|
| 1 | Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing, spreading or stacking the spoils within a lead of 75 m. as directed. The item includes necessary trimming the trenches, levelling, dressing and ramming the bottom, bailing out water as required complete. a) Depth of excavation not exceeding 1,500 mm. |
| 2 | Earth work in filling in foundation trenches or plinth with good earth, in layers not exceeding 150 mm. including watering and ramming etc. layer by layer complete. (Payment to be made on the basis of measurement of finished quantity of work)---(a) With earth obtained from excavation of foundation. |
| 3 | Single brick flat soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with powdered earth or local sand. |
| 4 | Cement concrete with graded stone ballast (40 mm size excluding shuttering). In ground floor and foundation.(A) Pakur Variety. 1:3:6 proportion. |
| 5 | Hire and labour charges for shuttering with centreing and necessary staging upto 4 m. using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams, columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor).--- a) 25 mm to 30 mm thick wooden shuttering as per decision & direction of Engineer-In-Charge.In i) Gr. floor. |
| 6 | (b) 25 mm to 30 mm shuttering without staging in foundation etc. |
| 7 | Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups,binders etc. including supply of rods, initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bennding to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction.i) JSW /JSPL /SHYAM /SRMB /BMASL/ ELECTROSTEEL/SSL(a) In Ground Floor and Foundation. |
| 8 | Ordinary Cement concrete (mix 1:2:4) with graded stone chips (20 mm.nominalsize) excluding shuttering and reinforcement, if any, in ground floor as per relevant IS codes.--a) Pakur Variety. |
| 9 | Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips(20 mm.nominal size) excluding shuttering and reinforcement, if any, in ground floor as per relevant IS codes. (i) Pakur Variety.( I ) In Ground Floor & Foundation. |
| 10 | A) Brick work with 1st. Class bricks in C.M. ( 1: 6) (a) In foundation and plinth |
| 11 | 125 mm. thick brick work with 1st class bricks in cement mortar (1:4) in ground floor. ( a ) Gr. Floor. |
| 12 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Exxcluding cost of chipping over concrete surface.] (i) With 1:6 cement mortar (a) 20 mm. thick plaster . In ground floor. |
| 13 | (b) 15 mm. thick plaster. In ground floor. |
| 14 | (ii) With 1:4 cement mortar. (a) 10 mm. thick plaster In ground floor. |
| 15 | Neat cement punning about 1.5 mm. thick in wall, dado, window, sills, floor, drain etc. NOTE: Cement 0.152 cu. M. per sq.m. |
| 16 | 18 mm to 22 mm thick, kota stone slab set in 20 mm thick (avg) cement mortar (1:4) in floor, stair & lobby including pointing in cement slurry with admixture of pigment matching the stone shade, including grinding & polishing as per direction of Engineer - in - charge to match with the existing work. [Slurry for bedding @ 4.4 kg/Sq.m and pointing @ 2.0 kg/Sq.m]. In ground floor. |
| 17 | Laying of 38 mm thick Acid Proof tiles in floor, walls and drains with acid proof mortar including application of primer, two layers of special mastic membrane topped by 6 mm layers of potassium silicate mortar as under bed and painting the joints (upto 15 mm) with acid / alkali proof epoxy mortar, cement including preparing surface by cleaning old mastic membrane all complete as per specification and direction of EIC including cost of tiles to be supplied by the contractor at his risk and cost. |
| 18 | Supplying, fitting and fixing Marble Slab/Tile of 15 to 18 mm thickness in floor, lobby, stair, landing & treads etc. over 20 mm (av0 thick base of Cement mortar (1:2) laid with white cement slurry @ 4.4 kg/Sq.m before placing marble & jointed with white cement slurry @ 2.0 kg/Sq.m with necessary pigments including grinding and Granite polishing as per direction of Engineering -in- charge. (White cement and Pigment to be supplied by the Agency)-- (a) With Makrana plain pink/ Adranga Pink/ Makrana plain pink/ Garbh Gulabi/ Udaypur Green/ Black Bhaslana.-- (ii)Area of EACH Slab/ tile exceeding 0.3 sq.m. but not exceeding 0.6 sq.m.(a)In ground Floor |
| 19 | Supplying fitting & fixing 1st quality Ceramic Tiles in walls & floors to match with the existing works and four no of key stones (10mm) fixed with araldite at the back of EACH tiles and finishing the joints with white cements mixed with colouring oxide if required, to match the colour of tiles including roughening of concrete surface , if necessary, or by synthetic adhesive and grout materials etc.----.(A) Wall With sand cement mortar using white cement slurry @ 0.20 Kg/sqm.Area of EACH tile upto 0.09 sqm Other than Coloured Decorative including white.(a) In Ground floor. |
