Tender For Development Of New A Site Regular Retail Outlet At Location-On Sh-8 From Bankura More To Khejurhati Bus Stand, Dist-Purba Bardhaman Under Durgapur Divisional Office Of West Bengal State Office, Purba Bardhaman-West Bengal

TDR : 54401193

Tender Notice
BOQ

6 Days Left

Purba Bardhaman , West Bengal

Tender Brief : Tender For Development Of New A Site Regular Retail Outlet At Location-On Sh-8 From Bankura More To Khejurhati Bus Stand, Dist-Purba Bardhaman Under Durgapur Divisional Office Of West Bengal State Office

Document Fees
Refer document

EMD
Refer document

Tender Value
₹ 1.23 Crore /-

Submission Date
12-03-2026

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	DEVELOPMENT OF NRO Khejurhati P&M
2	Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30 cm in depth, 1.5m in widt h as well as 10 sqm on plan) including taking out and disposal of excavated earth within or outside site to unobjectionable place a nd lift upto 1.5m, as directed by Engineer-in-charge. Disposed earth to be levelled and neatly dressed. Extra for levelling & neatly dressing of disposed soil completely to be paid separately as per item no. MPLCN00600
3	EXC. OVER AREAS IN ALL KINDS OF SOIL
4	EXC. OVER AREAS IN ORDINARY ROCK
5	Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1. 5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excav ated soil & disposal of surplus excavated soil as directed, within or outside the site at an unobjectionable place.
6	EXC. IN ALL KINDS OF SOIL
7	EXC. IN ORDINARY ROCK
8	EXC.EXTRA LIFT EVERY 1.5M ALL KIND SOIL
9	EXC. - EXTRA LIFT EVERY 1.5M HARD ROCK
10	FILLING AVAILABLE EARTH
11	SUPPLY AND FILLING IMPORTED EARTH
12	Supplying and filling in plinth with sand within specified grading zone of fine aggregates specified in table 3.1, clause 3.1.3 of a ttached specifications under floors, etc. in layers not exceeding 20cm in depth, each deposited layer to be compacted by ramming inc luding watering, consolidating and dressing complete.
13	SUPPLY FILLING LOCAL SAND ZONE IV
14	1 CEMENT:2 COARSE SAND:4 AGG. 20MM
15	1 CEMENT:3 COARSE SAND:6 AGG. 20MM
16	Centering and shuttering including strutting, propping etc. and removal of form work for:
17	CENT.& SHUT.FOR PCC-FOUND,FOOTING ETC
18	Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level
19	RCC 1:1½:3 UP TO PLINTH LEVEL W/O C&S
20	Centering and shuttering including strutting, propping etc. and removal of form for :
21	CENT.& SHUTT. FOR RCC FOUNDN,FOOTING
22	CENT.& SHUTT. FOR RCC COLUMNS
23	Supply of Steel reinforcement for R.C.C. including straightening, cutting, bending, placing in position and binding all complete at all levels
24	TMT BARS FE- 500 GRADE
25	Providing and laying Brick work with common burnt clay F.P.S (non Modular) bricks of class designation 7.5 in foundation & plinth
26	BRICK WORK IN CM 1:6 IN FOUNDN & PLINTH
27	Providing and fixing 18mm thick gang saw cut mirror polished premoulded and prepolished, machine cut for kitchen platforms, vanity counters, sills, facias, Pump Island & similar locations of required size, approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding & polishing to edge to give high gloss finish etc. complete at all levels.
28	POLISHED GRANITE - KITCH.CUNTR<0.50SM
29	POLISHED GRANITE - KITCH.CUNTR>0.50SM
30	Extra for providing edge moulding to 18mm Granite/ marble stone counters,Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in- Charge.
31	EXTRA FOR EDGE MOULDING TO GRANITE WORK
32	EXTRA FOR OPENING FOR WASH BASIN ETC.
33	STRUCTURAL STEEL WORK IN SINGLE SECTION
34	STR.STEEL IN BUILT UP SECTION
35	Steel work in built up tubular (round,square or rectangular hollow tubes etc) trusses etc. including cutting,hoisting fixing in posi tion and applying a priming coat of approved steel primer, including welded and bolted with special shaped washers etc. complete.
36	HOT FINISHED WELDED TYPE TUBULAR TRUSS
37	Providing and laying cement plaster on surfaces with fine sand including curing etc.
38	12MM CEMENT PLASTER,1:4 WITH FINE SAND
39	ACRYLIC SMOOTH EXTERIOR PAINT
40	DELUXE MULTISURFACE PAINT-STEEL SURFACE
41	Providing and fixing B class G.I. pipes complete with G.I. fittings including trenching and refilling etc for WATER and AIR, Externa l work
42	15 MM DIA. NOMINAL BORE
43	Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :
44	15MM BRASS BALL VALVES-PLASTIC FLOAT
45	S/L OF 50 MM DIA SINGLE WALL FLEXIBLE PI
46	S/L OF 80 MM DIA SINGLE WALL FLEXIBLE PI
47	Supplying and fixing MS foundation bolts with necessary GI nuts and washers of specified sizes,all conforming to relevant Indian Sta ndards and as approved by Engineer-in-charge :
48	FOUND.BOLT 16MMDIAX400MM L,75X5MM PLATE
49	FOUND.BOLT 25MMDIAX1.0M L,100X8MM PLATE
50	Installation of supplied 20 KL Tank as per specified drawings as per work description but excluding all works of kerb wall and Gaske t for manhole including painting / doping with Shalimastic HD as applicable as per specifications complete. RCC works wherever menti oned shall be of grade M20
51	20KL TANK IN EARTHPIT WITH RCC STRIPRAFT
52	S/L U/G MS THREADED 40 MM DIA PIPE
53	S/L A/G MS THREADED 40 MM DIA PIPE
54	S/L U/G MS WELDED 80 MM DIA PIPE
55	S/L U/G MS WELDED 50 MM DIA PIPE
56	Supply & welding slip-on flanges conforming to IS2062 GrA, ANSI B16.5, Class#150 with 3 runs of weld outside and one run of weld ins ide the flanges as per specifications and standard Drg.enclosed herein
57	S/W SLIPON FLANGES OF 80 MM DIA.
58	S/W SLIPON FLANGES OF 50 MM DIA.
59	Making flanged joints between flanges slip on, blind and flange etc. including providing/supplying 3 mm thick permanite oil gasket, nuts, bolts, bonding with 3 mm dia copper wire etc.complete as per IOCL specifications.
