|
| 1 | Dismantling roof treatment of any description including cement mortar bedding(But not backing)cleaning the surface by blowing,washing and rubbish off the premises complete all as directed.(a) M&L for10 mm thick rendering on fair faces of brick works / Concrete surfaces finished even and smooth without using extra cement in cement mortar 1: 3complete all as specified and as directed(b) M&L for priming evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 Kg per sq.m including cleaning the surface.(c) M&L App based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforment with polyster non woven fabric (wt reinforcement not less than 150 gms/sqm) laid on primed surfaced application complete all as apecified and directed (Primer should be measured and paid as per Item above).(d) M&L applying two coat of Aluminium paint over APP Membrane complete all as apecified and directed. |
| 2 | Cutting out cracks to V section in existing roofs or terracing ,cleaning out ,wetting, grouting with cement and sand slurry 1:3 |
| 3 | M&L for 25mm thick PCC type B0 (1:2:4) using 12.5 mm graded crushed aggregate in padding concrete and the like all as specified and directed. |
| 4 | Supply only liquid waterproofing compound. |
| 5 | Taking down cement plaster on brick/stone/concrete surface including wall tiling and hacking out joints hacking for key scrubbing down with water etc complete |
| 6 | M & L rendering 20mm thick on surface of stone masonary surface in CM 1:6 and is to be finished even and smooth with out using extra cement complete all as specified directed |
| 7 | M & L for 20mm thick cement plaster in CM 1:4 on fair faces of stone masonary surfaces and finishing the surface even and smooth (without using extra cement) etc. |
| 8 | M & L for 5mm thick ceiling cement plaster in CM 1:4 on fair faces concrete surfaces and finishing the surface even and smooth (without using extra cement) etc. |
| 9 | M&L for 1mm thick wall care putty on wall all as specified and directed by Engr in Charge. |
| 10 | M & L for two coats of distmepring with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre of approved munufacutre of required shade and colour complete as per munufacuters specification two or more coat on new work all as specified and directed. |
| 11 | M&L for finishing new/old plastered surfaces of walls with Acrylic smooth exterior paint of required shade Camouflage pattern applying two or more coats applied @ 1.67Ltr/10 Sqm over and including priming coat of exterior primer allpied @ 2.20Kg/10Sqm all as specified and directed. |
| 12 | Preparation of ceiling surfaces and applying two coats of white wash on surface of on ceiling /soffits of slabs, chajjas all as specified and as directed. |
| 13 | Demolition of cement concrete in ground floor and pavings n'exc 15cm thickness (below or above ground level complete all as specified and as directed). |
| 14 | M & L for 75 mm PCC 1:3:6 type C-2 using 20mm graded aggregate as plinth protection finished even and smooth with out using extra cement |
| 15 | M&L Forming Contraction (Dummy) joints 75 mm deep x 10mm wide for plinth protection & similar work , filled with sealing compound Grade 'B' in plinth protection |
| 16 | Dismantling floor hearth or wall tilling including cement mortar bedding (but not backing ) removing serviceable tiles to store and rubbish off the premises |
| 17 | M & L for 25mm thick PCC 1:2:4, type B-0, (using 12.50 mm graded stone aggregate) as in under layer of tile flooring & finishing the surfaces rough to receive screed bed complete as specified and directed. |
| 18 | M&L for Non skid ceramic coloured tiles 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18sqm in floor, over 15mm thick screed bed in CM 1:6 on floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade as specified and as directed. |
| 19 | M&L for glazed ceramic coloured tiles in vertical surfaces of size 350X250X7/450X350X7 mm thick set and jointed in neat cement slurry and pointed in coloured cement as in vertical surfaces such as dado/skirting and facea of side bldg over & including 10mm thick rendering in CM(1:4) complete all as specified and as directed. |
| 20 | M&L for vetrified ceramic tiles 10mm thick full body (light shade ) (square/rectangular) polished, area of each tiles not exc 0.36 sqm in floors over 15mm thick screed bed in CM 1:6 on floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade as specified and as directed. |
| 21 | M&L for machine cut mirror polish kota stone slab flooring 20-25mm thick over 15mm thick cement screed base in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including round nosing at corners ,rubbing and mirror polishing complete as specified and as directed. |
