Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Excavation in foundation, trenches etc. in earth work in all classification of soil such as pick work, jumper work, pick jumper work, blasting work, jumper blasting work, soft and hard blasting and saturated soil, de-watering, including wedging out rocks where blasting work is prohibited, chiseling or any other mixed variety of soil, including shoring, shuttering and pumping out water upto any depth or any quontam of water including slush which may be arise during de-watering removal of slush and stacking the serviceable and un-serviceable material clear from the edge of excavation as direction of Engineer-In-Charge and retuning the stacked soil in 15cm (Fifteen centimeter) layers, when required into plinths, sides of foundation etc; consolidating each deposited layer by ramming, watering and then disposing of all excavated earth as directed by the Engineer-in-Charge, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rates inclusive of octori, royality, Malkhana, toll taxes, GST and any other taxes imposed by the Government. |
| 2 | Supplying and Filling in plinth with sand filling under floors including watering ramming, consolidating and dressing complete as per HPPWD specifications and as directed by Engineer-in-Charge, including carriage of material within all leads, lifts and other incidental Charges. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sale Tax, GST or any other taxes imposed by the Government. |
| 3 | Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in Foundation footings, bases of columns and mass concrete within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 4 | Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in flat surfaces such as soffits of suspended floors roofs, landings as per Architectural drawing and the like within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 5 | Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in beams cantilevers girders and lintels sides and soffits of beams, beam haunchings, cantilevers, bressumers and lintels upto all depths within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 6 | Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in columns pillar posts and struts Square, rectangular or polygonal in plan within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 7 | Providing form work with steel plates of 3.15mm (Three decimal fifteen millimetres) thick, welded with angle iron in frames of 30x30x5mm(Thirty into Thirty into Five millimetres),so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights and removal of the same for in-situ reinforced concrete and plain concrete work in stairs cases with slopping or stepped soffits, excluding, landing, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 8 | Providing form work with steel plates of 3.15mm (Three decimal fifteen millimetres) thick, welded with angle iron in frames of 30x30x5mm(Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights and removal of the same for in-situ reinforced concrete and plain concrete work in edges of slabs and breaks in floors and walls under any thickness within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 9 | Providing and fixing 150 MM dia M.S hollow pipe post for porch complete as per HPPWD specifications and as directed by Engineer-in-Charge, including carriage of material within all leads, lifts and other incidental Charges. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sale Tax, GST or any other taxes imposed by the Government. |
| 10 | Providing and laying cement concrete 1:4:8 (One cement isto Four sand isto Eight graded broken/crushed stone aggregate 40mm (Forty milimetres ) nominal size and down gauge) mechanically mixed and curing complete excluding cost of forms work in foundation and plinth within all leads, lifts of materials and other incidentals as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sale Tax, GST or any other taxes imposed by the Government. |
| 11 | Filling in plinth with stone filling under floors including watering ramming, consolidating and dressing complete as per HPPWD specifications and as directed by Engineer-in-Charge, including carriage of material within all leads, lifts and other incidental Charges. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sale Tax, GST or any other taxes imposed by the Government. |
| 12 | Coursed rubble masonry coursed with hard stone of approved quality in foundation and plinth including racking out joints with cement mortar 1:6 (One cement isto Six sand) and curing complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 13 | Providing and laying in position machine batched and machine mixed cement concrete work of grade M-20 ( M- twenty) design mix to obtain the compressive strength of 20N/mm 2 (twenty newton per Square milimetre) for reinforced cement concrete work, using cement with cement content not less than @ 360 kg/cum. ( three hundred sixty kilogram per cubic metre) or as per approved design mix for all work upto plinth level to give a smooth surfaces mechnically mixed and vibrated including curing complete and pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals.. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 14 | Providing and laying in position machine batched and machine mixed cement concrete work of grade M-25 ( M- twenty five ) design mix to obtain the compressive strength of 20N/mm 2 (twenty newton per Square milimetre ) for reinforced cement concrete work, using cement contents not less than @ 360 kg/cum. ( three hundred sixty kilogram per cubic metre) and as per approved design mix for all work above plinth level to give a smooth surfaces mechanically mixed and vibrated including curing complete and pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate inclusive of Malkhana, Royality, Octroi, toll tax or any taxes imposed by the Government. |