| 20 | Supplying and laying chequered tiles of any shade & ofapproved quality with (1:1½:3) cement concrete laid in panelsor patterns as directed in pavement, footpath etc. includingnecessary underlay 25 mm thick [avg] cement mortar (1:3)complete in all respect with all labour and materials. [Usingcement slurry @ 4.4 kg/Sq.m at back side and @2.4 kg/Sq.mfor joint filling] Red Variety (i) 25 mm. thick |
| 21 | iv) Two point nose steel handle including fitting and fixing. |
| 22 | vi) steel peg stay 300 mm long including fitting and fixing. |
| 23 | Supplying best Indian sheet glass panes set in .. with nails and putty complete. (In all floors for internal wall.. for external wall).(i) 4 mm thick (weighing 7.4 kg/Sq.m) |
| 24 | Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame excluding cost of concrete, Iron Butt Hinges and M.S. clamps. (The quantity shoud be corrected upto three decimals).--- Sal : Local. (a) In Ground Floor |
| 25 | Supplying solid flush type doors of commercial quality, the timber frame consisting of top and bottom rails and side styles of well seasoned timber 65mm wide EACH and the entire frame fitted with 37.5mm wide battens places both ways in order to make the door of solid core and internal lipping with Garjan or similar wood vveneers using phenol formaldehyde as glue etc. complete, including fitting, fixing shutters in position but excluding the cost of hinges and other fittings . 35 mm thick shutters (single leaf)--(a) In Ground Floor |
| 26 | Supplying, fitting and fixing M.S. clamp for door and window frame made of flat bent bar, end bifurcated with necessary screws etc. by cement concrete (1:2:4) as per direction.(Cost of cement concrete will be paid separately)--(The concreting will have to be done for equivalent thickness of 2 layers of brick work and for the entire width of the wall. No deduction on brick work will be made).40mm. X 6mm, 125mm. Length. |
| 27 | Iron butt hinges of approved quality fitted and fixed with steel screws, with ISI mark.(vi) 100mm. X 50mm. X 1.25mm. |
| 28 | Supplying concealed type heavy duty PVC headed aluminium tower bolt for double leaf doors as per approved make and brand as per direction of Engineer-in-Charge.(a) 250 mm long |
| 29 | Iron hasp bolt of approved quality fitted and fixed complete (oxidised) with 16mm dia rod with centre bolt and round fitting.(c) 300mm long. |
| 30 | Supplying 125 mm. Dia. Acrylic handle for aluminium door as per approved make and brand. (a) natural colour. |
| 31 | Supplying, Fitting & Fixing Factory made P.V.C. door frame of size 50 mmx47 mm with a wall thickness of 5 mm, made out of extruded 5 mm, PVC sheet miter cut at two corners and joined with two nos of 1.5 mm long brackets of 15 mm x15 mm M.S. square tube. The two vertical door profiles are to be reinforced with 19 mmx 19 mm M.S. Square tube of 19 gauge, weather seal to be provided through out the frame. The door frame shall be fixed with the wall using 65/100 mm long M.S. Screws through the frame by using P.V.C fasteners. A minimum of 4 Nos ofscrews to be provided for EACH vertical member and minimum 2 Nos for horizontal member etc. complete as per Manufacturer‟s specification and direction of Engineer-in-Charge. |
| 32 | Supplying, Fitting & Fixing 30 mm thick Factory made solid Panel PVC Door Shutter consisting of outer frame made out of M.S. tubes of 19 gauge thickness and size 19 mmx19 mm for styles, top and bottom rails, M.S. frame shall have costof steel primers of approved make and manufacture, M.S. frame covered with 5 mm th. heat moulded PVC “C” channel of size 30 mm th, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on either sides forming styles; and 5 mm th. 95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm tapered in 45 degree on the inner side to form top & bottom rail and 115 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided either side of the panel with 10 mm (5 mmx2) th.,20 mm wide cross PVC sheet as gap insert for top rail and bottom rail. Paneling of 5 mm th. both side PVC sheet to be fitted in the M.S. frame welded/sealed to the styles &rails with 7 mm (5 mm+2 mm) th.x15 mm wide PVC sheet beading on inner side and joined together with solvent cement adhesive. An additional 5 mm th. PVC strip of 20 mm which is to be stuck on the interior side of the “C” channel using PVC solvent adhesive etc. complete excluding all necessary hardwares as per direction of Engineer-in-charge |
| 33 | Rendering the surface of walls and ceiling with white cement based wall putty of approved make and brand(1.5mm thick). |
