Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Brick work with clay flyash F.P.S. (non modular) brick of class designation 7.5 in superstructure above plinth level up to floor five level in:Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 2 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:3 (1 cement : 3 coarse sand) |
| 3 | 15 mm cement plaster on rough side of single or half brick wall of mix: 1:4 (1 cement: 4 coarse sand) |
| 4 | Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with waterproofing cement compound consisting of applying. (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours.(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.(The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.) |
| 5 | CEMENT CONCRETE (CAST IN SITU)Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 6 | Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately). |
| 7 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 8 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings /wooden frames with rawl plugs screws etc. |
| 9 | Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.80x1.20 mm M.S. laths with 1.20 mm thick top cover |
| 10 | Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof. |
| 11 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement:4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gentlyand easily. Double charge vitrified tile polished finish of size Size of Tile 600 x 600 mm |
| 12 | Glazed vitrified floor tiles polished finish of size Size of Tile 600 x 1200 mm |
| 13 | Glazed Vitrified tiles Matt/Antiskid finish of size Size of Tile 600 x 600 mm |
| 14 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joint with white cement & matching pigments etc. complete.Size of Tile 600x600 mm |
| 15 | Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-inCharge.Granite work |
| 16 | Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge :.)Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. |
| 17 | Providing and fixing removable raised/false access flooring with system and its components of approved make for different plenum height with possible height adjustment upto 50 mm, comprising of modular load bearing floor panels supported on G.I. rectangular stinger frame work and G.I. Pedestal etc. all complete, as per the architectural drawings,as specified and as directed by Engineer-in-charge consisting of: (a) Providing at required spacing to form modular framework, pedestalsmade out of GI tube of thickness minimum 2 mm and 25 mm outerdiameter, fully welded on to the G.I. Base plate of size 100mm x 100mmx 3mm at the bottom of the pedestal tube, G.I. pedestal head of size75mmx75mmx3.5 mm welded with GI fully threaded stud 16mm outer diameter with two GI Check nuts screwed on the stud for level adjustment upto 50mm, locking and stabilizing the pedestal head in position at the required level. The pedestals shall be fixed to the subfloor (base) through base plate using epoxy based adhesive of approved make or the machine screw with rawl plug. (b) Stringers system in all steel construction hot dipped galvanized of rectangular size 570x20x30x0.80mm thick having holes at both ends for securing the stringers on to the pedestal head using fully threaded screws ensuring maximum lateral stability in all directions, the gridformed by the pedestal and stringer assembly shall receive the floor panel, this system shall provide adequate solid, rigid support for access floor panel, the system shall provide a minimum clear uninterrupted clearance between the bottom of the floor for electrical conduits and wiring etc. all complete as per the architectural drawings, as specifiedand as directed by the Engineer-in-charge. (c) Providing and fixing Access Floor panel of 600x600x32 mm medium grade Filled Steel anti static high pressure Lamination of 800H grade (FS800H). Access Floor panel shall be steel welded construction with an enclosed bottom pan with uniform pattern of 64 hemispherical cones. The top and bottom plates of Steel Gauges: top 0.6 mm and bottom 0.7mm fused spot welded together (minimum 64 welds in each dome and 20 welds along each flange). The panel should be Corroresist epoxy coated for lifetime rust protection and cavity formed by the top and bottom plate is filled with Pyrogrip noncombustible Portlandcementitious core mixed with lightweight foaming compound. The access floor shallbe factory finished with Anti-static High Pressure laminate with Non Warp technology upto 1mm thickness for superior adhesion and Surface flatness within 0.75mm.The panel is to withstand a Concentrated Load of 363 kgs applied on area 25mm x 25mm without collapse in the centre of the panel which is placed on four steel blocks. The panel will withstand and Uniformly Distributed Load (UDL) minimum 1250 kg/sqm and an impact load of 50kg all complete as per the approved manufacturers specification and as per the direction of Engineer-in-charge. All specification must be printed on the side of the panel to ensure thequality of the product. 300 mm Finished Floor Height (FFH) |
| 18 | Kota stone FlooringKota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :25 mm thick |
| 19 | For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 20 | 19mm thick prelaminated ply |
| 21 | 12 mm thick marine plywood conforming to IS: 710 |
| 22 | Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick :Ply wood 7 ply, 9 mm thick Decorative plywood one side decorative veneerand commercial veneer on other face (Type 1) conforming to IS 1328 BWR Type |
| 23 | Ply wood 5 ply with commercial ply on both faces 6 mm thick |
| 24 | 12.5 mm thick tapered edge plain gypsum plaster borad confirming toIS 2095 (Part 1):2011 |
| 25 | Providing and fixing 12 mm thick panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick.Fire retardant plywood conforming to IS: 5509 |
| 26 | Providing & Fixing decorative high pressure laminated sheet of plain /wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.1.0 mm thick |
| 27 | Providing and fixing plywood 4 mm thick, one side decorative veneer conforming to IS: 1328 (type-1), for plain lining / cladding with necessary screws, including priming coat on unexposed surface with :Decorative veneer facings of approved manufacture |
| 28 | Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. |
| 29 | Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.Two coats |
| 30 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of stepsand dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 31 | Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre |
| 32 | Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less than 50 grams/ litre |
| 33 | For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 34 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointingcompound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction ofthe Engineer in Charge but excluding the cost of painting with :12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks) |
| 35 | Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge. |
| 36 | Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:(a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixern mixer |
| 37 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :Kitchen sink without drain board610x460 mm bowl depth 200 mm |
| 38 | Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. |
| 39 | Providing and fixing toilet paper holder : C.P. brass |
| 40 | Providing and fixing C.P. brass bib cock of approved quality conformingto IS:8931 : 15 mm nominal bore |
| 41 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:893115mm nominal bore. |
| 42 | Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. |
| 43 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :Rectangular shape 453x357 mm |
| 44 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. |
| 45 | Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.. |
| 46 | Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building allcomplete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent |
| 47 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conformingto IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion..Single tee with door 75x75x75 mm |
| 48 | 110x110x110mm |
| 49 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes |
| 50 | Demolishing of Brick work/ Block, concrete, flooring, MEP services and removal of existing, Door & window, etc. including stacking of serviceable material and Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, for all leads including all lifts involved. (The construction Debris not payable in this item.) |
| 51 | Wood finished vitrified tiles Size 1200mm x 200mm (Tile up to a Basic Rate of Rs: 120 per sft FOR site) |
| 52 | Wood finished vitrified tiles Size 1200mm x 200mm (Tile up to a Basic Rate of Rs: 120 per sft FOR site) |
| 53 | Providing and installation of 75mm high anodized aluminum skirting in an approved premium finish shade, ensuring a high-quality, durable, and aesthetically pleasing solution for edge protection and seamless transitions between flooring and walls. The skirting shall be fabricated from high-grade aluminum, treated with a durable anodized coating for enhanced corrosion resistance, wearability, and uniform color consistency. The installation shall include all necessary hardware and accessories, such as brackets, screws, end caps, and connectors, ensuring a secure and seamless fit with flush joints and smooth alignment. The skirting must be fixed firmly to the substrate using appropriate mechanical fasteners or adhesive (as per manufacturer recommendations), maintaining straightness, levelness, and a gap-free finish against walls. All cuts, miters, and joints shall be precision-made for a clean appearance, with no visible defects or sharp edges. The contractor shall ensure proper surface preparation, including alignment checks and substrate leveling, and protect adjacent surfaces from damage during installation. Upon completion, the skirting shall be free of scratches, dents, or discoloration, with a uniform anodized finish matching the approved sample. |