| 15 | Providing Tor steel reinforcement of Sail / Tisco /Tata for reinforced cement concrete work including bending, binding, straighting, cutting and placing in position complete including cost of binding wires complete for all floors within all leads, lifts of materials and other incidentals as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 16 | Providing and laying Damp Proof Course 100mm (One Hundred milimetres) thick with cement concrete 1:2:4 (one cement: two sand: four graded crushed stone aggregate 12.5mm (Twelve decimal five milimetres nominal size) and curing complete, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 17 | Applying a coat of hot bitumen mexphalt 80/100 (Eighty/Hundred) 1.70 Kgs. (one decimal seventy Kilogram’s) per square metre. On Damp Proof Course after cleaning the surface with a piece of cloth lightly soaked in kerosene oil; within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 18 | Second class half brick work using common burnt clay building bricks in super-structure upto all floor level in cement mortar 1:4 (one cement :four sand) within all leads, lifts of materials and other incidentals, as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 19 | Second class brick work using common burnt clay building bricks in super-structure upto all floor level in cement mortar 1:6 (One cement isto Six sand) and curing complete,within all leads, lifts of materials and other incidentals, as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 20 | Providing and fixing Coloured anodised aluminium frames for door, window and ventilator and glazing partition extrusion section of Jindal/ Hindalco as per approved shade with extruted built up standard tubular and other sections of approved make confirming to IS:733 and IS:1285 anodised transparent or dyed to require shade according to IS:1868 (minimum anodic coating of grade AC15) fixed with raw plugs and screws or with fixing clips , necessary filling up of gaps and junctions at top , bottom and sides with required PVC / neoprene filles etcetra aluminium section shall be smooth rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium, snap beeding for glazing/ panelling C.P. brass / stainless steel screws all complete as per approved specifications, drawing and design including carriage of material with in all leads, lifts and other incidentals. The rate is including of octroi, royality, Malkana, sale tax, toll tax , sales tax or other taxes imposed by the government. |
| 21 | Providing and fixing coloured aluminium shutter work Jindal/ Hindalco for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15 (fifteen) within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government. ge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government |
| 22 | Providing and fixing Fly proof shutters for doors, windows and clerestory windows stainless steel grade 304 with M.S. flat 15X3mm (fifteen into three milimetre) wire gauge with 0.5 mm dia (zero decimal five milimetre) diametre wire and 1.4mm (one decimal four milimetre) wide aperture on both sides complete including carriage of material within all leads, lifts of materials and other incidentals. as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government. |
| 23 | Providing and fixing to existing door frames, 30mm thick factory made PVC panelled door shutter consisting of frame made out of M.S. tubes of 19 gauge( Ninteen gauge) thickness and size of 19mm x19mm ( Ninteen into ninteen millimeters) for styles and 15mmx15mm ( fifteen into fifteen millimeters)for top & bottom rails, M.S. frame shall have a coat of steel primers of approved make and manufacture M.S. frame covered with 5mm( five millimeters) thick heat moulded PVC \\"C\\" channel of size 30mm( thirty millimeters)thickness, 70mm( Seventy millimeters) width cut of which 50mm ( fifty millimeters)shall be flat and 20mm ( twenty millimeters) shall be tappred in 45 ( forty five)degree angle on either side forming style and 5 mm( five millimeters) thick, 95mm ( ninety five millimeters) wide, PVC sheet out of which 75mm shall be flat and 20mm( twenty millimeters) shall be tapered in 45 ( forty five)degree on the inner side to form top and bottom rail and 115mm( one hundered fifteen millimeters) wide PVC sheet out of which 75mm (seventy five millimeters) shall be flat and 20mm ( twenty millimeters) shall be tapered on both side to form lock rail, top, bottom and lock rail shall be provided either side of the panel 10mm( ten millimeters) thick, 20mm( twenty millimeters) wide cross PVC sheet be provided as gap insert for top rail and bottom rail paneling of 5mm thick both side PVC Sheet to be fitted in the M.S. frame welded/sealed to the style & rails jointed mitred and jointed with solvant cement adhesive including fixing of PVC shutter with existing frame with MS butt hinges/riveted with necessary screws of code No. 9.120 of Rajshri including and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the government. |
| 24 | Providing and fixing factory made 30 mm thick plain PVC door shutters panel PVC door shutter of RAJSHRI ( Code no 9- 120 )consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer's specification & drawing.The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 25 | Providing and fixing 8 mm (Eight milimetre) anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm ( two hundred milimetre) centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in- charge. (Only weight of grill to be measured for payment).complete including carriage of material within all leads, lifts of materials and other incidentals. as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government. |
| 26 | Providing and fixing 12mm (Twelve millimetre) thick Phenol Bonded (Both Sides) Prelaminated BWP Grade Partical Board in Matt Finish Flat pressed three layeror graded wood partical board conforming to IS No. 12823 of action Tesa/ Greenlam/ Merinolam/Kitlam/Vista as per ISI and approved shade Grade-I type-II in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etcetra complete as per PWD specification, drawing and design. and entire satisfaction of Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. Rate inclusive toll tax, GST and any other taxes imposed by the Government. |
