Tender For Construction Of Integrated Commercial Taxes Office Building At Alapakkam In Chengalpattu District., Chennai-Tamil Nadu

TDR : 54434014

Tender Notice
BOQ

2 Days Left

Chennai , Tamil Nadu

Tender Brief : Tender For Construction Of Integrated Commercial Taxes Office Building At Alapakkam In Chengalpattu District.

Document Fees
Refer document

EMD
₹ 2082500.0 /-

Tender Value
₹ 41.45 Crore /-

Submission Date
09-03-2026

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	Earth work excavation for foundation by manual means for Isolated, Combined and Other type foundations in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2.00mts. and clearing and levelling the site, etc., complete complying with standard specification and as directed by the departmental officers.
2	Upto 2.40m depth
3	Earth work open excavation by manual means in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification and as direct- ed by the departmental officers.
4	Upto 2.40m depth
5	Above 2.40m depth
6	Supplying and filling in foundation, basement, etc with filling Crushed Stone sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.
7	Supply and filling in foundation and basement with Gravel in layers of not more than 15cm.thick well rammed watered and compacted with surface vibrator, watered and consolidated etc. complete complying with standard specification and as directed by the departmental officers.
8	Refilling with excavated earth other than sand with an initial head load of 100 mts. and depositing the earth as shown by the departmental officers in layers of not more than 15cm thick well rammed with surface vibrator, watered and consolidated etc., complete complying with standard specification and as directed by the departmental officers.
9	Wet Mix Macadam (Table 400-13) (Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density, Complete as per clause 406) as per MORT&H Rev. V Specifications No. 111,112,406,900
10	Cement Concrete 1:5:10 (One Cement, Five crushed stone sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and including curing etc. complete complying with standard specification and as directed by the departmental officers. - Mixing by manual means
11	Brick work in Cement Mortar 1:3 ( One Cement and Three M-Sand) using best quality Fly ash Brick of size 230x110x70mm with class designation of 7.5 conforming to IS 13757-1993 or IS 12894-2002 for foundation and basement including Cost of Mortar Plasticizer, curing, etc., complete complying with standard specification and as directed by the departmental officers. Brickwork shall be done as per IS 2212-1991 adopting English Bond generally. other type of bond shall be done as directed by the Executive Engineer in charge.
12	FOUNDATION AND BASEMENT
13	Brick work in Cement Mortar 1:5, (One Cement and Five M-Sand) using best quality Burnt Clay Brick of size 9\\" x 4 3/8\\" x 2 3/4\\" with class designation of 7.5 conforming to IS 1077-1992 for foundation and basement including Cost of Mortar Plasticizer curing, etc.,complete complying with standard specification and as directed by the departmental officers. Brickwork shall be done as per IS 2212-1991 adopting English Bond generally.other type of bond shall be done as directed by the Executive Engineer in charge.
14	FOUNDATION AND BASEMENT
15	GROUND FLOOR
16	Brick work in Cement Mortar1:6 ( One Cement and Six M-Sand) using best quality Fly ash Brick of size 230x110x70mm with class designation of 7.5 conforming to IS 13757-1993 or IS 12894-2002 for foundation and basement including Cost of Mortar Plasticizer, curing, etc., complete complying with standard specification and as directed by the departmental officers. Brickwork shall be done as per IS 2212-1991 adopting English Bond generally. other type of bond shall be done as directed by the Executive Engineer in charge.
17	GROUND FLOOR
18	FIRST FLOOR
19	SECOND FLOOR
20	THIRD FLOOR
21	FOURTH FLOOR
22	FIFTH FLOOR
23	SIXTH FLOOR
24	Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10x6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid)
25	Supplying and erecting centering for plane surfaces such as RCC Floor/Roof Beam, Lintels, Cantilever Beams, Bed Blocks etc.. with necessary supports and strutting upto 3.60m height in all floors with all cross bracings using MS Sheets made of 10 gauge thick welded with MS angle of Size 25mm x 25mm x 3mm for boarding laid over Steel adjustable Span of Size 2m x 2m(expandable upto 3.60m) and Silver Oak Joists of Size 10 x 5 cm spaced at 50cm to 60cm c/c and supported by Steel Adjustable Telescopic Props of Size 2m x 2m (expandable upto 3.60m) made with outer steel pipe with dia 50mm (3.60mm thick) and inner steel pipe with dia 40mm (2.90mm thick) Spaced at not more than 50 to 60cm c/c, etc complete complying with standard specifications. Steel adjustable span and Steel Adjustable telescopic props shall be provided as directed by the departmental Officers. (Payment for centering shall be given after the concrete is laid).
26	Supplying and erecting centering for plane surfaces such as RCC Floor Slab, Roof Slab, Loft, Landing Slabs, etc with necessary supports and strutting upto 3.60m height in all floors with all cross bracings using MS Sheets made of 10 gauge thick welded with MS angle of Size 25mm x 25mm x 3mm for boarding laid over steel adjustable span of size 2m x 2m (expandable upto 3.60m) and supported by Steel Adjustable Telescopic Props of Size 2m x 2m (expandable upto 3.60m) made with outer steel pipe with dia 50mm (3.60mm thick) and inner steel pipe with dia 40mm (2.90mm thick) , etc complete complying with standard specifications. Steel adjustable span and Steel Adjustable telescopic props shall be provided as directed by the departmental Officers. (Payment for centering shall be given after the concrete is laid).
27	Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as vertical slab, side slabs of boxing, vertical drops, facia, vertical wall, etc. using mild steel sheets of size 1200cm x 60cm and 10 BG stiffened with welded mild steel angles of size 40mm x 40mm x 5 mm for boarding, laid with silver oak joists of size 10cm x 5cm & 7.5cm x 5cm as support runner, Top Horizontal stiffener spaced at about 60cm to 90cm centre to centre or at suitable intervals. MS Channel Section (ISMC 100) shall be provided as a vertical support @1.20m C/C and with Lateral support of Steel Adjustable Telescopic Props of Size 2m x 2m (expandable upto 3.60m) & steel pipes of 20mm dia @ required level/spacing etc. complete complying with standard specifcation and as directed by the departmental officers. (Payment for centering shall be given after the concrete is laid)
28	Supplying and erecting steel centering including necessary supports For plane surfaces such as rectangular or square RCC columns etc. which require only nominal strutting using mild steel sheets made of 10 gauge thick welded with MS angle size 40mm x 40mm x 5 mm and supported by Steel Adjustable Telescopic Props of Size 2m x 2m (expandable upto 3.60m) made with outer steel pipe with dia 50mm (3.60mm thick) and inner steel pipe with dia 40mm (2.90mm thick).etc..complete in all floors complying with standard specifcation. Steel Adjustable telescopic props shall be provided as directed by the departmental Officers. (Payment for centering shall be given after the concrete is laid).
29	Providing and laying in position, standardised concrete Mix M-20 Grade by insitu machine mix concrete adopting weighing batch method in accordance with IS 456 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 kg/m3 and maximum water cement ratio of 0.55, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m) 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS standards. (No separate payment will be made by the Department for the excess usage of materials).
30	Foundation and basement
31	In Ground floor
32	Providing and laying in position, Standardised Concrete Mix M-25 Grade by insitu machine mix concrete adopting weighing batch method in accordance with IS:456-2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 350 kglm3 and maximum water cement ratio of 0.50, including admixture (plasticiser / superplasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m') 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).
33	FOUNDATION AND BASEMENT
34	GROUND FLOOR
35	FIRST FLOOR
36	SECOND FLOOR
37	THIRD FLOOR
38	FOURTH FLOOR
39	FIFTH FLOOR
40	SIXTH FLOOR
41	Providing and laying in position, Standardised Concrete Mix M-35 Grade by insitu machine mix concrete adopting weighing batch method in accordance with IS:456-2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 425 kg/m3 and maximum water cement ratio of 0.45, including admixture (plasticiser / superplasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m') 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).
42	FIFTH FLOOR
43	Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel reinforcement grills of all variety like HYSD/CTD/TMTand all grade like Fe 500, Fe550D, Fe 500 D etc., for all RCC works as per design given including cost of steel reinforcement and G.I. binding wire, wastage etc. complete complying with standard specification and as directed by the departmental officers.(Contractor has to make his own arrangements for the supply of steel reinforcement and binding wire)
44	FOUNDATION AND BASEMENT
45	GROUND FLOOR
46	FIRST FLOOR
47	SECOND FLOOR
48	THIRD FLOOR
49	FOURTH FLOOR
50	FIFTH FLOOR
51	SIXTH FLOOR
52	Post Tensioning Work: Design and execution of post tensioning work, including decoiling, the strands, cutting to the required lengths, supplying, laying of HT strands sheathing (GI corrugated ducts 0.3mm thick) jointing with couplers and inserting the strands, profiling, fixing liveend anchorages, including supply of stressing anchorages, suitable for 5-5 & 5-4 tendons, grout vents, making dead end anchorages, including flowering the strands, fixing tendon support bars, supervising the fixing of antibursting reinforcement, stressing the cables, end trimming, grouting the cables, with cement slurry, mixed with admixtures with required tools, plants, and machineries, and consumables etc. (Shuttering, concreting & reinforcement steel shall be paid under respective items) at all heights including all leads, lifts, coordination, with the post- tensioning agency, preparation of drawings, obtaining approval from the Employer / Architect etc. Rate to include providing water, power, cement and admixture for grouting, packing of sheathing and anchorages blockings, filling of recess pockets after stressing using grouts (cement slurry mixed with approved admixtures) including providing access to post tensioning at all heights including all leads, lifts etc., all complete and as approved and as directed by the Employer Architect but excluding shuttering, concreting & reinforcement steel which shall be payable under respective items separately.
53	Plain Cement Concrete 1:2:4 (one cement, two crushed stone sand and four hard broken stone jelly) using 20mm jelly for wearing coat including laying, compacting, finishing and curing, etc., complete as per standard specificatins and as directed by the departmental officers.- Mixing by manual means
54	Brick partition walls of 11.50cm thickness using best quality Burnt Clay Brick of size 9\\" x 4 3/8\\" x 2 3/4\\" with class designation of 7.5 conforming to IS 1077-1992 in Cement Mortar 1:3 (One Cement and Three CS Sand) using hoop iron reinforcement if found necessary including Cost of Mortar Plasticizer, curing etc. complete complying with standard specification and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately)
55	GROUND FLOOR
56	FIRST FLOOR
57	SECOND FLOOR
58	THIRD FLOOR
59	FOURTH FLOOR
60	FIFTH FLOOR
61	Brick Jelly Lime Concrete of 1:2:5 (One Lime,Two Sand and Five Brick jelly ) with 40mm hand broken brick jelly for Sunken portions including dewatering wherever necessary and laid in layers of not more than 15cm thick, well rammed, consolidated and curing etc. complete complying with standard specification.
62	Laying of screed concrete using Cement concrete mix 1:2:4 ( one cement, two sand and four hard broken stone jelly) using HBGS 6-10mm ISS metal for wearing coat including laying, compacting, finishing and curing etc., complete as per standard specification and as directed by the departmental officers
63	Paving the floor with best approved quality fine polished Granite Stone Slabs of following size and Synthetic Grey, Paradise and similar varieties with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) with required Cement Slurry and Mortar Plasticizer and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., complete complying with standard speicification and as directed by the departmental officers.(The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work)
64	Paving the floor with best approved quality fine polished Granite Stone Slabs of Flamed Steel Grey Granite Slab 1200mm x 600mm, 16mm to 18mm Thick with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) with required Cement Slurry and Mortar Plasticizer and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., complete complying with standard speicification and as directed by the departmental officers.(The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work)
65	Paving the floor with best quality vitrified Tiles of 600x600x8mm and variety conforming IS 15622 with water absorbtion less than 0.08% of approved colour and shade laid over cement mortar bed of 20mm thick in cement mortar 1:3 (one cement and three crushed stone sand) with required Cement Slurry and Mortar Plasticizer in all floors and the top pointed with Water Resistant Tile Epoxy Grout etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)
66	Paving the floor with best quality Matt Finished Vitrified Tiles 600x600x8mm of approved colour, shade andquality laid in cement mortar 1:3 (one cement and three sand)20mm thick in all floors and the top pointed with the white cementmixed same colour pigments etc., complete complying withstandard specification.(The make and brand of the tiles should be Johnson / Kajaria / Somany / Nitco/RAK which has to be gotapproved by Executive Engineer before use on works)
67	Paving the floor with best approved quality fine polished Kota stone slabs of size 600 x 600 and above 20mm thick with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) with required Cement Slurry and Mortar Plasticizer fixing the slabs in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments and polishing with floor polisher to a high degree of finish etc., complete complying with standard speicification and as directed by the departmental officers. (The kota stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work)
68	Supplying and laying of Interlocking Paver Block Stone 60mm thick Over a base layer of crushed stone sandfilling incl. Cost of materials laying and Labour charges etc complete complying with the standard specification and as directed by the departmental officers.
69	Dadooing walls with following best approved quality, white / colour glazed tiles conforming to IS 15622 of 300mm x 600mm x 10mm in Cement Mortar 1:2 (One Cement and Two crushed stone sand),10 thick with Mortar Plasticizer and pointing the joints with Water Resistant Tile Epoxy Grout at the rate of 0.27 Kg. / sq.m. neatly in all floors, curing, etc., complete complying with standard specification and as directed by the departmental officers.(The make and brand of the tiles should be got approved by Executive Engineer before use on works)
70	Dadooing walls with Granite slabs (Super fine polished with machine cut edges) of sizes 4'x2' and above 18mm to 20mm thick Jet Block in Cement Mortar 1:2 (One Cement and Two crushed stone sand),10 thick with Mortar Plasticizer and pointing the joints with Water Resistant Tile Epoxy Grout at the rate of 0.27 Kg. / sq.m. neatly in all floors, curing, etc., complete complying with standard specification and as directed by the departmental officers.(The make and brand of the tiles should be got approved by Executive Engineer before use on works)
71	Paving the Top of roof with Solar refelective ceramic tiles of approved quality and colour laid in Cement mortar bed in 1:3 (One cement and three crushed stone sand) 12mm thick and pointed with water resistant tile epoxy grout for joint, curing etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by the Executive Engineer before use on works)
72	Supplying and fixing fine polished cuddapah slab of following thickness for cup-board arrangements including laying to correct alignment with necessary cement mortar and black powder etc, complete complying with standard specification and as directed by the departmental officers
73	Providing Cup-board Shutter using termite / water proof plywood of 19mm thick over which laminated sheet of 0.8mm thick fixed inside the shutter and 1mm thick fixed in the outside of the shutter using fevicol along with necessary furniture fittings, such as, hydralic hinges, tower bolt, handles, multi purpose locks etc., as directed by the Departmental Officers. The design pattern, water proof plywood, laminate sheet and other materials should be got approved from the Executive Engineer before use on work.
74	Supplying Fabricating and placing in position of Aluminium With powder coating of any colours fixed Partition top half glazed with 5.50mm thick plain glass and bottom half with medium density fibre board of 12mm thick both side pre laminated for cubical and the outer frame of the Aluminium section of size 101.60x44.45x3.18mm @ 2.319Kg/m. at internal vertical 2 Nos & Horizontal 1 No, mullion of aluminium section of size 62 x 38 x 2mm @ 1.174 Kg/m with necessary aluminium clips of size 79.15 x 17.27 x 1.50mm at 0.176 Kg/m with necessary rubbor beading L angles including dismantling and redoing masonry as concrete where necessary etc., complete. The Aluminium section are to be anodised with matt finish under electrically controlled condition in allfdjsfdslk with ISI 1868 / 1962 specification for an average anodie film thickness of not less than 15 microns. All aluminium sections are should be got approved by Engineer incharge before use on works.
