|
| 1 | Page No. - 1/2 (a) Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing,spreading or stacking the spoils within a lead of 75 m. as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete.(a) Depth of excavation not exceeding 1,500 mm. |
| 2 | Page No. - 2/4 (a) (A) Filling in foundation or plinth by silver sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation with water, ramming complete including the cost of supply of sand. (payment to be made on measurement of finished quantity) |
| 3 | Page No. - 14/1Single Brick Flat Soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand. |
| 4 | Page No. - 42/36Hire and labour charges for shuttering with centering and necessary staging upto 4 m. using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams, columns, lintels curved or straight including fittings, fixing and striking out after completion of works. ( upto roof of ground floor) (When the height of a particular floor is more than 4 m the equivalent floor height. shall be taken as 4 m and extra for woks beyond the initial 4 m. ht. shall be allowed under 12(e) for every 4 m or part thereof. ) f) 25 mm to 30 mm shuttering without staging in foundation. |
| 5 | (c) Steel shuttering or 9 to 12 mm thick approved quality ply board shuttering in any concrete work |
| 6 | P - 26/10 ( Analysis rate ) Ordinary cement concrete ( mix 1:1.5:3) with graded stone chips ( 20 mm. nominal size ) excluding shuttering and reinforcement. if any , in ground floor as per relevant IS codes. a) Pakur Variety |
| 7 | Page No. - 43/40 (ii) ( Analysis rate, 10th Corrigenda dt 24.08.2022 ) Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction.(a) For works in foundation and upto roof of ground floor/upto 4 m(i) Tor steel/Mild SteelII. JSW /JSPL /SHYAM / SRMB / BMASL / ELECTROSTEEL / SSL |
| 8 | Page No - 24/4Ordinary Cement concrete ( mix 1:2:4) with graded stone chips ( 20 mm nominal size ) excluding shuttering and reinforcement , if any, in ground floor as per relevant IS codes. a) Pakur Variety |
| 9 | Page No. - 16/16125 mm. thick brick work with 1st class bricks in cement mortar (1:4) inGround floor |
| 10 | Page No. - 15/8 (a) Brick work with 1st class bricks in cement mortar (1:6)(a) In foundation and plinth |
| 11 | Page No. - 66/36 (A) Supplying and laying true to line and level vitrified tiles of approved brand (size not less than 600 mm X 600 mm X 10 mm thick) in floor, skirting etc. set in 20 mm sand cement mortar (1:4) and 2 mm thick cement slurry back side of tiles using cement @ 2.91Kg./sqM or using polymerised adhesive (6 mm thick layer applied directly over finished artificial stone floor/Mosaic etc without any backing course) laid after application slurry using 1.75 Kg of cement per sqM below mortar only, joints grouted with admixture of white cement and colouring pigment to match with colour of tiles / epoxy grout materials of approved make as directed and removal of wax coating of top surface of tiles with warm water and polishing the tiles using soft and dry cloth upto mirror finish complete including the cost of materials, labour and all other incidental charges complete true to the manufacturer's specification and direction of Engineer-in-Charge. (White cement, synthetic adhesive and grout material to be suppliedby the contrr]e) I(I) With application slurry @1.75 kg/ Sq.m, 20 mm sand cement mortar (1:4) & 2 mm thick cement slurry at back side of tiles, 0.2 kg/ Sq.m white cement for joint filling with pigment.(A) Deep Colour & White |
| 12 | Page No. - 189/1Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface](ii) With 1:6 cement mortar(b) 15 mm thick plaster |
| 13 | Page No. - 192/15 Neat cement punning about 1.5mm thick in wall, dado, window sill, floor etc.NOTE:Cement 0.152 cu.m per100 sq.m. |
| 14 | P - 83/17Supplying, fitting & fixing Industrial Troughed Aluminium sheet (excluding the supporting frame work) of approved make & brand in alloy 3105 conforming to IS: 1254-1991 fitted and fixed with 75 mm & 25 mm Self tapping screw , EPDM Washer 16 mm dia & 3 mm th washer etc complete with 150 mm. end lap and one corrugation minimum side lap.(Payment to be made on area of finished work) (Aluminium sheet to be supplied by contractor).(i) In Roof:-b) With 0.71 mm thick sheet |
