|
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m i/c carriage of material in all leads and lifts. All kinds of soil. |
| 2 | Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge: including carriage of material in all leads and lifts. All kinds of soil. |
| 3 | Supplying and filling in plinth with sand under floors,including watering, ramming, consolidating and dressing complete. |
| 4 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thickbed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth i/c carriage of material in all leads and lifts. |
| 5 | Providing and laying in position cement concrete of specified gradeexcluding the cost of centering and shuttering - All work up to plinth level 1:2:4 (1 cement : 2 coarse sand) : 4 graded stone aggregate 20 mm nominal size) :including carriage of material in all leads and lifts. |
| 6 | Providing and laying in position cement concrete of specified gradeexcluding the cost of centering and shuttering - All work up to plinth level 1:3:6 (1 cement : 3 coarse sand) : 6 graded stone aggregate40 mm nominal size) :including carriage of material in all leads and lifts. |
| 7 | Providing and laying in position cement concrete of specified gradeexcluding the cost of centering and shuttering - All work up to plinth CC 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) |
| 8 | Providing and laying in position cement concrete of specified gradeexcluding the cost of centering and shuttering - All work below plinth CC 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 40 mm nominal size) |
| 9 | Providing and laying in position machine batched and machine mixed designmix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-incharge.“( Note :- Cement content considered in this item is @ 330 kg/cum.“Excess/ less cement used as per design mix is payable/recoverable separately). |
| 10 | All works upto plinth level |
| 11 | All works above plinth level upto floor V level |
| 12 | Centering and shuttering including strutting, propping etc. and removal of form for: |
| 13 | Foundation footing bases of column |
| 14 | Suspended floors, roofs, landings, balconies and access platform |
| 15 | Lintels, beams,plinth beams, girders, bressumers and cantilevers. |
| 16 | Columns, Pillars, Piers, Abutments, Post sand Struts |
| 17 | Stair case excluding landing |
| 18 | Edges of slabs and breaks in floors and walls, under 20Cm wide |
| 19 | Weather shade, Chajjas, corbels etc., including edges |
| 20 | Retaining Walls, return walls, walls (any thickness ) including attached pilasters, buttresses, plinth and string courses fillets, kerbs and steps etc. |
| 21 | Stone filling behind retaining wall i/c carriage of material in all leads and lifts. |
| 22 | Providing and fixing PVC pipe weep hole 100 mm dia i/c carriage of material in all leads and lifts. |
| 23 | Steel reinforcement for R.C.C work including straightening, cutting,bending, placing in position and binding all complete above plinth level. TMT bars of grade Fe-500D or more i/c carriage of material in all leads and lifts. |
| 24 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand) i/c carriage of material in all leads and lifts. |
| 25 | Providing wood work in frames of doors, windows, clerestory windows andother frames, wrought framed and fixed in position with hold fast lugs or withdash fasteners of required dia & length ( hold fast lugs or dash fastener shallbe paid for separately) i/c carriage of material in all leads and lifts. Second class deodar wood |
| 26 | Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for npanel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick :Float glass panes mm thick glass pane (weight not less than 10 kg per sqm) i/c carriage of material in all leads and lift. |
| 27 | Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws i/c carriage of material in all leads and lifts. |
| 28 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202(Part I) decorative type, core of block board construction with frame of 1stclass hard wood and well matched teak 3 ply veneering with vertical grains orcross bands and face veneers on both faces of shutters i/c carriage of material in all leads and lift.35 mm thick both side laminated board including ISI marked Stainless Steel butt hinges with necessary screws |
| 29 | Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete : 2nd class teak wood50x20 mm i/c carriage of material in all leads and lifts. |
| 30 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete i/c carriage of material in all leads and lifts. Fixed to window |
| 31 | Providing 40X5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nutsm and wooden plugs and embedding in cement concrete block 30X10X15 cm 1:3:6 mix (1 cement:3 coarse sand : 6 graded stone aggregate 20 mm nominal size) i/c carriage of material in all leads and lifts. |
