|
| 1 | M&L for 20mm thick sand filling under floor or in foundations including watering and consolidation complete all as specified and directed. |
| 2 | M&L for broken stone or boulders hardcore of gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and directed. |
| 3 | M&L for providing precast cement concrete louvres and jallies 35 mm thick (measured solid) including all mouldings but excluding frame in cement concrete 1:2:4 type B0 using 12.5 mm graded stone aggregates and set in cement mortar 1:4 complete all as specified and directed. |
| 4 | M&L for chipping of plaster / unsound weak and cracked concrete / cover of reinforcement of RCC member like slab, beam, column, chhaja etc or as per site requirement by standard power driven percussion type or pneumatic chisel including tapering all edges, making square shoulder of cavities etc and disposal of debris / malwa from site complete all as specified and directed. |
| 5 | M&L for cleaning of existing reinforcement with wire brush/rotary wire brush to make surface free from rust scales, loose material, dirt etc. complete and applying two coats of alkline rust converting primer on the existing rebar and allowing it to react with rust for 6 hours and form corrosion resistant, insoluable and adherant protective layer, including cleaning the reinforcement wire brushing to remove the rust spalls, with time interval of 1 hour between the coats complete all as specified and directed. |
| 6 | M&L for corrosion inhibiting impregnation coating, designed for use as an imregnation for protection of steel reinforcement within unexposed concrete with in consumption of 0.5 Kg/Sqm. The product should be amino alcohol and inorganic combination based migratroy corrosion inhibitor for both cathodic and anodic protection complete all as specified and directed.Make : Fosroc / Thermax / Sika or equivalent as approved by GE. |
| 7 | M&L for zinc rich epoxy anti-corrosive protective coating for rebar corrosion protection system complete all as specified and directed.Make : Fosroc / Thermax / Sika or equivalent as approved by GE. |
| 8 | M&L for providing, mixing & applying two component of epoxy resin concrete bonding coat on prepared RCC surfaces as per manufacturer specification including prepartion of surface by chipping and throughly cleaning of surface complete wherever required complete all as specified and directed. Make : Fosroc / Thermax / Sika or equivalent as approved by GE. |
| 9 | M&L for re-building the section of damaged RCC elements to its original size on an average 15 mm thickness in two layers each by providing and applying with pre- batched, polymer modified mortar of approved make having compressive strength not less than 50 N/sqmm (28 days) as per ASTM C-109 and flexural strength not less than 05 N/sqmm (7 days) as per ASTM C-293-79 standards including water fog curing to keep surface moist for seven days complete all as specified and directed. Make : Fosroc / Thermax / Sika / Dr. fixed or equivalent make as approved by GE.Note : (i) To achieve the required thickness, the above process should be repeated after 24 hours.(ii) Surface area with 15mm thick layer will be measured as one unit for payment purpose.(iii) Rate shall be including all necessary scaffolding upto height of four storey building. |
| 10 | M&L brick work using old size sub class 'B' bricks straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed. |
| 11 | M&L 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms or any horizontal portion and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified & directed. |
| 12 | M&L 20 mm thick granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall) 12mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and including rendering 10 mm thick in CM 1:4 complete all as specified and directed. |
| 13 | M&L for EPDM (Ethylene Propylene Diene Monomer) rubber strip of width 2 cm suitable of 1 mm to 2 mm gap,fixed with adhessive like Fevicol pasting along with blue tag type nails complete all as specified and directed. |
| 14 | M&L for Neoprene / EPDM (Ethylene Propylene Diene Monomer) rubber gasket complete all as specified and directed. |
| 15 | Taking down chowkats or frames n.exc 1.5 Sqm each with shutters (without taking off shutters from the frames) including making good of disturbed portion except space for holdfast complete all as specified and directed. |