| 54 | Acoustic Insulation:- Providing and installing Mineral wool of 50 mm thickness and 48kg/cum density packed in hessian cloths fixed with screw, rawl plug & washers and held in position by criss-crossing GI wires etc complete as per directions of Engineer-in-Charge. |
| 55 | Providing and fixing Fabric Wall Panel of specified size in drawings with 12 mm thick pin up board, without sagging, warping or delaminating. Approved fabric (Base rate of Rs 500/- per rm of width 1.2-1.00 Mts.) as selected by the Architect, wrapped around with required foam over pin up board. Complete in all respect as per per the direction of Architect/ Engineer-in-charge. |
| 56 | Providing and fixing decorative routed/ fluted panelling as per the approved design, drawings using high-quality engineered wood/ MDF substrate with premium veneer finish, crafted to achieve precise fluted detailing and seamless joints. The panelling shall be of approved finish and shade. The Contractor shall submit detailed shop drawings for fixing methods, jointing details, and material specifications for prior approval by the Architect/Engineer-in-charge. |
| 57 | Glass PartitionSupply and Fixing of Slim Glass partition of 10mm Toughened Glass using black anodized Aluminium frames to a height as per drawing. The Fixed glass to be fixed using Aluminium frame at Top & Bottom & sides. The profile size to be 45x25MM to be fixed on to the floor/wall/ ceiling as per the architect design. H Junction profile to be used at all Glass to Glass vertical joints, 90 Deg L Junction Profiles and T Junction profiles necessary as per design. In case of Glass overall panel over panel Profile to be used. In case of Open glass edges End Profile to be used. The profiles shall be suitable for Glass thickness of 10/12/13.52mm. The Profile shall be matt Black anodized, the Profile Manufacturer to supply all the necessary clips, seals and fixing accessories for the system.All Profiles to be with 2 mm Gauge thickness Excluding 20 Micron of Anodizing.Approved Manufacturer: Dormakaba/ Jeb/ Alloy |
| 58 | Providing and fixing HPL (High Pressure Laminate - UNI+MR) finished ply boxing to cover the rolling shutter box. The boxing made up of 12mm thick plywood with 1mm thick lamination including all support frame work as per requirement and drawing. The openable panel at bottom. All complete including fitting and fixtures as per drawing, design and direction of architect. |
| 59 | Providing & Fixing of lacquer glass as per approval in any colour fixed with clear neutral silicon of make GE windily 20/ slipup or Dow Corning 995 on a perfectly levelled wall/ any other structure with corner edge/ groove aluminium profile of approved finish & shade. The Lacquered glass shall be highly durable, humid resistance, polyurethane lacquer glass. The glass to be manufactured by industrial curtain coating process. It should meet quality standards as per BS EN 1036 1999 & conform to person hardness test of at least 220 oscillations. The substrate of the glass should confirm to Standard BS EN 572 1995 parts 1 & 2. Lacquered glass to be manufactured to tight specifications, relating to consistency of colour, opacity and homogeneity throughout production campaigns and also to the ageing properties, mechanical resistance, and resistance to humidity and to chemical agents of the lacquer. The colour of the lacquer should remain stable when exposed to normal levels of ultra-violet light in interior applications. |
| 60 | Providing and applying Painting walls by applying a finish of vapor permeable paint with low VOC (base level 8gms /l as per directive 2004/42/CE), (Texture paint of Asian or approved equivalent) in Two or more coats finished with a steel trowel and protecting coats of cera wax to give a smooth finish on wall surface of desired colour and shade over newly prepared wall surface, (included the necessary base preparation required for giving a smooth & even surface to wall/ partitions/ ceiling, scaffolding, padding etc. all complete) |
| 61 | Providing and fixing high-quality furnished curtains as per the approved design, material, and specifications by the architect, including all necessary track systems, rods, hooks, rings, brackets, screws, and fasteners for complete installation. The curtains shall be made from approved fabric with precise measurements, hemming, and stitching to ensure a neat and tailored finish. All hardware components shall be durable, corrosion-resistant, and properly aligned, ensuring smooth operation and aesthetic appeal. (Frisking Area) |
| 62 | Providing & Installing of 3M-designer film/ Wall paper as per selection. (Basic Rate for wall paper/ Film Rs. 2700/- per Sqm). Complete in all respect as per the direction of Architect/Engineer-in-charge. |
| 63 | Providing and Fixing in position of leatherite (as per approval) cladding and stitching as per design and pattern with Consumables (PU foam, etc.) approx. 40mm thickness of foam. Base framing & subase will be paid in respective item. Complete in all respect as per the direction of Architect/ Engineer-in-charge. (Base rate of Leatherite is Rs. 180 per Sqft.) |
| 64 | Providing and fixing Roller Blinds as per the approved sample comprising of screen Fabric comprising of 25% polyester, 75% PVC with openness factor of 5%.Fabric weight 410-465 G weight per sqm, Thickness 0.67 mm. Healthy/safety standard - Oekotex Standard 100.Yarn count 18-19/cm, having fire resistance standard – NFPA 701 Method 1:2004 GB 50222-1995 (B1). |
| 65 | Providing and fixing pelmet as per architectural drawing with 18mm thick base plywood for fixing curtain and roller blinds. All complete as per design, drawing and direction of engineer-in-charge. |
| 66 | Providing and fixing ISI marked 35 mm thick flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class Maple wood and well matched 1.0 mm thick HPL (High Pressure Laminate - UNI+MR) with vertical grain on both faces of shutters, Wooden frame section size 40 x 90-100 mm (frame shall be 90-100mm match with the partition thickness) incl. lamination to be fixed to masonry wall or partition with 6 holdfasts/ fasteners per door. (All Accessories like Hinges, Door handle, lock, stopper, floor closer etc. of Black Anodized Dorma/Hafele make and as specified in drawing to be included & not to be paid separately contractor should takes prior approval for same before procurement). following are some of prescribed model & makes preferred for one leaf of glass shutter:-Dormakaba 3043F, 5 Knuckle, 2 Ball bearing butt hinges size 4\\" x 3\\" x 3mm :- 4 No.Dormakaba TS70B EN3-4 DC Slide Channel - With Hold Open :- 1 No.Dormakaba Mortice sash lock 271a :- 1 No.Dormakaba Lock cylinder DEC 6 Plus 60 :- 1 No. (Selection will be as per door location suitability for locking arrangement)Dormakaba CR 6612 escutcheons :- 1 pair.Dormakaba Pure Lever handle 8100 lever with round roses :- 1 PairDormakaba floor stop half dome with 45mm Dia / Dormakaba 4012 wall mounted door stop :- 1 No.Dormakaba Male / Female sign plate 3020-M /3030-F :- 1 Pair (wherever required) |
| 67 | Providing and fixing ISI marked 35 mm thick flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class Maple wood frame section size 40 x 90-100 mm (frame shall be 90-100mm match with the partition thickness) incl. to be fixed to masonry wall or partition with 6 holdfasts/ fasteners per door. (All Accessories like Hinges, Door handle, lock, stopper, floor closer etc. of Black Anodized Dorma/Hafele make and as specified in drawing to be included & not to be paid separately contractor should takes prior approval for same before procurement). Flush Doors with one side 3.5mm thick approved veneer & Wooden Frame shall be spirit polished / painted and finished with melamine coating /paint to an even shade as per the approval. (Veneer up to a Basic Rate OF Rs-150 per sft FOR site) other side 1.0mm thick HPL (High Pressure Laminate - UNI+MR) of approved shade. following are some of prescribed model & makes preferred for one leaf of glass shutter:-Dormakaba 3043F, 5 Knuckle, 2 Ball bearing butt hinges size 4\\" x 3\\" x 3mm :- 4 No.Dormakaba TS70B EN3-4 DC Slide Channel - With Hold Open :- 1 No.Dormakaba Mortice sash lock 271a :- 1 No.Dormakaba Lock cylinder DEC 6 Plus 60 :- 1 No. (Selection will be as per door location suitability for locking arrangement)Dormakaba CR 6612 escutcheons :- 1 pair.Dormakaba Pure Lever handle 8100 lever with round roses :- 1 PairDormakaba floor stop half dome with 45mm Dia / Dormakaba 4012 wall mounted door stop :- 1 No.Dormakaba Male / Female sign plate 3020-M /3030-F :- 1 Pair (wherever required) |
| 68 | Providing and fixing ISI marked 35 mm thick flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class Maple wood frame section size 40 x 90-100 mm (frame shall be 90-100mm match with the partition thickness) incl. to be fixed to masonry wall or partition with 6 holdfasts/ fasteners per door. (All Accessories like Hinges, Door handle, lock, stopper, floor closer etc. of Black Anodized Dorma/Hafele make and as specified in drawing to be included & not to be paid separately contractor should takes prior approval for same before procurement). Flush Doors with Both side 3.5mm thick approved veneer & Wooden Frame shall be spirit polished / painted and finished with melamine coating /paint to an even shade as per the approval. (Veneer up to a Basic Rate OF Rs-150 per sft FOR site) of approved shade. following are some of prescribed model & makes preferred for one leaf of glass shutter:-Dormakaba 3043F, 5 Knuckle, 2 Ball bearing butt hinges size 4\\" x 3\\" x 3mm :- 4 No.Dormakaba TS70B EN3-4 DC Slide Channel - With Hold Open :- 1 No.Dormakaba Mortice sash lock 271a :- 1 No.Dormakaba Lock cylinder DEC 6 Plus 60 :- 1 No.Dormakaba CR 6612 escutcheons :- 1 pair.Dormakaba Pure Lever handle 8100 lever with round roses :- 1 PairDormakaba floor stop half dome with 45mm Dia / Dormakaba 4012 wall mounted door stop :- 1 No. |