75	Fabricating Supplying and fixing in position of Aluminium anodised natural colour matt finish of single leaf door with half panelled with 12mm thick both side laminated particle board at bottom and half glazed using 5.50mm thick Plain glass at top.The outer frame shall be with aluminium box section 101.60x44.45x3.18m at 2.319kg/m and Shutter frame made of section Vertical & Top rail: 50x44.45x2.50mm @ 1.292 kg/m ,Bottom rail: 100 x44.45 x 2.50mm@ 1.974 kg/m, Lock rail : 50x44.45x2.5mm @ 1.292 kg/m, Alu Clips: 17.15x17.27x1.50mm @ 0.176 kg/m,Alu. Handle: 100x30mm @ 0.988 Kg/m and necessary accessories such as aluminium clips, rubber beading, PVC felt, handle for a length of shutter (both sides), locking arrangements, furniture fittings such as aluminium tower bolts-250x12mm - Each., aluminium tower bolt 200x12mm - 1No., aluminium Hydraulic door closer - 1No ., lock-1No., Door stopper with rubber bush including cost of materials labour charges and power consumption charges required for fabrication including chipping, dismantling and making hole to the required extent in RCC column, beams, masonry with power drill wherever necessary and redoing the damaged portion to the original condition after fixing etc., complete complying with standard specification and as directed by the deparmental officers.
76	All the Alu. Section are to be anodised with matt finish under electricaly controlled conditions in accordance with IS 1868/1962 for an average anatic film thickness of 15 microns etc., complete.Aluminium sections,and furniture fittings shall be got approved by the Executive Engineer incharge. including cost of furniture fitting such as Pivot, hinges, Tower bolt, lock, door stopper and all materials labour power consumption required for fabrication drilling required for fabrication drilling holes in RCC columns floorslabs masonry wall wherever necessary with power drills to the required extent and make the same to original condition after fixing and as directed. All the aluminium sections are to be anodised with matt finish under electrically controlled condition in accordance with IS 1868-1962 for an average anodic flim thickness of 15 microns etc., complete. The materials should be got approved by the Executive Engineer before use on works.The rate shall be inclusive of all materials, labour for fixing transportation loading, unloading, and all other incidential charges.
77	Providing expansion joint in RCC floor slab for 12.5mm width using polysulphide as sealent on the top and bottom for a depth of 7.5mm each and packing the inner space using compressible non-absorbent filler materials including cost of labour for cutting and fixing filler materials and laying polysulphide sealent with necessary spatula etc., complete complying with standard specifications and as directed by the departmental officers
78	Providing expansion joint 12.5mm width in RCC roof slabs between RCC twin beams using PVC water bar of 150mm wide centre bulb of 4mm to 6mm thickness of approved quality and brand and including filling the inner space with suitable non-absorbent flexible and well compressible filler materials of approved quality and covering the top surface with GI sheet 30cm wide and 1.6mm thick using phill plugs, GI screws, limpet cup washers, bitumen washers, etc., complete complying with standard specifications and as directed by the departmental officers.
79	Providing expansion joint of 12.5mm wide in between RCC twin columns from top of pedastal to full height including filling the inner space with suitable non-absorbent, flexible and well compressible filler materials of approved quality and brand; finishing the sides of RCC columns with polysulphide sealents for a depth of 7.5mm on either side covering the inner space filled with filler materials as above etc., complete complying with standard specifications and as directed by the departmental officers.
80	Providing grooving to granite slab at the intermediate edges of the vertical face with neat finishing etc complete with standard specification and as directed by the departmental officers. The cost including higher charges of machines and labour charges etc complete
81	Providing double semi nosing to granite slab at the edges of the Horizontal & vertical space with neat finishing etc complete with standard specification and as directed by the departmental officers. The cost including higher charges of machines and labour charges etc complete
82	Providing and Fixing of PVC Trims (Corner beeding) at the outer corner profiles of the tiles including cost of material, labour and handling etc. as directed by departmental engineers at site of work and as per standard specification.
83	Supplying and fixing in position of Urinal Partition using Granite Slab of size 0.60x1.20m with fixing with special clamp with bolt nut the rate inclusive of cost of materials and labour charges etc.,
84	Plastering with Cement Mortar 1:5 (One cement and Five Plastering sand), 12mm thick in all floors including mortar plasticizer at 200ml per 50Kg of cement used, curing etc. complete complying with standard specification and as directed by the departmental officers.
85	Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Plastering Sand) 10mm thick including mortar plasticizer at 200ml per 50Kg of cement used, hacking the surfaces and curing, etc., in all floors complying with standard specification and as directed by the departmental officers.
86	Supplying and applying of two coats of putty of 3mm thick over the exposed RCC surface of ceiling including finishing the joints smoothly with grinding machine and the surface shall be thoroughly cleaned out of dust and scrubbing. The surface shall then be allowed to dry for atleast 48 hours. It shall then be sand papered (waterproof abrasive sheet) to give a smooth and even surface. Any unevenness shall be made good by applying 1st coat of putty mixed with water on the entire surface including filling up the undulations and applying 2nd coat of putty after 6 hours of 1st coat of putty and then sand papering (water proof abrasive sheet) the same after it is dry and finishing the surface smoothly, etc., complete complying with standard specifications and as directed by the Departmental Officers. (The rates are inclusive of hire charges for grinding machine with wheel, cost of sand paper (water proof abrasive sheet), cost of putty blade, labour charges for grinding the joints and sand papering, two coats of putty, scrapping the putty area to level the surface smooth, etc.,complete. The putty should be got approved by the Executive Engineer before use on work.
87	Plastering with Cement Mortar 1:3 (One Cement and Three Plastering Sand) 12mm thick mixed with water proofing compound conforming to BIS at 2% by weight of cement used including mortar plasticizer at 200ml per 50Kg of cement used, finsihing, curing, etc., complete in all floors complying with standard specification and as directed by the departmental officers.
88	Plastering the surface of walls with Cement Mortar 1:3 (One cement and Three plastering sand), 20mm thick in all floors including mortar plasticizer at 200ml per 50Kg of cement used, curing etc., complete complying with standard specification and as directed by the departmental officers.
89	Providing the texture finish to the newly plastered wall with ready made texture putty with patterns at all levels including the cost of coating, labour charges and other incidental charges etc., complete as directed by the departmental officers.
90	Supplying and painting the walls with two coats of wall putty as instructed by the departmental officers including preparation of surface curing, etc., complete in all floors complying with standard specifications and as directed by the departmental officers. (The wall putty shall be got approved by the Executive Engineer before use of work).
91	Painting two coats of newly plastered wall surface with ready mixed plastic Interior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification and as directed by the departmental officers.
92	Polishing the teak wood shutters with two coats of Melamine polish to wood surface as per direction etc., complete should be got approved by the Executive Engineer before use on works.
93	Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with One coats of best approved first quality and colour of synthetic enamel paint over the priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification and as directed by the departmental officers. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)
94	supplying and fixing of Stainless Steel (Salem Stainless Steel) Door Frame (Box Section using Stainless Steel Plate of 1.60 mm thick) of size 100 mm x 60 mm with a rebate of 30 / 35 mm x 15 mm on one side of the frame including supplying and fixing dovetail splayed end stainless steel Hold fast etc.,for single leaf and double leaved door using pressed steel frame of size 105x60mm using mild sheet of 1.25mm thick (18gauge) special profile extruded section.The pressed steel frame should be as per IS4351/1976.The rate in inclusive of hold fasts and provision to aldrip tower bolt hinges and lock plate etc,with one coat of zinc chnomate yellow primer and filling the inside hallow portion with cement concrete 1:2:4 using 20mm HBG stone jelly etc,complete complying with standard specification and as directed by the departmental officers.
95	Supplying and fixing Teak Wood frames for doors Windows and Ventilators using required MS angles, flats and rods of approved design and as directed by the departmental officers including cost of MS Grills, labour charges and cost of one coat of red oxide primer with labour charges for priming coat etc. complete complying with standard specifiction.
96	T.W Scantlings Upto 2m
97	T.W Scantlings above 2m below 3m
98	Supplying and fixing solid core flush shutter of following type with thickness with necessary T.W. internal lipping alround conforming to IS 2202-1(1999) including cost of wind appliances and furniture fittings such as 3 Nos of SS 304 Grade Parliament Hinges of Size (125mm x 150mm) , 2 Nos 300x12mm aluminium tower bolt 1 No. 200x12mm aluminium tower bolts 1no. 250x16mm aluminium aldrops, 2 nos. 200mm ‘D’ type aluminium door handle and door stopper with bush etc., complete complying with standard specification and as directed by the departmental officers - Single leaf.
99	Supplying and fixing solid core flush shutter of following type with thickness with necessary T.W. internal lipping alround conforming to IS 2202-1(1999) including cost of wind appliances and furniture fittings such as 6 Nos of SS 304 Grade Parliament Hinges of Size (125mm x 150mm), 3 Nos. 300x12mm aluminium tower bolt 1 No. 200x12mm aluminium tower bolts 1no. 250x16mm aluminium aldrops, 3 nos. 200mm ‘D’ type aluminium door handle and door stopper with bush etc., complete complying with standard specification and as directed by the departmental officers - Double leaf.
100	supplying, hold fast of M.S flats of over all size of 330 x 50 x 6mm suitably folded to the required L shape have two end of lap of 50mm long each and overall length of the horizontal portion as 230mm & including making necessary grooves in two end laps to accomadate screws etc., complete.
101	Supplying and fixing in position of Teak wood door shutter using spl quality teak wood planks of 40mm thick panelled doors with required raw materials, Brass hinges, Brass tower bolt, ornamental Brass handles, Door stopper, Door closer, Brass aldrops and
102	Supply & fixing of WPC door shutter, extruded as a single core board with rigid WPC compound with the thickness of 25mm (+/- 1mm) & minimum Bulk Density of 550 KG/Cub.Mt. & shore hardness of 55. The door shall be a plain matt board as decided by the Engineer in-Charge of the department. The WPC door shall be fixed onto the Aluminium “G” type channel with Wheel and the door shall have 2 Hooks in SS, 2 Handles 4” in SS (Sliding door) etc., complete and as directed by the departmental officers.
103	UPVC Window Specification:Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work
104	Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI 1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 5.50mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work
105	Supplying and fixing Mild Steel grills for windows, ventilators etc.,complete complying with standard specifications and as directed by the departmental officers
106	Providing and fixing Acoustic wall panelling (equivalent to Armstrong) in channelled wood works perforated panels of width 192mm, thickness of 15mm and length of 2400mm or as per required by the Departmental Engineer made of a high density fibre board with minimum 725 kg / Cu.m. density substrate with a laminated facing as per the approved shade and finish and a melamine balancing layer on the reverse side. The boards shall have a special pattern where the visible surface has a \\"Heimhiliz\\" fluted perforationof 3mm width and 21mm of visible panel each.The edges of the panels shall be \\" tougue-and-grooved to receive special clips for installation. The back of the perforated panel shall have sound absorbing non woven acoustical fleese having NRC of 0.52. The panels shall be mounted on special aluminium splines using clips provided by armstrong and approved by the Engineer-in-Charges.
107	Supply and installation of Anutone (or) Euivalent Brand of Acoustical False Ceiling of subtex nubby,square edge, glass fibre core fully encapsulated ceiling tile of size 595x595x15mm having volume density 120Kgs / Cu.m, weight 1.8 / 2.4 / 3kg / Sq.m which is suspended by using 0.3mm thick skelet trelis T15 metal grid system. Skelet trelis T15metal grid system of 600x600mm module includes skelet WA15 W30 wall angle with unequal flanges of 15 / 19mm, length 3000mm, fixed along the perimeter of walls with the help of nylon sleeves and suitable fasteners at 300mm centers. Then suspend the skelet MT15 W36 MainT with flange width 15mm, height 32mm and length 3600mm, from the soffit slab with help of soffit cleat and wire rod with leveling spring clip at 1200mm centres. Skeler CT15 W12 Cross with flange width 15mm, height 26mm and length 1200mm is interlocked into the pre-cut slots in the Main T15 at 600mm centers in the perpendicular direction to the Main T15. Finally, the skelet CT15W06 Cross with flange width 15mm,height 26mm and length 600mm are interlocked into the precut slots in the CT15W12 CrossT in direction parallel to the Main T15 to result in 600 x 600mm module. The subtex nubby square edge of size 595 x 595 x15mm shall be placed into the grid size of 600 x 600mm. Ensure arrow marks behind the tiles are oriented in one direction to achieve uniform shade. The systems to achive noise reduction coefficient not less than 0.9 NRC, so as to have an neat appearance as directed by the departmental oficers. The cost includes, cost of materials, cost of labour, scafolding, transportation, conveyance, etc. complying to standard specification.
108	Structural Glazing:Providine and fixing structural glazing fabricated from roll formed sections made of galvanized steel colour coated ( Base steel as per IS 513 'D' quality,galvanized as per IS 277 with zinc of 120 grams / sq.). with total coated thickness of 0.72mm. The glass holding section made of 304 grade SS of 0.6mm thick Galvanized steel sections are to be used as stiffness inside the colour coated steel / powder coated sections as per the design requirement. Design calculations are made to suit wind pressure as given in IS 875. paint specification: Primer coat with epoxy primer of 5-7 microns thick finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer of 5-7 microns or powder coated with pure polyester powder upto 50-60 microns. Dimensions of section: The section should be of 37mmx 53mm for frame vertical,37x 53mm. for frame horizontal section and section for reinforced should be of 31x55mm. glass section should be of 37x 37mm for top & bottom grids in beetween should be of 37x18mm. Accessories: Brackets made of CRCA powder coated / electro plated should be used to fix vertical at top and bottom and vertical to slab as per site requirement. Polyurethane brackets should be used to connect horizontal section to vertical sections. Sillicon: Natural cure, with good UV resistance to be used.The above frame should be fixed to brick / concrete masonry by using nylon self-expanding caps and driving MS electro plated 80mm long screws into the caps through frames.Glass: 5mm reflectve Saint Gobain OR equivalent.
109	Providing and fixing of Aluminium Composite Panel (ACP) 4 sided having 50 x 25 x 1.50mm frame work vertical and horizontals out of specially designed extruded sections withstand wind pressure of 180 Kg/sq.m and fabricated fixed at all level elevation and heights. The extruded section cutting and fixing required space extruded section shall be of 6063 and alloy of BSH 9 confirming T is – 63400 rate shall included to fix the main frame with necessary clamps, fasteners, bolt nuts etc. The main frame of extruded section shall be of 22843 & 22739 (H9) grade conforming to BS 4174 (or) IS 8147. Rate shall included 4mm thick ACP sheet (0.25 + 3.5 + 0.25) fixing with spacer tape and the ACP sheet bounded with special type structural sealant of dow corning 789 or equivalent in dust free conditions the gaps between ACP sheet to be filed with whether sealant and backer rod or 12mm foam sheet to ensure water and air tightness in all complete complying with standard specification as directed by the departmental officer
110	Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between.The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc.complete