60	MAKING SLIPON / BLIND FLANGE JOINT 80MM
61	MAKING SLIPON / BLIND FLANGE JOINT 50MM
62	Supplying and installation of the following threaded
63	80 MM DIA AL. CAMLOCK COUPLING - MALE
64	Supply and installation of ‘U’ type CS bend on the vent pipes including painting as per specifications and supplying and brazing wi re mesh of 11 mesh per linear centi-meter of non-corrosive metal in two layers on both ends.
65	S/I U TYPE 40MM CS BEND ON VENT PIPES
66	Supply and installation of screwed type gun metal valves as per IOC specifications: Ball Valve
67	S/I SCREWED GM BALL VALVE 50MM DIA
68	INSTALLATION OF SD/HD DISPENSING PUMPS (MONO /DUAL) Installation of supplied standard duty/heavy duty dispensing pump on existing pu mp island as per IOCL's drawings and instructions including supplying /filling required quantity of dry sand in the pit(s) below th e pump
69	INST.OF DU WITH ANCHOR BOLT & CC FOUND.
70	Installation of supplied Multi Product Pumps / Dispensers on pump island as per manufacturers installation manual, drawings, includi ng supplying, providing necessary frame of ISMC 100, foundation bolts, supplying and filling required quantity of dry sand in pit(s) below the pump
71	2 PRODUCT - 4 NOZZLE MPP/MPD
72	Air compressor Supply and installation of horizontal air compressor assembly with delivery pressure of 12 kg/sq cm equipped with pre ssure gauge, non- return/safety/drain/delivery valves, automatic cut-off switch and suitable electrical connections & all standard a ccessories, including civil works:
73	S/I OF 5 HP (160-220 LITRES) COMPRESSOR
74	S/I DIGITAL TYRE INFLATOR
75	Transportation of equipment from one location to another location including enroute all taxes, levies and unloading/loading by a s uitable vehicle exclusively for this purpose (In case of tank same shall be loaded by the tank fabrication contractor)
76	TRANSPTN OF 15/20 KL TANK : 0 - 30 KM
77	TPT/KM OF 15/20KL TANK: EXTRA > 30KM
78	T-MONO/DUO/AIRCOMP/STP/PUMPS:3-6, <30KM
79	T/KM-MONO/DUO/AIRCOMP/STP/PUMPS:3-6, >30
80	TPT - MPD/MPP:1-2, <30KM
81	TPT/KM - MPD/MPP:1-2, >30KM
82	S & F FRESH WATER IN U/G TANK
83	REMOVING WATER FROM U/G TANK
84	Re-installing the dispensing pump on existing foundation including connecting pipelines, electrical connections, tightening nuts of the foundation bolts etc. complete.
85	RE-INSTALLING MPD / MPP UNIT
86	S/F 2\\" PV VALVES
87	ALTERATION TO MANHOLE COVER FOR STP
88	INSTALLATION OF STP
89	CABLING AND ALLIED WORKS - ARMOURED CABLES Supply & laying of XLPE insulated PVC sheathed aluminium/copper conductor, 1.1 kV grade armoured cable conforming to IS:7098, as per approved make in ground/ trench/surface/pipe, etc. whereever required as per direction of Engineer In-charge. Note: The rate of Installation should be inclusive of Cable clamps, tags Saddles, Consumables etc. Trays/pipe s, trenches, fabricated tray supports etc will be covered & paid in Separate Items
90	S&L 3X2.5 SQMM,1.1KV FRLS CU ARMD CABLE
91	S&L 4X2.5 SQMM,1.1KV FRLS CU ARMD CABLE
92	SUPPLY AND LAYING OF FLAT CABLES
93	S&L 3X4SQMM CU FLAT CABLE -SUBM PUMP
94	CABLE TERMINATION GLANDS NON-FLP HEAVY DUTY DOUBLE COMPRESSION Cable Termination (NON FLP): Providing termination of 1.1 kV grade ar moured cable for the following sizes including supply of NON FLP heavy duty Double Compresson cable glands, crimping type lugs and allied jointing materials, etc. all complete as per specification and direction of Engineer In-charge. Glands and lugs shall be of approved make. Copper lugs for copper cables and aluminium lugs for aluminium cables shall be used.
95	CABLE TERM,NON FLP DC GLAND 3X2.5SQMM
96	CABLE TERM,NON FLP DC GLAND 4X2.5SQMM
97	CABLE JOINTING Cable Jointing : Providing straight through joint of following 1.1 KV grade XLPE insulated armoured cable with M-Seal make jointing kit, and other jointing material, etc. all complete including supply of all materials as per specification & directio n of Engineer In-charge.
98	CABLE JOINTING KIT FOR 3X2.5SQMM
99	CABLE JOINTING KIT FOR 4X2.5SQMM
100	CABLE ROUTE MARKER WITH 100X100X5MM
101	S&F OF FLP JUNC. BOX (4 WAY ENTRY)
102	Supply & drawing/laying, jointing, connecting, testing and commissioning of earth strip/copper strip/GI wire for earthing and light ning protection under or aboveground complete as per specification for the following :
103	EARTHING WITH 50 X 10MM G.I. STRIP
104	EARTHING WITH 32 X 6 MM G.I.STRIP
105	EARTHING WITH 50 X 6 MM G.I. STRIP
106	EARTHING WITH 25 X 3 MM GI STRIP
107	16SQMM CUCABLE INCL.CROCDILCLIPIN LT PNL
108	Supply of chemical earthing technology (pipe in pipe) for Electrode Design of specified Current Carrying Capacity in kA for 1 second . Crystaline Conductive mixture which is machine pressed in the pipes should not disintegrade or collapse when the outer pipe corrod es. Resistivity of the Material shall be less than 0.2ohm meter when tested by making a 20cm Cube of the Material & checking the res istance across the opposite faces of the cube. Necessary Test certificate shall be submitted. Concentric Earth Electrode Pipe should be MS of IS:1239 quality & hot Dip galvanised of 150 micron. Electrode Material Selection should be as per Clause 9.3: IS-3043.
109	CHEM EARTHING - PIPE IN PIPE 15KA
110	Supplying & Fixing of following items for electrical safety in switch rooms/DG rooms etc
111	S&F RUBBER MAT 33KV GRADE (2MX1M SIZE)
112	S&F 6MM THICK CHEQUERED PLATE
113	S&F SHOCK TREATMENT CHART
114	S&F 11 KV GRADE HAND GLOVES, ISI MARK