| 27 | Providing and fixing glazing With float glass panes of 5 mm ( Five milimetres) thickness (weight not less than 12.50kg/square metre) of modi guard/saint gobain/AIS/Atul/Gold Plus in door, windows, ventilators shutter and partitions with EPDM rubber/Neoprene gastet etcetera as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 28 | Providing and fixing Glazing with frosted glass panes 5 mm ( Five milimetres) thickness glass panes (weight not less than 10.00kg/square metre) of modi guard/saint gobain/AIS/Atul/Gold Plus in door, windows, ventilators shutter and partitions with EPDM rubber/Neoprene gastet etcetera as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 29 | Providing and fixing the complete box of cup board shell be made of 25mm (Twenty Five millimetre) thick water proof termite resistant commercial board of Uniply / Green ply/ Century ply / Kitply / Dura ply / Marino ISI marked including shelves.Back side of board shall have 6 to 8 mm (Six to eight millimetre) thick water proof ply all the cut portion of board shall have 6 mm (Six millimetre) thick hard wood edging. The shutter from all side shall be finished with 1mm thick lamination ISI Marked of approved shade of Century / Greenlam /Action Tesa and 19 mm (Nineteen millimetre) thick water proof comercial board of Uniply / Green ply/ Century ply / Kitply / Dura ply / Marino including hinges, PTMT handle in wood colour of Prayag Polymers,knob megnatic catcher complete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 30 | Providing and fixing magnetic catcher for cup board shutters with necessary screws etcetra; within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge.The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 31 | Providing and fixing 65x35mm (Sixty five into Thirty five millimetres) special quality bright finished brass cup-board locks or ward robe locks with six levers including necessary screws etcetra complete (Indian make of approved quality) within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge.The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 32 | Providing and fixing 20 mm (twenty millimetres) dia stainless steel curtain rod having wall thickness of 1.25mm with two chromium plated brass brackets fixed with C.P. brass screws and PVC sleeves etc., wherever necessary complete as per approved shade within all leads, lifts of materials and other incidentals as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government. |
| 33 | Providing and fixing 300x16mm (Three hundred into Sixteen milimetres) size Pilot/sheel or equivalent anodized aluminium sliding door bolts anodized transparent or dyed to required colour and shade with necessary screws etc. within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge.The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government. |
| 34 | Providing and fixing aluminium Pilot/sheel anodized transparent or dyed to required colour and shade with necessary screws etc.Tower bolts (Barrel type) as approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 35 | 200x10mm (Two hundred into Ten milimetres) size |
| 36 | 150x10mm (One hundred fifty into Ten milimetres) size |
| 37 | Providing and fixing aluminium Pilot/sheel or equivalent anodized transparent or dyed to required colour and shade and of approved make with necessary screws etc. handles with the necessary screws etc. complete. within all leads, lifts of materials and other. incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.125mm (One hundred twenty five milimetres) size |
| 38 | Providing and fixing 150 mm size aluminium hooks and eyes complete in all respect , within all leads, lifts of materials and other. incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 39 | Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg ( thirty five kilogram) and door width upto 700 to 1000 mm ( seven hundred to one thousand milimetres), with necessary accessories and screws etc. complete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. other taxes imposed by the Government. |
| 40 | Providing and fixing aluminium hanging floor door stopper, Twin rubber stopper ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 41 | Providing and fixing 25mm (twenty fivemillimeters) thick Kota stone mirror slab flooring 55X55cm (Fifty five into Fifty five centimetre) size with Jaishmer band 7.50cm (Seven point five zero centimetre) wide/ internal; desigening in the ratio of 70% % 80% as per detail over 20 mm (Twenty milimetre) (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) complete as per HPPWD specifications and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Malkhana, Octroi, Toll tax, GST or any other taxes imposed by the Government. |
| 42 | Providing and laying Size of (600x 600mm) (Six hundred into Six hundred milimetre) Double charged/Ultra charged vetrified tiles of Restile/Nitco /Rak/Kajaria / Orient -Bell/AGL/Simpolo /Johnson/Somany/ Orient & Bell as per approved shade and design of the office in flooring (thickness to be specified by the manufacturer) with water absorption less than 0.08% ( zero decimal zero eight percentage) and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm ( twenty milimetres) thick cement mortar 1:4 (one cement isto four coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm ( three decimal three kilogram per squaremetre) including grouting the joints with white cement and matching pigments etc., complete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 43 | Providing and laying 600x600 mm ( six hundred into six hundred millimetre) full body matt finish vetrified tiles of restile/ Nitco/ Rak/ Simpolo/ Kajaria/ Johnson as per approved shade in flooring laid over 12 mm ( twelve millimetre) thick cement mortar 1:3 (one cement isto three sand) jointed with cement slurry mixed with pigment to match the shade of tiles as per approved specification, drawing and design complete including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government. |
| 44 | Providing and laying ceremic tiles antiskid non slippery of Kajaria/Nitco/Orient Bell/somany/ AGL/Rak/Johnson in flooring (300*300) mm (Thirty into thirty millimeter) size laid on treads of steps laid on 12mm thick cement mortar 1:3 finished with flush pointing in white cement slurry mixed with pigment to match the shade of tile including rubbing/nosing/moulding and polishing complete as per specification, approved drawing , design, as per the entire satsifaction and direction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government.. |