| 34 | Applying Interior grade Acrylic Primer of approved quality and brand on plastered or concrete surface old or new surface to receive distemper / acrylic emulsion paint including scrapping and preparing the surface thoroughly, complete as per manufacturer's specification and as per direction of E.I.C One coat. i) Water based interior grade acrylic primer. |
| 35 | Applying Acrylic emulsion paint of approved make and brand on walls and ceiling including sand papering in intermidiate course including putty (two coats). Standard Quality. |
| 36 | Protective and decorative Acrylic exterior emulsion paint of approved quality, as per manufacturer's specification and as per direction of EIC to be applied over acrylic primer as required.The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer.--- a) Normal Acrylic Emulsion .(Two Coat).i) In ground floor. |
| 37 | Applying Exterior grade Acrylic Primer of approved quality and brand on plastered or concretesurface old or new surface to receive decorative textured (mat finish) or smooth finish acrylic exterior Immersion paint including scrapping and preparing the surface thoroughly, complete as per manufacturer's specification and as per direction of E.I.C (One coat on new surface.)----- a) In ground floor. |
| 38 | Priming one coat on timber or plastered or surface with synthetic oil bound primer of approved quality including smooth ening surfaces by sand papering etc. (This item is applicable to new work or old work when the original..removal of old paint.) |
| 39 | Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. |
| 40 | Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary. (a) On timber or plastered surface : With other than (hi-gloss) -(iv) Two coats (with any shade except white) |
| 41 | (b) On steel or other metal surface : : With other than (hi-gloss) -(iv) Two coats (with any shade except white) |
| 42 | Glazing clip |
| 43 | Supplying EPDM gusket of approved make and brand as per direction of Engineer in charge.--For Openable/ Casement windows..b) 'U' shaped EPDM gasket for frames. |
| 44 | c) Weather gasket / Wool pile for door vertical. |
| 45 | Anodised aliminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 230/72) fitted and fixed complete:--(a) With continuous plate base (hexagonal/round rod)(v) 125mm grip x 12mm dia rod. |
| 46 | Supplying 4 lever mortice lock or any approved make and brand as per direction of the Engineer- in -charge.--I) 100 mm. |
| 47 | Supplying heavy duty hydraulic double action floor spring along with top pin/set of pivots conforming to IS: 6315 or any approved make as per direction of Engineer in charge. |
| 48 | Hydraulic door closer of approved quality as per I.S.I. standard fitted and fixed complete.(a) Heavy type (I.S.I. size 3) (i)40mm. X 6mm, 125mm. Length. |
| 49 | Steel body foot-door holder. |
| 50 | Supplying, fitting and fixing PVC pipes of approved makeof (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket reducing tee, short piece etc. fitted with holder bats clamps, including, cutting pipes, making threads,fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above ground. Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. Payment for painting will be made seperately) PVC Pipes(Dia)( I )20 mm Dia |
| 51 | 25 mm Dia |
| 52 | 32 mm Dia |
| 53 | Supplying, fitting and fixing gunmetal wheel valve of approved brand and make tested to 21 kg per sq. cm. (for water lines only)a) 32 mm. dia. |
| 54 | b) 25 mm. dia. |
| 55 | PTMT (Polytetra Bib Cock / Stop Cock ( Prayag or equivalent) 15 mm |
| 56 | Supplying, fitting and fixing pillar cock of approved make. b) PTMT Pillar Cock - 15 mm. (Prayag or equivalent). |
| 57 | g) PTMT overhead shower ( Prayag or equivalent) (i) 75 mm round |
| 58 | Wash basin white vitreous china of approvedmake (without fittings) supplied, fitted and fixed in position on 75mm X 75mm X 75mm. Wood blocks and C.I. brackets including two coats of painting of C.I.brackets.(ii) 550 mm X 400 mm. |
| 59 | Supplying, fitting and fixing stainless steel sink complete with waste fittings and two coats of painting of CI brackets. (ii) 530 mm. X 430 mm. X 180 mm. |
| 60 | Supplying, fitting and fixing Flat back urinal (half stall urinal) in white vitreous chinaware of approved make in position with brass screws on 75 mm. x 75 mm. X 75 mm. wooden blocks complete..(ii) 470 mm X 280 mm X 340 mm |
| 61 | Supplying,fitting and fixing approved brand 32 mm dia.P.V.C. waste pipe, with PVC coupling at one end fitted with necessary clamps.(i) 750 mm long |
| 62 | Supplying, fitting and fixing E.W.C. in white glazed vitreous chinaware of approved make complete in position with necessary bolts, nuts etc.(a) With 'P' trap (with vent). |
| 63 | Supplying, fitting and fixing Closet seat of approved make with lid and C.P. hinges, rubber buffer and brass screws complete.(a) E.W.C.(i) Plastic (hollow type) white. |