115	PANEL BOARDS AND DISTRIBUTION BOARDS Supply, installation, testing and commissioning of cubicle type power and motor control centre panel fabricated out of 14 SWG sheet steel undergone 7 tank process,dust & vermin proof, floor mounting type, suitable for indoor us e having cable entry from the bottom and having following specific components complete, control wiring etc. as per enclosed standard drawing. Any other components/hardware required to complete the panels but not mentioned here shall also be provided. Note: Both in comers should have mechanical interlock for proper & safe operation. The MCCB used for incomer feeder shall have short circuit, over load and earthfault protection and also shunt coil for ESD operation. The Bus Bar support shall be DMC/ SMC/Epoxy moulded. All equip ment/components shall be mounted logically to have free access for maintenance, tightening of connections & visual inspection. All t he metering equipment shall be Digital & mounted on the panel and size of meter shall be 96 mm x 96 mm. The Bus Bar shall be provide d with heat shrunk PVC sleeves & all power terminals shall be stud type with properly shrouding to avoid accidental contact. Neopren e type gasket shall be provided at the doorof the panel. The enclosure of the Panel shall have IP52 degree of protection. 2 Nos eart h terminal shall be provided at the Panel frame with extension link for earthing connections. Painting:The under surface shall be pr epared by applying a coat of phosphate paint and coat of yellow zinc chromate primer. The under surface shall be made free from all imperfections before undertaking the finishing coat. After preparation of the under surface, the switchboard shall be spray painted with two coats of epoxy based final paint or shall be powder coated. Colour shade of final paint shall be RAL 7032.
116	PANEL & DISTRIB. BOARDS - MEDIUM RO
117	Supplying and fixing of following MCBs with necessery inter connections on existing DB, Panel board etc.
118	S&F MCB+ELCB UPTO 32A DP MCB
119	Supply and installation of MCB distribution board having Double door complete with tinned cu bus bar, neutral bus bar, earth bar, din bar, interconnection, earthing etc. without incoming isolator and MCBs
120	S&F MCB DB WITH 4 WAY (4+12) TPN
121	S & I OF FLP ESD PUSH BUTTON
122	Supplying and fixing 12 volt Charged LA battery of approved make for Electronic dispensing pumps including giving necessery electric al connection for the following AH ratings.
123	12V , 7AH CHARGED LA BATTERY WITH STAND
124	CONSTANT VOLTAGE TRANSFORMER Supplying, installation, testing and commissioning of single phase, air cooled constant voltage transfo rmer of approved make having input voltage range of 180-260V and output voltage of 220/230V with sine wave output wave form and havi ng automatic current limiting and short circuit protection including all accessories complete (for displays) for the following VA r atings.
125	S/I SINGLE PAHSE AIRCOOLED 500VA CVT
126	SINGLE SERVO VOLTAGE STABILISER Supply and fixing of 230V, Single phase, AC Servo voltage stabilizer of approved makes,(Range - 180 - 250 minimum) shall be provided for Individual dispensing pump as per IE Regulation and as per specification
127	S/I SINGLE PHASE SERVO STABILISER-5 KVA
128	THREE PHASE SERVO STABILIZER Supplying and fixing of 3 phase air cooled servo stabilizer for balanced and unbalanced load shall be i ndependent correction of each phase (Range 300 - 460 V minimum) and as per specification
129	3PHASE,30 KVA AIRCOOLED SERVO STABILISER
130	Supply, fitting, fixing of arm bracket, tubular type, 38mm/50mm dia on pole including painting, all complete.
131	S&E ARM \\" Y BRACKET 38/50MM DIA. ON POLE
132	Supplying & drawing inside the poles 3 core 2.5 sq.mm PVC insulated flexible copper conductor, fixing of junction box at the pole ba se (excluding supply of JB), making all connections on both ends, all complete as per specification and direction of Engineer In-cha rge.
133	S&D 3CX2.5SQMM PVC CU WIRE IN L POLE
134	OCTAGONAL POLES Supply & Fixing of Octagonal Poles of following type (Civil job shall be paid separatly) :
135	S&E 7M HIGH GALVANISED OCTAGONAL POLE
136	YARD LIGHTS: 100W WITH IP66 PROTECTION
137	PANEL BOARD STICKERING WORK
138	PANEL BOARD MARKING
139	PREPARATION OF SLD - ELECTRICAL LAYOUT
140	PREPARATION OF SLD - EARTHING LAYOUT
141	Supply and Installation of 16 SWG MS/GI powder coated weather proof Earthing Box of following size with door and locking arrangement with lock and key. Box to be mounted on ISA 40x40x5 (Painted with black synthetic enamel paint) frame having 2 legs of length 800 m m (500 mm above ground and 300 mm below ground which is to be grouted with PCC 1:2:4). Bottom of box should have opening for incomin g earth GI strips all complete, as per specification and direction of Engineer-in-charge. Note: EARTHING BOX in RED should be boldly written over the box. The box should have a hood at the top extending outwards such that no water should seep through inside the bo x during rainy season to avoid rusting.
142	i) 450 X 300 X 250 mm
143	DEVELOPMENT OF NRO Khejurhati Non-P&M
144	SURFACE EXCAVATION
145	Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30 cm in depth, 1.5m in widt h as well as 10 sqm on plan) including taking out and disposal of excavated earth within or outside site to unobjectionable place a nd lift upto 1.5m, as directed by Engineer-in-charge. Disposed earth to be levelled and neatly dressed. Extra for levelling & neatly dressing of disposed soil completely to be paid separately as per item no. MPLCN00600
146	EXC. OVER AREAS IN ALL KINDS OF SOIL
147	EXC. OVER AREAS IN ORDINARY ROCK
148	Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1. 5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excav ated soil & disposal of surplus excavated soil as directed, within or outside the site at an unobjectionable place.
149	EXC. IN ALL KINDS OF SOIL
150	EXC. IN ORDINARY ROCK
151	EXC.EXTRA LIFT EVERY 1.5M ALL KIND SOIL