| 16 | Taking down chowkats or frames exc. 1.5 sqm but n.exc 4.0 Sqm each with shutters (without taking off shutters from the frames) including making good of disturbed portion except space for holdfast complete all as specified and directed. |
| 17 | S&F second class hard wood 35 mm thick glazed and skeleton shutters, open rebated and prepared to receive glass , gauze etc with out sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutters as specified in SSR part I section 8 clause 8.24 (a) complete all as specified and directed. |
| 18 | S&F 35 mm thick second class hard wood rail and style plain framed factory made panelled shutter (two panel) with lock rail and panel of 9 mm BWP commerical ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (part-I), kiln seasoned and chemically pressure treated complete all as specified and directed. |
| 19 | S&F 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed. |
| 20 | S&F factory made solid panel PVC door shutter 30 mm thick style consisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC “C” channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, S & F in the frame as shown on drawing in section 8 of SSR-2020 Part-II complete all as specified and directed. |
| 21 | S&F for solid PVC door frame of size 50 x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, supplied and fixing in opening as specified and shown on drawing made on section 8 of SSR 2020 Part-II complete all as specified and directed. |
| 22 | S&F Solid PVC wall Lining consisting of 5 mm thick plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as specified and directed. |
| 23 | S&F Butt hinges extruded brass with galvanised mild steel hinge pin bright polished and fixed of size 100 mm long complete all as specified and directed. |
| 24 | S&F in repair 25 mm dia stainless steel, wood finish, fancy type, anti-rust curtain rod with curtain bracket with finials etc. for doors / windows fixed by self screw in wall complete as all specified and directed. |
| 25 | S&F aluminium, anodised, barrel tower bolts of extruded section 150 mm long complete all as specified and directed. |
| 26 | S&F in repair aluminium, anodised, barrel tower bolts of extruded section 150 mm long complete all as specified and directed. |
| 27 | S&F aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy of 300 mm length of bolt complete all as specified and directed. |
| 28 | S&F in repair aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy of 300 mm length of bolt complete all as specified and directed. |
| 29 | S&F aluminium handles cast type anodised of 150 mm size complete all as specified and directed. |
| 30 | S&F in repair aluminium handles cast type anodised of 150 mm size complete all as specified and directed. |
| 31 | S&F Mortice lock, vertical type, size 100 mm, 4- lever brass body with two keys complete all as specified and directed. |
| 32 | S&F in repair mortice lock, vertical type, size 100 mm, 4- lever mild steel body with two keys complete all as specified and directed. |
| 33 | S&F brass CP tubular towel rail, 20mm dia, 60cm long between flanges etc. complete as all specified and directed.Make : Jaquar CAT Part No AKP-CHR-35711PS / Kohler CAT Part No K-5630IN-CP / Grohe CAT Part No 40366EN1 or equivalent make as approved by GE. |
| 34 | S&F in repair door closer hydraulically regulated designation No 3, universal type, suitable for door shutter of weight between 61 to 80 Kg of aluminium (extruded section) body complete all as specified and directed. |
| 35 | S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed. |
| 36 | S&F in repair stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples including removing MS screws and welding if required over steel window and removing aluminium clips / PVC beads in aluminium window and UPVC window complete all as specified and as directed. |
| 37 | S&F in repair double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass,other parts made of mild steel heavy duty and fixed complete all as specified and directed. |
| 38 | S&F mild steel framed work for windows grills such as grills, gratings etc with ends of bars shouldered and / or riveted or forged into spikes, framed guard bars, barred iron doors / window and similar work conforming to Fe -290 Gde E-165 complete all as specified and directed. |
| 39 | S&F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete all as specified and directed. |
| 40 | S&F steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay complete with glazing bars, dovetailed or welded complete all as specified and directed. |