| 69 | Providing and fixing FHC shaft shutters made of powder-coated aluminum frames with glazed shutters, incorporating 6mm thick clear glass panels, complete with all necessary hardware including hinges, handles, and locking arrangements (such as mortise locks or latch mechanisms) to ensure secure and smooth operation, as per approved design and manufacturer's specifications, including proper alignment, sealing, and finishing for a durable and aesthetically compliant installation. |
| 70 | Providing & Making Rectangular/ Square opening over doors with glass. All complete as per design, drawing and direction of engineer-in-charge. |
| 71 | Providing & Making louvers in door with wooden section of 40mm x 10mm at spacing of 25mm c/c. Cost is inclusive of cutting opening in door All complete as per design, drawing and direction of engineer-in-charge. |
| 72 | Providing and fixing Steel Fire Rated door of approved make of two hour fire rating with 1.5 mm thk frame of GPSP sheet. Leaf shall be 44 mm thk or as per manufactures specifications with zinc coating of 120-180 kg/m2 with 4 mm hinge reinforced plates, fixing straps, hardware mounting plates, mortar guard and lock reinforcement. This single leaf door shall be filled with non-combustible mineral fibre infill and exterior surface to be powder coated complete with all hardware of approved make and vision panel of fire rated glass.Size (1100 x 2100 mm ) |
| 73 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointingcompound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction ofthe Engineer in Charge but excluding the cost of painting with :Extra over & above the respective items of gypsum board ceiling for cove up to a width of 600 mm with required shape and size as per design and drawing. |
| 74 | Providing and fixing 15mm thick (Dune RH99 of Armstrong or approved equivalent) microlook tiles of size 600 x 600 mm in true horizontal level suspended on interlocking metal with Prelude XL 15 mm grid system, grid of hot dipped galvanized steel sections (galvanized) consisting of main T runner suitably spaced as per approved manufactures specifications. |
| 75 | GI Metal Ceiling Lay in plain Tegular edge Global white colour tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 mgs/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending with Prelude XL 15 mm grid system, grid of hot dipped galvanized steel sections (galvanized) consisting of main T runner suitably spaced as per approved manufactures specifications. (Approved Makes:- Durlum/ Hanter Douglus/ Knauf) |
| 76 | Providing & Fixing Wooden false Ceiling comprising of 50 x 50 mm hard wood frame treated with anti termite chemical and fire retardant paint of approved makes, spaced at an average spacing of 600mm c/c both ways adequately to the ceiling in line and plumb with the help of wooden plugs and screws fixed & tightened to ceiling etc., covered with 12 mm thick plywood, followed by 6 mm plywood for making groove and finished with a 1.0 mm thick HPL (High Pressure Laminate - UNI+MR) as per drawing. The panels shall have grooves of 10 mm x 7.5 mm. The groove shall be spirit polished and finished with matching colour to give an even shade as per the approval. The ceiling shall be fixed to the roof soffit with adequate suspenders. The item shall be inclusive of cutting & making cutouts for lights, diffusers etc all complete. HPL (High Pressure Laminate - UNI+MR) up to a Basic Rate of Rs-90 per sft FOR site) |
| 77 | Providing and fixing HPL (High Pressure Laminate - UNI+MR)d trap doors in ceiling with required frame at edges for stiffening as per requirement. All complete as per direction of Engineer-in-charge/ Architect. |
| 78 | Providing, fabricating and Installation of MS steel frame work in Ceiling to support services/ Interior works without obstruction of Existing HVAC ducting or other hindrances. Frame will be in MS member as per site requirement and condition. The frame hanged with threaded bolt and anchor fastener from ceiling. The work includes a coat of approved steel primer coat and minimum two coats of enamel paint. (Only Weight of MS frame will measure for payment all Support are inclusive in rate.) |
| 79 | Providing, fabricating and Installation of hanging Metal rods in two rows of size 10x10mm (depth varies from 110 to 800mm) in approved finish hang from ceiling with metal base frame (25x50x25mm / as per design requirement). The frame hanged with threaded bolt and anchor fastener from ceiling. All complete as per design and drawing. The Contractor shall submit detailed shop drawings for fixing methods, jointing details, and material specifications for prior approval by the Architect/ Engineer-in-charge. |
| 80 | Providing & fixing of Tile Based / Open based Workstations of size as given below. The workstation shall have a 25mm thick Plywood worktop finished in 1.0mm thick HPL (High Pressure Laminate - UNI+MR) with post formed edges supported with 25 mm PVC edge bending tape pasted with adhesive. The worktops shall be fixed with the partition panel with suitable supporting system. Panel 50mm thick 1200 Height will be fabric pin-up & lacqurred glass panel and below the top metal Return Panel 1200 Height, 160mm above the top fabric pin-up writing board. The Workstation shall be provided with complete wire management and fascia's for mounting switches at skirting level and above the work top. Each Workstation shall be provided with a 3 DR wooden Pedestal, Metal Keyboard pull tray and CPU Trolley, with all fittings & hardware. (Approved Makes :- Godrej/ HNI ) Linear worktop- Size 1200mm X 600mm, Work Stations |
| 81 | Linear worktop- Size 1350mm X 600mm, Work Stations |
| 82 | Additional Linear worktop for back offices Size varies as per site (to be measured & fabricated as per site condition and requirement beyond the length of linear work top) |
| 83 | Extra for low height modular partition 1200 mm height |
| 84 | Providing, Making and Placing in position counter 750 mm high, length as mentioned below as per design made out of 19 mm thk. block board with or with out 2 drawers storage unit pedestal, one CPU trolly and one keyboard tray. The keyboard tray and drawer shall run on powder coated M.S. channels. Visitor side front exposed surface shall be finished in veneer finished fluted panel and top shall be finished in 3.5mm thick veneer of approved shade finished in melamine polishing. Exposed inside surfaces shall be cold pressed with 1.0 mm thk HPL (High Pressure Laminate - UNI+MR) of approved make as per drawing. Unexposed surfaces shall be finished with 0.8 mm balancing HPL (High Pressure Laminate - UNI+MR). All exposed edges of the board shall be finished with post formed Laminated edges. 6 mm thk. toughened glass shall be fixed above the cash counter as per drawing and details. All complete as per the design and approval of the Architect. Cash counters- length as per drg./ site, 750 mm high, overall 850 depth |
| 85 | Providing and Fixing Cabin table 750 mm high finish, with side table of size and shape as per design. The table shall have supporting frame work (top and vertical surfaces) of 19 mm thk. block board cold pressed with 1.0 thick HPL (High Pressure Laminate - UNI+MR) with post formed PVC edges, storage cabinets of 450 mm width 125 mm deep drawers running on M.S. channels and a 680 mm high & 450 mm wide side unit cabinet with shutters made out of 19 mm thk. commercial block board with back of 6 mm thk. commercial plywood cold pressed with 0.8 mm. thick HPL (High Pressure Laminate - UNI+MR), Backing Laminate on all internal surfaces as per the design and approval of the Architect, all necessary hardware included. Accessories include 3 drawer Wooden pedestal unit with all fittings & hardware, made from 12 mm & 25 mm plywood & HPL (High Pressure Laminate - UNI+MR) finished. MS powder coated keyboard pull out tray CPU Trolley |
| 86 | VFS Academy table (1200 x 750) Providing and Fixing Cabin table 750 mm high below mentioned size and shape as per design and drawing. The table shall have supporting frame work (top and vertical surfaces) of 19 mm thk. block board cold pressed with 1.0 thick HPL (High Pressure Laminate - UNI+MR) with post formed PVC edges. commercial block board with back of 6 mm thk. commercial plywood cold pressed with 0.8 mm. Backing Laminate on all internal surfaces as per the design and approval of the Architect, all necessary hardware included. Accessories include 3 drawer Wooden pedestal unit with all fittings & hardware, made from 12 mm & 25 mm plywood & HPL (High Pressure Laminate - UNI+MR) finished. MS powder coated keyboard pull out tray CPU Trolley 750 mm high, overall 750 depth & length as per drg./ site |
| 87 | Providing, Making and Placing in position 750 mm high, overall 700 depth and width as mentioned below as per design made out of 19 mm thk. block board with drawers, shelf having 6mm thick acrylic divider, unit pedestal, one CPU trolly and one keyboard tray. The keyboard tray and drawer shall run on powder coated M.S. channels. All exposed Internal / External surfaces shall be cold pressed with 3.5 mm thk veneer of approved make and shade. All complete as per drawing. Veneer shall be finish in melamine polish of approved finish and colour. (Side partitions to be measured & paid in respective items) 750 mm high, overall 750 depth & length as per drg./ site |
