|
| 1 | Roofing |
| 2 | 15.28.2:Dismantling roofing including ridges, hips, velleys and gutters etc., and stacking the material within 50 metres lead of :Asbestos cement Sheet |
| 3 | 12.8:Providing reinforced by organic fibres and/or inorganic synthetic fibres cement6 mm thick corrugated sheets (as per IS: 14871) roofing up to any pitch andfixing with polymer coated J, or L hooks, bolts and nuts 8 mm dia. G.I. plain andbitumen washers or with self drilling fastener and EPDM washers etc. complete(excluding the cost of purlins, rafters and trusses), including cutting sheets tosize and shape wherever required. |
| 4 | 12.12.4:Providing and fixing ridges and hips in fibre cement reinforced by organic fibres and/or inorganic synthetic fibres roofing with suitable fixing accessories or self drilling fastener and EPDM washer etc. complete.Unserrated adjustable hips |
| 5 | 13.52.1:Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work |
| 6 | OD2979/2025-2026:Dismantling existing old CR rolling shutters dismembering and stacking within 50 metres lead as per directions of Engineer -in-Charge. |
| 7 | OD2970/2025-2026:Supplying and fixing rolling shutters of approved make, made of required size GI. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing andfixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and top cover of required thickness for rolling shutters. 19 guage flat GI white colour powder coated shutter with .35 GI sheet top cover (based 10.6.2) |
| 8 | 10.8.1:Extra for providing mechanical device chain and crank operation for operating rolling shuttersExceeding 10.00 sqm and upto 16.80 sqm in the area |
| 9 | 10.7:Providing and fixing ball bearing for rolling shutters. |
| 10 | OD2974/2025-2026:OD -Providing and fixing single scaffolding system (cup lock type) on the exterior side, upto seven story hight made with 40 mm dia. M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staricase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after. The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required location with essential safety features for the workmen etc. complete as per directions and approval of Engineer- in Charge. The elevational area of the scaffolding shall be measured for payment purpose. The payment will be made once irrespective of duration of scaffolding. Note:- This item to be used for maintenance work judicially, necessary deduction for scaffolding in the existing item to be done .(Based on 14.72) |
| 11 | OD3242/2025-2026:Steel work using hot dip galvanized angles, Tees and channels in trusses etc., with a galvanizingthickness not less than 85 microns, including cutting, hoisting, welding, fixing in position and applying a priming coat of approved steel primer, etc. complete.( Based on TS No.211/2021-2022/CE Dated:15-10-2021 ) |
| 12 | OD3243/2025-2026::Steel work for purlin/single section with hot dipped galvanized steel tubes includingcutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete with a minimum galvanizing thickness not less than 85 micrones.(Based on TS No.211/2021-2022/CE Dated:15-10-2021 ) Please Enable Macros to View BoQ information |