152	EXC. - EXTRA LIFT EVERY 1.5M HARD ROCK
153	FILLING AVAILABLE EARTH
154	SUPPLY AND FILLING IMPORTED EARTH
155	Supplying and filling in plinth with sand within specified grading zone of fine aggregates specified in table 3.1, clause 3.1.3 of a ttached specifications under floors, etc. in layers not exceeding 20cm in depth, each deposited layer to be compacted by ramming inc luding watering, consolidating and dressing complete.
156	SUPPLY FILLING LOCAL SAND ZONE IV
157	Providing and laying in position cement concrete of specified grade excluding cost of centering & shuttering. All work up to plinth level:
158	1 CEMENT:2 COARSE SAND:4 AGG. 20MM
159	1 CEMENT:3 COARSE SAND:6 AGG. 20MM
160	1 CEMENT:4 COARSE SAND:8 AGG. 40MM
161	Centering and shuttering including strutting, propping etc. and removal of form work for:
162	CENT.& SHUT.FOR PCC-FOUND,FOOTING ETC
163	PRE-CAST CC 1:2:4 KERB STONE,..WITH C&S
164	40MM DAMP PROOF COURSE
165	Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level
166	RCC 1:1½:3 UP TO PLINTH LEVEL W/O C&S
167	Providing & Laying Reinforced cement concrete work in walls (Any thickness) including attached pilasters, buttresses, plinth an d string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level UP TO FLOOR V LEVEL excludin g cost of centering, shuttering, finishing and reinforcement :
168	RCC 1:1½:3 WALLS ..UPTO 5 LVL W/O C&S
169	Centering and shuttering including strutting, propping etc. and removal of form for :
170	CENT.& SHUTT. FOR RCC FOUNDN,FOOTING
171	CENT.& SHUTT. FOR RCC WALLS ETC.
172	CENT.& SHUTT. FOR RCC SLABS, ROOFS
173	CENT.& SHUTT. FOR RCCLINTELS, BEAMS
174	CENT.& SHUTT. FOR RCC COLUMNS
175	CENT.& SHUTT. FOR RCC FINS
176	CENT.& SHUTT. WITH PLY FOR RCC BEAMS
177	Supply of Steel reinforcement for R.C.C. including straightening, cutting, bending, placing in position and binding all complete at all levels
178	TMT BARS FE- 500 GRADE
179	Providing and laying in position ready mixed M-25 grade concrete for reinforced cement concrete work using cement content as per ap proved design mix manufactured in fully automatic batching plant & transported to site of work in transit mixer for all leads havin g continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying, excluding the cost of centering, shuttering, finishing & reinforcement including co st of admixtures in recommended proportions as per IS:9109 to accelerate/ retard setting of concrete, improve workability without im pairing strength & durability as per direction of Engineer-in-charge (Note :- Cement content considered in this item is @ 330 kg/cum . Less cement used as per design mix (if any) will be recoverable separately. No extra payment against extra cement if used shall be payable.
180	M25 GRADE RMC UPTO PLINTH LEVEL
181	Providing and laying Brick work with common burnt clay F.P.S (non Modular) bricks of class designation 7.5 in foundation & plinth
182	BRICK WORK IN CM 1:6 IN FOUNDN & PLINTH
183	BRICKWORK IN CM 1:6 IN S/STR UPTO LVL V
184	HALFBRICK MAS IN CM1:4 S/STR UPTO LVL V
185	DRY BRICK ON EDGE FLOOR IN MUD MORTAR
186	Providing and fixing 18mm thick gang saw cut mirror polished premoulded and prepolished, machine cut for kitchen platforms, vanity counters, sills, facias, Pump Island & similar locations of required size, approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding & polishing to edge to give high gloss finish etc. complete at all levels.
187	POLISHED GRANITE - KITCH.CUNTR<0.50SM
188	Extra for providing edge moulding to 18mm Granite/ marble stone counters,Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in- Charge.
189	EXTRA FOR EDGE MOULDING TO GRANITE WORK
190	EXTRA FOR OPENING FOR WASH BASIN ETC.
191	MS GRILLS TO WINDOWS
192	CHROME PLATED FLOOR DOOR STOPPER
193	AL. HYDRAULIC DOOR CLOSER
194	100X72MM CHROME PLATED MORTISE LOCK
195	FACTORY MADE PVC DOOR FRAME
196	Providing and fixing factory made 30mm thick door shutter made of solid PVC foam profile. The styles & rails shall be of size 75mm x 30mm having wall thickness 5mm. The styles, top & bottom rails shall have one side wall thickness of 15mm integrally extruded on t he hinge side of the profile for better screw holding power. The styles and rails shall be reinforced with MS tubes of size 33mm x 1 7mm x 1mm painted with primer, all four corners of reinforcement to be welded or sealed. Solid PVC extruded bidding (push fit type) will be set inside the styles and rails with a cavity to receive single piece extruded 5mm PVC sheet as panel. The styles and rails shall be mitred cut and joint with help of PVC solvent cement and self tapping screws. Single piece extruded solid PVC lock rail of size 100mm x 30mm with wall thickness 5mm & 15 mm integrally extruded in the middle of the lock rail & fixed with styles with the he lp of PVC solvent cement & self driven self tapping screws of size 100mm x 8mm complete as per manufacturer's specifications and dir ection of Engineer-in-charge
197	FACTORY MADE NON DECO. PVC SHUTTERS
198	Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixed with rawl plugs and screws or w ith fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions,at top, bottom & sides with w ith required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanical ly wherever required including cleat angle, Aluminium snap beading for glazing/panelling, C.P. brass/stainless steel screws includin g fixing all complete as per drawing & the directions of Engineer-in-charge. (Cost of glazing or panels to be paid for separately)
199	POWDER COATED AL.SECN,FIXED GLAZING
200	POWDER COATED AL.SECN, SHUTTERS
201	Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminium doors, windows shutters and partition frames with C.P. brass/stainless steel screws etc. complete as per directions of Engineer in charge