| 88 | Providing and fixing partition at Premium Lounge submission counter, made with 50mm x 20mm thick solid wooden frame matched with the fixed veneer on table with approved shade of melamine polishing. Cost is inclusive of providing & fixing 10mm thick frosted glass. All complete as per the design and approval of the Architect. (Side partitions to be measured & paid in respective items) |
| 89 | Providing & fabricating low height storage units with 3.5mm thick approved veneer cold pressed over 19 mm thk Block board finished in melamine polish with teak wood leeping post formed edges. Storage is fixed over teak wood legs height of 235mm with 3 drawers storage unit pedestal, one CPU trolly, one keyboard tray, pelmet for wires and cove below for light as per design. Structure/ Body shall be made board with 3 drawer and two shutter of size 350mm x 500mm. wooden pedestal unit with all fittings & hardware, made from 12 mm & 25 mm plywood & 3.5mm thick veneered finished with melamine polished, 450 mm Depth Low height Storage with all hardware & accessories. Size- length as per drg./ site x 450 x 1000 mm |
| 90 | SO / AO Counters (Customized) Providing, Making and Placing in position two level counter 750 mm and 1050 high, overall 850 depth & width as mentioned below as per design made out of 19 mm thk. block/ply board with 3 drawers storage unit pedestal, one CPU trolly, one keyboard tray, pelmet for wires and cove below for light. The machine cutout covered with 6mm thick clear acrylic sheet with SS blade cutter as per drawing. The keyboard tray and drawer shall run on powder coated M.S. channels. All exposed horizontal/ vertical surfaces shall be finished in 1.0 mm thick HPL (High Pressure Laminate - UNI+MR) of approved shade as per drawing. All internal surfaces shall be finished with 0.8 mm balancing High Pressure Laminate. All complete as per the design and approval of the Architect. length as per drg./ site, 850 depth, 750 and 1050mm height |
| 91 | Providing and fixing 8+8mm thick toughened coloured Glass as per selection as partition between two Submission counters as detailed provided in drawings. Size of Glass 450 x 1500mm |
| 92 | Providing and fixing 8mm thick toughened Clear Glass as partition between two Submission counters as detailed provided in drawings. Size of Glass 600x 500mm |
| 93 | Making and Placing in position Interest Kiosk having length length as mentioned below, 600 depth & 750 mm high as per design made out of hard wood frame. Top is made with 19mm thick block board cold pressed with 1.0mm thick HPL (High Pressure Laminate - UNI+MR) of approved make and shade as per drawing. All internal surfaces shall also be finished with matching 0.8mm thick balancing laminate. All exposed edges of the board shall be finished with PVC edges of approved shade. Kiosk shall be provided with a 3 DR wooden Pedestal, Metal Keyboard pull tray and CPU Trolley, etc. incl. all fittings & hardware. All complete as per drawing, design and direction of architect/ Engineer-in-charge.length as per drg./ site, 600 depth & 750 mm height |
| 94 | Providing, making and fixing 380 mm. deep overhead storage cabinets with shutters made out of 19 mm thk. commercial block board with back of 6 mm thk. commercial plywood cold pressed with 1.0 mm. HPL (High Pressure Laminate), 0.8 mm thick Backing Laminate on all internal surfaces as per the design and approval of the Architect including providing well seasoned hard wood at all junctions and exposed edges will be finished in PVC Edge bending tape. cost is inclusive of providing and fixing all hardware. All complete as per drawing, design and direction of architect/ Engineer-in-charge. |
| 95 | Full height Storage Providing, making and fixing 600 mm. deep full height storage cabinets with shutters made out of 19 mm thk. commercial block board with back of 6 mm thk. commercial plywood cold pressed with 1.0 mm. HPL (High Pressure Laminate - UNI+MR), 0.8 mm thick Backing Laminate on all internal surfaces as per the design and approval of the Architect including providing well seasoned hard wood at all junctions and exposed edges will be finished in PVC Edge bending tape. cost is inclusive of providing and fixing all hardware. all complete as per drawing, design and direction of architect. |
| 96 | Low height Storage Providing, making and fixing 450 mm. deep & 750mm height low height storage cabinets with shutters made out of 19 mm thk. commercial block board with back of 6 mm thk. commercial plywood cold pressed with 1.0 mm. HPL (High Pressure Laminate - UNI+MR), 0.8 mm thick Backing Laminate on all internal surfaces as per the design and approval of the Architect including providing well seasoned hard wood at all junctions and exposed edges will be finished in PVC Edge bending tape. cost is inclusive of providing and fixing all hardware. All complete as per drawing, design and direction of architect. |
| 97 | Making and Placing in position Center Table as per Design and Drawing made out of Solid teak wood frame for Base. Top is made with 19mm thick block board. All exposed horizontal/ vertical surfaces shall be cold pressed with 3.5mm thick Veneer of approved make and shade as per drawing. Legs will be made with Solid teak wood as per drawing. All exposed edges of the board shall be finished with teak wood edges. All surface have to finished in melamine polish of approved shade. Premium Lounge coffee table Round type 750 mm Dia A-Type |
| 98 | Premium Lounge coffee table Round type 750 mm Dia B-Type |
| 99 | Making and Placing in position Writing ledge as per Design and Drawing made out of Solid wood frame for Base. Top is made with 19mm thick block board. All exposed horizontal/ vertical surfaces shall be cold pressed with 1.0mm thick HPL (High Pressure Laminate - UNI+MR) of approved make and shade as per drawing. |
| 100 | Making and Placing in position Writing ledge as per Design and Drawing made with 19mm thick block board at top finished in 3.5mm thick Veneer of approved shade & finished in melamine polishing. Substructure shall be made in SS 304 grade tubular section as per drawing. |
| 101 | Making and Placing in position two level counter of length as per drawing, 750mm wide, 750 mm and 1050 high as per detail mentioned in drawing and as per design made out of 19 mm thk. block board with drawers storage unit pedestal, one CPU trolly and one keyboard tray. The keyboard tray and drawer shall run on powder coated M.S. channels. Worktop and vertical surfaces shall be finished in cobination of 12mm thick Solid acrylic surface and Routed MDF of approved pattern as per the design & drawing of approved shade. All internal surfaces shall be finished with 0.8 mm balancing Laminate. All exposed edges of the board shall be finished with post formed Laminated edges. Table- Length as per drg./ site, 750 mm wide & 1050 mm high |
| 102 | Supplying & fabrication of cafeteria table of size as given below with 750 high consisting of a 25mm thick Laminated top with SS (304grade) frame and legs. The top shall be fixed over frame. Table to be open at the bottom without any storage or pedestral unit. complete as per direction of Architect and client. Size 1200mm x 600 x 750 mm |
| 103 | Size 750mm x 600 x 750 mm |
| 104 | Providing and Placing in position office chairs with Chrome plated SS revolving base as per selected model having Gas lift, adjustable arm rest, Sync tilt etc all. Staff Chair - General Lounge, Supervisor, Bio booth and Staff Workstations Mid Mesh back & Navy PU upholstered seat, Recline lock with 4 lockable positions, Moulded foam cushion seat, Wing-shape nylon fixed armrests, Nylon star base on castors. |
| 105 | Manager's Chair :- high Mesh back Breathable ergonomicchair with high density seat cushion, with 4 lockable positions, Wing-shape nylon fixed armrests, Nylon star base on castors |
| 106 | Premium Lounge staff chairs :- Beige PU upholstered seat, Recline lock with 4 lockable positions, Moulded foam cushion seat, Wing-shape nylon fixed armrests, Nylon star base on castors |
| 107 | Premium lounge Applicant Submission Chair - Fully Upholstered Lounge chair with wooden legs Fabric - Aqua clean |
| 108 | Bio booth Low back height Adjustable swivel chair:-PU upholstered seat |
| 109 | Applicants Waiting Area - 3 seaterhigh-density self-skin PU foam seat & back, PU Injection Foam in approved VFS colour. |
| 110 | Cafeteria Chairs:- PP Seat with SS chrome legs |
| 111 | Training room chair |
| 112 | Providing & Placing in position Sofa as detailed in drawing and images. finished, with 100*40 mm density foam for seat & 50*32 mm density foam for back etc all complete. (To be selected by the architect & client) Premium Lounge Single seater sofa / chair (Type-1) |
| 113 | Premium Lounge Single seater sofa (Type-2) |
| 114 | Premium Lounge Two seater sofa (Type-3) |
| 115 | Premium Lounge Single seater sofa (Type-4) |
| 116 | Providing, Making and Placing in position 790 mm high, overall 770 depth & 1800mm Length with side Table of 1050mm Length, 450 mm wide and 790 mm high as per design made out of 19 mm thk. block board with 2 drawers storage unit pedestal, one CPU trolly and one keyboard tray. The keyboard tray and drawer shall run on powder coated M.S. channels. All exposed horizontal/ vertical surfaces shall be cold pressed with 1.0 mm thk HPL (High Pressure Laminate - UNI+MR) of approved make, all complete as per drawing. All internal surfaces shall be finished with 0.8 mm balancing HPL (High Pressure Laminate - UNI+MR). All exposed edges of the board shall be finished with post formed Laminated edges. |