| 45 | Providing and laying 200X300 mm (two hundred into three hundred fifty millimetre) white Glazed tile of Premimum quality of Nitco/ Kajaria/ /Johnson/ AGL/ Somany/ Orient Bell in Dado/Skirting on 12mm (twelve millimetre) thick cement mortar 1:3 (one cement isto three sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete within all leads, lifts of materials and other incidentals. as per approved architectural drawing, design and specification as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 46 | Providing and laying 25mm thick mirror polished kota stone in Single slab with round noising in skirting/ dado laid on 12mm ( twelve millimeters ) thick in cement mortar 1:3 ( one cement is to three sand and jointed with grey cement slurry with pigment to match the shade of the kota stone i/c rubbing and mirror polishing complete within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 47 | Providing and fixing 19 mm (Nineteen millimeters) thick Granite stone slab on counter top/ work top having semi round nosing gang saw cut, mirror polished, premoulded and prepolished, machine cut for work top with semi nosing of required size of approved shade, colour and texture laid over 20 mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete as per specification, drawing, design and direction by the Engineer in charge including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Malkhana, Octroi, Toll tax, GST or any other taxes imposed by the Government. |
| 48 | Providing and laying 300x300x25mm (Three hundred into three hundred into twenty five millimetre) labrador design(Rainbow series of NTC/ Atlantic slab flooring 40mm (forty millimetre) average thick on 20mm (twenty millimetre) average thick fixed on floor, Ramp cement Mortar 1:3 (One cement isto three sand) jointed with neat cement slurry mixed with pigment to match the shade of tiles including rbbing and polishing, cutting and moulding complete including carriage of materials within all leads, lifts and other incidentals. Rate inclusive toll tax, GST and any other taxes imposed by the government. |
| 49 | Providing and fixing hand rail of 50 mm (fifty milimetres) dia SST stainless steel pipe handrail fixed with 35 mm ( thirty five milimetres) diametre sst pipe as per detail in combination of 35 mm ( thirty five milimetres) SST square pipe and 15 /20 mm ( fifteen/ twenty milimetres) SST(Stainless steel) pipe three row between step and railing in equal space and jointed with electic gas welding at top along wth 50mm(fifty milimetres) diametre hand rail jointing in steps as per approved drawing, design and specification and direction by the Engineer in charge including carriage of materials within all leads, lifts and other incidental.. The rate is including Royality, Malkana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government. |
| 50 | Providing and fixing SST hand railing for ramp for Divyang withl 50mm (fifty milimetres) Dia. SST (Stainless steel) Pipe handrail slip resistant with round ends at two levels at 75 Cm (Seventy five centimetres) and 90cm (Ninety centimetres) height and extended 30cm (Thirty centimetres) beyond the top and bottom of the ramp. The hand should be fixed on 15x50mm of stainless steel baluster placed st 120mm (One hundred twenty milimetres) centre to centre including welding, grinding, buffering, polishing and making the good as per approved architectural drawing, design and specification and direction by the Engineer in charge including carriage of materials within all leads, lifts and other incidental.. The rate is including Royality, Malkana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government. |
| 51 | Providing and fixing ridges or hips 60 cm (Sixty centimetres) over all with 0.60mm (Zero decimal Sixty milimetres) thick prepainted steel sheet ISI marked - Z 120 of approved make in ridges of Sail / Relience / Jindal /Tata Durashine with hot dipped metallic Zinc coated sheet with top coat of regular modified polyester (RMP) organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating of back coat of polyester of 5 (Five) microns over 5 (Five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (Six milimetres) diametres with prepainted G.I. limpet and bitumen washers complete with all accessories as required within all leads, lifts of materials and other. incidentals. as per approved architectural drawing, design and specification as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 52 | Providing and fixing valleys 90 cm (ninety centimetres) over all over all with 0.60mm (Zero decimal Six zero milimetres) thick prepainted sheet ISI marked - Z 120 of Sail / TATA / Relience / Jindal steel roofing with hot dipped metallic Zinc coated sheet with top coat of regular modified polyester (RMP) organic coating of 20 (Twenty) microns over 5 (five) micron primer coating, back coat of polyster of 5 (Five) microns including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (Six milimetres) diametres with prepainted G.I. limpet and bitumen washers complete with all accessories as required within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 53 | Providing and fixing 0.60mm (Zero decimal Six Zero milimetres) thick prepainted steel sheet ISI marked - Z 120 of Tata Durashine/ Sail / Reliance / Jindal steel in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster (RMP) organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating to back coat of polyster of 5 (five) microns over 5 (Five) microns primer fixing with prepainted iron J or L hooks,bolts and nuts with prepainted limpet and rubber washers complete with all accessories as required within all leads, lifts of materials and other. incidentals. as per approved architectural drawing, design and specification and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 54 | Providing and fixing 30cm (Thirty centimetre) wide 25cm (Twenty five centimetre) deep plain G.I. sheet gutter of 0.60mm (zero decimal six zero millimetre) thick sheet fixed with bolts, nuts and washers etcetra having dome shape gratting including making necessary connections with rain water pipe complete including cost and carriage of material with in all leads, lifts and other incidentals as per specifications, approved drawing and design, as per the direction and entire satisfaction of Engineer-in-Charge. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government. |