202	PRE-LAM BOTH SIDE DECO.BOARD IN AL.SEC.
203	Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket e tc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be pa id in basic item):
204	FLOAT GLASS 6.0MM IN AL.SEC.
205	FLOAT GLASS 8.0MM IN AL.SEC.
206	Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS : 6315 having brand logo embossed on the body/plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in f loors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single pie ce M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge.
207	DBL ACTION FL.SPRING- BRASS COVER PLATE
208	FILLING GAP BY SILICON SEALANT
209	100MM BRASS LOCKS OF APPD.MAKE
210	Providing and fixing aluminium round shape handle of outer dia 100mm with SS screws etc. complete as per direction of Engineer-in- c harge
211	POWDER COATED AL.ROUND SHAPE HANDLE
212	P/FIXING 12MM FRAMELESS TOUGHENED GLASS
213	STRUCTURAL STEEL WORK IN SINGLE SECTION
214	STR.STEEL IN BUILT UP SECTION
215	ROLLING SHUTTERS
216	Steel work in built up tubular (round,square or rectangular hollow tubes etc) trusses etc. including cutting,hoisting fixing in posi tion and applying a priming coat of approved steel primer, including welded and bolted with special shaped washers etc. complete.
217	HOT FINISHED WELDED TYPE TUBULAR TRUSS
218	MS 16MM DIA FAN CLAMPS
219	MS GRATINGS,FRAMES,LADDER ETC.
220	CHEQUERRED PRECAST CC TILES IN FOOTPATH
221	25MM KOTA STONE FLOORING
222	25MM KOTA STONE IN STEPS
223	CERAMIC GLAZED TILES FOR WALLS
224	CERAMIC GLAZED TILES FOR FLOORING
225	Providing & laying vitrified floor tile in different sizes (thickness as per manufacturer) with water absorption's less than 0.08% a nd conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar as specified with coarse sa nd jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc. complete for flooring/skirting as specified
226	60X60 CM VITRIFIED FLOOR TILES
227	60X60 CM VITRIFIED TILES FOR SKIRTING
228	Providing and fixing Klippon Galvalume steel profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge ) of Cold rolled steel confirming to IS:513-2008 of base metal thickness 0.50 mm, having Yield Stress of Min. 275 MPa. Steel surface shall have hot dip metallic coating of Al-Zinc alloy comprising 55% Alluminium, 43.5% Zinc and 1.5% Silicon as per the ASTM-A792M, with total mass of coating on both sides shall be 150 gms/sqm. The steel shall have organic coating with Silicon Modified Polyester (SMP) /Super Durable Polyester (SDP) paint on continuous coil coating line. The thickness of coating on top side shall be 20-25 Micr ons (i.e. 15-18 microns SMP /SDP paint over 5-7 microns epoxy primer) and back side 8-10 Microns SMP/SDP paint over epoxy primer. To tal Coated Thickness (TCT) shall be 0.58 MM. Sheet shall have protective guard film of thickness of 25 microns minimum to avoid scra tches while transportation and should be supplied in single length up to 6m or as desired by Engineer-in-charge.
229	KLIPPON GALVALUME PLAIN SHEET RIDGES
230	KLIPPON GALVALUME PLAIN SHEET FLASHING
231	KLIPPON GALVALUME SHEET GUTTER
232	Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS:13592 Type A including jointing with sea l ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion, Single socketed pipes.
233	110MM PVC RAIN WATER PIPE
234	160MM PVC RAIN WATER PIPE
235	Providing & fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes confo rming to IS:13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.
236	110MM UPVC COUPLER
237	110MM UPVC SINGLE PUSHFIT COUPLER
238	UPVC SINGLE T WITH DOOR 110X110X110MM
239	UPVC SINGLE T WITHOUT DOOR - 110MM..
240	UPVC 87.5 DEGREE BEND OF 110MM
241	UPVC PLAIN SHOE OF 110MM
242	Providing & fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm h ard wood plugs, screwed with M.S. screws of required length including cutting brick work & fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.
243	110 MM UPVC PIPE CLIPS
244	150F/200F FALSE CEILING
245	PROVIDING & FIXING BARE KLIPPON GALVALUM
246	S & F 18 GAUGE GI PLAIN SHEET
247	Providing and laying cement plaster on surfaces with fine sand including curing etc.
248	12MM CEMENT PLASTER,1:6 WITH FINE SAND
249	20MM CEMENT PLASTER,1:6 WITH FINE SAND
250	Providing and laying 6mm thick cement plaster on surfaces with fine sand including curing etc.
251	6MM CEMENT PLASTER WITH FINE SAND
252	NEAT CEMENT PUNNING
253	2MM THK POP PUNNING OVER PLASTER
254	ACRYLIC SMOOTH EXTERIOR PAINT
255	DELUXE MULTI SURFACE PAINT SYSTEM
256	DELUXE MULTI SURFACE PAINT -WOOD WORK
257	DELUXE MULTISURFACE PAINT-STEEL SURFACE
258	SYNTHETIC ENAMEL PAINT
259	Demolishing cement concrete manually/ by mechanical means including disposal of material outside premises at an unobjectionable pla ce as per direction of Engineer-in-charge.
260	DEMOLISHING CC 1:3:6
261	DEMOLISHING BRICK WORK
262	DEMOLISHING STONE MASONRY
263	DISMANTLNG STEELWORK IN BUILTUP SECTION
264	Dismantling manually/by mechanical means including stacking of serviceable material & disposal of unserviceable material outside si te at unobjectionable place as per direction of Engineer-in-charge :
265	DISMANTLING WBM ROAD
266	DISMANTLING BITUMENOUS ROAD
267	DEMOL.CC/RCC WORK LEAD OF 1000M
268	Carriage charge for disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, stacking, unloading to approved municipal dumping ground/unobjectionable place as/direction of Eng g- in-Charge beyond IOCL Premises for all leads and including all lifts
269	MALBA & WASTE CARRIAGE > 1 km < 3 km
270	MALBA & WASTE CARRIAGE > 3 km < 5 km
271	PREPARATION OF SUB GRADE
