|
| 1 | Taking down chowkats or frame with shutters (without taking off shutters from the frame) exc 1.5 sqm and n exc 4.0 sqm each including cutting holes for taking out of holdfast & making good in CM (1:4) after fixing new chowkats/ frames complete all as specified. |
| 2 | All as per item No 1 above but not exc 1.5 Sqm each |
| 3 | S & F factory made coloured WPC door frame 100% Solid, size 125mm x 65 mm double rebated ,made from wpc material comprising of virgin PVC polymer of K value 58-60, calcium carbonate and natural fibres minimum compressive strength of 58 N/mm2, and resistance to spread of flame of class 'A' category with property of being termite / borer proof, water / moisture proof & fire retardant & fixed in position with SS dash fasteners of required dia and length, colour of door frame to match that of shutter all as per specifications drawings complete all as specified and directed. (colour to be approved by Engineer-in charge ) |
| 4 | All as per item No 3 above but of size 100 mm x 50 mm, single rebated. |
| 5 | All as per item No 3 above but of size 70 mm x 45 mm, single rebated for cupboards. |
| 6 | S & F factory made 35mm thick 100% Solid WPC solid decorative type flush Door Shutter of required size comprising of virgin PVC resin of K Value 58-60, Calcium Carbonate and natural Fibers and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded (Inner) with density not less than 650 kg/cum having good screw holding capacity, Minimum Compressive Strength of 50 N/mm2 , Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free. Water/ Moisture Proof, Fire Retardant and fixing with stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws. Material test certificate and authentication should be compulsory and shall be provided by the manufacturing company complete all as directed and specified. |
| 7 | All as per item No 6 above but 20 mm thick WPC shutter for cupboards complete all as specified and directed. |
| 8 | M&L for 30 mm thick factory made solid WPC gauged door shutter with wire mesh in three number of division with brown wood grain texture, including SS wire mesh fixed with (15 x 15 ) mm square tubes in side rails with screwing 8x28 heat metal zinc coated screws that can be removed or fixed again after changing of wire mesh when needed covered with moulded beading complete all as specified and directed.Note:- Gauged door shutter shall be fabricated from single piece of WPC board. |
| 9 | S&F stainless steel butt hinges of size 100 mm Class 'B' fixed full body threaded star headed counter ss sunk screws. |
| 10 | S&F continuous (piano) hinges, mild steel, bright finish or electro galvanised with of flap (when open) 30 mm etc complete all as directed and specified. |
| 11 | S&F 150 mm long stainless steel handles, cast type complete all as specified |
| 12 | S&F stainless steel tower bolt 200 mm long complete all as specified and directed. |
| 13 | S&F stainless steel sliding door bolt 250 mm long with hasp, staple (bolt type) and fixing clips of sheet, and fixing bolts and sliding bolts of SS complete all as directed and specified. |
| 14 | S&F 150 mm size hasp and staple, safety type, stainless steel with mild steel hinge pin including bolt to hinge plate and fixed with screws |
| 15 | S&F double legged floor door stopper 150 mm long of Stainless Steel with rubber etc complete all as specified and as directed |
| 16 | S&F ball catches with 8 mm dia steel ball magnet catches for cupboard shutter including striking plate as approved etc complete all as directed and specified. |
| 17 | Supply and fixing mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate ISI marked complete all as specified. |
| 18 | S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm fixed with stainless steel wire staples. |
| 19 | S & F in repairs 25 mm dia Stainless Steel 1 mm thick curtain rod including fancy type brackets, and decorative end caps etc. fixed to wall complete all as specified. |
| 20 | M&L for preparation of old painted wooden surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. |
| 21 | M&L for preparing of old steel or iron surfaces over 10 cm width or girth and applying one coat of Synthetic enamel paint. |
| 22 | M&L for aluminum alloy powder coated standard hollow section as mentioned below window frame (Bombay sliding) with two glazed shutter and one number wire gauged shutter sliding type, with aluminum sections as per Series-B (18mm) 3 track of Jindal section for sliding windows, with and including glass to shutters tinted/ coloured glass 5mm thick, fixed with glazing clips, rubber beading / gasket anodised beading, screw and lock type 2 Nos aluminium handle of size 75mm and locking system including aluminium grill of 5 mm thick, average width of aperture 50mm including S&F stainless steel wire cloth to shutter with 0.36 mm dia of wire and 1.40 aperture complete all as specified and directed. |