| 55 | Providing and fixing plain M.S. B.P. sheet of TATA/SAIL/JINDAL steel 2.00 mm (Two decimal zero millimeter) thick fixed in eaves board / facia / soffits /ceiling including cutting, fixing and welding to steel rafter, member and applying a coat of red lead primer with gas/ electric welding in position complete (frame work is to be measured and paid for separately) within all leads, lifts of materials and other. incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 56 | Providing and fixing flashing 38cm (Thirty eight centimetre) overall with 0.60mm (zero decimal six zero millimetre) thick prepainted sheet of Tata / sail / Reliance / Jindal with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating + back coat of polyster of 5 (Five) microns over 5 (Five) microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm (Six millimetre) dia meter & prepainted G.I. limpet & bitumen washers complete. as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST and any other taxes imposed by the Government. |
| 57 | Providing and fixing on wall face 150mm (One hundred fifty milimetres) diametres P.V.C. rain water pipes of working pressure 4.6kg (four / six kilogramme) per square centimetre of finolex / Relience / vectus/ prince pipe for rain water pipe fixed with approved adhesive including filling the joints complete within all leads, lifts of materials and other incidentals, and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 58 | Providing and fixing on wall face 150 mm (One hundred tenfifty millimetre) diametre plain bend Providing and fixing on wall face PVC (D-plast) accessories for rain water pipes of Supreme/Finolex/Prince /Relpipe (reliance)/ vectus including filling the joints with approved adhesive complete as per PWD specification, approved drawing and design including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer- in-Charge Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government. |
| 59 | Providing and fixing on wall face 150 mm (One hundred tenfifty millimetre) diametre shoe Providing and fixing on wall face PVC (D-plast) accessories for rain water pipes of Supreme/Finolex/Prince /Relpipe (reliance) vectus including filling the joints with approved adhesive complete as per PWD specification, approved drawing and design including cost and carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer- in-Charge Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government. |
| 60 | Providing and fixing unplasticised PVC Pipe clips / Clamps of Supreme/Finolex/ Prince/Relpipe (reliance)vectus of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm (Fifty by Fifty by Fifty milimetres) hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete including carriage of material within all leads, lifts and other incidentals. Rate is inclusive of sale tax, toll tax, GST and any other taxes imposed by the government. |
| 61 | Steel work welded in built up sections of TATA/SAIL joists channels, angles, tees with connection plates or angles, cleat as in trusses, trussed purlins main and cross beams, hips jack rafters, purlins connected to common rafters and the like in building including cutting, fixing, lifting, hoisting and; placing in position complete and applying a coat of red lead paint, within all leads, lifts of materials and other incidentals. as per approved architectural drawing, design and specification as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 62 | Painting two or more coats (excluding priming coat) on new steel and other metal surfaces with enamel paint brushing of Asian paint/ Nerolac/Berger of approved shade to give an even shade including cleaning the surfaces of all dirt, dust andother foreign matter enamel paint other than white within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 63 | 6mm (Six milimetres) thick cement plaster in ceiling with cement mortar 1:3 (One cement: Three sand) for all heights within all leads, lifts of materials and other incidentals as per approved approved specification, drawings and design. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 64 | 15mm (Fifteen milimetres) thick cement plaster in single coat on rough side of brick/concrete/stone walls for interior plastering upto all floor levels including arises internal rounded angles, chamfers and or rounded angles not exceeding 80mm (Eighty milimetres) in girth and finished even and smooth with cement mortar 1:6 (One cement isto six sand) within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 65 | 15mm (Fifteen milimetres) thick cement plaster in single coat on fair side of brick/concrete/ stone walls for interior plastering upto all floor levels including arises internal rounded angles, chamfers and or rounded angles not exceeding 80mm (Eighty milimetres) in girth and finished even and smooth with cement mortar 1:6 (One cement isto six sand) within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 66 | 15mm (Fifteen milimetres) thick cement plaster in single coat on fair side of brick/concrete/ stone walls for exterior plastering upto two floor levels including arises internal rounded angles, chamfers and or rounded angles not exceeding 80mm (Eighty milimetres) in girth and finished even and smooth with cement mortar 1:4 (One cement isto four sand) within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 67 | 20 MM Cement patten in plaster with cement Mortar 1:4 (One Cement four coarse sand ) complete as per Architectural drawing, specification within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 68 | Applying Birla / J.K white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 69 | Providing and laying Dr. Fixit torch shield (IP-3160-3mm) shall be used for water proofing treatment on terrace/depressed portion membrances are made from high grade bitumen and selected polymers, APP/SBS modified bitumen thin coated to non-woven polyster reinforcement to give high care and puncher resistance. The application shall be done as per Architectural drawing, specification within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 70 | Finishing walls with Apex weather proof exterior emulsion paint of Asian / Dulux / Berger / Nerolac Suraksha paints of approved shade having VOC less than 50 gm/litre (Fifty gram per litre) and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives. New work (Two or more coats applied @ 1.43 litre/ 10 sqm (One point forty three litre per ten square metre) Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm (Zero point Nine zero litre per ten square metre) complete as per Architectural drawing ,design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 71 | Distempering (two coats) with acrylic distemper with Nerolac/ Asian paints of approved brand and manufacture and of required shade on ceiling/sloping roof surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth.Priming coat with distemper primer within all leads, lifts of materials and other incidentals. as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 72 | Wall painting with premium acrylic emulsion paint of Asian / Dulux / Berger / Nerolac Suraksha paints of approved interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour two or more coats, as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 73 | Finishing walls with Acrylic Smooth exterior paint of Asian / Dulax / Berger / Nerolac Suraksha paint of required shade New work (Two or more coat applied @ 1.67 ltr/10 sqm ( one decimal sixty seven litre per ten squaremetre) over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm ( two decimal twenty kilogram per ten squaremetre) , as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 74 | Providing Plinth protection with 40 mm (forty millimetre) thick interlocking paver blocks of NTC with 23 cm (twenty three centimetre) dia. Half round R.C.C. pipe for drainage purpose laid base over of 10 cms ( ten centimetre) thickness cement concrete 1:4:8 (one cement isto four sand isto eight graded / crushed stone aggregate) 40mm (forty millimetre) nominal size for bedding of pipe complete within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 75 | Providing and laying 12mm (twelve millimetre) thick Unistone / NTC / Atlantic tile cladding on wall surface with 12mm ( twelve millimetre) thick cement mortar 1:3 (one cement isto three sand) and jointed with cement slurry to match the stone including scaffolding and cost and carriage of material as per approved drawing, design including carriage of materials within all leads, lifts and other incidental, and as per directions of Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 76 | Providing and laying 60 mm thick Interlocking M-40 grade Concrete paver block pavement confirming to ISI 15658:2006 having thickness 60mm (sixty millimetre) as per drawings and Technical Specification Clause 1504 (The execution of interlocking paver block shell be allowed after duly testing from the authorized labs) and as per the directions of Engineer-In-Charge including carriage of materials within all leads, lifts and other incidental. The rate is including octroi, royality, GST, toll tax, or other taxes imposed by the Government. |
| 77 | Providing and fixing panneling of 8 mm (eight millimetre) thick teak ply over 50x31 mm (fifty into thirty one millimetre) soft wood frame at 600 mm C/C (six hundred millimetre centr to centre) with decorative teak wood beading over teak ply of size 25x12 mm (twenty five into twelve millimetre) having moulding on both side cornice/ edging on top of paneling to be finished with 55x30 mm (fifty five into thirty millimetre) teak wood beading, including carriage of material within all leads, lifts and other incidentals as per approved drawing, design, specifications and as directed by Engineer-In-Charge. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 78 | Providing and fixing polythelene aluminum polythelene (PE- AL-PE) composite pressure pipe U.V. stabilized with carbon block confirming to I.S. 15450-2004 of Kitec for water supply including clamps at appropriate spacing, cutting fixing and making good the walls etcetera; but excluding the cost of fittings (Internal work), including filling the joints with approved adhesive complete including entire carriage of materials within all leads lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 79 | 1620 (20mm) twenty millimeter diameter pipe O.D. pipe |
| 80 | 2025 (25mm) twenty five millimeter diameter pipe O.D. pipe |
| 81 | Making connection of galvanized mild steel distribution branch with galvanized mild steel main 20mm to 40nmm (Twenty milimetres to Forty milimetres)nominal bore by providing and fixing tees including cutting and threading the pipe complete including entire carriage of materials within all leads lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 82 | Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes light grade ISI marked of fenolex/vectus/price 4.6mm thick having pressure not less than 6kg /cm2 (six kilogramm per centimetre square) including fixing with approved adhesive etc. complete including entire carriage of materials within all leads lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 83 | 110mm (One hundred ten milimetres) diametres |
| 84 | 75mm (Seventy milimetres) diametres |
| 85 | Providing and fixing cast iron P.V.C. holder bat clamps ISI marked of approved drawing i/c/ steel screw and rawl plug etc. including entire carriage of materials within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 86 | 110mm (One hundred ten milimetres) diametres |
| 87 | 75mm (Seventy milimetres) diametres |
| 88 | Providing and fixing P.V.C. I.S.I. marked heal rest of Finolex / Supreme / Prince including filling the joints with including fixing with approved adhesive within all leads, lifts of materials and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 89 | 110mm (One hundred ten milimetres) diametres |
| 90 | 75mm (Seventy milimetres) diametres |
| 91 | Providing and fixing P.V.C. I.S.I. marked plain bend of Finolex / Vectus / Prince including filling the joints with including fixing with approved adhesive within all leads, lifts of materials and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 92 | 110mm (One hundred ten milimetres) diametres |
| 93 | 75mm (Seventy milimetres) diametres |
| 94 | Providing and fixing P.V.C. Collar ISI marked of Finolex / Supreme / Prince including fixing with approved adhesive complete, within all leads, lifts of materials and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 95 | 110mm (One hundred ten milimetres) diametres |
| 96 | 75mm (Seventy milimetres) diametres |
| 97 | Providing and fixing P.V.C. I.S.I. marked cowl (confirming to BIS-14735-99) ISI marked of Finolex / Supreme / Prince including fixing with approved adhesive complete, within all leads, lifts of materials and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 98 | 110mm (One hundred ten milimetres) diametres |
