|
| 1 | Earth work in excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge. All kinds of soil. |
| 2 | Hard rock ( Blasting prohibated ) |
| 3 | Earth work in excavation by mechanical means (Hydraulic excavator) infoundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed,within a lead of 50 m. All kinds of soil. |
| 4 | Hard rock Hard rock ( Blasting prohibated ) |
| 5 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. |
| 6 | Dumping stone in horizontal level including cost of stone . |
| 7 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work upto plinth level 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 8 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished 50 mm thick with 20 mm nominal size stone aggregate |
| 9 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 10 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size) |
| 11 | Providing & fixing stabilized mud concrete solid blocks (adobe) with 3% cement, masonry up to floor five level including hoisting and setting in position in mud mortar using approved quality mud with carriage ofmaterial complete. |
| 12 | Providing and fixing up to floor five level precast cement concrete solid block,including hoisting and setting in position with cement mortar 1:3 (1 cement : 3 coarse sand), cost of required centering, shuttering complete :1:3:6 (1 Cement: 3 coarse sand(zone-III) : 6 graded stone aggregate 20 mm nominal size). |
| 13 | Random Rubble masonry with hard stone in foundation and plinth including leveling up with cement concrete 1:6:12 (1 Cement : 6 coarse sand : 12 graded stone aggregate 20mm nominal size) upto plinth level and curing complete with: Cement mortar 1:6 (1 Cement : 6 coarse sand) |
| 14 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): second class kail wood |
| 15 | Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately) 35mm thick 2nd class teak wood, |
| 16 | Providing and fixing traditionally carved wood work (Shingstak) over doors and windows including all accessories as per the direction of the Engineer in-charge, complete with;Local willow wood |
| 17 | Providing and fixing 35 mm thick factory made laminated veneer lumber doorshutter conforming to IS : 14616 and TADS 15:2001 (Part B) fixing with butthinges of required size with necessary screws, all complete as per directions ofEngineer- in-charge and panelling with panels of : (Note:- Butt hinges andnecessary screws shall be paid separately)12 mm thick pre-laminated particle board (decorative lamination on both sides)grade -1, medium density flat pressed, three layer particle board FPT- I or gradedwood particle board FPT- I, conforming to IS : 3087, bonded with BWP typesynthetic resin adhesive as per IS : 848 and pre-laminated conforming to IS :12823, Grade 1, Type - II marked : |
| 18 | French spirit polishing with Two or more coats on new works including a coat of wood filler |
| 19 | Providing and fixing stainless steel fancy handle of approved make fixed with SS screws etc. complete as per direction of Engineer-in-charge. 200mm |
| 20 | Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : 150 x 10mm |
| 21 | 100x10 mm |
| 22 | Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete :300 x 16mm |
| 23 | Providing and fixing 150 mm bright finished floor brass door stopper with rubber cushion, necessary brass screws etc. to suit shutter thickness complete |
| 24 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 25 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including Hot finished welded type tubes |
| 26 | Providing and fixing Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturers) of 1st quality conforming to IS: 13755 of ORIENT, SOMANY, KAJARIA or equivalent make in colour such as White, Ivory, Grey, Fume Red, Brown laid on 20 mm thick bed of Cement Mortar 1: 4 ( 1 cement : 4 coa.rse sand) including pointing the joints with white cement and matching pigment etc., complete. In all colours, shades, except White, Ivory, Fume Red Brown |
| 27 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours shades except burgundy, bottle green, black of any size as approved by Engineerin- Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 28 | Rough cast plaster upto 10m height above ground level with a mixture of sand and gravel or crushed stone from 6mm to 10mm nominal size dashed over and including the fresh plaster in two layers , under layer 12 mm cement plaster in 1:4 ( 1 cement: 4 coarse sand ) and top layer 10 mm cement plaster with cement mortar 1:3 ( 1 cement: 3 fine sand ) mixed with 10% finely grounded hydrated lime by volume of cement. |
| 29 | 12 mm cement plaster of mix :1:4 (1 cement: 4 coarse sand) |
