre) P.V.C. (Polyvinyl chloride) plain bend make of Supreme/ Kisan/ Astral of approved manufacture ISI marked including fixing with approved adhesive etcetra complete and carriage of material within all leads, lifts and other incidental Charges. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sale Tax, GST or any other taxes imposed by the Government. |
| 98 | Providing and fixing 75mm (Seventy five millimetre) P.V.C. (Polyvinyl chloride) plain bend make of Supreme/ Finolex/Kisan/ Astral of approved manufacture ISI marked including fixing with approved adhesive etcetra complete and carriage of material within all leads, lifts and other incidental Charges.The rate is including Royality, Malkhana, Octroi, Toll Tax, Sale Tax, GST or any other taxes imposed by the Government. |
| 99 | Providing and fixing 110mm (One hundered ten millimetre) nominal size PVC Collar of ISI marked Conforming to BIS-14735-99 of Supreme/Finolex/ Kisan/ Astral including filling with approved adhesive etcetera complete in all floor level/height complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 100 | Providing and fixing 75mm (Seventy five millimetre) nominal size PVC Collar of ISI marked Conforming to BIS-14735-99 of Supreme/Finolex/ Kisan/ Astral including filling with approved adhesive etcetera complete in all floor level/height complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 101 | Providing and fixing 110mm (One hundered ten millimetre) nominal size PVC Cowl of ISI marked Conforming to BIS-14735-99 of Supreme/Finolex/ Kisan/ Astral including filling with approved adhesive etcetera complete in all floor level/height complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 102 | Providing and fixing 75mm (Seventy five millimetre) nominal size PVC Cowl of ISI marked Conforming to BIS-14735-99 of Supreme/Finolex/ Kisan/ Astral including filling with approved adhesive etcetera complete in all floor level/height complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 103 | Providing and fixing 110x90mm (One hundred ten into ninety millimetres) nominal size/ diameter PVC floor trap ISI marked Supreme/Kitch/Finolex/Kisan/ Astral Conforming to IS-14735-99 of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floor etcetera complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 104 | Providing and fixing 110x75mm (One hundred ten into seventy five millimetres) nominal size/ diameter PVC floor trap ISI marked Supreme/ Kitch/Finolex Conforming to IS-14735-99 of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floor etcetera complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 105 | Providing and fixing vitreous China wash down water closet (European type W.C. pan) Wall mounted WC size 57x35x39cm (Fifty seven into thirty five into thirty nine centimetre) of Cera/hindware/Jaquar with 10 litre low level PVC flushing cistern (Sleek plus) having dual flush system with fitting and brackets, 40mm (Forty millimetre) flush bend, 20mm (Twenty millimetre) over flow pipe, with seat & lid fixed with C.P. brass hinges and rubber buffers,with specials of standard make and mosquito proof coupling of approved municipal design complete including painting of fittings and brackets, cutting and making good the walls and and fixed with jet pressure and intergal P or S trap including jointing the trap and soil pipe with adhesive of approved brand. (Jet Spray to be measured and paid for separately) complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 106 | Providing and fixing water closet squatting pan (Indian type W.C. pan) White Vitreous china Orissa pattern WC 530x410 mm (Five hundred thirty into four hundred ten millimetre) of Cera/hindware /Jaquar with integral type foot rests with 100mm (One hundred millimetre) sand cast Iron P or S trap, 10 (Ten) litre low level P.V.C. flushing cistern, and as shown in the drawing /as per details including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 107 | Providing and fixing 32mm (Thirty two millimetre) diametre P.V.C. flexible waste pipe of Supreme/Finolex/ Relpipe (Reliance)/Vectus for sink or wash basin including P.V.C. waste necessary fitting complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 108 | Providing and fixing G.I. inlet connection for each flush pipe with W.C. pan including necessary fitting complete including entire carriage of material complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 109 | Providing and fixing vitreous China under counter wash basin Garnet No.10080 size 53x43Cm (Fifty three into forty three centimetre) of HINDWARE/CERA/JAQUAR or its equivalent with star white/snow white shade with single hole for pillar tap with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fittings