| 99 | 75mm (Seventy milimetres) diametres |
| 100 | Providing and fixing 110 x 90mm (One hundred ten into Ninety milimetres) P.V.C. I.S.I. marked floor trap of Finolex / Supreme / Prince ISI marked (confirming to BIS-14735-99) of self cleaning design including with approved adhesive cost of cutting and making good walls and floors complete, within all leads, lifts of materials and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 101 | Providing and fixing 110 x 75mm (One hundred ten into Seventy five milimetres) P.V.C. I.S.I. marked floor trap of Finolex / Supreme / Prince ISI marked (confirming to BIS-14735-99) of self cleaning design including with approved adhesive cost of cutting and making good walls and floors complete, within all leads, lifts of materials and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 102 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) White Vitreous china Orissa pattern W.C. pan no 20090 of size 530x410 mm ( five hundred thirty into four hundred ten milimetres) with integral type foot rests with 100 mm ( one hundred milimetres) sand cast Iron P or S trap, 10 litre low level P.V.C. flushing cistern,of Hindware , Cera ,Jaquar of star white / Snow white shade and as shown in the drawing / as per details including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentalsThe rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 103 | Providing and fixing white vitreous china pedestal type water closet (European type) No 20087 (S - 10 ) Size 57 X 35 X 39 cm ( fifty seven into thirty five into thirty nine centimetres) with seat and lid, 10 (ten) litre low level white vitreous china flushing cistern (sleek Plus) Hindware , Cera ,Jaquar of star white / Snow white shade and as shown in the drawing / as per details & C.P. flush bend with fittings & C.I. brackets, 40 mm ( forty milimetres) flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid each as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 104 | Providing and fixing white vitreous china pedestal type Matrix water closet (European type) with seat and lid, 10 (ten ) litre low level white vitreous china flushing cistern Hindware , Cera ,Jaquar of star white / Snow white shade and as shown in the drawing / as per details & C.P. flush bend with fittings & C.I. brackets, 40 mm ( forty milimetres) flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. . The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 105 | Providing and fixing wash basin White Vitreous China Flat back wash basin Garnet no 10080 size 580x 430 mm ( five hundred eighty into four hundred thirty) ( Under counter Basin ) Hindware , Cera ,Jaquar of star white / Snow white shade and as shown in the drawing / as per details with single 15 mm ( Fifteen milimetres) C.P. brass pillar tap with C.I. brackets, 15 mm ( fifteen milimetres) C.P. brass pillar taps, 32 mm ( Thrity two milimetres) C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 106 | Providing and fixing vitreous china pedestal of Cera / Hindware/jaguar for wash basin complete having recessed at the back for the receiption of pipe and fittings. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 107 | Providing and fixing wash basin White Vitreous China Flat back wash basin Garnet no 10080 size 580x 430 mm ( five hundred eighty into four hundred thirty) Hindware , Cera ,Jaquar of star white / Snow white shade and as shown in the drawing / as per details with single 15 mm ( Fifteen milimetres) C.P. brass pillar tap with C.I. brackets, 15 mm ( fifteen milimetres) C.P. brass pillar taps, 32 mm ( Thrity two milimetres) C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 108 | Providing and fixing white vitreous china flat back half stall urinal no 60002 of size 39 x 37.5 x 59 cm ( thrity nine into thirty seven decimal five into fifty nine centimetres) with white PVC automatic flushing cistern of Hindware , Cera ,Jaquar of star white / Snow white shade and as shown in the drawing / as per details with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required Range of two half stall urinals with 5 (five litre P.V.C. automatic flushing cistern each 10188.90 as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 109 | Providing and fixing 32mm (Thirty two millimetres) nominal size diametres rubber plug for wash basin within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 110 | Providing and fixing 32mm diameter P.V.C. waste pipe Supreme/finolex/prince waste pipe for wash basin or sink including brass check nut. The rate is inclusive of octroi, royality, malkana, toll tax, GST and all type of other taxes imposed by the Government. |
| 111 | Providing and fixing 100mm (One hundred millimetres) diametres C.P. (Chromium plated) Grating ISI Marked IS No. 8934 (Eight thousand nine hundred thirty four) of Continental series of Jaquar / Classik series of Hindware/ Floral series of Cera & Hindon series of Jal for gully floor or Nahni trap as per H.P.P.W.D specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 112 | Providing and fixing flat back 600x450mm (Six hundred into Four hundred fifty millimetres) beveled edge mirror of Atul/ Modi Guard/ Goldex Fish of superior glass of approved quality complete with mounted on 6mm (Six millimetres) thick A.C. asbestos cement sheet or ply wood sheet and fixed to wooden plugs with C.P. (Chromium plated) brass screws and washers complete as per H.P.P.W.D specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals.The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 113 | Providing and fixing 600mmx20mm (Six hundred millimetre into Twenty millimetres) C.P. (Chromium plated) ISI Marked IS No. 8934 (Eight thousand nine hundred thirty four) of Continental series of Jaquar / Classik series of Hindware/ Floral series of Cera & Hindon series of Jal brass Towel rail with C.P. (Chromium plated) brass brackets fixed to wooden plugs with C.P.(Chromium plated) brass screws complete as per H.P.P.W.D specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 114 | Providing and fixing chromium plated brass soap dish of Jal/ Jaquar/ ESS ESS with C.P. Brass brackets fixed to wooden cleats with C.P. Brass screws complete as per the entire satisfaction and direction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government. |