| 30 | 6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand) |
| 31 | Providing and applying white cement based putty of average thickness 1mm of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 32 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade :New work (two or more coats) over and including water thinnable priming coat with cement primer |
| 33 | Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives.New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm. |
| 34 | Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture |
| 35 | Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profilesduly reinforced with 1.60 ± 0.2 m thick galvanized mild steel section made from roll forming process ofrequired length (shape & size according to uPVC profile), uPVC extruded glazing\ beads of appropriatedimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated)casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plasticcaps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cutand fusionwelded at all corners, mullion (if required) shall be also fusion welded\ including drilling of holes for fixinghardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wallshall be filled with weather proof silicon sealant over backer rod of required size and of approved quality,all complete as per approved drawing & direction of Engineer-in-Charge.(Single / double glass panes andsilicon sealant shall be paid separately). Variationin profile dimension in higher side shall be acceptedbut no extra payment on this account shall be made..Casement window double panels with S.S. friction hinges (350 x 19 x 1.9 mm) made of (big series)frame 67 x 60 mm & sash / mullion 67 x 80 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead/ double glazing bead of appropriate dimension. (Area of window above 1.50 sqm). |
| 36 | Providing and fixing double glazed hermetically sealed glazing in aluminum windows, ventilators and partition etc. with 6mm thick clear float glass both side having 12mm air gap including providing EPDM gasket, perforated aluminum spacers, desiccants, silicon sealant (both primary and secondary sealant) etc. as per specifications, drawings and directions of Engineer-in-charge complete |
| 37 | Providing and fixing 50 mm thick extruded polystyrene rigid insulationboard of required size between cavity wall, complying with ISO 4898:2008 & ASTM C 578-08b - type VI, having thermal conductivityof 0.0289 W/m K as per ASTM C 578 (measured as per IS 3346), compressive strength of > 350kPa listed as per ASTM D 1621, density of 34-36 kg/m³ as per ASTM D 1622, water absorptions <1% by volume as per ASTM D 2842, oxygen index of 24.1 to 28.1 listed as per ASTMD 2863, cell size 0.4 mm of dia (max) as per ASTM D 3576. Fire retardant property as per DIN 4102, Part 1 of class B2 and as per ASTM E84 class A, fixed with suitable water based adhesive and fastener, complete in all |
| 38 | Providing and fixing 2nd class teak wood plain lining tongued and grooved, including wooden plugs complete with necessary screws and priming coat on unexposed surface.40 mm thick |
| 39 | Providing and laying gang saw cut 30 mm thick, mirror polished pre moulded and pre polished machine cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring in road side plazas and similar locations, laid over 20mm thick base of cement mortar 1:4 (1 cement : 5 coarse sand) including grouting the joints with white cement mixed with matching pigment, epoxy touch ups etc. complete as per direction of Engineer-in-Charge. With granite stone of colour black, cherry/ruby red of area less than 0.50 sqm. |
| 40 | Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns,raft etc. for mass concrete. |
| 41 | Suspended floors, roofs, landings, balconies and access platform. |
| 42 | Lintels, beams, plinth beams, girders, bressumers and cantilevers. |
| 43 | Columns , Pillars , Piers, Abutments, Posts and Struts. |
| 44 | Stairs , ( excluding landings ) except spiral-staircases. |