| 117 | Providing, Making and Placing in position 750 mm high, overall 700 depth and width as mentioned below as per design made out of 19 mm thk. block board with drawers, shelf having 6mm thick acrylic divider, unit pedestal, one CPU trolly and one keyboard tray. The keyboard tray and drawer shall run on powder coated M.S. channels. All exposed Internal / External surfaces shall be cold pressed with 1.0mm thick HPL (High Pressure Laminate - UNI+MR) of approved make and shade. All complete as per drawing. Veneer shall be finish in melamine polish of approved finish and colour. (Side partitions to be measured & paid in respective items) 750 mm high, overall 600 depth & 1800mm wide |
| 118 | Providing and Fixing Food and Beverage counter for length required as per site, 750mm wide and 1050 mm high. All exposed side shall be made of fluted panel in approved shade . Cost shall be inclusive of provision and fixing of glass shutter and louvers as per requirement and all necessary hardware. Shutter shall be made in 19mm thick MDF and finished in Duco paint. The counter shall have 18mm thick approved pre polished granite top with 75 mm high edging, storage cabinets shutters made out of 19 mm thk. commercial block board with back of 6 mm thk. Internal / unexposed surfaces shall be cold pressed with 0.8 mm thick HPL (High Pressure Laminate - UNI+MR), as per the design & approval of the Architect. Front Elevated surface shall be measured for payment. |
| 119 | Providing, Making and Placing in position 750 mm high, overall 700 depth and width as mentioned below as per design made out of 19 mm thk. block board with drawers, shelf having 6mm thick acrylic divider, unit pedestal, one CPU trolly and one keyboard tray. The keyboard tray and drawer shall run on powder coated M.S. channels. All exposed Internal / External surfaces shall be cold pressed with 1.0mm thick HPL (High Pressure Laminate - UNI+MR) of approved make and shade. All complete as per drawing. Veneer shall be finish in melamine polish of approved finish and colour. (Side partitions to be measured & paid in respective items) |
| 120 | Providing & Fixing Back lit bevelled edge mirror 6mm th. float glass of modiguard make, complete with 6mm thick hard board ground fixed to wooden cleats with C. P. brass screws and washers complete of the size as given and with maple/ cherry wood frame out of 65x25mm section, as approved by architects, including polishing and finishing. complete in all respects. |
| 121 | Providing & fabricating low height Under counter storage of height 900mm, units with 19 mm thk water proof ply/ Block board cold pressed HPL (High Pressure Laminate - UNI+MR) finished. Structure/ Body shall be made of block board with 2 drawer wooden pedestal unit with all fittings & hardware, made from 12 mm & 19 mm Waterproof plywood & HPL (High Pressure Laminate - UNI+MR) finished, 600 mm Depth Low height Storage with all hardware & accessories. All complete as per design and drawing. |
| 122 | Providing & fabricating powder-coated aluminium louvered shutter for covering electric panels should be fabricated from high-quality aluminium sections with a minimum thickness of 2mm, ensuring durability and strength. The louver blades should be fixed at an angle to allow adequate ventilation while preventing direct exposure to the elements. The entire shutter should be powder-coated with a minimum thickness of 50 microns to provide a smooth, corrosion-resistant finish. The shutter should include a robust locking mechanism for security and be custom-sized to fit the specific dimensions of the electric panels on-site. Installation should include all necessary hardware, such as hinges, screws, and brackets, ensuring a secure and stable fit. The design should comply with relevant safety standards and regulations, providing both functionality and aesthetic appeal. |
| 123 | Providing,Fixing , testing & commissioning Health Faucet of flow rate 4 lpm ABS with double lock 1.2 m long SS flexible hose and wall hook including CP flange. |
| 124 | Providing ,Fixing , testing & commissioning of CP Brass sink mixer for cafeteria sink with wall flange, extended operating lever, swinging spout and surgical purpose handle complete with all accessories as required and making good the walls wherever required. |
| 125 | Providing ,Fixing , testing & commissioning of C.P. brass robe hook with all accessories as required and making good the walls wherever required. |
| 126 | Supplying & installation of Sanitary Fittings including all necessary fittings in the toilet as Directed by the Department. |
| 127 | Providing ,Fixing , testing & commissioning of solid state, no touch operting, fully hygienic hand drier of approved shade with single blower, with time delay, summer & winter control, volume ON/OFF controls including providing necessary brackets, cable from drier to Plug, Plug top key and lock etc, complete as required. |
| 128 | Providing ,Fixing , testing & commissioning of horizontal/vertical storage type water heater of approved shade with copper container with multi-function safety valve for high pressure operation without additional pressure reducing valve, glasswool insulation,stove enamelled M.S jacket, thermostatically controlled inner heater with pilot neon lamps, angle valve on inlet connection, 15mm dia C.P flexible connection pipe in inlet & outlet suitable for working pressure of 5 kg/sqcm complete as required.15 Litre |
| 129 | Providing and fixing uPVC white Floor Trap (FT)with minimum 50mm water seal with rubber seal on inlet to push fit hopper for indirect waste connections complete including cost of cutting and making good the walls and floors where ever required. (100 mm inlet and 100 mm outlet) |
| 130 | Providing and fixing floor drain points formed out of 50 mm dia elbow with suitable extension piece, fitted with 80 mm dia nickel bronze grating and frame, embedded in floor, all complete. |
| 131 | Supply, installation , testing & commissioning 3mm thick Heavy class SS grating of approved design including setting in floor with cement motor to match with floor finish as per architect requirement suitable for FD and FT.a) Size 125 mm dia. |
| 132 | Supply, installation , testing & commissioning uPVC floor/ceiling clean out plug with suitable inlet key for opening male threaded joint with UPVC pipe & socket. Including socketed joint complete as per approved specifications.For 110 mm dia pipe |
| 133 | Supply, installation, testing and commissioning of MS Pipe class 'C' (heavy duty) conforming to IS:1239 including all accessories such as screwed/welded joints, flanges, tees, reducers, structural steel supports and clamps etc. including lift to all heights, welding, jointing, painting and inserted rubber gaskets, nuts, bolts etc. as required. Pipes shall be painted with two coats of primer & two coats of post office red synthetic enamel paint over two coats of red oxide zinc chromate primer. Prior to application of primer surface to be cleaned including painting of legends both direction arrow as per approval of Project Manager and shall be fixed in ceiling, walls, columns for all heights with hangers/supports and fasteners all as per drawing including chasing of walls/columns /ceiling etc. and making good the same as required. G.I. pipe/PVC sleeve of suitable higher size shall be provided whenever the pipes are crossing the walls/floors and sealing the sleeves with glass wool in between & fire sealant compound at either end all as per Project Manager/Consultant requirement. 150 mm dia |
| 134 | 100 mm dia |
| 135 | 80 mm dia |
| 136 | 65 mm dia |
| 137 | 50 mm dia |
| 138 | 40 mm dia |
| 139 | 32 mm dia |
| 140 | 25 mm dia |
| 141 | Providing, fixing, testing and commissioning of C.I. Butterfly valve with cast iron body, cast iron disc and seat of EPDM rubber banded on bakelite with hard back to PN 1.6 (16 kg /cm2 pressure rating) conforming to IS : 13095 with flanges, nut, bolts and washers complete :- 150 mm dia |
| 142 | Providing and fixing Carbon-di-oxide fire extinguishers consisting of welded M.S cylindrical body,squeeze lever discharge valve fitted with internal discharge tube, 30cms long ISI marked high pressure discharge hose, discharge nozzle, suspension bracket, confirming to IS : 934 finished externally with red enamel paint and fixed to wall with brackets with rawl plug/dash fasteners complete with internal charge.Capacity 4.5kg. I.S.I. Marked. (IS : 2878) |
| 143 | Providing and fixing ABC stored pressure dry chemical powder (mono ammonium phosphate) Fire Extinguisher IS : 13849 latest revision manufacturer and of CRCA sheet in welded construction, finish with epoxy polyster powder coated complete with brass forged ball valve, gun metal cap and nozzle, including initial filled and wall suspension bracket (suitable for fighting in class 'A', B & 'C' that is wood, textile, flammable liquid, electric and gases.Capacity 4 Kg (IS : 13849) |
| 144 | Providing and fixing 25 mm dia inspection & testing assembly with gun metal Gate valve, gun metal sight glass, drain valve (Ball valve 50mm dia) & connection to drain. |
| 145 | HVAC WORKS-Variable Refrigerant Volume SystemSupply of variable refrigerant volume/flow modular type air-conditioning system (Top Discharge) with all inverter compressor complete with indoor and outdoor units with individual controller with refrigerant piping, gas charging R-410A, M.S. stand with corrison resistant paint, Vibration Isolation pad ,control cabling, Y-joints & Canvass connection between indoor unit & supply air duct as per detail given in specifications and drawing complete in all respect. Make - Mitsubishi Electric, O General , Daikin etc Outdoor Unit 34HP (16HP+18HP) |
