|
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m i/c carriage of material in all leads and lifts. All kinds of soil. |
| 2 | Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge: including carriage of material in all leads and lifts. All kinds of soil. |
| 3 | Providing and laying in position mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix,but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-incharge.“( Note :- Cement content considered in this item is @ 330 kg/cum.“Excess/ less cement used as per design mix is payable/recoverable separately).All works above plinth level upto floor V level |
| 4 | All works upto plinth level |
| 5 | Providing and laying cement concrete 1:6:12(1cement:6 sand :12 graded stone aggregate 40 mm nominal size) and curing complete excluding cost of form work in foundation and plinth including carriage of material in all leads and lifts. |
| 6 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) i/c carriage of material in all leads and lifts. |
| 7 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:2:4 (1 cement : 2 coarse sand) : 4 graded stone aggregate 20 mm nominal size) :including carriage of material in all leads and lifts. |
| 8 | Centering and shuttering including strutting, propping etc. and removal of form for: |
| 9 | Suspended floors, roofs, landings, balconies and access platform |
| 10 | Shelves (Cast in situ) |
| 11 | Lintels, beams,plinth beams, girders, bressumers and cantilevers. |
| 12 | Columns, Pillars, Piers, Abutments, Post sand Struts |
| 13 | Stairs, (excluding landings) except spiral staircases |
| 14 | Edges of slabs and breaks in floors and walls, under 20Cm wide |
| 15 | Weather shade, Chajjas, corbels etc., including edges |
| 16 | Steel reinforcement for R.C.C work including straightening, cutting,bending, placing in position and binding all complete above plinth level. TMT bars of grade Fe-500D or more i/c carriage of material in all leads and lifts. |
| 17 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand) i/c carriage of material in all leads and lifts. |
| 18 | Brick work 7 cm thick with common burnt clay F.P.S. (non modular) brick of class designation 7.5 in cement mortar 1:3 (1 cement : 3 coarse sand) in superstructure above plinth level and upto floor five level i/c carriage of material in all leads and lifts. |
| 19 | Centering and shuttering including strutting, propping etc. and removal of form for: |
| 20 | Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 21 | Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 22 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor all level Cement mortar 1:4 (1 cement :4 coarse sand) inlcuding carriage of material in all leads and lifts. |
| 23 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, mouldingand polishing to edges to give high gloss finish etc. complete at all levels.Granite of any colour and shade i/c carriage of material in all leads and lifts. |
| 24 | Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete i/c carriage of material in all leads and lifts. |
| 25 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. i/c carriage of material in all leads and lifts. 40 mm thick with 20 mm nominal size stone aggregate |
| 26 | Providing and fixing 10mm thick anti skid water proof stain and impect resistent heavy duty vetrified tiles any size/colour manufactured of approved shade and colour in flooring, treads of steps and landings laid over 12mm thick cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete including carriage of material in all leads & lifts. |
| 27 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineerin- Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete i/c carirage of material in all leads and lifts. |
| 28 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shallbe paid for separately) i/c carriage of material in all leads and lifts. Second class deodar wood |
| 29 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1stclass hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters i/c carriage of material in all leads and lift.35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 30 | Providing and fixing panelling and glazing in panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for npanel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick 2nd Class deodar wood :Float glass panes mm thick glass pane (weight not less than 10 kg per sqm) i/c carriage of material in all leads and lift. |
| 31 | Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 60 mm thick C.C. paver block of M-35 grade with approved colour design & pattern |
| 32 | Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete : i/c carriage of material in all leads and lifts.300x16 mm |
| 33 | Providing and fixing ISI marked oxidised M.S. handlesconforming to IS:4992 with necessary screws etc. complete : |
| 34 | Providing and fixing ISI marked oxidised M.S. tower boltblack finish, (Barrel type) with necessary screws etc. complete : i/c carriage of material in all leads and lifts. |
| 35 | Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using flats 30x6mm for diagonal braces and central cross piece |
| 36 | Providing and fixing stainless steel powder coated sliding door bolts of required color and shade with bolts and nuts, screws etc complete including carriage of material in all leads and lifts. 300x16 mm |