111	Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase near wet riser using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick will be provided with tubular supports made of 304L Grade Stainless Steel pipe of 25mm dia of 1.60mm thick welded to the railing. The supports will be grouted into the wall and provided with 93.00mm thick Stainless Steel circular base plate of 304 Grade. The rate shall included for grouting into concrete with necessary supporting arrangements the hand rail in floor polishing buffing, bonding, cutting, grinding, conveyance, welding charges, electrical charges, etc. complete
112	Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of \\"U\\" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification and as directed by the departmental officers.
113	UGT/OHT (inside) waterproofing with Anti microbial Coating Waterproofing: Providing and Applying CFTRI approved two component flexible polymer modified acrylic cementitious waterproofing coating with a mix ratio of (5 Liquid :7 Powder) to the RCC surface of the UGT/ OHT tank applied @ 2.2kg/m2 in 2 coats to achieve 1.2mm DFT, having Elongation at break >120% as per ASTM D 412, Tensile strength >1N/ mm2 as per ASTM D 412, Adhesion strength: 0.80N/ mm2 as per ASTM D 4541, crack bridging upto 2mm as per ASTM C 836. The finished cost to include surface preparation, making coving of 50 mm X 50mm at all right angles of wall Junction with Polymer Repair Mortar andlay 45 gsm glass fibre mesh over the angle fillet when the first coat in still wet, treatment of cracks completely as per specification. Followed by applying 15 mm thick dimensionally stable fibrous reinforced cementitious structural grade dual shrinkage Polymer Mortar on as protective plastering @ 29kg/m2. The material having Compressive strength of 38 MPa at 28 days as per EN 12190, Adhesive Bond Test, >1.5 Mpa as per EN 1542, followed by Water curing by sprinkling water for 3 times a day for 5- 7 days. Followed by applying two component, water-based food grade epoxy resin coating on inside surface of Potable water tank having anti- algae, antifungal, Non-toxic, hygiene cum damp-proof coating Certified by CFTRI as per 21 CFR 175 – 300 of US – FDA, having mixing Ratio (Base: Hardener: Water) – 1:1:1 to be applied @ 0.35 Kg/m2 in 2 coats. Ensure that this coating is applied over the protective plaster. The Waterproofing material shall have Specific Gravity: 1.2, Water vapor permeance: 244.48 g/m2/24 hrs, as per IS 7809/Pt 2/1977, Adhesion strength: 2 N/mm2 as per ASTM D 4541: 02. The finished cost to include surface preparation completely as per specification
114	Providing Polymer Coating (Water Proof Coating) for sunken portion of toilet with following specification and the surface shall be cleaned to remove all dust, foregin, matters lose materials or any other deposits of contamination by rubbing with wire brush. Slurry: Dry blend and polymer liquid blend shall be mixed into the desired ratio as per recommendation of the supplier. The mix shall be stirred thoroughly until no bubbles remain in the mix. Any lumps found in mix shall be removed. Apply first coat of polymer modified cementitious slurry by brush on wet cleaned surface. After drying, second coat shall be applied on the first coat as directed by the departmental officers etc. The rate inclusive of cost of materials and labour, etc., complete.
115	Supply and fixing of ABC STORED PRESSURE 6 kg capacityFire Extinguisher as per New IS No. 15683, complete withMono Ammonium Phosphate Powder, co2 gas , gun metalcap, squeeze gripe with nozzle, wall mounting bracket,pressure gauge, ISI mark , safety clip etc., as directed by thedepartment officers.
116	Supply and fixing of Water CO2 Stored pressure Type 9 litres capacity Fire Extinguisher as per new IS 15683 complete with control valve, gun metal cap, pressure gauge, operation sticker, discharge hose, wall mounting bracket, safety clip, etc., as Directed by the Departmental Officers.
117	Drilling of Borewells anywhere in Tamilnadu including transportation from one place to another with in Tamilnadu in alluvial soil sedimentary strata of clay and sand stone shale pebbles boulders etc. By first taking a pilot bore of 140 mm/150mm dia and then enlarging to required dia direct or reverse rotary mud circulation method using rotary rigs, fuel, labour and drilling bentonite and water required for drilling at site ( Site will be shown by the TWAD Board Officers) including construction of mud pit.
118	0 to 60m depth
119	60 to 90m depth
120	90 to 120m depth
121	120 to 150m
122	Reaming 140/150 mm dia pilot bore to 300mm dia bore as directed by the TWAD Board Officer.
123	0 to 60m depth
124	60 to 90m depth
125	90 to 120m depth
126	120 to 150m
127	Supply of 160 mm PVC Special Blue casing pipe of best approved quality etc complete as directed by the departmental officers. The pipe should got approved by the Executive Engineer before use on works.
128	Slotted pipe 160 mm Dia
129	Plain pipe 160mm Dia
130	Labour Charges for inserting PVC Casing pipes assembly (with slots or without slots) in the drilled hole including jointing the pipes with PVC Couplers with Cement paste etc., complete, supply and packing the annular space with pebbles of size and quality as approved by the executive engineers of TWAD Board
131	Charges for developing the Borewell with air compressor of 600 CFM capacity (Minimum 8 Hours) including transportation, labour and fuel charges for compressor as directed by TWAD Officers and conducting yield test by ‘V’ notch method.
132	Supplying and fixing HDPE pipe for sub-mergible pump in Bore well (class-5 1 MPa or 10 Kg / cm2 pressure) of best approved quality including welding wherever necessary etc., complete as directed by the Executive Engineer. The pipe should be got approved by the Executive Engineer before use on works.
133	40mm Dia
134	Supplying and fixing of 3 HP of approved brand Submersible Pump with accessories of starter, Main Switch, Panel Board etc. complete to suit the need. (The pump ste should be got approved by the EE before supply).
135	Supplying and fixing 6\\" PVC end cap (6Kg/cSq.m) for 6\\" dia borewell of best quality with ISI mark etc., complete
136	Supply, laying and run of 2 of 7/20 PVC sheathed Aluminium cable with polythene wire 10 gauge stay wire etc., complete as directed by the departmental officers.
137	Supplying and fixing of Nylon rope complete complying with standard specification and as directed by the departmental offices.
138	Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve / Wheel Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Executive Engineer before use on work.
139	25 mm dia G.M. Gate Valve
140	32mm dia G.M. Gate Valve
141	40 mm dia G.M. Gate Valve
142	Supplying and fixing in position 15mm dia brass CP screw down tap / Pillar tap / Swan neck tap (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works)
143	Supplying and fixing CP Bottle Trap including cost of all materials, labour etc., complete as directed by the departmental officers.
144	Supplying and fixing in position 15mm dia two way bibcock(heavy duty) with Health faucet of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works)
145	Supplying and fixing in position CP shower rose with CP stop cock arrangement of size 15mm dia inlet and 100mm outlet to the pipe line with necessary cutting, threading and jointing using shellac etc., complete complying with standard specification and as di- rected by the departmental officers (The CP shower rose should be got approved by the Executive Engineer before use on works).
146	Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC / Fibre Glass framed 600 x 450 x 5.5mm thick mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks)
147	Supplying and fixing approved best quality SS Towel Rack 600mm long with Lower Hanger of approved make with brackets of same materials including cost of teak wood plugs and CP screws, etc.,complete complying with standard specifications.(The tower rail should be got approved by Executive Engineer before use on works).
148	Supplying and fixing best approved best quality brass CP soap tray of size 150 x 150mm including cost of teak wood plugs, brass screws, etc., complete complying with standard specifications. (The soap tray should be got approved by Executive Engineer before use on works).
149	Supplying and fixing in position best quality and approved make Indian made white / colour glazed earthernware wash hand basin of size 550 x 400mm (with pedestal / without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia \\"B\\" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).
150	Supply and fixing in position of best Indian make white / colour glazed earthernware lipped mouth flat back urinal of best quality and approved make of size 430mm x 260mm x 350mm with GI pipe, 32mm dia bell mouth PVC connection and waste pipe, 15mm dia GI pipe of required length, 15mm dia GM wheel valve, 15mm dia brass nipple 2 Nos., and fixing the urinals in position with necessary TW plugs, clamps, screws, etc., includ- ing dismantling masnory and re-doing the same to the original condition, etc., including painting the pipe with two coats of best quality approved synthetic enamel paint over one coat of red oxide primer and checked without any leakage etc. complete complying with standard specifications and as directed by the departmental officers. (The urinal should be got approved by the Executive Engineer before use on works.)
151	Supplying and fixing in position white / colour glazed European Water Closet of best quality and approved make with 100 mm “P” or “S” trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings such as 15mm brass connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe including cost of 600mm length of 110mm dia PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition etc. complete complying with standard specifications. (The EWC and flushing tank wiht all accessories should be got approved by the Executive Enginer before use on works)
152	Supplying and fixing position CI Nahani Trap / Floor Trap of the following sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of crushed stone sandand five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works).
153	Nahani Trap of size 100 x 75mm with stainless steel gratings
154	Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level
155	75mm dia PVC soil waste pipe
156	110mm dia PVC soil waste pipe
157	160mm dia PVC soil waste pipe
158	Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re- doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works).
159	PVC Elbow
160	110mm dia
161	75mm dia
162	PVC Elbow with Door
163	110mm dia
164	75mm dia
165	PVC Tee
166	110mm dia
167	75mm dia
168	PVC Tee with Single Door
169	110mm dia
170	75mm dia
171	PVC \\"Y\\" with Single Door
172	110mm dia
173	75mm dia
174	PVC bend
175	110mm dia
176	75mm dia
177	Supplying and fixing in position PVC cowls of following dia of best approved quality conforming to BIS, etc., com- plete complying with standard specifications. (The PVC cowl should be got approved by the Executive Engineer before use on works).
178	75 mm dia
179	110 mm dia
180	Supplying, laying and jointing UPVC pipes of Class 6 (having working pressure of 12.50 kg/sq.cm) conforming to IS 4985- 2000 of approved quality and best variety of the following dia including cutting and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) in accordance with IS 7634-3 (2003) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works - Internal water supply above ground level.
181	20 mm dia UPVC Pipe
182	25 mm dia UPVC Pipe
183	32 mm dia UPVC Pipe
184	Supplying, laying and jointing UPVC pipes of Class 6 (having working pressure of 12.50 kg/sq.cm) conforming to IS 4985- 2000 of approved quality and best variety conforming to BIS of the following dia including cutting and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) in accordance with IS 7634-3 (2003) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works - External water supply above ground level / Below ground level.
185	Above GL
186	40 mm dia UPVC Pipe
187	Below GL
188	40 mm dia UPVC Pipe
189	Supplying UPVC Specials in water supply arrangements (both in internal and external water supply arrangements
190	UPVC Elbow
191	40 mm dia
192	32mm dia
193	25 mm dia
194	20 mm dia
195	UPVC Bend
196	40 mm dia
197	32mm dia
198	25 mm dia
199	20 mm dia
200	UPVC Tee
201	40 mm dia
202	32mm dia
203	25 mm dia
204	20 mm dia
205	UPVC Reducer
206	40x32mm dia
207	32x25mm dia
208	25 x 20 mm dia
209	20 x 15 mm dia
210	UPVC Reducer Elbow
211	40x32mm dia
212	32x25mm dia
213	25 x 20 mm dia
214	20 x 15 mm dia
215	UPVC Reducer Tee
216	40x32mm dia
217	32x25mm dia
218	25 x 20 mm dia
219	UPVC Hex Nipple
220	40 mm dia
221	32mm dia
222	25 mm dia
223	20 mm dia
224	UPVC Union
225	40 mm dia
226	32mm dia
227	25 mm dia
228	20 mm dia
229	Manufacturing, supplying and fixing Precast Reinforced Cement Concrete slabs of following thickness in RCC 1:2:4 (one cement, two crushed stone sand and four aggregates), using following HBGS jelly excluding cost of reinforcement steel in position but including cost of moulding charges, casting of slab, finishing, curing and fixing in position in all floors etc., complete complying with standard specification and as directed by the departmental officers.
230	75mm thick
231	Supplying and fixing in position of Steel fibre reinforced cement concrete (SFRC)manhole / inspection chamber cover slab with frame size 0.60x0.60m including necessary labour charges for fixing the frame in position over the cement mortar base and finishing the joints etc. complete as directed.
232	60cmx60cm
233	90cmx90cm
234	Supplying and fixing of PVC mould CI Steps of approved quality including dismantling masonry wherever necessary and redoing the damaged portion to original condition
235	Providing Anti-termite treatment to soil adjecent and under building foundation, plinth periphery of the building by application of chemicals of IS 6313 Part I to IV in stages to suit the progress of work consist as per the detailed specification as below. (Measurements taken for the plinth area for the purpose of payment) including breaking of termite mounds, making holes with crow bar, closing the holes after the treatment and including cost of chemicals, labour charges, transport and storing, etc., complete and as directed by the departmental officers.(The chemical should be got approved by Executive Engineer before use on work). Stage-1: Spraying anti-termite chemical solution for the foundation before laying concrete, in bottom and sides of foundation.Stage-2: Spraying anti-termite chemical solution to the grade beam level, spraying has to done for the grade beam, brick masonry contact with the back fill earth.Stage-3: Spraying anti-termite chemical solution on the sand for the flooring before laying the flooring concrete.This treatment has to be carried out on the sand filling by making holes with crow bar to a depth of 60cms and at 60cms intervals on both direction and at junction of wall and flooring thoroughout.Stage-4: Spraying anti-termite chemical solution alround building outside by making holes through bar before laying plinth protection and the holes to be closed after the treatment
236	Supplying and fillling 40mm.size HBGS jelly for dispersions trench as directed by the departmental officers.complying with standard specifications.
237	Supplying and fillling 20mm.size HBGS jelly for dispersions trench as directed by the departmental officers.complying with standard specifications.
238	Extra for vacuum dewatering in fresh concrete works 80 to 120mm thick by levelling with double framed screed vibrator finishing with power floater and power trowel and incidental works etc., complete and as directed by the department officers.
239	Supplyiong and fixing hume pipe 300mm dia and wall thick of50mm and laying proper position etc., complete and as directed by the department officers.
240	Supply and Erection of Hi- Tensile Structure CSC Brand 750GSM with complete fixtures. The main truss will be of 3\\" Dia Round pipe with 3mm Thickness, top and bottom in semi Arch shape. The Inner Vertical & cross Mull pipe be of 2\\" round dia.The purlin will be 2.5\\" round dia. Application of 1 coat of MRF Epoxy SPEP primer grey followed by two coats of MRF spectra polyurethane enamel top coat matching of IS - 800.With necessary G.I high tensile P.V.C coated rope , M.S powder coated cleat will be used as fixtures.
241	Providing the safe guard for the columns for 1m height with rubber corner guard of 4\\" x4\\" L-type colour od black and yellow approved quality etc.,complete and as directed by the department officers.
242	Supply and fixing of fire fighting application oblique type stainless steel Hydrant Valve of size 63mm dia with oblique type instantaneous coupling with rotating wheel to open and close the valve including MS flange of table “E”, bolts & nuts with washer as per IS 5290 at ring main around the building and wet riser inside the building including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary etc complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFEGUARD / SAFE GUARD / EQUIVALENT.
243	Supply, installation of fire fighting Application 180 degree swinging type, hose reel drum with 20mm dia braided thermoplastic hose of 30 metres long, so as to extend to necessary distance by self rolling spindle wheel including necessary 20mm dia ball valve and open and close spray nozzle, warm clip, etc., as per the standard pattern of any reputed make at every floor nearer to hydrant valve, including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary., etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFEGUARD / SAFE GUARD / EQUIVALENT.