| 15 | Item No. 2 / Page No. - 84/18 (A ) (a )Aluminium sheet ridging fitted with self tapping screws, EPDM washers etc complete.(Minimum 225mm end lapping).(A) 300 mm lapping each way(a) With 0.71 mm sheet |
| 16 | Item No. 18 / Page No. - 101/ 2A (3rd Corrigenda,dt - 04.06.2018)M.S. structural works with hollow sections (square or rectangular shape) conforming to IS: 806-1968 & IS:1161-1998) connected to one another with bracket, gusset, cleat as per design, drawing & direction of Engineer-in-Charge complete including cutting to requisite shape & size, fabrication including metal arc welding conforming to IS: 816-1969 & IS: 9595 using electrodes of approvedmake and brand conforming to IS:814- 2004, haulage, hoisting and erection all complete.The rate includes the cost of all M.S. Hollow section, all consumables such as electrodes, gas and hire charges of all tools and plants and labour reqired for execution and all incidental chages (such as electricity, labour insurance) etc. complete.ii) For other Structural works like galleries etc.1st Floor |
| 17 | Item No.36 / Page No. - 195/7 Applying Interior grade Acrylic Primer of approved quality and brand on plastered or cencrete surface old or new surface to receive Distemper/ Acrylic emulsion paint including scraping and preparingthe surface throughly, complete as per manufacturer's specification and as per direction of the EIC. (b) Two Coatii) Solvent based interior grade Acrylic Primer |
| 18 | Item No.37 / Page No. - 201/4 Applying Acrylic Emulsion Paint of approved make and brand on walls and ceiling including sand papering in intermediate coats including putty (to be done under specific instruction of Superintending Engineer) : (Two coats) ii) Standard Quality |
| 19 | Page No. - 196/8 Applying Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterioremulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC(a) One Coat |
| 20 | Page No. - 197/17 (c) Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturer's specification and as per direction of Engineer-in-Charge to be applied over acrylic primer as required. Therate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer.In Ground floor (Two Coat)a) Normal 100% Acrylic Emulsion |
| 21 | Page No. - 200/1 (a) (a) Priming one coat on steel or other metal surface with synthetic oilbound primer of approved quality including smoothening surfaces by sandpapering etc. |
| 22 | Page No. - 200/2 (A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary (b) On steel or other metal surface :With super gloss (hi-gloss) -(iv) Two coats (with any shade except white) |
| 23 | Page No. - 200/1 (b) (b) Priming one coat on timber surface with synthetic oilbound primer of approved quality including smoothening surfaces by sandpapering etc. |
| 24 | Page No. - 200/2 (A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary :(a) On timber surface :With super gloss (hi-gloss) -(iv) Two coats (with any shade except white) |
| 25 | Page No. - 104/13 a (ii ) (a) M.S.or W.I. Ornamental grill of approved design joints continuously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugs in ground floor.(Add extra @ 1% for each addl. floor upto 4th floor and @ 1.25%for each addl. floor above 4th floor)(ii) Grill weighing above 16 Kg./sq.mtr and aboveGround Floor |
| 26 | Page No. - 114/1 (d) Wood work in door and window frame fitted and fixed in position completeincluding a protective coat of painting at the contact surface of the frameexluding cost of concrete, Iron Butt Hinges and M.S clamps. (e) Sal : Malayasian |
| 27 | Page No. - 117/1(ii) (b) Panel shutters of door and window, as per design (each panel consisting of single plank without joint), including fitting and fixing the same in position but excluding the cost of hinge and other fittings.In ground floor.(In case of non-supply of single plank, penal rate of reduction of 20% will be made)(ii) 40mm thick shutters with 19mm thick panel of size 30 to 45 cm(b) Sishu, Gamar, Champ,Badam,Bhola, Mogra, Hallak. |
| 28 | Page No. - 140/4Supplying, fitting and fixing M.S. clamps for door and window frame made of flat bent bar, end bifurcated with necessary screws etc. by cement concrete(1:2:4) as per direction. (Cost of concrete will be paid separately)(b) 40mm X 6mm, 200mm Length |
| 29 | Page No. - 140/5Iron butt hinges of approved quality fitted and fixed with steel screws, with ISImark.(iii) 75mm. X 40mm. X 1.12mm. |
| 30 | Page No. - 146/31 Anodised aluminium decorative handle (hexagonal / fluted) of approed quality fitted and fixed complete.(i) 150mm plate x 10mm dia rod x 12mm hexagonal/fluted. |
| 31 | Page No. - 139/3 a (i) Supplying, fitting and fixing hinge cleat in position excluding the cost hinge andother fiffitngs.a) with 50mm iron Butt-hingeiii) Local Sal. |
| 32 | Page No. - 141/10 i) Iron hasp bolt of approved quality fitted and fixed complete (oxidised) with16mm dia rod with centre bolt and round fitting.(b) 250mm long. |
| 33 | Page No. - 144/26Anodised aluminium barrel / tower / socket bolt (full covered) of approvedmanufactured from extruded section conforming to I.S. 204/74 fitted and fixedwith cadmium plated screws:(vi) 200mm long x 10mm dia. Bolt |
| 34 | Page No. - 1/3Earth work in filling in foundation trenches or plinth with good earth. in layers not exceeding 150 mm. including watering and raming etc. layer by layer complete. ( Payment to be made on basis of measurement of fiinished quantity of work ) a) With earth obtained from excavation of foundation. |
| 35 | Page No. - 233/1Supplying profiles of required section made of Aluminium Alloy Extrusions conforming to IS: 732-1983 and IS: 1285- 1975; Annodized (with required film thickness and specified colour / natural) matt finishedconforming to IS: 1868-1983 for fabrication of composit door, sliding & casement windows, partitions, formed of basic sections of any ISI embossed / certified make and brand as per direction of Engineer - InCharge. (Payment will be made on finished length of the work).(A) In 10-12 Micron thickness Annodizing filmI) Natural whitea) 2- track sliding windowi) Bottom frame |
| 36 | ii) Top and side frame. |
| 37 | d) Shutter for all track sliding window.i) Bottom & Top member. |
| 38 | ii) Style side member |
| 39 | iii) Interlock member. |
| 40 | Page No. - 239/2 Labour charge for fabrication and installation of composite door, window, partitions made from annodized extruded alloy aluminium sections for the following units:-(A) Glazed aluminium sliding windows made of extruded and annodized alloy aluminium sectios, fabrications, including cutting to proper shape and size, drilling and aligning of window shutter frame fitted with in built locking arrangements, sliding rollers and other necessary fittings, fixture, adhesives and joineries along with extruded neoprine or EPDM gasketing in between window frame and masonry work (walls, column, beam.lintels etc.) as well as between glass and shutter frame for fixing glass and Polysulphide sealant and in between shutter and window frame where necessary including cutting to requisite size and fixing glass as per drawing, specification and direction of EIC. The rate includes the hire charge of all tools and plants, including all incidental charges, adhesive, joineries such as screw, cleat angle etc. but excluding the cost of extruded aluminium sections, glass, neoprene / EPDM gasket,locking arrangement and rollers.i ) 2 track sliding window |
| 41 | Page No. - 242/6 Supplying PVC rollers for sliding windows as per direction of Engineer in charge. |
| 42 | Page No. - 242/7 Supplying maruti lock (100mm) |
| 43 | Page No. - 242/8Supplying EPDM gusket of approved make and brand as per direction of Engineer in charge.i) For sliding windowsb) 'U' shaped EPDM gasket for frames |
| 44 | Page No. - 242/8Supplying EPDM gusket of approved make and brand as per direction of Engineer in charge.i) For sliding windowsa) ' T' shaped EPDM gasket for frames |
| 45 | Page No. - 249/24 Supplying bubble free float glass of approved make and brand conforming to IS: 2835-1987; (A) clear, toughened glass conforming to IS: 2553-1992 (part-II)(i) 6mm thick |
| 46 | GST Item (Effect from 18.07.2022)18 % GST on Estimated Cost of Sl No- 1 to 40 |
| 47 | Labour Welfare Cess Item (Effect from 01.11.2017) 1% Labour Welfare Cess on Estmated Cost of Sl No -1 to 41 Please Enable Macros to View BoQ information |