| 41 | S&F steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay complete with out glazing bars, dovetailed or welded complete all as specified and directed. |
| 42 | S&F steel ventilator with top hung shutter including hinges steel peg stay complete all as specified and directed |
| 43 | M&L for powder coated (minimum thickness of powder coating 50 micron) anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed. |
| 44 | S&F powder coated (thickness of powder coating not less than 50 micron) anodised aluminium window and ventilator shutters, side hung / sliding type without sash bars, aluminium sections weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws anodised aluminium fittings such as peg stays 150 mm long (1 No), hinges type B-21, 100 mm long (2 No) , suitable handle (1 No) complete all as specified and directed. |
| 45 | M&L false ceiling at all heights with semi perforated 12 mm thick micro tegular edged GRG (Glass fibre Reinforced Gypsum) false ceiling tiles of Size 595 x 595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Noncombustible as per BS 4 76 (part 4 )-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter locking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main T runners of size 15 x 32 mm of length 3000mm,cross-T of size 15x 32mm of length 1200mm and secondary intermediate cross-T of size 15 x 32 mm of length 600mm to form grid module of size 600x 600mm , suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1000mm length and L shape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 24x 4x0.40mm of length 3000 mm to be fixed on periphery wall I partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall wood screws. The work shall be carried out as per specifications, and direction of engineer-in-charge complete all as specified and directed. |
| 46 | Taking down existing aluminium window single leaf of area n.exc 1.5 sqm including taking down all members, sheet glass of any thickness, cleat, neoprene rubber beading and resecuring / refixing all section & tightening all joints including fixing new small cleats of suitable size, fixing L-type cleats of stainless steel to secure joints of stiles and rails wherever necessary and refixing all members, sheet glass, aluminium cleat but new neoprene rubber beading (paid under separate item) and making the door shutter serviceable, including fixing the shutter on hinges complete all as specified and directed. |
| 47 | S&F anodised aluminium powder coated (minimum thickness of powder coating 50 micron of approved colour) door shutter with frame, partly glazed with 5 mm thick tinted glass and partly panelled with 9 mm thick prelaminated particle board with both side decorative laminated including rubber bead joining cleat for fixing in position, aluminium door handle 150 mm size, aluminium barrel tower bolt 200 mm size, floor door stopper of size 200mm etc. using medium weight, aluminium section as follow :- (a) Frame (top & side) section shall of size 101.60x 44.75 x 2.4 mm (Section 14021)(b) Vertical Members of shutter section shall be of size 85.00 x 44.45 x 2.00 mm (Section No 19560).(c) Top members of shutter section shall be of size 83.50 x 44.45 x 2.00 mm (19581).(d) Lock rail (Middle member) of shutter section shall be of size 150 x 44.4 x 3.00 mm (Section No 19596)(e) Bottom Members of shutter section shall be of size 150.00 x 44.45 x 3.10 mm (Section No 19584)(f) Glazing clip for securing glass of shutters shall be of 0.80 mm thick (Section No 19370)Note:- Section given above are of Make Jindal, the contractor may use similar section of other make as mentioned in Appx 'B' of PS. |
| 48 | Supply fabricate & fix in position aluminium powder coated (minimum thickness of powder coating 50 micron of approved colour) three track window (two shutters glazed & one shutters wire gauge) with frame, glazed with 4 mm thick tinted glass and wire gauge with stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm including rubber bead joining cleat for fixing in position, concealed type lock for all three shutter, PVC roller etc all as specified below :- (a) Frame (top & side) section shall of size 92.00 x 31.75 x 1.50 mm (Section 20831)(b) Frame (bottom) section shall be of size 92.00 x 31.75 x 1.50 mm (Section No 20832).(c) Top members of shutter section shall be of size 18.00 x 40.00 x 1.55 mm (Section No 20738).(d) Shutter Interlock section shall be of size 18.00 x 40.00 x 1.55 mm (Section No 20737)(e) Bottom Members of shutter section shall be of size 18.00 x 40.00 x 1.55 mm (Section No 20736)Note:- Section given above are of Make Jindal, the contractor may use similar section of other make as mentioned in Appx 'B' of PS. |
