|
| 1 | Towards labour charges for Dismantling the damaged Brick work ,Stone masonry including all charges. |
| 2 | Towards labour charges for Dismantling with Pressed tiles including all charges. |
| 3 | Brick Work in CM 1:5 (One part of cement & five parts of sand) mix using Third Class Country Brick Kiln Burnt bricks 8 ¾ \\" x 4 ¼ \\" x 2 ¾\\" including cost and conveyance of materials to work site and including all labour charges for mixing, laying, curing the concrete etc., complete as per standard specifications and as directed by departmental Engineers – TNBP No:31 |
| 4 | Plastering with CM 1:5 (One part of cement & five parts of sand) mix for 12mm thick including cost and conveyance of all materials to work site and including all labour charges for mixing, laying, curing,finishing etc., complete as per standard specifications and as directed by departmental Engineers – TNBP No:56&57 |
| 5 | Finishing with top of roof with one course of machine pressed tiles of size 20cmx20cmx20cm of approved quality laid in cement mortar 1:3 (One cement and three sand) 12mm thick mixed with water proofing compound conforming to ISS by 2% weight of cement used and the joint pointed neatly to full depth of tiles with same water proofing compound mixed with cement motar ,red oxide, etc.complete complying with standard specification as directed by the departmental officers. - 10 m2 TNBP No:44-I |
| 6 | Paving the floor with best quality Vetrified Tiles of size 600 x 600 x 8mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three sand) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works) |
| 7 | Painting the new walls two coats over one coat of priming with best weather proof Exterior Emulsion paint of approved colour and quality including preparation of surface and finishing neatly etc., complete complying with standard specification and as directed by departmental officers Complete as per standard specification. |
| 8 | Painting with two coats of Approved colour of best quality synthetic enamel paint, painting over new iron work including cost and conveyance of all materials and all labour charges etc. complete as per Standard specification and as directed by the departmental officers. (New Iron Surface).TNBP No:66&66-A |
| 9 | Supply and installation of Acoustical False Ceiling ofHigher absorption nubby finish tiles, square edge, glassfibre core fully encapsulated ceiling tile of size595x595x15mmhaving volume density 120 Kgs / m3, weight 1.8/ 2.4 / 3 kg / m2 which is suspended by using 0.3mmthick T15 metal grid system. T15 metal grid system of 600x 600mm module includes WA15 W30 wall angle withunequal flanges of 15 / 19mm, length 3000mm, fixedalong the perimeter of walls with the help of nylonsleevesandsuitable fasteners at 300mm centers. Then suspendthe MT15 W36 MainT with flange width 15mm, height32mm and length 3600mm, from the soffit slab with helpof soffit cleat and wire rod with leveling spring clip at1200mm centres. CT15 W12 CrossT with flange width15mm, height 26mm and length 1200mm is interlockedinto the pre-cut slots in the Main T15 at 600mm centersin the perpendicular direction to the Main T15. Finally,the CT15W06 CrossT with flange width 15mm, height26mm and length 600mm are interlocked into the precutslots in the CT15W12 CrossT in direction parallel to theMain T15 to result in 600 x 600mm module. The Higherabsorption Nubby finish tiles square edge of size 595 x595 x 15mm shall be placed into the grid size of 600 x600mm. Ensure arrow marks behind the tiles are orientedin one direction to achieve uniform shade. The systemsto achieve noise reduction coefficient not less than 0.9NRC, so as to have an neat appearance as directed by thedepartment officers. The cost includes, cost of material,cost of labour, scaffolding, transportation, conveyance,etc. complying to standard specication. M0622 |
| 10 | Supplying, fabricating and fixing in position of Alumi.Anod.natural colour matt finish door half glazed and half PLB board using 12 mm thick PLB board and 5.5 mm thick glazed door using rectangular Alu.Box section of following sizes for frame and shutter with necessary accessories such as rubber beading, Al. Clips, Best double action floor springs, Aluminium Handles on both sides,floor stopper,Tower bolt, Locks and glass including all materials, Labour, power consemption charges required for fabrication if necessary chipping, dismantling making necessary holes in RCC Coloums, Beams or Masonry wherever necessary with power drill to the extent required and made good to the original conditions after fixing etc.,complete. The Alumi. surface must be anodised with matt finish under electrically controlled condition in accordance with IS specification 1868 / 1962 of Anodic filthickness of not less than 15 Microns (Fifteen) for all sections. |
| 11 | Supplying and fixing in position of Alu. Anodised Partition with 62x38x2mm extruded box section at bottom vertical and horizontal members. The vertical member are spaced at 90 cm c/c and to horizontal members are spaced at 1.2M, 2.1M and 2.4M height the bottom panels should be covered with 12 mm thick PLB exterior grade and the top and middle panels should be fixed at 4mm thick glass thick glass with necessary glassing clips.rubber beading, etc., including necessary dismantling holes in RCC columns, beams masonry wherever necessary with power power drill ti the extent required and made good to the original conditions after fixing as directed by the departmental officers. All the Aluminium sections should be anodised to 1.5microns as per ISI specification 1868/1962. |
| 12 | Supplying and fixing in position white / colour glazed European Water Closet of best quality and approved make with 100 mm \\"P\\" or \\"S\\" trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings such as 15mm brass connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe including cost of 600mm length of 110mm dia PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition etc. complete complying with standard specifications. (The EWC and flushing tank wiht all accessories should be got approved by the Executive Enginer before use on works) |
| 13 | Dadooing walls with Glazed tiles of sizes 300mm X 200mm X 6mm size of approved make and quality and colour Set in cement mortar 1:2 (One part of Cement and two part of Plastering Sand (P- Sand)) over 10 mm base layer plastering and pointing with white cement neatly as directed. |
| 14 | Wiring with 2 x 1.5 Sq.mm (22/0.3) PVC insulated single core unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessoires in flush with wall with 3mm thick hylum sheet cover with TW switch box and 5A F.T. switch and making good of the concealed portion with suitable colour for PVC concealed light Point for electronic regulator. (Assume 5 Points Per Coil) (SD-25) |
| 15 | Wiring with 2 x 1.5 Sq.mm (22/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories in flush with wall with 150mm x 100mm x 113mm TW switch box with 3 mm thick hylem sheet cover for 5 A 3 pin non interlocking FT wall socket and 5A FT switch with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed PVC plug point. (SD-38) |
| 16 | Supply and fixing of 20A Flush type Wall Socket 32A DP MCB complete set for AC Plug in flush with wall with earthconnection (For AC Plug) SD 144 |
| 17 | supply and fixing of 18W LED square type Recessed fitting with LED (Higher end) on false Ceiling withsuitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting SD441 |
| 18 | supply and fixing of 30W LED street light fitting with LED (Lower end) with 25mm dia. GI pipe (class B) with 1 no.25mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting SD454 |
| 19 | supply and fixing of 1200mm (48\\") sweep AC ceiling fan 5 star rated complete ( Higher end) with 2module 100W fan step regulator (Higher end) with 1 metre down rod with fan clamp with side platesand cross arm of size 450mm (18\\") SD469 Please Enable Macros to View BoQ information |