272	Construction of granular sub-base by providing close graded material conforming to specifications, mixing in a mechanical mixer plan t at Optimum Moisture Content, carriage of mixed material by tippers to work site, for all lead and lifts, spreading in uniform laye rs of specified thickness with motor grader on prepared surface & compacting with vibratory power roller to achieve the desired dens ity, complete as per specification & direction of Engineer-in-charge.
273	GRANULAR SUB BASE -75MM TO 0.75MM
274	WET MIX MACADAM
275	Providing & laying factory made reflective type Lacquered finish Grey / coloured pre-cast cement concrete, interlocking paver block of specified grade made by block making machine wih vibratory compaction & of approved size and design / shape, shade and manufactur ers and as per IOCL's specifications. The paver blocks shall have peripheral chamfer, with average crushing strength as per IS 15658 , maximum water absorption of 2% after 10 minutes and 5% after 24 hrs. as per BS 1881, maximum dimensional deviations of +/- 2mm on length @ width and +/- 3 mm on thickness. The job includes supplying and laying a layer of 50 mm thick clean coarse sand on thorough ly compacted sub-base below the paver blocks, cutting the paver blocks wherever required with hydraulic splitter, filling in the joi nts at the edges of paver blocks with sand, compacting with machine vibrator to required line and level, etc. complete. (Payment for provision of edge restraints shall be made separately)
276	P/L REFLECTIVE LAQUERED M40 80MM THK PAV
277	Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 340x41 0x 265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :
278	1 URINAL - 5 L WHITE PVC AUTO-CISTERN
279	100MM SCI GULLY TRAP
280	600X450 BEVELLED EDGE MIRROR
281	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including a ll CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & f ittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Internal work - Expo sed on wall
282	CPVC PIPES 40MM INTRNAL EXPOSED ON WALL
283	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including al l CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fitting s with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work including cutting chases and making good the walls etc.
284	CPVC PIPES 15MM CONCEALED
285	CPVC PIPES 20MM CONCEALED
286	CPVC PIPES 25MM CONCEALED
287	CPVC PIPES 32MM CONCEALED
288	Providing and fixing brass bib cock of approved quality :
289	15MM BRASS BIB COCK
290	20MM BRASS BIB COCK
291	Providing and fixing brass stop cock of approved quality :
292	15MM BRASS STOP COCK
293	20MM BRASS STOP COCK
294	Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :
295	25MM GUN METAL VALVE WITH CI WHEEL
296	Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :
297	150MM DIA CP BRASS SHOWER ROSE
298	PROVIDING POLYETHYLENE TANK ON TERRACE
299	15MM CP BRASS LONG BODY BIB COCK
300	Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C. I.cover with frame of 300 x300 mm size(inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design :
301	100X100MM GULLY TRAP WITH COMMON BRICKS
302	Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in th e proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : Light Duty
303	150MM DIA NP2 CLASS RCC PIPES
304	SOAK PIT 2.5M DIA X 3M DEPTH
305	ATACTIC PP 5 LAY W.PROF TREAT-GLAS FIB.
306	WATER PROOFING WITH BRICK BAT COBA
307	Writing name of Retail Outlet and location/ Indian Oil Corporation monogram, other sign / slogans on building / glass of show windo w etc. of the following heights / diameters with vinyl sticker of approved quality and shade. 150 micron thick Non Reflective Vinyl sticker 3M or Equivalent Brand
308	LETTER SIZE UPTO 5CM
309	LETTER SIZE 6-15CM
310	LETTER SIZE 16-25CM
311	LETTER SIZE 26-70CM
312	FOUND.BOLT 25MMDIAX1.0M L,100X8MM PLATE
313	CABLING AND ALLIED WORKS - ARMOURED CABLES Supply & laying of XLPE insulated PVC sheathed aluminium/copper conductor, 1.1 kV grade armoured cable conforming to IS:7098, as per approved make in ground/ trench/surface/pipe, etc. whereever required as per direction of Engineer In-charge. Note: The rate of Installation should be inclusive of Cable clamps, tags Saddles, Consumables etc. Trays/pipe s, trenches, fabricated tray supports etc will be covered & paid in Separate Items
314	S&L 3X2.5 SQMM,1.1KV FRLS CU ARMD CABLE
315	S&L 4X2.5 SQMM,1.1KV FRLS CU ARMD CABLE
316	S&L 4X16 SQMM,1.1KV ALUMINIUM CABLE FRLS
317	S&L3.5X35 SQMM,1.1KV ALUMNM CABLE FRLS
318	S&L3.5X50 SQMM,1.1KV ALUMNM CABLE FRLS
319	S&L3.5X70 SQMM,1.1KV ALUMNM CABLE FRLS
320	CABLE TERMINATION GLANDS NON-FLP HEAVY DUTY DOUBLE COMPRESSION Cable Termination (NON FLP): Providing termination of 1.1 kV grade ar moured cable for the following sizes including supply of NON FLP heavy duty Double Compresson cable glands, crimping type lugs and allied jointing materials, etc. all complete as per specification and direction of Engineer In-charge. Glands and lugs shall be of approved make. Copper lugs for copper cables and aluminium lugs for aluminium cables shall be used.
321	CABLE TERM,NON FLP DC GLAND 3X2.5SQMM
322	CABLE TERM,NON FLP DC GLAND 4X2.5SQMM
323	CABLE TERM,NON FLP DC GLAND 4X16SQMM
324	CABLE TERM,NON FLP DC GLAND 3.5X35SQMM
325	CABLE TERM,NON FLP DC GLAND 3.5X70SQMM
326	CABLE BRICK DUCT Providing & constructing underground brick duct 650mm below GL for laying of 3 cables of max. diameter 70mm, comple te with supply and laying of sand, bricks & including Excavation and backfilling in all kind of soils
327	U/G 225MM WIDE BRICK DUCT FOR CABLE
328	50MM, CLASS B GI PIPE FOR CABLES
329	Supplying, fabricating and installing following sizes of perforated GI cable trays including horizontal and vertical bends, reducers , tees, cross members and other accessories as required and duly suspended from the ceiling and/or fix to steel/RCC columns, beams o r any other structure members with MS suspenders, angles, channels, etc complete as per the direction of IndianOil