| 49 | Taking down existing aluminium door single leaf of area exc 1.5 sqm but n.exc 4.0 sqm including taking down all members, sheet glass of any thickness, cleat, neoprene rubber beading and resecuring / refixing all section & tightening all joints including fixing new small cleats of suitable size, fixing L-type cleats of stainless steel to secure joints of stiles and rails wherever necessary and refixing all members, sheet glass, aluminium cleat but new neoprene rubber beading (paid under separate item) and making the door shutter serviceable, including fixing the shutter on hinges complete all as specified and directed. |
| 50 | M&L for applying fibre reinforced, single component, elastomeric liquid applied water proofing coating in white colour, anti-fungal, anti-algae, resistance to water and ageing, excellent UV resistant having Solar Reflective Index more than 105, with PU hybrid polymers and reinforcing acrylic fibers, elongation greater than 300% and applied in three layer complete all as follow :- (a) Preparation of surface by cleaning and removing loose particles then apply first coat of liquid water proofing after diluting as per manufacture instruction as a primer and allow the surface to dry for minimum 10 to12 hours complete all as specified and directed. (b) Apply second coat of liquid water proofing without dilution on the primed surface and allow time to dry the surface for minimum 10 to12 hours complete all as specified and directed.(c) Apply third coat of liquid water proofing without dilution over the second coat and allow minimum 48 hour complete all as specified and directed.Note : (i) Work shall be carried out by authorised applicator of manufacturer only and contractor will submit MoU with authorised applicator of manufacturer before execution of work. (ii) Material incorported in the work shall be calculated as per site requirement and full quantity of material shall be brought at site before execution of work.(iii) Necessary gurantee for 05 years shall be submitted by the contractor. Make :- Berger-HS Roof Kool & Seal, STP-Shali Urethane (R) BTD Plus, Asian - Smart care Damp Proof Ultra or equivalent make as approved by GE. |
| 51 | S&F fibre glass reinforced translucent corrugated sheeting 2 mm thick with two corrugation side lap fixed with L-type or J- type or cranked hook bolt in roof, wall etc complete all as specified and directed. |
| 52 | S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof overing/ cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 53 | S&F pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof overing/ cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 54 | M&L for 0.9 mm thick decorative laminate type-1 of surface finish, colour and pattern as approved, fixed with approved adhesive complete all as specified and directed. |
| 55 | M&L particle board,12 mm thick medium density, flat pressed,single layer type or three layer type with BWR type adhesive, fixed with screws to timber frame work complete all as specified and directed. |
| 56 | M&L for machine cut kota stone slab flooring mirror finished 20-25 mm thick (each slab not less than 0.25 sqm) over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing on treads of step and landing of stair including screed bed 20 mm thick in CM 1:6 complete all as specified and directed. |
| 57 | M&L for machine cut kota stone slab mirror finished 20-25 mm thick (each slab not less than 0.25 sqm) in riser of step ,skirting, dado and pillar over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including rendering 10 mm thick in CM 1:4 complete all as specified and directed. |
| 58 | M&L for 75 mm thick Cement concrete 1:3:6 type C-2 using 40 mm graded stone aggregate as in sub base complete all as specified and directed. |
| 59 | M&L for 100 mm thick Cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate as in sub base complete all as specified and directed. |
| 60 | M&L for surface preparation by removal of all loose particle to ensure clean, smooth and dry surface and laying 25mm thick PCC 1:2:4 type B-0, using 12.5 mm graded stone aggregate finished even & smooth without using extra cement with integral water proofing compound at rate of 03% per KG of cement of make approved by GE and curing the same as per manufacturer instruction complete all as specified and directed. |
