|
| 1 | DSR Item No.1.17 Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. |
| 2 | 3 x 1.5 sq. mm |
| 3 | DSR ITEM No.2.4Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer) as required. (Note: Vertical type MCB TPDB is normally used where 3 phase outlets are required. |
| 4 | 4 way (4 + 12), Double door |
| 5 | DSR ITEM NO.2.10Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 6 | Single pole |
| 7 | Triple pole and neutral |
| 8 | DSR item no. 5.1Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (but without charcoal/ coke and salt) as required. |
| 9 | DSR item no. 5.7Supplying and laying SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required. |
| 10 | DSR 8.12 LED Street light fixture, powder coated pressure die cast aluminium body (System lumen efficacy ≥105 <120 lm/Watt)Supplying, installation, Testing & Commissioning of Street light LED fixture powder coated pressure die cast aluminium body with driver as per the requirement with Driver efficiency >85%, Input voltage: 140-270 Volt AC, frequency 50/60 hz, Operating temp range -5 0C to 50 0C, internal surge protection of 5 KV L,N,E as per IEC 61000-4-5, Driver efficiency >85%,THD < 10% as per IEC 61000-3-2, P. F.≥0.95, IP-66,IK-10, CRI >70, under voltage and over voltage protection, EMIEMC As per CISPR -15, lenses for beam angle as per IESNA type I/II/III as per the width of the road and the project requirement., suitable to fit in up to 65mm dia pipe, life time (LED, Driver & electrical circuitry) of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin),SDCM (Standard Deviation Colour Matching) <5, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard complete in all respect i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥105 <120 lm/Watt output .LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C). |
| 11 | 45watt |
| 12 | DSR item no. 8.15LED Flood Light, powder coated pressure die cast aluminium (System lumen efficacy ≥105 <120 lm/Watt).Supplying, installation, Testing & Commissioning of FloodLight, powder coated pressure die cast aluminium body withbuilt in or separate driver as per the requirement with Driverefficiency >85%, Input voltage: Input voltage: 140-270 VoltAC, freq 50/60 hz, Operating temp range -5 deg to 50 degcentigrade, internal surge protection of 5 KV L,N,E as perIEC61000-4-5, Driver efficiency >85%,THD < 10% as per IEC61000-3-2 , P. F.≥0.95, IP-66,IK-10, CRI >70, under voltageand over voltage protection,EMI-EMC as per CISPR -15,lenses for beam angle 30 deg-120deg as per the application andthe project requirementdeg., suitable tilt able fitting, life time(LED,Driver & electrical circuitary) of minimum 50000 BurningHours with 70% of initial Lumen maintained till life ends asper LM80 extrapolation IES TM-21-11 report, CCT 3000°K /4000°K / 5700°K /6500°K (As per ANSI Bin) ,SDCM(Standard Deviation Color Matching) <5, Maximumpower consumption should not more than the specified ratingand Fixture shall be of relevant BIS standard complete in allrespect i/c external connections with 1.5 sq mmFRLS/HFFR, PVC insulated copper conductor single corecable and earthing etc. as required with Minimum 5 year OEMwarranty. System lumen efficacy 105 <120 lm/Watt output.LM79 & LM80 Test report and all testing required for LEDfixtures as per BIS shall be submitted. Shape size and CCTshall be as approved by Engineer-in-Charge as per requirement.(Thermal management: heat sink of aluminium housing suchthat LED junction temperature shall not rise above 90°C). |
| 13 | 70watt |
| 14 | DSR Item No.15.16 Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. |
| 15 | 63 mm dia (OD-63 mm & ID-51 mm nominal) |
| 16 | Supply and erection of Sheet steel TPN MCB enclosure for MCB TPN 63 Amp. The job includes cost of labour, making connection and other petty material required to complete the job to the entire satisfaction of Engineer in charge of the work. |
| 17 | S/E of M.S. bracket (‘L’ shape) made from 40mmx40mmx 5mm thick angle iron to be installed on existing parapet / wall with the help of suitable size of nuts & bolts etc. for erection of metal halide flood light fitting. The job includes cost of painting of bracket with superior quality of paint and other all petty material etc. as required to complete the job. |
| 18 | Supply and erection of sheet metal cubical pedestal of suitable dimensions made from 50 mm X 50 mm X 6 mm thick M.S angle iron frame, covered with 1.6 mm thick M.S. sheet duly welded on five sides and front side hinged complete with locking arrangement with 4 Nos. switchgear supporting members each of M.S. flat 50 mm X 6 mm thick of suitable length duly welded. The cubical pedestal shall have 4 Nos. legs of 50 mm X 50 mm X 6 mm each 60 cm long M.S. angle iron each long including painting, bonding to the existing earth etc. the same shall be erected in the 1:2:4 cement concrete plat-form of suitable dimensions 15cm high form ground level and 45 mm thick. The cubical pedestal shall be 15 cm from the top of cement concrete platform. |
| 19 | Cubical size 900 mm x 600 mm x 300 mm |