| 32 | Providing and fixing stainless steel sliding door bolts of required color and shade with bolts and nuts, screws etc complete including carriage of material in all leads and lifts. 300x16 mm |
| 33 | Providing and fixing stainless steel Tower bolts of required color and shade with bolts and nuts, screws etc complete including carriage of material in all leads and lifts. |
| 34 | 200X10 mm |
| 35 | 150X10 mm |
| 36 | Providing and fixing stainless steel handles to required colour and shade with necessary screws, etc. complete including carriage of material in all leads and lifts. |
| 37 | 125mm |
| 38 | 100 mm |
| 39 | P/f stainless steel hooks & eye to required shade with necessary screws etc. complete including carriage of material in all leads and lifts. |
| 40 | Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete i/c carriage of material in all leads and lifts. |
| 41 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required i/c carriage of material in all leads and lifts.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 42 | Kota Stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab , including rubbing and polishing complete with base of cement of mortar 1:4 (1 cement :4 coarse sand). 25 mm thick |
| 43 | Kota Stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement of mortar 1:3 (1 cement :3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, inlcuding rubbing and polishing complete including carriage of material in all leads and lifts. |
| 44 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc. complete i/c carriage of material in all leads and lifts. Size of tile 600X600 mm |
| 45 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. i/c carriage of material in all leads and lifts. Size of tile 600X600 mm |
| 46 | Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 60 mm thick C.C. paver block of M-35 grade with approved colour design & pattern |
| 47 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter |
| 48 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion Bend 87.5° 110 m dia. |
| 49 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.including carriage of material in all leads and lifts:-110 mm diameter |
| 50 | 15 mm cement plaster on rough side of single or half brick wall of mix upto all heights/depths in mement Mortor 1:6 (1 cement: 6 coarse sand).i/c carriage of material in all leads & lifts |
| 51 | 20 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand) upto all heights i/c carriage of material in all leads & lifts. |
| 52 | 6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand) upto any height /Depth i/c carriage of material in all leads & lifs. |
| 53 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade: New work (two or more coats) over and including water thinnable priming coat with cement primer including carriage of material in all leads & lifts |
| 54 | Finishing with Delux Multi surface paint system for interiors and exteriors using primer as per manufacturers specifications:Painting steel work with Delux Multi surface paint to give an even shade. Two or more coat applied @0.90 ltr/10 sqm over an under coat of primer applied @0.80ltr/10 sqm of approved brand and manufacturer. |
| 55 | Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives.New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm including carriage of material in all leads & lifts. |
| 56 | Finishing with Delux Multi surface paint system for interiors and exteriors using primer as per manufacturers specifications:Painting wood work with Delux Multi surface paint of required shade. Two or more more coat applied @0.90 ltr/10 Sqm over an under coat of primer applied @ 0.75 ltr/10 sqm of approved brand and manufature i/c carriage of material in all leads and lifts. |
| 57 | Providing and applying white cement based putty of average thickness 1mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete including carriage of material in all leads & lifts. |
| 58 | Brick edging 7 cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S (non modular) bricks of class designation 7.5 inlcuding grouting with cement mortar 1:4 (1 cement:4 coarse sand) i/c carriage of material in all leads and lifts. |
| 59 | Providing and fixing Chest Press Technical Specification Size 2500X 800X 2000 Main frame 100mm OD GI pipe Frame & Handle- 40mm & 31mm OD G.I. pipe. Metal Paint:Powder Coated. All open ends of pipe are to be close by GI/PVC caps for user safety against entrapment. i/c civil work and carriage of material in all leads and lifts. |
| 60 | Providing and fixing Wheel/ Shoulder Twirl Technical Specification:Size 1450X 520X 1750 Main frame 80mm OD GI pipe Frame & Handle-25mm OD G.I. pipe. Metal Paint:Powder Coated. All open ends of pipe are to be close by GI/PVC caps for user safety against entrapment. i/c civil work and carriage of material in all leads and lifts. |