| 61 | M&L for glazed ceramic coloured tiles in vertical surface 350x 250x 7 mm / 450X 350X 7 mm / 300x 600x7 mm / 450x 300x7 mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match surface of tiles over and including rendering 10 mm thick in CM 1:4 complete all as specified and directed. |
| 62 | M&L for non skid ceramic coloured tiles of design as approved 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles over and including screed bed 15 mm thick in CM 1:6 complete all as specified and directed. |
| 63 | M&L for non skid ceramic coloured tiles of design as approved 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 15 mm thick screed bed in CM 1:6 complete all as specified and directed. |
| 64 | M&L for non skid ceramic coloured tiles of design as approved 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in vertical surface etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed. |
| 65 | M&L for full body vitrified Ceramic tiles light shade cut out of 10mm thick (square/ rectangular) polished area of each tiles not exceeding 0.36 sqm in vertical surface such as dado / skirting / risers to steps etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 10 mm thick rendering in CM 1:4 complete all as specified and directed. |
| 66 | M&L for full body vitrified Ceramic tiles light shade 10mm thick (square/ rectangular) polished area of each tiles not exceeding 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles over and including screed bed or bedding layer 15 mm thick in CM 1:6 complete all as specified and directed. |
| 67 | S&F for rubber moulded machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigment complete all as specified and directed. |
| 68 | M&L for chequered cement concrete tiles 30 cm x 30 cm x 22 to 25 mm thick set, jointed and pointed in neat cement slurry as in floors with grey cement and pigments over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed. |
| 69 | Dismantling floor, hearth or wall tiling including cement mortar bedding etc (but not backing) and removing rubbish off the premises complete all as specified and directed. |
| 70 | M&L for rendering on fair faces of brick work or concrete surface of wall 15 mm thick in CM 1:4 and to be finished even and smooth with out using extra cement complete all as specified and directed |
| 71 | Taking down cement plaster any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed. |
| 72 | M&L for rendering 10 mm thick in CM 1:6 on fair faces of brick or concrete surface of wall and finished even and smooth with out using extra cement complete all as specified and directed. |
| 73 | M&L for rendering 05 mm thick in CM 1:3 on ceiling surface and finished even and smooth without using extra cement complete all as specified and directed. |
| 74 | M&L for preparation of new surface of wall of any description and applying two coats of oil bound distemper (OBD) over a coat of alkali-resistant priming paint over and including 1 mm thick wall putty all as specified and directed. |
| 75 | M&L for preparation of old plastered surfaces of ceiling and applying one coat of oil bound distemper complete all as specified and directed. |
| 76 | M&L for preparation of new surface of ceiling of any description and applying two coats of oil bound distemper (OBD) over a coat of chalk whiting on plastered surfaces preparatory to distempering over and including 1 mm thick wall putty all as specified and directed. |
| 77 | M&L for complete removal of existing treatment and preparation of old surface of wall of any description and applying two coats of oil bound distemper (OBD) over a coat of primer and including 1 mm thick wall putty all as specified and directed. |
| 78 | M&L for preparation of new surface of walls of any description with a coat of 1 mm thick wall putty and applying two coats of acrylic emulsion exterior grade weather proof paint over a coat of primer complete all as specified and directed.Make for Acrylic Emulsion Paint : Apex Ultima of Asian Paint / WeatherShield Max of Dulux / WeatherCoat Anti Dust of Berger or equivalent make as approved by GE.Note :- Acrylic Emulsion Paint shall be carried out as specified in clause 15.17 of SSR Part-I including all necessary arrangement such as scaffolding / working plateform for execution of work upto four storey building etc. |