| 20 | Supply and Laying of following XLPE insulated and PVC sheathed, armored, aluminum conductor cable of 1.1KV grade as per IS 7098 (Part-I) 1988 (amended up to date) of the following sizes to be laid in existing trench/ DWC/RCC/HUME pipe as required at site. The job include the cost of making connections with suitable size of Al. Lugs/ thimbles, testing, commissioning etc. as required to the entire satisfaction of Engineer In Charge. |
| 21 | 10 Sq.mm 4 Core PVC Ar. Aluminum Conductor Cable |
| 22 | 16 Sq.mm 4 Core PVC Ar. Aluminum Conductor Cable |
| 23 | Supply and laying of PVC insulated aluminum conductor unarmored cable 10 mm² 2 core flat with 6 SWG GI Earth wire on existing surface with suitable clamps/ Hangers etc. The job including making connection and petty material such as labour etc. as required to complete the job as per satisfaction Engineer in charge.The cable should be of Grandlay/Havells/RR cable/ KEI/ Polycab make only. |
| 24 | Labour charges for horizontal boring 1Mtr. Below ground level including cost of 2 nos. pit digging and refilling complete in all respects up to entire satisfaction of the EIC of the work. |
| 25 | S/E of 5 mtr. long G.I. Pipe pole made out of 2.5” dia G.I. Pipe pole (5 mtr.) of B-Class ISI marked G.I. Pipe. The pole shall be erected 1mtr. below ground level in 6” internal dia readymade RCC muff. The gap between the pole and the muff shall be filled with cement concrete 1:2:4. The job includes the cost of fabrication, Welding, Grinding, making hole for entry of wire, labour, all petty material, carriage etc. required to complete the job to the entire satisfaction of the E.I.C. The cost includes all labour and material including fabrication charges of Pole & carriage to the site of work. The G.I. pipe should B-Class ISI marked Jindal / Hindustan make only. |
| 26 | Supply and Erection of Cement Collar and Jn. Box at the base of the pole with the detailed specification as given below.: |
| 27 | Jn. Box Construction: |
| 28 | Supply and fixing of OEM made Junction box IP 66/67 made out of Polycarbonate with Glass fiber reinforced of size 205 x 255 x 112 (mm) (minimum) with 5 nos. OEM made connectors/terminal blocks. The Jn. Box and connectors/terminal blocks should be supplies by OEM. The terminal blocks/connectors should be of Hensel/Wago/Elmax/Siemens make only and Junction box shall be of Hensel make KF-2525 G or its equivalent Clipsal/Legrand/Schneider/ABB make only. The junction box shall be fire retardant and self-extinguishing. The gasket materal shall be polyurethane and the gasket shall be internally embedded. The job includes all labour and petty material required to complete the job to the entire satisfaction of the Engineer in charge of work. |
| 29 | Cement Collar: |
| 30 | The box shall be enclosed in a cement collar made from cement concrete 1:2:4 and outside dia. 16”/18”. |
| 31 | The collar shall be embedded in the ground upto 6” shall stand 9” above ground shall have 12” high MS box and 6” top over the box. |
| 32 | The collar shall be provided with medium class 2 Nos. PVC pipes of 50 mm dia& 45 cm long to facilitate the entry of cables in the Jn. Box. |
| 33 | The collar shall be plastered, properly finished and painted with 2 coats of snowcem of superior quality to complete the job including new thimbles & making connections. |
| 34 | The job includes all labour to break the old existing collar & junction box including disposal of waste material from site and petty material required to complete the job to the entire satisfaction of the E.I.C. of the work.The dismantled junction box shall be made from the firms. |
| 35 | Dismantling of existing damaged cement collar from the steel tabular pole. The job include cost of dismantling of incoming and outgoing connection from the junction box. The job also include throwing of malba into dumping ground, cost of all labour and other petty material required to complete the job to the entire satisfaction engineer in charge of the work. |
| 36 | Supply and Erection of 40-45 watt LED Post Top Lantern fittings made of cast alum. Housing with power to be mounted on directly on inbuilt Heat sinks. A UV stabilized PC/PMMA diffuser is provided for Glare Free Lighting with high visual comfort to complete with Electronic LED Driver Power supply & related accessories with the following specifications to be installed on existing pole. The make & model of the fitting should be of Bajaj BGCPNP 45 W/ WIPRO LP06351 XXX-57XX36W/ Twinkle LuxMax-PT-151-L 40 W LED/Surya Rigel (SLE PT 40W)/Mayfair MF PTL LED 651 45 W/Panasonic PPTM02408 or its equivalent to Philips/ Lauritz Knudsen/ Havells/Crompton Make only Specifications of LED fittings: K-Lite Juno(Cat no.5380) 36 watt LED as per complete item no.18 of DNIT. |
| 37 | Supply and erection of three phase Terminal connector with neutral strip for existing Street light pole. The job includes cost of making incoming and outgoing connection etc. after dismantling the existing connection with 6 Nos thimble and 6 No washer etc. The job includes cost of labour and other petty material required to complete the job to the entire satisfaction of Engineer-in-charge. Please Enable Macros to View BoQ information |