| 23 | M & L 75 mm thick cement concrete type D-2, 1:4:8 (40mm graded crushed stone aggregate) including necessary form work as in sub base for flooring etc., complete all as specified. |
| 24 | M & L for 25 mm thick PCC 1:2:4 type B-0, (using 12.5 mm graded crushed stone aggregate) as in floors, to receive surface of tile including demolition of old PCC/ flooring complete all as specified and directed. |
| 25 | M & L for 8-10 mm thick vitrified tiles of light shade of size 600 x 600 mm Group B i (a) in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incl screed bed or bedding layer of mortar, 15 mm thick, in cement mortar 1:6,complete all as specified and directed. |
| 26 | All as per item No 25 above but on vertical surfaces as in skirting, dados over and including 10 mm thick rendering in CM 1:4 including dismantling of old skirting complete. |
| 27 | M&L for Non skid vitrified (heavy duty) ceramic coloured tiles 8 to 9mm thick (Square or rectangular) Group B i (a) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, laid in floors etc, set and jointed in neat cement slurry and pointed in epoxy coating grout to match the shade of tiles with and including laying of 15 mm thick screed bed or bedding layer in CM 1:6 complete including dismantling of existing floor tiling including cement mortar bedding and removing rubbish off the premises complete all as directed. |
| 28 | All as per item No 27 above but on vertical surfaces as in skirting, dados over and including 10 mm thick rendering in CM 1:4 including dismantling of old skirting complete. |
| 29 | M & L 16 mm thick granite (colour as approved by GE) stone slab machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing including 15 mm thick cement screed bed 1:6 CM as in door & window cill and small pieces for soap dish etc including cutting,chases and inserting in wall in horizontal or vertical surfaces including grinding the edges half round where required) and polishing complete all as specified and directed. |
| 30 | M&L for Cutting holes superfacial area exc 150 but n exc 400 Sqcm into or through brick walls built in cement mortar and making good in CM 1:3 or cement concrete 1:2:4 type B-l as required |
| 31 | S&F in repairs, 75 mm bore outlet cast iron floor trap incl cockroach trap with gratings including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) etc complete all as specified. |
| 32 | S&F in repairs, 50 mm bore Cast iron (vertically cast spun pipe) soil, waste and vent pipes, in any length without ears, laid in trenches or in floors or fixed to wall complete all as specified and as directed |
| 33 | S&F in repairs, for 75 mm bore Cast iron (vertically cast spun pipe) soil, waste and vent pipes, in any length with, laid in trenches or in floors or fixed to wall complete all as specified. |
| 34 | S&F in repairs, 100 mm bore Cast iron (vertically cast spun pipe) soil, waste and vent pipes, in any length without ears, laid in trenches or in floors or fixed to wall, complete all as specified. |
| 35 | S&F in repairs, 75mm bore cast iron Tee of (any radius) equal or unequal, spun pipe diminishing pieces or tapers (larger bore measured) with oval access door complete all as specified. |
| 36 | S&F in repairs, 100 mm bore cast iron Tee of (any radius) equal or unequal, spun pipe diminishing pieces or tapers with oval access door complete all as specified. |
| 37 | S&F in repairs, 50 mm bore cast iron cowls complete all as specified and as directed |
| 38 | M & L Bands, straps, including bolts, if required, clamps, hooks for hanging fans and similar small articles conforming to Fe-290 Gde-E-165. |
| 39 | M&L for 15mm thick (Average thickness) rendering on fair faces of concrete in sunken portion in CM 1:3, mixed with water proofing compound on vertical and horizontal surfaces and providing slope towards outer wall and finished even and smooth without using extra cement. |
| 40 | M&L for 15mm thick rendering in CM 1:3 on damaged portion of concrete in small patches (in repairs) to facia/ ceiling of roof projection in double storied building including removing loose material on vertical and horizontal surfaces finished even and smooth without using extra cement. |