244	Supply, and fixing in position of fire fighting Application Hose of 63mm dia of 15 metres length binded by copper wire with 63mm dia stainless steel male and female instantaneous fire fighting special coupling as per IS 901 as directed by the Departmental Officers. Near every hydrant points including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary etc complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR/ LIFEGUARD / SAFE GUARD / EQUIVALENT.
245	Supply, and fixing in position of fire fighting Application 63mm dia stainless steel short length Branch Pipe with hexagonal type spray nozzle of 15mm (or) 20mm jet bore. Near every hydrant points including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFEGUARD / SAFE GUARD / EQUIVALENT.
246	Supply of fire fighting Application MS Hose Box to keep two number of hoses and 1 No. of branch pipe with nozzle having proper glass window type double door with universe open key, painted inside white and outside Post Office Red. Near every hydrant point including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFEGUARD / SAFE GUARD / EQUIVALENT.
247	Supply and fixing nominal bore quartized bulb type sprinkler bulb 68 Deg C fast response Pendant type including GI collar for Nos sprinkler bulb, mounted in MS pipe line using suitable size MS threaded coupling, thread, shellac etc., as per standard methods and including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFEGUARD / SAFE GUARD / EQUIVALENT.
248	Supply, Installing, testing and commissioning of Stainless Steel Corrugated Flexible Braided Pipe (Hose) for dropping sprinklers below false ceiling. Pipe shall be 16 bar pressure rating and 1500mm long, 25mm dia with union / reducer, collar, clamps, etc. It shall have UL listed and FM approved.
249	Supplying and installing of approved type Rosette Plates (Recessed Type in Two Pieces) for sprinklers below false ceiling area. The Rosette shall be fabricated by MS plate of 2mm thick and the finish shall be powder coated and colour, as directed by the Departmental Officers.
250	Supply, erection, testing and commissioning of following MS C Class Heavy Duty Pipe as per IS 1239 to withstand a developing pressure of 10 kg. / sq.cm including necessary fittings like MS flange of table „E‟, elbows, reducers, gaskets, bolt, nuts with washers & joints as per standard method of arc welding, including one coat metal primer and two coat Post Office Red painting including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: JINDAL / EQUIVALENT.
251	150mm dia MS C Class Heavy
252	100 mm dia MS C Class Heavy
253	80mm dia MS C Class Heavy
254	50mm dia MS C Class Heavy
255	25mm dia MS C Class Heavy
256	Wrapping and Coating Anti-Corrosive Treatment for underground MS pipe having one coat of anti-corrosive metal primer, one layer of asphalt tar tape wound over the MS pipe as per standard methods as per standard specification as directed by the Departmental Officers.
257	150mm dia Wrapping and coating
258	100 mm dia Wrapping and Coating
259	Supply, erection, testing and commissioning of fire fighting 4 Way Fire Brigade Inlet with necessary gunmetal 63mm dia non return spring shutter arrangements, so that to control one way flow at the time of emergency water supply by fire and rescue service fire engine entry including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: KIARTAR / OMEX / EQUIVALENT.
260	Supply, erection, testing and commissioning of Air Release Valve of 20mm dia, so as to release airlock in 100 mm dia MS pipe at top most wet riser, including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: KARTAR / EQUIVALENT.
261	Supply, installation, testing and commissioning of Micro Processor based Conventional 12 Zone Fire Alarm Control Panel having the rating of 24 volt DC power supply, consisting 230 / 24 volt SMPS unit, 2 Nos. of 12 volt, 7 AH standby batteries, suitably mounted on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers.
262	Supply, installation, testing and commissioning of Conventional Smoke Detector suitably mounted on ceiling with MS junction box / false ceiling using fixing accessories like screws, plug, clamps, etc., as per standard methods and as directed by the Departmental Officers. (Make: Apollo / Equivalent)
263	Supply, installation, testing and commissioning of Manual Call Point (MCP) providing on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers. (Make: Ravel / Equivalent)
264	Supply, installation, testing and commissioning of Electronic Hooter / Sounder providing on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers (Make: Ravel / Equivalent)
265	Supply and laying of FRLS PVC insulated 2 core 1.5 sq.mm. Armoured Copper Cable on ceiling / wall using fixing accessories like screws, plug, clamps, etc., as per standard methods and as directed by the Departmental Officers.
266	Supply and fixing of stored pressure ABC (Mono Ammonium Phospate) Powder Type Fire Extinguisher of 6 kg. capacity as per IS:15683 with pressure gauge, discharge hose & control nozzle, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc, complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT / SAFETY FIRST / EQUIVALENT
267	Supply and fixing of Carbon-diOxide Gas Type 2 kg. capacity Fire Extinguisher as per New IS 15683, complete with control valve, discharge hose with horn, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary etc., complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT / SAFETY FIRST / EQUIVALENT
268	Providing, fixing pipe supports from columns / wall or suspenders from roof slab to suit various dia of pipes made out of GI / MS adjustable rods threaded for a sufficient length to adjust the height of support along with clamping arrangement for holding pipes of anchor fastening, arrangement design of hanger and should confirm with specification.
269	80mm dia Wall or Suspenders
270	50mm dia Wall or Suspenders
271	40mm dia Wall or Suspenders
272	Designing, Fabrication and fixing of Riser Supporting Clamp using 50 x 50 x 6 mm M.S 'L' angle, fabrication in line with Building Pillers,20 mm including the charges of cutting, Grinding, welding, Painting with one coat of Metal Primer and twoc Coats P.O Red Enamel paint, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete and as per standard specification and as directed by the Departmental Officers.
273	Supply, erection, testing and commissioning of following sizes of Heavy Duty Foot Valve including all accessories, such as, MS flange of table „E‟, gaskets, bolts & nuts, etc., installed at end of 150 / 200mm dia suction pipe line at sump including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary, etc., complete and as per standard specification and as directed by the Departmental Officers. Make: NORMEX / KARTAR / EQUIVALENT
274	150mm dia Heavy Duty Foot Valve
275	Supply, erection, testing and commissioning of 80mm dia Heavy Duty Foot Valve including necessary MS flange of table „E‟, gaskets, bolts & nuts, etc., installed at end of 80mm dia suction pipeline at sump as per the standard method and as directed by the Departmental Officers.
276	Supply, erection, testing and commissioning of cast iron body and bronze internal non-rising spindle sluice valve of sizes at required places to control the flow of water including necessary MS flange of table „E‟, gaskets, bolts & nuts including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: NORMEX / KARTAR / EQUIVALENT
277	150mm dia Sluice Valve
278	100 mm dia Sluice Valve
279	80mm dia Sluice Valve
280	Supply, erection, testing and commissioning of Cast iron body and gunmetal or stainless steel internal Non-return valve of following sizes to control one way flow of water to be installed pump room at delivery line and near overhead tank at terrace level near to jockey pump and motor including necessary MS flange of table „E‟, gaskets, bolts & nuts, etc. as per IS 5312 including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary, etc., complete as per standard specification and as directed by the Departmental Officers.
281	150 mm dia NRV
282	Supply, erection, testing and commissioning of cast iron body and gunmetal or stainless steel Internal Non-Return Valve of size of 80mm dia to control one way flow of water to be installed pump room at delivery line and near overhead tank at terrace level near to jockey pump and motor including necessary MS flange of table „E‟, gaskets, bolts & nuts, etc. as per IS 5312 including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary, etc., complete as per standard specification and as directed by the Departmental Officers.
283	Supply, erection, testing and commissioning of gunmetal Gate Valve of size 50mm dia size including necessary MS flange of table „E‟, gaskets, bolts & nuts etc., installed at pump house delivery line for the purpose of priming water to suction line including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: LEADER / EQUIVALENT.
284	Supply, erection, testing and commissioning of gunmetal Non-Return Valve of size 50mm dia including necessary MS flange of table „E‟, gaskets, bolts & nuts, etc., installed at pump house delivery line for the purpose of priming to suction line so that to control one way including conveying, fixing and incidental charges etc., complete as per standard specification and as directed by the Departmental Officers. Make: LEADER / EQUIVALENT.
285	Supply and providing 1000 litres capacity Priming Tank made up of PVC. Make: SINTEX / EQUIVALENT
286	Priming Tank mounted with the supporting arrangement fabricated using MS angle for the height of 3 metres from the floor level, inlet, outlet, and drain arrangements inside the fire fighting pump room, as directed by the Departmental Officers.
287	Supply and laying of following sizes of Armoured Aluminium Cables for electrical motor, control panel, pressure switch, jockey motor etc.. The rate inclusive of all incidental charges, necessary scaffolding and re- doing the dismantled portions to its original condition wherever found necessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: POLYCAB / PARACON / FINOLEX / EQUIVALENT.
288	3 core 185 sq.mm. armoured aluminium cable
289	3 core 10 sq.mm. armoured copper cable
290	10 core 2.5 sq.mm. armoured copper cable
291	2 core 2.5 sq.mm. armoured copper cable
292	Earthing arrangements with GI Earth Plate including charcoal and salt with necessary excavation in all soils and to full depth as may be required and masonry work, re-filling the sides of foundation with excavated earth as per the standard specification and as directed by the Departmental Officers.
293	Supply, erection, testing and commissioning of Pressure Gauge with 0 to 14 kg. range of reputed make with necessary valve, milling thread MS coupling fixed at delivery pipe line in pump house to read the developing pressure including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: H-GURU / ISI MAKE / EQUIVALENT.
294	Supply, erection, testing and commissioning of suitable Pressure Switch of reputed make line Indfos or Donfoss including necessary valves, couplings, etc., connected with electrical main control panel and setup at proper differential so as to auto start and auto stop the electrical motor, jockey motor including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary, etc., completed as per standard specification and as directed by the Departmental Officers. Make: DONFOSS / Indfos / ISI MAKE / EQUIVALENT.
295	Supplying, installation, testing and commissioning of fire fighting Electrical Control Panel of cubical construction, floor mounted type fabricated using CRCA sheet, compartmentalised with hinged lockable door dust and vermin proof, cable alley, inter connection having switch gears and accessories mounting and internal wiring, earth terminals, numberings, necessary metering protections and indications complete in all respect suitable for operation on 415volt, 3 phase, 50 Hz AC supply with enclosure protection class IP 54 and mounted with the followings.A. Common Panel in Fire Pump House (i). Incomera. 1 No. 600A TP & N SDFU with HRC fusesb. 1 set of 600A, 4 bar aluminium bus bar, 415 V, 50 HZ AC supplyc. 1 No. (0-500A) digital ammeter with selector switch & CTsd. 1 No. (0-500V) digital voltmeter with selector switch and control fusese. 3 Nos. phase indication lamp LED type with toggle switches with control fuses(ii). Outgoinga. Main Fire Pump400 A TPN SDFU with HRC fuses with sutable HP fully automatic starter /delta starter with over load protection, digital ammeter with built-in selector switch and suitable
296	CTs, current sensing type single phasing preventer complete with all accessories and internal wiring required for automatic operation, selector switch for auto / manual / OFF operation - 1 No.b. Jockey Pump125 A TPN SDFU with HRC fuses with suitable HP fully automatic starter / delta starter with over load protection, current sensing type single phasing preventer complete with all accessories and internal wiring required for automatic operation, selector switch for auto / manual operation - 1 No.c. Diesel Engine Control comprising of:1. Auto / manual selector switch and 3 attempt starting device, timers and relays as required, push buttons, start / stop in manual mode.2. Indication lamp for high / low lubricant oil pressure, high water temperature and engine ON indication.3. Battery charger suitable for 12V /24V DC with boost and tickle selector switch, 0-15V / 0-30V DC volt meter, 0-20A DC ammeter.4. All standard relays and accessories for automatic operation of diesel engine.5. The above combined panel mounted over MS channel fabricated frame with cement concrete platform, all other connection works carried out as per standard methods and including conveying, fixing and incidental charges, etc., complete as per standard specification and as directed by the Departmental Officers.
297	Supply, erection, testing and commissioning of 180 LPM, 70 metres Head Pressurization Pump with 10 HP electrical motor of Kirloskar make with suitable base frame including necessary vibration bad mounting etc., including conveying, fixing and incidental charges, etc., complete as per standard specification and as directed by the Departmental Officers. Make: KIRLOSKAR / EQUIVALENT.
298	Supply, erection, testing and commissioning of Fire Fighting Application Horizontal Centrifugal Type Pump Rated for 2280 LPM at 70 metres head with Electrical Motor of 60 HP of 415 volt 3 phase connection complete with base plate and accessories. (Make: Kirloskar or Equivalent). The rate inclusive of necessary vibration, bad mounting etc., as per standard method as directed by the Deparmental Officers.
299	Supply, installation, testing and commissioning of Diesel Engine Driven Main Fire Pump suitable for automatic operation and consisting of following and complete in all respects as required.a. End suction, top discharge centrifugal pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal to ensure a minimum pressure of 3.5 kg. / sq. cm at highest and farthest outlet at specified flow of 2280 LPM at 70m head conforming to IS 1520.b. 68 BHP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant BS & IS standard complete. Auto starting mechanism, 12 volts / 24 volts electric starting equipment like self motor, dynamo, solenoid switches etc.c. 110 litres capacity diesel tank mounted over stand fabricated using 25mm x 25mm x 6mm size MS angle, providing with level indicator, inlet port, outlet port, drain port and diesel return line port and fuel pre-filter, after filter etc. (Make: Kirloskar / Equivalent).
300	d. Exhaust system having flexible metallic mufler, 100 mm dia MS heavy pipe extended upto 1m, outside pump house duly insulated with 50mm thick glass wool with 1mm thick aluminium sheet cladding, residential silencer with necessory MS support arrangements from wall or ceiling as per site condition.e. Dash board consisting the instruments like temperature gauge, galvano type DC Ammeter, lubricant oil pressure gauge, ignition switch, emergency stop and all other protection equipment as per specification, stop seleneid for auto stop in the event of fault with audio indications, painted with post office red colour etc., as required.f. 12 V / 24 V storage battery, maintenance free tape, 180 AH rating, MS fabricated common base plate, coupling guard, foundation bolts etc., as required.g. Positioning the diesel engine driven fire pump over cement concrete foundation using suitable size anti-vibration mounting arrangement.All works carried out as per standard methods and as instructed by the manufacturer and as directed by the Departmental Officers. (Make: Kirloskar / Equivalent)
301	AC Room Table L2100 x D1050 x H750mm 25mm thk.Table Top E/B L2100mm X D1050mm - 1Nos 25mm thk. Vertical Leg E/B 1050mm X 750mm - 2Nos 18mm thk. Modesty 2100mm X 750mm - 1Nos Side Storage unit Size : L1200 x D450 x H750 mm Mobile Pedestal. Table Tops and legs made out of 25mm and modesty 18mm thick Commercial plywood with both side laminate finish, all exposed edges are Machine pressed Edgebanding finish. Mobile pedestals of size 400mm W x 450mm D x 650mm H completely made of 18mm thick Commercial plywood with laminate finished with 2mm thick PVC machine pressed edge banding. The rate includes labour for manufacturing, supply, transportation, etc.,
302	AC Room Chair with back in Moulded frame covered with breathable Mesh with HEAD REST in black, 18mm compressor plywood for seat with 3” thick high density foam covered with fireproof cloth, using synchro tilting mechanism in up and down adjustments, adjustable handle & bottom five frank chrome base with castor wheel finishing chairs. The rate includes labour for manufacturing, supply, transportation, etc.,
303	AC Room Visitor Chair with back in frame covered with breathable Mesh in black for back, with arm steel frame and leg chair 14 gauge CR round pipe legs, 18mm compressor plywood for seat with 3” thick high density foam covered with fireproof cloth, fixed arms, legs have nylon bushes. The rate includes labour for manufacturing, supply, transportation, etc.,