330	PERFTD GI CABLE TRAY 150MM X 50MM X 2MM
331	S&F OF FLP JUNC. BOX (4 WAY ENTRY)
332	Supply & drawing/laying, jointing, connecting, testing and commissioning of earth strip/copper strip/GI wire for earthing and light ning protection under or aboveground complete as per specification for the following :
333	EARTHING WITH 25 X 3 MM GI STRIP
334	PROVIDING INTERNAL WIRING
335	LIGHT/FAN/5A POINT, WIRING, MOD SWITCH
336	Supplying, drawing sub-main/power wiring with PVC insulated Copper 1100 V grade FRLS type through heavy duty rigid PVC conduit eithe r on wall or in concealed. The job include terminations at both ends through proper jointing materials all complete for the followin g Make of Insulated wires shall be as per approved make
337	SUBMN WIRE-2X1.5SQMM,EARTHWIRE 1X1.5SQMM
338	SUBMN WIRE-2X2.5SQMM,EARTHWIRE1X2.5SQMM
339	SUBMN WIRE-2X4SQMM,EARTHWIRE 1X4SQMM
340	SUBMN WIRE-2X16SQMM,EARTHWIRE 1X16SQMM
341	SWITCHES, FUSES, MCBS, ELCBS ETC Supply and fixing of Modular switch frame with inner and outer face plates and accessories as per f ollowing details of approved including flush metal boxes/surface mounting boxes, plates, etc. all complete as per manufacturer's sp ecification and direction of Engineer In-charge.
342	S&F SWITCH WITH 1 OR 2 MODULE FRAME
343	S&F SWITCH WITH 3 MODULE FRAME
344	S&F SWITCH WITH 4 MODULE FRAME
345	S&F SWITCH WITH 6 MODULE FRAME
346	S&F SWITCH WITH 8 MODULE FRAME
347	S&F SWITCH WITH 12 MODULE FRAME
348	S&F 6A MODULAR SWITCH
349	S&F 15 A MODULAR SWITCH
350	S&F 6A, 3 PIN MODULAR SOCKET
351	S&F 15 A 6 PIN MODULAR SOCKET
352	S&F FAN REGULATOR OF STEPPED MODULAR
353	Supply & fixing of 300mA RCCB of approved Make of following ratings:
354	S&F RCCB - 4 POLES, 63A
355	Supplying and fixing of following MCBs with necessery inter connections on existing DB, Panel board etc.
356	S&F MCB+ELCB UPTO 32A SP MCB
357	S&F MCB+ELCB UPTO 32A DP MCB
358	Supply and installation of MCB distribution board having Double door complete with tinned cu bus bar, neutral bus bar, earth bar, din bar, interconnection, earthing etc. without incoming isolator and MCBs
359	S&F MCB DB WITH 4 WAY (4+12) TPN
360	SWITCH FUSE UNIT WITHOUT FUSE Supply & fixing switches/accessories in sheet metal enclosure including providing of required connec tions with supply of necessary cable/conduits as required in case of existing control switch panel/ switch board etc. all complete as per specification and direction of Engineer-In-Charge.( SFUs shall be of approved make and SFUs shall be without fuse)
361	S&F 100AMP TPN SWITCH FUSE UNIT
362	HOARDING LIGHTS:30W WITH IP65 PROTECTION
363	LED TUBE LIGHT: 18W WITH IP65 PROTECTION
364	LED TUBE LIGHT: 8W WITH IP20 PROTECTION
365	CEILING FANS Supply & fixing of ceiling fan for inside of the sales building of following type:
366	S&I 1200 MM SWEEP CEILING
367	EXHAUST FANS Supply and fixing of exhaust fan including electrical wiring all shall be with per specification and direction of site In charge. The fans shall be with louvers / shutters. (The job does not include making suitable cut out in the wall for fixing the fan).
368	S&I 9\\" LIGHT DUTY EXHAUST FAN KHAITAN/EQ
369	Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make
370	Providing and fixing H type double tone SS Pull handle of GODREJ (7268) or equivalent make
371	Providing and fixing Chrome Finish SS Health faucet with 8mm dia, 1 meter long
372	Stainless Steel Handrail:Providing and fixing
373	Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-c hambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape and size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame and sash shall be mitred cut and fusion welded at all corne rs, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjace nt finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all co mplete as per approved drawing and direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shal l be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth and width of profile shall be a cceptable.
374	Two track two panels sliding window made of (small series) frame
375	Providing and fixing factory made uPVC white colour casement/ casement cum fixed glazed windows comprising of uPVC multi- chambered frame, sash and mullion (where ever required) extruded. profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel sect ion made from roll forming process of required length (shape and size according to uPVC profile), uPVC extruded glazing beads of app ropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame and sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion weld ed including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacen t finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all com plete as per approved drawing and direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid se parately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account account shall be mad e. Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth and width of profile shall be acceptable.
376	Casement window single panel with S.S. friction hinges
377	WALL HUNG COMMODE
378	Providing & fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes confo rming to IS:13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.
379	160MM UPVC COUPLER
380	160MM UPVC SINGLE PUSHFIT COUPLER
381	UPVC SINGLE T WITH DOOR 160X160X160MM
382	UPVC SINGLE T WITHOUT DOOR - 160MM
383	UPVC 87.5 DEGREE BEND OF 160MM
384	UPVC PLAIN SHOE OF 160MM
385	S/F UNDER CANOPY RECESS MOUNTED 80W LINEAR LIGHT (2.4 m)
386	COUNTER SUNK WASH BASIN Please Enable Macros to View BoQ information