| 41 | M&L for water proofing treatment to sunken roof slab with APP based modified polymeric membrane as per manufaturer's instructions with following course of description(a) Applying a priming coat of bituminous primer @ 0.30 kg/sqm, till the surface is properly impregnated.(b) Apply a coat of bitumen 85/25 grade @1.20 kg/sqm over primer.(c) Over the coat of bitumen as above APP modified polymeric membrane (weight not less than 3.5 Kg/Sqm with over lap of 100mm). The overlaps are then sealed/fused by flame or bitumen Note: Rate of this item inclusive ponding test demolition and removal of old sunken WPT. The ponding test (for 48 hours) shall be crried out by the contractor, if any defect noticed the same portion shall be rectified by redoing by contractor without any extra cost to Govt. |
| 42 | M&L Cement concrete1:7:12 in sunken portion filling and mass concrete as directed. |
| 43 | M&L for Non skid glazed ceramic coloured tiles 7 to 8mm thick Group B i (a) area of each tile exc 0.06 Sqm but not exc 0.11 Sqm, laid in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles with and including of 15 mm thick screed bed in CM 1:6 complete. |
| 44 | M&L Glazed ceramic tiles coloured 300mmx 450mm , 7 to 8 mm thick Group B i (a) on vertical surface of wall such as skirting/ dados, set and jointed in neat cement slurry and pointed in white or colour cement to match with and including 10 mm thick rendering in CM 1:4, including dismantling existing wall tiles/ dados, complete all as specified and as directed. |
| 45 | M&L PCC/ RCC 1:2:4 type B-1 using 20 mm graded stone aggregate in benching and copings and small counters etc incl demolition of existing concrete as directed. |
| 46 | M&L for brick work with sub class 'B' bricks, in half brick thick wall built in CM 1:4 straight or curved on plan to any radius with old size bricks incl demolition of old brick work complete all as directed. |
| 47 | M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed. |
| 48 | M&L for PCC 1:3:6 type C-1 (20 mm graded stone aggregate) as in surface channels and drains. (Saucer Drain)including demolition of old PCC complete all as directed. |
| 49 | M & L for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement incl forms, moulds, mitred/ stopped ends etc. complete. |
| 50 | M&L for 15mm thick rendering on other than fair faces of brick/ concrete surfaces in CM 1:6 finished even and fair including taking down old cement plaster raking out joints hacking for keys, scrubbing down with waters etc, complete. |
| 51 | M&L for 15mm thick rendering on fair faces of brick/ concrete surfaces in CM 1:4 finished even and fair including taking down old cement plaster raking out joints hacking for keys, scrubbing down with waters etc, complete all as specified and directed. |
| 52 | M&L for Complete removal of existing treatment from walls. |
| 53 | M & L for preparation of new or old wall surface and applying 0.75 to 1 mm thick Birla white/ JK wall care putty over internal and external plaster to make the surface smooth as specified and directed. |
| 54 | M&L for preparation of new plastered or unplastered surfaces of walls and applying two coats of distemper oil emulsion, white or tinted, over one coat of alkali resistant primer complete all as specified & directed. |
| 55 | M&L for preparation of old decorated plastered surfaces of ceiling and applying one coat of whitewash complete all as specified & directed. |
| 56 | M & L for applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces. |
| 57 | S&F in repairs, medium grade galvanized steel tubing with all fittings &fixed complete to walls & ceiling or laid in floors 15 mm dia bore pipe (including in short length) complete all as specified and as directed |
| 58 | S&F in repairs, tubes medium grade galvanized with all fittings and laid in trenches, 20 mm bore dia pipe (including in short length) complete all as specified and as directed |
| 59 | S&F in repairs 500 litre rotational moulded triple layer polyethylene water storage tanks ISI marked of approved make white colour (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified in SSR Part-I, including one no PTMT ball valve high pressure and two nos of 20 mm dia gun metal gate valve to each tank, complete all as specified and directed. |
| 60 | M & L for cutting chases for concealed water tubing etc and making good cutting not exc 10 cm girth complete all as specified and as directed. |
| 61 | Supplying and laying in repairs, of 16 mm outer dia CPVC pipes pressure rating 6kg/cm2 SDR 11 & Plain CPVC SDR 11 fittings on walls/ ceiling or laid in floors complete all as specified. |
| 62 | Supply only Male Brass Threaded Adaptor (MBTA) 16 mm outer dia for CPVC pipes ISI marked. |