| 45 | Providing and fixing of facade at all heights with extruded hollow Clay / Terracottaventilated rainscreen tiles of height 250/ 300/ 400mmand length of 595 mm ofapproved texture,design and pattern having Flexural Strength/ Modulus ofRupture of > 14 N/m2 and maximumwater absorption of 10% tested as per ISO10545-4:2004(E) and ISO 10545-3:1995 respectively in true level fixed to asupportingaluminium framework(Alloy 6063 T5/T6) consisting of vertical 'T' (forintermediates)/ 'L'(for ends/ termination)/ Tubular sections (atcorners)of size80x60x2mm/ 40x60x2mm/ 40x40x2mm respectively, spaced at maximum spacingof 600mm c/c matching to the tilevertical grid, and horizontal aluminium 'C'-clamps of size 56x25x2mm thickness of length 150mm at junction of tiles and oflength 75mmat wall ends/ corners fixed on top of the vertical sections at spacingof 250/ 300/ 400mm c/c matching to the tile horizontal grid with twonumbers ofself-drilling / self-tapping SS screws of size 5.5x25 mm with EPDM washers.The vertical 'T'/'L/ Tubular' sections shall be fixed to the wall using HDG (hot-dipgalvanized)steel L-brackets (galvanizing thickness ofminimum 80 microns)of size110x80x6 mm at intermediate vertical aluminium profiles and of size 220x110x12mm at outer corners andstainless steel grade 304,M10 full threaded anchorfasteners with nylon sleeve 100mm long (for brick work) and M8 expansionanchorfasteners 75mm long for concrete surface, spacing of brackets to be basedon a structural/ static calculation. The brackets shall be oflength 175mm atjunction of two vertical aluminium profiles and of length 100mm at intermediatepoints of vertical profiles and shall befixed to the vertical aluminium T / L /Tubular profiles using two numbers self-drilling/ self-tapping SS screws of size5.5x25mm with EPDM washers.EPDM gaskets to be fixed in between brackets and vertical profiles. The tiles shallbe mounted on the ‘C clamps such that the tiles aresupported at top and bottomat both ends. The tiles shall be additionally secured to the horizontal ‘C clampsusing special SS clips ofrequired size which shall be inserted and pressed intoposition on the ‘C clamps holding the tiles and the cut-tiles shall be glued atpointsto the horizontal ‘C clamps by using MS Polymer sealant adhesive. Thevertical joint open groove between two adjacent tiles shall be5mm. The tiles andsystem shall be designed to resist wind load as per IS 875 (Part 3) according todifferent zones. The tiles shall beinstalled using the ventilated rain screenprinciple with provision for natural ventilation of the space between the facadetiles and thestructural wall. The work shall be carried out as per specification,drawing and as per direction of the Engineer-in-Charge.With 16mm thickness (+/- 10%) terracotta tiles of other than grey colors |
| 46 | Providing and laying 60mm thick factory made cement in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid joints with line sand etc. all complete as per the direction of Engineer-in-charge |
| 47 | Providing and fixing tiled false ceiling of specified materials of size 595x595 mmin true horizontal level, suspended on interlocking metal grid of hot dippedgalvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive)consisting of main \\"T\\" runner with suitably spaced joints to get required lengthand of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at1200 mm center to center and cross \\"T\\" of size 24x25 mm made of 0.30 mm thick(minimum) sheet, 1200 mm long spaced between main \\"T\\" at 600 mm center tocenter to form a grid of 1200x600 mm and secondary cross \\"T\\" of length 600 mmand size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked atmiddle of the 1200x600 mm panel to form grids of 600x600 mm and wall angleof size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the gridincluding, required cutting/making, opening for services like diffusers, grills, lightfittings, fixtures, smoke detectors etc. Main \\"T\\" runners to be suspended fromceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods withgalvanized butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mmcenter to center along main T, bottom exposed width of 24 mm of all Tsectionsshall be pre-painted with polyester paint, all complete for all heights as perspecifications, drawings and as directed by Engineer-in-charge.8 mm thick fully perforated calcium silicate board made with Calcareous &Siliceous materials reinforced with cellulose fiber manufactured throughautoclaving process to give stable crystalline structure with minimumcompressive strength 225 kg/ sq. cm, bending strength 100 kg/sq. cm , of size595x595 mm, having perforation of dia. 10 mm with minimum perforated area18 % with non woven tissue on the back side, having an NRC ( Noise ReductionCoefficient) of 0.85, with 50 mm thick rockwool of48 kg /cum backing. |
| 48 | Providing and fixing on wall face un - plasticized Rigid PVC rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion. (i) Single socketed pipes . 110 mm diametre |
| 49 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansionSingle tee with door 110 mm |
| 50 | Shoe (Plain) 110 mm |
| 51 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm |
| 52 | Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams. |