| 22 | M&L for machine cut mirror polish kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar over 10mm thick cement screed base in CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including round nosing at corners ,rubbing and mirror polishing complete as specified and as directed. |
| 23 | M&L for Sand filling under floors or in foundations including watering and consolidation |
| 24 | Taking down chowkats / frames with shutters (without taking off shutters from the frames) area n'exc 1.5 Sqm each complete all as directed by Engr-in-charge. |
| 25 | Taking down chowkats or frames with shutters (without taking off shutters from the frames) area exceeding 1.5 Sqm and not exceeding 4 Sqm each complete all as directed by Engr-in-charge. |
| 26 | S&F mild steel work as in hold fasts and similar work confirming to Fe-290 or Gd -E 165 complete.all as specified and as directed by the Engr-in-Chage |
| 27 | Material & labour PCC (1:3:6) type C1 (using 20 mm graded stone aggregate) as in hold fast , bed block and like complete all as specified and as directed by the Engr-in-Charge. |
| 28 | M& for Pressed steel frames of size 105x60mm for doors with one or more rebates including necessary fixings lugs,excluding hinges,lock strike plate,etc,complete ,as specified ,supplied and fixed.(PCC filling of hollow section measured and paid seprately) |
| 29 | M & L PCC type C-0,1:3:6 (12.5mm graded stone aggregates) for cills,hold fast filling of hollow of pressed steel door frame etc |
| 30 | S&F for 30mm thick 2nd class hard wood plain framed panelled shutters (any number of panels) with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers, Supply and fixed to chowkats , complete all as directed by Engr-in-charge. |
| 31 | M&L for 40mm thick solid core construction, with block board core and plywood face panels, commercial ty[pe on both sides |
| 32 | M& for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60(Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note: a) M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately. b) For WPC solid door/window frames,minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 33 | M&L Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.Note: including stainless steel butt hinges and necessary S S screws. |
| 34 | S&F Steel windows/ventilators (frame with shutter) with side hung shutters including box type hinges with steel handle ,and steel peg stay,complete with glazing bars,dovatiled or welded (Glass/Wire mesh shall be measured Seperately)complete all as specified and directed by Engineer-in-Charge. |
| 35 | S&F MS framedwork such as grills, gratings etc with ends of bars shouldered and/or rivited or forged in spikes, framed guard bars, barred iron doors, ledders framed balsters walk ways railings frame work of water tanks and similar work confirming to Fe-290, Gde-E-165 complete all as specified and as directed. |
| 36 | M&L for Powder Coated (Minimum thickness of powdercoating 50 micron) aluminium frame of standerd section for doors, windows, ventilators and partitions with double rebates including joining cleat for fixing etc. complete all as specified |
| 37 | S & F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge (For sliding window ) |
| 38 | M&L sheet glass 4.8mm thick ordinalry quality and glazing with aluminium beeds in square exc 0.50 sqm in each pane complete all as specified and as directed |
| 39 | M&L sheet glass 3mm thick ordinalry quality and glazing with oil putty or wooden beads in square not exc 0.50 sqm in each pane complete all as specified and as directed. |
| 40 | S&F in repairs Aluminium (extruded section) door closer hydraulically regulated ,designation No.3, universal type, suitable for door shutter of 851 to 1000mm in width and of weighjt between 61 to 80 Kg all as specified and as directed. |
| 41 | S&F in 100mm Aluminium Mortice lock 2 livers vertical type complete all as specified and as directed. |
| 42 | S&F mild steel butt hinges, medium weight cold rolled 100mm size complete all as specified and as directed. |
| 43 | S&F 150mm long aluminium anodized, barrel tower bolt of extruded section complete all as specified and as directed. |
| 44 | S&F 150mm size extruded aluminium alloy handles, fabricated type, anodized complete all as specified and as directed. |
| 45 | S&F Aluminium alloy anodised ,sliding door bolt 250mm with hasp,staple(bolt type) and fixing clips of sheet ,cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast, aluminium alloy complete all as specified and as directed. |