| 63 | Supply only Brass elbow 16 mm outer dia for CPVC pipes ISI marked |
| 64 | S&F Vitreous china squatting pan, 'Orissa' pattern, size 580 x 440 mm white, with integral foot rests including replacement of 'P' or 'S' CI, concrete bedding and making good existing floor fixed in repair complete all as specified and directed. |
| 65 | S&F Vitreous china wash down water closet pan (pedestal pattern) white including seat cover with necessary PVC pipe fittings fixed in repair complete all as specified and directed. |
| 66 | S&F PVC low level flushing cistern 10 Ltr capacity conforming to relevant IS or ISI marked of approved make syphonic action type white including ball valve, float valve and handle including bracket and PVC flush pipe fixed in repair complete all as specified and directed. |
| 67 | S&F in repairs, vitreous china counter top wash hand basin white of size approx 450x300mm, fixed over RCC counter, CP waste coupling & waste pipe complete all as specified and directed |
| 68 | S&F in repairs cast copper alloy stop valves/ angle valve 15mm bore fancy type chromium plated, screwed down, high pressure, screwed both ends for iron pipe or for unions and fixed. Make : Jaquar Opal Prime Series/ Cera Ruby series/ Kolher |
| 69 | S&F in repairs, 15 mm bore chromium plated, fancy type. long body bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed. Make : Jaquar Opal Prime Series/ Cera Ruby series/ Kolher |
| 70 | S&F in repairs, mirror bevelled edge, of size 450 x 600 mm of selected quality glass 5mm to 5.5mm thick of approved make mounted on 6mm AC building board or commercial ply wood, fixed to plugs with CP brass screws and cup washers |
| 71 | S&F 15mm size PVC connection with PTMT nuts length 450mm long ISI marked of approved make. |
| 72 | S&F in repairs sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long of approved make. |
| 73 | S&F in repair Toilet paper holder with flat recessed type stainless steel Complete all as specified and directed |
| 74 | S&F CP brass hot & cold single lever basin mixer with 450mm long braided hoses cast copper alloy with centre hole for WHB complete all as directed. Make : Jaquar Opal Prime Series/ Cera Ruby series/ Kolher |
| 75 | S&F CP brass hot & cold 15mm dia wall mixture for mixing hot & cold water with shower (3 way)provn with connecting legs & flanges in complete all as specified. Make : Jaquar Opal Prime Series/ Cera Ruby series/ Kolher |
| 76 | S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. |
| 77 | S&F in repair CP brass chromium plated shower rose 125mm size with extension CP Arm pipes of approved make |
| 78 | S&F in repair brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges of approved make |
| 79 | S & F for stainless steel glossy finish hat peg set of five tier with necessary fitting complete all as specified and directed. |
| 80 | S&F fancy type glass corner 300mm radius of 10mm thick toughned glass with CP railing fixed with fancy type screws complete all as specified and directed. Model: ACN - 1173 of Jaquar , Parryware Model No T6010A1, Cera Model No F505101 |
| 81 | Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surface of walls, floors, etc. |
| 82 | Taking down old U/S main switches, Sheatmetal enclosures DB including MCCBs, MCBs etc including making good to the disturbed surface of wall all as directed. |
| 83 | Taking down old unsv T/L, Lamp,Security light of any size and capacity all as directed. |
| 84 | Taking down carefully submain wiring including all accessories without disturbing existing wiring fittings fixtures etc and making good to the disturbed surfaces all as directed and as specified in any type and size all as directed. |
| 85 | Taking down existing ceiling fan of any capacity and make serviceable by replacing unsv parts and preparation of old painted surface body and blades of ceiling fan of any capacity ,cleaning foreign material ,filling cavaties atc and painting with one coat of synthetic enammeled paint by spray painting and marking MES No. with paint and kept in safe custody and refixing at site after compltion of bldg work. Please Enable Macros to View BoQ information |
| 86 | Taking down existing ceiling fan of any capacity and make serviceable by replacing unsv parts and preparation of old painted surface body and blades of ceiling fan of any capacity ,cleaning foreign material ,filling cavaties atc and painting with one coat of synthetic enammeled paint by spray painting and marking MES No. with paint and kept in safe custody and refixing at site after compltion of bldg work. Please Enable Macros to View BoQ information |