| 53 | Providing and fixing white vitreous china water closet (Indian type W.C . .pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern including flush pipe with manually controlled device (handle lever)conforming to IS:7231, with all fittings and fixtures, complete including cutting and making good the walls and floors wherever requied:W.C. pan with lSI marked white solid plastic seat and lid. |
| 54 | Providing and fixing white vitreous china water closet squatting pan (Indian typeLong pattern W.C. pan of size 580 mm |
| 55 | Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge. |
| 56 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require :White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps. |
| 57 | Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. |
| 58 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. |
| 59 | Providing and fixing toilet paper holder cp brass |
| 60 | Providing and fixing brass bib cock of approved quality :15 mm nominal bore |
| 61 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15 mm nominal bore |
| 62 | Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineerin- charge. |
| 63 | Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 64 | Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes conforming to IS: 15801, UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fittings. This includes testing of joints complete as per direction of Engineer-incharge. PN-16 pipe , 25mm OD(SDR-7.4) |
| 65 | PN-16 pipe , 32mm OD(SDR-7.4) |
| 66 | PN-16 pipe , 40mm OD(SDR-7.4) |
| 67 | Providing material and labour for fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore |
| 68 | 32 mm nominal bore |
| 69 | 40 mm nominal bore |
| 70 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete 25 mm nominal bore |
| 71 | Providing material and labour for placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank |
| 72 | Providing and fixing insulation work for water tank using K flex,nitrile sheet,polythene, glass wool chicken mesh and cover with aluminium sheet complete job |
| 73 | Providing and fixing insulation work of PPR pipe by way of using K flex,polythene,glass wool,chicken mesh and cover with aluminum sheet on outer pipes complete job complete job. |
| 74 | Providing and fixing heat tape 33 watts of multi layer including wiring over pipe line in spring shape all complete job |
| 75 | Providing and fixing insulation work on PPR pipe by using K flex polythene inner pipe complete job |
| 76 | providing and fixing of 1.5 HP tulo pump of approved make like usha,cromton and manufacture as approved by site eng |
| 77 | Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes fittings type B for sewerage waste discharge system (IS:13592 : 1992 Marked) of approved quality /make supreme, jain pipes, sudhakar, prince or equivalent 100 mm dia |
| 78 | 75mm diameter : |
| 79 | Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes fittings type B for sewarage waste discharge system (IS:13592 : 1992 Marked) of approved quality /make Bend of required degree with access door, 100 mm dia |
| 80 | 75 mm dia |
| 81 | Plain bend of required degree. 100 mm dia |
| 82 | 75mm dia |
| 83 | Heel rest sanitary bend 100 mm dia |
| 84 | 75 mm dia |
| 85 | Single equal plain junction of required degree : 75x75x75 mm |
| 86 | Providing and fixing square-mouth S.W. gully trap grade ‘A” complete with C.I.grating brick masonry chamber with water tight C.I. cover with frame of 300 x300mm size (inside) the weight of cover to be not less than 4.50 kg and frame to benot less than 2.70 kg as per standard design :180x150 mm size P typeWith common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 87 | Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size),inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 88 | Providing material and labour for laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150mm dia R.C.C pipe |
| 89 | 250mm dia R.C.C pipe |
| 90 | Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished with a floating coat of For pipes 250 to 300 mm diameter |
| 91 | Constructing brick masonry road gully chamber 50x45x60 cm with bricks of classdesignation 75 in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450mm precast R.C.C. horizontal grating with frame complete as per standard design: With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 92 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required. |
| 93 | Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. |
| 94 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 x 1.5 Sq.mm + 1 x 1.5 Sq.mm earth wire |
| 95 | 2 x 2.5 Sq.mm + 1 x 2.5 Sq.mm earth wire |
| 96 | 2x 10 Sq.mm + 1 x 6 Sq.mm earth wire |