| 146 | Indoor Units-Supply of Indoor UnitsCity Multi Cassette IDU 4 Way 1.59 TR |
| 147 | City Multi Cassette IDU 4 Way 2.56 TR |
| 148 | Ceiling Concealed Unit of 4 TR Nominal Capacity with Drain Pump |
| 149 | Ceiling Concealed High Static Ducted Unit of 6.4 TR Nominal Capacity without Drain Pump |
| 150 | Supply of Accessories Wireless Remote Handset |
| 151 | Wireless Signal Receiver for Ceiling Concealed Ducted Units |
| 152 | Simple Central Controller for 50 IDUs |
| 153 | VRF Refnet Joints:Supply, Installation, Testing & Commissioning of Refnet Branch Joint |
| 154 | Supply of Mitsubishi Electric make Inverter Model 5 Star Hi-Wall Split Type AC 1.5 TR 5-Star |
| 155 | PART-B: SUPPLY OF INSTALLATION, TESTING & COMMISSIONING LOW SIDE PART B HVAC SYSTEMInstallation, Testing and Commissioning of 415V , 3 Ph - 50HZ Aircooled Type Top Discharge VRF SYSTEM Unit, compresing of inverter technology based heametically sealed scroll/Rotary compressor with R410a Refrigerant, Aircooled Condenser along with inbuilt microprocessor panel.34 HP Cooling Only Top Discharge (16 HP + 18 HP) |
| 156 | Installation Testing and Commissioning of 4-Way Circular Air Flow Cassette Unit with 360°direction air flow , high efficient DC fan motor with seamless airflow with auto swing louver, dx copper coil, prefilter, fan section, electronic expansion valve, corded remotes etc. Minimum capacities of each Evaporative units are as follows: City Multi Cassette IDU 4 Way 1.59 TR |
| 157 | City Multi Cassette IDU 4 Way 2.56 TR |
| 158 | Installation Testing and Commissioning of Hi-Static duct type indoor unit with cordless remote, comprising of blower fan / runner, coils , thermostat, pulse modulating electronic expansion valve (PMV), tubes,fins etc. Minimum capacities of each Evaporative units are as follows: 4.0 TR |
| 159 | 6.4 TR |
| 160 | Installation, Testing & Commissioning of Central Remote Controller for controlling all IDU & ODU |
| 161 | Installation, Testing & Commissioning of 5 Star Rated Inverter Unitary Hiwall Split AC with R32/R410A Eco-Friendly Refrigerant along with 10 meters copper piping and cable. Each outdoor unit to be placed on ready-made powder coated L-type ODU stands.1.5 TR |
| 162 | Refrigerant Piping (VRV)Supply, installation and testing of interconnecting refrigerant pipe work with 13 mm / 19 mm thick closed cell elastomeric nitrile rubber tubular insulation between each set of indoor & outdoor units, all the copper piping shall be eddy current test certified, as per specifications, all piping inside the room shall be properly supported as per specification and drawings.(Make - Mandev/ Maxflow/ Mehta Tubes/ Indigo)34.9 mm O.D.(insulation : 19 mm) |
| 163 | 28.6 mm O.D.(insulation : 19 mm) |
| 164 | 22.2 mm O.D.(insulation : 19 mm) |
| 165 | 19.1 mm O.D.(insulation : 19 mm) |
| 166 | 15.9 mm O.D.(insulation : 13 mm) |
| 167 | 12.7 mm O.D.(insulation : 13 mm) |
| 168 | 9.5 mm O.D.(insulation : 13 mm) |
| 169 | 6.4 mm O.D.(insulation : 13 mm) |
| 170 | Drain PipingSupply, installation and testing of UPVC drain piping complete with fittings, U-trap, supports valves and insulate with 9 mm thick Nitrile rubber insulation complete as per standards, requirements and drawings.(Make - Prince/ Supreme)50 mm dia |
| 171 | 40 mm dia |
| 172 | 32 mm dia |
| 173 | 25 mm dia |
| 174 | Drain Pumps for Hi Wall UnitProviding & fixing of drain pumps for Hi Wall of required capacity complete in all respect. |
| 175 | Inline FansSupply, installation, testing and commissioning of inline cabinet/ circular type of GI/ Tough Reinforced plastic construction complete with centrifugal fan with motor, drive, canvass connection at inlet & outlet complete with MCB panel with cabling and earthing (with 5 Rm). Fan shall be suitable for operation on 220 ± 10 volts, 50 Hz, single Phase AC power supply. All single phase inline fans shall be provided with factory filled speed regulation and as per specification and drawings.(Make - Ostberg/ Airflow/ Caryaire/ Sphere)700 CFM, 15 mmwg SP with pre filter |
| 176 | 700 CFM, 10 mmwg |
| 177 | PIR Panel DuctingSupply & Installation of Factory Pre-cut SMART Pre-Insulated ECO+ PIR Panels complete CFC & HCFC Free 20 mm thick with FSK Reinforced Aluminium foil on one side and 80 micron Embossed Aluminium foil (Anti microbial, Anti fungal, Anti corrosion and UV Protection coating) on the other side and close cell not less than 95% Rigid Cellular foam insulation of thickness as specified below and material shall be Class O as per BS 476 Part 6 & Part 7 with 2 hours fire rating, with Density of 46kg/m3 and should have Thermal Conductivity 0.023 W/mK , Water absorption shall be not more than 0.03% as per EN 13403 standard and panel should be GreenPro certifed. The ductwork should be capable of handling pressures upto 2000 Pascals. The joint between the ducts shall be with Polymer slide in type joint between the ducts and all other polymer accessories to be of the same manufacturer. Measurement would be done on outer to outer. Supporting of Wired supporting of approved make to be provided.(Make - Asawa)(PIR Panel Ducting-Rectangular)20 mm thickness |
| 178 | G.I. Sheet Metal Ducting factory fabricatedSupply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/ elliptical ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as per specifications, requirement, standardard and drawings.G.I. Sheet Metal Ducting (Rectangular)Thickness 0.63 mm sheet (24 Gauge) |
| 179 | Thickness 0.80 mm sheet (22 Gauge) |
| 180 | Duct Acoustic LiningSupply & installation of duct acoustic lining with glass wool insulation boards, coverd with perforated aluminium sheet, nuts, bolts etc. (Make - Aerocell/K-flex/Armacell)25 mm thick, 32 kg/m3 density |
| 181 | Grilles / DiffuserSupply & installation of aluminium powder coated supply and return air grilles/diffusers as per specifications and drawings.(Make - Caryaire/ Mapro/ Balance Air/ Cynor/ Conaire)Aluminium supply air diffuser with damper. |
| 182 | Aluminium return air diffuser without damper. |
| 183 | Aluminium supply air grill with damper. |
| 184 | Aluminium return air grill without damper. |
| 185 | Volume Control DamperSupply, installation, testing and commissioning of GI volume control duct damper complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc., as per specifications.(Make - Caryaire/ Mapro/ Balance Air/ Cynor/ Conaire) |
| 186 | LouversSupply & installation of louvers & bird screen as per specifications and drawings.(Make - Caryaire/ Mapro/ Balance Air/ Cynor/ Conaire) |
| 187 | Canvas ConnectionSupply and Installation of Fire Resistant Fabric Flexible Connection to be installed between all the ductable Indoor units and the ducting to provide flexibility of movement in case of a seismic event and to prevent transmission of vibration from the unit to the duct. The fabric should be fire resistant, fiberglass weave with silicone rubber coating with Galvanized metal strip as per specifications. Flexible duct connector fabric shall be air tight, waterproof, virtually chemically inert and shall not emit toxic fumes when exposed to open flame. The width of the flexible connection fabric shall not be less than 150 mm. The flexible canvas connector shall be tested and certified in accordance with BS 476 Part 7 Class 1 and NFPA 701 from NABL accredited laboratory. |
| 188 | Control & Transmission WiringSupply & installation of control cum transmission wiring of 2 core X 1.5 sqmm armoured copper in suitable conduits between indoor and outdoor unit.(Make - Havells/ Polycab/ Rallison) |
| 189 | Controller WiringSupply & installation of control wiring of 2 core X 1.5 sqmm armoured copper between indoor units and their wired remote.(Make - Havells/ Polycab/ Rallison) |
| 190 | Isolator/ ELCBSupply & fixing of following rating weather proof IP-65 endosure isolators/ ELCB with all accessories including Copper cabling from isolator to equipment as required for following as per specifications, standards & requirement.(Make - ABB/ Siemens/ Havells)For 18 HP Outdoor Unit ( 63 Amp.) |
| 191 | For 16 HP Outdoor Unit ( 63 Amp.) |
| 192 | Power CablingSupply & fixing of PVC sheathed Copper cables for various equipments through walls/ceiling with appropriate clamps & fixing arrangement including terminations as per specifications and drawings. (Make - Havells/ Polycab/ Rallison) 4C - 10 sqmm (Copper cable) |
| 193 | Cable / Pipe TraySupply & installation of 22 gauge perforated G.I. painted covered cable tray of below mentioned size for running refrigerant piping along with control wiring etc. cable tray should be properly clamped and hang with all connected accessories.(Make - MEM)150 mm width X 50 mm depth X 1.6 mm thickness |
| 194 | 200 mm width X 50 mm depth X 1.6 mm thickness |
| 195 | EarthingDouble earthing continuity conductors of G.S.S between panel boards and equipments as required. |
