|
| 1 | Earth work in excavation in foundation, trenches etc. includingdressing of sides and ramming of bottoms, including getting out theexcavated material, refilling after laying pipe/ foundation anddisposal of surplus excavated material at a lead upto 50m suitablesite as per direction of Engineer for following depths, below naturalground / Road top level.In all types soils/ saturated soil such as moorum, sand, sandy silt,clay, black cotton soil, kankar, etc.Depth upto 1.5 m9' Wall5' WallWater tank |
| 2 | Earth filling with available surplus soil excavated from foundationsand taken only from outside of building plinth in layers not exceeding20cm in depth, consolidating each deposited layer includingramming and watering and consolidation with lead up to 50 m and liftupto 1.5 m.Under Floor |
| 3 | Providing and laying in position cement concrete of specified gradeexcluding the cost of centring and shuttering - All work upto plinthlevel :1:4:8 (1 Cement : 4 fine/ coarse sand : 8 graded stone aggregate 40mm nominal size).9' Wall5' WallWater tankUnder Floor |
| 4 | Brick work with FPS bricks of class designation 75 in foundationand plinth in:Cement mortar 1:6 (1 cement : 6 coarse sand)1st Course 9' Wall2nd Course 9' Wall3rd Course 9' Wall3rd Course 9' Wall5' WallWater tank |
| 5 | Brick work with FPS bricks of class designation 75 in superstructureabove plinth level upto two stories in all shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand)9' WallDeduction DoorWindow |
| 6 | Half brick masonry with FPS bricks of class designation 75 insuperstructure above plinth level upto two stories.Cement mortar 1:4 (1 cement :4 coarse sand) |
| 7 | Centring and shuttering with plywood or steel sheet upto two storiesor height upto 7.5 metre above plinth level including strutting,propping etc. and removal of form for : |
| 8 | Suspended floors, roofs, landings, balconies and access platform. |
| 9 | Providing and laying in position specified grade of reinforced cementconcrete excluding the cost of centring, shuttering, finishing andreinforcement - All work upto plinth level :1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20mm nominal size) |
| 10 | Reinforced cement concrete work in beams, suspended floors,roofs having slope upto 15° landings, balconies, shelves, chajjas,lintels, bands, plain window sills, staircases and spiral stair casesupto two stories excluding the cost of centring, shuttering, finishingand reinforcement:M-20 Grade Concrete (1:1½:3 (1 cement : 1½ coarse sand : 3graded stone aggregate 20 mm nominal size) -As per design mix) |
| 11 | Reinforcement for R.C.C. work at all levels including straightening,cutting, bending, placing in position and binding all complete |
| 12 | Providing and fixing Marble stone flooring table rubbed, 15-18 mmthick over 20mm (Av.) thick base of CM 1:4 (1 cement : 4 coarsesand) or slab in wal, steps, pillars, counters, jambs, shelves, sills etclaid over 12mm (Av.) thick base of CM 1:3 (1 cement : 3 coarsesand), jointing with white cement mortar 1:2 (1 white cement : 2marble dust) with pigment to match the shade of the marble slabincluding grinding, rubbing and polishing complete.Makrana 'Adanga'.1501 Cm2 to 3600 Cm2 Tiles |
| 13 | Providing and fixing Granite stone slab mirror polished and machineedge cut in walls, pillars, steps, Shelves, Sills Counters, Floors etc.laid on 12mm (Av.) thick base of cement mortar 1:3 (1 cement : 3coarse sand) jointing with white cement mortar 1:2 (1white cement :2 marble dust) with pigment to match the shade of the marble slabincluding grinding, rubbing and polishing complete.Jhunjhunu / Jalore (Red / Choclate Colour)Above 3601 Cm2 Slabs |
| 14 | Cement plastering including T&P, scaffolding, material and completelabpour, including cost of water, curing, racking of joints etc. with 12mm cement plaster of mix :1:6 (1 cement : 6 fine/ coarse sand) |
| 15 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded20mm nominal size stone aggregate) finished with a floating coat ofneat cement including cement slurry, but excluding the cost ofnosing of steps etc. complete.75mm thick |
| 16 | Distempering with oil bound washable distemper of approved brandand manufacture to give an even shade New work (two or more coats) over and including priming coat withcement primer. |
| 17 | Painting with synthetic enamel paint of approved brand andmanufacture to give an even shade :Two or more coats on new work |
| 18 | Providing and fixing pressed steel door frames confirming to IS:4351 manufactured from commercial mild steel sheet of 1.25 mmthickness including hinges jamb, lock jamb, bead and if requiredangle threshold of mild steel angle of section 50x25mm, or base tiesof 1.25mm pressed mild steel welded or rigidly fixed together bymechanical means, adjustable lugs with split end tail to each jambincluding steel butt hinges 2.5mm thick with mortar guards, lockstrike-plate and shock absorbers as specified and applying a coat ofapproved steel primer after pre-treatment of the surface as directedby Engineer-in-charge:Profile E |