304	STO/DSTO/SUP Room Table L1500 x D750 x H750mm25mm thk.Table Top E/B L1500mm X D750mm - 1Nos25mm thk. Vertical Leg E/B 750mm X 750mm - 2Nos18mm thk. Modesty 1500mm X 750mm - 1NosSide Storage unit Size : L900 x D450 x H750 mmMobile Pedestal. Table Tops and legs made out of 25mm and modesty 18mm thick Commercial Plywood, all exposed edges are Machine pressed Edgebanding finish. 3 Draw mobile pedestals of size 400mm W x 450mm D x 650mm H completely made of 18mm Commercial Plywood finished with 2mm thick PVC machine pressed edge banding. The rate includes labour for manufacturing, supply, transportation, etc.,
305	STO/DSTO/SUP Room Chair with back in Moulded frame covered with breathable Mesh in black, 18mm compressor plywood for seat with 3” thick high density foam covered with fireproof cloth, using synchro tilting mechanism in up and down adjustments, adjustable handle & bottom five frank chrome base with castor wheel finishing chairs. The rate includes labour for manufacturing, supply, transportation, etc.,
306	STO/DSTO/SUP Room Visitor Chair with back in frame covered with breathable Mesh in black for back, with arm steel frame and leg chair 14 gauge CR round pipe legs, 18mm compressor plywood for seat with 3” thick high density foam covered with fireproof cloth, fixed arms, legs have nylon bushes. The rate includes labour for manufacturing, supply, transportation, etc.,
307	Waiting Area 3 Seater Chair Supply of 70 mica powder coated 3 seater capacity waiting chair of (L) 72\\"X (B) 24\\"X (H) 32\\", includings leges and back rest with two supporting legs and two arms at each ends. The seat bottom and back rest should be perforatted MS Fabricated sheets with smooth bends at all edges. The rate includes labour for manufacturing, supply, transportation, etc.,
308	JA, Asst. Workstation Linear 2 Seater with 75mm thick aluminium Partition , Top of size 4 X 2 and legs made out of 25mm and 18mm thick Prelam Particle board, all exposed edges are Machine pressed Edgebanding finish. 3 Draw mobile pedestals of size 400mm W x 450mm D x 650mm H completely made of 18mm Prelam Particle boards finished with 2mm thick PVC machine pressed edge banding finish. With Keyboard Tray. The rate includes labour for manufacturing, supply, transportation, etc.,
309	JA, Asst. Workstation Chair with back Moulded frame covered with breathable Mesh in black, 18mm compressor plywood for seat with 3” thick high density foam covered with fireproof cloth, using center tilting mechanism in up and down adjustments, fixed handle & bottom five frank chrome base with castor wheel finishing chairs. The rate includes labour for manufacturing, supply, transportation, etc.,
310	DC Room Table L2400 x D1050 x H750mm 25mm thk.Table Top E/B L2400mm X D1050mm - 1Nos 25mm thk. Vertical Leg E/B 1050mm X 750mm - 2Nos 18mm thk. Modesty 2400mm X 750mm - 1Nos Side Storage unit Size : L1200 x D450 x H750 mm Mobile Pedestal. Table Tops and legs made out of 25mm and modesty 18mm thick Commercial plywood with both side laminate finish, all exposed edges are Machine pressed Edgebanding finish. Mobile pedestals of size 400mm W x 450mm D x 650mm H completely made of 18mm thick Commercial plywood with laminate finished with 2mm thick PVC machine pressed edge banding. The rate includes labour for manufacturing, supply, transportation, etc.,
311	AC Room Table L2100 x D1050 x H750mm 25mm thk.Table Top E/B L2100mm X D1050mm - 1Nos 25mm thk. Vertical Leg E/B 1050mm X 750mm - 2Nos 18mm thk. Modesty 2100mm X 750mm - 1Nos Side Storage unit Size : L1200 x D450 x H750 mm Mobile Pedestal. Table Tops and legs made out of 25mm and modesty 18mm thick Commercial plywood with both side laminate finish, all exposed edges are Machine pressed Edgebanding finish. Mobile pedestals of size 400mm W x 450mm D x 650mm H completely made of 18mm thick Commercial plywood with laminate finished with 2mm thick PVC machine pressed edge banding. The rate includes labour for manufacturing, supply, transportation, etc.,
312	AC,DC Room Executive Chair with back in Moulded frame covered with breathable Mesh with HEAD REST in black, 18mm compressor plywood for seat with 3” thick high density foam covered with fireproof cloth, using synchro tilting mechanism in up and down adjustments, adjustable handle & bottom five frank chrome base with castor wheel finishing chairs. The rate includes labour for manufacturing, supply, transportation, etc.,
313	AC,DC Room Visitor Chair with back in frame covered with breathable Mesh in black for back, with arm steel frame and leg chair 14 gauge CR round pipe legs, 18mm compressor plywood for seat with 3” thick high density foam covered with fireproof cloth, fixed arms, legs have nylon bushes. The rate includes labour for manufacturing, supply, transportation, etc.,
314	Waiting Area Sofa 2 seater Providing sofa of with basic Silver Wood framework. The seat have flat type High Density cushions placed on the seat, back rest with fireproof cloth or leatherride. Bottom Legs with Floor Adjustable bush model sofa. The rate includes labour for manufacturing, supply, transportation, etc.,
315	Waiting Area Sofa 3 seater Providing sofa of with basic Silver Wood framework. The seat have flat type High Density cushions placed on the seat, back rest with fireproof cloth or leatherride. Bottom Legs with Floor Adjustable bush model sofa. The rate includes labour for manufacturing, supply, transportation, etc.,
316	Waiting Area Center Teapoy of Size 3X1½ Teakwood with Melamine polish. The rate includes labour for manufacturing, supply, transportation, etc.,
317	Waiting Area Corner Teapoy of Size 2½X2½ Teakwood with Melamine polish. The rate includes labour for manufacturing, supply, transportation, etc.,
318	Lunch Room 4 Seater Table of size 4’x2’-6\\" with 18mm granite top with half round nosing edges with 16 gauge SS pipe leg, floor adjustments bushes at the bottom . As Per Sample Approved Model. The rate includes labour for manufacturing supply, transportation, etc.,
319	Lunch Room 9 Seater Table of size 4’x2’-6\\" with 18mm granite top with half round nosing edges with 16 gauge SS pipe leg, floor adjustments bushes at the bottom . As Per Sample Approved Model. The rate includes labour for manufacturing supply, transportation, etc.,
320	Dining Chair Nilkamal model with PVC fixed mould seat and back and bottom with 1\\" SS leg with floor adjustment nylon bushes. The rate includes labour for manufacturing,supply, transportation, etc.,
321	Waiting Area 3 Seater Chair Supply of 70 mica powder coated 3 seater capacity waiting chair of (L) 72\\"X (B) 24\\"X (H) 32\\", includings leges and back rest with two supporting legs and two arms at each ends. The seat bottom and back rest should be perforatted MS Fabricated sheets with smooth bends at all edges. The rate includes labour for manufacturing, supply, transportation, etc.,
322	Waiting Area 4 Seater Chair Supply of 70 mica powder coated 4 seater capacity waiting chair includings leges and back rest with two supporting legs and two arms at each ends. The seat bottom and back rest should be perforatted MS Fabricated sheets with smooth bends at all edges. The rate includes labour for manufacturing, supply, transportation, etc.,
323	STO/DSTO Room Table L1500 x D750 x H750mm25mm thk.Table Top E/B L1500mm X D750mm - 1Nos25mm thk. Vertical Leg E/B 750mm X 750mm - 2Nos18mm thk. Modesty 1500mm X 750mm - 1NosSide Storage unit Size : L900 x D450 x H750 mmMobile Pedestal. Table Tops and legs made out of 25mm and modesty 18mm thick Commercial Plywood, all exposed edges are Machine pressed Edgebanding finish. 3 Draw mobile pedestals of size 400mm W x 450mm D x 650mm H completely made of 18mm Commercial Plywood finished with 2mm thick PVC machine pressed edge banding. The rate includes labour for manufacturing, supply, transportation, etc.,
324	STO/DSTO Room Chair with back in Moulded frame covered with breathable Mesh in black, 18mm compressor plywood for seat with 3” thick high density foam covered with fireproof cloth, using synchro tilting mechanism in up and down adjustments, adjustable handle & bottom five frank chrome base with castor wheel finishing chairs. The rate includes labour for manufacturing, supply, transportation, etc.,
325	STO Room Visitor Chair with back in frame covered with breathable Mesh in black for back, with arm steel frame and leg chair 14 gauge CR round pipe legs, 18mm compressor plywood for seat with 3” thick high density foam covered with fireproof cloth, fixed arms, legs have nylon bushes. The rate includes labour for manufacturing, supply, transportation, etc.,
326	JA,Asst., Typ., Workstation Linear 5 Seater with 75mm thick aluminium Partition , Top of size 4 X 2 and legs made out of 25mm and 18mm thick Prelam Particle board, all exposed edges are Machine pressed Edgebanding finish. 3 Draw mobile pedestals of size 400mm W x 450mm D x 650mm H completely made of 18mm Prelam Particle boards finished with 2mm thick PVC machine pressed edge banding finish. With Keyboard Tray. The rate includes labour for manufacturing, supply, transportation, etc.,
327	JA,Asst., Typ., Workstation Linear 3 Seater with 75mm thick aluminium Partition , Top of size 4 X 2 and legs made out of 25mm and 18mm thick Prelam Particle board, all exposed edges are Machine pressed Edgebanding finish. 3 Draw mobile pedestals of size 400mm W x 450mm D x 650mm H completely made of 18mm Prelam Particle boards finished with 2mm thick PVC machine pressed edge banding finish. With Keyboard Tray. The rate includes labour for manufacturing, supply, transportation, etc.,
328	JA,Asst., Typ., Workstation Linear 2 Seater with 75mm thick aluminium Partition , Top of size 4 X 2 and legs made out of 25mm and 18mm thick Prelam Particle board, all exposed edges are Machine pressed Edgebanding finish. 3 Draw mobile pedestals of size 400mm W x 450mm D x 650mm H completely made of 18mm Prelam Particle boards finished with 2mm thick PVC machine pressed edge banding finish. With Keyboard Tray. The rate includes labour for manufacturing, supply, transportation, etc.,
329	JA,Asst., Typ., Workstation Chair with back Moulded frame covered with breathable Mesh in black, 18mm compressor plywood for seat with 3” thick high density foam covered with fireproof cloth, using center tilting mechanism in up and down adjustments, fixed handle & bottom five frank chrome base with castor wheel finishing chairs. The rate includes labour for manufacturing, supply, transportation, etc.,
330	JC Room Table L3000 x D1050 x H750mm 25mm thk.Table Top E/B L3000mm X D1050mm - 1Nos 25mm thk. Vertical Leg E/B 1050mm X 750mm - 2Nos 18mm thk. Modesty 3000mm X 750mm - 1Nos Side Storage unit Size : L1200 x D450 x H750 mm Mobile Pedestal. Table Tops and legs made out of 25mm and modesty 18mm thick Commercial plywood with both side laminate finish, all exposed edges are Machine pressed Edgebanding finish. Mobile pedestals of size 400mm W x 450mm D x 650mm H completely made of 18mm thick Commercial plywood with laminate finished with 2mm thick PVC machine pressed edge banding. The rate includes labour for manufacturing, supply, transportation, etc.,
331	JC Room Chair Back : 3/4' round pipe frame covered with 40 Density cushion with selected Upholstery, Seat: 3/4' round pipe with spring and 2\\" PU Molded Foam with and selected Upholstery covered synchrony Tilting Facility, Hydraulic gas Lift, Stainless steel Base, PU arms Nylon caster Wheels. The rate includes cost of all materials, fabrication, transports and other incidental charges, including providing in the position as directed by departmental officers.
332	JC Room Visitor Chair with Seat and Back cushion covered with Cloth, arms and legs are SS Chrome Plate Steel Frame, nylon netted cloth for handle cover, legs have nylon bushes. The rate includes labour for manufacturing, supply, transportation, etc.,
333	JC Room Sofa Three Seater Providing sofa of with basic Silver Wood framework. The seat have High Density cushions placed on the seat, back rest with fireproof cloth or leatherride. Bottom Legs with Floor Adjustable bush model sofa. The rate includes labour for manufacturing, supply, transportation, etc.,
334	JC Room Sofa Two Seater Providing sofa of with basic Silver Wood framework. The seat have High Density cushions placed on the seat, back rest with fireproof cloth or leatherride. Bottom Legs with Floor Adjustable bush model sofa. The rate includes labour for manufacturing, supply, transportation, etc.,
335	JC Room Center Teapoy of Size 3X1½ Teakwood with Melamine polish. The rate includes labour for manufacturing, supply, transportation, etc.,
336	JC Room Corner Teapoy of Size 2½X2½ Teakwood with Melamine polish. The rate includes labour for manufacturing, supply, transportation, etc.,
337	DC Room Table L2400 x D1050 x H750mm 25mm thk.Table Top E/B L2400mm X D1050mm - 1Nos 25mm thk. Vertical Leg E/B 1050mm X 750mm - 2Nos 18mm thk. Modesty 2400mm X 750mm - 1Nos Side Storage unit Size : L1200 x D450 x H750 mm Mobile Pedestal. Table Tops and legs made out of 25mm and modesty 18mm thick Commercial plywood with both side laminate finish, all exposed edges are Machine pressed Edgebanding finish. Mobile pedestals of size 400mm W x 450mm D x 650mm H completely made of 18mm thick Commercial plywood with laminate finished with 2mm thick PVC machine pressed edge banding. The rate includes labour for manufacturing, supply, transportation, etc.,
338	AC Room Table L2100 x D1050 x H750mm 25mm thk.Table Top E/B L2100mm X D1050mm - 1Nos 25mm thk. Vertical Leg E/B 1050mm X 750mm - 2Nos 18mm thk. Modesty 2100mm X 750mm - 1Nos Side Storage unit Size : L1200 x D450 x H750 mm Mobile Pedestal. Table Tops and legs made out of 25mm and modesty 18mm thick Commercial plywood with both side laminate finish, all exposed edges are Machine pressed Edgebanding finish. Mobile pedestals of size 400mm W x 450mm D x 650mm H completely made of 18mm thick Commercial plywood with laminate finished with 2mm thick PVC machine pressed edge banding. The rate includes labour for manufacturing, supply, transportation, etc.,
339	AC, DC Room Chair with back in Moulded frame covered with breathable Mesh with HEAD REST in black, 18mm compressor plywood for seat with 3” thick high density foam covered with fireproof cloth, using synchro tilting mechanism in up and down adjustments, adjustable handle & bottom five frank chrome base with castor wheel finishing chairs. The rate includes labour for manufacturing, supply, transportation, etc.,
340	AC, DC Room Visitor Chair with back in frame covered with breathable Mesh in black for back, with arm steel frame and leg chair 14 gauge CR round pipe legs, 18mm compressor plywood for seat with 3” thick high density foam covered with fireproof cloth, fixed arms, legs have nylon bushes. The rate includes labour for manufacturing, supply, transportation, etc.,
341	Meeting Room Table L15000 x D1800 x H750mmTable tops and legs made out of 25mm and modesty made out of 18mm thick Commercial Plywood with both side laminate finish, all exposed edges are Machine pressed Edgebanding finish. The rate includes labour for manufacturing supply, transportation, etc.,
342	Meeting Room Chair with back in frame covered with breathable Mesh in black for back, with arm steel frame and leg chair 14 gauge CR round pipe legs, 18mm compressor plywood for seat with 3” thick high density foam covered with fireproof cloth, fixed arms, legs have nylon bushes. The rate includes labour for manufacturing, supply, transportation, etc.,
343	Meeting Room Back Row Visitor Chair with arm steel frame and leg chair with cushion, 3'' 18 gauge CR round pipe legs, seat and back high density molded cushion, upholstery fire proof cloth, arms are PU soft pad, legs have nylon bushes. The rate includes labour for manufacturing, supply, transportation, etc.,
344	Waiting Area Sofa 2 seater Providing sofa of with basic Silver Wood framework. The seat have flat type High Density cushions placed on the seat, back rest with fireproof cloth or leatherride. Bottom Legs with Floor Adjustable bush model sofa. The rate includes labour for manufacturing, supply, transportation, etc.,
345	Waiting Area Sofa 3 seater Providing sofa of with basic Silver Wood framework. The seat have flat type High Density cushions placed on the seat, back rest with fireproof cloth or leatherride. Bottom Legs with Floor Adjustable bush model sofa. The rate includes labour for manufacturing, supply, transportation, etc.,
346	Waiting Area Center Teapoy of Size 3X1½ Teakwood with Melamine polish. The rate includes labour for manufacturing, supply, transportation, etc.,
347	Waiting Area Corner Teapoy of Size 2½X2½ Teakwood with Melamine polish. The rate includes labour for manufacturing, supply, transportation, etc.,
348	Waiting Area 3 Seater Chair Supply of 70 mica powder coated 3 seater capacity waiting chair of (L) 72\\"X (B) 24\\"X (H) 32\\", includings leges and back rest with two supporting legs and two arms at each ends. The seat bottom and back rest should be perforatted MS Fabricated sheets with smooth bends at all edges. The rate includes labour for manufacturing, supply, transportation, etc.,
349	Waiting Area 4 Seater Chair Supply of 70 mica powder coated 4 seater capacity waiting chair includings leges and back rest with two supporting legs and two arms at each ends. The seat bottom and back rest should be perforatted MS Fabricated sheets with smooth bends at all edges. The rate includes labour for manufacturing, supply, transportation, etc.,
350	Waiting Area 2 Seater Chair Supply of 70 mica powder coated 4 seater capacity waiting chair includings leges and back rest with two supporting legs and two arms at each ends. The seat bottom and back rest should be perforatted MS Fabricated sheets with smooth bends at all edges. The rate includes labour for manufacturing, supply, transportation, etc.,