Tender Documents

SR No	FileName	File Description
1	Click here to download tender document	Tender Documents
2	Click here to download tender document	Tender Documents
3	Click here to download tender document	Tender Documents
4	Click here to download tender document	Tender Documents
5	Click here to download tender document	Tender Documents
6	Click here to download tender document	Tender Documents
7	Click here to download tender document	Tender Documents
8	Click here to download tender document	Tender Documents
9	Click here to download tender document	Tender Documents
10	Click here to download tender document	Tender Documents
11	Click here to download tender document	Tender Documents
12	Click here to download tender document	Tender Documents
13	Click here to download tender document	Tender Documents
14	Click here to download tender document	Tender Documents

Also Visit

Tenders

West Bengal Tenders

Construction Tenders

Excavation Tenders

Land Development Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Development Of New A Site Regular Retail Outlet At Location-On Sh-8 From Bankura More To Khejurhati Bus Stand, Dist-Purba Bardhaman Under Durgapur Divisional Office Of West Bengal State Office, Purba Bardhaman-West Bengal

Tender Documents

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Development Of New A Site Regular Retail Outlet At Location-On Sh-8 From Bankura More To Khejurhati Bus Stand, Dist-Purba Bardhaman Under Durgapur Divisional Office Of West Bengal State Office, Purba Bardhaman-West Bengal

Tender Documents

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us