| 46 | M&L preparing newly wood or wood based surfaces of any description over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 47 | S&F of Collapsible steel gates side hung, considering of channel pickets , pivoted flat bars, top and bottom runners,handles etc, as specified,errected in position and securing runners with hold fasts and brackets, complete all as specified and directed by Engr-in- Charge |
| 48 | M&L Hand rails, grills ,Gates ,half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof ,Brackets for Valley gutters ,including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe 410-0 or FE 310-0 complete all as specified and directed by Engr-in- Charge |
| 49 | S&F 1.25mm thick mild steel, plain black sheet in wall cladding, steel gates and similar work, cut to size, holes punched, including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. |
| 50 | M & L for preparation of new steel surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer. all as directed and specified. |
| 51 | Taking down Rolling shutters of any description area exceeding 8.00 Sqm and not exceeding 20.00 Sqm each complete all as directed by Engr-in-charge. |
| 52 | S&F Steel rolling shutters with thicknes of each laths of 1mm thick,with out ball bearing ,as specified,including top cover anchoring rod ,hasp and staple and one shop coat of primer;erected in position as indicated,complete:push pull or manual type complete all as specified and as directed |
| 53 | S & F in repairs 50mm bore MS pipe for suspension shafts for rolling shutter all as directed. |
| 54 | Supply only interlocking lath sections made out of cold rolled steel strips of 1.00 mm thick and 75mm width complete all as specified in SSR and as directed. |
| 55 | Taking up or down steel tubing and connections, including cleaning for re-fixing or removal 15mm dia |
| 56 | Taking up or down steel tubing and connections, including cleaning for re-fixing or removal 20mm dia |
| 57 | Refixing 15mm bore old steel water tubing and connection in new or old position (walls, ceilling, floor etc) |
| 58 | Refixing 20mm bore old steel water tubing and connection in new or old position (walls, ceilling, floor etc) |
| 59 | M&L for GI tubing 15mm dia medium grade with all fittings & fixed complete to walls & ceiling or laid in floors in repairs |
| 60 | M&L for GI tubing 20mm dia medium grade with all fittings & fixtures complete laid in trenches fixed in repairs |
| 61 | M&L for cutting chases, pinning in making good to face for concealed water tubing in stone concrete blocks or slab walls all as specified and directed. |
| 62 | Dismantling water tank exc 500 and n exc 1000 ltrs and remvoing to all as specified and directed. |
| 63 | S&F cylindrical type, three layer & white colour rotational moulded polyethylene water storage tank of 1000 ltr capacity ISI marked (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Pt-I with 25 mm ball valve high pressure PTMT with rod & high density plastic ball complete all as specified and directed by Engineer-in-Charge. |
| 64 | S&F in repair vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) , Pedestal pan and trap including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe etc complete, Plastic water closet seat cover, black closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device all as specified and directed. |
| 65 | S & F in repair Vitreous China wash basin, white, flat back, size 550 x 450mm including brackets all as specified and directed. |
| 66 | S&F in repairs Vitreous China Half stall Urinal, flat back, white with grating and union for discharge pipe and PTMT waste coupling with waste pipe (excluding flushing cistern, flush pipe and waste pipe) |
| 67 | S&F in repairs, 10 litres capacity PVC valveless syphonic action type, flushing cistern (ISI marked), low level with inlet, ball valve, float bracket & flush pipe complete all as specified & directed. |
| 68 | S&F in repairs waste pipe of polyethylene of low or high density or PVC ,32 mmdia for urinal/wash basin/Kitchen sink/ flush tank complete all as directed by Engr-in-charge. |
| 69 | S&F in repairs PVC connection pipe suitable for connecting flushing cistern and WHB etc 450mm long complete all as specified and directed. |
| 70 | S & F in repairs, waste coupling of PTMT 32mm bore for urinal / wash basin (Half or full threaded ) (Minimum Weight 45 grams) |
| 71 | S&F in repairs 600x450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial ply wood and fixed to wooden plugs with cromium plated brass screws and cup washers complete all as specified. |