351	STO, STENO Room Table L1500 x D750 x H750mm25mm thk.Table Top E/B L1500mm X D750mm - 1Nos25mm thk. Vertical Leg E/B 750mm X 750mm - 2Nos18mm thk. Modesty 1500mm X 750mm - 1NosSide Storage unit Size : L900 x D450 x H750 mmMobile Pedestal. Table Tops and legs made out of 25mm and modesty 18mm thick Commercial Plywood, all exposed edges are Machine pressed Edgebanding finish. 3 Draw mobile pedestals of size 400mm W x 450mm D x 650mm H completely made of 18mm Commercial Plywood finished with 2mm thick PVC machine pressed edge banding. The rate includes labour for manufacturing, supply, transportation, etc.,
352	STO, STENO Room Chair with back in Moulded frame covered with breathable Mesh in black, 18mm compressor plywood for seat with 3” thick high density foam covered with fireproof cloth, using synchro tilting mechanism in up and down adjustments, adjustable handle & bottom five frank chrome base with castor wheel finishing chairs. The rate includes labour for manufacturing, supply, transportation, etc.,
353	STO, STENO Room Visitor Chair with back in frame covered with breathable Mesh in black for back, with arm steel frame and leg chair 14 gauge CR round pipe legs, 18mm compressor plywood for seat with 3” thick high density foam covered with fireproof cloth, fixed arms, legs have nylon bushes. The rate includes labour for manufacturing, supply, transportation, etc.,
354	DSTO Room Table L1500 x D750 x H750mm 25mm thk.Table Top E/B L1500mm X D750mm - 1Nos 25mm thk. Vertical Leg E/B 750mmx750mm - 2Nos 18mm thk. Modesty 1500mm X 750mm - 1Nos Side Storage unit Size : L900 x D450 x H750 mmMobile Pedestal. Table Tops and legs made out of 25mm and modesty 18mm thick Commercial Plywood, all exposed edges are Machine pressed Edgebanding finish. 3 Draw mobile pedestals of size 400mm W x 450mm D x 650mm H completely made of 18mm Commercial Plywood finished with 2mm thick PVC machine pressed edge banding. The rate includes labour for manufacturing, supply, transportation, etc.,
355	DSTO Room Chair with back in Moulded frame covered with breathable Mesh in black, 18mm compressor plywood for seat with 3” thick high density foam covered with fireproof cloth, using synchro tilting mechanism in up and down adjustments, adjustable handle & bottom five frank chrome base with castor wheel finishing chairs. The rate includes labour for manufacturing, supply, transportation, etc.,
356	JA,Asst., Workstation Linear 5 Seater with 75mm thick aluminium Partition , Top of size 4 X 2 and legs made out of 25mm and 18mm thick Prelam Particle board, all exposed edges are Machine pressed Edgebanding finish. 3 Draw mobile pedestals of size 400mm W x 450mm D x 650mm H completely made of 18mm Prelam Particle boards finished with 2mm thick PVC machine pressed edge banding finish. With Keyboard Tray. The rate includes labour for manufacturing, supply, transportation, etc.,
357	RC Room Workstation Linear 3 Seater with 75mm thick aluminium Partition , Top of size 4 X 2 and legs made out of 25mm and 18mm thick Prelam Particle board, all exposed edges are Machine pressed Edgebanding finish. 3 Draw mobile pedestals of size 400mm W x 450mm D x 650mm H completely made of 18mm Prelam Particle boards finished with 2mm thick PVC machine pressed edge banding finish. With Keyboard Tray. The rate includes labour for manufacturing, supply, transportation, etc.,
358	Typ. Room Workstation Linear 2 Seater B/B with 75mm thick aluminium Partition , Top of size 4 X 2 and legs made out of 25mm and 18mm thick Prelam Particle board, all exposed edges are Machine pressed Edgebanding finish. 3 Draw mobile pedestals of size 400mm W x 450mm D x 650mm H completely made of 18mm Prelam Particle boards finished with 2mm thick PVC machine pressed edge banding finish. With Keyboard Tray. The rate includes labour for manufacturing, supply, transportation, etc.,
359	Typ. Room Workstation Linear 3 Seater with 75mm thick aluminium Partition , Top of size 4 X 2 and legs made out of 25mm and 18mm thick Prelam Particle board, all exposed edges are Machine pressed Edgebanding finish. 3 Draw mobile pedestals of size 400mm W x 450mm D x 650mm H completely made of 18mm Prelam Particle boards finished with 2mm thick PVC machine pressed edge banding finish. With Keyboard Tray. The rate includes labour for manufacturing, supply, transportation, etc.,
360	Workstation Chair with back Moulded frame covered with breathable Mesh in black, 18mm compressor plywood for seat with 3” thick high density foam covered with fireproof cloth, using center tilting mechanism in up and down adjustments, fixed handle & bottom five frank chrome base with castor wheel finishing chairs. The rate includes labour for manufacturing, supply, transportation, etc.,
361	Reception Table Size : 9 x 9 tops and legs made out of 25mm and 18mm thick Commercial Plywood with both side laminate finish, all exposed edges are Machine pressed Edgebanding finish. As Per Sample Approved Model.The rate includes labour for manufacturing, supply,transportation, etc
362	Reception Chair with back Moulded frame covered with breathable Mesh in black, 18mm compressor plywood for seat with 3” thick high density foam covered with fireproof cloth, using center tilting mechanism in up and down adjustments, fixed handle & bottom five frank chrome base with castor wheel finishing chairs. The rate includes labour for manufacturing, supply, transportation, etc.,
363	JC Room Table L3000 x D1050 x H750mm 25mm thk.Table Top E/B L3000mm X D1050mm - 1Nos 25mm thk. Vertical Leg E/B 1050mm X 750mm - 2Nos 18mm thk. Modesty 3000mm X 750mm - 1Nos Side Storage unit Size : L1200 x D450 x H750 mm Mobile Pedestal. Table Tops and legs made out of 25mm and modesty 18mm thick Commercial plywood with both side laminate finish, all exposed edges are Machine pressed Edgebanding finish. Mobile pedestals of size 400mm W x 450mm D x 650mm H completely made of 18mm thick Commercial plywood with laminate finished with 2mm thick PVC machine pressed edge banding. The rate includes labour for manufacturing, supply, transportation, etc.,
364	JC Room Chair Back : 3/4' round pipe frame covered with 40 Density cushion with selected Upholstery, Seat: 3/4' round pipe with spring and 2\\" PU Molded Foam with and selected Upholstery covered synchrony Tilting Facility, Hydraulic gas Lift, Stainless steel Base, PU arms Nylon caster Wheels. The rate includes cost of all materials, fabrication, transports and other incidental charges, including providing in the position as directed by departmental officers.
365	JC Room Visitor Chair with Seat and Back cushion covered with Cloth, arms and legs are SS Chrome Plate Steel Frame, nylon netted cloth for handle cover, legs have nylon bushes. The rate includes labour for manufacturing, supply, transportation, etc.,
366	JC Room Sofa Three Seater Providing sofa of with basic Silver Wood framework. The seat have High Density cushions placed on the seat, back rest with fireproof cloth or leatherride. Bottom Legs with Floor Adjustable bush model sofa. The rate includes labour for manufacturing, supply, transportation, etc.,
367	JC Room Sofa Two Seater Providing sofa of with basic Silver Wood framework. The seat have High Density cushions placed on the seat, back rest with fireproof cloth or leatherride. Bottom Legs with Floor Adjustable bush model sofa. The rate includes labour for manufacturing, supply, transportation, etc.,
368	JC Room Center Teapoy of Size 3X1½ Teakwood with Melamine polish. The rate includes labour for manufacturing, supply, transportation, etc.,
369	JC Room Corner Teapoy of Size 2½X2½ Teakwood with Melamine polish. The rate includes labour for manufacturing, supply, transportation, etc.,
370	DC Room Table L2400 x D1050 x H750mm 25mm thk.Table Top E/B L2400mm X D1050mm - 1Nos 25mm thk. Vertical Leg E/B 1050mm X 750mm - 2Nos 18mm thk. Modesty 2400mm X 750mm - 1Nos Side Storage unit Size : L1200 x D450 x H750 mm Mobile Pedestal. Table Tops and legs made out of 25mm and modesty 18mm thick Commercial plywood with both side laminate finish, all exposed edges are Machine pressed Edgebanding finish. Mobile pedestals of size 400mm W x 450mm D x 650mm H completely made of 18mm thick Commercial plywood with laminate finished with 2mm thick PVC machine pressed edge banding. The rate includes labour for manufacturing, supply, transportation, etc.,
371	AC Room Table L2100 x D1050 x H750mm 25mm thk.Table Top E/B L2100mm X D1050mm - 1Nos 25mm thk. Vertical Leg E/B 1050mm X 750mm - 2Nos 18mm thk. Modesty 2100mm X 750mm - 1Nos Side Storage unit Size : L1200 x D450 x H750 mm Mobile Pedestal. Table Tops and legs made out of 25mm and modesty 18mm thick Commercial plywood with both side laminate finish, all exposed edges are Machine pressed Edgebanding finish. Mobile pedestals of size 400mm W x 450mm D x 650mm H completely made of 18mm thick Commercial plywood with laminate finished with 2mm thick PVC machine pressed edge banding. The rate includes labour for manufacturing, supply, transportation, etc.,
372	AC, DC Room Chair with back in Moulded frame covered with breathable Mesh with HEAD REST in black, 18mm compressor plywood for seat with 3” thick high density foam covered with fireproof cloth, using synchro tilting mechanism in up and down adjustments, adjustable handle & bottom five frank chrome base with castor wheel finishing chairs. The rate includes labour for manufacturing, supply, transportation, etc.,
373	AC, DC Room Visitor Chair with back in frame covered with breathable Mesh in black for back, with arm steel frame and leg chair 14 gauge CR round pipe legs, 18mm compressor plywood for seat with 3” thick high density foam covered with fireproof cloth, fixed arms, legs have nylon bushes. The rate includes labour for manufacturing, supply, transportation, etc.,
374	Meeting Room Table L15000 x D1800 x H750mmTable tops and legs made out of 25mm and modesty made out of 18mm thick Commercial Plywood with both side laminate finish, all exposed edges are Machine pressed Edgebanding finish. The rate includes labour for manufacturing supply, transportation, etc.,
375	Meeting Room Chair with back in frame covered with breathable Mesh in black for back, with arm steel frame and leg chair 14 gauge CR round pipe legs, 18mm compressor plywood for seat with 3” thick high density foam covered with fireproof cloth, fixed arms, legs have nylon bushes. The rate includes labour for manufacturing, supply, transportation, etc.,
376	Meeting Room Back Row Visitor Chair with arm steel frame and leg chair with cushion, 3'' 18 gauge CR round pipe legs, seat and back high density molded cushion, upholstery fire proof cloth, arms are PU soft pad, legs have nylon bushes. The rate includes labour for manufacturing, supply, transportation, etc.,
377	Waiting Area Sofa 2 seater Providing sofa of with basic Silver Wood framework. The seat have flat type High Density cushions placed on the seat, back rest with fireproof cloth or leatherride. Bottom Legs with Floor Adjustable bush model sofa. The rate includes labour for manufacturing, supply, transportation, etc.,
378	Waiting Area Sofa 3 seater Providing sofa of with basic Silver Wood framework. The seat have flat type High Density cushions placed on the seat, back rest with fireproof cloth or leatherride. Bottom Legs with Floor Adjustable bush model sofa. The rate includes labour for manufacturing, supply, transportation, etc.,
379	Waiting Area Center Teapoy of Size 3X1½ Teakwood with Melamine polish. The rate includes labour for manufacturing, supply, transportation, etc.,
380	Waiting Area Corner Teapoy of Size 2½X2½ Teakwood with Melamine polish. The rate includes labour for manufacturing, supply, transportation, etc.,
381	Waiting Area 3 Seater Chair Supply of 70 mica powder coated 3 seater capacity waiting chair of (L) 72\\"X (B) 24\\"X (H) 32\\", includings leges and back rest with two supporting legs and two arms at each ends. The seat bottom and back rest should be perforatted MS Fabricated sheets with smooth bends at all edges. The rate includes labour for manufacturing, supply, transportation, etc.,
382	Waiting Area 4 Seater Chair Supply of 70 mica powder coated 4 seater capacity waiting chair includings leges and back rest with two supporting legs and two arms at each ends. The seat bottom and back rest should be perforatted MS Fabricated sheets with smooth bends at all edges. The rate includes labour for manufacturing, supply, transportation, etc.,
383	STO/DSTO Room Table L1500 x D750 x H750mm25mm thk.Table Top E/B L1500mm X D750mm - 1Nos25mm thk. Vertical Leg E/B 750mm X 750mm - 2Nos18mm thk. Modesty 1500mm X 750mm - 1NosSide Storage unit Size : L900 x D450 x H750 mmMobile Pedestal. Table Tops and legs made out of 25mm and modesty 18mm thick Commercial Plywood, all exposed edges are Machine pressed Edgebanding finish. 3 Draw mobile pedestals of size 400mm W x 450mm D x 650mm H completely made of 18mm Commercial Plywood finished with 2mm thick PVC machine pressed edge banding. The rate includes labour for manufacturing, supply, transportation, etc.,
384	STO/DSTO Room Chair with back in Moulded frame covered with breathable Mesh in black, 18mm compressor plywood for seat with 3” thick high density foam covered with fireproof cloth, using synchro tilting mechanism in up and down adjustments, adjustable handle & bottom five frank chrome base with castor wheel finishing chairs. The rate includes labour for manufacturing, supply, transportation, etc.,
385	STO Room Visitor Chair with back in frame covered with breathable Mesh in black for back, with arm steel frame and leg chair 14 gauge CR round pipe legs, 18mm compressor plywood for seat with 3” thick high density foam covered with fireproof cloth, fixed arms, legs have nylon bushes. The rate includes labour for manufacturing, supply, transportation, etc.,
386	JA, Asst., Room Workstation Linear 5 Seater with 75mm thick aluminium Partition , Top of size 4 X 2 and legs made out of 25mm and 18mm thick Prelam Particle board, all exposed edges are Machine pressed Edgebanding finish. 3 Draw mobile pedestals of size 400mm W x 450mm D x 650mm H completely made of 18mm Prelam Particle boards finished with 2mm thick PVC machine pressed edge banding finish. With Keyboard Tray. The rate includes labour for manufacturing, supply, transportation, etc.,
387	JA, Asst., Typ., Room Workstation Linear 4 Seater with 75mm thick aluminium Partition , Top of size 4 X 2 and legs made out of 25mm and 18mm thick Prelam Particle board, all exposed edges are Machine pressed Edgebanding finish. 3 Draw mobile pedestals of size 400mm W x 450mm D x 650mm H completely made of 18mm Prelam Particle boards finished with 2mm thick PVC machine pressed edge banding finish. With Keyboard Tray. The rate includes labour for manufacturing, supply, transportation, etc.,
388	JA, Asst., Typ., Room Workstation Linear 3 Seater with 75mm thick aluminium Partition , Top of size 4 X 2 and legs made out of 25mm and 18mm thick Prelam Particle board, all exposed edges are Machine pressed Edgebanding finish. 3 Draw mobile pedestals of size 400mm W x 450mm D x 650mm H completely made of 18mm Prelam Particle boards finished with 2mm thick PVC machine pressed edge banding finish. With Keyboard Tray. The rate includes labour for manufacturing, supply, transportation, etc.,
389	JA, Asst., Typ., Room Workstation Linear 4 Seater B/B with 75mm thick aluminium Partition , Top of size 4 X 2 and legs made out of 25mm and 18mm thick Prelam Particle board, all exposed edges are Machine pressed Edgebanding finish. 3 Draw mobile pedestals of size 400mm W x 450mm D x 650mm H completely made of 18mm Prelam Particle boards finished with 2mm thick PVC machine pressed edge banding finish. With Keyboard Tray. The rate includes labour for manufacturing, supply, transportation, etc.,
390	Workstation Chair with back Moulded frame covered with breathable Mesh in black, 18mm compressor plywood for seat with 3” thick high density foam covered with fireproof cloth, using center tilting mechanism in up and down adjustments, fixed handle & bottom five frank chrome base with castor wheel finishing chairs. The rate includes labour for manufacturing, supply, transportation, etc.,
391	AC Room Table L2100 x D1050 x H750mm 25mm thk.Table Top E/B L2100mm X D1050mm - 1Nos 25mm thk. Vertical Leg E/B 1050mm X 750mm - 2Nos 18mm thk. Modesty 2100mm X 750mm - 1Nos Side Storage unit Size : L1200 x D450 x H750 mm Mobile Pedestal. Table Tops and legs made out of 25mm and modesty 18mm thick Commercial plywood with both side laminate finish, all exposed edges are Machine pressed Edgebanding finish. Mobile pedestals of size 400mm W x 450mm D x 650mm H completely made of 18mm thick Commercial plywood with laminate finished with 2mm thick PVC machine pressed edge banding. The rate includes labour for manufacturing, supply, transportation, etc.,
392	AC Room Chair with back in Moulded frame covered with breathable Mesh with HEAD REST in black, 18mm compressor plywood for seat with 3” thick high density foam covered with fireproof cloth, using synchro tilting mechanism in up and down adjustments, adjustable handle & bottom five frank chrome base with castor wheel finishing chairs. The rate includes labour for manufacturing, supply, transportation, etc.,
393	AC Room Visitor Chair with back in frame covered with breathable Mesh in black for back, with arm steel frame and leg chair 14 gauge CR round pipe legs, 18mm compressor plywood for seat with 3” thick high density foam covered with fireproof cloth, fixed arms, legs have nylon bushes. The rate includes labour for manufacturing, supply, transportation, etc.,
394	STO/DSTO/Sup., Room Table L1500 x D750 x H750mm 25mm thk.Table Top E/B L1500mm X D750mm - 1Nos25mm thk. Vertical Leg E/B 750mm X 750mm - 2Nos 18mm thk. Modesty 1500mm X 750mm - 1Nos Side Storage unit Size : L900 x D450 x H750 mm Mobile Pedestal. Table Tops and legs made out of 25mm and modesty 18mm thick Commercial Plywood, all exposed edges are Machine pressed Edgebanding finish. 3 Draw mobile pedestals of size 400mm W x 450mm D x 650mm H completely made of 18mm Commercial Plywood finished with 2mm thick PVC machine pressed edge banding. The rate includes labour for manufacturing, supply, transportation, etc.,