| 37 | Providing and fixing stainless steel powder coated handles to required colour and shade with necessary screws, etc. complete including carriage of material in all leads and lifts. |
| 38 | 125 mm |
| 39 | 100 mm |
| 40 | Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete i/c carriage of material in all leads and lifts. |
| 41 | Providing and fixing stainless steel powder coated Tower bolts of required color and shade with bolts and nuts, screws etc complete including carriage of material in all leads and lifts. |
| 42 | 200X10 mm |
| 43 | 150X10 mm |
| 44 | Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete : 2nd class teak wood50x20 mm i/c carriage of material in all leads and lifts. |
| 45 | Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete : 2nd class teak wood50x20 mm i/c carriage of material in all leads and lifts. |
| 46 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required i/c carriage of material in all leads and lifts. |
| 47 | In stringers, treads, landings etc. of stair cases, including use of chequered platewherever required, all complete |
| 48 | In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 49 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc. complete i/c carriage of material in all leads and lifts. Size of tile 600X600 mm |
| 50 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. i/c carriage of material in all leads and lifts. Size of tile 600X600 mm |
| 51 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as perIS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required i/c carriage of material in all leads and lifts. |
| 52 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required i/c carriage of material in all leads and lifts. |
| 53 | Ridges plain (500 - 600mm) |
| 54 | Flashings/ Aprons.( Upto 600 mm) |
| 55 | Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main \\"T\\" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross \\"T\\" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main \\"T\\" at 600mm center to center to form a grid of 1200x600 mm and secondary cross \\"T\\" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to formgrids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smokedetectors etc. Main \\"T\\" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanisedbutterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be prepainted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge.(a)12.5 mm thick fully Perforated Gypsum Board tile made from plasterboard having glass fibre conforming to IS: 2095 part I, of size 595x595 mm, having perforation of 9.7x9.7 mm at 19.4 mm c/c with center borders of 48 mm and the side borders of 30 mm, backed with non woven tissue on the back side, having an NRC (Noise Reduction Coefficient) of 0.79, with 50 mm resinbonded glass wool backing |
| 56 | 15 mm cement plaster on rough side of single or half brick wall of mix upto all heights/depths in mement Mortor 1:6 (1 cement: 6 coarse sand).i/c carriage of material in all leads & lifts |
| 57 | 1Cement mortar 1:4 (1 cement: 4 fine sand) |
| 58 | 20 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand) upto all heights i/c carriage of material in all leads & lifts. |
| 59 | 6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand) upto any height /Depth i/c carriage of material in all leads & lifs. |
| 60 | Neat cement punning as per direction of Engineer-in-charge i/c carriage of material in all leads and lifts. |
| 61 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade: New work (two or more coats) over and including water thinnable priming coat with cement primer including carriage of material in all leads & lifts |
| 62 | Finishing with Delux Multi surface paint system for interiors and exteriors using primer as per manufacturers specifications: Painting steel work with Delux Multi surface paint to give an even shade. Two or more coat applied @0.90 ltr/10 sqm over an under coat of primer applied @0.80ltr/10 sqm of approved brand and manufacturer. |
| 63 | Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives.New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm including carriage of material in all leads & lifts. |
| 64 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in charge Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 65 | roviding and fixing M.S. angle 40x40x5 mm to act as nosing with lugs of M.S. flat 10x5 mm, 10 cm long, forked at end 60cm apart (minimum three lugs to be provided), including necessary welding and applying a priming coat of approved primer on exposed surface etc. complete i/c carriage of material in all leads and lifts. |
| 66 | Providing and applying white cement based putty of average thickness 1mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete including carriage of material in all leads & lifts. |
| 67 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, includingflush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid |
| 68 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests |
| 69 | Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required :i/c carriage of material in all leads and lifts. Single half stall urinal with 5 litre P.V.C. automatic flushing cistern i/c carriage of material in all leads and lifts. |
| 70 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap i/c carriage of material in all leads and lifts. |
| 71 | Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings i/c carriage of material in all leads and lifts. |