| 61 | Providing and fixing HandRower Technical Specification: Size 1200X 800X 700 Main frame: 100mm OD GI pipe Structure: 80mm OD G.I. pipe. movement: 31mm OD G.I.pipe Handle: 25mm OD G.I. pipe. Metal Paint:Powder Coated. All open ends of pipe are to be close by GI/PVC caps for user safety against entrapment. i/c civil work and carriage of material in all leads and lifts. |
| 62 | Providing and fixing Back Extension Technical Specification: Size 1060X 730X 990mm Main frame 100mm OD GI pipe Foundation plate-M.S. Round Plate of 250mm and 8mm Thick or more Seat Rest Pipe / Seat : GI Pipe 42mm OD or more Seat Rest and Foot Rest: Perforated Galvanished Seat Having Wall Thickness of 2mm as per standred. Metal Paint:Powder Coated. All open ends of pipe are to be close by GI/PVC caps for user safety against entrapment. i/c civil work and carriage of material in all leads and lifts. |
| 63 | Providing and fixing Shoulder Exerciser Technical Specification:Size 1600X 300X1200 Main frame: 80mm OD GI pipe Structure: 31mm& 25mm OD G.I. pipe. Handle: 25mm OD G.I. pipe Revolving Seat : MS Sheet. Metal Paint:Powder Coated. All open ends of pipe are to be close by GI/PVC caps for user safety against entrapment. i/c civil work and carriage of material in all leads and lifts. |
| 64 | Providing and fixing Aerial Stroller Technical Specification:Size 100X 550X1480 Main frame: 100mm OD GI pipe PipeU: 80mm OD G.I. pipe. Leg movement:40mm OD G.I.pipe Handle: 31mm OD G.I. pipe. Metal Paint:Powder Coated. All open ends of pipe are tobe close by GI/PVC caps for user safety against entrapment. i/c civil work and carriage of material in all leads and lifts. |
| 65 | Providing and fixing Leg Extension Technical Specification:Size 1060 MM X 730 MM X 990 MM or as per manufacturer design Main frame 100 MM or more Foundation plate-M.S. Round Plate of 250mm and 8mm Thick or more Arm handle & Rest Seat frame :32/50 NB GI Pipe With 2.65mm Thickness as per standard design Back & Rest Seat & Foot Rest: Perforated Galvanished Seat Having Wall Thickness of 2mm with Precision Punched Hole of 10mm Dia / Cast Iron 325 x 270 x 8 mm thick and M.S Plate of 250 x 200 x 2mm Thick as per standard design Handle Pipe: 33mm OD GI Pipe or more Leg Support :42mm OD GI Pipe or more Seat Rest Pipe: 42mm OD GI Pipe or more Foot Rest Pipe : 42mm OD G.I. Pipe and 80 x 40 mm MS Rectangular Pipe. Metal Paint:Powder Coated. All open ends of pipe are to be close by GI/PVC caps for user safety against entrapment. i/c civil work and carriage of material in all leads and lifts. |
| 66 | Providing and fixing Sky Walker Technical specification: Size 850X800 X 1800 Main frame: 80mm OD GI pipe Leg movement:40mm OD G.I.pipe Handle & Leg: 31mm & 25mm OD G.I. pipe Foor rest : MS Sheet2mm. Metal Paint:Powder Coated. All open ends of pipe are to be close by GI/PVC caps for user safety against entrapment. i/c civil work and carriage of material in all leads and lifts. |
| 67 | Providing and fixing HIP Twister Circular Double Technical specification: Size 1700X1300X1300 Main frame: 80mm OD GI pipe Plate Leg:40mm OD G.I.pipe Handle : 25mm OD G.I. pipe Revolving Plates : MS Sheet. Metal Paint:Powder Coated. All open ends of pipe are to be close by GI/PVC caps for user safety against entrapment. i/c civil work and carriage of material in all leads and lifts. |
| 68 | Providing and fixing Arm Extension Technical specification: Discription: Arm Wheel Dimensions 3 x 2 x 6 (feet) Main Pipe 114MM OD Metal Pipe Supporting Pipe 34MM, 27MM OD Metal Pipe Workout Type Wheel Rotation. Metal Paint:Powder Coated. All open ends of pipe are to be close by GI/ PVC caps for user safety against entrapment. i/c civil work and carriage of material in all leads and lifts. |
| 69 | Providing and fixing Pull up Bars Technical specification: Discription: Chinup Stand Dimensions 3.5 x 1.5 x 4 Ft.Main Pipe 75mm OD Metal Pipe Supporting Pipe 48MM, 34MM OD Metal Pipe Metal Paint: Powder Coated All open ends of pipe are to be close by GI/PVC caps for user safety against entrapment. i/c civil work and carriage of material in all leads and lifts. |
| 70 | Providing and fixing Double seated Pull Chair Technical specification: Discription: Seated Puller Dimensions 6 x 2.75 x 7 (feet) STATION : 2Main Pipe 114mm OD Metal Pipe (3mm Thickness) Supporting Pipe 48MM OD Metal Pipe and 40x40 Metal Box Seat/Back Rotomoulded /Metal Metal Paint:Powder Coated. All open ends of pipe are to be close by GI/PVC capsfor user safety against entrapment. i/c civil work and carriage of material in all leads and lifts. |
| 71 | Providing and fixing Paraller Bar Monkey Bar Discription: Monky BarDimensions 8 x 3 x 7 Ft. Main Pipe 75mm OD Metal Pipe Supporting Pipe 48MM, 34MM OD Metal Pipe Metal Paint:Powder Coated. All open ends of pipe are to be close by GI/PVC caps for user safety against entrapment. i/c civil work and carriage of material in all leads and lifts. Please Enable Macros to View BoQ information |