| 19 | Providing and fixing factory made ISI marked steel glazed doors,windows and ventilators side /top /centre hung with beading and allmembers such as F7D, F4B, K11 B and K12 B etc. complete ofstandard rolled steel sections, joints mitred and flash butt weldedand sash bars tenoned and rivetted with 15x3mm lugs, 10cm long,embedded in cement concrete blocks 15x10x10cm of 1:3:6 (1cement : 3 coarse sand : 6 graded stone aggregate 20mm nominalsize) or with wooden plugs and screws or rawl plugs and screws orwith fixing clips or with bolts and nuts as required, includingproviding and fixing of hinges, pivots, float glass panes with glazingclips and special metal sash putty of approved make and a primingcoat of approved steel primer excluding the cost of metal beadingand other fittings except necessary hinges or pivots complete as perapproved design. |
| 20 | Providing and fixing external grade board solid core single leaf flushdoor shutters ISI 2202-67 marked using Phenol formal dehyderesinin glue both sides including approved ISI marked Stainless Steel butthinges fittings with necessary screws complete as per annexure 'A' :’Commercial Veneer both side 30 mm thick |
| 21 | Providing and fixing GI wire gauge of average width of aperture1.56mm with wire of 0.45mm to existing steel door, window shutterframes with necessary M.S. strip beading 20x3mm with suitablescrew at not exceeding 150mm distance etc. complete. |
| 22 | Steel work welded in built up sections/ framed work including cutting,hoisting, fixing in position and applying a priming coat of approvedsteel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates andsimilar works. |
| 23 | Providing and fixing 1st quality standard white, grey, ivory, fume redbrown, light green, light blue and other light shades glazed tilesconfirming to IS : 13753 & IS :15622 of size 200mm x 300mm inwalls, floors, steps, pillars etc. laid on a bed of neat cement slurryfinished with flush pointing in the white cement mixed with pigmentto match the shade of the tile complete (excluding the cost ofcement plaster on walls and pillar).er). |
| 24 | Providing and fixing 1st quality MAT finished ceremic tile size300x300mm confirming to IS : 13755 and IS : 15622 colour such aswhite, grey, ivory, fume red brown, light green, light blue and otherlight shades in floors, steps, pillars etc. laid on a bed of neat cementslurry finished with flush pointing in the white cement mixed withpigment to match the shade of the tile complete (including the costof cement mortar bed 1:4). |
| 25 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P.brass pillar taps,32 mm C.P. brass waste of standard pattern,including painting of fittings and brackets, cutting and making goodthe walls wherever require :White Vitreous China Flat back wash basin size 550x400 mm withsingle 15 mm C.P. brass pillar tap. |
| 26 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink asper IS 13983 with C.I. brackets and stainless steel plug 40 mmincluding painting of fittings and brackets, cutting and making goodthe walls wherever required :610x510 mm bowl depth 200 mm. |
| 27 | Providing and fixing white vitreous china water closet squatting pan(Indian type)Orissa pattern W.C. pan of size 580x440 mm |
| 28 | Providing and fixing P.V.C. low level flushing cistern with manuallycontrolled device (handle lever) conforming to IS : 7231, with allfittings and fixtures complete.10 litre capacity - White |
| 29 | Providing and fixing PTMT grating of approved quality and colour.Circular type.100 mm nominal dia. |
| 30 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply including allCPVC plain & brass threaded fittings i/c fixing the pipe with clampsat 1.00 m spacing. This includes jointing of pipes & fittings with onestep CPVC solvent cement and the cost of cutting chases andmaking good the same including testing of joints complete as perdirection of Engineer in Charge.Concealed work including cutting chases and making good the wallsetc.,20 mm nominal outer dia .Pipes. |
| 31 | 32 mm nominal outer dia .Pipes. |
| 32 | Providing and fixing C.P. brass long nose bib cock of approvedquality conforming to IS standards and weighing not less than 810gms. 15 mm nominal bore. |
| 33 | Providing and fixing C.P. brass angle valve for basin mixer andgeyser points of approved quality conforming to IS:8931 15 mm brass |
| 34 | Providing and fixing Unplasticised P.V.C. connection pipe withPTMT Nuts collar and bush of approved quality and colour.15 mm nominal bore with 45 cm length. |
| 35 | P & F Full Way Valve ( IS : 778 Mark ) or wheel valve of approved make Gun Metal 15 mm . |
| 36 | Gun Metal 25 mm. |
| 37 | P & F Sink Cocks of superior quality & approved made:C.P. Sink cock swinging spout 15 mm. |