395	STO/DSTO/Sup., Room Chair with back in Moulded frame covered with breathable Mesh in black, 18mm compressor plywood for seat with 3” thick high density foam covered with fireproof cloth, using synchro tilting mechanism in up and down adjustments, adjustable handle & bottom five frank chrome base with castor wheel finishing chairs. The rate includes labour for manufacturing, supply, transportation, etc.,
396	STO/DSTO/Sup., Room Visitor Chair with back in frame covered with breathable Mesh in black for back, with arm steel frame and leg chair 14 gauge CR round pipe legs, 18mm compressor plywood for seat with 3” thick high density foam covered with fireproof cloth, fixed arms, legs have nylon bushes. The rate includes labour for manufacturing, supply, transportation, etc.,
397	Conference Hall Chair Supply of Teak Wood Chair made out of good quality teakwood finished with melamine polish and legs with bushes. The Chair seat & back high density cushion shall be covered with upholestry cloth finish. The rate includes cost of material, labour for manufacturing, supply, transportation to mentioned location etc., complete as per the standards and as directed by the departmental officers.
398	Conference Hall Stage Table 8 X 2.5 Tops and legs made out of 25mm and 18mm thick Commercial Plywood, with both side laminate finish, all exposed edges are Machine pressed Edgebanding finish. The rate includes labour for manufacturing, supply, transportation, etc.,
399	Conference Hall Stage Chair Supply of Teak Wood VIP Chair made out of good quality teakwood finished with melamine polish with Kadasal leg with ornamental finish for legs with bushes. The Chair seat & back high density cushion shall be covered with upholestry cloth finish. The rate includes cost of material, labour for manufacturing, supply, transportation to mentioned location etc., complete as per the standards and as directed by the departmental officers.
400	Workstation Linear 4 Seater with 75mm thick aluminium Partition , Top of size 4 X 2 and legs made out of 25mm and 18mm thick Prelam Particle board, all exposed edges are Machine pressed Edgebanding finish. 3 Draw mobile pedestals of size 400mm W x 450mm D x 650mm H completely made of 18mm Prelam Particle boards finished with 2mm thick PVC machine pressed edge banding finish. With Keyboard Tray. The rate includes labour for manufacturing, supply, transportation, etc.,
401	Workstation Linear 2 Seater with 75mm thick aluminium Partition , Top of size 4 X 2 and legs made out of 25mm and 18mm thick Prelam Particle board, all exposed edges are Machine pressed Edgebanding finish. 3 Draw mobile pedestals of size 400mm W x 450mm D x 650mm H completely made of 18mm Prelam Particle boards finished with 2mm thick PVC machine pressed edge banding finish. With Keyboard Tray. The rate includes labour for manufacturing, supply, transportation, etc.,
402	Workstation Linear 2 Seater B/B with 75mm thick aluminium Partition , Top of size 4 X 2 and legs made out of 25mm and 18mm thick Prelam Particle board, all exposed edges are Machine pressed Edgebanding finish. 3 Draw mobile pedestals of size 400mm W x 450mm D x 650mm H completely made of 18mm Prelam Particle boards finished with 2mm thick PVC machine pressed edge banding finish. With Keyboard Tray. The rate includes labour for manufacturing, supply, transportation, etc.,
403	Workstation Linear 3 Seater B/B with 75mm thick aluminium Partition , Top of size 4 X 2 and legs made out of 25mm and 18mm thick Prelam Particle board, all exposed edges are Machine pressed Edgebanding finish. 3 Draw mobile pedestals of size 400mm W x 450mm D x 650mm H completely made of 18mm Prelam Particle boards finished with 2mm thick PVC machine pressed edge banding finish. With Keyboard Tray. The rate includes labour for manufacturing, supply, transportation, etc.,
404	Workstation Chair with back Moulded frame covered with breathable Mesh in black, 18mm compressor plywood for seat with 3” thick high density foam covered with fireproof cloth, using center tilting mechanism in up and down adjustments, fixed handle & bottom five frank chrome base with castor wheel finishing chairs. The rate includes labour for manufacturing, supply, transportation, etc.,
405	Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS FRLS copper conductor of 1100 V grade in suitable heavy gauge MS conduit pipe on wall and ceiling with MS accessories with Module GI switch box in flush wall with 6A one way module switch with module front plate with painting of Suitable colour with continuous earth wire connection of 1.5 sq.mm copper wire for Open MS conduit Light point / fan point (for electronic regulator) ( 6 points / Coil) Higher End
406	Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS FRLS copper conductor of 1100 V grade in suitable heavy gauge MS conduit pipe on wall and ceiling with MS accessories with suitable Module GI switch box on wall with 1 no. 6A one way module switch and 1 no. 6A 3/2 pin module socket with module front plate with painting of Suitable colour with continuous earth wire connection of 1.5 sq.mm copper wire for Open MS conduit Plug point ( 8 points / Coil) Higher End
407	Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (5 points / Coil) Higher End )
408	Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (6 points / Coil) Higher End
409	Supply and fixing of WT bulk head fitting with guard suitable with 7W / 9W LED bulb
410	Supply and fixing of 100W LED High bay Light Fitting for Portico with fan clamp with side plates and cross arm of size 450mm (18\\") with PVC unsheathed copper leads in existing terminal.
411	Supply and fixing of Single box type 4'20 W LED fitting with TW round blocks on wall or ceiling with 20W LED tube with PVC unsheathed Copper leads from terminal to the fitting.
412	Supply and fixing of Single box type 4'20 W LED fitting with TW round blocks with 600mm conduit pipe suspension from the ceiling with 20W LED tube with PVC unsheathed Copper leads from terminal to the fitting.
413	Supply and fixing of 18W LED square type Recessed fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting.
414	Supply and fixing of 48W LED street light fitting with LED (Higher end) with 32mm dia. GI pipe (class B) with 1 no.32 mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting.
415	Supply and fixing of IP65 post top LED fitting on existing gate light pillar and at the bottom of the pillar supply and fixing of MS box of 30cmx20cmx10cm with angle iron frame work with door and lock and key arrangements and supply and fixing of 1no 6A SP MCB inside the MS box with PVC unsheathed leads and painting of suitable color.
416	Supply and fixing of 1200mm (48\\") sweep AC ceiling fan High speed complete with 2 module 100W fan step regulator (Higher end) with 600 mm down rod with fan clamp with side plates and cross arm of size 450mm (18\\")
417	Supply and fixing of 450 mm (18 inch) wall mount, Oscillating type fan with aerodynamically designed semi transparent PP three blades for noise free operation with in built Speed regulator with necessary accessories with connections complete (Crompton/Orient/Eq.)
418	Supply and fixing of 300mm (12\\") sweep (lightduty) AC exhaust fan complete with necessary wall opening and making good of the wall with louvers shutters arrangements
419	Supply and fixing of AC/DC 76 mm buzzer/call bell suitable for 230 volts 50 c/s single phase Ac supply on suitable TW board with push switch.
420	Supply and fixing of 3nos.6A two module 5 pin socket , 3 nos. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End
421	Supply and fixing of 1 no.6/16A two module socket , 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End
422	Supply and fixing of 20Amps DP Plug and Socket in sheet enclosure with 32A DP MCB in flush with wall with earth connection (For AC Plug) (Legrand / Hager make).
423	Supply and fixing of 32A DP MCB in flush with sheet enclosure in flush with wall with earth connection [Legrand (MDS) / Hager (L&T) make]
424	Supply and fixing of 63A FP MCB in flush with sheet enclosure in flush with wall with earth connection [Legrand (MDS) / Hager (L&T) make]
425	Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A DP MCB Isolator as incoming and 3 nos. 32A DP MCB as outgoing in flush with wall with earth connection only. Higher End
426	Supply and fixing of 12 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 10 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End.
427	Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 6 nos. 6A to 32A SP MCB as outgoing in wall with earth connection only. Higher End
428	Supply and fixing of 7 segment 4 way TPN MCB sheet steel distribution board (Higher end) with metal / acrylic door cover flush type /surface type fitted with busbars and neutral links with single / three phase MCB outgoings and seperate 4 way provision for accomodating one no. 4 pole incoming MCB / Isolator and another seperate 4 way provision for accomodating one no. 4 pole ELCB / RCD (totally 4 ways in one segment) (3x 4 ways in each segment) and seperate provision for MCB / Isolators ( totally 12 nos.) for sub incomers in 3 segments with lable holder and provison for taking up cable for size not less than 35 sq.mm. with the following in flush with wall with earth connection only.
429	Supply and fixing of 4 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 100A 4P MCB switch as incoming, 12 Nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End
430	Supply and fixing of 4 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P MCB switch as incoming and 12 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End
431	Supply and Run of 2 of 2.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection of 2.5 sq.mm copper wire and making good of the concealed portion
432	Supply and Run of 2 of 4 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection by 4 sq.mm. PVC insulated SC unsheathed FRLS copper wire and making good of the concealed portion.
433	Supply and Run of 2 of 6 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection by 6 sq.mm. PVC insulated SC unsheathed FRLS copper wire and making good of the concealed portion.
434	Supply and Run of 4 of 6 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 6 sq.mm copper wire and making good of the concealed position.
435	Supply and Run of 4 of 10 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 10 sq.mm copper wire and making good of the concealed position.
436	Supply and fixing of dust and vermin proof cubical type 250A Capacity 3 Chamber LTCT meter Panel of size 3ft. Length X 4ft. Height X 1ft. Depth made of 16SWG sheet steel with door with rubber beading, with lock and bolt with sealing hole arrangements with angle iron support comprising of five compartments one for 3 phase energy meter with base plate with view glass, one for bus bar arrangements with 3nos 32 x 6 mm insulated tinned Cu bus bar for 3 phases and 1no 25 x 6 mm Neutral with synthetic moulded compound support, one for 13 way Test Terminal Block Front
437	Connection type with 4Nos. 2A HRC fuse base with fuse links, one for 3Nos. of 250A HRC DIN type Fuse Base and Fuse links with 150A/5A Cts of PVC insulation type from reputed make and another compartment for Cable entry with danger board with superscribing of Cable size, powder coated painting of one coat of redoxide and two coat of synthetic enamel grey paind as specified the departmental officials and with necessary 6mm thickness hylem sheet separation for energy meter hamber, test terminal block with 2A fuses chamber and 250A Fuse units and CT Coils chamber, with 2.5 & 4 Sq.mm PVC insulated Cu wires for interconnections, with transporting, loading, unloading, commissioning & testing.
438	Supply, erection, testing and commissioning of 400A capacity vermin dust proof cubical of 14 SWG line quality MS sheet steel enclosures for accommodating the 400A TPN busbar (rising main) of size 40 x 6 mm copper busbar for 3 phases and neutral and 2 nos earth bus bar copper of size 25 x 3 mm and with provision for accommodating incomer 400A Main Switch and tap off switches including copper inter connect to the stretch of height building.
439	Supply, erection, testing and commissioning of 250A capacity vermin dust proof cubical of 14 SWG line quality MS sheet steel enclosures for accommodating the 250A TPN busbar (rising main) of size 32 x 6 mm copper busbar for 3 phases and neutral and 2 nos earth bus bar copper of size 25 x 3 mm and with provision for accommodating incomer 250A Main Switch and tap off switches including copper inter connect to the stretch of height building.
440	Supply and fixing of 400A TPN Incomer Switch in suitable enclosures from 400A rising mains for necessary interconnection with copper bus bar if size 32 x 6 mm for Phases and Neutral with proper neutral link and 25 x 3 mm copper bus bar for Earth.
441	Supply and fixing of 250A TPN Incomer Switch in suitable enclosures from 250A rising mains for necessary interconnection with copper bus bar if size 32 x 6 mm for Phases and Neutral with proper neutral link and 25 x 3 mm copper bus bar for Earth.
442	125 A Lighting panel-Supply, Erection, testing and commissioning of 125 A capacity dust and vermin proof horizontal type cubical panel board made up of 16 SWG CRCA Sheet with supply and fixing of the following interior switches with HRC fuse links arranged horizontally with horizontal busbar chamber and cable chambers. 1. 125A TPN switch disconnector fuse unit interior only with HRC fuses double break-1 Nos.2. 100A TPN switch disconnector fuse unit interior only with HRC fuses double break-1 No. 3. 63A TPN switch disconnector fuse unit interior only with HRC fuses double break-4 Nos.
443	The busbar chamber shall consist of 4 Nos 33mm x 6mm copper flat for phases and neutral and interconnection between incoming switch and buses. The 38mm x 6mm copper flat for interconnection between TPN switches to buses. 38mm x 6mm copper flat buses shall be mounted on SMC busbar insulator at proper and sufficient interval as per IE rules. The busbar chamber shall be segregated from the adjacent chamber. The heat shrinkable sleeves shall be provided for busbar with colour code. The 25mm x 3mm copper flat for double earth connection for all incoming and outgoing switches are to be provided in this panel. The panel shall have powder coated painting of approved colours, approved by the department officers. The danger board shall be fixed at front of panel board. The panel shall be mounted on MS base channel provided all round at the bottom of the panel. The whole arrangements shall be erected on a Masonary pedestal to be constructed with suitable foundation with bolts and nuts such that the lowest SDF unit fuse handle is at a height of 0.75m from the ground level. (note: All SDF unit shall be of L&T / Siemens make).
444	250A Power panel-Supply, fabrication, erection and commissioning of 250A dust and vermin proof floor mounting cubical type panel board of size 6ft x 5ft x 1.5ft made up of 16 SWG CRCA sheet steel for outer body and stiffness and doors, switch supports respectively and supply and fixing of following interior mounting switches with centre bus bar chamber and vertical covers on both sides of the bus bar chamber at the extreme ends side and confirming to IS specification. All the main switches should be L&T / Siemens make only interconnection of switches with busbar chamber.
445	(1) 250A TPN switch disconnector interior only with HRC fuses double break as incomer - 1 Nos (L&T/Siemens) (1) 250A TPN switch disconnector interior only with HRC fuses double break as incomer - 1 Nos (L&T/Siemens) (2) 100A TPN switch disconnector interior only with HRC fuses double break as outgoing - 4 Nos (L&T/Siemens) (3) 63A TPN switch disconnector interior only with HRC fuses double break as outgoing - 4 Nos (L&T/Siemens) A separate chamber on top of one side should be built with multi function digital volt meter, ammeter and frequency meter with one set of LED pilot lamp set with fuse base, top with 10A HRC link for 3 phase (Siemns) the bus will have 2 Nos 1\\" x ⅛\\" earth bus must be run all around the panel to provide double earth connection to the cubical switches cable glands, cable adopter box etc.The bus should be mounted on synthetic moulded compound bus support at equal interval as per IS specifications. The switch should be separated from the bus by 6mm thick hylum sheet separators, and properly earthed by tinned solid copper flat as I.E rules CEIG sepecifications. The panel should be painted with two high quality enamel paint over one coat of red oxide primer, the cable size, capacity of switch, location etc., should be marked with white paint and 2 Nos. metallic danger board affixed complete with mounting on base channel 3\\"x1½\\"x½\\" iron frame work support complete.
446	Supply and fixing of 125A TPN Tap off Switch in suitable enclosures from 250A rising mains for necessary interconnection with copper bus bar if size 25 x 6 mm for Phases and Neutral with proper neutral link and 25 x 3 mm copper bus bar for Earth.
447	Supply and fixing of 250A TPN Tap off Switch in suitable enclosures from 400A rising mains for necessary interconnection with copper bus bar if size 25 x 3 mm for Phases and Neutral with proper neutral link and 25 x 3 mm copper bus bar for Earth.
448	Supply and clarnping of 3 1/2 x 95 sq.mm PVC LTUG armoured LTUG cable on post or on wall with MS Clamps.
449	Supply and fixing of brass cable gland for 3 1/2 x 95 sq.mm LTUG armoured cable with earth connection.
450	Supply and providing cable end termination of 3 1/2 x 95 sqmm PVC LTUG Aluminium armoured cable withnecessary aluminium cable sockets by crimping etc. with electrical connection comple)