| 115 | Providing and fixing C.P. brass each toilet paper holder of Continental series of Jaquar / Contess plus series of Hindware /floral series of Cera / Vintage series of Kerovite & Hindon series of Jal as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 116 | Providing and fixing 8mm dia C.P. jet spray of Continental series of Jaquar / Classik series of Hindware / Floral Series of Cera / Hindon series of Jal of approved quality and colour with one metre tube within all leads, lifts of materials and other incidentals and as directed by the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 117 | Providing and fixing 15mm dia (Fifteen millimetres) diametres nominal bore chromium plated brass (ISI marked No. 8934) (Eight thousand nine hundred thirty four) bib tap (superior or heavy type) of Continental series of Jaquar / Classik series of Hindware / Floral Series of Cera / Hindon series of Jal as per H.P.P.W.D specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 118 | Providing and fixing 15mm dia (Fifteen millimetres) diametres C.P. (chromium plated) brass stop cock Conforming ISI Marked IS No. 8934 (Eight thousand nine hundred thirty four) of Continental series of Jaquar / Classik series of Hindware / Floral Series of Cera / Hindon series of Jal as per H.P.P.W.D specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 119 | Providing and fixing 15mm dia (Fifteen millimetres) diametres C.P. ( chromium plated) brass pillar tap with capstan head Conforming to IS: 8934 (Eight thousand nine hundred thirty four) of Continental series of Jaquar / Classik series of Hindware / Floral Series of Cera / Hindon series of Jal as per H.P.P.W.D specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 120 | Providing and fixing 15mm dia (Fifteen millimetres) diametres C.P. (chromium plated) push cock Conforming ISI Marked IS No. 8934 (Eight thousand nine hundred thirty four) of Continental series of Jaquar / Classik series of Hindware / Floral Series of Cera / Hindon series of Jal as per H.P.P.W.D specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 121 | Providing and fixing 15mm (Fifteen milimetres) diametres C.P.brass angle valve without nuts of Continental series of Jaquar / Classik series of Hindware / Floral Series of Cera / Hindon series of Jal as per approved drawing and design directed by the Engineer-in-Charge within all leads, lifts of materials and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 122 | Providing and fixing 15mm (Fifteen milimetres) nominal bore C.P. brass full valve of Continental series of Jaquar / Classik series of Hindware / Floral Series of Cera / Hindon series of Jal within all leads, lifts of materials and other incidentals and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 123 | Providing and placing water tank make P.V.C. SINTEX three layer having capacity of 1000 ( One thousand) liters each tank with necessary fittings including over flow pipe scour pipe etcetera and pads required for in let and out let ball valve with cover and locking arrangements complete in all respect within all leads, lifts of materials and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 124 | Providing and laying cement concrete 1:5:10(1 Cement : 5 Sand : 10 graded stone aggregate 40mm nominal size ) in haunching of PVC. pipes of 150mm internal diameters, including concrete for beddings necessary form work and curing complete.within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 125 | Providing and fixing 600mmx120mmx5mm (Six hundred millimetres into One hundred twenty into five millimetres) glass shelf of ISI No. 8934 (Eight thousand nine hundred thirty four) of Continental series of Jaquar / Classik series of Hindware/ Floral series of Cera & Hindon series of Jal make brackets and guard rail fixed to wooden plugs with C.P.(Chromium plated) brass screws complete as per H.P.P.W.D specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 126 | Providing and fixing 600mmx300mm (six hundred into three hundred millimetres) white vitreous china Division plate of Hindware , Cera ,Jaquar of star white / Snow white shade and as shown in the drawing / as per details urinal with integral rim longitudinal flush pipe. as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 127 | Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III): 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design Inside size 900x800mm (Nine hundred into Eight hundred millimetres) and 450mm (Four hundred fifty milimetres) deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg With Sewer bricks conforming to IS : 4885 as per H.P.P.W.D specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 128 | Constructing brick masonry chamber for under ground C.I. (Cast iron) inspection chamber and bends with common burnt clay building bricks in cement mortar 1:4(One cement isto Four sand) C.I. (cast iron) cover with frame(light duty) 455x610mm (Four hundred fifty five into Six hundred ten millimetres)internal dimensions total weight of cover and frame to be not less than 38Kgs (Thirty eight Kilograms) weight of cover 23 Kgs (twenty three kilograms)and weight of frame 15 Kgs (Fifteen kilograms) RCC (Reinforced cement concrete) top slab with 1:2:4 (One cement isto Two sand isto Four graded crushed stone aggregate 20mm (Twenty millimetres) nominal size mix foundation concrete 1:5:10 (One cement isto Five sand isto Ten graded crushed/broken stone aggregate 40mm(Forty millimetres nominal size) inside plaster 15mm ( Fifteen millimetres) thick with cement mortar 1:3 ( One Cement isto three sand) finished smooth with a floating coat of neat cement on walls and bed concrete etcetera. complete inside dimensions 455x610mmx450mm (Four hundred fifty five into Six hundred ten into Four hundred fifty millimetres) deep single pipe line as per H.P.P.W.D specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. |
| 129 | Excavating trenches of required width for pipes, cables etc including excavation for sockets and dressing of sides ramming of bottoms depth upto 1.5 m, including getting out the excavated soil and then returning the soil as required in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 metre for Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia complete.within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. Please Enable Macros to View BoQ information |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