| 72 | S & F in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified . |
| 73 | S&F in repairs bib tap cast copper alloy chromium plated butterfly handle screwed down screwed for iron pipe completed (15mm dia tap). |
| 74 | S & F in repairs 15 mm bore pillar taps, fancy type Cast Copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe. |
| 75 | S&F in repairs Angle stope valves, cast copper alloy, screwed down high pressure with crutch or butter fly handle, fancy type, chromium plated with long shank and cup (concealed type), 15mm bore dia of pipe. complete all as directed by Engr-in-charge. |
| 76 | S&F in repairs 75 mm dia PVC (SWR) floor trap plain with greting incl jointing with solvent cement |
| 77 | Demolition and breaking up drain pipes (Salt glazed ware /PVC/ AC or Reinforced concrete) set in cement mortar (75/110mm dia) |
| 78 | S&F 75 mm bore PVC (SWR) pipes of single socketed in any length with rubber ring joints laid in trenches or in floors all as specified |
| 79 | S&F 75 mm bore PVC (SWR) pipes of single socketed in any length with rubber ring joints fixed to wall including necessary MS flat Iron clamps of size (40 x 4mm) all as specified and as directed by the Engineer - in - Charge. |
| 80 | S&F 75 mm bore. PVC (SWR) bends |
| 81 | S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches |
| 82 | S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including necessary MS flat Iron clamps of size (40 x 4mm) all as specified and as directed by the Engineer - in - Charge. |
| 83 | S&F 110 mm PVC (SWR) bend any radius |
| 84 | S&F 110mm bore.PVC(SWR) junction single (single T) equal or unequal with access door |
| 85 | Demolition or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facings dressed stonework and precast concrete articles all as specified and directed. |
| 86 | M & L Pre-cast cement concrete type C1 1:3:6 (20mm graded aggregate) block masonry with solid blocks, exc 10cm in width and setting in in cement mortar 1:6 all as specified and directed. |
| 87 | M & L walling of random rubble, uncoursed, well bonded, bedded and solidly hearted built in CM 1:4 all as specified and directed. |
| 88 | M & L PCC B1 1:2:4 (12.5mm graded aggregate)for in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed |
| 89 | M&L PCC (1:4:8) D-2, using 40mm graded stone aggregate in foundation, filling and mass concrete. |
| 90 | S &F Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof (75mm dia) |
| 91 | S &F Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof (100mm dia) |
| 92 | Earth work in excavation by mechanical means (Hydraulic excavator)/in all kind of soil for foundation trenches or drains (not exceeding 1.5 m in width or 10 Sqm on plan),including dressing of sides and ramming of bottoms,lift upto 1.5m,including getting out the excavated soil and disposal of surplus excavated soil as directed,within a lead of 50 m complete all as specified and as directed |
| 93 | S&F for factory made cement concrete RCC manhole cover (900mm X 450mm X 50mm) all as specified and directed by E-in-Charge |
| 94 | Supplying, fixing, jointing and testing reinforced concrete drain pipes 150 mm bore, class NP2, laid and jointed with collar in C M 1:1 complete all as specified and directed. |
| 95 | M & L for concrete bed to drain pipes in PCC 1:3:6 type D-2 (using 40 mm graded stone aggregates) including packing under and hauching against the side of the pipes after they are laid tested for pipes of 150 mm bore dia complete all as specified and directed. |
| 96 | Returning, filling in the any type of soil including spreading, levelling. Watering and well ramming in layers not exceeding 25cm thick each layer complete all as specified and directed. |
| 97 | On site LDPE conventional septic tank 25 Users size (3.5 x1.5x 1.5mtr)designed to carry sewage and sullage water, excavation in any type of soil, below foundation in 150mm thick Hard core, 150mm thick PCC 1:3:6, Vent shaft, connection etc., complete with effective depth of 1.5 m and overall depth of 3m including returning and filling and all as specified and directed by E-in-Charge. |
| 98 | M&L for applying two coats of smart care crack seal, with open and widen the cracks in a 'V' shaped groove and provide a strong base for adhesive of crack seal to the surface wire brush and clean the area throughly with water to free it from dust and loose particles any algal/fungal growth must be cleaned using bio-wash such as bleaching powder and as directed by Engineer-in-Charge |