| 97 | 4x 16 Sq.mm + 2 x 6 Sq.mm earth wire |
| 98 | Supplying and fixing following modular type switch/socket on the existing switch box cover including connections etc. as required.5/6 A switch |
| 99 | 3 pin 5/6 A socket outlet |
| 100 | 15/16 A switch |
| 101 | 6 Pin 15/16 A socket outlet |
| 102 | Bell Push |
| 103 | Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. |
| 104 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 2No's 3 pin 5/6 amps modular socket outlet and 2No's 5/6 amps modular switch, connection etc. as required |
| 105 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin 5/6 amps & 15/16 amps. modular socket outlet and 15/16 amps modular switch connection etc. as required. |
| 106 | Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 8 way (4+24) Double Door |
| 107 | 6 way (4+18) Double Door |
| 108 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole 6/16 amp. |
| 109 | Single pole and neutral 40 amp. |
| 110 | Supply and fixing of following sizes of PVC conduit alongwith accessories in surface/recessed including cutting the wall and making good the same in case of recessed conduit as required.(for telephone, TV, Internet) 25 mm |
| 111 | Supply, installation, testing & commissioning of GI Electrode Earthing with 84mm dia and 3 meter length, with 40mm x 6mm thick the electrode should be hot-dip galvinised. The GI Electrode shall be pre-filled with Cristaline Conductive Materila (CCM). The GI electrode shall be surrounded with BEE MOIST compound to provide maximum contact betwen the electrode and compound should be eco-friendly GI Electrode Earthing should be maintinance free and does not require regular manual addition of water . The earthing pit should be covered with PVC cover. |
| 112 | Supplying and laying 25mm x 5mm G.I strip at 0.50 metre below ground as strip earth electrode including connection/terminating with G.I nut, bolt, spring, washer etc. as required. ( Jointing shall be done by overlapping and with 2 sets of G.I nut bolt & spring washer spaced at 50mm). |
| 113 | Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required. |
| 114 | Fabrication, supplying , installation testing and commissioning of following pannel made out of 2mm thick M.S sheet, floor mounted, vermin and dust proof , outdoor type with suitable size of angle iron legs for grounting in the ground, with lockable type hinged doors, duly painted with provision for fixing of 1 no incomer MCCB, MCCB type change over switch 1 no. including supply and fixing 2 sets of Aluminium Bus Bar , and strips for housing MCB's 12 Nos ,MF Digital Meter and other allied accessories etc.as required ( Make as per annexure) |
| 115 | Supplying and fixing MCCB in cubical panel board and breaking capacity MCCB FP in existing cubical panel board including drilling of holes in cubical panel and making connection etc. As required (Make as per annexure enclosed)MCCB FP 200 Amp 30 KA |
| 116 | Change over Switch (on Load ) FP 200 Amp |
| 117 | Supplying and fixing of following rating 240/415 Volt's \\"C\\" Series miniature circuit breaker suitable for lighting and other loads of following poles in the existing MCB DB complete with connections, testing and commissioning (Above to 32 Amp.). TPN 63 Amp. |
| 118 | Supplying and fixing of 1.1 KV PVC insulated and PVC sheathed XLPE Aluminium Power Cable of following sizes on surface/surface cable tray,0.50 mtr bleow ground level etc. as required including carriage upto site of work. (Make as per annexure enclosed) 50 sqmm 3.5 core-Armoured |
| 119 | Supplying and fixing of 200 watt LED Street Light complete with GI pipe bracket duly embeded along the parapet /wall. Wipro LR02 -132-XXX-57-G2or equivalent approved make Supplying & fixing following luminaries as required |
| 120 | Supplying & fixing following luminaries as required 10 watt LED tube light fitting. LL20-111-XXX-65NE3 wipro or equivalent. |
| 121 | 20 watt LED tube light fitting. LL20-221-XXX-65NE3 wipro or equivalent. |
| 122 | Supplying and fixing of following electrical items suitable for operating on 240/230Volts AC, 50 Hz supply. including connections etc. as required. Exhaust fan 225 mm PVC shutter type |
| 123 | 40w 2x2 led pannel ,2' x2' backlit panel cool/warm light 6500k /recessed panel for false ceiling of standard manufacturing with minimum 2years guarantee as per eng i/c supply and fixing of led type downlight |
| 124 | Carriage of material by mechanical transport Cement / Steel …................ 10.0 km |
| 125 | Sand …........................ 15.0 km |
| 126 | Stone aggregate ….................... 20 kms Please Enable Macros to View BoQ information |