| 64 | Supplying, fitting and fixing 10 litre P.V.C. low-down cistern conforming to I.S. specificatioons with P.V.C. fittings completre, C.i. brackets including two coats of painting to bracket etc. |
| 65 | Supplying,fitting and fixing 32 mm dia. Flush Pipe of approved make with necessary fixing materials and clamps complete i) Polythene Flush Pipe |
| 66 | Supplying,fitting and fixing approved brand P.V.C. CONNECTOR white.. C.P. nut, 15 mm dia.(i) 450 mm long |
| 67 | Supplying, fitting and fixing best quality Indian make mirror 5.5 mm. thick with silvering as per I.S.I specifications supported on fiber glass frame of any colour, frame size 550mm x 400mm. |
| 68 | Supplying, fitting and fixing towel rail with two brackets.(a) C.P. over brass(i) 25 mm. dia. and 600 mm. long. |
| 69 | Supplying, fitting and fixing porcelin soap tray of approved make.(i) Recessed soap tray of size 150 mm. X 150 mm. |
| 70 | Supplying P.V.C. water storage tank of approved quality with closed top with lid (Black) - Multilayer. 1000 litre capacity |
| 71 | Labour for hoisting Plastic water storage tank. Up to 1500 litre capacity. |
| 72 | Labour for punching hole in plastic water storage tank up to 50 mm dia. |
| 73 | Supplying fitting & fixing UPVC Pipes A type and fitttings conforming to IS 13592-1992 with all necessary clamps, nails including making holes in walls, floors etc cutting trenches in any soil through masonary concrete structures etc, if necessary, and mending good damages including joining with jointing materials.(for rain water draining) A.) UPVC Pipes of 110 mm dia. |
| 74 | B) Plain Tee (UPVC), 110mm dia. |
| 75 | C) UPVC Shoe, 110mm dia. |
| 76 | D) Bend 87.5 degree of 110mm dia. |
| 77 | Fabrication, supplying, fitting & fixing of cable trenches covers with 6 mm. thick M. S. chequered plate having 2 nos. 10 mm. dia. M. S. lifting hooks, strengthening the plate by welding 2 nos. 16 mm. dia. M. S. bar at bottom (length wise) including supplying, fitting & fixing of 25 x 25 x 5 mm. M. S. angle seats of both side of trenche as per drawing & direction complete with all labour & materials. |
| 78 | M.S. structural works in columns, beams etc. with simple rolledstructural members (e.g. joists, angle, channel sections conformingto IS: 226, IS: 808 & SP (6)- 1964 connected to one another withbracket, gussets, cleats as per design, direction of Engineer-incharge complete including cutting to requisite shape and length,fabrication with necessary bolting, metal arc welding conforming to IS: 816- 1969 & IS: 1995 using electrodes of approved make and brand conforming to IS:814- 2004, haulage, hoisting and erection all complete. The rate includes the cost of rolled steel section, consumables such as electrodes, gas and hire charge of all tools and plants and labour required for the work including all incidental chages such as electricity charges, labour insurance charges etc.-----I) For structural members of specified sections weighing less than 22.5 Kg./m |
| 79 | Applying 2 coats of Non-Toxic Acrylic Polymer modified Paint having adhesive & waterproofing properties by mixing in proportion (1 liquid: 4 cementitious material) or as per manufacturer's specification for water proofing layer in water tank etc. (No Departmental Cement is required) |
| 80 | Supplying Crushed stone ( Trap stone ) shall be of 40 mm ( Ungraded ) nominal size. (40 mm size). Pakur Variety.(Payment will be made on basis of measurement after deduction of shrinkage, shinkage). (Washing should be done before spreading of gravels over base). |
| 81 | M.S. gate of Jail type as per approved design made of strong M.S. frame work, intermediate stiffeners and round / square bars orangles. M.S. sheet (not less than 14 gauge) gussets, cleats etc.including necessary riveting, bolting, welding, locking and hangingarrangements, fitting and fixing complete as per direction of theEngineer-in -charge. In ground floor |
| 82 | Supplying fitting and fixing 600 mm ( ±30 mm) diametre R.B.T (Reinforced Barbed Tape) Concertina fencing on wall top using concertina coils stretched to approx.6 meters length at site clipped with two nos. of horizontal R.B.T strands which will be tensioned and fixed with the vertical M.S angle iron posts by means of security fasteners (such as 'C' clips, R.B.T clips etc.) |
| 83 | Supplying, fitting, fixing, Chain link fencing of approved quality with R.C.C posts wooden posts or iron posts by means of galvanised \\"C\\" clips to grid of horizontal strands of galvanised high tensile spring steel wire of 12 S.W.G which have to be tensioned and fixed to the vertical posts by means of galvanised special clips, bolts and nuts etc.(The rate is exclusive of the cost of posts)(I) 25 mm. x 25 mm. x 12 g. Please Enable Macros to View BoQ information |