| 99 | M&L for applying two coats of Damp proof (Acrylic water proof) of fiber reinforced elastomeric liquid on filling of crack seal applied portion on both sides of cracks each side 75mm wide as directed by Engineer -in-Charge. |
| 100 | Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings all as specified and directed. |
| 101 | Dismantling wrought iron or mild steel work of any description not otherwise provided for all as specified and directed. |
| 102 | Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets all as specified and directed. |
| 103 | Material and labour for suspended false ceiling using anodized aluminum snap grid frame work. Including Hanger 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G I flat 40x3mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete all as specified and directed. |
| 104 | M & L Elegant Tile made of perforated cement fiber composite 595x595/295X1195/595X1195x5mm covered with absorptive microfiber coating on the front side and Acoustics fiber on the back side, water resistance, fire resistant absorption coefficient upto 0.89 at 160 Hz tested as per ISO 354. The tiles are anti-sag and installed on T24 grid system of 0.6mm thick Main 'T' length minimum 3000mm, web minimum 35mm to be placed at 600mm center to center and secondary cross 'T' of length 600mm web minimum 35mm inter locked, Wire Support for Main T to be taken at every 1200mm length wise and 600mm width wise, with a backing of 50mm 1000 GSM thick absorb wool tested as per Fire Retardant IS 15061-2002 for excellent results. |
| 105 | S&F MS Rolled sections in main and cross beams,hip and jack rafters ;purlins where connected to common rafters running rails and guids for sliding doors ;fixed with angle cleats or other connecting plates and similar work confirming to Fe-290, Gde-E-165 complete all as specified and as directed. |
| 106 | S&F MS Wind ties for roof including securing bolts, posts & struts including cutting tops to shapes as directed,including all necessary drilling,bolting or reveting etc and similar work confirming to Fe-290, Gde-E-165 complete all as specified and as directed. |
| 107 | S&F Pre- painted galvalume aluminium zinc coating GI based seme corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall ,fixe with self tapping screws and all as specified and as directed. |
| 108 | S&F Pre- painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall ,fixe with self tapping screws and all as specified and as directed. |
| 109 | Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out Hard/dense soil all as specified and directed. |
| 110 | M & L for 75 mm thick PCC 1:4:8 type D-2 using 20mm graded aggregate as sub flooring all as specified and directed. |
| 111 | Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc.,of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand all as specified and as directed. |
| 112 | Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. |
| 113 | Taking down the sub main wiring of any dia / sq mm on teak wood batten / PVC conduit GI earth wire all as directed. |
| 114 | Taking down cearfully by unscrewing the unserviceable DB Boxes, MCB distribution boards SP & TPN with porcelain cutouts etc all as directed. |
| 115 | Material and labour for providing point wiring with two runs of 1.5 Sqmm multi stranded copper conductor FRLSH PVC insulated single core 1100 volts grade & with one run of 1.5 Sqmm single core multi stranded copper conductor Flame retardant PVC insulated 1100 Volts grade wire for continuous earthing complete in and including PVC casing and caping with all fittings/fixture etc and open recessed type Plastic Enclosure ( Plastic Switch Board ) ISI Marked (IS:14772) for housing switches / sockets all a specified and directed |
| 116 | One light/ Exhaust/Wall mounted /Ceiling, Bell point controlled by one regulator/switch controlled by one switch . |
| 117 | One 3 pin socket 5 A on independent board. |
| 118 | One 3 pin socket 5 A on same board. |
| 119 | Material and labour for providing point wiring with two runs of 2.5 Sqmm multi stranded copper conductor FRLSH PVC insulated single core 1100 volts grade & with one run of 1.5 Sqmm single core copper stranded FRLSH PVC insulated 1100 volts grade wire for continuous earthing complete in and including PVC casing and caping, ISI Marked complet for housing one 15 A Switch / sockets complete Note : Metal sunken box , cover plate and frame etc will be measured and paid seprately in respective item. |
| 120 | M&L for wiring comolete with 1.5 sq mm single core multistranded copper conductor FRLSH PVC insulated and unsheathed cable 1100 V grade conforming to IS 694 drawn through steel ERW conduit flame proof, heavy grade ISI marked including nessay conduit accessories surface on wall, ceiling etc including 1.5 sq mm PVC insulated flame retardent copper conductor as in continous earth wire for one FLP light/fan point controlled one way metal clad switch of 5 Amps capacity complete all as specified & directed. |
| 121 | M&L for wiring comolete with 2.5 sq mm single core multistranded copper conductor FRLSH PVC insulated and unsheathed cable 1100 V grade conforming to IS 694 drawn through steel ERW conduit flame proof, heavy grade ISI marked including nessay conduit accessories surface on wall, ceiling etc including 2.5 sq mm PVC insulated flame retardent copper conductor as in continous earth wire for one 3 pin socket 16 A on independent board complete all as specified & directed. |
| 122 | S&F Flame proof switch socket & plg combined in LM6 cable terminaton box in LM6 16A 250V 2P+earth |
| 123 | S&F Switch flame proof rotary type with termination box in LM6 , 16A single pole 250 V complet all as specified & directed. |
| 124 | S & F Sub Main Wiring with FRLSH PVC Insulated multistranded copper conductor wires of size 2x6.0 sq. mm + 1x6.0 sq. mm earth wire in casing caping complete as directed. |
| 125 | S & F Sub Main Wiring with FRLS PVC Insulated multistranded copper conductor wires of size 2x4.0 sq. mm + 1x2.5.0 sq. mm earth wire in casing caping complete as directed.Note : for Item No 10 & 11 One run of phase wire one run of Neutral wire and one run of Earth wire and one run of casing and capping shall be meassured and as one length. |
| 126 | Supply and fix sheet metal enclosure MCB DB double door SPN 8 way 230 V with neutral link and with 200 A bus bar including fixing concealed in wall including cutting chasing in stone masonary / Brick masonary and making good the disturbed surface making all nacessary incomming and out going connections using proper size copper thimbles complete all as required on site all as directed |
| 127 | Supply and fix sheet metal enclosure MCB DB double door SPN 4 way 230 V with neutral link and with 200 A bus bar including fixing concealed in wall including cutting chasing in stone masonary / Brick masonary and making good the disturbed surface making all nacessary incomming and out going connections using proper size copper thimbles complete all as required on site all as directed |
| 128 | S&F MCB SPN 40 to 63 Amp 10 kA 240 Volt, 'C' Curve and electric connections with copper thimbles complete all as specified and directed by Engr-in-Charge. |
| 129 | S&F MCB SP 240 volt 6 to 32 A 'C' series complete |
| 130 | Supply and fix switch piano flush type 6 Amp one way. (ISI marked) |
| 131 | Supply and fix switch piano flush type 16 Amp one way. (ISI marked) |
| 132 | Supply and fix Socket out let , 3 pin 5 Amp (ISI marked) |
| 133 | Supply and fix switch socket combination 5 / 16 A, 2 in 1, 5 Pin, flush type.(ISI marked) |
| 134 | Supply and fix Piano switch bell push type switch 5 A.(ISI marked) |
| 135 | Supply and fix bell electric 230V single pole complete as directed. |
| 136 | S/F Fan Regulator electronic step type 100 W complete as directed (ISI marked) |
| 137 | Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete |
| 138 | S&F LED light fitting 1x20 w flame proof, CMRI certified recommended for gas vapour groop of IIA & IIIA |
| 139 | Supply and fix high quality indoor Surface and wall mounted batten suitable for 20 Watt Aluminum T8 Tube rod 4 feet long , including LED retrofit Tube rod 20 Watt Aluminum T8 Tube rod 4 feet long 6000K colour temperature, having lumen output not less than 100 Lumen per watt & integrated electronic driver with industrial grade heavy duty driver having THD<10%. complete with all accessories internally pre-wired and including connecting up with three core 0.5 Sqmm flexible copper conductor cable ceiling rose to fitting terminal. |
| 140 | Disconneting & taking down ceiling fan of 1200 mm sweep / exhaust fan up to 450 mm sweep/Wall mounted fan up to 400 mm sweep for servicing, strip opening of fan including servicing, rewinding and greasing complete at site. Re-assembling and refixing to the same/other location after replacing rubber reel, fixing bolts and nuts with lock pins, connectors for complete fan including writing MES No all as required and directed by Engineer-in Charge. Testing complete after servicing and fixing for smooth and noise free operation. |