complete including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 110 | Providing and fixing vitreous China wash basin No.2810 withour pedestal size 51x41Cm (Fifty one into forty one centimetre) of HINDWARE/CERA/JAQUAR or its equivalent with mirrior above of star white/snow white shade with single hole for pillar tap, 15mm (Fifteen millimetre C.P brass Pillar Tap, 32mm (Thirty two millimetre) C.P Brass waste with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fittings complete including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 111 | Providing and fixing white vitreous china flat back single half stall urinal Large flat back no 60002 of size 39x37.5x59cm (Thirty nine into thirty seven point five into fifty nine centimentre) with white PVC automatic flushing cistern of Hindware/ Cera/ Jaquar of star white / Snow white shade and as shown in the drawing / as per details with ittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required with 10 (Ten) litre P.V.C. automatic flushing cistern including necessary fitting complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 112 | Providing and Fixing Charomium plated 40mm (Forty millimetres) dia steel pipe for grab bars at 78cm (Seventy eight centimetres) height metres M.S.plate as per details at the portion of the seat and wash basin complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 113 | Providing and fixing white vitreous china pedestal type Matrix water closet (European type) with seat and lid, 10 litre (Ten) low level white PVC flushing cistern (sleek Plus) having dual flush system of Hindware/ Cera/ Jaquar of star white / Snow white shade and as shown in the drawing / as per details & C.P. flush bend with fittings & C.I. brackets, 40mm (Forty millimetre) flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid each including necessary fitting complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 114 | Providing and fixing wash basin White Vitreous China Flat back wash basin Delta No 10010 size 550x 400mm (Five hundered fifty into four hundered millimetre) (Under counter Basin ) Hindware/ Cera/ Jaquar of star white /Snow white shade and as shown in the drawing /as per details with single 15mm (Fifteen millimetre) C.P. brass pillar tap with C.I. brackets, 15mm (Fifteen millimetre) C.P. brass pillar taps, 32mm (Thirty two millimetre) C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required including necessary fitting complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 115 | Providing and fixing stainless steel kitchen sink of Diamond, big size 46x40Cm (Forty six into forty centimetre) of approved make with drain board and C.P waste with C.I or M.S brackets painted white including cutting holes in walls and making good the same complete including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 116 | Providing and fixing 32mm (Thirty two millimetre) dia M.I.union for Wash basin and sink long and 15mm (Fifteen millimetre) nominal bore with brass union complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 117 | Providing and fixing 15mm (Fifteen millimetres) nominal bore P.V.C. connection pipe with brass union 45cm (Forty five Centimeters) length complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 118 | Providing and fixing Mixer for kitchen sink with casted swinging spout at top complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 119 | Providing and fixing 32mm (Thirty two millimeters) nominal diameters PVC waste for wash basin or sink complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 120 | Providing and fixing two hole basin mixing Faucet of Continental series of Jaquar/Classik swries of Hindware/ Floral series of Cera/Vintage series of Kerovite & Hidon series of Jal complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 121 | Providing and fixing 100mm (One hundred millimetre) dia chromium plated (Heavy duty makes ISI marked) IS No. 8931 & 8934 grating of superior quality for floor, gully or nahani trap complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 122 | Providing and fixing 75mm (Seven hundred fifty millimetre) dia chromium plated (Heavy duty makes ISI marked) IS No. 8931 & 8934 grating of superior grating of superior quality for floor, gully or nahani trap complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 123 | Providing and fixing flat back 600x450mm (Six hundred into Four hundred fifty millimetres) beveled edge mirror of Opel of Jaquar / ESS-ESS of hoteior series of superior glass (of approved quality) complete with 6mm (Six millimetre) thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 124 | Providing and fixing 600x20mm (Six hundred into twenty millimeters) C.P brass towel