| 196 | ELECTRICAL WORKSMAIN DISTRIBUTION BOARDS-Design, fabrication, assembling, wiring and supply of Distribution Panel, fabricated out of (load bearing member of 2mm and non load bearing member 1.6 mm thick) CRCA sheet steel in cubicle compartmentised modular 3b construction, free standing floor mounted with bottom cable entry, dust and vermin proof with reinforcement of suitable size angle iron, channel, `T’ sections and / or flats wherever necessary. 3 mm thick cable gland plates shall be provided on top as well as at the bottom of the panels. Panels shall be treated with all anticorrosive process before powder coating as per specifications and final approved shade. 2 Nos. earthing terminals shall be provided for all distrtibution panels. Panels shall be suitable for 415V, 3 phase, 4 wire, 50 HZ supply system. Lifting hooks shall also be provided in case of large panels. Approval shall be taken for each panel in the form of shop drawings before fabrication. Galvanised hardwares with zinc passivation shall be used in fabrication of panels.MDB - 1 (L,P & AHU PANEL) (Electrical Room) (1F)Incomer from Existing Rising Main comprising of :160 amps FP MCCB with Thermal magnetic release for SC and OL protection etc. - 1 Set. Multifunction meter for VAF, PF, Power & eneregy with RS - 485 port equivalent to Schneider make EM6436H with 160/5, 15 VA, CL 0.5, 3 No. CTs- 1 Set.ON / OFF / TRIP indicating lights with control MCB - 1 Set.Phase indicating light protected by 2 amps MCB’s - 1 Set .Bus Bar comprising of :200 Amps 4 Pole Aluminium Bus Bar with colour coded heat shrinkable steeve - 1 set.Outgoing comprising of :63 amps 4 Pole MCB - 7 Set.40 amps 4 Pole MCB - 2 Set.32 amps 4 Pole MCB - 1 Set.40 amps 2 Pole MCB - 1 Set.Notes:-All MCCB breakers shall be minimum 25 kA rating with Icu = Ics & All MCB breakers shall be minimum 10 kA rating with Icu = Ics.MDB - 1 (L,P & AHU PANEL) (Electrical Room) (1F) described as above |
| 197 | MDB - U-1 (UPS Panel) (Electrical Room) (First Floor).Incomer From MDB-U-1 comprising of :63 amps FP MCB with Thermal Magnetic based release for SC & OL protections - 1 Set.Multifunction meter for VAF, PF, Power & eneregy with RS - 485 port equivalent to Schneider make EM6436H with 63/5, 5 VA, CL 0.5, 3 No. CTs- 1 Set.ON / OFF / TRIP indicating lights with control MCB - 1 Set.Phase indicating light protected by 2 amps MCB’s - 1 Set.Bus Bar comprising of :100 Amps 4 Pole Aluminium Bus Bar with colour coded heat shrinkable steeve - 1 set.Outgoing comprising of :40 amps 2 Pole MCB - 6 Set.Notes:-All MCCB breakers shall be minimum 25 kA rating with Icu = Ics & All MCB breakers shall be minimum 10 kA rating with Icu = Ics.MDB - U-1 (UPS Panel) (Electrical Room) (First Floor) described as above |
| 198 | Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)6 way (4 + 18), Double door |
| 199 | Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's (but without MCB's and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)12 way (4 + 36), Double door |
| 200 | Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)2 + 8 way, Double door |
| 201 | 2 + 12 way, Double door |
| 202 | Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps |
| 203 | Supply & Laying of non skid Electro mat 1mtr wide and 2.0 mm thick 1.1KV grade IS 15652 as required including cutting to required length complete as per requirement of local electricity authorities. |
| 204 | Supply and fixing in position the approved \\"shock treatment charts\\" framed in teak wood frame and covered with glass in front as required in two languages (Hindi & English) |
| 205 | Supply of standard first aid box as approved by Indian red cross society/ St.John Ambulance Brigade and conforming to IS 2217-1963. |
| 206 | LT CABLES, CABLE TRAYS & RACEWAYS:Supplying & laying of following 1100 volt grade XLPE insulated PVC sheathed Aluminium conductor armoured cables as per specification in existing trenches, pipes, cable trays, ducts, over bed of sand, clamped to wall with suitable clamps including, saddles fixing bolts, connecting testing and commissioning complete in all respect as required as per site conditions.3.5 core 70 sq.mm Al arm. |
| 207 | 4 core 25 sq. mm Al arm. |
| 208 | 4 core 16 sq. mm. Cu arm. |
| 209 | 4 core 10 sq. mm. Cu arm. |
| 210 | 3 core 6 sq.mm Cu arm. |
| 211 | 1 core 16 sq.mm arm Cu cable for UPS Connectivity |
| 212 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3½ X 70 sq. mm (38mm) |
| 213 | 4 X 25 sq. mm (28mm) |
| 214 | 4 X 16 sq. mm (28mm) |
| 215 | 4 X 10 sq. mm (25mm) |
| 216 | 2 X 6 sq. mm (19mm) |
| 217 | 2 X 16 sq. mm (22mm) |
| 218 | Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.100 mm width X 50 mm depth X 1.6 mm thickness |
| 219 | 150 mm width X 50 mm depth X 1.6 mm thickness |
| 220 | 200 mm width X 50 mm depth X 1.6 mm thickness |
| 221 | 300 mm width X 50 mm depth X 1.6 mm thickness |
| 222 | EARTHING SYSTEMProviding and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required. |
| 223 | Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.with lockable terminal box in 1.6mm thick with MS enclosure with transperant cover with 1 no. (300 mm length) 50 x 6 mm copper strip on epoxy insulators with 20 no. 8mm dia holes with 8mm x 25mm dia brass nut bolt with double washer |
| 224 | Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm) |
| 225 | WIRING & CONDUITINGWiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire |
| 226 | Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit along with 1 No 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. |
| 227 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required5/6 amps switch |
| 228 | 15/16 amp switch |
| 229 | 3 pin 5/6 amp socket outlet |
| 230 | 6 pin 15/16 amp socket outlet |
| 231 | Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole |
| 232 | INTERNAL LIGHTING FIXTURES2ft x 2ft IP-44 rated, 40W LED ceiling recessed/Surface panel light - Indoor luminaire with prismatic diffuser which gives soft & even light distribution should be Powder coated CRCA housing with aluminium front frame High efficiency translucent diffuser for glare free, uniform light distribution.Cable entries for through-wiring of mains supply cable. CRI (Ra) : >80, SDCM≤ 3 to avoid color deviation, Led life should be atleast L70B10 50,000hrs with minimum luminous flux (delivered lumens) of 110 lm/W, prewired with constant current LED driver and suitable for operation on 240V, 50Hz single phase ac supply, Power Supply : Integrated Power Factor : >0.95 THD : <10% Surge Protection : 2.5KV Efficiency : >85%. Driver Integrated : Constant Current Input Voltage : 230-240Vac Frequency : 50-60Hz Operating Voltage : 180-240Vac Operating Temperature : -15°~+50°C. CE,BIS, Dialux calculation must be done before supply with desired lux level for the particular area as per guidline and on direction of Architect. Approved Makes:- Havells/ Wipro/ Abby/ Philips |
| 233 | 35 Watt LED Panel Light Fixtue with minimum luminaire system efficacy of 100 lm/w having a color temperature of 5700K and housing should made up of pressure die cast aluminium with high efficiency diffuser with driver, IP66, PF>0.9, THD<10%, accessories wiring etc. Approved Makes:- Havells/ Wipro/ Abby/ Philips |
| 234 | 20 Watt Concealed LED Light Fixture with minimum luminaire system efficacy of 100 lm/w having a color temperature of 6000K and housing should made up of pressure die cast aluminium with high efficiency diffuser with driver, IP66, PF>0.9, THD<10%, accessories wiring . Approved Makes:- Havells/ Wipro/ Abby/ Philips |
| 235 | 24 Watt Hanging LED Light Fixture with minimum luminaire system efficacy of 100 lm/w having a color temperature of 4000K and housing should made up of pressure die cast aluminium with high efficiency diffuser with driver, IP66, PF>0.9, THD<10%, accessories wiring. Approved Makes:- Havells/ Wipro/ Abby/ Philips |
| 236 | 12 Watt LED Downlight with minimum luminaire system efficacy of 100 lm/w having a color temperature of 6000K and housing should made up of pressure die cast aluminium with high efficiency diffuser with driver, PF>0.9, THD<10%, accessories wiring etc. Approved Makes:- Havells/ Wipro/ Abby/ Philips |
| 237 | 10 Watt LED Down light fixture with minimum luminaire system efficacy of 100 lm/w having a color temperature of 4000K and housing should made up of pressure die cast aluminium with high efficiency diffuser with driver, accessories wiring etc. Approved Makes:- Havells/ Wipro/ Abby/ Philips |
| 238 | Flexible led strip for cove light available in 3000K/4000K/ 5700K. Complete with aluminium channel and drivers. Makes:- Havells/ Wipro/ Abby/ Philips |
| 239 | INFRASTRUCTURE FOR IT & TV SYSTEMSupplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.25 mm |
| 240 | 32 mm |
| 241 | Supply & fixing of one no. RJ 45 jack for Data / Voice / IPTV outlet of approved make and design in 1.6 mm thick GI box with grid plates with earthing complete in all respect.Outlet for . Data / Voice with information outlet for cable termination |
| 242 | Supplying and drawing of UTP 4 pair CAT 6 A LAN Cable in the existing surface/ recessed steel/ PVC conduit as required.1 run of cable |
| 243 | UPSSupplying, installation, testing and commissioning of 20 kVA online double conversion fully microprocessor based ,indoor type, compact UPS system of following rating with IGBT based PWM technology to achieve THD < 3% and input power factor of greater than 0.95 at 50% loading,suitable for Three phase AC input voltage 380 V to 440 V, 50 Hz +3% / - 3 % and Three phase AC output voltage 415 ± 1% volts & frequency 50 ± 0.5 Hz , inbuilt isolation transformer, necessary VRLA batteries of suitable size having 20 minutes back up time , mounting rack including and suitable size connecting cable (for UPS to Battery and battery to battery), static and maintenance bypass switch, SNMP card for RS232/ RS485 computability for operation and monitoring etc. with all components as mentioned in BOQ, specifications and schedule, complete as required.Note : Concerning vendor needs to furnish the battery sizing calculations at the time of GA approval and battery size has to be as per the approved GA drawing. |