| 72 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge i/c carriage of material in all leads and lifts. |
| 73 | Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required :Size 600x450x200 mm , i/c carriage of material in all leads and lifts. |
| 74 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete Flexible pipe i/c carriage of material in all leads & lifts.40 mm dia |
| 75 | Providing and fixing 100 mm dia cromium plated stainless steel grating confirming to BIS specifcation including carriage of material in all leads and lifts. |
| 76 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete i/c carriage of material in all leads and lifts. |
| 77 | Providing and fixing 600X120X5mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P brass brackets and guard rail complete fixed with 40 mm long screws, rawl puls etc. complete i/c carriage of material in all leads and lifts. |
| 78 | Providing and fixing C.P. Brass towel ring make as approved by Engineer - in - charge i/c carriage of material in all leads and lifts. |
| 79 | Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms i/c carriage of material in all leads and lifts. |
| 80 | Providing and fixing PVC floor trap ISI marked or self cleaning design including fixing eith approved adhesive, cost of cutting and making good the wall and floors etc. complete. 110X90mm |
| 81 | Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete i/c carriage of material in all leads and lifts.90 mm dia |
| 82 | 110 mm dia |
| 83 | Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete i/c carriage of material in all leads and lifts.90 mm dia |
| 84 | 110 mm dia |
| 85 | Providing and fixing PVC door bend ISI marked including fixing with approved adhesive etc. complete.90 mm dia |
| 86 | Providing and fixing PVC cowl complete including fixing with approved adhesive etc. complete. i/c carriage of magterial in all leads and lifts. 110 mm dia |
| 87 | Making connection of G.I distribution branch with G.I main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete. (a) 25 to 40 mm nominal bore. |
| 88 | Providing and fixing brass stop cock of approved quality i/c carriage of material in all leads and lifts. 15 mm nominal bore. |
| 89 | Providing and fixing uplasticised PVC connection pipe with brass unions : 15 mm nominal bore (a) 45 cm length |
| 90 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank i/c carriage of material in all leads and lifts. |
| 91 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 complete i/c carriage of material in all leads and lifts. 15 mm nominal bore |
| 92 | Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :Inside size 90x80 cm and 45 cm deep including SFRC M.H.. cover with frame (Heavy duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 182 kg : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 i/c carriage of material in all leads and lifts. |
| 93 | Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design 100x100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 i/c carriage of material in all leads and lifs.tion 7.5 i/c carriage of material in all leads and lifts. |
| 94 | Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 95 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete i/c carriage of material in all leads and lifts. Fixed to openings /wooden frames with rawl plugs screws etc. |
| 96 | Providing 40X5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nutsm and wooden plugs and embedding in cement concrete block 30X10X15 cm 1:3:6 mix (1 cement:3 coarse sand : 6 graded stone aggregate 20 mm nominal size) i/c carriage of material in all leads and lifts. |
| 97 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. i/c carriage of material in all leads and lifts. 15 mm nominal bore. |
| 98 | Providing and fixing G.I. Union in existing G.I. pipe line, cutting and threading the pipe and making long screws, including excavation, refilling the earth or cutting of wall and making good the same complete wherever required i/c carriage of material in all leads and lifts.15 mm nominal bore |
| 99 | Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms i/c carriage of material in all leads and lifts. 15 mm nominal bore |
| 100 | Providing and fixing glazed shutters for windows and clerestory windows using 4 mm thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws i/c carriage of material in all leads and lifts.2nd class deodar wood. |
| 101 | Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing Tiron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete as per the direction of Engineer-In-charge. |
| 102 | Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality Rectangular shape 600x450 mm internal dimensions |
| 103 | Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws i/c carriage of material in all leads and lifts. 35 mm thick 2nd class deodar wood |
| 104 | Finishing with Delux Multi surface paint system for interiors and exteriors using primer as per manufacturers specifications:Painting wood work with Delux Multi surface paint of required shade. Two or more more coat applied @0.90 ltr/10 Sqm over an under coat of primer applied @ 0.75 ltr/10 sqm of approved brand and manufature i/c carriage of material in all leads and lifts. |
| 105 | Providing and fixing Chest Press Technical Specification Size 2500X 800X 2000 Main frame 100mm OD GI pipe Frame & Handle- 40mm & 31mm OD G.I. pipe. Metal Paint:Powder Coated. All open ends of pipe are to be close by GI/PVC caps for user safety against entrapment. i/c civil work and carriage of material in all leads and lifts. |