rail. (Heavy duty makes ISI marked) IS No. 8931 & 8934 with C.P. brass brackets fixed to wooden plugs with C.P. brass screws complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 125 | Providing and fixing liquid soap container with C.P. Brass lid and brackets fixed to wooden plugs with C.P. Brass screws :-Plastic container complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 126 | Providing and fixing chromium plated brass toilet paper holder of approved brand and manufacture continental series of Jaquar/contessa series of Hindware complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 127 | Providing and fixing 8mm (Eight millimetre) C.P/S.S Jet of Continertal Series of Jaquar/Classik series of Hindware/Floral series of Cera/Vintage series of Kerovite & Hindon Series of Jal with flexible tube upto 1mtre (One metre) long with S.S tringular plate to Eurepean type W.C of quality and make complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 128 | Providing and fixing 600x120x5mm (Six hundered into One hundered twenty into five millimetres) glass shelf of Continental series of Jaquar /Classik series of Hindware /Floral series of Cera /Vintage series of Kerovite & Hindon series of Jal with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40mm (Fofrty millimetre) long screws, rawl plugs etcetera including necessary fitting complete including entire carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 129 | Providing and fixing 15mm (Fifteen millimetre) diametre C.P. brass. Bib tap of Continental series of Jaquar / Classik series of Hindware /Floral series of Cera /Vintage series of Kerovite and Hindon series of Jal approved quality (superior or heavy type) and colour complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 130 | Providing and fixing 15mm (fifteen millimeter) dia CP brass stop cock Continental series of Jaquar / Classik series of Hindware /Floral series of Cera /Vintage series of Kerovite and Hindon series of Jal complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 131 | Providing and fixing 15mm (fifteen millmeters) C.P. brass angle valve Continental series of Jaquar / Classik series of Hindware /Floral series of Cera /Vintage series of Kerovite and Hindon series of Jal complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 132 | Providing and fixing 15mm (Fifteen millimetre) nominal bore C.P. Push cock of Continental series of Jaquar/Classik series of Hindware /Floral series of Cera /Vintag series of Kerovite & Hindon series of Jal without nuts and pipes including necessary fitting complete including entire carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 133 | Providing and fixing 15mm (Fifteen millimeters) nominal bore brass full way valve with wheel of Continental series of Jaquar/Classik series of Hindware /Floral series of Cera /Vintag series of Kerovite & Hindon series of Jal complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 134 | Providing and fixing 15mm (fifteen millmeters) nominal bore C.P. brass valve (Horizontal plunger) type High pressure with polythene plastic floats of Continental series of Jaquar/Classik series of Hindware /Floral series of Cera /Vintag series of Kerovite & Hindon series of Jal complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 135 | Providing and fixing 110mm (One hundred ten millimetre) nominal size PVC single equal branch with oval access door, ISI marked of Finolex/Kitch/Supreme including insertion rubber washer 3mm (Three millimetre) thick including fixing with approved adhesive etcetera complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 136 | Providing and fixing 75mm (Seventy five millimetre) nominal size PVC single equal branch with oval access door, ISI marked of Finolex/Kitch/Supreme including insertion rubber washer 3mm (Three millimetre) thick including fixing with approved adhesive etcetera complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 137 | Providing and fixing 110mm (One hundred ten millimetre) nominal size PVC double equal branch with oval access door, ISI marked ofFinolex/Kitch/Supreme including insertion rubber washer 3mm (Three millimetre) thick including fixing with approved adhesive etcetera complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 138 | Providing and fixing 75mm (Seventy five millimetre) nominal size PVC double equal branch with oval access door, ISI marked ofFinolex/Kitch/Supreme including insertion rubber washer 3mm (Three millimetre) thick including fixing with approved adhesive etcetera complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 139 | Providing and fixing 110mm (One hundred ten millimetre) nominal size PVC door bend with oval access door, insertion rubber washer 3mm (Three