| 244 | FIRE ALARM SYSTEMSupplying, installation, testing and commissioning of micro processor based intelligent addressable main fire alarm panel, central processing unit with the following loop modules and capable of supporting not less than 240 devices (including detectors) and minimum 120 detectors per loop and loop length up to 2 km, network communication card, minimum 320 character graphics/ LCD display with touch screen or other keypad and minimum 4000 events history log in the non volatile memory (EPROM), power supply unit (230 ± 5% V, 50 hz), 48 hrs back-up with 24 volt sealed maintenance free batteries with automatic charger. The panel shall have facility to connect printer to printout log and facility to have seamless integration with analog/digital voice evacuation system (which is part of the schedule of work under SH: PA System) and shall be complete with all accessories . The panel shall be compatible for IBMS system with open protocol BACnet/ Modbus over IP complete as per specifications. Two Loop Panel. |
| 245 | Supplying, installation, testing & commissioning of central graphical fire alarm management system to centrally monitor and operate the fire alarm system complete as required. Note: Multi user free license software with Graphics, 50 inch screen, PC, laser printer shall be included and connected to BMS thru Modbus with Mobile messaging (upto 5 No.) for Fire alarm, maintenance alert to be included. SIM card shall be provided by client. |
| 246 | Supplying, installation, testing & commissioning of repeater panel wih 320 character/ Touch screen LCD display with inbuilt reset, acknowledge and silence switches complete as required. |
| 247 | Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required. |
| 248 | Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc as required. |
| 249 | Supplying, installation, testing & commissioning of fault isolator complete with base as required. |
| 250 | Supplying, installation, testing & commissioning of intelligent interface unit BACnet/ Modbus protocol i.e. supplying communication links between building management system and fire alarm control panel complete as required. Note: Multi user free license software with Graphics, 50 inch screen, PC, laser printer shall be included and connected to BMS thru Modbus with Mobile messaging (upto 5 No.) for Fire alarm, maintenance alert to be included. SIM card shall be provided by client. |
| 251 | Supply, installation, testing and commissioning of the Addressable control relay modules complete as required as per specifications. |
| 252 | Supply, installation, testing and commissioning of the Addressable Monitor modules complete as required as per specifications. |
| 253 | Supplying, installation, testing & commissioning of addressable manual call point complete as required. |
| 254 | Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required. |
| 255 | Supplying, installation, testing & commissioning of fire fighter phone jack complete as required. |
| 256 | Supplying, installation, testing & commissioning of 1.5/3/6W metal box ceiling/wall speakers complete as required.including addressing module having an audible range of 25 meters, and providing/fixing 1.6 mm thick GI box with grid plates with earthing complete in all respect as required. |
| 257 | Supplying & laying of 2x1.5 sqmm fire survival armoured cable, 600/1000V rated with annealed copper conductor having glass mica fire barrier tape covered by an extruded layer of Cross Linkable Ethylene Propylene Rubber (EPR) insulation and LSZH inner bedding, steel wire armouring & LSZH outer sheath complete as required. |
| 258 | IT WORKSHardware including PheriperalsDesktop - SO Counter Desktop- HP Pro SFF 280 G9 R - i5 + 16 GB + 500 GB SSD, Win 11 professional with 3 years warranty |
| 259 | Laptop -HP 440 G10 i5 + 16 GB + 500 GB SSD, Win 11 pro with 3 years warranty or equivalent |
| 260 | Laser Printer -(HP - LJ 1020) or equivalent |
| 261 | All in One Printer - (HP MFP - 226/227) or equivalent |
| 262 | Barcode Printer (Zebra ZD 420) or equivalent |
| 263 | Barcode Scanner - Zebra DS2208 With Stand2D or equivalent |
| 264 | Impact Printer - (Epson TM-U220D) or equivalent |
| 265 | Flatbed Scanner - (Canon Lid 400) or equivalent |
| 266 | Flatbed Scanner - High End (Fijutsu - 7160 / 7180) or equivalent |
| 267 | Passport reader- MRZ (Access - OCR 316) or equivalent |
| 268 | PPR OSMOND ADR or equivalent |
| 269 | Passport Reader Keyboard (Access 423 / 500) or equivalent |
| 270 | Touch Screen for QMS HP/Lenovo 18.5\\" TS or above or equivalent |
| 271 | Thermal Printer For QMS (80MM) or equivalent |
| 272 | Hardware Server for QMS Desktop- HP Pro SFF 280 G9 R - i5 + 16 GB + 500 GB SSD, Win 11 professional with 3 years warranty or equivalent |
| 273 | UPS UPS for IT Equipments Numeric 30 KVA with Battery Bank for 30 mins backup or equivalent |
| 274 | UPS - for other department ( Securirty) Numeric 10 KVA with Battery Bank for 30 mins backup or equivalent |
| 275 | Cabling and Network Room SetupPatch Panel 24 port |
| 276 | Rack APC 42 U |
| 277 | Switch HP Aruba 1830-2 or C1300-24T-4G - 24 port or equivalent |
| 278 | Firewall FG-60F - 10 x GE RJ45 ports (including 7 x Internal Ports, 2 x WAN Ports, 1 x DMZ Port). FC-10-0060F- 950-02-12 - Unified Threat Protection (UTP) (IPS, Advanced Malware Protection, Application Control, URL, DNS and Video Filtering, Antispam |
| 279 | BIO KIT UKMANTRA Custom Biometric Enrolment kit as per VFS specifications, with HID Gaurdian 200 |
| 280 | Individual BIO Kit for Other missionMobile Suite Case - Individual BIO Kit - Customized Bag |
| 281 | Fingerprint Scanner - Crossmatch - Guardian 200 - Resolution = 500 ppi, Image capture area = 81 x 76 mm, Sensor type = Optical |
| 282 | Fingerprint Scanner - Crossmatch Patrol - for Schengen mission |
| 283 | Biometric Device - Single Finger / Mantra MELO20 - for Citizen Services Assam |
| 284 | Signature Pad - Wacom (STU -540, 300, 430, 500) |
| 285 | Passport reader- (Access - OCR 640) |
| 286 | CAMERA (1300, 1500, 2000D) - For Individual, Camera Power Adapter,Camera USB Cable (1.5 Meter), Tripod |
| 287 | Barcode Scanner - Biometric - SYMBOL LS2208 |
| 288 | Network Cabling excluding Patch Cords |
| 289 | Network Cabling - Only Patch Cords 2 mtr Patch Cords |
| 290 | Network Cabling - Only Patch Cords 1 mtr Patch Cords |
| 291 | IT consumable (Camera Power Adapter) with internal battery connector |
| 292 | IT consumable (Camera USB Cable (1.5 Meter)) Micro USB to USB A cable 1.5 mtr for Canon Camera |
| 293 | IT consumable (Tripod) SIMPEX 3600 or equivalent Tripod |
| 294 | SECURITY WORKS-CCTV Surveillance SystemMinimum 2 Megapixel, IP dome camera, 2.8 ~ 12.0 mm varifocal lens, up to 30 m IR range, IR cut filter with auto switch, POE/12VDC, PAL, H.264, ONVIF compliant, |
| 295 | Minimum 2 Megapixel, bullet type camera, 2.8 ~ 12.0 mm varifocal lens, IR range 20-30 m, IR cut filter with auto switch, POE/12VDC, PAL, H.264, IP 67, ONVIF compliant |
| 296 | 24 Port POE Network Swich |
| 297 | 08 Port POE Network Swith |
| 298 | 32 Channel networkable H.264 NVR with 32 TB HDD, DVD-RW , 8 sata interface which support 6 to 10 TB capacity for each HDD |
| 299 | 16 CH NVR with 16 TB HDD |
| 300 | 08 TB Surveillance HDD |
| 301 | 32\\" LED monitor with HDMI Port and wall mounted bracket |
| 302 | Wire less Mouse |
| 303 | Full Height NVR Rack 42 U |
| 304 | 2 U Rack |
| 305 | Access Control System2 Reader networkable access control panel with 12V, 7AH battery backup and metal panel |
| 306 | 2 Reader networkable access control panel with 12V, 7AH battery backup and metal panel |
| 307 | Licence for readers |
| 308 | Smart Card Reader (HID iClass) |
| 309 | Electromagnetic lock (single leaf) |
| 310 | Electromagnetic lock (Double leaf) |
| 311 | LZ Bracket for EML |
| 312 | U Bracket for LML for Glass door |
| 313 | Exit Release Switch |
| 314 | Emergency door release(Double Pole) |
| 315 | EDR alarm Voice Unit |
| 316 | Emergency door release Lock & Key installed at Reception control by Security |
| 317 | Access cards |
| 318 | Magnetic contact for Door Held Open alarm |
| 319 | Intrusion Detection System8 Zones Intruder Alarm Control Panel includes 1 No. with inbuilt power supply unit and 12V, 7AH battery Back-up |
| 320 | Expandable Zone unit |
| 321 | Separate keypad for arming/disarming |
| 322 | panic switch |
| 323 | Motion detector with appropriate brackets |
| 324 | Hooters |
| 325 | Relay Control-12VDC ,1A-Sugar Cube |
| 326 | Push bar with MC for FE door |
| 327 | Sim based Router |
| 328 | IP Based Converter for CMS Monitoring |
| 329 | Fire Detection System - Addressable 2 loop intelligent Conventional fire detection panel with touch screen user interface, up to 200 addresses per loop with integral battery (2 x 12AH) and power supply |
| 330 | Repeater panel with large versatile touchscreen user interface, full network capability up to 126 panels, programmable as an active or passive repeater, plug and play (all system information is uploaded through the network), Integral battery and power supply |
| 331 | smoke Detector |
| 332 | Hooter with strobe light |
| 333 | Response Indicator |
| 334 | Surface mounted Manual Call Point |
| 335 | 3 channel I/O unit (for access deactivation, AHU cut off, tripping the lifts) |
| 336 | Fire Extinguisher 02 KG ABC DCP Fire Extinguisher |
| 337 | 2 KG CO2 Fire Extinguisher |
| 338 | 4.5 KG CO2 Fire Extinguisher |
| 339 | Floor Stand - Steel |
| 340 | MiscellaneousSelf contained exit lights |
| 341 | Florescent Emergency Evacuation plan - A2 Size, sandwich board type , drawing of routes and Printing |
| 342 | Security Posters set - A3 Size , Foam board |
| 343 | Photo luminescent Fire Extinguisher Signages |
| 344 | Door Frame Metel Detectors |
| 345 | Wheel Chair |
| 346 | Emergency Evacuation wheel chair |
| 347 | walky Talky - Licece free |
| 348 | HHMD Please Enable Macros to View BoQ information |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
| 5 | Click here to download tender document | Tender Documents |
| 6 | Click here to download tender document | Tender Documents |
| 7 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