| 141 | Taking down the existing street light fitting and Supply & fix (in Repalcement) energy saving and environmental friendly long life LED Street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with impact and corrosion resistant including thermal management in multiple optics IP 65/IP66 road way luminaries with LEDs as light source and lens embedded PC cover /toughened glass and impact resistance of IK07 and electronic driver fixed on pole/wall with and including suitable dia size bracket as per manufacturer recommendation, bracket complete with MS flat iron clamps (clamp shall be 40x5 mm MS flat), nuts and bolts and washers painting the clamps with coat of aluminium paint over a coat of red oxide primer including connection complete all as specified. |
| 142 | M&L earthing complete with galvanised steel earth plate eletrode 60 cm x 60 cm and 6mm thick buried directly in ground earth pit not less than 2.25mtr deep below normal ground level with top prjgc, of the plate not less than 1.5m below normal ground level, connected to the Galvanise Iron earth lead 32 mm x 6 mm (GI Strip) size, by means of bolts, nuts, check buts and washers of galvanised iron and 32 mm x 6 mm earth lead protected by provision of GI medium grade pipe 40 mm bore including provision of aggregates with 40 mm thick cover of RCC (1:2:4) , reinforced with XPM (weight not less than 4 kg per sqmm) and frame of angle iron 40mmx40mmx3mm and with 6 mm dia MS bar handle made to shape, GI light grade 20mm bore pipe of suitable length for watering perforated at bottom placed on top edged of earth plate, common salt and charcoal filling, funnel, wire mesh and earth work in hard/dense soil, returning filling in distance not exceeding 50 mtr and removal of surplas soil to plate No 3 of SSR 2009 Part-I and connecting to feeder pillers and Transformer all as specified including testing on completion complete all as specified and directed. |
| 143 | Supply install, test and commissioning LT wall mounted indoor Panel board factory fabricated made out of 2 mm thick CRCA sheet & suitable size to accomodate all accessories/fittings, compartmentalized in construction to accommodate incoming and outgoing MCCB, MCB and TPN copper bus bars of rating not less 1.5 times the rated cap of incomer MCCB. The TPN bus bars shall be insulated with colour coded heat shrinkable sleeve and shall be mounted on DMC/epoxy insulator. The incoming as well as outgoing MCCBs/MCBs shall have copper extension links of current carrying cap not less than 1.5 times the rated capacity of individual feeders. A detachable predrilled gland plate of thickness not less than 2 mm thick should be used at the bottom for entry of armoured cable of adequate size with glands.The above panel shall be front openable lockable /openable by key, Provn shall be made to visible/read meter reding at front side of the door. The Panel shall be manucatured from CPRI approved manufacturer of makes stipulated. The cost is inclusive of disconnecting existing cables, reconnecting the cables with lugs & glands, making good of distribued PCC all as directed, including following acessories(a) Incoming MCCB FP 415 Volt 100 Amps 25 kA - 01 Nos(b) Outgoing MCCB FP 63 Amps, 10 kA - 02 Nos(c) Outgoing MCB SPN Amps, 230 Volts , 10 kA - 05 Nos Please Enable Macros to View BoQ information |
| 144 | Supply install, test and commissioning LT wall mounted indoor Panel board factory fabricated made out of 2 mm thick CRCA sheet & suitable size to accomodate all accessories/fittings, compartmentalized in construction to accommodate incoming and outgoing MCCB, MCB and TPN copper bus bars of rating not less 1.5 times the rated cap of incomer MCCB. The TPN bus bars shall be insulated with colour coded heat shrinkable sleeve and shall be mounted on DMC/epoxy insulator. The incoming as well as outgoing MCCBs/MCBs shall have copper extension links of current carrying cap not less than 1.5 times the rated capacity of individual feeders. A detachable predrilled gland plate of thickness not less than 2 mm thick should be used at the bottom for entry of armoured cable of adequate size with glands.The above panel shall be front openable lockable /openable by key, Provn shall be made to visible/read meter reding at front side of the door. The Panel shall be manucatured from CPRI approved manufacturer of makes stipulated. The cost is inclusive of disconnecting existing cables, reconnecting the cables with lugs & glands, making good of distribued PCC all as directed, including following acessories(a) Incoming MCCB FP 415 Volt 100 Amps 25 kA - 01 Nos(b) Outgoing MCCB FP 63 Amps, 10 kA - 02 Nos(c) Outgoing MCB SPN Amps, 230 Volts , 10 kA - 05 Nos Please Enable Macros to View BoQ information |