| 79 | M&L for complete removal of existing treatment and preparation of old surface of wall of any description with a coat of 1 mm thick wall putty and applying two coats of acrylic emulsion exterior grade weather proof paint over a coat of primer complete all as specified and directed.Make for Acrylic Emulsion Paint : Apex Ultima of Asian Paint / WeatherShield Max of Dulux / WeatherCoat Anti Dust of Berger or equivalent make as approved by GE.Note :- Acrylic Emulsion Paint shall be carried out as specified in clause 15.17 of SSR Part-I including all necessary arrangement such as scaffolding / working plateform for execution of work upto four storey building etc. |
| 80 | S&F 3 mm thick sheet glass, ordinary quality and glazing with oil putty in square exceeding 0.5 Sqm in each pane, complete all as specified and directed. |
| 81 | S&F 3 mm thick sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane, complete all as specified and directed. |
| 82 | S&F 4.8 mm thick sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane, complete all as specified and directed. |
| 83 | S&F figured glass 3 mm thick, pin head type and glazing with oil putty in squares not exc 0.5 sqm in each pane complete all as specified and directed |
| 84 | S&F figured glass 4 mm thick, pin head type and glazing with oil putty in squares not exc 0.5 sqm in each pane complete all as specified and directed |
| 85 | Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone,concrete or brick surrounds, glazed with putty of fixed with beads complete all as specified and directed. |
| 86 | M&L for preparation of old painted surfaces of wood and wood based surfaces of any description, over 10 cm in width or girth and apply one coat of synthetic enamel paint complete all as specified and directed. |
| 87 | M&L for preparation of new or previously untreated surfaces of wood and wood based surfaces of any description, over 10 cm in width or girth and apply two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 88 | M&L for preparation of new or previously untreated surfaces of steel of any description, over 10cm in width or girth and apply two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 89 | S&F of CPVC pipes of 16 mm outer dia SDR 11 & Plain CPVC SDR 11 fittings in trenches complete all as specified. |
| 90 | S&F of CPVC pipes of 20 mm outer dia SDR 11 & Plain CPVC SDR 11 fittings in trenches complete all as specified. |
| 91 | S&F grating droom 100 mm dia of CP (with or without hole) complete all as specified and directed. |
| 92 | S&F for 15mm bore dia of pipe brass CP fancy type ,with crutch butter fly handle , wash hand basin mixer for mixing hot & cold water screwed down for iron pipe complete all as specified and directed.Make : Jaquar CAT Part No OPP-CHR-15011BPM / Kohler CAT Part No 22534IN-4-CP / Grohe CAT Part No 32851000 or equivalent as approved by GE. |
| 93 | M&L in repair for table top wash basins, of size 700 x 435 x 135mm Vitreous China, white, flat back, excluding taps, waste, chain and plug and porcelain stopper but including PVC waste pipe minimum 600 mm long suitable for 32 / 40 mm dia of outlet complete all as specified and directed. |
| 94 | S&F Urinal spreader in repair of CP fancy type any colour for fixing with 15 mm dia pipe (Minimum weight 60gms) complete all as specified and directed. |
| 95 | S&F in repair pvc cover (Lid) of PVC water tank (500/1000 litre capacity) opening as thread is complete all as specified and directed. |
| 96 | Dismantling of AC/PVC water tank and S&F rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) 500 litre capacity hoisted and fixed in position complete all as specified and directed |
| 97 | Dismantling of AC/PVC water tank and S&F rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) 1000 litre capacity hoisted and fixed in position complete all as specified and directed. |
| 98 | M&L in repair for PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors of 75 mm bore of pipe etc complete all as specified and directed. |
| 99 | M&L in repair for PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors of 110 mm bore of pipe etc complete all as specified and directed. |
| 100 | M&L in repair for PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls of 110 mm bore of pipe etc complete all as specified and directed. |
| 101 | S&F PVC (SWR) bends any radius of 75 mm bore without access door complete all as specified and directed. |
| 102 | S&F PVC (SWR) bends any radius of 110 mm bore without access door complete all as specified and directed. |