| 38 | P & F Bol cock (IS :1703 mark) with rod & PVC Ball complete Brass wt.400 gm 15 mm nominal bore |
| 39 | Providing and placing on terrace (at all floor levels) polyethylenewater storage tank ISI : 12701 marked with cover and suitablelocking arrangement and making necessary holes for inlet, outletand overflow pipes but without fittings and the base support for tank |
| 40 | Providing and fixing Unplasticised -PVC pipe clips of approveddesign to Unplasticised - PVC rain water pipes by means of50x50x50mm hard wood plugs, screwed with M.S. screws ofrequired length including cutting brick work and fixing in cementmortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc.complete.75 mm dia |
| 41 | 110 mm dia |
| 42 | P & F rigid PVC pipe fittings ( IS : 4985 mark ) of approved quality / make including jointing the fitting with solvent cement rubber ring and lubricantCoupler 75 mm dia |
| 43 | Plain Tee |
| 44 | Bend 87.5 degree |
| 45 | Vent Cowel |
| 46 | Coupler 110 mm dia |
| 47 | Plain Floor Trap |
| 48 | Multi Floor Trap |
| 49 | Plain Tee |
| 50 | Bend 87.5 degree |
| 51 | Construction of septic tank in all types of soil with 40cm. Thick masonary CM 1:6, 15 cm thick CC bed of 1:5:10, M-15 grade C.C. flooring & over stone slab covering 80mm. Thick slabjointing of slab in CM 1:3 Ralthal, Kharanja, 50mm thick stone partition walls 20mm thick plaster in CM 1:6 finished with neat floating cement 4 Nos. C.I. foot rests of approved design two No. 450mm dia 25 Kg. each C.I. cover with frame earth work etc. complete as per approved drawing including disposal of surplus earth within a lead of 50 mtr. size 200x140x150cm (for 50 users) |
| 52 | Wiring of light point/ fan point/ exhaust fan point/ call bellpoint with 1.5 sq. mm FR PVC insulated unsheathedflexible copper conductor 1.1 kV grade and 1.5 sq.mmFR PVC insulated unsheathed flexible copper earthconductor 1.1 kV grade (IS:694) of approved make insurface / recessed ISI marked medium duty PVCconduit & it's accessories, round tiles,18 SWG M.S. boxwith earth terminal, screwless cage connectors forneutral looping in switch board & false ceiling point. 6 Aswitch, 3.0 mm thick phenolic laminated sheet, zincplated / brass screws, cup washers, makingconnections, testing etc. as required.Group 2short point (upto 3 mtr.) |
| 53 | Medium point (upto 6 mtr.) |
| 54 | Long point ( upto 10 mtr.) |
| 55 | Wiring of 3 pin 5 amp. light plug point with 1.5 sq. mmFR PVC insulated unsheathed flexible copper conductor1.1 kV grade and 1.5 sq.mm FR PVC insulatedunsheathed flexible copper earth conductor 1.1 kVgrade(IS:694) of approved make in surface / recessedISI marked medium duty PVC conduit & it's accessories,18 SWG M.S. box with earth terminal, screwless cageconnectors for neutral looping in switch board & falseceiling point, 6 A switch, 6 A socket, 3.0 mm thickphenolic laminated sheet, zinc plated / brass screws,cup washers, making connections, testing etc. asrequired.. Group 2 On Borard. |
| 56 | Supplying and drawing FR PVC insulated & unsheathedflexible copper conductor ISI marked (IS:694) of 1.1 kVgrade and approved make in existing surface orrecessed conduit/casing capping including makingconnections etc. as required. Group 22 x 1.5 sqm |
| 57 | 2 x 2.5 sqm |
| 58 | P&F Recessed/ Surface mounting heavy duty horizontaltype sheet steel Distribution board phophatised/ powderpainted complete with copper bus bar, shorting link ,neutral link, earth link and din bar masking sheetconforming to IS13032 & IS8623 including makinginternal DB terminations with copper lugs , testing etc.as required.6 Way |
| 59 | P&F 240/415 V MCB of breaking capacity not less than10 KA (B/ C/ D tripping characteristic) ISI marked IS8828(1996)]/ conforming to IEC 60898 in existingboard/sheets including making connections with lugs,testing etc. as required.Single Pole M.C.B.s of rating 6A to 32A group 2 |
| 60 | P&F 240/415 V isolator conforming to IS:13947-III/ IEC60947-3 on existing board / sheet including makingconnections with lugs , testing etc. as required. double pole isolator 63 A rating group 2 |
| 61 | P & F 1.6 mm thick M.S. Recessed fan box, hexagonal/round of size 100 mm dia, depth 75mm, 12 mm dia rodfan hook with 100 mm length extended on each side . |
| 62 | P & F double ball bearing capacitor start ceiling fan ofapproved make complete with regulator and otheraccessories as required. (for estimation purpose only).1200mm sweep.Group-2 |
| 63 | P & F IS:371 marked 6 amp surface type ceiling roseincluding making connection testing etc. as required..Group-2 |
| 64 | P & F ISI marked 6 amp bakelite batten/angle holderincluding making connection testing etc. as required..Group-2 |
| 65 | P & F ISI marked flush type 120/280 watt rotary stepfan regulator including making connection testing etc. asrequired..Group-2 Please Enable Macros to View BoQ information |
