|
| 1 | Supplying only Chlorpyriphos/Lindane emulsifiable concentrate of 20% chemical emulsion in sealed containers including delivery as specifies. |
| 2 | Diluting and injecting chemical emulsion for Post-Constructional anti-termite treatment of soil under existing floors using chemical emulsion With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1:2 (1 cement : 2 Coarse sand) to match the existing floor complete all as specified and as directed. Note : Chemical Emulsion will be measured and paid seperately under serial item No.1 |
| 3 | Diluting and injecting chemical emulsion for Post-Constructional anti-termite treatment at points of contact of wood work by chemical emulsion Chlorpyriphos/ Lindane (in oil or kerosene based solution) @ 0.5 litres per hole by drilling 6 mm dia holes at downward angle of 45 degree at 150 mm centre to centre and sealing the same complete all as specified and as directed.Note : Chemical Emulsion will be measured and paid seperately under serial item No.1 |
| 4 | Diluting and injecting chemical emulsion for Post-Constructional anti-termite treatment Along the external wall below concrete or masonry apron using chemical emulsion With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration @ 2.25 litres per linear metre including drilling and plugging holes etc complete all as specified and as directed. Note : Chemical Emulsion will be measured and paid seperately under serial item No.1 |
| 5 | Dismantling doors, windows and clerestory windows (steel or wood) of area not exceeding 3.00 Sqm shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead complete all as specified and as directed |
| 6 | Supply and fixing Pressed steel frames of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., including filling of PCC 1:3:6 inside the frame, and two coats of painting external complete, all as specified and as directed |
| 7 | Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge. |
| 8 | Supply and fixing glazing (with float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) in aluminium door, window, ventilator shutters and partitions etc with EPDM rubber / neoprene gasket etc complete as per the architectural drawings and the directions of Enginer-in-charge. |
| 9 | Supply and fixing powder coated aluminium work for fixed portion of doors, windows, ventilators and partitions with extruded built up standard tubular sections /appropriate Z sections and other sections of approved make conforming to IS : 733 and IS : 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions i.e at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium section shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling CP brass / stainless steel screws, all complete as per architectural drawings and the directions of Engr -in- Charge. (Glazing, paneling and dash fasteners to be paid for separately) (minimum thickness of powder coating 50 micron). |
| 10 | Supply and fixing powder coated aluminium work for shutters of doors, windows (sliding) & ventilators and partitions with extruded built up standard tubular sections /appropriate Z sections and other sections of approved make conforming to IS : 733 and IS : 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions i.e at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium section shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling CP brass / stainless steel screws, including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required all complete as per architectural drawings and the directions of Engr -in- Charge. (Fittings, Glazing, paneling and dash fasteners to be paid for separately) (minimum thickness of powder coating 50 micron). |
| 11 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster includng disposal of rubbish to the dumping ground within 50 metre lead |
| 12 | Material & labour for rendering 15mm thick in fair faces of brick work or concrete surfaces in CM 1:4 finished even and smooth in fine sand complete all as specified. |
| 13 | Material & labour for rendering 12 mm thick in fair faces of brick work or concrete surfaces in CM 1:6 finished even and smooth in fine sand complete all as specified. |
| 14 | Material & labour for distempering with 1st quality premium acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour with two coats on new work including water thinable priming coat with cement primer complete, as per manufacturer's specification over including 2mm thick internal wall care putty finish . |
| 15 | Material & Labour for finishing the newly plastered wall by applying Two coats 100 % premium acrylic emulsion paint @ 1.67 litre/ 10 Sqm having VOC less than 50 gm/ litre and UV resistance as per IS 15489 : 2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade ( Company Depot tinted ) with silicon additives over and including priming coat of exterior primer applied @ 0.90 litre / 10 Sqm complete all as specified and directed by Engr-in-charge. |
| 16 | Demolishing cement concrete Nominal concrete or leaner mix (i/c equivalent design mix) manually / by mechanical means including disposal of materials within 50 metres as per direction of Engr -in- Charge |
| 17 | M&L PCC with 1:2:4 of using 20mm graded aggregate laid as levelling course complete all as specified and directed. |
| 18 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. |
| 19 | Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of anysize as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick rendering of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. |
| 20 | Providing and laying vitrified tiles in different sizes ( size of tiles 600 x 600 mm) ( thickness to be specified by manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours & , over 20mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 Kg / Sqm including grouting the joint with white cement & matching pigments etc complete Please Enable Macros to View BoQ information |