| 103 | M&L PVC (SWR) gully trap 125/110 mm setting and jointing with solvent cement complete all as specified and directed |
| 104 | Taking up or down steel tubing and connections including cleaning if refixing required for 15 mm bore of pipe complete all as specified and directed. |
| 105 | Taking up or down steel tubing and connections including cleaning if refixing required for 20 mm bore of pipe complete all as specified and directed. |
| 106 | S&F in repair bib taps cast copper alloy with crutch or butterfly handle, long body, screwed down, screwed for iron pipe or for brass ferrule fancy type chromium plated of 15 mm bore dia of pipe complete all as specified and directed. |
| 107 | S&F in repair for 15mm bore dia of pipe pillar taps cast copper alloy, with capstan head chromium plated fancy type screwed down high pressure with or without lettered 'Hot' or 'cold' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed. |
| 108 | S&F in repair for 15mm bore dia of pipe brass CP wall mixer for mixing hot & cold water screwed down for iron pipe complete all as specified and directed. |
| 109 | S&F in repair stop valves, fancy type, chromium plated, cast copper alloy, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions for 20 mm bore dia of pipe complete all as specified and directed. |
| 110 | S&F ball brass valves, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule of 20 mm bore dia of pipe complete all as specified and directed. |
| 111 | S&F in repair ball brass valves, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule of 20 mm bore dia of pipe complete all as specified and directed. |
| 112 | S&F in repair ball valves for 15 mm bore dia of pipe high pressure of PTMT with Epoxy coated aluminium rod and high density plastic ball screwed for iron pipe (minimum weight 142 gms) complete all as specified and directed. |
| 113 | S&F in repair ball valves for 20 mm bore dia of pipe high pressure of PTMT with Epoxy coated aluminium rod and high density plastic ball screwed for iron pipe (minimum weight 210 gms) complete all as specified and directed. |
| 114 | S&F PVC connection 15 mm size bore with PTMT nuts of length 450 mm complete all as specified and directed. |
| 115 | M&L for cement concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid & tested for 100 mm bore of pipe with cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate complete all as specified and directed. |
| 116 | M&L in repair toilet paper holder of brass, chromium plated fixed to walls with chromium plated (CP) brass screws complete all as specified and directed. |
| 117 | S&F in repair sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes, including fixing cantilever brackets and connecting union to pipe, overall size 915 mm x 460 mm, bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed. |
| 118 | M&L in repair wash down water closet vitreous china white pedestal pattern with 'P' or 'S' trap including connecting to outgoing drain pipe & to flushing pipe also including plastic water closet seat, black/white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, excluding flushing cistern and flush pipe complete all as specified and directed. |
| 119 | S&F in repair Water closet vitreous china squatting pan, orissa pattern 580x440mm white with integral foot rests (excluding flushing cistern and flush pipe) and including provision of lime concrete bedding ,'P' or 'S' trap 100 mm bore , flushing pipe ,anti-syphonage pipe and connection etc and making good to floor complete all as specified and directed. |
| 120 | M&L in repair for Vitreous china urinal half stall type white (excluding flushing cistern flush pipe and waste pipe) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement etc complete all as sapecified and directed. |
| 121 | S&F in repair PVC 10 litres capacity valveless ,syphonic action type low level flushing cistern ,white including flush pipe, inlet, ball valve, float and handle etc complete all as specified and directed. |
| 122 | M&L in repair for vitreous china wash basin, white,flat back, size 550 x 400 mm with pedestal, brackets, including PVC connection of 450 mm long, PVC (HDPE) 32 mm bore waste pipe, brass couplings 32 mm CP etc. complete all as specified and directed.Make:- Jaquar Cat part No. KUS-WHT-35935 / Grohe Cat Part No. 39231000 / Kohler cat Part No. 25816IN-0 or equivalent make as approved by GE. |