| 106 | Providing and fixing Wheel/ Shoulder Twirl Technical Specification: Size 1450X 520X 1750 Main frame 80mm OD GI pipe Frame & Handle-25mm OD G.I. pipe. Metal Paint:Powder Coated. All open ends of pipe are to be close by GI/PVC caps for user safety against entrapment. i/c civil work and carriage of material in all leads and lifts. |
| 107 | Providing and fixing HandRower Technical Specification: Size 1200X 800X 700 Main frame: 100mm OD GI pipe Structure: 80mm OD G.I. pipe. movement: 31mm OD G.I.pipe Handle: 25mm OD G.I. pipe. Metal Paint:Powder Coated. All open ends of pipe are to be close by GI/PVC caps for user safety against entrapment. i/c civil work and carriage of material in all leads and lifts. |
| 108 | Providing and fixing Back Extension Technical Specification: Size 1060X 730X 990mm Main frame 100mm OD GI pipe Foundation plate-M.S. Round Plate of 250mm and 8mm Thick or more Seat Rest Pipe / Seat : GI Pipe 42mm OD or more Seat Rest and Foot Rest: Perforated Galvanished Seat Having Wall Thickness of 2mm as per standred. Metal Paint:Powder Coated. All open ends of pipe are to be close by GI/PVC caps for user safety against entrapment. i/c civil work and carriage of material in all leads and lifts. |
| 109 | Providing and fixing Shoulder Exerciser Technical Specification:Size 1600X 300X1200 Main frame: 80mm OD GI pipe Structure: 31mm& 25mm OD G.I. pipe. Handle: 25mm OD G.I. pipe Revolving Seat : MS Sheet. Metal Paint:Powder Coated. All open ends of pipe are to be close by GI/PVC caps for user safety against entrapment. i/c civil work and carriage of material in all leads and lifts. |
| 110 | Providing and fixing Aerial Stroller Technical Specification:Size 100X 550X1480 Main frame: 100mm OD GI pipe PipeU: 80mm OD G.I. pipe. Leg movement:40mm OD G.I.pipe Handle: 31mm OD G.I. pipe. Metal Paint:Powder Coated. All open ends of pipe are tobe close by GI/PVC caps for user safety against entrapment. i/c civil work and carriage of material in all leads and lifts. |
| 111 | Providing and fixing Leg Extension Technical Specification:Size 1060 MM X 730 MM X 990 MM or as per manufacturer design Main frame 100 MM or more Foundation plate-M.S. Round Plate of 250mm and 8mm Thick or more Arm handle & Rest Seat frame :32/50 NB GI Pipe With 2.65mm Thickness as per standard design Back & Rest Seat & Foot Rest: Perforated Galvanished Seat Having Wall Thickness of 2mm with Precision Punched Hole of 10mm Dia / Cast Iron 325 x 270 x 8 mm thick and M.S Plate of 250 x 200 x 2mm Thick as per standard design Handle Pipe: 33mm OD GI Pipe or more Leg Support :42mm OD GI Pipe or more Seat Rest Pipe: 42mm OD GI Pipe or more Foot Rest Pipe : 42mm OD G.I. Pipe and 80 x 40 mm MS Rectangular Pipe. Metal Paint:Powder Coated. All open ends of pipe are to be close by GI/PVC caps for user safety against entrapment. i/c civil work and carriage of material in all leads and lifts. |
| 112 | Providing and fixing Sky Walker Technical specification: Size 850X800 X 1800 Main frame: 80mm OD GI pipe Leg movement:40mm OD G.I.pipe Handle & Leg: 31mm & 25mm OD G.I. pipe Foor rest : MS Sheet2mm. Metal Paint:Powder Coated. All open ends of pipe are to be close by GI/PVC caps for user safety against entrapment. i/c civil work and carriage of material in all leads and lifts. |
| 113 | Providing and fixing HIP Twister Circular Double Technical specification: Size 1700X1300X1300 Main frame: 80mm OD GI pipe Plate Leg:40mm OD G.I.pipe Handle : 25mm OD G.I. pipe Revolving Plates : MS Sheet. Metal Paint:Powder Coated. All open ends of pipe are to be close by GI/PVC caps for user safety against entrapment. i/c civil work and carriage of material in all leads and lifts. |
| 114 | Providing and fixing Arm Extension Technical specification: Discription: Arm Wheel Dimensions 3 x 2 x 6 (feet) Main Pipe 114MM OD Metal Pipe Supporting Pipe 34MM, 27MM OD Metal Pipe Workout Type Wheel Rotation. Metal Paint:Powder Coated. All open ends of pipe are to be close by GI/ PVC caps for user safety against entrapment. i/c civil work and carriage of material in all leads and lifts. |
| 115 | Providing and fixing Pull up Bars Technical specification: Discription: Chinup Stand Dimensions 3.5 x 1.5 x 4 Ft.Main Pipe 75mm OD Metal Pipe Supporting Pipe 48MM, 34MM OD Metal Pipe Metal Paint: Powder Coated All open ends of pipe are to be close by GI/PVC caps for user safety against entrapment. i/c civil work and carriage of material in all leads and lifts. |
| 116 | Providing and fixing Double seated Pull Chair Technical specification: Discription: Seated Puller Dimensions 3x 2.75 x 7 (feet) STATION : 2 Main Pipe 114mm OD Metal Pipe (3mm Thickness) Supporting Pipe 48MM OD Metal Pipe and 40x40 Metal Box Seat/Back Rotomoulded /Metal Metal Paint:Powder Coated. All open ends of pipe are to be close by GI/PVC capsfor user safety against entrapment. i/c civil work and carriage of material in all leads and lifts. |
| 117 | Providing and fixing Paraller Bar Monkey Bar Discription: Monky BarDimensions 8 x 3 x 7 Ft. Main Pipe 75mm OD Metal Pipe Supporting Pipe 48MM, 34MM OD Metal Pipe Metal Paint:Powder Coated. All open ends of pipe are to be close by GI/PVC caps for user safety against entrapment. i/c civil work and carriage of material in all leads and lifts. Please Enable Macros to View BoQ information |