451	Supply, Installation, Testing and commissioning of 10 KVA UPS system 3 phase input and Single phase output and as per the detailed specification enclosed, Sealed Maintenance free batteries to support 10 KVA for 1 hrs backup complete with intercell connectors & copper cables, battery stand made out of powder coated MS Angles with adeguate support to carry the load of the batteries. The vendor shall submit dimensional GA drawing of complete UPS/ Inverter system battery rack with batteries, Service panel and battery bank calculation.
452	Design, Engineering, Supply, Fabrication, Erection, Testing, commissioning and handing over of 1 no 16 persons passenger Gearless lift with Machine room as per the following specifications including taxes and duties. 1.Location: CTO Office Chengalpattu2.No of lift: 1 No3.Type of lift: passenger4.Capacity of lift: 16 persons / 1088 Kgs5.Speed: 1m / sec6.Type of drive: V3F drive with enhanced ride comfort and near zero level functions 7.No of floors: GF + 5 Floor8.Total travel: 21.6 mtrs9.Leveling accuracy: high level accuracy with smooth and jerk free stopping 10. Construction of CAR: No 4 hardened sheet high quality stainless steel car and hand rail granite flooring and Perspex false ceiling.11. Position of machine: directly above the lift well.12. No of landing service: one in the front side-6 no’s13. No. of car entrance: one in the front side only14. Car entrance door: power operated automatic V3F drive center opening sliding SS door15. Landing entrance door: power operated V3F drive center opening sliding SS door with provision for emergency exit key at all landings.
453	16.Lift well Size : 2100 mm (wide)x 2500 mm (depth)as per ISI 14665(part1) 2000 17.Lift pit depth:1600 mm 18. Car size: 2000 mm (width) x 1100 mm (depth) as per IS 14665 (part 1 )2000, 19. Car clear opening: 900 mm wide x 2000 mm height as per IS 14665 (part 1)200020. Power supply: 400 / 440 v three phase 50 Hz AC supply for power and 230 V 50 Hz single phase power supply for light.21.Control: micro computer (micro processor):based simplex collective control with / without attendant 22. Car fittings: LED lighting with 1 no 300 mm sweep cabin fan.23. Lift well: Already Existing24. Induction: UP / DOWN digital direction and position indicator for all landings and inside the car.25.Emergency alarm bell: battery operated bell to be provided with automatic charging device 26.Emergency light: battery operated light to be provided with automatic charging device27.Fire mans switch: to be provided at the GF28. Minor builder works: to be provided by the lift contractor.29. Scaffoldings: to be provided by the lift contractor.30. Sill angles and fascia plates: SS to be provided by the lift contractor.
454	31. Steel for lift machinery: to be provided by the lift contractor.32. Servicing and maintenance: Comprehensive servicing and maintenance of lifts for further period of two years beyond free warranty period of one year from the date of commissioning of lifts will be paid at the rate of 5% of capital cost of lift.33. Automatic rescue device: to facilitate the landing of the nearest floor at the time of power failure this shall consist of suitable battery system with charger inverter under voltage protection system etc. complete with all accessories.34. Provision for intercom with phone: to be provided by the lift contractor.35.Lift license: preparation of drawings payment of charges to CEIG and insurance policy if any and obtaining CEIG approval for the lift as per lift act should be done by the lift contractor 36. Floor position announcer: to be provided by the lift contractor.37.Special features a) Infra red door sensor with full height screenb) Full width rear panel mirrorc)Tubular SS hand rail in car d) Stainless steel signal features e) Vandal proof SS button with SS coverf) SS door frames for landing doors g) V3F door operator h) Call register signal
455	i) Stainless steel fascia plates for car operating panel and landing fixtures j) Steel ladder for lift machine roomk) On / off switch for fan and light l) Over load warning indicator with audio announcerm)Voltage stabilizer for control circuitsn)Braille button o) Granite flooring provided by the lift contractor 39.Over speed governor phase failure and phase reversal relay alarm bell T guide brackets for car and counter weight rubber padding under the winding unit motor of adequate capacity signal reduction worm gear electromagnetic brake with compression springs car safety gears buffers electro mechanical locks emergency key side supporting angles motor over load protection devices final limit switch main suspension ropes counter weight lifting joist for mounting the machineries 40. Guarantee: guarantee at least for one year for the material and workman ship of equipments should be offered by the lift contractor.41. Site testing in accordance with IS 14665 should be carried out at the time of handing over to the user department 42. Supply operation and maintenance manual and necessary tools for operation and a set of Spare parts required for one year.
456	Supply and clamping of 31/2 x 25 sq.mm PVC LTUG armoured LTUG cable on post or on wall with MS Clamps
457	Supply and fixing of brass cable gland for 3½ x 25 sqmm PVC armoured LTUG cable with earth connection.
458	Supply and providing cable end termination of 3 1/2 x 25 sqmm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc. with electrical connection complete
459	Supply of 1 No 160 KVA diesel generator set with AMF Panel 0.8 P.F, 3 ph, 415v / 420 volts, 50 c/s, 1500 RPM as detailed belowEngine :Water cooled diesel engine suitable for generator application with a shaft output of suitable 214 BHP at 1500 RPM under NTP conditions as per BSS 5414-ISO 10000 The engine shall comprise the following standard scope of supply : (Make Kirloskar)1) Dry type Air cleaner.2) Expansion bellow.3) Radiator, radiator fan and mounting.4) Air to air charge cooler.5) Exhaust gas turbo charger.6) Lube oil cooler and lube oil filter.7) Fuel filter (pre and micro)8) In-Line mono-block fuel injection pump with governor and fuel feed pump.9) Electronic governor.10) 24V battery charging alternator.11) 24V Volt electric starter motor.12) Engine test certificate.13) Residential Muffler.14) Fly wheel with Housing15) Exhaust silencer.Safety system of Engine :The engines shall trip for the following conditions with Visual alarm device.1. Low lubricating oil pressure.2. High water temperature.
460	3. Vee - belt failure and over speed.The following visual indicator should also be provide Low Battery Indication.The Engine should be capable of providing 10% over load for one hour for every 11 hours continuous running at full load.Alternator :Alternator capacity of 160 KVA/128KW, AC 3 phase, 50HZ, 415 Volts, 0.8 P.F, 4 wire self excited, self regulated designed to run at 1500 RPM under NTS conditions conforming to BSS 5000 / IS 13364 (part-II) 1992 to be coupled directly to the Diesel engine and test certificate. (Make : Kirloskar Green /Crompton Greaves / Equivalent) ACOUSTIC ENCLOSURE :Acoustic enclosure shall be powder coated and fabricated of 16 SWG CRCA MS sheet. The silent canopy shall be of nut bolt type construction. Critical processes of punching are done on CNC machines to maintain dimensional accuracy of hole within 0.1mm powder coating done after seven-tank surface preparation process of sheet metal. Canopy panel and doors shall have inside lining of FIRE-RETARDANT 64kg/m density mineral wool of 100mm thickness as acoustic material. Four hinged doors shall be provided to canopy. The average sound level at 1 Mt. distance shall be less than 75DBA average or as per CPCB norms.
461	SURFACE TREATMENT - PAINTING The enclosure shall be suitably treated for degreasing, de-rusting and posphating. The canopies are passed through seven-tank treatment thoroughly.ADDITIONAL FEATURES OF CANOPIESCanopy fabricated on CNC machines with dimensional accuracy of 0.1mm so as to increase its durability. Special designed supporting rips / structures are used in canopies so as to give studiness and to reduce the vibrations of the DG sets if any.WORLD CLASS COOLING PACKAGE :Canopies shall have cooling package for which it can also perform at 45 deg c / ambient temperature. No grounding required on the ground, only a level surface capable of with standing the DG weight. Lifting hooks shall be provided for the acoustic enclosure, which should be unloaded independently of the DG set. The Gen set frame shall also be provided with hooks for unloading.TEMPERATURE RISE INSIDE THE CANOPY :Canopies shall be designed so as to maintain the temperature difference between ambient and air inlet at cleaner within the enclosure well with in 5-7 deg centigrade.BASE FRAME :Base frame should be fabricated in sheet metal.
462	The base frame is rugged in construction and designed for mounting engine and brush less alternator closely coupled, with cross members mounted on AVM. The base frame shall have provision for mounting of acoustic enclosure on it. The supply of Gen set includes loading, unloading and transportation charges.FUEL TANK :230 Lts. Integral Built in Fuel Tank shall be fabricated out of 14 SWG CRCA MS sheet and its part of base frame. It is duly painted and fitted with inlet and outlet connections and mechanical fuel gauge. Supply of Diesel to run and test the generator at full load for 8 hours.BATTERY :2 Nos 12 V 180 AH battery.h) Supply of maintenance manual books with engine and alternatore parts list.i) Supply of tools required for the maintenance and operations of the Generator set.J) Mounting of starting batteries of ½\\" thick hylem sheet base with suitable angle iron frame work support on the floor by the side of generator set to conform to latest CEIG conditions.k) supply and laying of annunciation cable of suitable capacity and length between engine and the control panel of the generator set.
463	Erection of Gen set: Providing suitable concrete foundation with cement concrete 1:2:4 with sand cushion all around the foundation erection of 125KVA Generator set over the existing foundation and erection of Generator set with proper alignment over the existing foundation to suit 125KVA Gen set foundation size Suitable.
464	Supply and fixing of 250 A Three phase 500V 4 Pole Change over Switch on suitable angle iron frame work with MS cable entry boxes with Earth connection only.
465	Preparation of site plan, physical layout, electrical line schematic diagram in 10 sets. Getting drawing approval from CEIG, preparation of completion report, rectification report and arranging CEIG’s inspection and obtaining safety certificate.
466	Supply and Laying of 3 1/2 x 185 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.
467	Supply and clamping of 3.5 x 185 sq.mm PVC LTUG ar. cable on post or on wall with MS Clamps.
468	Supply and fixing of brass cable gland for 3.5 x 185 sqmm PVC armoured LTUG cable with earth connection
469	Supply and providing cable end termination of 3.5 x 185 sqmm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc. with electrical connection complete
470	Design, Supply Installation, testing and commissioning of 8.5 TRnominal capacity ceiling suspended Ductable Air conditioner with theFollowing components.a)8.5 TR capacity ceiling suspended Ductable Air Conditioner high tech,low height, low noise level indoor unitwith fin and tube type cooling coil,Detachable type drier provided inrefrigerant circuit to reduce moisturecontent multi stage type distributorfor feeding equal quantities of theRefrigerant mixture to all the section ofthe coil, with required valves, directlycoupled blower to reduce troubles andwear & tear compared to belt driveBlower. Thermostatic expansion valve arrangement, lift and pull type aluminium framed durable, washable air filter, Integrated electrical panel with complete microprocessor control with display for easy operation and maintenance of unit common operating conditions of 45 F suction temperature Auto reset type HP/LP safety cut sensor type to improve Reliability of compressor. Type QTY- Ceiling Suspended Blower QTY – 1 NosMotor Power – 415V /3Ph/50HZAir flow -3400 CFM
471	B)8.5 TR capacity suitable for ceiling suspended Ductable Air conditioner high tech Outdoor unit with power saving high efficiency sturdy and rugged 1 No of scroll compressor each with inbuilt internal thermal protector, internal pressure relief valve, Auto reset type HP/LP safety cut sensor out to improve reliability of compressor andcondenser shall be made of super slithigh efficient aluminium fins mechanically bonded to copper tubescondenser ‘L’ type coil to be rigidlyfixed to unit frame with fastenersimported condenser fan & fan bladesto be statically and dynamicallybalanced to reduce noise andVibration. The fans are direct driven3phase motor with protection.Condensing temperature 130’f for thesystem operations. Refrigerant Compressor – ScrollNo of Compressor – 1NoRefrigerant – R22/R410Power supply – 415V/3Ph/50HZNo of Fan – 1NosTypes of Mounting – Rubber mounts with sleeve
472	Supply and filling of R-22 Refrigerant Gas.
473	Supply & fixing of hard drawn copper Refrigerant piping of suction line of Size 7/8” inches with necessary fitting and clamp etc.
474	Supply & fixing of hard drawn copper Refrigerant piping of liquid line of size 5/8” inches with necessary fitting and clamp etc...
475	Supply and fixing of flexible canvas connection between indoor unit and ducting and rubber pads, with ceiling Support angle rods etc.
476	Supply, fabrication and fixing of suitable MS angle frame outdoor AC units
477	Supply, fabrication and fixing of suitable MS angle frame indoor AC units
478	Supply, Fabrication and Installation of GI ducting Ducting arrangement with necessary angle supports, anchor fasteners and threaded rods etc. as required
479	Supply and Providing Thermal Insulation of 9mm thick –XLPE with aluminium foil./ Nitrile Rubber insulation
480	Supply and providing acoustic lining for initial portion of ducting with 10mm thick XLPE insulation.
481	Supply, fabrication and fixing of Volume control dampers individually across the duct
482	Supply and fixing of powder coated Extruded aluminium supply air grilles/diffuser with MS volume control damper for supply.
483	Supply and fixing of 1 inch PVC water drain pipe line on wall with suitable Clamp as required.
484	Towards charges for welding, leak testing, Nitrogen pressure testing, pressure holding, vaccummising, dehydration and other related works etc.
485	Supply & providing of Power supply for MCB to Outdoor unit with 4 core 10 sq.mm copper flexible cable
486	Supply & providing of control supply for Outdoor unit to Indoor unit HP and LP cut-outs with 7 core 1.5sq.mm copper flexible cable
487	Supply erection, Testing and commissioning of 2.0 TR split type 3 Star AC units fitted with hermetically sealed Air compressor with R32 refrigerant air cooled condenser, fan etc. and 1 No indoor Hi wall mounted 2.0 TR capacity evaporator unit complete with cooling coil, blower motor and connected accessories, control etc chord wire connecting indoor and outdoor unit with drain pipe suitable for operation on 230V + 10% 50Hz single phase AC supply.
488	Supply and fixing of 5 KVA voltage stabilizer (V guard /Eq.make ) suitable for 2.0 tons capacity split type air conditioner with 3 minutes time delay and low / high voltage cut off switch (wall mounting) with necessary wire connection.
489	Supply and laying of 5/8'' and 3/8'' copper pipe (Extr beyond 3Mtrs supplied with AC Unit)(For split AC Unit)
490	Supply and Fixing of MS stand for fixing outdoor units.
491	Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry
492	Supply and Run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall / floor / ground for earth connection.
493	Supply and run of 25mm x 6 mm tinned copper flat with necessary clamps/supports on wall/floor/ground for earth connection
494	Supply and laying of 2 x 10 sq.mm PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.
495	Supply and clarnping of 2 x 10 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps.
496	Supply and run of GI Hot Dip / Powder Coated 16 SWG Cable Tray with 300mm width and 50mm height with necessary clamps / supports on wall / floor / ground for earth connection.
497	supply and fixing of 65 mm dia. (2 -1/2\\") GI pipe (class B) of 6 metre length with 300mm x 300mm x 6mm MS base plate duly welded at the bottom with concreting with construction of masonary pedestal with suitable SMC box with door arrangement to house 6A SP MCB switch, 2/4 way connector on suitable hylem sheet and supply and fixing of 48W LED street light fitting with LED (Higher end) with 1 metre 32mm dia. GI pipe (class B) Complete with suitable MS clamps for LED steet light fitting and SMC box with PVC unsheathed copper leads from SMC box to fitting and with painting of suitable colour
498	Supply and Laying of 4 x16 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good
499	Supply and clamping of 4x 16 sq.mm PVC LTUG armoured LTUG cable on post or on wall with MS Clamps.
500	Supply and fixing of brass cable gland for 2 x 25/4x16 sq.mm. PVC LTUG armoured cable with earth connection

Tender Documents

SR No	FileName	File Description
1	Click here to download tender document	Tender Documents
2	Click here to download tender document	Tender Documents
3	Click here to download tender document	Tender Documents
4	Click here to download tender document	Tender Documents
5	Click here to download tender document	Tender Documents

Also Visit

Tenders

Tamil Nadu Tenders

Construction Tenders

Building Construction Tenders

Building Work Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Construction Of Integrated Commercial Taxes Office Building At Alapakkam In Chengalpattu District., Chennai-Tamil Nadu

Tender Documents

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Construction Of Integrated Commercial Taxes Office Building At Alapakkam In Chengalpattu District., Chennai-Tamil Nadu

Tender Documents

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us