| 123 | S&F in repair looking mirror 5.5 mm thick of selected quality glass of size 600 x 450 mm bevelled edge , mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plug with chromium plated brass screw and cup washers including aluminium anodized frame complete all as specified and directed. |
| 124 | S&F in repair Sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed. |
| 125 | S&F in repair for 32 mm bore brass chromium plated bottle trap for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified and directed.Make:- Jaquar Cat part No. ALD-CHR-769L300x190 / Grohe Cat Part No. 28920000 / Kohler cat Part No. K-9033-CP or equivalent as approved by GE. |
| 126 | S&F in repair bib taps 2-in-1 cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule fancy type of 15 mm bore dia of pipe complete all as specified and directed. Make : Jaquar CAT Part No KUP-CHR-35041PM / Kohler CAT Part No 25432IN-4-CP / Grohe CAT Part No 20281000 or equivalent as approved by GE. |
| 127 | S&F in repair for single piece WC With UF Soft Close Slim Seat Cover, Hinges, Flush Cistern Fitting, fixing accessories S / P Trap as per manufacturer instructions complete all as specified and as directed. Make : Jaquar CAT Part No LYS-WHT-38851S300UFSMN / Hindware Cat Part No. 92565 (S-22) / Cera Cat Part No. S1013123 or equivalent as approved by GE. |
| 128 | S&F in repair angle stop valve, fancy type chromium plated cast copper alloy, for 15 mm bore dia of pipe screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union complete all as specified and directed. Make:- Jaquar CAT Part No OPP-CHR-15053PM / Kholer CAT part No. 11568IN-7B-CP / Grohe CAT Part No 2201600M or equivalent as approved by GE. |
| 129 | S&F in repair brass chromium plated overhead shower rose of 120 X 120 mm / 150 x 150 mm size with or without swivel joint complete all as specified and directed. Make : Jaquar CAT Part No OHS-CHR-1667 / Grohe Cat Part No. 26565000 / Kohler cat Part No. 22645IN-CP or equivalent as approved by GE. |
| 130 | S&F in repair health faucet (hand shower) chromium plated suitable for 15 mm dia pipe with 1.2 metre long flexible tube with non return valve and wall hook including making connections and fixed in position complete all as specified and directed.Make : Jaquar CAT Part No ALD-CHR-577 / Kholer CAT Part No K-12927IN-CP / Roca CAT Part No RF9060A1 or equivalent make as approved by GE. |
| 131 | S&F in repair for 15mm bore dia of pipe, brass CP, wall mounted basin mixer (with minimum weight 1.2 Kg) for mixing hot & cold water screwed down for iron pipe complete all as specified and directed.Make : Jaquar CAT Part No QQP-SSF-7433PM / Kohler CAT Part No 5681IN-4ND-CP / Grohe CAT Part No 19571002 or equivalent make as approved by GE. |
| 132 | S&F in repair float corner glass shelve 8 mm thick 250 mm radius complete all as specified and directed.Make:- Jaquar CAT Part No. ACN-CHR-1173 or equivalent model of make Grohe / Kohler / Roca as approved by GE. |
| 133 | S&F in repair concealed Stop Valve with adjustable wall flange, fancy type chromium plated cast copper alloy, for 15 mm bore dia of pipe screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union complete all as specified and directed. Make:- Jaquar CAT Part No VGP-CHR-81083K / Kholer CAT part No. K-16087IN-4-CP / Roca CAT Part No RT5A1509CAH or equivalent as approved by GE. |
| 134 | S&F in repair CP Stainless Steel Wall Mounted Square Soap Dish / Soap Stand / Soap Holder, approximate size 160x 160mm fixed to plugs with chromium plated brass screws complete all as specified and directed |
| 135 | Demolition of brick work or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed. |
| 136 | Dismantling of stone slabs of any description or thickness, laid dry or laid dry and pointed in floor, apron etc complete all as specified and directed. |
| 137 | Demolition of cement concrete un-reinforced in ground floor and paving not exceeding 15 cm thick (below or above ground level) complete all as specified and directed. |
| 138 | Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided complete all as specified and directed. |
| 139 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. |
| 140 | Dismantling of plain or corrugated steel sheeting,any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed. |
| 141 | Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards / slabs/ blankets any thickness including cover fillets complete all as specified and directed. Please Enable Macros to View BoQ information |