millimetre) thick ISI marked of Finolex/Kitch/ Supreme including fixng with approved adhesive etcetera complete in all floor level/height etcetera complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 140 | Providing and fixing 75mm (Seventy five millimetre) nominal size PVC door bend with oval access door, insertion rubber washer 3mm (Three millimetre) thick ISI marked of Finolex/Kitch/ Supreme including fixng with approved adhesive etcetera complete in all floor level/height etcetera complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 141 | Providing and fixing 110mm (One hundred ten millimetre) nominal diametre PVC offset 45° of Finolex / Kitch /Supreme ISI marked including fixing with approved adhesive in all floor level/height etcetera complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 142 | Providing and fixing 75mm (Seventy five millimetre) nominal diametre PVC offset 45° of Finolex / Kitch /Supreme ISI marked including fixing with approved adhesive in all floor level/height etcetera complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 143 | Providing and placing on terrace (at all floor levels polyethylene water storage tank, tripple layer of Finolex/Kitch/Supreme IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 144 | Providing and laying cement concrete 1:5:10 (One cement isto five sand isto ten graded crushed stone aggregate 40mm (Forty millimetres) nominal size in all round for PVC pipe of 150mm (One hundred fifty millimetres) internal diametre including bedding necessary form work and curing complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 145 | Constructing brick masonry manhole in cement mortar 1:4 ( one cement isto four coarse sand) with R.C.C. top slab with 1:1.5:3 mix (one cement isto one & half coarse sand isto three graded stone aggregate 20 mm (Twenty millimetres) nominal size), foundation concrete 1:4:8 mix (one cement isto four coarse sand isto eight graded stone aggregate 40mm (Forty millimetres) nominal size), inside plastering 12mm (Twelve millimetres) thick with cement mortar 1:3 (one cement isto three coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (one cement isto two coarse sand isto four graded stone aggregate 20mm (Twenty millimetre) nominal size finished with floating coat of neat cement complete as per standard design Inside size 90x80 cm (Ninety into eighty centimetres) and 45 cm (Forty five centimetres) deep including C.I. cover with frame (light duty) 455x610 mm (Four hundred fifty five into six hundred ten milimetres) internal dimensions, total weight of cover and frame to be not less than 38 kg (Thirty eight kilogramme) (weight of cover 23 kg (Twenty three kilogramme) and weight of frame 15 kg (Fifteen kilogramme)) With Sewer bricks conforming to IS : 4885 complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 146 | Constructing brick masonry manhole in cement mortar 1:4 ( one cement isto four coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (one cement isto one & half coarse sand isto three graded stone aggregate 20mm (Twenty millimetres) nominal size), foundation concrete 1:4:8 mix (one cement isto four coarse sand (zone- III) isto eight graded crushed stone aggregate 40mm (Forty millimetres) nominal size), inside plastering 12mm (Twelve millimetres) thick with cement mortar 1:3 (one cement isto three coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (one cement isto two coarse sand isto four graded crushed stone aggregate 20mm (Twenty millimetres) nominal size) finished with a floating coat of neat cement complete as per standard design Inside size 120x90cm (One hundred twenty into Ninety centimetres) and 45 cm (forty five centimetres) deep including C.I. cover with frame (medium duty) 455x610mm (Four hundred fifty five into six hundred ten millimetres) internal diameter, total weight of cover and frame to be not less than 38 kg (Thirty eight kilogramme) (weight of cover 23 kg (Twenty three kilogramme) and weight of frame 15 kg (Fifteen kilogramme)) : With Sewer bricks conforming to IS : 4885 complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 147 | Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (One cement isto four coarse sand) C.I. cover with frame (light duty) 455x610mm (Four hundred fifty five into six hundred ten millimetre) internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (One cement isto one & half Fine sand isto three graded stone aggregate 20mm (Twenty millimetre) nominal size), foundation concrete 1:5:10 (One cement isto five fine sand isto ten graded stone aggregate) 40mm (Forty millimetre) nominal size, inside plastering 12mm (Twelve millimetre) thick with cement mortar 1:3 (One cement isto three coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etcetra complete as per standard design Inside dimensions 455x610mm (Four hundred fifty five into six hundred ten millimetre) and 45cm (Forty five centimetre) deep for single pipe line : 19.30.1.1 with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (Seven point five) complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 148 | Providing and fixing 600x300mm (Six hundred into three hundred millimetre) vitreous china division plate for urinals of Hindware/cera/Jaquar of star white /snow white shade complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 149 | Providing and fixing 20mm (Twenty millimetres) nominal bore in trenches galvanised mild steel tubes (heavy grade) ISI make approved quality tube fitting tube fitting and clamps complete including entire carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 150 | Providing and fixing 15mm (Fifteen milimetres) nominal bore to wall ceiling and floor galvanised mild steel tubes (Medium grade) ISI make approved quality tube fitting and clamps including making good the wall, ceiling and floor complete including entire carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 151 | Providing and laying 150mm nominal bore/diameter (to level or slopes) PVC pipe grade 'A' and jointing with approved adhesive ncluding testing of pipes and joints complete including entire carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 152 | Excavation in drains and channels etcetra in earth work in all kind of classification of soil such as pick work, jumper work, pick-jumper work, blasting work, soft and hard blasting and saturated soil, including chiselling or wedging out rocks where blasting work is prohibited or any other mixed variety of soil includinig shoring, strutting, de-watering and pumping or bailing out water (surface and sub soil water) upto any depth or any quantum of water including slush which may arise during de-watering or removal of slush, lift upto any height stacking the excavated soil clear from the edge of excavation and then returning the stacked soil in 15cm (fifteen centimetre) layers when required into plinths, sides of foundation etcetra consolidating each deposited layer by ramming, watering and then disposing of all surplus excavated earth as per specification, approved drawings, design as per the entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of Octroi, Royality, Malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 153 | Applying cement slurry on Reinforcement Cement concrete slab or cement concrete work using 2.75 kgs. (Two point seventy five Kilogram) of cement per square meter of floor area before laying cement concrete flooring including roughening, cleaning of the concrete surfaces complete as per HPPWD specifications excluding cost of centring and shuttering and as per direction and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 154 | Providing and applying 20mm (Twenty millimetre) cement plaster in two coat backing coat 10mm (Ten milimetre) and finishing coat 10mm (Ten milimetre) thick on fair side of brick/stone masonary walls for interior plastering up to floor two level including aamses internal rounded angle chamfers and or rounded angle in cement mortar 1:4 (One cement isto four sand) complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 155 | Supplying and fixing cast iron cover with rectangle frame 455x610mm (Four hundred fifty five into six hundred ten millimetre) (light duty) single seal pattern having weight not less than 23kg (Twenty three kilogramme) as per HPPWD specifications complete including entire carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 156 | Providing and fixing of water lifting pump of 1.00 HP (One point zero horse power) of serex/Kirloskar/ Crompton/Wortington including all necessary fittings complete in all respect including entire carriage of materials within all leads lifts and other incidentals, and as per specification and as per directed by the Engineer-Incharge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 157 | Providing 20x20mm (Twenty into twenty millimetre) square bar M.S Foot rest including fixing in man holes with 20x20x10cm (Twenty into twenty into ten centimatre) cement concrete 1:3:6 (one cement isto three sand isto six graded /crushed stone aggregate) 20mm (Twenty millimetre) nominal size as per standard design complete in all respect including entire carriage of materials within all leads lifts and other incidentals, and as per specification and as per directed by the Engineer-Incharge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government. Please Enable Macros to View BoQ information |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail