Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Surface dressing of ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, leads and lifts up to all height. |
| 2 | Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a leads and lifts also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth sides of foundation etc. complete. |
| 3 | Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed by Engineer-incharge and disposing of all excavated earth at dumping site ( To be arranged by the Contractor) as per satisfacation of Engineer -in- Charge through all modes of transportation including head load , animal load or mechnical means along with its leveling fine dressing and with all kinds of labour, machineries, tools equipments and safety measures and incidentals necessary to complete the work by mechnical means and labour( If required). All useful material such as stone , shingles aggregate and slates Shall be properly Stacked at site to the maximum possible extent in all leads and lifts through all modes of transportation as per direction of the Engineer -in -charge . Any loss to the public and private property during the course of execution and disposal of serviceable and unserviceable materials shall be the absolute responsibility of the contractor and shall have to be duly compensated by him in all respects including all incidental charges. |
| 4 | Providing and laying mechanically mixed and vibrated cement concrete 1:4:8 (one cement isto four sand isto eight graded crushed stone aggregate 40mm (forty millimeter) nominal size) and curing complete, in or under water, including pumping or bailing out water/dewatering, removal of slush which may arise at the time of laying under water complete excluding the cost of form work in foundation and plinth in all depths/heights as per HPPWD specifications or as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts. The rate inclusive of Malkhana, Royality, Octroi, GST, toll tax or any taxes imposed by the Government. |
| 5 | Providing form work with steel plates 3.15mm (Three point one five millimeters) thick, welded with angle iron in frame 30x30x5mm (Thirty into Thirty into Five millimeters) so as to give a fair finish including centering, shuttering strutting and propping etc, with wooden battens and ballies, height of propping and centering in all heights. below supporting floor to ceiling and removal of the same for in – situ reinforced concrete and plain concrete work in foundation footings, basis of columns etcetera and mass concrete, including carriage of materials. Within all leads, lifts and other incidentals. The rate including Royality, Malkhana, Octroi, GST, Toll Tax Sales tax or any other taxes imposed by the Government. |
| 6 | Providing form work with steel plates 3.15mm (Three point one five millimeters)thick, welded with angle iron in frame 30x30x5mm (Thirty into Thirty into Five millimeters) so as to give a fair finish including centering, shuttering strutting and propping etc, with wooden battens and ballies, height of propping and centering in all heights below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in beams cantilevers, girders and lintels, sides and soffits of beams, beam haunchings, cantilevers, bressumers and lintels upto any depth/heights, up to all floor level, including carriage of materials within all leads, lifts and other incidentals. The rate including Royality, Malkhana, Octroi, GST, Toll Tax Sales tax or any other taxes imposed by the Government. |
| 7 | Providing form work with steel plates 3.15mm (Three point one five millimeters) thick, welded with angle iron in frame 30x30x5mm (Thirty into Thirty into Five millimeters) so as to give a fair finish including centering, shuttering, strutting and propping etc, with wooden battens and ballies, height of propping and centering in all heights below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in Columns, pillars, posts and struts, (circular or curved in plan), up to all floor level, including carriage of materials within all leads, lifts and other incidentals. The rate including Royality, Malkhana, Octroi, GST, Toll Tax Sales tax or any other taxes imposed by the Government. |
| 8 | Providing form work with steel plates 3.15mm (Three decimal one five millimeters) thick, welded with angle iron in frame 30x30x5mm (Thirty into Thirty into Five millimeters) so as to give a fair finish including centering, shuttering strutting and propping etc, with wooden battens and ballies, heights of propping and centering in all heights below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in flat surfaces such as soffits of suspended floors, roofs, landings, shelves, and the like floor, etc. up to any thickness, up to all floor level, including carriage of materials within all leads, lifts and other incidentals. The rate including Royality, Malkhana, Octroi, GST, Toll Tax Sales tax or any other taxes imposed by the Government. |
| 9 | Providing and laying in position machine batched and machine mixed design mix M-20 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge in all works upto plinth level complete as per HPPWD specifications or as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.The rate inclusive of Malkhana, Royality, Octroi, GST, toll tax or any taxes imposed by the Government. |
| 10 | Providing and laying in position machine batched and machine mixed design mix M-20 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge in all works above plinth level upto floor V level complete as per HPPWD specifications or as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.The rate inclusive of Malkhana, Royality, Octroi, GST, toll tax or any taxes imposed by the Government. |
| 11 | Providing and laying Tor steel reinforcement of TATA, sail , Rashtriya Ispat or its substantial equivalent make for Reinforced Cement Concrete work including bending, binding and placing in position complete including cost of binding wire and other incidentals due for its completion up to all floor level complete as per HPPWD specifications or as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate inclusive of Malkhana, Royality, Octroi, GST, toll tax or any taxes imposed by the Government. |
| 12 | Providing and laying Second class Brick work in super structure above plinth level upto all floor level: Cement mortar 1:6 (1 cement : 6 Coarse sand) as per Specifications, approved drawings, designs and entire satisfaction and directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidentals. The rate including of octroi, royalty, Malkana, toll tax, sale tax or other taxes imposed by the Government . |
| 13 | Providing and laying Second class Half brick masonry in super structure above plinth level upto all floor level. In Cement mortar 1 : 4 (1 cement : 4 coarse sand) as per Specifications, approved drawings, designs and entire satisfaction and directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidentals. The rate including of octroi, royalty, Malkana, toll tax, sale tax or other taxes imposed by the Government . |
| 14 | 15 (Fifteen) millimeters thick cement plaster in single coat on the rough side of brick/concrete/ stone walls for interior plastering up to all heights including arises. Internal rounded angles, chamfers and/or rounded angles not exceeding 80 (Eighty) millimeters in girth and finished even and smooth in cement mortar 1:3(One cement: Three sand)as per H.P. PWD. Specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One), including carriage of all labour, equipments and materials to various location through all modes of transportation in all leads lifts and all iincidential charges. The rate including of octroi, royalty, Malkana, toll tax, sale tax or other taxes imposed by the Government. |
| 15 | 15 (Fifteen) millimeters thick cement plaster in two coats under layer 12 mm thick cement plaster up to all heights including arises. Internal rounded angles, chamfers and/or rounded angles not exceeding 80 (Eighty) millimeters in girth and finished even and smooth in cement mortar 1:6(One cement: Six sand)as per H.P. PWD. Specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One), including carriage of all labour, equipments and materials to various location through all modes of transportation in all leads lifts and all iincidential charges. The rate including of octroi, royalty, Malkana, toll tax, sale tax or other taxes imposed by the Government. |
| 16 | 6mm (six millimeter) thick cement plaster to ceiling with cement mortar 1:3 (one cement isto three sand), upto all floor level complete as per HPPWD specifications or as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate inclusive of Royality, Malkhana, Octroi, GST, Toll Tax Sales tax or any other taxes imposed by the Government. |
| 17 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS: 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.l. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every Junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with 12.5 mm thick tapered edge gypsum moisture resistant board includng carriage of materials, labour, tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-Charge. The rate including of octroi, royalty, Malkana, toll tax, sale tax or other taxes imposed by the Government. |
| 18 | Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-incharge as per HP.PWD., Specifications includng carriage of materials, labour, tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-Charge. The rate including of octroi, royalty, Malkana, toll tax, sale tax or other taxes imposed by the Government. |
| 19 | Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors windows ventilators and partitions with extruded built up standard tublar sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-incharge. The rate including of octroi, royalty, Malkana, toll tax, sale tax or other taxes imposed by the Government. |
| 20 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. With float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm) complete as per the architectural drawings and the directions of engineer-in-charge as per HP.PWD., Specifications includng carriage of materials, labour, tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-Charge. The rate including of octroi, royalty, Malkana, toll tax, sale tax or other taxes imposed by the Government. |
| 21 | Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer's specification & drawing.30 mm thick pre laminated PVC door shutters including carriage of materials within all leads, lifts and other incidental. The rate inclusive of Malkhana, Royality, Octroi, GST, toll tax or any taxes imposed by the Government. |
| 22 | Providing and fixing factory made door frame (single rebate) made out of single piece extruded solid PVC foam profile with homogenous fine cellular structure having smooth outer integral skin having 62 mm width & 32 mm thickness, frame will be mitred & Jointed with self driven self tapping screws of size 38 mm x 4 mm & PVC solvent cement, including fixing the frame to wall with suitable dia & length anchor fastener manufacturer's specification and direction of Engineer-in-charge. |
| 23 | Providing and fixing 35 mm thick (thirty five milimetre) factory made flush door shutter non-decrative phenol bonded termite resistant and water proof core board with frame of first class hard wood and well match commercial three ply veneer with vertical grain or cross band and face veneeer both face of door IS No.2202 (two thousand two hundred two) of kit ply/Alpro comtax as per Arch drawing as per HPPWD specification 1990 volume-1 includng carriage of materials, labour, tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-Charge.The rate including of octory, royalty, malkana,toll tax, sal tax or other taxes imposed by goverment. |
| 24 | Providing wood work in frames of doors, windows, clerestory, windows and other frames wrought, framed and fixed in position in Second class Teak wood including carriage of material in all leads and lifts as per HP.PWD specification 1990 Volume-1 including carriage of materials, labour tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-Charge.The rate including of octory, royalty, malkana,toll tax, sal tax or other taxes imposed by goverment. |
| 25 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete as per HP.PWD., Specifications includng carriage of materials, labour, tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-Charge. The rate including of octroi, royalty, Malkana, toll tax, sale tax or other taxes imposed by the Government. : (a) 300x 16 mm |
| 26 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete as per HP.PWD., Specifications includng carriage of materials, labour, tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-Charge. The rate including of octroi, royalty, Malkana, toll tax, sale tax or other taxes imposed by the Government. a) 200x10mm |
| 27 | Providing and fixing anodized aluminum tower bolts, (Barrel type)anodized transparent or dyed to required colour and shade with bolts and nuts/screws etcetra . complete as per HP.PWD. Specifications, approved drawings, designs and entire satisfaction and directions of the Engineer-in-charge including carriage of materials within all leads and lifts and other incidentals. The rate including of octroi, royalty, Malkana, toll tax, sale tax or other taxes imposed by the Governmentl. 150 x 10mm (one hundred fifty into ten millimeter). |
| 28 | Providing and fixing aluminum handles anodized transparent or dyed to required colour and shade with necessary screws etcetra complete as per HP.PWD. Specifications, approved drawings, designs and entire satisfaction and directions of the Engineer-incharge including carriage of materials within all leads and lifts and other incidentals. The rate including of octroi, royalty, Malkana, toll tax, sale tax or other taxes imposed by the Government 100mm ( one hundred millimeters ) |
| 29 | Providing and fixing aluminum handles anodized transparent or dyed to required colour and shade with necessary screws etcetra complete as per HP.PWD. Specifications, approved drawings, designs and entire satisfaction and directions of the Engineer-incharge including carriage of materials within all leads and lifts and other incidentals. The rate including of octroi, royalty, Malkana, toll tax, sale tax or other taxes imposed by the Government 75mm ( seventy five millimeters ) |
| 30 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete as per HP.PWD., Specifications includng carriage of materials, labour, tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-Charge. The rate including of octroi, royalty, Malkana, toll tax, sale tax or other taxes imposed by the Government. Single rubber stopper |
| 31 | Providing and fixing 150mm (one hundred fifty milimetre) oxidized M.S. hooks and eyes as per HP.PWD. Specifications, approved drawings, designs and entire satisfaction and directions of the Engineer-incharge including carriage of materials within all leads and lifts and other incidentals. The rate including of octroi, royalty, Malkana, toll tax, sale tax or other taxes imposed by the Government |
| 32 | Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface water thinnable cement primer including carriage of materials within all leads and lifts and other incidentals. The rate including of octroi, royalty, Malkana, toll tax, sale tax or other taxes imposed by the Government . |
| 33 | Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.two coat as per HPPWD specifications or as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate inclusive of Royality, Malkhana, Octroi, GST, Toll Tax Sales tax or any other taxes imposed by the Government. |
| 34 | Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equarlied on undecorated wall surface (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc.with in all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. |
| 35 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete as per H.P. PWD. Specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One), including carriage of all labour, equipments and materials to various location through all modes of transportation in all leads lifts and all iincidential charges. The rate including of octroi, royalty, Malkana, toll tax, sale tax or other taxes imposed by the Government. a) 600x600mm. The size shown in inicative and Engineer-in-charge decision /approval will be final. |
| 36 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS: 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement 4 Coarse sand), Jointing with grey cement slurry @3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete including carriage of materials within all leads, lifts and other incidental. The rate inclusive of Royality, Malkhana, Octroi, GST, Toll Tax Sales tax or any other taxes imposed by the Government. |
| 37 | Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete including carriage of materials within all leads, lifts and other incidental. The rate inclusive of Royality, Malkhana, Octroi, GST, Toll Tax Sales tax or any other taxes imposed by the Government. |
| 38 | Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement: 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. flamed finished granite stone slab jet black cerry red, elite brown cat eye or equivalent. all complete as specified and as directed by the Engineer-in-Charge: including carriage of materials within all leads, lifts and other incidental. The rate inclusive of Royality, Malkhana, Octroi, GST, Toll Tax Sales tax or any other taxes imposed by the Government. |
| 39 | Providing and fixing on wall faces PVC (D-Plast) type-B rain water pipes of working pressure not less than 4.5 kg/Sq cm including filling the joints with approved adhesive complete. Weep holes 150mm dia pipes etc.complete as per HP.PWD specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One)and as directed by Engineer Incharge at site, including carriage of all labour equipment and material to various location through all modes of transportation with all leads and lifts, including all iincidential charges.The rate including of octory, royalty, malkana,toll tax, sal tax or other taxes imposed by goverment. |
| 40 | Providing and fixing on walll faces PVC (D-Plast) type-B accessories for rain water pipes including filling the joints with approved adhesive complete PVC Plain Bend 150mm dia etccomplete as per HP.PWD specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One)and as directed by Engineer Incharge at site, including carriage of all labour equipment and material to various location through all modes of transportation with all leads and lifts, including all iincidential charges.The rate including of octory, royalty, malkana,toll tax, sal tax or other taxes imposed by goverment. |
| 41 | Providing and fixing stainless steel (SS 304 grade) adjustable friction windows stays of approved quality with necessary stainless steel screws etc. to the side hung windows as per the architectural drawings and the directions of engineer-in-charge as per HP.PWD., Specifications includng carriage of materials, labour, tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-Charge. The rate including of octroi, royalty, Malkana, toll tax, sale tax or other taxes imposed by the Government.a) 510x19mm |
| 42 | Providing and fixing 0.60mm thick prepainted steel sheet of TATA Durashine or its substantilay equivalent make in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6 mm dia metre with prepainted limpet and rubber washers complete with all accessories as required as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.The rate including of octory, royalty, malkana,toll tax, sal tax or other taxes imposed by goverment.The rate including of octory, royalty, malkana,toll tax, sal tax or other taxes imposed by goverment. |
| 43 | Providing and fixing ridges or hips 60 cm over all with 0.45mm thick prepainted steel sheets of TATA DURASHINE TATA Durashine or its substantilay equivalent make in roofing with hot dipped metallic zinc coated sheets with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating+ back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts & nuts 6 mm dia & prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer-in-Charge.The rate including of octory, royalty, malkana,toll tax, sal tax or other taxes imposed by goverment. |
| 44 | Providing and fixing 15cm. Wide 45 cm. Overall semicircular plain G.I. Sheet gutter with iron brackets 40x3mm size bolts and nuts and washers etc. Including making necessary conections with rain water pipe complete as per design. 0.63 mm thick sheet. as per H.P. PWD. Specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One), including carriage of all labour, equipments and materials to various location through all modes of transportation in all leads lifts and all iincidential charges |
| 45 | Providing and fixing M.S BP Sheet 2mm thick in eaves board/facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer .,complete as per HP.PWD specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One)and as directed by Engineer Incharge at site, including carriage of all labour equipment and material to various location through all modes of transportation with all leads and lifts, including all iincidential charges.The rate including of octory, royalty, malkana,toll tax, sal tax or other taxes imposed by goverment |
| 46 | Structural steel work riveted, bolted or welded in built up sections/hollow sections etc., trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete :- as per HP.PWD., Specifications includng carriage of materials, labour, tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-Charge. The rate including of octroi, royalty, Malkana, toll tax, sale tax or other taxes imposed by the Government. |
| 47 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work etc. complete as per H.P. PWD. Specification 1990 (One thousand Nine hundred Ninety) Volume-1 (One), including carriage of all labour, equipments and materials to various location through all modes of transportation in all leads lifts and all iincidential charges. The rate including of octroi, royalty, Malkana, toll tax, sale tax or other taxes imposed by the Government. |
| 48 | Painting steel work with deluxe multi surface paint to give an even shade to or more coats [email protected] ltr/10 sq mt. over and under coat of primer applied@ 0.80 ltr/10sq mt of approved brand and manufacture includng carriage of materials, labour, tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-Charge. The rate including of octroi, royalty, Malkana, toll tax, sale tax or other taxes imposed by the Government |
| 49 | Providing and fixing M.S. Grills of required patterns in wooden frames of windows etc. With M.S Flats, square or round bars with round headed bolts and nuts or by screws. Plain Grill. as per HPPWD specification 1990 volume-I includng carriage of materials, labour, tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-Charge.The rate including of octory, royalty, malkana,toll tax, sal tax or other taxes imposed by goverment. |
| 50 | Stone filling under floor dry hand packed with hard stone of approved quality consolidated properly with hand or mechanical hammer to required level as per HP.PWD specification 1990 Volume-1 including carriage of materials, labour tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-Charge. |
| 51 | Supplying and providing pre moulded joint filler, 25 mm thick for expansion joint including all cost of materials and labour etc includng carriage of materials, labour, tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-Charge.The rate including of octory, royalty, malkana,toll tax, sal tax or other taxes imposed by goverment. |
| 52 | Providing and fixing to wall ceiling and floors galvanized mild steel tubes(Jindal, hindware and its equivalent) 15 mm nominal bore (medium grade) tube fitting and clamps including making good the wall ceiling and floors ISI marked per HP.PWD., Specifications includng carriage of materials, labour, tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-Charge. The rate including of octroi, royalty, Malkana, toll tax, sale tax or other taxes imposed by the Government |
| 53 | Providing and fixing various capacity.store well branded ISI marked Polythene water tank with 40 (Forty) millimetre nominal size bore galvanized Mild Steel scour tube with fitting 25 (Twenty Five) millimetre nominal bore galvanized Mild Steel overflow tube with fittings and mosquito proof coupling of approved municipal design 15 (Fifteen) millimetre nominal size ball valve and mosquito proof PVC cover with locking arrangement including providing pads of size as required for inlet and outlet tube complete ISI marked per HP.PWD., Specifications includng carriage of materials, labour, tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-Charge. The rate including of octroi, royalty, Malkana, toll tax, sale tax or other taxes imposed by the Government (a) 1000 litres net capacity tank |
| 54 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 15mm nominal bore includng carriage of materials, labour, tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-Charge. |
| 55 | Providing and fixing viterous China wash basin of Hindware Cat No. 10001 or equivalent with single hole for pillar tap with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fitting per HP.PWD., Specifications includng carriage of materials, labour, tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-Charge. The rate including of octroi, royalty, Malkana, toll tax, sale tax or other taxes imposed by the Government (i) Flat back :-(a) 630 X 450 mm |
| 56 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required includng carriage of materials, labour, tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-Charge. |
| 57 | Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge includng carriage of materials, labour, tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-Charge. |
| 58 | Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. 18.74.1 15 mm nominal bore with 30cm length 15 mm nominal bore with 45 cm length |
| 59 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore includng carriage of materials, labour, tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-Charge. |
| 60 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end): 25 mm nominal bore includng carriage of materials, labour, tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-Charge. |
| 61 | Providing and fixing high pressure P V C ( poly vinyl chloride) spigot and socket waste ventilating pipes ISI marked including fixing with approved adhesive complete 110 mm (one hundred ten millimeters) diameter as per HP.PWD specification, including carriage of all labour equipment and material to various locations through all modes of transportation in all leads lifts and all incidental charges.The rate including of octroi, royalty, Malkana, toll tax, sale tax or other taxes imposed by the Government |
| 62 | Providing and fixing high pressure P V C ( poly vinyl chloride) spigot and socket waste ventilating pipes ISI marked including fixing with approved adhesive complete 75mm ( seventy five millimeters) diameter as per HP.PWD specification, including carriage of all labour equipment and material to various locations through all modes of transportation in all leads lifts and all incidental charges.The rate including of octroi, royalty, Malkana, toll tax, sale tax or other taxes imposed by the Government |
| 63 | Providing and fixing high pressure P V C ( poly vinyl chloride) spigot and socket waste ventilating pipes ISI marked including fixing with approved adhesive complete 300mm ( Three hundred millimeters) diameter as per HP.PWD specification, including carriage of all labour equipment and material to various locations through all modes of transportation in all leads lifts and all incidental charges.The rate including of octroi, royalty, Malkana, toll tax, sale tax or other taxes imposed by the Government |
| 64 | Providing and fixing PVC (finolex) plain bend 110 mm nominal bore ISI marked complete including fixing with approved adhesive etc. complete as per HP.PWD specification, including carriage of all labour equipment and material to various locations through all modes of transportation in all leads lifts and all incidental charges.The rate including of octroi, royalty, Malkana, toll tax, sale tax or other taxes imposed by the Government |
| 65 | Providing and fixing PVC (finolex) plain bend 75 mm nominal bore ISI marked complete including fixing with approved adhesive etc. complete as per HP.PWD specification, including carriage of all labour equipment and material to various locations through all modes of transportation in all leads lifts and all incidental charges.The rate including of octroi, royalty, Malkana, toll tax, sale tax or other taxes imposed by the Government |
| 66 | Providing and fixing PVC (finolex) single equal branch 110 mm nominal bore with oval access door, ISI marked insertion rubber washer 3 mm thick bolts and nuts complete including fixing with approved adhesive etc. complete as per HP.PWD specification, including carriage of all labour equipment and material to various locations through all modes of transportation in all leads lifts and all incidental charges.The rate including of octroi, royalty, Malkana, toll tax, sale tax or other taxes imposed by the Government |
| 67 | Providing and fixing PVC (finolex) single equal branch 75 mm nominal bore with oval access door, ISI marked insertion rubber washer 3 mm thick bolts and nuts complete including fixing with approved adhesive etc. completeas per HP.PWD specification, including carriage of all labour equipment and material to various locations through all modes of transportation in all leads lifts and all incidental charges.The rate including of octroi, royalty, Malkana, toll tax, sale tax or other taxes imposed by the Government |
| 68 | Providing and fixing PVC (finolex) single equal branch 110 mm nominal bore plain ISI marked including fixing with approved adhesive etc. complete as per HP.PWD specification, including carriage of all labour equipment and material to various locations through all modes of transportation in all leads lifts and all incidental charges.The rate including of octroi, royalty, Malkana, toll tax, sale tax or other taxes imposed by the Government |
| 69 | Providing and fixing PVC (finolex) single equal branch 75 mm nominal bore plain ISI marked including fixing with approved adhesive etc. complete as per HP.PWD specification, including carriage of all labour equipment and material to various locations through all modes of transportation in all leads lifts and all incidental charges.The rate including of octroi, royalty, Malkana, toll tax, sale tax or other taxes imposed by the Government |
| 70 | Providing and fixing PVC (finolex) single equal branch 110 mm nominal bore door tee ISI marked including fixing with approved adhesive etc. complete as per HP.PWD specification, including carriage of all labour equipment and material to various locations through all modes of transportation in all leads lifts and all incidental charges.The rate including of octroi, royalty, Malkana, toll tax, sale tax or other taxes imposed by the Government |
| 71 | Providing and fixing PVC (finolex) single equal branch 75 mm nominal bore door tee ISI marked including fixing with approved adhesive etc. complete as per HP.PWD specification, including carriage of all labour equipment and material to various locations through all modes of transportation in all leads lifts and all incidental charges.The rate including of octroi, royalty, Malkana, toll tax, sale tax or other taxes imposed by the Government |
| 72 | Providing and fixing PVC(Finolex) collars 110 mm nominal bore ISI marked including fixing with approved adhesive etc. complete as per HP.PWD specification, including carriage of all labour equipment and material to various locations through all modes of transportation in all leads lifts and all incidental charges.The rate including of octroi, royalty, Malkana, toll tax, sale tax or other taxes imposed by the Government |
| 73 | Providing and fixing PVC(Finolex) collars 75 mm nominal bore ISI marked including fixing with approved adhesive etc. complete as per HP.PWD specification, including carriage of all labour equipment and material to various locations through all modes of transportation in all leads lifts and all incidental charges.The rate including of octroi, royalty, Malkana, toll tax, sale tax or other taxes imposed by the Government |
| 74 | Providing and fixing PVC(finolex) floor trap (110mmx 75 mm) ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete as per HP.PWD specification, including carriage of all labour equipment and material to various locations through all modes of transportation in all leads lifts and all incidental charges.The rate including of octroi, royalty, Malkana, toll tax, sale tax or other taxes imposed by the Government |
| 75 | Constructing masonry Chamber 90x90x100 cm inside, in brick work in cement mortar 1:4 (1 cement: 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement: 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement: 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design with common burnt clay F.P.S. (non modular bricks of class designation 7.5 including carriage of all labour equipment and material to various locations through all modes of transportation in all leads lifts and all incidental charges.The rate including of octroi, royalty, Malkana, toll tax, sale tax or other taxes imposed by the Government |
| 76 | Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors: 100 mm inlet and 100 mm outlet Sand cast iron S&S as per IS: 3989 |
| 77 | Providing and fixing 600mmx450mm bevelled edge mirror of superior glass mounted on 6mm thick A.C. sheet or ply wood sheet and fixed to wooden plugs with C.P. brass screws and washeras per HP.PWD., Specifications includng carriage of materials, labour, tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-Charge. The rate including of octroi, royalty, Malkana, toll tax, sale tax or other taxes imposed by the Government |
| 78 | Providing and fixing chromium plated brass soap dish with C.P. brass brackets fixed to wooden cleats with C.P. brass screws including carriage of materials, labour, tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-Charge |
| 79 | Providing and fixing C.P. Brass shower rose with 15 or 20mm inlet 100mm dia meter including carriage of materials, labour, tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-Charge |
| 80 | Providing and fixing C.P. brass towel rail (heavy duty ISI marked IS : 8931 and 8934) complete with C.P. brass brackets fixed to wooden plugs with C.P. brass screws as per HP.PWD., Specifications includng carriage of materials, labour, tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-Charge. The rate including of octroi, royalty, Malkana, toll tax, sale tax or other taxes imposed by the Government :-600 X 20 mm |
| 81 | Providing and fixing 15mm (fifteen milimetre) C.P. stop cocks as per HP.PWD specification, including carriage of all labour equipment and material to various location through all modes of transportation in all leads lifts and all incidental charges. Please Enable Macros to View BoQ information |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
